RETURN TO MAIN MENU
IM896
August, 2006
SPREADARC
For use with machines having Code Numbers:
11006
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
ful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
OPERATOR’S MANUAL
Copyright © 2006 Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the spe-
cific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
AUG 06
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
iii
SAFETY
WELDING SPARKS can
cause fire or explosion.
CYLINDER may explode
if damaged.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
7.c. Cylinders should be located:
•Away from areas where they may be struck or subjected to
physical damage.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
•A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
FOR ELECTRICALLY
powered equipment.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
6.h. Also see item 1.c.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Mar ‘95
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
iv
SAFETY
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
Mar. ‘93
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Thank You
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
vi
TABLE OF CONTENTS
Page
General Information.....................................................................................................................1
Product Description..................................................................................................................1
Recommended processes and Equipment..............................................................................1
Design Features.......................................................................................................................1
Common Equipment Packages ...................................................................................................2
Basic Package .........................................................................................................................2
Advanced Package..................................................................................................................2
Technical Specifications ..............................................................................................................3
________________________________________________________________________________
Installation.......................................................................................................................Section A
Non-Standard Safety Information.........................................................................................A-1
Input Connections. ...............................................................................................................A-1
Location.........................................................................................................................A-1
Mounting.................................................................................................................A-2,A-3
High Frequence Protection ...........................................................................................A-3
Connection Diagram .....................................................................................................A-4
________________________________________________________________________________
Operation.........................................................................................................................Section B
Case Front Case Description ...............................................................................................B-1
Design Features...................................................................................................................B-1
User Interface Controls ........................................................................................................B-2
Power down, power Up Sequence.......................................................................................B-2
Common Welding Procedures .............................................................................................B-3
________________________________________________________________________________
Maintenance ....................................................................................................Section D
Safety Precautions ................................................................................................D-1
Periodic Maintenance .....................................................................................D-1,D-2
Control box ............................................................................................................D-2
Calibration Specification........................................................................................D-2
________________________________________________________________________
Wiring Diagram and Dimension Print............................................................Section F
________________________________________________________________________
Parts List...................................................................................................P-114 SERIES
________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
GENERAL INFORMATION
Advantages of the Spreadarc are:
PRODUCT DESCRIPTION
Arc length remains constant during oscillation to pro-
vide more uniform penetration.
General Physical Description
The K278-1 Spreadarc has been designed to oscillate
an Automatic welding head across the line of travel
when welding long seams. The welding head and noz-
zle are mounted to the Spreadarc carriage. The
Spreadarc is then mounted to either a stationary head
mount or travel carriage. The Spreadarc is compatible
with all Lincoln Electric welding heads including the
NA-3, NA-4, NA-5, and Power Feed-10S. The
Spreadarc is often used in conjunction with the TC-3
Travel Carriage and Vertical Lift Adjuster.
Dwell timers provide periods at the end-points of the
stroke for smoother bead edges.
The travel speed of the arc is uniform across the
bead.
RECOMMENDED PROCESSES AND
EQUIPMENT
General Functional Description
RECOMMENDED PROCESSES
The Spreadarc produces a linear oscillation of the
head and nozzle. A 24 VDC right-angle gear motor
drives the carriage onto which wire drive is mounted,
accommodating a 70-pound maximum load. The mov-
ing carriage is supported on a top and bottom "V"
track by four double row bearings, two on the top and
two on the bottom. The carriage motion is produced
by a pinion driving a rack that is mounted on the mov-
ing carriage support.
• The Spreadarc is compatible with all Lincoln Electric
welding heads including the NA-3, NA-4, NA-5, and
PF-10S.
• The Spreadarc can be used with submerged arc
(SAW), flux-cored (FCAW) and solid wire MIG
(GMAW) applications.
EQUIPMENT LIMITATIONS
Proximity switches control the length of travel. The
proximity switches remain stationary and stops mount-
ed to the moving carriage can be easily adjusted to
control travel distance. Both left and right extremes
are adjustable.
• The Spreadarc cannot be used with a K96 horizon-
tal head adjuster.
• The Spreadarc requires 42Vac input.
DESIGN FEATURES
The operator can set the oscillation travel speed and
dwell times at either end of the stroke to provide
smoother bead edges. Additionally, the Jog Mode
allows the operator to position the welding nozzle in
the correct starting location for a particular weld seam.
These values are set through a digital control panel on
the front of the machine.
• Compatible with NA-3, NA-4, NA-5, and PF-10S
Automatic Heads.
• Load capacity – 70 pounds.
• Oscillation Speed – 10-150 inches per minute.
• Dwell Time (Left/Right) – 0.0-4.0 seconds.
The oscillator uses bright digital displays and LED’s,
toggle switches, and heavy-duty push button designed
for every-day industrial use.
• Jog feature for positioning nozzle before welding
procedure begins.
• Rugged 24VDC Right-Angle gear motor.
• Bright, Digital Displays and LED’s.
• Heavy-duty push button.
• Proximity Sensors for adjustable sweep distance.
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
COMMON EQUIPMENT PACKAGES
BASIC PACKAGE
K1288-17
DC 600 Power Source
TC-3 Travel Carriage
NA-3 Control
K325S
K210-2
K212A
K231-1/8
K278-1
K1842-10
K29
NA-3N Head
Subarc Contact Nozzle
Spreadarc
Weld Cable
Vertical Lift Adjuster
Automatic Flux Hopper
K219
ADVANCED PACKAGE
Control Cable (10’ included with K278-1)
K1797-xx
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3
TECHNICAL SPECIFICATIONS
SPREADARC (K279-1)
INPUT VOLTAGE AND CURRENT
Voltage
Input Amperes
42/1/50/60
3.0
PHYSICAL DIMENSIONS
HEIGHT
13.7 in.
WIDTH
DEPTH
WEIGHT
65 lbs
17.8 in.
12.6 in.
(348 mm)
(452.12 mm)
(320.04 mm)
(29.5 kg)
ENVIRONMENTAL RANGES
Operating Temperature
Storage Temperature
-4°F to 104°F (-20°C to 40°C)
-40°F to 185°F (-40°C to 85°C)
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
A-1
INSTALLATION
• Dirt and dust that can be drawn into the Spreadarc
should be kept to a minimum. Failure to observe
these precautions can result in excessive operating
temperatures and nuisance shutdown.
NON-STANDARD SAFETY INFORMATION
WARNING
ELECTRIC SHOCK can kill.
MOUNTING
• Turn off power at the power source
disconnect switch before working
inside the equipment.
(See Figure A-1)
1. The Spreadarc can be mounted on a K325 travel
carriage or on a stationary head mount in which
case the work piece must be moved. When more
than one wire reel is used, the K325HC heavy duty
travel carriage is recommended. In many applica-
tions it may be desirable to use the K29 vertical lift
adjuster.
------------------------------------------------------------------------
WARNING
INPUT CONNECTIONS
• Only a qualified electrician should connect the
Spreadarc. Installation should be made in accor-
dance with the appropriate National Electrical
Code, all local codes and the information in this
manual.
------------------------------------------------------------------------
LOCATION
2. Remove the hex nut Item 1 and the support pin
Item 2 from the Spreadarc mounting block Item 3.
With the draw bolt Item 4 properly in place, mount
the Spreadarc to the head support or vertical lift
Item 5. Maintain support until the support pin Item
2 is inserted into the mounting block Item 3, and
install hex nut Item 1 and draw bolt Item 4. Rotate
the Spreadarc until it is perpendicular to the travel
carriage beam and tighten hex nut Item 1. Make
certain that the travel carriage beam or stationary
mount is properly squared up. The Spreadarc must
be level in the horizontal plane within 2°.
The Spreadarc will operate in harsh environments.
Even so, it is important that simple preventative mea-
sures are followed in order to assure long life and reli-
able operation.
• The Spreadarc must be located where there is free
circulation of clean air such that air movement in the
back, sides and bottom will not be restricted.
FIGURE A-1
5
2
4
3
1
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
A-2
INSTALLATION
3. Remove the head mounting block from the NA-3,
NA-4, NA-5, or POWER FEED-10S head (if includ-
ed) by removing the four allen head cap screws.
This part is not used during the installation of the
Spreadarc. Mount the head to the Spreadarc using
the two 1/2-13 X 1.00 hex head screws, washers
and lock washers supplied with the Spreadarc
through the two large holes in the head mounting
pad.(See Figure A-2)
The drive motor is to be in the vertical position and the
drive rolls are to face the front. Loosen the head face
plate clamp screw and rotate the face plate so that the
idle roll arm is down. Install the nozzle, wire straight-
ener and flux hopper (if used) per the NA-3, NA-4,
NA-5, or PF-10S operating manual.
When using the K225 Twinarc nozzle, a K219 flux
hopper and a standard head mounting on a travel car-
riage, and when welding from left to right, a special
12" flux tube is required. The tube, which is included
with the Spreadarc, may be trimmed to length to fit the
installation. In addition, it is necessary to re-position
the steel plate on the nozzle to which the flux hose
retainer ring is attached. Remove the two screws
holding this plate and rotate the plate 180° so the ring
is closer to the bottom of the nozzle. Replace the
screws.
Note: Before mounting an NA-5 or PF-10S head to
the Spreadarc, in order to assure clearance between
the motor connection box and the Spreadarc head
mounting surface, the motor mounting to the gearbox
should be rotated per the instructions below:
1. Remove the four screws mounting the gearbox
assembly to the motor adapter plate, and remove
gearbox.
HIGH FREQUENCY PROTECTION
2. Remove the three screws mounting the adapter
plate to the motor, rotate the adapter plate 90°
clockwise and replace the three mounting screws.
Locate the Spreadarc away from radio controlled
machinery. The normal operation of the Spreadarc
may adversely affect the operation of RF controlled
equipment, which may result in bodily injury or dam-
age to the equipment.
3. Remount the gearbox assembly with the four
mounting screws.
1/2-13 X 1.00
(2) HEX HEAD
SCREWS
FIGURE A-2
SPREADARC SHOWN WITH
THE POWER FEED-10S WIRE DRIVE
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
A-3
INSTALLATION
CONNECTION DIAGRAM
SEE FIGURE A-3
Connection to 42Vac Power Source
(See Figure A-3)
Required:
• 42Vac Power Source.
• K1797-xx Control Cable (10ft. included with K278-1).
• K278-1 Spreadarc.
K1797-XX
14 PIN
• NOTE: K1798 Terminal Strip Adapter may be nec-
essary if power source 14-pin connector is unavail-
able.
SEE FIGURE A-4
Connection to 115Vac Power Source
115V TO 42V
TRANSFORMER
KIT
Required:
(See Figure A-4)
K1797
• 115Vac Power Source.
• K1797-xx Control Cable (10ft.[3.05m] included with
K278-1).
• K1520-1 42 Volt Transformer Kit.
• K278-1 Spreadarc.
K1797-XX
Connection to 115Vac (direct)
SEE FIGURE A-5
Required:
(See Figure A-5)
115V TO 42V
TRANSFORMER
KIT
• K1797-xx Control Cable (10ft.[3.05m] included with
K278-1).
K1797
• K1520-1 42 Volt Transformer Kit (with customer
supplied input plug attached).
• K278-1 Spreadarc.
• Outlet plug not included.
K1797-XX
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
B-1
B-1
OPERATION
6. DIGITAL DISPLAY – Displays numerical settings
for each of the modes, such as Oscillation Speed in
inches per minute, Dwell Times in seconds, or Jog
Speed in inches per minute, under normal opera-
tion. Error codes are also displayed during fault
conditions.
CASE FRONT CONTROL DESCRIPTION
(See Figure B-1)
1. ON/OFF SWITCH – Turns power on/off to the unit.
2. START BUTTON – Starts the oscillation based on
the values set in each of the modes.
7. LED MODE INDICATORS – Illuminate to show the
active mode. When a mode is selected, the Display
will show the current value. This value can be
changed using the Adjust Switch in a stopped con-
dition or during active oscillation. Modes can be
selected while actively oscillating (real time).
3. STOP BUTTON – Stops oscillation.
4. JOG SWITCH – The Jog Switch will move the oscil-
lation carriage left or right at the speed set on the
Display. The speed can be pre-set before pressing
the Jog Switch left or right, or it can be changed
(real time) while jogging.
8. SELECT SWITCH – Used to select between the
available modes. When pressed up, the LED Mode
Indicators will scroll up the list. When pressed
down, the LED Mode Indicators will scroll down the
list. The Select Switch can be used in a stopped
state, or during active oscillation.
5. ADJUST SWITCH – The Adjust Switch is used to
change values stored in each mode. The Adjust
Switch can be used to set a value prior to starting
oscillation, or it can be used to change a mode
value (real time) while oscillating.
FIGURE B-1
6
7
8
5
4
1
2
3
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
B-2
OPERATION
SETTING REAR DWELL TIME
(See Figure B-4)
USER INTERFACE CONTROLS
SETTING OSCILLATION SPEED
Rear Dwell is the amount of time in seconds that oscil-
lation will stop at the LEFT proximity switch (when fac-
ing the Spreadarc Control Box) while welding contin-
ues. To adjust the Rear Dwell time, press the Select
Toggle Switch up or down until the LED for Rear
Dwell illuminates. The Display will show the current
value in seconds. To change the Rear Dwell time
value, press the Adjust Toggle Switch up or down to
raise or lower the Rear Dwell time value. When the
Start Button is pressed, the Spreadarc will "dwell" for
this amount of time when the proximity sensor is acti-
vated. The Rear Dwell can be changed before active
oscillation or while actively oscillating.
(See Figure B-2)
Oscillation Speed is the speed in inches per minute
that the Spreadarc carriage will travel back and forth.
To adjust the Oscillation Speed, press the Select
Toggle Switch up or down until the LED for Oscillation
Speed illuminates. The Display will show the current
value in inches per minute. To change the Oscillation
Speed value, press the Adjust Toggle Switch up or
down to raise or lower the Oscillation Speed value.
When the Start Button is pressed, the Spreadarc will
travel at this speed. The Oscillation speed can be
changed before active oscillation or while actively
oscillating.
FIGURE B-4
FIGURE B-2
JOG MODE
(See Figure B-5)
SETTING FRONT DWELL TIME
Jog is used while not actively oscillating in order to
move the carriage into a starting position. This fea-
ture is good for verifying what the Spreadarc will do
once oscillation is activated. To activate Jog, press
the Select Toggle Switch up or down until the LED for
Jog illuminates. The Display will show the current
value in inches per minute. To change the Jog speed
value, press the Adjust Toggle Switch up or down to
raise or lower the Jog speed value. The Jog feature
cannot be accessed during active oscillation.
(See Figure B-3)
Front Dwell is the amount of time in seconds that
oscillation will stop at the RIGHT proximity switch
(when facing the Spreadarc Control Box) while weld-
ing continues. This feature is used for good wash-in
of the weld metal with the wall of the work. To adjust
the Front Dwell time, press the Select Toggle Switch
up or down until the LED for Front Dwell illuminates.
The Display will show the current value in seconds.
To change the Front Dwell time value, press the
Adjust Toggle Switch up or down to raise or lower the
Front Dwell time value. When the Start Button is
pressed, the Spreadarc will "dwell" for this amount of
time when the proximity sensor is activated. The
Front Dwell can be changed before active oscillation
or while actively oscillating.
FIGURE B-5
FIGURE B-3
POWER -DOWN, POWER-UP SEQUENCE
At power-down, the Spreadarc will save all parame-
ters.
At power-up, the Spreadarc will return all parameters
and settings that were stored at last power-down.
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
B-3
B-3
OPERATION
COMMON WELDING PROCEDURES
Set the oscillation speed and the rear and front dwell
times as called for in the welding procedure. The front
dwell time controls the dwell when the nozzle is at the
proximity sensor farthest from the Spreadarc mount-
ing bracket (right-side when facing the Spreadarc
User Interface). The rear dwell time controls the dwell
when the nozzle is at the proximity sensor closest to
the Spreadarc mounting bracket (left-side when facing
the Spreadarc User Interface). The oscillation dis-
tance, or sweep length, is controlled by rotating either
or both of the proximity sensor stops as required giv-
ing proper front and rear electrode position. After the
desired oscillation track is obtained, lock the stops in
place by tightening the hex nuts against the stops.
In order to protect the Spreadarc from high tempera-
tures, best welding practices would be to set the travel
direction such that the unit moves away from the heat
of the arc, instead of over it.
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
D-1
MAINTENANCE
4. Provided the tracks are not severely worn, re-lubri-
cate the contact surface of the bearings and tracks
with a graphite or moly filled grease such as auto-
motive chassis grease and re-assemble.
NOTE: Do not lubricate the gear motor pinion
and gear rack.
SAFETY PRECAUTIONS
WARNING
ELECTRIC SHOCK can kill.
• Turn off power at the power source
disconnect switch before working
inside the equipment.
If the wear on the inside edge of the top rack has
reached 0.040", either interchange the top and bottom
tracks if the bottom track is not severely worn, or
replace both tracks.
-----------------------------------------------------------------------
PERIODIC MAINTENANCE
(See Figure D-1)
To remove the tracks:
"V" Tracks and Bearings
1. Loosen the 1/2-13 hex head screws Item 8 which
hold the bottom "V" bearings Item 6 in place by
rotating the screws while keeping the eccentric nuts
Item 9 from turning.
Clean, inspect, and re-lubricate twice per year (more
often under severe duty applications) as follows:
1. Remove the four screws Item 1 holding the proximi-
2. Rotate the eccentric nuts to give maximum clear-
ance of the bearings in relationship to the tracks.
ty sensor bracket Item 2 to the top cover Item 3.
2. Remove the four screws Item 4 holding the top and
bottom track covers Item 5 in place and remove the
track covers.
3. Lift the carriage to disengage the pinion gear from
the rack and remove. Set aside.
4. Remove the four screws Item 10 holding the control
box Item 11 in place. Maintain support for the con-
trol box in order not to strain any leads.
3. Clean the four "V" groove bearings Item 6 and the
top and bottom "V" tracks Item 7 and inspect for
wear.
FIGURE D-1
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
D-2
MAINTENANCE
5. With the control box and carriage out of the way,
access to the track fasteners Item 12 can be
gained.
CONTROL BOX
Every six months inspect the control box. If needed,
blow dirt out using low pressure air. Replace screw
holding door closed.
6. Inspect the four "V" bearings on the carriage to veri-
fy that they rotate freely and are not excessively
worn.
CALIBRATION SPECIFICATION
7. Note: Do not loosen the hex nuts holding the
gear motor in place – the gear motor has been
factory set to give proper clearance between the
rack and pinion
All calibration is factory set on the Spreadarc.
8. Remove the eight hex head screws Item 12 holding
the top and bottom tracks in place and remove the
tracks.
9. Install new tracks, or switch the tracks, on the track
support Item 13 ensuring that the tracks are seated
firmly on the edges of the track support.
10. Reassemble all parts except for the top and bot-
tom track shields and proximity sensor bracket.
11. To adjust the eccentric nuts on the bottom "V"
bearings, tighten the 1/2-13 screws until snug.
12. Rotate the eccentric nuts to bring the bottom bear-
ings snug against the track.
13. While holding the eccentric nuts securely, tighten
the 1/2-13 screws.
14. Verify proper pressure by turning outer race of
bottom bearings by hand. They must slip on
track, but there must be no vertical play in the
carriage assembly. Readjust eccentric nuts, if
necessary.
15. Lubricate tracks and bearings and install top and
bottom track shields and proximity sensor bracket.
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
F-1
F-1
WIRING DIAGRAMS
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
F-2
F-2
DIMENSION PRINT
SPREADARC
Download from Www.Somanuals.com. All Manuals Search And Download.
● Do not touch electrically live parts or
electrode with skin or wet clothing.
● Insulate yourself from work and
ground.
● Keep flammable materials away.
● Wear eye, ear and body protection.
WARNING
Spanish
● No toque las partes o los electrodos ● Mantenga el material combustible
● Protéjase los ojos, los oídos y el
bajo carga con la piel o ropa moja-
da.
● Aislese del trabajo y de la tierra.
fuera del área de trabajo.
cuerpo.
AVISO DE
PRECAUCION
French
● Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
● Gardez à l’écart de tout matériel
inflammable.
● Protégez vos yeux, vos oreilles et
votre corps.
ATTENTION
● Isolez-vous du travail et de la terre.
German
● Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
● Isolieren Sie sich von den
● Entfernen Sie brennbarres Material! ● Tragen Sie Augen-, Ohren- und Kör-
perschutz!
WARNUNG
Elektroden und dem Erdboden!
Portuguese
● Não toque partes elétricas e elec-
trodos com a pele ou roupa molha-
da.
● Mantenha inflamáveis bem guarda- ● Use proteção para a vista, ouvido e
dos.
corpo.
ATENÇÃO
● Isole-se da peça e terra.
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE
USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-
STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
● Keep your head out of fumes.
● Use ventilation or exhaust to
remove fumes from breathing zone.
● Turn power off before servicing.
● Do not operate with panel open or
guards off.
WARNING
Spanish
● Los humos fuera de la zona de res-
piración.
● Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
● Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
● No operar con panel abierto o
guardas quitadas.
AVISO DE
PRECAUCION
French
● Débranchez le courant avant l’entre- ● N’opérez pas avec les panneaux
tien.
● Gardez la tête à l’écart des fumées.
● Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
ouverts ou avec les dispositifs de
protection enlevés.
ATTENTION
German
● Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öff-
nen; Maschine anhalten!)
● Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
● Vermeiden Sie das Einatmen von
Schweibrauch!
● Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
WARNUNG
Portuguese
● Não opere com as tampas removidas.
● Desligue a corrente antes de fazer
serviço.
● Mantenha-se afastado das partes
moventes.
● Não opere com os paineis abertos
ou guardas removidas.
● Mantenha seu rosto da fumaça.
● Use ventilação e exhaustão para
remover fumo da zona respiratória.
ATENÇÃO
● Não toque as partes elétricas nuas.
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
Download from Www.Somanuals.com. All Manuals Search And Download.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|