TNR-I&S-02
INSTALLATION & SERVICE MANUAL
HIGH EFFICIENCY COMMERCIAL GAS WATER HEATER
TEMPERATURE & PRESSURE RELIEF VALVE
WARNING
DANGER
Use only vent terminals provided or factory authorized terminals for
venting this water heater.
If the information in these instructions is not followed exactly, a
fire or explosion may result causing property damage, personal
injury or death.
This water heater is equipped with an adjustable thermostat to control
water temperature. Hot water temperatures required for automatic
dishwasher and laundry use can cause scald burns resulting in serious
personal injury and/or death. The temperature at which injury occurs
varies with the person’s age and the time of exposure. The slower
response time of disabled persons increases the hazards to them. NEVER
allow small children to use a hot water tap, or to draw their own bath water.
NEVER leave a child or disabled person unattended in a bathtub or shower.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
telephone in your building.
• Immediately call your gas supplier from a neighbor’s
telephone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
Failure to properly install the vent and air intake (if applicable) system
could result in property damage, personal injury, or death.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
WARNING
Keep clear of the combination temperature and pressure relief
valve discharge line outlet. The discharge may be hot enough to
cause scald injury. The water is under pressure and may splash.
TABLE OF CONTENTS
GENERAL INFORMATION ...................................................... 1
INSTALLATION .................................................................. 2
Locating The Water Heater ........................................... 2
Minimum Clearances ..................................................... 2
Venting ........................................................................ 6
Combustion Air Supply ................................................. 19
Water Connections ....................................................... 4
Gas Connections .......................................................... 14
GENERAL OPERATION........................................................... 15
MAINTENANCE ..................................................................... 17
TROUBLESHOOTING GUIDE .................................................. 20
For protection against excessive temperatures and pressure, install
temperature and pressure protective equipment required by local codes,
but not less than a combination temperature and pressure relief valve
certified by a nationally recognized testing laboratory that maintains periodic
inspection of production of listed equipment or materials as meeting the
requirements of the Standard for Relief Valves and Automatic Gas Shutoff
Devices for Hot Water Supply Systems, ANSI Z21.22 and the Standard
CAN1-4.4 Temperature, Pressure, Temperature and Pressure Relief Valves
and Vacuum Relief Valves. The combination temperature and pressure
relief valve must be marked with a maximum set pressure not to exceed
the maximum working pressure of the water heater. The combination
temperature and pressure relief valve rating must not be less than the
hourly rating of the water heater.
GENERAL INFORMATION
Install the combination temperature and pressure relief valve into the
opening provided and marked for this purpose on the water heater.
Note: Some models may already be equipped or supplied with an installed
combination temperature and pressure relief valve. Verify that the
combination temperature and pressure relief valve complies with local
codes. If the combination temperature and pressure relief valve does not
comply with local codes, replace it with one that does.
Install a discharge line so that water discharged from the combination
temperature and pressure relief valve will exit within six (6) inches (15.2
cm) above, or any distance below the structural floor and cannot contact
any live electrical part. The discharge line is to be installed to allow for
complete drainage of both the combination temperature and pressure
relief valve and the discharge line. The discharge opening must not be
subjected to blockage or freezing. DO NOT thread, plug or cap the discharge
line. It is recommended that a minimum clearance of four (4) inches (10.2
cm) be provided on the side of the water heater for servicing and
maintenance of the combination temperature and pressure relief valve.
Do not place a valve between the combination temperature and pressure
relief valve and the tank!
This gas-fired water heater is design certified by CSA International under
the American National Standard, Z21.10.3 (as indicated on the rating
plate) and CAN/CGA 4.3-M (as indicated on the rating plate) available
from CSA Standards Association, 178 Rexdale Blvd., Etobicoke, Ontario,
Canada M9W 1R3.
This water heater must be installed in accordance with local codes. In the
absence of local codes, it must be installed in compliance with the National
Fuel Gas Code (ANSI Z223.1-Latest Edition), or in Canada CAN/CGA B149.1
Natural Gas Installation Code (Latest Edition) or CAN/CGA B149.2 Propane
Installation Code (Latest Edition).
DANGER
DO NOT store or use gasoline or other flammable, combustible, or corrosive
vapors and/or liquids in the vicinity of this or any other appliance.
DO NOT install any damaged venting system components. If damage is
evident then please contact the supplier where the water heater was
purchased or the manufacturer listed on the rating plate for replacement
parts.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
AIR REQUIREMENTS
1. Do not obstruct the flow of combustion and ventilating air.
• If horizontal ducts are used, each opening shall have a free area
of not less than one square inch per 2000 Btu/hr of the total input
of all appliances in the enclosure.
2. For safe operation, adequate air is needed for combustion and
ventilation. Sooting may result in serious damage to the water heater 3. If the water heater is installed as a direct vent (outside air piped
and risk of fire or explosion. It can also create a risk of asphyxiation.
Such a condition often will result in a yellow, luminous burner flame,
causing carboning or sooting of the combustion chamber, burner and
flue tubes.
directly to the water heater), then additional opening, other than
the opening for the air intake, are not required. However, adequate
ventilation air must be provided in all cases to prevent increased
room temperature.
MECHANICAL EXHAUSTING OF ROOM AIR
CHEMICAL VAPOR CORROSION
1. Where an exhaust fan is installed in the same room with this water Corrosion of the flue ways and vent system will occur if air for combustion
heater and combustion air is drawn from inside the room, sufficient contains certain chemical vapors. Such corrosion may result in poor
openings for air must be provided in the walls.UNDERSIZED combustion and create a risk of asphyxiation. Spray can propellants,
OPENINGS WILL CAUSE AIR TO BE DRAWN INTO THE ROOM THROUGH cleaning solvents, refrigerator and air conditioning refrigerants, swimming
THE WATER HEATER’S VENTING SYSTEM, CAUSING POOR COMBUSTION pool chemicals, calcium and sodium chloride, waxes and process chemicals
THAT MAY BE HAZARDOUS TO LIFE. SOOTING MAY RESULT IN SERIOUS are corrosive. Products of this sort should not be stored near the water
DAMAGE TO THE WATER HEATER AND RISK OF FIRE OR EXPLOSION heater or outside by the air intake (if applicable).
WHICH CAN ALSO CREATE A RISK OF ASPHYXIATION. Refer to local
codes and /or National Fuel Gas Code for proper air opening sizing.
TYPICAL INSTALLATION ILLUSTRATION
UNCONFINED SPACE
1. In buildings of conventional frame, brick or stone construction,
CAUTION
unconfined spaces may provide adequate air for combustion and
If building cold water supply has a back-flow preventer, check valve
ventilation.
or water meter with check valve provisions for thermal expansion of
water in the hot water system must be provided.
2. If the unconfined space is within a building of tight construction
(buildings using the following construction: weather stripping, heavy
insulation, caulking, vapor barrier, etc.), air for combustion and
ventilation must be obtained from outdoors. This may be
accomplished by piping air directly to the water heater from outside
Figure 2
Typical Front Inlet Connection
or providing opening or ducts in the wall. The installation instructions
for confined spaces in tightly constructed buildings must be followed
to ensure adequate air supply.
CONFINED SPACE
1. When drawing combustion air from inside a conventionally
constructed building to a confined space, such a space shall be
provided with two permanent openings.
• The top opening is to be located within twelve (12) inches of the
enclosure top and the bottom opening within twelve (12) inches
of the enclosure bottom.
• Each opening shall have a free area of at least one square inch
per 1000 Btu/hr of the total input of all appliances in the enclosure,
but not less than 100 square inches.
2. If the confined space is within a building of tight construction, air for
combustion and ventilation must be obtained from outdoors. This
may be accomplished by piping air directly to the water heater from
outside or providing opening or ducts in the wall. When directly
communicating with the outdoors through vertical ducts, two
permanent openings, located in the above manner, shall be provided.
• Each opening shall have a free area of not less than one square
inch per 4000 Btu/hr of the total input of all appliances in the
enclosure.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Figure 3
Figure 6 Typical Four Water Heater Connection
Typical Front Inlet Connect with Storage Tank
WATER CONNECTIONS
WARNING
Failure to install and maintain a new, listed temperature and pressure
relief valve will release the manufacturer from any claim, which might
result from excessive temperature and pressures.
Hydrogen gas can be produced in an operating water heater that has
not had water drawn from the tank for a long period of time (generally
two weeks or more). HYDROGEN GAS IS EXTREMELY FLAMMABLE. To
prevent the possibility of injury under these conditions, we recommend
the hot water faucet to be open for several minutes at the kitchen sink
before you use any electrical appliance, which is connected to the hot
water system. If hydrogen is present, there will be an unusual sound
such as air escaping through the pipes as hot water begins to flow. Do
not smoke or have open flame near the faucet at the time it is open.
Figure 4
Typical Two Water Heater Connection
Keep clear of the combination temperature and pressure relief valve
discharge line outlet. The discharge may be hot enough to cause scald
injury. The water is under pressure and may splash.
CAUTION
If sweat fittings are to be used, DO NOT apply heat to the nipples in
front or side of the water heater. Sweat the tubing to the adapter
before fitting the adapter to the water connections. It is imperative
that heat is not applied to the nipples containing a plastic liner.
INSTRUCTIONS FOR CONNECTIONS
Figure 5
Typical Three Water Heater Connection
1. BEFORE PROCEEDING WITH THE INSTALLATION, CLOSE THE MAIN
WATER SUPPLY VALVE. After shutting off the main water supply,
open a faucet to relieve the water line pressure to prevent any
water from leaking out of the pipes while making the water
connections to the water heater. The COLD water inlet and HOT
water outlet are identified on the water heater. Make the proper
plumbing connections between the water heater and the plumbing
system to the house. Install a shut-off valve in the cold water
supply line.
2. If this water heater is installed in a closed water supply system, such
as the one having a back-flow preventer in the cold water supply,
provisions must be made to control thermal expansion. DO NOT
operate this water heater in a closed system without provisions for
controlling thermal expansion. Warranties do not cover damages
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
from thermal expansion such as pressure bulges and/or deformities.Your
water supplier or local plumbing inspector should be contacted on how
to control this situation.
Table 1
Approximate Time/Temperature Scald Chart
APPROXIMATE TIME/TEMPERATURE
RELATIONSHIPS IN SCALDS
3. After installation of the water lines, open the main water supply valve
and fill the water heater. While the water heater is filling, open
several hot water faucets to allow air to escape from the water system.
When a steady stream of water flows through the faucets, close them
and check all water connections for possible leaks.
120° F
125° F
130° F
135° F
140° F
145° F
150° F
155° F
More than 5 minutes
1½ to 2 minutes
About 30 seconds
About 10 seconds
Less than 5 seconds
Less than 3 seconds
About 1½ seconds
About 1 second
4. Never operate the water heater without first being certain it is filled
with water.
SCALDING
This water heater can deliver scalding temperature water at any faucet in
the system. Be careful whenever using hot water to avoid scalding injury.
Certain appliances such as dishwashers and automatic clothes washers
may require increased temperature water. By setting the thermostat on
this water heater to obtain the increased temperature water required by
these appliances, you may create the potential for scald injury. To protect
against injury, you should install ASSE approved mixing valve in the water
system. This valve will reduce point of discharge temperature by mixing
cold and hot water in branch supply lines. Such valves are available from
the local plumbing supplier.
ALTERNATE SPACE HEATING WATER CONNECTIONS
DANGER
Toxic chemical, such as those used for boiler treatment, shall not be
introduced into potable water used for space heating.
This water heater shall not be connected to an existing heating
system or component(s) previously used with a non-potable water
heating appliance.
All piping components connected to this water heater for space
heating applications must be suitable for use with potable water.
Figure 7
Scald Warning
WARNING
When the system requires water for space heating at temperatures
higher than required for other means, a tempering valve shall be
installed to temper the water for those uses in order to reduce the
scald hazard potential.
Failure to properly pipe this water heater may result in improper
operation and damage to the water heater or structure.
Oxygen contamination of this water heater will cause corrosion of iron
and steel components, and can lead to water heater failure.
Connect the system supply and return piping to the water heater.
Refer to Figure 8 and Figure 9 for installation examples. Maintain a
minimum ½” clearance from hot water piping to combustible materials.
Figure 8
Alternate Space Heating Connections
The following chart details the relationship of water temperature and time
with regard to scald injuy and may be used as a guide in determining the
safest water temperature for your applications.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Figure 9
Typical Plumbing Schematic for Zoned Heating
TuboCharger Water Heater
VENTING
WARNING
CAUTION
The vent shall terminate a minimum of 12 inches above expected
snowfall level to prevent blockage of vent termination.
The vent system must be properly installed. Failure to properly install
the vent system could result in property damage, personal injury, or
death.
The horizontal centerline of the exhaust vent terminal (if applicable)
must not be located lower than the horizontal centerline of the air
intake terminal if vented through the same wall.
A service drain loop must be installed in the drain tubing to serve as
a condensate trap to prevent flue gases from escaping in the room.
DO NOT position air intake terminal above exhaust terminal.
NEVER locate air intake terminal when exhaust gases can be introduced.
DO NOT install damaged venting system components. If damage is
evident then please contact the supplier where the water heater was
purchased or the manufacturer listed on the rating plate for
replacement parts.
NOTICE
Use only the vent terminals provided or factory authorized terminals
for venting this water heater.
Before beginning installation of any vent pipe, read the vent pipe
manufacturer’s installation instructions.
Water heater must be protected from freezing downdrafts during
shutdown periods.
The water heater requires its own separate venting system. Do not
connect the exhaust vent into an existing vent pipe or chimney.
Provide protection of the building materials from degradation by flue
gases from the exhaust vent terminal.
All of the exhaust venting connections must be leak checked with a
soap solution upon initial start up of the water heater. Any leaks must
be repaired before continuing operation of the water heater.
The venting instructions must be followed to avoid restricted combustion
or recirculation of flue gases. Such conditions cause sooting or risks of fire
and asphyxiation.
Do not terminate the venting where noise from the exhaust or intake
will be objectionable. This includes locations close to or across from
windows and doors. Avoid anchoring the vent and intake pipes directly
to framed walls, floors, or ceilings unless rubber isolation pipe hangers
are used. This prevents any vibrations from being transmitted into the
living spaces.
This water heater can be installed as either a direct vent system or power
vent (air from inside) system. If it is installed as a direct vent system,
then the air intake and the exhaust vent are piped to the outside. If a
power vented system is used, then air is drawn from inside and only the
exhaust is piped to the outside. Determine which system is best for your
application and install as described in the following sections.
Do not exceed the venting distances or the number of elbows listed in
this manual. Exceeding the maximum venting distances may cause
the water heater to malfunction or cause an unsafe condition.
DIRECT VENT INSTALLATION
Venting may be run horizontally through an outside wall or vertically
through a roof through using either 3 inch (7.6 cm) or 4 inch (10.2 cm)
diameter PVC or CPVC pipe. This water heater is supplied with a 3 inch PVC
screened intake and exhaust 90° elbow referred to as the exhaust vent
terminal and the air intake terminal.
DO NOT operate this water heater until the venting installation is
complete and the piping completed. Failure to complete installation
before operation can result in property damage, personal injury, or
death.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
EXCEPTIONS FOR INSTALLATIONS
The vent terminal must not terminate:
NOTICE
If 4 inch PVC or CPVC pipe is used, then a 4 inch PVC or CPVC screened
intake and exhaust 90° elbow is required.
1. Directly above a paved sidewalk or paved driveway which is located
between two single-family dwellings and serves both dwellings;
2. Less than 7 feet (2.1 m) above a paved sidewalk or a paved
driveway located on public property;
3. Within 6 feet (1.8 m) of a mechanical air supply inlet to any
building;
Direct Vent Terminal Location
Plan the vent system layout so that proper clearances are maintained
from plumbing and wiring. Before the vent is installed, determine the vent
pipe termination location as shown below in Figure 10.
Figure 10
Vent Terminal Location
4. Above a gas meter/regulator assembly within 3 feet (0.9 m)
horizontally of the vertical centerline of the regulator;
Vent terminals must terminate at least 3 feet (0.9 m) above any forced air inlet
located within 10 feet (3.1 m). This provision does not apply to:
5. Within 6 feet (1.8m) of any gas service regulator vent outlet;
6. Less than 1 foot (30.5 cm) above grade level;
7. Within 12 inches (30.5 cm) of a window or door, which can be
opened in any building, any non-mechanical air, supply inlet to any
building or the combustion air inlet of any other appliance;
8. Underneath a veranda, porch or deck, unless:
1. The combustion air intake of a direct vent appliance or the circulating air
inlet and flue gas discharge of listed outdoor appliances.
2. The exhaust vent terminal must be installed with at least 12 inches (30 cm)
clearance from any air opening into a building.
3. The bottom of the exhaust vent and combustion air intake terminals must
be located at least 12 inches (30 cm) above grade and above the anticipated
snow level.
4. Must be installed at least 3 feet (0.9 m) from any gas meter, gas valve or
other gas regulating equipment.Must be installed in a location where it will
not be blocked by snow.
•
The veranda, porch or deck is fully open on a minimum of two
sides beneath the floor and
•
The distance between the top of the vent termination and the
underside of the veranda, porch or deck is greater than 1 foot
(30.5 cm).
5. The exhaust vent and combustion air intake terminals must be installed so
that the centerline distances are at least 18 inches (45.7cm) apart and the
exhaust vent terminal elbow extends 6 inches(15.2 cm) past the combustion
air intake terminal.
The vent system must terminate so that proper clearances are maintained
as cited in local codes or the latest edition of the National Fuel Gas Code,
ANSI Z223.1.73.4e and 7.8a, b as follows:
1. Do not terminate the exhaust vent terminal over public area where
condensate or vapor can cause nuisance or hazard.
2. For direct vent, the venting system shall terminate at least 1 foot
below, 1 foot horizontally from or 1 foot above any door, window,
or gravity air inlet into building.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
3. For horizontal, the venting system shall terminate 4 foot below, 4 2. Use the proper PVC cement to secure the 90° exhaust vent and air
foot horizontally from or 1 foot above any door, window, or gravity
air inlet into building.
4. The manufacturer also recommends the vent system terminations
not be installed closer than 3 feet from an inside corner of an L
shaped structure.
5. The vent termination shall not be mounted directly above or within
3 feet horizontally from an oil tank vent or gas meter to avoid
potential freeze-up from condensation.
intake terminals provided with the water heater to the plastic pipes.
The distance between the back edge of the 90° exhaust vent terminal
and the exterior wall (see Figure 11) must be 6 inches (12.7 cm)
more for the exhaust vent terminal than the air intake terminal. Use
the proper cement or sealant and assembly procedures to secure the
vent connector joints between the terminal and the blower outlet.
Provide support brackets for every 3 feet (.91 m) of horizontal vent.
6. The vent shall terminate a minimum of 12 inches above expected
snowfall level to prevent blockage of vent termination.
Figure 11. Typical Horizontal Direct Vent System
Vent pipes serving power vented appliances are classified by building
codes as “vent connectors”. Required clearances from combustible materials
must be provided in accordance with information in this manual under
LOCATION OF WATER HEATER and CLEARANCES, and with National Fuel Gas
Code and local codes.
NOTICE
This unit can be vented using only PVC (Class 160, ASTM D-2241 Schedule
40, ASTM D-1785; or Cellular Core Schedule 40 DWV, ASTM F-891),
Schedule 40 CPVC (ASTM F-411). The fittings, other than the
TERMINATIONS should be equivalent to PVC-DWV fittings meeting ASTM
F-2665. (Use CPVC fittings, ASTM F-438 for CPVC pipe.) If CPVC pipe
and fittings are used, then the proper cement must be used for all
joints, including joining the pipe to the Termination (PVC material). PVC
materials should use ASTM –D2564 grade cement; CPVC materials
should use ASTM F-493 grade cement.
For water heaters in locations with high ambient temperatures (above
100° F) and/or insufficient dilution air, it is recommended that CPVC
pipe and fittings (MUST USE SUPPLIED VENT TERMINAL) be used.
Vertical Installation:
Vertical venting system must be supported every 5 feet of vertical run
and every 3 feet of horizontal run of vent pipe length.
Horizontal Installation:
Stress levels in the pipe and fittings can be significantly increased by
In a horizontal application, it is important that condensate not be allowed improper installation. If rigid pipe clamps are used to hold the pipe in
to buildup in the exhaust vent pipe. To prevent this from happening the place, or if the pipe cannot move freely through a wall penetration, the
pipe should be installed with an slight upward slope so the condensate will pipe may be directly stressed, or high thermal stresses may be formed
run back toward the water heater. The vent system should be supported when the pipe heats up and expands. Install accordingly to minimize such
every 5 feet of vertical run and every 3 feet of horizontal run of vent pipe stresses.
length.
Follow the following procedure to vent through the roof:
Stress levels in the pipe and fittings can be significantly increased by 1. Cut the necessary holes through the roof and ceiling.
improper installation. If rigid pipe clamps are used to hold the pipe in 2. Install the exhaust vent and air intake plastic pipes as shown in
place, or if the pipe cannot move freely through a wall penetration, the
pipe may be directly stressed, or high thermal stresses may be formed
when the pipe heats up and expands. Install accordingly to minimize such
stresses.
Figure 12. Make sure that the installation meets the local codes
and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or
CGA/CAN B149 Installation Code.
Follow the following procedure to vent through the wall:
1. Cut two 3 1/2 in. (8.9 cm) diameter holes (for 3" (7.6 cm) diameter
pipe) or 4 ½” (11.4 cm) diameter holes (for 4" (10.2 cm) diameter
pipe) in the wall with the centerline hole distances at least 18"
(45.72 cm) apart in the location where the exhaust vent and air
intake terminals will exit the outside wall if vented on the same wall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Table 2
Figure 12
Typical Vertical Direct Vent System Installation
Direct Vent Maximum Vent Length
Rated Max Vent Length (ft) Max Vent Length (ft)
Storage
Capacity
Input
3" PVC or CPVC
4" PVC or CPVC
(Gallons) (BTU/HR)
1 2 0
1 0 0
8 0
1 2 0
1 0 0
8 0
1 7 0
1 5 0
1 3 0
1 7 0
1 5 0
1 3 0
1 1 0
1 0 0
6 0
6 0
6 0
1 0 0
1 0 0
1 0 0
1 0 0
1 0 0
125,000
150,000
199,000
150,000
199,999
250,000
300,000
399,999
6 0
5 0
Determining required vent length:
1. Determine the total length of straight vent pipe (in feet) required
for both the intake and the exhaust.
2. Add 5 feet of venting for every 90° elbow.
3. Add 2 ½ feet of venting for every 45° elbow.
4. Total vent length can not exceed “Max Vent Length” in
Table 2.
5. Air intake can not exceed exhaust by more than 30 feet in
Through The Wall Venting with Low Ground Clearance:
any venting situation.
When venting cannot exit through the wall at a height greater than or
equal to 12" (30.5 cm) (and above expected snow level) from the ground,
then the installation must be modified as shown below (see Figure 13).
NOTICE
DO NOT include the 3" exhaust elbow or vent terminals in
determining maximum vent length.
Figure 13
POWER VENT INSTALLATION
Vent Terminal (Low Ground Clearance)
Power venting is where the indoor air is used and the exhaust is vented to
the outside. Venting may be run horizontally through an outside wall or
vertically through a roof through using either 3 inch (7.6 cm) or 4 inch
(10.2 cm) diameter PVC or CPVC. This water heater is supplied with a
screened intake and exhaust 90° elbow referred to as the exhaust vent
terminal and the air intake terminal.
Power Vent Terminal Location
Refer to the “Direct Vent Terminal Location” (see page 7) section
previously mentioned to determine the proper exhaust vent location.
Plan the vent system layout so that proper clearances are maintained
from plumbing and wiring. Vent pipes serving power vented appliances
are classified by building codes as “vent connectors”. Required
clearances from combustible materials must be provided in accordance
with information in this manual under LOCATION OF WATER HEATER
and CLEARANCES, and with National Fuel Gas Code and local codes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Figure 14
Typical Horizontal Power Vent System
NOTICE
This unit can be vented using only PVC (Class 160, ASTM D-2241
Schedule 40, ASTM D-1785; or Cellular Core Schedule 40 DWV, ASTM
F-891), Schedule 40 CPVC (ASTM F-411) pipe. The fittings, other
than the TERMINATIONS should be equivalent to PVC-DWV fittings
meeting ASTM F-2665. (Use CPVC fittings, ASTM F-438 for CPVC pipe.)
If CPVC pipe and fittings is used, then the proper cement must be
used for all joints, including joining the pipe to the Termination (PVC
material). PVC materials should use ASTM –D2564 grade cement;
CPVC materials should use ASTM F-493 grade cement.
For water heaters in locations with high ambient temperatures (above
100° F) and/or insufficient dilution air, it is recommended that CPVC
pipe and fittings (MUST USE SUPPLIED VENT TERMINAL) be used.
Horizontal Installation:
In a horizontal application, it is important that condensate not be allowed
to buildup in the exhaust vent pipe. To prevent this from happening, the
pipe should be installed with an slight upward slope. The vent system
should be supported every 5 feet of vertical run and every 3 feet of
horizontal run of vent pipe length.
Vertical Installation:
Vertical venting must be supported every 5 feet of vertical run and every 3 feet
of horizontal run of vent pipe length.
Stress levels in the pipe and fittings can be significantly increased by improper
installation. If rigid pipe clamps are used to hold the pipe in place, or if the pipe
cannot move freely through a wall penetration, the pipe may be directly
stressed, or high thermal stresses may be formed when the pipe heats up and
expands. Install accordingly to minimize such stresses.
Stress levels in the pipe and fittings can be significantly increased by
improper installation. If rigid pipe clamps are used to hold the pipe in
place, or if the pipe cannot move freely through a wall penetration, the
pipe may be directly stressed, or high thermal stresses may be formed
when the pipe heats up and expands. Install accordingly to minimize such
stresses.
Follow the following procedure to vent through the roof:
1. Cut the necessary holes through the roof and ceiling.
Follow the following procedure to vent through the wall:
1. Cut one 3 ½ in. (9.0 cm) diameter hole (for 3" (7.6 cm) diameter
pipe) or 4 ½” (11.5 cm) diameter hole (for 4" (10.2 cm) diameter
pipe).
2. Install the exhaust vent and air intake plastic pipes as shown in
Figure 15. Make sure that the installation meets the local codes
and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or
CGA/CAN B149 Installation Code.
2. Use the proper PVC cement or sealant to secure the 90° exhaust vent
terminal provided with the water heater to the plastic pipes. The
distance between the back edge of the 90° exhaust vent terminal and
the exterior wall (see Figure 14) must be 6 inches (13.0 cm). Use the
proper cement and assembly procedures to secure the vent connector
joints between the terminal and the blower outlet. Provide support
brackets for every 3 feet (1.0 m) of horizontal vent.
Figure 15
Typical Vertical Power Vent System Installation
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Through The Wall Venting With Low Ground Clearance:
When venting cannot exit through the wall at a height greater than or
equal to 12" (30.5 cm) (and above expected snow level) from the ground,
then the installation must be modified as shown below (see Figure 16).
Refer to Tables 2 or 3 for maximum venting lengths using 3” (7.6 cm) or
4” (10.2 cm) diameter plastic pipe.
COAXIAL VENTING INSTALLATION PROCEDURE
WARNING
Improper installation, adjustment, service, or maintenance can cause
property damage, personal injury, or death. Consult a qualified installer,
service agency, or the gas supplier for information or assistance.
This kit must be used only for terminating this water heater. Do not
use this termination kit for any other appliance. Using this kit on other
appliances and/or water heaters can result in property damage, personal
injury, or death.
Figure 16
Vent Terminal (Low Ground Clearance)
DO NOT operate this water heater until the installation and assembly
of this kit is complete and the piping completed. Failure to complete
installation before operation can result in property damage, personal
injury, or death.
Before beginning any installation, be sure the main electrical disconnect
switch is in the OFF position. Electrical shock can cause personal injury
or death.
DO NOT operate this water heater with the rain cap removed or
recirculation of combustion products may occur. Water may also collect
inside larger combustion-air pipe and flow to the burner assembly.
Failure to follow this warning could result in product damage, or improper
operation, personal injury or death.
CAUTION
DO NOT use field-supplied couplings to extend pipes. Airflow
restriction will occur and the water heater pressure switches may cause
intermittent problems.
Maximum Vent Length Determination
Table 3
Vertical Installation (Recommended)
1. Become familiar with coaxial vent kit.
Direct Vent Maximum Vent Length
Storage
Capacity
Rated Max Vent Length (ft) Max Vent Length (ft)
Figure 17
Input
3" PVC or CPVC
4" PVC or CPVC
Dimensional Layout of Concentric Vent Kit
(Gallons) (Btu/Hr)
1 2 0
1 0 0
8 0
1 2 0
1 0 0
8 0
1 7 0
1 5 0
1 3 0
1 7 0
1 5 0
1 3 0
1 2 0
1 0 0
6 0
6 0
6 0
1 0 0
1 0 0
1 0 0
1 0 0
1 0 0
125,000
150,000
199,999
150,000
199,999
250,000
300,000
399,999
6 0
5 0
Figure 18
Concentric Vent Kit Part Identitication
Determining required vent length:
1. Determine the total length of straight vent pipe (in feet) required.
2. Add 5 feet of venting for every 90° elbow.
3. Add 2 ½ feet of venting for every 45° elbow.
4. Total vent length can not exceed “Max. Vent
ength” in Table 3.
2. Determine the best location for the termination kit.
3. Cut the recommended 5" diameter hole.
NOTICE
Do not include the 3" exhaust elbow or vent terminals in determining
maximum vent length.
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
7. Install rain cap and small diameter pipe assembly in roof penetration
assembly. Ensure small diameter pipe is cemented and bottomed in
Y concentric fitting.
4. Partially assemble vent kit by performing the following:
a. Cement concentric Y fitting to larger diameter pipe. (See Figure
18).
b. Cement rain cap to smaller diameter pipe. (See Figure 19).
8. Cement heater combustion-air and vent pipes to concentric y fitting
assembly (Figure 18). (See Figure 20) for proper pipe attachment.
Figure 19
Rain Cap to Small Vent Pipe Ass’y
9. Operate heater through one cycle to ensure combustion-air and vent
pipes are properly connected to concentric vent termination
connections.
Horizontal Installation:
1. Become familiar with coaxial vent kit. As shown in Figures 17 through
19.
2. Determine the best location for the termination kit.
NOTICE
Position termination where vent vapors will not damage plants/shrubs
or air conditioning equipment.
Position termination where vent vapors will not be adversely effected
by wind condition.
Position termination where it will not be damaged or be subjected to
foreign objects.
Position termination where vapors will not be objectionable.
5. Install concentric Y fitting and pipe assembly through the structure’s
hole and field-supplied roof boot/flashing. Do not allow insulation or
other materials to accumulate inside pipe assembly when installing
through the hole.
6. Secure assembly to roof structure as shown in (Figure 20) using field-
supplied metal strapping or equivalent support material.
NOTICE
3. Cut the recommended 5" diameter hole.
Ensure termination height is above the roof surface or anticipated
snow level. Figure 20. If assembly is too short to meet height
requirements, the 2 pipe supplied in the kit may be replaced by using
the same diameter pipe. DO NOT extend the overall dimension by
more than 60 in. (See Figure 17).
4. Partially assemble vent kit.
a. Cement Y concentric fitting to larger diameter kit pipe. (See Figure
18).
b. Cement rain cap to smaller diameter kit pipe. (See Figure 19).
5. Install concentric Y fitting and pipe assembly through the structure’s
hole and field-supplied roof boot/flashing. Do not allow insulation or
other materials to accumulate inside pipe assembly when installing
through the hole.
Figure 20
Concentric Vent Roof Top Attachment
6. Install rain cap and small diameter pipe assembly in concentric Y
fitting and large pipe assembly. Ensure small diameter pipe is cemented
and bottomed in concentric Y fitting.
7. Secure assembly to structure as shown in Figure 21. Ensure clearances
as shown in Figure 21.
8. Cement heater combustion-air and vent pipes to concentric Y fitting
termination assembly. (See Figure 21) for proper pipe attachment.
9. Operate heater through one cycle to ensure combustion-air and vent
pipes are properly connected to concentric vent termination
connections.
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Figure 21
Concentric Vent Side Wall Attachment
SELECTION OF MATERIALS
VENT PIPE PREPARATION
WARNING
PRIMER – It is recommended that Tetrahydrofuran (THF) be used to
prepare the surfaces of pipe and fittings for solvent welding. DO NOT use
water, rags, gasoline or any other substitutes for cleaning PVC cellular core
or CPVC surfaces. A chemical cleaner such as MEK may be used.
DO NOT attempt to start this water heater until vent pipe solvent
fumes completely clear from the room and inside the vent piping.
INITIAL PREPARATION
CEMENT – The cement should be a bodied cement of approximately 500
to 1600 centipoises viscosity containing 10-20% (by weight) virgin PVC
1. Make sure the solvent cement you are planning to use is designed for material solvated with tetrahydrofuran (THF). Small quantities of
the specific application you are attempting.
dimethylformamide (DMF) may be included to act as a retarding agent to
extend curing time. Select the proper cement; Schedule 40 cement should
2. Know the physical and chemical characteristics and limitations of the be used for Schedule 40 pipe. Never use all-purpose cements or commercial
PVC, PVC cellular core or CPVC piping materials that you are glues and adhesives to join PVC or CPVC pipe and fittings.
about to use.
SAFETY PRECAUTION: PRIMERS AND CEMENTS ARE EXTREMELY
3. Know the reputation of your pipe and cement manufacturer and their FLAMMABLE AND MUST NOT BE STORED OR USED NEAR HEAT OR OPEN
products.
FLAME. ALSO, USE ONLY IN A WELL VENTILATED AREA.
4. Know your own qualifications or those of your contractor. The solvent
welding technique of joining PVC, PVC cellular core or CPVC pipe is a
specialized skill just as any other pipe fitting technique.
5. Closely supervise the installation and inspect the finished job before
start-up.
6. Contact the manufacturer, supplier, or competent consulting agency if
you have any questions about the application or installation of PVC,
PVC cellular core or CPVC pipe.
7. Take the time and effort to do a professional job. Shortcuts will only
cause you problems and delays in start-up. The majority of failures in
these systems are the result of shortcuts and/or improper joining
techniques.
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
GAS CONNECTIONS
WARNING
Figure 22
Drip Leg
Connect this water heater only to the type of gas as shown on the
rating plate. Use clean black iron pipe or equivalent material approved
by local codes and ordinances. (Dirt and scale from the pipe can enter
the gas valve and cause it to malfunction). The inlet gas line must
have at least a 3 inch (7.62 cm) drip leg (sediment trap) installed as
close to the water heater’s gas valve as possible. A ground joint union
must be installed in the gas supply line, as close to the water heater as
possible, to permit servicing of the water heater. Compounds used on
the threaded joints of the gas piping must be resistant to the action of
liquefied petroleum gases/propane gas. DO NOT apply pipe dope to
the gas valve inlet and make certain that no pipe dope has become
lodged in the inlet screen of the gas valve. Extreme care must be
taken to ensure no pipe dope enters the gas valve and to avoid
excessive torque when tightening the gas supply line to the gas valve.
Excessive torque may result in cracking of the gas valve housing. The
suggested maximum torque is 31.5 foot lbs. (4.4 kg-m). The
manufacturer of this water heater will not be liable for any damage or
injury caused as a result of a cracked gas inlet as a result of excessive
torque.
The gas supply lines must meet all requirements of the National Fuel Gas
Code ANSI Z223.1 (Latest Edition), or in Canada CAN/CGA B149.1 Natural
Gas Installation Code (Latest Edition) or CAN/CGA B149.2 Propane
Installation Code (Latest Edition).
GAS METER SIZE – NATURAL GAS ONLY
Be sure that the gas meter has sufficient capacity to supply the full rated
gas input of the water heater as well as the requirements of all other gas
fired equipment supplied by the meter. If the gas meter is too small, ask
the gas company to install a larger meter having adequate capacity.
This water heater and its gas connection must be leak tested before
placing the water heater in operation. Check for gas leaks with a soap
and water solution and a brush or a commercial leak detector fluid.
NEVER USE A MATCH OR OPEN FLAME FOR TESTING!
GAS PRESSURE REGULATION
Main line gas pressure to the water heater should be between a maximum
14.0 inch W.C. and a minimum supply pressure as shown on the rating
plate. The inlet gas pressure must not exceed the maximum value.
The water heater is not intended for operation at higher than 14.0 inch
water column (½ psi) supply gas pressure. Higher gas supply pressures
require supplemental reducing service regulation. Exposure to higher
gas supply pressure may cause damage to the gas controls which
could result in fire or explosion. If overpressure has occurred such as
through improper testing of gas lines or emergency malfunction of the
supply system, the gas valve must be checked for safe operation.
Make sure that the outside vents on the supply regulators and the
safety vent valves are protected against blockage. These are parts of
the gas supply system, not the water heater.
BEFORE PLACING THE WATER HEATER IN OPERATION, CHECK FOR GAS
LEAKAGE. USE SOAP AND WATER SOLUTION OR OTHER MATERIAL ACCEPTABLE
FOR THE PURPOSE OF LOCATING GAS LEAKS.
WARNING
DO NOT USE MATCHES, CANDLES, FLAME OR OTHER SOURCES
OF IGNITION FOR THIS PURPOSE.
ELECTRICAL CONNECTIONS
CAUTION
WARNING
The water heater and individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of the
system at test pressures in excess of ½ psi (3.5 kPa). The water
heater must be isolated from the gas supply piping system by closing
its manual shutoff valve during any pressure testing of the gas supply
system at test pressures equal to or less than ½ psi (3.5 kPa). The
supply line must be capped when not connected to the water heater.
If copper supply lines are used, they must be internally tinned and
certified for gas service.
Turn off or disconnect the electrical power supply to the water heater
before servicing. Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
All electrical wiring must be installed and grounded in accordance with
local codes, or in the absence of local codes, the National Electrical
Code, ANSI/NFPA 70 and/or CSA C22.2 Electrical Code.
The water heater must be wired to a 120 VAC, 60 Hz, 15A power supply.
The water heater should be connected to a GFI outlet and wired on a
separate circuit and breaker. If a flexible line cord and plug is permitted
by local code, then provide a three wire GFI grounding type receptacle
within reach of the line cord provided on the control box. DO NOT plug
the line cord into a receptacle that can have the power supply interrupted
by a switch that is used to control lights or another appliance.
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
If wiring in conduit is required, remove the line cord and strain relief
bushing in the control panel and install an electrical conduit connector.
Connect the hot, neutral, and ground leads to the terminal block using
quick connect terminals. Refer to the wiring diagram for the correct
terminal locations for each wire lead.
WARNING
If the unit is exposed to the following, do not operate water heater
until all corrective steps have been made by a factory authorized
independent service contractor or qualified service professional.
1. Flooding to or above the level of the burner or controls
2. External firing
CAUTION
3. Damage
4. Firing without water
5. Sooting
Do not energize the electric circuit before the water heater tank is
filled with water.
This controller is Polarity sensitive. If the Hot and Neutral Supply
voltage is reversed, the controller will not sense flame and the water
heater will not operate. Verify polarity before connecting the water
NEVER OPERATE THE WATER HEATER WITHOUT FIRST BEING
CERTAIN IT IS FILLED WITH WATER AND A TEMPERATURE AND
PRESSURE RELIEF VALVE IS INSTALLED IN THE RELIEF VALVE
OPENING OF THE WATER HEATER.
heater.
WIRING DIAGRAM AND SCHEMATIC
Figure 23
Wiring Diagram and Schematic
GENERAL INSTRUCTIONS
OPERATING INSTRUCTIONS
WARNING
TO FILL THE WATER HEATER
1. Close the water heater drain valve by turning the knob or valve stem
clockwise. If alternative water connections are provided but not
used, make certain they are plugged (i.e. rear connections).
2. Open the cold water supply shut-off valve.
3. Open several hot water faucets to allow air to escape from the
system.
4. When a steady stream of water flows from the faucets, the water
heater is filled. Close the faucets and check for water leaks at the
water heater drain valve, combination temperature and pressure
relief valve and the hot and cold water connections.
Water heaters are heat-producing appliances. To avoid damage or
injury there must be no materials stored against the water heater or
direct vent system, and proper care must be taken to avoid
unnecessary contact (especially by children) with the water heater
and direct vent system. UNDER NO CIRCUMSTANCES SHOULD
FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE
USED OR STORED IN THE VICINITY OF THIS WATER HEATER OR IN ANY
LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER.
Installation or service of this water heater requires ability equivalent
to that of a licensed tradesman in the field involved. Plumbing, air
supply, venting, gas supply and electrical work are required.
Light the unit in accordance with the operating instructions label attached
to the water heater.
SEQUENCE OF OPERATION
1. A call for heat from thermostat
2. Blower ON
6. Main burner ON
7. Flame signal confirmed
Under no circumstances should the input rate exceed the input rate
shown on the water heater rating plate. Over firing could result in
damage or sooting of the water heater.
3. Pressure switch proves blower operation 8. Thermostat satisfied
4. Blower pre-purge
5. Igniter warm-up
9. Main burner OFF
10. Blower post-purge
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
LIGHTING INSTRUCTIONS
Figure 24 Lighting Instruction Label
1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
TEMPERATURE ADJUSTMENT
The temperature selector knob of the thermostat has been adjusted to
120° F when shipped from the factory.
Figure 25
Sight Glass Location
NOTICE
The lower the temperature setting, the greater the energy efficiency,
both to heat the water and to maintain the storage temperature
during standby periods. Lower water temperatures also extend tank
life. Remember, no water heating system will provide exact
temperatures at all times. Allow a few days of operation at this
setting to determine the correct temperature setting consistent with
the requirements for the installation.
CAUTION
This water heater, when set at a lower temperature setting is not
capable of producing hot water of sufficient temperature for sanitizing
purposes.
During the winter season or any cold period, you may desire a higher
temperature setting to adjust for the colder incoming water. This adjustment,
however, may cause additional condensation to form on the colder tank
surface. This does not mean the tank is leaking. During summer months,
the warmer incoming water temperatures will benefit the performance of
your water heater and reduce the amount of condensation developed.
MAINTENANCE
DANGER
DO NOT ATTEMPT TO REPAIR GAS VALVE.
Condensation does not mean your tank is leaking. Most of reported tank
leaks on installation are proven to be condensation. To avoid unnecessary
inconvenience and expense, make sure the tank is leaking before calling
an independent servicing contractor or qualified service professional.
DO NOT ATTEMPT TO REPAIR IGNITION MODULE.
DO NOT ATTEMPT TO REPAIR VENTURI.
DO NOT ATTEMPT TO REPAIR THERMOSTAT BOARD.
DO NOT ATTEMPT TO REPAIR TRANSFORMER.
DO NOT ATTEMPT TO REPAIR PRESSURE SWITCH.
DANGER
Hotter water increases the risk of scald injury. Scalding may occur
within 5 seconds at a temperature setting of 135°F (57°C). To protect
against hot water injury, install an anti-scald tempering valve in the
water system. This valve will reduce point of discharge temperature
by mixing cold and hot water in branch water lines. A licensed
plumbing professional or local plumbing authority should be consulted.
This water heater is equipped with an energy cut out device to
prevent overheating. Should overheating occur or the gas supply
fail to shut off, turn off the manual gas control valve to the appliance
and call a qualified service agency.
GENERAL
KEEP APPLIANCE AREA CLEAR AND FREE FROM COMBUSTIBLE MATERIALS,
GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS.
Water heater maintenance includes periodic tank flushing and cleaning,
and removal of lime scale. The unit should be inspected and adjusted to
maintain proper combustion. Refer to Table 4, “Suggested Maintenance
Schedule”. A periodic inspection of the venting system should be made.
If the water heater is to remain idle for 30 days or more or is subjected to
freezing temperatures while shut off, the water heater and piping should
be fully drained and the drain valve should be left fully open. Refer to the
“General Operation” section of this Installation and Operating Instructions
Manual for the procedure on draining the water heater.
MAINTENANCE SCHEDULE
Following are the instructions for performing some of the recommended
maintenance. Unit inspection and adjustment should be performed by a
competent technician.
BURNER FLAME CHECK
At the time of installation and at monthly intervals, a visual check of the
burner flames should be made to determine if they are burning properly.
The main burner may be seen through the sight glass window on the front
of the combustion insert mounting bracket (Figure 25). The burner flames
should be a blue flame near the burner surface in a uniform flame pattern.
Occasional yellow or white streaks are normal.
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
Table 4
Suggested Maintenance Schedule
COMPONENT
OPERATION
INTERVAL
REQUIRED
Tank
Sediment Removal
Monthly
Flushing
Anode Rods
Inspect
Semi-Annually
Semi-Annually
As Required
Every 3 Months
Annually
Replace as Required
Proper Operation
Relief Valve
Check Operation
Clean Inlet Screen
Inspect
Blower
Soft Brush
Vent & Air Intake System
Ignition System
Vent Terminal
Combustion System
Condensate Line
Joints should be sealed
Clean of dust and dirt
Remove object that caused restriction
Confirm S-OP
Inspect
Free of Shrubs & Debris
Inspect
Monthly
Monthly
Inspect
Monthly
Remove restriction
the water. This is the lime scale which forms in pipes, water heaters and on
cooking utensils.
FLUSHING WATER HEATER
1. Turn OFF the water heater electrical disconnect switch.
2. Open the drain valve and allow water to flow until it runs clean.
3. Close the drain valve when finished flushing.
Lime accumulation not only reduces the life of the equipment but also
reduces efficiency of the water heater and increases fuel consumption.
4. Turn ON the water heater electrical disconnect switch.
The usage of water softening equipment greatly reduces the hardness of
the water. However, this equipment does not always remove all of the
hardness (lime). For this reason it is recommended that a regular schedule
of deliming be maintained.
DRAINING WATER HEATER
The water heater must be drained if it is to be shut down and exposed to
freezing temperatures. Maintenance and service procedures may also
require draining the water heater.
1. Turn off the water heater electrical disconnect switch.
2. Connect a hose to the drain valve.
3. Locate hose’s discharge in an area where hot water will not cause
any damage or injury.
4. Close the cold water inlet valve to water heater.
5. Open a nearby hot water faucet to vent the system.
6. Open the heater drain valve.
7. If the water heater is being drained for an extended shutdown, it
is suggested the drain valve be left open during this period.
The depth of the buildup should be measured periodically. Water heaters
will have about 3 inches of lime buildup when the level of lime has reached
the bottom of the cleanout opening or about 1 inch of lime buildup if it has
reached the drain valve opening. A schedule for deliming should be set
up, based on the amount of time it would take for a ½ inch buildup of lime.
Example1:
Initial inspection shows ½ an inch of lime accumulation. Therefore, the
water heater can be delimed once a year.
FILLING WATER HEATER
To remove sediment and lime scale:
1. Drain the heater. Refer to DRAINING THE WATER instructions in this
section.
2. Remove outer cover plate from lower side of water heater jacket.
3. Remove cover and gasket from cleanout opening.
4. Remove lime, scale or sediment using care not to damage the
glass-lining.
5. Inspect cleanout plate gasket: Replace gasket if necessary (Contact
local distributor for correct part number).
1. Close the water heater drain valve by turning the knob or valve
stem clockwise. If alternative water connections are provided but
not used, make certain they are plugged (i.e. rear connections).
2. Open the cold water supply shut-off valve.
3. Open several hot water faucets to allow air to escape from the
system.
4. When a steady stream of water flows from the faucets, the water
heater is filled. Close the faucets and check for water leaks at the
water heater drain valve, combination temperature and pressure
relief valve and the hot and cold water connections.
6. Install gasket and cleanout plate. Be sure to draw plate up tight by
tightening screws securely.
7. Close the drain valve. Open a hot water fixture to allow air to
escape. Open the cold water supply to water heater and allow the
tank to fill. Follow the lighting instructions.
SEDIMENT AND LIME SCALE REMOVAL
Waterborne impurities consist of the particles of soil and sand which settle
out and form a layer of sediment on the bottom of the tank.
8. Check for water leakage.
9. Install outer jacket cover plate.
The amount of calcium carbonate (lime) released from water is in direct
proportion to water temperature and usage. The higher the water
temperature or water usage, the more lime deposits are dropped out of
1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
ANODE INSPECTION AND REPLACEMENT
explosion. In areas with poor water conditions, it may be necessary to
This water heater is equipped with multiple sacrificial anodes. Anodes inspect the T&P valve more often than the recommended maintenance
protect the glass-lined tank from corrosion by sacrificing themselves through schedule.
electrolysis. When the anode material is consumed, there is no more
protection and corrosion of the tank accelerates.
CAUTION
Before manually operating the valve, make sure that a drain line has
been attached to the valve to direct the discharge to an open drain.
Failure to take this precaution could mean contact with extremely hot
Inspection of the anode every 6 months allows you to identify the rate of
anode degradation. The anode should be replaced when its diameter is
3/8 of an inch, or annually which ever is first. Aggressive, very hot and
softened water causes rapid consumption of the anode requiring frequent
water passing out the valve during this checking operation.
inspections. The replacement anodes rods are available from your local If the temperature and pressure relief valve on the water heater discharges
distributor.
periodically or continuously, it may be due to thermal expansion of water
in a closed water supply system, or, it may be due to a faulty relief valve.
To inspect or replace an anode:
The anodes on this water heater are easily accessible from the top of the Thermal expansion is the normal response of water when it is heated. In a
water heater making replacement simple and quick. Use the following closed system, thermal expansion will cause the system pressure to build
procedure to remove and inspect the anodes.
until the relief valve actuation pressure is equaled. Then, the relief valve
will open, allowing some water to escape, slightly lowering the pressure.
1. Drain the heater. Refer to DRAINING THE WATER HEATER instructions
in this section.
Contact your water supplier or local plumbing inspector on how to control
2. Flush the heater. Refer to FLUSHING THE WATER HEATER instructions this situation.
in this section.
WARNING
3. Remove the combustion surround top by unlatching.
Above all, do not plug the temperature and pressure relief valve. This
is not a solution and can create a hazardous situation.
4. Remove the second pass access cover. (If equipped)
5. Remove the second pass insulation.
6. Remove the second pass collector cover.
7. Remove the anode using a socket of the appropriate size. Sometimes VENT AND AIR INTAKE SYSTEM
a breaker bar will need to be used. DO NOT use an impact wrench. Examine the vent and air intake system every 3 months. Points of inspection
8. Inspect and replace the anode as required. Use pipe tape or sealant are as follows:
when reinstalling the anode.
9. Close the drain valve. Open a hot water fixture to allow air to escape.
1. Check for obstructions and/or deterioration of vent piping and vent
terminal. Replace immediately where needed.
Open the cold water supply to water heater and allow the tank to fill. 2. Vent pipe and vent hood screen should be cleaned of any foreign
Follow the lighting instructions.
material. The screen is located inside the vent hood outlet and is
accessible from the outside of the hood. DO NOT reach inside the
vent hood when the water heater is in operation.
10. Check your anode and drain valve for leaks.
11. Replace second pass collector cover. Make sure to clean off any
sealant and reseal before fastening.
3. Check all vent system connections for leakage and reseal as required.
12. Replace second pass insulation.
13. Replace second pass access cover.
14. Replace combustion surround top and latch it securely in place. COMBUSTION SYSTEM INSPECTION
Inspect the operation of the combustion system monthly. Use the following
procedure to inspect the combustion system.
DRAIN VALVE AND TANK ACCESS PANEL
The water heaters are equipped with a ¾ inch drain valve. An access panel 1. Turn off the main power switch of the water heater.
covers the cleanout opening in the tank which is sealed by a gasket and 2. Adjust the thermostat to the Min. setting.
cover.
3. Remove the top of the combustion surround by unlatching it.
4. While observing the ignition module, turn on the main power switch.
5. Adjust thermostat to the Max. setting.
RELIEF VALVE
At least twice a year, the temperature and pressure relief valve should be 6. Watch the LED’s light as the controller goes through the S-OP as
checked to ensure that it is in operating condition. To check the relief previously described.
valve, lift the lever at the end of the valve several times. The valve should 7. Upon ignition, observe the main burner flame.
seat properly and operate freely.
8. Readjust thermostat to previous setting.
9. Replace combustion surround top and latch it securely in place.
If water does not flow, remove and inspect for obstructions or corrosion.
Replace with a new valve of the recommended size as necessary. A thorough
inspection of the valve should be performed at least every three years by
removing the temperature and relief valve from the tank. Do not attempt
to repair the valve, as this could result in improper operation and a tank
1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TNR-I&S-02
TROUBLESHOOTING GUIDE
Main power light is not lit.
Make sure that water heater is plugged in.
When the switch is on, is there 120VAC between L1 and N on the terminal block? If not, then
check for loose wire connections on the “Power Switch Wire Harness.” If connections are ok, then
replace the switch.
If there is voltage between L1 and N then the light on the switch is burnt out. Replace switch.
Thermostat does not call for heat.
Make sure that the temperature of the tank is cool.
If the thermostat does not call for heat, then check the PRIMARY voltage across the “Transformer”.
If there is voltage across the PRIMARY, then check the voltage across the SECONDARY leads of
the “Transformer”.
Install a jumper wire from N.O. terminal to the COM terminal on the “Thermostat PC Board.” If
the thermostat calls for heat after installing a jumper wire then check the “Thermostat Sensor
Probe” leads for proper resistance with an OHM meter (See appendix A).
If sensor reading are not correct, replace “Thermostat Sensor Probe.”
If the sensor readings are correct, then check “Potentiometer” for the proper resistance. If the
readings are correct, then replace the “Thermostat PC Board”, otherwise replace the
“Potentiometer.”
Ignition module “Power” LED is not lit.
Blower does not energize.
Check for 120 VAC at the ignition module on “120 VAC IN.” If there is voltage, then replace the
ignition module.
If there is not any voltage, check the voltage across the transformer as previously described.
Is the “Vacuum Switch” (air intake switch) N.C.? If no, then check the hose and see if it is filled
with condensate. If the hose is not filled with condensate, then replace vacuum switch. If filled,
empty hose.
Is the “Pressure Switch” (exhaust pressure switch) N.O.? If no, then check the hose and see if it
is filled with condensate. If the hose is not filled with condensate, then replace pressure switch.
If filled empty hose.
Is the “Collector Limit Switch” N.C.? If no, then reset switch. If this switch trips more than 3
times, call service.
If all items above are ok, then replace the blower.
Ignitor does not glow.
Is there voltage to the “Hot Surface Ignitor”? Check for 120VAC to the ignitor from the ignition
module.
Is there continuity across the “Hot Surface Ignitor?” If no, then replace hot surface ignitor. If
yes, then replace the ignition module.
Main valve does not turn on.
Put your hand on the gas valve. When the “Valve” LED lights on the ignition module, can you
feel it energize? If not, then check the voltages at the ignition module across pins 2 and 7 on
the plug “CONTROL”. If there is 24 VAC across these pins, then check to see if the “Rectifier
Harness” is secure. If it is secure, then replace the “Gas Valve”.
If you can feel the gas valve energize, check the main gas supply is not in the off position.
Burner Flame keeps going out.
Is there minimum gas supplied to water heater as stated on the rating plate? If not, then
increase the supply pressure to the water heater.
Measure the microAmps through the flame sensor using a multimeter. Is there at least 4
microAmps? If not, then replace the “Flame Sensor” or flame sensor wire.
Thermostat does not satisfy.
Blower did not post purge
Is the tank temperature above the temperature set point?
Does the T&P relief valve leak? If yes, then replace “Thermostat PC Board.”
Check “Vacuum Switch” (air intake switch) as previously mentioned.
Check “Pressure Switch” (exhaust pressure switch) as previously mentioned.
Check “Collector Limit Switch” as previously mentioned.
If above switches are all ok, then replace “Ignition Module.”
9/07 Printed in USA
2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|