2:8 Distribution Amplifier
For
d
Model # HDMI-DA-2X8M
U S E R M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
ASKING FOR ASSISTANCE
Technical Support:
Telephone
(800) 421-1587
(760) 438-7000
Fax
(760) 438-7199
Technical Support Hours:
6:30 AM - 4:30 PM PST Monday through Friday.
Email:
Website:
Notice
Linear LLC reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
© 2008 Linear LLC, All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. Introduction / Operation Notes
2. Features
3. Panel Descriptions
4. Connecting and Operating the 2:8 Distribution Amplifier For HDMI
5. Application Diagram
6. RMT-2 Installation
7. IR Code Configuration
8. RJ-11 To Serial Control Interface
9. Rack Ears Installation Diagram
10. Wiring Diagram
11. Specifications
12. Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The Linear 2:8 Distribution Amplifier For HDMI is the perfect solution for anyone who
needs to send one or two sources of digital high definition video to multiple displays
at the same time. It supports HDMI equipment, such as DVD players, satellite set
top boxes, and HDMI displays. In operation, the digital source is connected to the
distribution amplifier’s input while eight HDMI outputs are available to be used
in part or in full. Once the unit is connected and powered, your source can be
distributed up to eight digital displays at the same time.
How It Works
Simply connect your HDMI video source to the 2:8 Distribution Amplifier’s input
using the supplied HDMI cable. Then connect up to eight HDMI displays to the unit’s
eight HDMI outputs. Once connected and powered, your source will be seen on all
eight displays at the same time. When two or more 2:8’s are connected together,
you can create a larger distribution system.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 2:8 DISTRIBUTION AMPLIFIER FOR HDMI
•
Display information (EDID) is sent from the display connected to HDMI
Output Port 1 to both sources connected to the 2:8 Distribution Amplifier
for HDMI. If there is no display connected to HDMI Output Port 1, the
remaining HDMI Output Ports will be scanned in succession and use the
first EDID that it detects. (See note on page 4 for additional information)
•
The 2:8 Distribution Amplifier for HDMI can only mirror one input video signal at
a time to all eight display outputs. The user can choose which of the two HDMI
inputs will be displayed on all eight HDMI outputs.
•
•
HDMI/HDCP compliant
Compatible with all HDMI and DVI* displays
NOTE: *When used with a DVI to HDMI adapter
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Features
•
•
•
•
Switch easily between any two HDMI/DVI* sources
Outputs are mirrored to eight HDMI/DVI* displays simultaneously
Supports resolutions up to 1080p, 2K and 1920 x 1200
Extends the range of HDMI compliant devices by equalizing and re-clocking the
HDMI signal
•
HDMI/HDCP compliant
Includes:
(1) 2x8 Distribution Amplifier For HDMI
(1) 6’ HDMI cable (M-M)
(1) 24V DC Power Supply
(1) RMT2-IR remote
(1) Set of Rack Ears
(1) Users Manual
NOTE: *When used with a HDMI to DVI Adapter
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE 2:8 DISTRIBUTION AMPLIFIER FOR HDMI
How to Connect the 2:8 Distribution Amplifier For HDMI
1. Connect the supplied cable from the HDTV HDMI source into the HDMI input port 1
of the 2:8 Distribution Amplifier For HDMI.
2. Connect a second HDTV HDMI source to HDMI input port 2 on the 2:8 Distribution
Amplifier For HDMI using a user supplied HDMI cable.
3. Connect the display(s) (up to eight) to the HDMI output port(s)* of the 2:8
Distribution Amplifier For HDMI using user supplied cable(s)
4. Plug the 24V DC power supply into the 2:8 Distribution Amplifier For HDMI.
NOTE: *Display information (EDID) is sent from the display connected to
HDMI Output Port 1 to both of the sources connected to the 2:8 Distribution
Amplifier for HDMI. If there is no display connected to HDMI Output Port 1, the
remaining HDMI Output Ports will be scanned in succession and use the first
EDID that it detects. The source will output resolutions and timings according the
EDID that is being fed by the 2:8 Distribution Amplifier for HDMI. Therefore, all of
the connected displays must be capable of accepting the timings and resolution
output by the source. It is recommended that the display with the lowest native
resolution be connected to HDMI output port 1. This is to ensure that a compatible
video signal will be able to be displayed on all connected monitors.
OPERATING THE 2:8 DISTRIBUTION AMPLIFIER FOR HDMI
Switching between the inputs on the 2:8 Distribution Amplifier for HDMI is done using
either the supplied RMT2-IR remote or the RJ11 to serial interface.
IR Remote
Pressing button one on the remote will select the HDMI source that is connected to
HDMI input port one. Pressing two on the remote will select the HDMI source that is
connected to HDMI input port two.
RJ11 To Serial Control Interface
Please see the diagram on page 7 for the RJ11 serial control interface pin configuration.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATION DIAGRAM
Multiple HDMI-DA-2X8 devices can be daisy chained together to distribute a single
HDMI signal to a maximum of 73 units, for a total of 512 displays.
HDMI-DA-2X8M
HDMI-DA-2X8M
X8
HDMI-DA-2X8M
X64
Maximum 512 Displays
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RMT2-IR INSTALLATION
1. Remove battery cover from the back of the RMT2-IR remote.
2. Verify that dip switches 1 & 2 are in the down (OFF) position. (See page 6)
3. Insert the battery, hold the battery so that you can see the positive side facing up.
The side that is not marked must be facing down.
4. Test the RMT2-IR remote by pressing ONLY one button at a time. The indicator
light on the remote will flash once each time you press a button.
WARNING: Do not press multiple buttons simultaneously and do NOT press buttons
rapidly. These actions will cause the remote to reset and steps 1-4 will have to be
repeated.
Note: The RMT2-IR ships with two batteries. One battery is required for operation,
the second battery is complimentary.
The optional IR extender allows you to
relocate your HDMI Switcher and still retain IR
control. Linear part# IR-EXTENDER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IR CODE CONFIGURATION
How to Resolve IR Code Conflicts
In the event that IR commands from other remote controls conflict with the supplied RMT-2IR remote
control, changing the remote channel will alleviate this issue. The RMT-2IR remote control and the 2:8
Distribution Amplifier for HDMI have DIP SWITCHES for configuring the remote channel that both units
use to communicate. These settings must match each other for proper operation. The 2 DIP SWITCH
bank on the RMT-2IR is located underneath the battery cover. The 8 DIP SWITCH bank for the 2:8
Distribution Amplifier for HDMI is located inside of the unit. *DIP SWITCH 1 and 2 on the RMT-2IR
correspond to DIP SWITCH 3 and 4 on the 2:8 Distribution Amplifier for HDMI.
NOTE: *DIP SWITCHES 1, 2, and 5 through 8 are not used on the 2:8 Distribution Amplifier for HDMI.
Because the procedure for changing channels requires the main unit to be disassembled, this procedure
should only be done if there are IR conflicts present in your setup.
Disconnect power from unit before starting. Remove all cabling from unit.
To open the 2:8 Distribution Amplifier for HDMI Unit, remove all screws from the sides and underside of the
unit. Remove the hex nuts above each HDMI connector. Slide the unit apart carefully to expose the internal
PCB and the 8 DIP SWITCH bank.
When DIP SWITCH adjustments are complete, carefully slide the unit back together. Being careful not to
over tighten the hex nuts, screw them back in above each HDMI connector. Screw all of the screws from
the sides and underside of the unit back into the unit, again being careful not to over tighten the screws.
Plug all cabling back into its proper location on the unit. Reconnect power to the unit and test for IR
conflicts.
Remote
Remote Channel 1:
Default
Remote Channel 2:
Remote Channel 4:
1
1
2
2
1
1
2
2
Remote Channel 3:
2:8 Distribution Amplifier for HDMI
Remote Channel 1:
Default
Remote Channel 2:
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Remote Channel 3:
Remote Channel 4:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RJ-11 TO SERIAL CONTROL INTERFACE
DB-9 to RJ-11
DB-9
Pin
Description
Connects To
RJ-11 Pin
1
2
3
4
Carrier Detect
Receive Data
N/A
3
Transmitted Data
2
Data Terminal
Ready
N/A
5
6
7
8
9
Ground
1 & 6
N/A
N/A
N/A
N/A
Data Set Ready
Request To Send
Clear To Send
Ring Indicator
5
1
6 1
RJ-11 6-Pin
FRONT:
FRONT:
9
6
Female DB-9
Connectors not to scale
Binary Table
ASCII
Input
Binary
0011 0001
0011 0010
1
2
1
2
Terminal Settings
Bits per second .................................................................................................. 19200
Data bits .................................................................................................................... 8
Parity ................................................................................................................... None
Stop bits ......................................................................................................................1
Flow Control ........................................................................................................ None
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RACK EARS INSTALLATION DIAGRAM
Rack mount ears are provided for installation of this unit into a 1U rack mount
space.
1. Locate the side screws on the unit.
2. Remove the front 2 screws that are located closest to the front of the unit.
3. Using the removed screws, screw the rack mounting bracket into the unit.
4. Repeat the procedure on the opposite side of the unit.
1
Front of unit
Rear of unit
2
3
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Video Amplifier Bandwidth ............................................................................ 165 MHz
Input Video Signal ................................................................................... 1.2 Volts p-p
Input DDC Signal .............................................................................. 5 Volts p-p (TTL)
Single Link Range ........................................................................1080p / 1920 x 1200
Input Connector Type ..................................................... HDMI Type A 19 Pin Female
Output Connector Type ...................................................HDMI Type A 19 Pin Female
Remote Control Port ...................................................... RJ11 Jack For Serial Control
Power Consumption ........................................................................... 60 Watts (max.)
Power Supply .................................................................................................. 24V DC
Rack Mountable ........................................................................................... 1U Rack Space
Dimensions .............................................................................. 17”W x 1.75”H x 5.5”D
Shipping Weight .................................................................................................. 5 Lbs
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Note: These products are designed to be installed and serviced by trained professional
installation companies.
Linear LLC warrants this product to be free from defects in material and workmanship. For the
term of the warranty, see the list of products below. The Warranty Expiration Date is reflected by
a date code that is affixed to all of Linear’s products. This warranty extends only to wholesale
customers who buy direct from Linear or through Linear’s normal distribution channels. Linear
does not warrant this product to consumers. Consumers should inquire from their selling dealer
as to the nature of the dealer’s warranty. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use or performance
of this product or other indirect damages with respect to loss of property, revenue, or profit, or
cost of removal, installation or reinstallation. All implied warranties, including implied warranties
for merchantability and implied warranties for fitness, are valid only until warranty expiration date
as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or
implied. Some states and countries do not allow limitations or how long an implied warranty lasts
or the exclusion or limitation or incidental or consequential damages, so the above exclusions
may not apply. The Linear LLC warranty gives specific legal rights in addition to other rights,
which may exist and vary from state to state and country to country.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Consumers: If you have trouble locating your installing company, please contact Linear LLC at
1-800-421-1587 and we will assist you with locating a service and Installation Company.
The following warranty period applies to this set of Linear branded products.
1.
Linear High Definition Video products — Two (2) years. There is no warranty offered on the
batteries supplied with the IR remote Control.
The warranty is limited to repair or replacement of products returned, freight prepaid, to
Linear LLC. There is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS
OF ANY KIND.
1.
Failures due to product abuse, negligence, improper installation, improper use, and
electrical surge including damage from lightning, water damage or other damage due to
natural disasters are not covered by the warranty.
2.
3.
The warranty shall also be voided by any tampering with the date code, labels or other
markings on the product.
Products that are damaged in transit to Linear LLC due to improper packaging or by the
carrier (shipping company) will not be covered under the warranty. If the product was
damaged or lost by the carrier, it is the sender’s responsibility to create a claim against the
carrier.
4.
The user is responsible for all labor costs associated with removing, reinstalling and
returning the product to Linear LLC.
5.
6.
Linear LLC, at its option, will repair or replace the defective product.
Replacements will be made from B-Stock. If an exact replacement is not available Linear
LLC, at its option will select the nearest equivalent product. The user is responsible for
freight charges to Linear LLC.
7.
Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent
service. A customer may pay the additional costs for second day or next-day service.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI-DA-2X8M
(760) 438-7000
(800) 421-1587 FAX (800) 468-1340
Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|