RETURN TO MAIN MENU
SVM169-A
July, 2006
PRECISION TIG 185
For use with machines having Code Number : 11105 thru 11109
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
. . . and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before
you act and be careful.
SERVICE MANUAL
Copyright © 2006 Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
5.b. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
5.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
3.j. Also see Items 6.c. and 8.
5.e. Also see item 1.b.
Mar ‘95
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
iii
SAFETY
WELDING SPARKS can
cause fire or explosion.
CYLINDER may explode
if damaged.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
7.c. Cylinders should be located:
•Away from areas where they may be struck or subjected to
physical damage.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact can
cause overheating and create a fire hazard.
•A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
FOR ELECTRICALLY
powered equipment.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits.
This can create fire hazards or overheat lifting chains or
cables until they fail.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
6.h. Also see item 1.c.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Mar ‘95
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
iv
SAFETY
zones où l’on pique le laitier.
PRÉCAUTIONS DE SÛRETÉ
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
8. S’assurer que la masse est connectée le plus prés possible de
la zone de travail qu’il est pratique de le faire. Si on place la
masse sur la charpente de la construction ou d’autres endroits
éloignés de la zone de travail, on augmente le risque de voir
passer le courant de soudage par les chaines de levage,
câbles de grue, ou autres circuits. Cela peut provoquer des
risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher met-
allique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble de
soudage et la machine à souder en bon et sûr état defonc-
tionnement.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le total
de la tension à vide des deux machines.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSA Standard
W 117.2-1974.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie du
corps.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
3. Un coup d’arc peut être plus sévère qu’un coup de soliel, donc:
a. Utiliser un bon masque avec un verre filtrant approprié ainsi
qu’un verre blanc afin de se protéger les yeux du rayon-
nement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
b. Porter des vêtements convenables afin de protéger la peau
de soudeur et des aides contre le rayonnement de l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur place.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
RETURN TO MAIN MENU
MASTER TABLE OF CONTENTS FOR ALL SECTIONS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i-iv
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section A
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section B
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section C
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section D
Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section E
Troubleshooting and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section F
Electrical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section G
Parts Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P499 Series
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section A-1
Section A-1
TABLE OF CONTENTS
- INSTALLATION SECTION -
Installation ..............................................................................................................Section A
Technical Specifications.....................................................................................A-2/A-3
Safety Precautions ....................................................................................................A-4
Location.....................................................................................................................A-4
Grinding ..............................................................................................................A-4
Stacking..............................................................................................................A-4
Lifting and Moving..............................................................................................A-4
Tilting ..................................................................................................................A-4
Environmental Rating..........................................................................................A-4
Machine Grounding and High Frequency Interference Protection...........................A-4
Input Connections.....................................................................................................A-5
Input Reconnect Procedure......................................................................................A-6
Output Connections..................................................................................................A-6
Connections for TIG Welding .............................................................................A-6
TIG Torch Connection .................................................................................A-6
Work Cable Connection ..............................................................................A-7
Shielding Gas Connection...........................................................................A-7
Remote Control Connection........................................................................A-7
Connections for Stick Welding..................................................................................A-7
Stick Electrode Cable and Work Cable Connection ..........................................A-7
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
A-2
INSTALLATION
TECHNICAL SPECIFICATIONS - PRECISION TIG 185 (K2345-1AND K2347-1,-2)
INPUT - SINGLE PHASE ONLY
Standard Voltage
208/230/1/60
Input Current at Rated Output
35A / 32A Effective
and 70A / 64A Maximum
OUTPUT RANGE
Output Current
Maximum Open
Circuit Voltage
Type of Output
Range
7-185 Amps (AC)
5-185 Amps (DC)
(STICK AND TIG)
AC OCV: 75
DC OCV: 59
CC (Constant Current)
AC/DC
RATED OUTPUT
Duty Cycle
GTAW 15% Duty Cycle
100% Duty Cycle
Amps
185A AC/DC
90A AC/DC (BAL)
70A AC (AUTO-BAL)
Volts at Rated Amperes
15.2 V AC/DC
14.1 V AC/DC
13.8 V AC/DC
SMAW 15% Duty Cycle
100% Duty Cycle
185A AC/DC125
90A AC/DC
27.4 V AC/DC
23.6 V AC/DC
Chart gives max. rated Output Amps @% Duty Cycle (Based on a 10 minute cycle)
(Example; 110A@60% for AC/DC Stick and Balance TIG)
(1)
Usingstandard #8-3 inputcable for protected inputsupply
100%
90%
208/230v Model: AC/DC Stick & DC TIG
(AC TIG with #6-3 input cable)
460/575v Model: AC/DC Stick & AC/DC TIG
380/415v Model: AC/DC Stick &
DC/AC Auto-Bal.TIG
80%
70%
60%
50%
40%
30%
20%
10%
0%
208/230v Model: AC TIG using 230v input
380/415v Model: AC TIG (Max. Penetration)
208/230v Model: AC TIG using 208v input
50
70
90
110
130
150
170
190
OUTPUT AMPS
(1)
Wiring and protection based on the 2002 U.S. National Electric Code:
Use a Super Lag type fuse or circuit breaker with a delay in tripping action.
Models with NEMA 6-50P plug may be used with a 50 amp protected 6-50R receptacle, or
with a maximum 70 amp protected 6-50R receptacle if dedicated for the welder.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
A-3
INSTALLATION
TECHNICAL SPECIFICATIONS - CANADIAN (K2345-2), INTERNATIONAL K2346-1)
K2345-2 INPUT (at Rated Output)
Voltage/Phase/Freq.
460/575/1/60
Current
Idle Current
Power Factor
0.62 Min.
16 A/13 A Effective
32 A/26 A Max.
1.3 A/1.0 A Max.
K2346-1 INPUT (at Rated Output)
Voltage/Phase/Freq.
380/400-415/1/50/60
Current
Power Factor
0.62 Min.
Idle Current
19 A/18 A Effective
39 A/37 A Max.
1.3 A/1.0 A Max.
N80
OUTPUT RANGE
Max. OCV.
Weld Current
Output Type
74 V (AC)
59 V (DC)
7-185 A (AC)
5-185 A (DC).
CC (Constant Current)
AC or DC
RATED OUTPUT
Process Duty Cycle*.
Weld Current
Weld Voltage (NEMA)
SMAW
15%
100%
GTAW
15%
185 A AC/DC
90 A AC/DC
27.4 V
23.6 V
185 A AC/DC
90 A AC/DC (Auto-Bal.)
15.2 V
14.1 V
100%
* Based on a 10 minute cycle.
PHYSICAL DIMENSIONS(2)
MODEL
HEIGHT
WIDTH
DEPTH
WEIGHT
Machine Only
(K2345-1,-2)
(K2346-1)
20.71 in.
526 mm
14.48 in.
368 mm
Approx. 192 lbs.
87.1 kgs
25.62 in.
751 mm
Ready-Pak
(K2347-1)
20.71 in.
526 mm
14.48 in.
368 mm
Approx. 212lbs..
96.2 kgs.
25.62 in.
651 mm
Ready-PakW/Cart
(K2347-2)
31.24 in.
794 mm
19.81 in.
503 mm
Approx. 258lbs.
117.0 kgs.
38.01 in.
966 mm
(2)
Dimensions are without Lift Eyebolt and Torch Holder
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
A-4
INSTALLATION
SAFETY PRECAUTIONS
Read entire installation section before starting
installation.
WARNING
• Use only Lincoln provided
T4550-5 1/2-13 x 1.00 eyebolt.
• Fully engage threads and
torque eyebolt to 38 ft. lbs.
WARNING
• Re-torque eyebolt to 38 ft. lbs.
before each lift.
ELECTRIC SHOCK can kill.
• Only qualified personnel should
• Lift only with equipment of
adequate lifting capacity.
perform this installation.
• Turn the input power OFF at the
disconnect switch or fuse box
before working on this equipment.
FALLING
EQUIPMENT
cause injury.
• Never lift welder with gas
cylinder attached.
• Never lift welder above per-
sonnel.
• Do not touch electrically hot
parts.
• Lift only with equipment of adequate lifting
• Be sure machine is stable when lifting.
• Always connect the SQUARE WAVE TIG 175 PRO
to a power supply grounded per the National
Electrical Code and any local codes.
------------------------------------------------------------------------
---------------------------------------------------------------------------
An undercarriage, provided on the Ready-Pak w/Cart
model, is also available to easily move the the unit.
Refer to the Accessories section of this manual.
Do not attempt to lift the power source with an
undercarriage attached.
SELECT SUITABLE LOCATION
Place the welder where clean cooling air can freely cir-
culate in and out through the rear louvers. Dirt, dust or
any foreign material that can be drawn into the welder
should be kept at a minimum. Failure to observe these
precautions can result in excessive operating temper-
atures and nuisance shut-downs.
The undercarriage is designed for hand moving only;
mechanized movement can lead to personal injury
and/or damage to the Precision TIG 185.
GRINDING
TILTING
Each machine must be placed on a secure, level sur-
face, either directly or on a recommended undercar-
riage. The machine may topple over if this procedure is
not followed.
Do not direct grinding particles towards the welder. An
abundance of conductive material can cause mainte-
nance problems.
STACKING
ENVIRONMENTAL RATING
Square Wave TIG 185 cannot be stacked.
LIFTING AND MOVING
The PRECISION TIG 185 power source carries an
IP21 environmental rating. It may be used in normal
industrial and commercial environments. Avoid using it
in environments which have falling water such as rain.
The Precision TIG 185 models are provided with an
Eyebolt used for lifting the unit with a hoist. To install;
remove the plug button from the case top and screw
the Eyebolt securely into the threaded bracket
beneath the case top per the below instructions and
warnings provided on the case top decal. Save the
removed plug button (LE part No.T10397-2) to cover
the hole when the lift Eyebolt is removed.
Read and follow “Electric Shock Warnings” in the
Safety section if welding must be performed under
electrically hazardous conditions such as welding in
wet areas or on or in the workpiece.
MACHINE GROUNDING AND HIGH FRE-
QUENCY INTERFERENCE PROTECTION
This welder must be grounded! See your local and
national electrical codes for proper grounding
methods.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-5
A-5
INSTALLATION
6. Keep cover and all screws securely in place.
The high frequency generator, being similar to a radio
transmitter, may cause radio, TV and electronic equip-
ment interference problems. These problems may be
the result of radiated interference. Proper grounding
methods can reduce or eliminate radiated interference.
7. Electrical conductors within 50 ft (15.2m) of the
welder should be enclosed in grounded rigid metal-
lic conduit or equivalent shielding, wherever possi-
ble. Flexible metallic conduit is generally not suit-
able.
Radiated interference can develop in the following four
ways:
8. When the welder is enclosed in a metal building,the
metal building should be connected to several good
earth driven electrical grounds (as in 5 (b) above)
around the periphery of the building.
1. Direct interference radiated from the welder.
2. Direct interference radiated from the welding leads.
3. Direct interference radiated from feedback into the
power lines.
Failure to observe these recommended installation
procedures can cause radio or TV and electronic
equipment interference problems and result in unsatis-
factory welding performance resulting from lost high
frequency power.
4. Interference from re-radiation of “pickup” by
ungrounded metallic objects.
Keeping these contributing factors in mind, installing
equipment per the following instructions should mini-
mize problems.
INPUT CONNECTIONS
1. Keep the welder power supply lines as short as pos-
sible and enclose as much of them as possible in
rigid metallic conduit or equivalent shielding for a
distance of 50 feet (15.2m). There should be good
electrical contact between this conduit and the
welder case ground. Both ends of the conduit should
be connected to a driven ground and the entire
length should be continuous.
Be sure the voltage, phase, and frequency of the input
power is as specified on the rating plate, located on the
rear of the machine.
208/230 volt models have a NEMA 6-50P plug
attached to the #8-3 input power cord and a NEMA 6 -
50R receptacle is included with the Ready-Pak mod-
els. Other voltage models have an input power cord
but no plug or receptacle.
2. Keep the work and electrode leads as short as pos-
sible and as close together as possible. Lengths
should not exceed 25 ft (7.6m). Tape the leads
together when practical.
Have a qualified electrician provide input power supply
to the receptacle or cord in accordance with all local
and national electrical codes. Use a single phase line
or one phase of a two or three phase line. Choose an
input and grounding wire size according to local or
national codes. Refer to the Technical Specifications
page at the beginning of this section. Fuse the input
circuit with the recommended super lag fuses or delay
type1 circuit breakers. Using fuses or circuit breakers
smaller than recommended may result
3. Be sure the torch and work cable rubber coverings
are free of cuts and cracks that allow high frequen-
cy leakage.
4. Keep the torch in good repair and all connections
tight to reduce high frequency leakage.
5. The work piece must be connected to an earth
ground close to the work clamp, using one of the fol-
lowing methods:
in “nuisance” shut-offs from welder inrush currents
even if not welding at high currents.
1
Also called “inverse time” or “thermal/magnetic” circuit breakers;
a) A metal underground water pipe in direct contact
with the earth for ten feet or more.
circuit breakers which have a delay in tripping action that decreases
as the magnitude of the current increases.
b) A 3/4” (19mm) galvanized pipe or a 5/8”
(16mm)solid galvanized iron, steel or copper rod dri-
ven at least eight feet into the ground.
The ground should be securely made and the ground-
ing cable should be as short as possible using cable of
the same size as the work cable, or larger. Grounding
to the building frame electrical conduit or along pipe
system can result in re-radiation, effectively making
these members radiating antennas.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-6
A-6
INSTALLATION
INPUT RECONNECT PROCEDURE
INPUT LEADS
L1 & L2
On multiple input voltage welders, be sure the machine
is connected per the following instructions for the volt-
age being supplied to the welder.
LEAD H1
(DO NOT
REMOVE)
CAUTION
Failure to follow these instructions can cause immedi-
ate failure of components within the welder and void
machine’s warranty.
FOR LOWEST RATED VOLTAGE
: H2 CONNECTED
FOR HIGHEST RATED VOLTAGE
: H3 CONNECTED
-----------------------------------------------------------------------
Multiple voltage models are shipped connected for the
highest voltage. To change this connection refer to the
following instructions.
BACK VIEW OF LINE SWITCH
FIGURE A.1 Reconnect Leads
WARNING
ELECTRIC SHOCK can kill.
OUTPUT CONNECTIONS
• Turn the input power OFF at the dis-
connect switch or fuse box before
working on this equipment.
------------------------------------------------------------------------
For the lowest rated voltage connection (Refer to figure A.1):
1. Remove the sheet metal left side cover.
ELECTRODE/GAS
OUTLET
RECEPTACLE
(TWIST-MATE)
2. Disconnect lead H3 from the power switch and insu-
late with the insulation from the H2 lead.
3. Connect lead H2 to the power switch where H3 was
connected.
4. Tighten connections.
WORK CABLE & CLAMP
5. Replace sheet metal cover and all screws
For the highest rated voltage connection (Refer to figure A.1):
The machine is normally shipped connected for the
highest rated voltage, however verify the following:
FIGURE A.2 Location of Output Connections
1. Remove the sheet metal left side cover.
CONNECTIONS FOR TIG (GTAW) WELDING
2. Disconnect lead H2 from the power switch and insu-
late with the insulation from the H3 lead.
TIG TORCH CONNECTION
3. Connect lead H3 to the line switch where H2 was
connected.
Refer to Included Equipment in the Operation Section
of this manual for TIG welding equipment which is
included with the PRECISION TIG 185.
4. Tighten connections.
5. Replace sheet metal cover and all screws.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-7
A-7
INSTALLATION
A PTA-17 Twist-Mate TIG welding torch with cable and
connector is supplied with the Ready-Pak Models and
available for other models (See Accessories Section).
Turn the Power Switch “OFF”. Connect the torch cable
Twist-Mate quick connect plug into the Electrode/Gas
Output Receptacle on the front of the welder and turn
it clockwise until it is tight. This is a Twist-Mate quick
connect terminal and also provides the gas connection
for the shielding gas to the torch.
A cylinder is loaded by leaning it slightly sideways and
rocking it up on the platform, being careful not to allow
the Under-Storage Cart to roll. Secure the cylinder in
place with the provided chain. Unload by following
these steps in reverse.
REMOTE CONTROL CONNECTION
A remote control receptacle is provided on the case
front of the welder for connecting a remote control to to
the machine. A Foot Amptrol™, foot activated remote
control, is included with the PRECISION TIG 185
Ready-Pak models and available separately for other
models. Refer to the Optional Accessories section of
this manual for other available remote controls.
WARNING
To avoid receiving a high frequency shock, keep
the TIG torch and cables in good condition.
------------------------------------------------------------------------
WORK CABLE CONNECTION
CONNECTIONS FOR STICK (SMAW)
WELDING
A work cable with attached work clamp is factory con-
nected to the PRECISION TIG 185. To minimize high
frequency interference, refer to Machine Grounding
and High Frequency Interference Protection
section of this manual for the proper procedure on
grounding the work clamp and work piece.
STICK ELECTRODE CABLE AND WORK
CABLE CONNECTION
Refer to Field Installed Options in Accessories Section
of this manual for STICK welding equipment which is
available for use with the PRECISION TIG 185. An
electrode holder with Twist-Mate cable and Twist-Mate
connector are available separately for use with the
PRECISION TIG 185. (See Accessories Section).
Turn the Power Switch “OFF”. Connect the Twist-Mate
quick connect plug into the Electrode/Gas Output
Receptacle and turn it clockwise until it is tight. The
work cable and work clamp are factory connected.
SHIELDING GAS CONNECTION
An adjustable gas pressure regulator with flow gage
and hose is supplied with the PRECISION TIG 185
Ready-Pak Models and available separately for other
models (See Accessories Section). Obtain the neces-
sary inert shielding gas (usually argon). Connect the
cylinder of gas with the pressure regulator and flow
gage. Install the gas hose between the regulator and
gas inlet (located on the rear of the welder). The gas
inlet has a 5/16-18 right hand female thread;
CGA#032.
The available Under-Storage Cart features a low plat-
form that simplifies loading and unloading of gas cylin-
ders.
WARNING
CYLINDER could explode
if damaged.
• Keep cylinder upright and chained
to a support.
• Keep cylinder away from areas
where it could be damaged.
• Never allow the torch to touch the cylinder.
• Keep cylinder away from live electrical circuits.
• Maximum inlet pressure 150 psi.
------------------------------------------------------------------------
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A-8
A-8
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section B-1
Section B-1
TABLE OF CONTENTS
- OPERATION SECTION -
Operation ................................................................................................................Section B
Safety Precautions .......................................................................................................B-2
Graphic Symbols..........................................................................................................B-2
Product Description......................................................................................................B-3
Recommended Processes and Equipment..................................................................B-3
Welding Capability (duty cycle) ....................................................................................B-3
Controls and Settings...................................................................................................B-4
Control Functionality .............................................................................................B-4/B-5
Operating Steps ...........................................................................................................B-5
Welding in TIG Mode....................................................................................................B-5
Pulse TIG Control.........................................................................................................B-5
Remote Control Operation ...........................................................................................B-6
Benefits of the Precision TIG 185 Design ....................................................................B-6
Welding in Stick Mode .................................................................................................B-7
Recommended Electrode Amperage Ranges..............................................................B-7
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
B-2
OPERATION
GRAPHIC SYMBOLS THAT APPEAR ON
THIS MACHINE OR IN THIS MANUAL
SAFETY PRECAUTIONS
Read and understand this entire section before operat-
ing the machine.
INPUT POWER
WARNING
ELECTRIC SHOCK
can kill.
POSITIVE OUTPUT
NEGATIVE OUTPUT
•
Do not touch electrically live parts
or electrode with skin or wet cloth-
ing.
•
Insulate yourself from work and
ground.
• Always wear dry insulating gloves.
DIRECT CURRENT
•
Read and follow “Electric Shock Warnings” in the
Safety section if welding must be performed under
electrically hazardous conditions such as welding in
wet areas or on or in the workpiece.
PROTECTIVE
GROUND
--------------------------------------------------------------------------------
FUMES AND GASES
can be dangerous.
WARNING OR
CAUTION
• Keep your head out of fumes.
• Use ventilation or exhaust at the
arc, or both, to remove fumes and
gases from breathing zone and
general area.
DO NOT SWITCH
WHILE WELDING
------------------------------------------------------------------------
WELDING SPARKS can cause fire or
explosion
• Keep flammable material away.
• Do not weld on containers that
have held combustibles.
------------------------------------------------------------------------
ARC RAYS can burn.
• Wear eye, ear and body
protection.
------------------------------------------------------------------------
Observe additional Safety Guidelines detailed in
the beginning of this manual.
------------------------------------------------------------------------
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-3
B-3
OPERATION
RECOMMENDED EQUIPMENT/INTERFACE
(See Installed Options in Accessories Section for
more details)
PRODUCT DESCRIPTION
The Precision TIG 185 is a member of our field
acclaimed Precision TIG family of industrial arc weld -
ing power sources. Premium features include:
The Precision TIG 185 will be available as a basic
Machine (Only) and in two Factory-Configured Welding
Packages:
1. Precise constant current output.
2. Full range square wave AC/DC TIG (GTAW) weld--
ing.
1. Machine(Only) (K2345-1)
2. Ready-Pak (K2347-1)
3. Enhanced version of the patented Micro-
Start™Technology for its lower Minimum(5 amps) to
higher Maximum (185 amps) output control range.
4. Built-in high frequency stabilization for DC TIG start-
ing and continuous AC TIG welding.
5. AC/DC Stick (SMAW capability.) A new undercar-
riage (with gas bottle rack) is available for field
installation, or is included with an available Ready-
Pak TIG Welding Package. The Precision TIG
patented convenient built-in storage provisions for
welding components and cable management.
3. Ready-Pak w/Cart (K2347-2)
Basic module will also be available as with Domestic,
Canadian and International input voltages for user con-
figuration, with optional accessories.
Select Machine
208/230/1/60 Machine with 6 NEMA 6-50P
Plug Cable and Receptacle (K2345-1)
460/575/1/60 Machine only with cable (K2345-2)
380/400/415/1/50/60 Machine only
with cable (K2346-1)
Torch Starter Kit
(Select one)
Air Cooled System: Water Cooled System:
The Precision TIG 185 also provides advanced fea-
tures such as:
• Digital Meter
• Presettable control, adjustable Auto Balance™
• Fan As Needed (F.A.N.)
• Timers for fixed Preflow and variable Postflow shield-
ing gas.
• Built-in, easy to set single knob Pulse TIG control with
a "blinking" light to indicate the pulse frequency set-
ting.
• Auto-Sense remote control selection.
• Tool-less Twist-Mate electrode cable connection.
• Built-in work clamp cable permanently attached.
TIG-Mate
TIG-Mate 20
Torch Starter Kit*
Not Applicable
Torch Starter Kit*
115V 50/60Hz
Cool-Arc 40*
Water Cooler
Under-Storage
Cart (Optional )
Optional Remote
Trigger Device
(Select one)
K2348-(*)
Arc Start Switch*
Foot Amptrol*
Start Pedal Foot Amptrol*
Hand Amptrol*
*For “Part Numbers” or “K Numbers” see Accessories Section.
EQUIPMENT LIMITATIONS
The Precision TIG machines are protected from over
loads beyond the output ratings and duty cycles, per
the Specifications in the Installation Section, with
Thermostat protection of the output power coils and
rectifiers.
Four models are available for 60Hz. with Domestic and
Canadian input voltages, as well as an International
model with 50/60Hz voltages.
The PRECISION TIG 185 machine uses Twist-Mate
output terminals, therefore stud connection adapters
(such as LECO. S19257-series) cannot be used for
torch connection.
RECOMMENDED PROCESSES AND
EQUIPMENT
RECOMMENDED PROCESSES
If a Precision Tig 185 is powered from an engine gen-
erator which doesn’t have sufficient capacity, the AC
Balance control and the Output control will not provide
full range of control.
The Precision TIG 185 is recommended for the TIG
(GTAW) and Stick (SMAW) welding processes within
its output capacity range of 5 amps DC,or 7 amps AC,
to 185 amps AC/DC. It is compatible with most
Magnum TIG accessories, as well as many industry
standard items, such as TIG torches (adapted for
Twist-Mate), hoses, and water coolers.
WELDING CAPABILITY(Duty Cycle)
The PRECISION TIG 185 is rated at 185 amps, 27
volts, at 15% duty cycle on a ten minute basis. It is
capable of higher duty cycles at lower output currents.
See rated output graph, on specification sheet located
in the Installation Section. If the duty cycle is exceed-
ed, a thermal protector will shut off the output until the
machine cools.
PROCESS LIMITATIONS
The Precision TIG machines are not recommended for
arc gouging due to it's limited output capacity, and are
also not recommended for pipe thawing.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-4
B-4
OPERATION
CONTROLS AND SETTINGS
All operator controls and adjustments are located on the front of the PRECISION TIG 185. Refer to Figure B.1
and corresponding explanations.
FIGURE B.1 - CONTROL PANEL
1. POWER SWITCH
2. POLARITY SWITCH
3. MODE SWITCH
13
9
5
4. AC BALANCE CONTROL
5. MAXIMUM OUTPUT CONTROL (AMPS)
6. DIGITAL METERS
3
7. POST FLOW TIME
8. PULSE TIG CONTROL
9. THERMAL SHUTDOWN LIGHT
10. REMOTE RECEPTACLE
11. ELECTRODE/GAS OUTPUT
RECEPTACLE
4
12. WORK CABLE
13. REMOVABLE LIFT EYEBOLT
6
7
8
1
2
11
12
10
• Auto Balance position indicated by the Green panel
light turning on.
CONTROL FUNCTIONALITY
This setting position feature automatically provides the
proper amount of cleaning and penetration for normal
AC TIG welding.
1. POWER SWITCH – Input line switch turns input
power ON or OFF, as indicated by the on or off sta-
tus of the front panel digital display (See Item 6).
5. MAXIMUM OUTPUT CONTROL – Presets the out-
put welding current over the rated output range of
the machine:
2. POLARITY SWITCH – The rotary power switch has
3-positions for DC+, AC and DC- selections for the
electrode output stud welding polarity.
• With a Remote Current Control (Amptrol) connect-
ed to the Remote Receptacle (See item 10), this
knob sets the Maximum output current level set
table with the remote Amptrol.
• For Pulse TIG (See Item 8) this knob sets the Peak
Pulse level, with the Remote Amptrol (if used).
CAUTION
• Do not switch the polarity switch
while welding or damage may result
to the machine.
6. DIGITAL METER – A 3 digit LED meter is used to
display the preset output current level before weld-
ing, and actual output level while welding:
• A lit display indicates input power is turned on.
(See Item 1.)
------------------------------------------------------------------------
3. MODE SWITCH – The push button switch allows
selection of the two machine welding modes as indi-
cated by colored mode lights:
• STICK mode – Top position Red light.
• TIG mode – Bottom position Green light.
4. AC BALANCE CONTROL – The AC Balance
Control permits adjustment of the AC TIG wave bal-
ance adjustment from Max. Penetration (80% nega-
tive wave) at full CW rotation setting, to Max.
Cleaning (60% positive wave) at CCW rotation, and
includes:
7. POST FLOW TIME – Sets the TIG mode shielding
gas post flow time over the range of about 1 to 30
seconds after the arc is shut off.
Note: Gas preflow time is fixed at 0.5 second only in
TIG mode, but no preflow time will occur if the arc is
restarted during Post Flow time, since shielding gas
would not have stopped flowing.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-5
B-5
OPERATION
8. PULSE TIG CONTROL – The Pulse TIG feature
built into the Precision TIG 185 is simplified to be a
single knob control which sets the Pulse Frequency
over the peak pulses/sec. range of about 0.1 to 20
pulses per second:
OPERATING STEPS
WELDING IN TIG MODE
1. Connect the TIG torch and cable Twist-Mate quick
connect plug to the Electrode/Gas output recepta-
cle. This receptacle also contains an integral gas
connection for the torch. Connect the work clamp to
the work piece.
• Full CCW (min.) setting of the control knob shuts
off Pulse TIG (0.0 pps).
• Peak Pulse level is set by the Max. Output Control
and the Remote Amptrol (if used).
• Background Current level is typically optimized at
a fixed 50% of Peak Pulse level setting.
• Peak Pulse % On-time is typically optimized at a
fixed50%.
2. Set the TIG/STICK switch to “TIG”.
3. Set the Polarity Switch to DC- for welding steel or
stainless steel; or to AC for welding aluminum.
A Green light "blinks" with each Peak Pulse to indi-
cate the Pulse TIG Control setting before and during
welding.
4. Connect the Foot Amptrol to the Remote Control
Connector.
9. OVER TEMPERATURE LIGHT -
If the welder
5. Turn on the cylinder gas valve and adjust the flow
regulator to obtain desired flow.
overheats due to blocked air flow, high ambient air
temperature, or exceeded duty cycle, an internal
thermostat will open disabling the welding output
and this yellow light will illuminate. The cooling fans
will continue to run to cool the unit during this time.
The light will go out when the unit cools and the
thermostat resets. Once the light goes out, the
machine will again become available to weld.
6. Turn the power switch to “ON”. NOTE: There will be
a 15 second gas flow when the power is turned on.
7. Preset the Output Control on the control panel to the
maximum desired amps, as read on the digital
meter.
10. REMOTE RECEPTACLE – Provides for connec-
tion of remote control and/or arc start switch only in
TIG Mode: ( There is no remote output control
capability when stick welding.
8. Depress the Foot Amptrol to energize the torch and
establish an an arc with the work piece. The digital
meter reads the actual amps while welding.
• Plugging a remote current control (Amptrol) into
this receptacle automatically switches the output
control from the panel Max Output Control (See
Item 5) to the remote control.
• The connected remote control will then control the
output current between the Min. range of the
machine and the setting of the panel Max Output
Control.
• Switching Mode Switch (See Item 3) to Stick will
automatically disable the connected remote con-
trol and switch the output control back to the Max
Output panel control.
NOTE: When the TIG/STICK switch is set to “TIG”,
depressing the remote control will start a 0.5 second
gas pre-flow before energizing the TIG torch. When the
remote control is released the TIG torch is de-ener-
gized and gas flow will continue for the time set by the
Post Flow Time control. When the polarity switch is set
to DC, the TIG Arc Starter will turn on and off automat-
ically to start and stabilize the arc. In AC the TIG Arc
Starter will turn on with the output and remain on con-
tinuously until the remote control is released.
PULSE TIG CONTROL
11. ELECTRODE/GAS OUTPUT RECEPTACLE -
This quick connect Twist-Mate receptacle provides
electrical connection to the electrode holder and
cable for Stick welding and a combined electrical
and gas connection for the TIG torch when TIG
welding.
Use this knob to set the frequency or the number of
pulses per second(pps), from 0.1pps to 20pps.
• This setting adjusts heat output and bead shape for
travel speed. Thinner plate that is welded with faster
travel speed will require higher frequency than thick-
er plate with slower travel speed. 2-3pps is a typical
starting point.
12. WORK CABLE - This work cable is factory con-
nected to the welder and is connected to the work
piece to complete the welding circuit. Refer to
Machine Grounding and High Frequency
Interference Protection in the Installation section
of this manual for the proper procedure on ground-
ing the work clamp and work piece to minimize
high frequency interference.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-6
B-6
BENEFITS OF THE PRECISION TIG 185 DESIGN
OPERATION
REMOTE CONTROL OPERATION
A Foot Amptrol ™is included with the PRECISION TIG
185 Ready-Pak models and availiable for other models
(See Accessories Section) for remote current control
while TIG welding. An optional Hand Amptrol may also
be used. An optional Arc Start Switch may be used to
start and stop the welding if no remote control of the
current is desired. Refer to the Accessories Section of
this manual.
In AC TIG welding of aluminum, the positive portion of
the AC wave provides cleaning (removal of aluminum
oxide) of the work piece. This is desirable on materials
with a heavy oxide coating. However the positive por-
tion may also cause the electrode to overheat at high
currents causing “tungsten spitting”. The negative por-
tion of the AC wave offers no cleaning action but con-
centrates more heat on the work.
Both the Hand and Foot Amptrol work in a similar man-
ner. For simplicity, the following explanation will refer
only to “Amptrols”, meaning both Foot and Hand mod-
els. The term “minimum” refers to a foot pedal in the
“up” position, as it would be with no foot pressure, or a
Hand Amptrol in the relaxed position, with no thumb
pressure.
The AC waveform of the PRECISION TIG 185 opti-
mizes cleaning and heating of the work. The result is
the capability to weld through the complete range in AC
TIG or DC- TIG requiring only one electrode, a 3/32”
2% thoriated tungsten.
“Maximum” refers to a fully depressed Foot Amptrol,or
a fully extended Hand Amptrol.
When the welder is in TIG modes activating the
Amptrol energizes the electrode terminal and varies
the output welding current from its minimum value of 5
Amp (DC) or 7 Amp (AC), to the maximum value set by
the Current Control on the control panel. This helps
eliminate accidental high current damage to the work
piece and/or tungsten, and provides a fine control of
the current. When the welder is in the stick mode a
remote control has no effect and is not used.
It is important to note that, in some cases, the tungsten
will not start an arc at the minimum current because
the tungsten may be too large or cold. To start an arc
reliably, it is important to depress the Amptrol far
enough so that the machine output current is near the
tungsten operating range. For example, a 3/32” tung-
sten may be used on DC- to weld over the full range of
the machine.
To start the arc, the operator may have to turn the cur-
rent control up and depress the Amptrol approximately
1/4 of the way down. Depressing the Amptrol to its min-
imum position may not start the arc. Also if the current
control is set too low, the arc may not start. In most
cases, a large or cold tungsten will not readily establish
an arc at low currents. This is normal. In Direct Current
mode the PRECISION TIG 185 will start a 3/32”, 2%
thoriated tungsten electrode at 15 amperes provided
the electrode tip is properly grounded and not contam-
inated.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-7
B-7
OPERATION
WELDING IN STICK MODE
5. Turn the power switch to “ON”.
6. Adjust the Current Control to the desired amps.
7. Strike an arc and weld.
1. Put the electrode holder and cable quick connect
plug into the electrode output receptacle. Turn clock-
wise until tight. Connect the work clamp to the work
piece.
NOTE: When the TIG/STICK switch is set to “STICK”
the output is always on when the power switch is on. A
remote control has no effect on the welding current and
the gas flow and high frequency TIG arc starter are dis-
abled.
2. Set the TIG/STICK switch to “STICK”.
3. Set the Polarity Switch to the weld mode desired for
the type of electrode being used (most commonly
DC+).
4. Place the electrode in the electrode holder.
WARNING
• In Stick Mode the output terminal
and electrode will be electrically hot
whenever the power switch is turned
on.
-----------------------------------------------------------------------
RECOMMENDED ELECTRODE AMPERAGE RANGES - PRECISION TIG 185
The PRECISION TIG 185 is rated from 5-185 Amps.
SMAW Process
Welding Amp Range for Stick Electrode Size
ELECTRODE TYPE
Fleetweld 5P, Fleetweld 5P+ E6010
Fleetweld 180
Fleetweld 37
Fleetweld 47
POLARITY
DC+
3/32"
40 - 70
40 - 80
70 - 95
75 - 95
85 - 110
40 - 80
40 - 70
1/8"
5/32"
75 - 130
55 - 110
100 - 135
100 - 145
110 - 160
75 - 110
60 - 100
90 - 175
105 - 135
145 - 180
135 - 200
130 - 200
95 - 150
90 - 140
E6011
E6013
E7014
E7018
DC+
DC+
DC-
DC+
DC+
DC+
Excalibur
Blue Max Stainless
Red Baron Stainless
Mild steel procedures are based on recommended procedures listed in C2.10 8/94 and the maximum rating of the PRECISION TIG 185
Blue Max procedures are based on C6.1 6/95
Red Baron Procedure are based on ES-503 10/93
GTAW Process
Electrode Polarity
Electrode Tip Preparation
DC-
Sharpened
AC
Balled
Approximate Argon
Gas Flow Rate
C.F.H. (l/min.)
EWZr
Electrode Type
EWTh-1, EWCe-2
EWTh-2, EWLa-1
EWG
Up to 15 A.
Up to 15 A.
Up to 80 A.
Up to 150 A.
Up to MAX. A.
X
EWTh-1, EWTh-2
EWCe-2, EWLa-1
EWG
EWP
Stainless
Steel
(2-4) 3-8 (2-4)
Tungsten Size (in.)
Aluminum
3-8
.010
.020
.040
1/16
3/32
1/8
Up to 10 A.
Up to 15 A.
Up to 40 A.
Up to 15 A.
Up to 20 A.
Up to 60 A.
Up to 130 A.
Up to MAX. A.
X
5-10
5-10
5-10
(3-5) 5-10 (3-5)
(3-5) 5-10 (3-5)
(3-5) 9-13 (4-6)
Up to 100 A.
Up to 160 A.
Up to MAX. A.
13-17 (6-8) 11-15 (5-7)
15-23 (7-11) 11-15 (5-7)
Tungsten electrodes are classified as follows by the American Welding Society (AWS):
Pure..................................EWP........green
+1% Thoria .......................EWTh-1...yellow
+2% Thoria .......................EWTh-2...red
+2% Ceria.........................EWCe-2...orange
+1.5% Lanthana ...............EWLa-1...black
+0.15 to 0.40% Zirconia....EWZr.......brown
TRI-MIX OF ELEMENTS.............EWG.........gray
Ceriated Tungsten is now widely accepted as a substitute for 2% Thoriated Tungsten in AC and DC applications.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
B-8
B-8
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section C-1
Section C-1
TABLE OF CONTENTS
- ACCESSORIES SECTION -
Accessories ............................................................................................................Section C
Options / Accessories...........................................................................................C-2/C-3
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2
C-2
ACCESSORIES
FACTORY INSTALLED OPTIONS
2. Precision TIG 185 Ready-Pak w/Cart (K2347-2)
The Precision TIG 185 will be available in two Factory-
Configured Welding Packages:
• 208/230/1/60 Machine (K2345-1)
• 9 ft.(2.7m) Input Cable with NEMA 6-50P Plug*
• NEMA 6-50R Receptacle
1. Precision TIG 185 Ready-Pak (K2347-1)
• Integrated 10 ft.(3.1m) Work Lead w/Clamp*
• Gas Regulator with 10 ft.(3.1m) Hose
• 208/230/1/60 Machine (K2345-1)
• 9 ft. (2.7m) Input Cable with NEMA 6-50P Plug*
• NEMA 6-50R Receptacle
• PTA-17 12.5 ft.(3.8m) One cable Superflex Torch with
3/32”(2.4mm) Electrode and Parts
• Foot Amptrol (K870)
• Integrated 10 ft.(3.1m)Work Lead w/Clamp*
• Gas Regulator with 10 ft.(3.1m). Hose
• PTA-17 12.5”(318mm) Ultra=Flex Torch with
3/32”(2.4mm)Electrode and Parts
• Foot Amptrol (K870)
• TIG Slide Rule (WC332)*
• GTAW Book (JFLF-834)*
• Lift Eyebolt*
• Under-Storage Cart (K2348-1)
• TIG Slide Rule ( WC332)*
* Included with K2345-1 Machine Only model.
• GTAW Book (JFLF-834)*
• Lift Eyebolt*
The Precision TIG 185 will also be available as Basic
models with Domestic input voltages for user-configu-
ration with optional accessories: (See Table C.1)
TABLE C.1
208/230/1/60 Machine with 9 ft.(2.7m) NEMA 6-50P Plug Cable and Receptacle (K2345-1)
460/575/1/60 Machine only with Cable (K2345-2)
Select Machine
380/400-415/1/50-60 Machine only with Cable (K2346-1)
Water Cooled System
Air Cooled System
Optional
Torch Starter Kit
(Select one)
K2267-1 TIG-Mate 20 Torch Starter Kit
Includes:
K2266-1 TIG-Mate Torch Starter
Kit Includes:
• 200A PTW-20 12.5 ft.(3.81m) Torch
• KP510 Parts Kit
• 150A PTA-17 12.5 ft.(3.81m) Torch.
• KP508 Parts Kit.
• Regulator & Hose
• Regulator & Hose.
• K1622-4 Twist Mate Torch Adapter
• Water Hose & Hose Coupler
• Work Cable & Clamp (Not required for
Precision TIG 185)
• K1622-1 Twist Mate Torch Adapter.
• Work Cable & Clamp (Not required for Precision
TIG 185)
Not Applicable
K1813-1 115V 50/60Hz Cool-Arc 40
Water Cooler
Optional Under-
Storage Cart
K2348-1
K814 Arc Start Switch
K870 Foot Amptrol
K870-1 Start Pedal Foot Amptrol
K963-3 Hand Amptrol
Optional Remote
Trigger Device
(Select one)
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
C-3
C-3
ACCESSORIES
FIELD INSTALLED OPTIONS
• Magnum “Pro-Torch™ TIG Torch” assemblies and
Accessories.
The following Options/Accessories are available for the
Precision TIG 185:
Requires Twist-Mate Adapter:
K1622-1 for PTA-9/-17
K1622-3 for PTA-26
• K2348-1 Under-Storage Cart
K1622-4 for PTW water cooled torch
Includes a front magnetic latch storage drawer and
rear storage bin on a single bottle undercarriage.
(L12225 Installation Instructions included)
• Harris #3100211 Harris Argon Flow Regulator
(Includes 10 ft.(3.1m) hose.)
• K870 Foot Amptrol
Single pedal foot activation of arc start switch and
output control, with 25 ft.(7.6m) plug cable.
• K2374-1 Electrode Holder and Cable
200 amp Electrode Holder with 10 ft.(3.1m) cable
and Twist-Mate connector.
• K870-1 Start Pedal Foot Amptrol
Independent start pedal on control pedal provides
two-stage foot action to easily feel start switch clo-
sure at minimum output level for enhanced arc start
and crater-fill control. Provided with adjustable, or
removable , heel stop and 25 ft.(7.6m) plug cable.
• K963-3 Hand Amptrol
Fastens to torch for convenient thumb activation of
arc start switch and output control, with 25 ft.(7.6m)
plug cable:
• K814 Arc Start Switch
Needed for TIG welding without an Amptrol. Includes
25 ft.(7.6m) plug cable, and attaches to torch for
convenient finger control.
• TIG-Mate Torch Starter Kits:
Includes Torch with Twist-Mate adapter and acces-
sories listed below:
K2266-1 TIG-Mate Torch Starter Kit Includes:
• 150A PTA-17 12.5 ft.(3.8m) Torch
• KP508 Parts Kit
• Regulator & Hose
• K1622-1 Twist Mate Torch Adapter
• Work Cable & Clamp (Not required for Precision
TIG 185)
K2267-1 TIG-Mate 20 Torch Starter Kit Includes:
• 200A PTW-20 12.5 ft.(3.8m) Torch
• KP510 Parts Kit
• Regulator & Hose
• K1622-4 Twist Mate Torch Adapter
• Water Hose & Hose Coupler
• Work Cable & Clamp
(Not required for Precision TIG 185)
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
C-4
C-4
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section D-1
Section D-1
TABLE OF CONTENTS
- MAINTENANCE SECTION -
Maintenance...........................................................................................................Section D
Safety Precautions ........................................................................................................D-2
Routine Maintenance.....................................................................................................D-2
Periodic Maintenance....................................................................................................D-2
Spark Gap Adjustment..................................................................................................D-2
Fan Motor and Blade Replacement ..............................................................................D-2
Major Component Locations.........................................................................................D-3
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
D-2
MAINTENANCE
WARNING
SAFETY PRECAUTIONS
WARNING
Use extreme caution when working with circuit of
the high frequency. The high voltages developed
can be lethal. Turn the input power off using the
disconnect switch or fuse box before working
inside machine. This is particularly important when
working on the secondary circuit of the high volt-
age transformer (T3) because the output voltage is
dangerously high.
-----------------------------------------------------------------------
Refer to figure D.1. Note in highly dirty environments
where there is an abundance of conductive contami-
nants, use a low pressure air stream or a firm piece of
paper to clean the spark gap. Do not disturb the facto-
ry setting.
ELECTRIC SHOCK can kill.
• Only qualified personnel should per-
form this maintenance.
• Turn the input power OFF at the dis-
connect switch or fuse box before
working on this equipment.
• Do not touch electrically hot parts.
------------------------------------------------------------------------
WARNING
To check the spark gap:
- Turn off input power as specified above.
- Remove the right side panel from the
machine, the spark gap box is located on the
lower right side.
To avoid receiving a high frequency shock, keep
the TIG torch and cables in good condition.
------------------------------------------------------------------------
- Check the spark gap with a feeler gauge.
If adjustment is needed:
ROUTINE AND PERIODIC MAINTENANCE
- Adjust the gap by loosening the allen head
screw in one of the aluminum blocks, near
the front of the unit and tighten the screw in
the new position.
1. Disconnect power supply lines to machine before
performing periodic maintenance.
If the gap is correct:
2. Periodically clean the inside of the machine with a
low pressure air system. Be sure to clean the fol-
lowing components thoroughly.
• Main Transformer
- Replace the wraparound.
8. Inspect gas hose and inlet fitting for cracks or leaks.
9. Replace any unreadable labels or decals.
• Electrode/Gas Output Receptacle
• Polarity Switch
• Rectifier Assembly
• Arc Starter/Spark Gap Assembly
• PC Boards
10. Verify that the machine and welding circuit is prop-
erly grounded.
FIGURE D.1 SPARK GAP
• Fan Blades
3. Inspect welder output and control cables for fraying,
cuts, and bare spots.
.020 Spark Gap
4. Keep TIG torch and cables in good condition.
5. Clean air louvers to ensure proper air flow and cool-
ing.
FAN MOTOR OR FAN BLADE REPLACEMENT
When installing a new fan blade or fan motor be sure
to maintain proper shaft spacing per Figure D.2 below.
6. The fan motor has sealed ball bearings which
require no maintenance.
7. SPARK GAP ADJUSTMENT
The spark gap is set at the factory to a gap of 0.020
See Figure D.1. This setting is adequate for most
applications. Where less high frequency is desired,
the setting can be reduced to 0.015 inches (0.4mm).
.30
FIGURE D.2
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
D-3
D-3
MAINTENANCE
FIGURE D.2 — LOCATION OF MAINTENANCE COMPONENTS.
1. Case Front Assembly
2. Case Back Assembly
3. Arc Starter & Bypass Assembly
4. Center Assembly
5. Cover Assembly
6. Cart Base Assembly
7. Upper Cylinder Support Assembly
8. TIG Torch & Cable Assembly
9. Foot Amptrol Assembly (Pedal)
7
5
2
4
1
9
3
8
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
D-4
D-4
NOTES
X
Download from Www.Somanuals.com. All Manuals Search And Download.
Section E-1
Section E-1
TABLE OF CONTENTS
- THEORY OF OPERATION SECTION -
Theory of Operation...............................................................................................Section E
General Description ......................................................................................................E-2
Input Power Circuit.......................................................................................................E-2
Output Rectification and Feedback Control.................................................................E-3
High Voltage/High Frequency Circuit ...........................................................................E-4
DC Welding Output.......................................................................................................E-5
AC Welding Output.......................................................................................................E-6
SCR Operation..............................................................................................................E-7
Protective Circuits.........................................................................................................E-8
Thermal Protection .......................................................................................................E-8
Overload Protection......................................................................................................E-8
FIGURE E.1 – PRECISION TIG 185 BLOCK LOGIC DIAGRAM
BY-PASS
BOARD
WORK
POLARITY
SWITCH
ELECTRODE
HI-FREQUENCY
TRANSFORMER
MAIN
TRANSFORMER
INPUT
POWER
SWITCH
BYPASS
ASBLY
C
H
O
K
E
H1
AC
SCR
BRIDGE
DC+
X1
X2
H2
H3
HIGH VOLTAGE
TRANSFORMER
CIRCUIT
SHUNT
DC-
AC
F
E
E
D
B
A
C
K
115VAC
18VAC
18VAC
CONTROL
BOARD
POWER
"ON"
DIGITAL
115VAC
FAN
DISPLAY
MODE
SWITCH
REMOTE
RECEPTACLE
THERMO-
STATS
THERMAL
LIGHT
GAS
VALVE
OUTPUT
CONTROL
AC
BALANCE
CONTROL
AUTO
BALANCE
LED
PULSE
FREQ.
LED
STICK
LED
TIG
LED
POSTFLOW
CONTROL
PULSE
CONTROL
X
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2
E-2
TM
THEORY OF OPERATION
GENERAL DESCRIPTION
3. Enhanced version of the patented MicroStart
Technology for its lower Minimum (5amps) to high-
The PRECISION TIG 185 is a member of our field
acclaimed Precision TIG family of industrial arc weld-
ing power sources. Premium features include:
er Maximum (185 amps) output control range.
4. Built-in high frequency stabilization for DC TIG
starting and continuous AC TIG welding.
1. Precise constant current output.
2. Full range square wave AC/DC TIG (GTAW) weld-
ing.
5. AC/DC Stick (SMAW capability.)
FIGURE E.2 Main Transformer and Input Power
BY-PASS
BOARD
WORK
POLARITY
SWITCH
ELECTRODE
HI-FREQUENCY
TRANSFORMER
MAIN
TRANSFORMER
INPUT
POWER
SWITCH
BYPASS
C
H
O
K
E
ASBLY
H1
AC
SCR
BRIDGE
DC+
X1
H2
HIGH VOLTAGE
TRANSFORMER
CIRCUIT
SHUNT
X2
DC-
AC
H3
F
E
E
D
B
A
C
K
115VAC
18VAC
18VAC
CONTROL
BOARD
POWER
"ON"
115VAC
FAN
DIGITAL
DISPLAY
MODE
SWITCH
REMOTE
RECEPTACLE
THERMO-
STATS
THERMAL
LIGHT
GAS
VALVE
OUTPUT
CONTROL
AC
BALANCE
CONTROL
AUTO
BALANCE
LED
PULSE
FREQ.
LED
STICK
LED
TIG
LED
POSTFLOW
CONTROL
PULSE
CONTROL
incorporated in the main transformer. The 115VAC
winding supplies power to the fan motor and also,
through the control board, powers the gas solenoid
valve and the high voltage transformer. The 18VAC
winding provides power to the trigger circuitry. The
other 18VAC winding is rectified and regulated to a
15VDC supply which operates the circuitry on the con-
trol board.
INPUT POWER CIRCUIT
The desired single-phase input power is connected to
the TIG 185 through an input power switch located in
the front panel of the machine. The machine can be
configured for either 230VAC or 208VAC input voltage
by connecting the appropriate lead (H2 or H3) to the
input power switch. When the input power switch is
turned “ON” the input voltage is applied directly to the
primary of the main transformer.
The main transformer changes the high voltage, low
current input power to a low voltage, high current out-
put which is available at the main secondary winding
(X1 and X2). In addition three auxiliary windings are
NOTE: Unshaded areas of block logic diagrams are the subject of discussion.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-3
E-3
THEORY OF OPERATION
FIGURE E.3 Control Board and Output Feedback Control.
BY-PASS
BOARD
WORK
POLARITY
SWITCH
ELECTRODE
HI-FREQUENCY
TRANSFORMER
MAIN
TRANSFORMER
INPUT
POWER
SWITCH
BYPASS
ASBLY
C
H
O
K
E
H1
AC
SCR
BRIDGE
DC+
X1
X2
H2
H3
HIGH VOLTAGE
TRANSFORMER
CIRCUIT
SHUNT
DC-
AC
F
E
E
D
B
A
C
K
115VAC
18VAC
18VAC
CONTROL
BOARD
POWER
"ON"
DIGITAL
115VAC
FAN
DISPLAY
MODE
SWITCH
REMOTE
RECEPTACLE
THERMO-
STATS
THERMAL
LIGHT
GAS
VALVE
OUTPUT
CONTROL
AC
BALANCE
CONTROL
AUTO
BALANCE
LED
PULSE
FREQ.
LED
STICK
LED
TIG
LED
POSTFLOW
CONTROL
PULSE
CONTROL
OUTPUT RECTIFICATION AND
FEEDBACK CONTROL
The AC output from the main transformer secondary is
rectified and controlled through the SCR bridge.
Output current is sensed at the shunt as a low voltage
signal and fed back to the control board. The control
board compares the commands of the mode switch,
output control, AC balance control, pulse control, post-
flow control, or remote control with the feedback infor-
mation. The appropriate SCR gate firing signals are
created by the control board and sent to the SCR
bridge. The control board controls the firing of the
SCRs, which control the output of the machine. See
SCR Operation. The control board monitors the ther-
mostats, and also controls the gas solenoid valve, ther-
mal light, auto balance LED, pulse frequency LED, TIG
LED, stick LED, and the digital display.
NOTE: Unshaded areas of block logic diagrams are the subject of discussion.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-4
E-4
THEORY OF OPERATION
FIGURE E.4 High Voltage/High Frequency Circuit.
BY-PASS
BOARD
POLARITY
SWITCH
MAIN
TRANSFORMER
HI-FREQUENCY
TRANSFORMER
INPUT
POWER
SWITCH
BYPASS
C
H
O
K
E
ASBLY
H1
AC
SCR
BRIDGE
DC+
X1
X2
H2
H3
HIGH VOLTAGE
TRANSFORMER
CIRCUIT
SHUNT
DC-
AC
F
E
E
D
B
A
C
K
115VAC
18VAC
18VAC
CONTROL
BOARD
POWER
"ON"
DIGITAL
115VAC
FAN
DISPLAY
MODE
SWITCH
REMOTE
RECEPTACLE
THERMO-
STATS
THERMAL
LIGHT
GAS
VALVE
OUTPUT
CONTROL
HIGH VOLTAGE / HIGH
FREQUENCY CIRCUIT
The control board passes the 115VAC voltage to the
primary of the high voltage transformer. The sec-
ondary of the high voltage transformer is coupled to a
spark gap generator and also to the high frequency
transformer. The high frequency transformer transfers
the high frequency “spark” to the electrode terminal
which is coupled to the TIG torch.
NOTE: Unshaded areas of block logic diagrams are the subject of discussion.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-5
E-5
THEORY OF OPERATION
DC WELDING OUTPUT
When the polarity switch is placed in either DC position, the AC voltage from the main transformer secondary is
applied to the SCR bridge. The SCR bridge and choke circuits are connected in a conventional full wave bridge
and filter configuration, resulting in a controlled DC output. Since the choke is in series with the negative leg of
the bridge and also in series with the welding load, a filtered DC is applied to the machine output terminals.
CHOKE
ELECTRODE
G
G
DC
PRIMARY
1Ø
G
G
WORK
FIGURE E.5 DC Welding Current Generation.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-6
E-6
THEORY OF OPERATION
AC WELDING OUTPUT
Rotating the polarity switch to the AC position changes the welding power circuit. One lead (X1) of the main
transformer secondary is connected to the machine output work terminal. The other secondary lead (X2) is
connected to one of the AC connections on the SCR bridge. The electrode terminal is connected to the other
AC side of the bridge. The choke is now electrically across the negative and positive SCR bridge connections.
With the ability of the choke to store energy and the SCRs to turn on at the appropriate times, an AC square
wave is developed and applied to the output terminals.
CHOKE
G
G
ELECTRODE
G
G
AC
PRIMARY
1Ø
WORK
FIGURE E.6 AC Square Wave Welding Current Generation.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-7
E-7
THEORY OF OPERATION
SCR OPERATION
A silicon controlled rectifier (SCR) is a three terminal
device used to control rather large currents to a load.
An SCR acts very much like a switch. When a gate
signal is applied to the SCR it is turned ON and there
is current flow from anode to cathode. In the ON state
the SCR acts like a closed switch. When the SCR is
turned OFF there is no current flow from anode to
cathode thus the device acts like an open switch. As
the name suggests, the SCR is a rectifier, so it pass-
es current only during positive half cycles of the AC
supply. The positive half cycle is the portion of the
sine wave in which the anode of the SCR is more
positive than the cathode.
between gate and cathode, the voltage between these
terminals must be slightly greater than 0.6V. Once the
SCR has fired it is not necessary to continue the flow
of gate current. As long as current continues to flow
from anode to cathode the SCR will remain on. When
the anode to cathode current drops below a minimum
value, called holding current, the SCR will shut off.
This normally occurs as the AC supply voltage passes
through zero into the negative portion of the sine wave.
If the SCR is turned on early in the positive half cycle,
the conduction time is longer resulting in greater SCR
output. If the gate firing occurs later in the cycle the
conduction time is less resulting in lower SCR output.
When an AC supply voltage is applied to the SCR, the
device spends a certain portion of the AC cycle time in
the on state and the remainder of the time in the off
state. The amount of time spent in the ON state is con-
trolled by the Gate.
An SCR is fired by a short burst of current into the gate.
This gate pulse must be more positive than the cath-
ode voltage. Since there is a standard PN junction
INPUT
CATHODE
OUTPUT
NOTE: AS THE GATE
PULSE IS APPLIED
LATER IN THE CYCLE
THE SCR OUTPUT
IS DECREASED.
ANODE
GATE
GATE
FIGURE E.7 SCR Operation
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
E-8
E-8
THEORY OF OPERATION
by excessive output or duty cycle and the fan is oper-
ating normally, the power may be left on, and the reset
should occur within a 15 minute period. If the fan is not
functioning properly or the air intake louvers are
obstructed, then the input power must be removed and
the fan problem or air obstruction corrected.
PROTECTIVE CIRCUITS
Protective circuits are designed into the PRECISION
TIG 185 to sense trouble and shut down the machine
before the trouble damages the internal machine com-
ponents. Both thermal protection and current overload
are included. Fan as needed (F.A.N.) Fan runs for 5
seconds at power-up and stops at idle 8 minutes after
welding.
OVERLOAD PROTECTION
The machine is electronically protected from producing
excessively high output currents. The output is limited
to 200 amps.
THERMAL PROTECTION
9. OVER TEMPERATURE LIGHT-
If the welder
overheats due to blocked air flow, high ambient air
temperature, or exceeded duty cycle, an internal ther-
mostat will open disabling the welding output and this
yellow light will illuminate. The cooling fans will contin-
ue to run to cool the unit during this time. The light will
go out when the unit cools and the thermostat resets.
Once the light goes out, the machine will again
become available to weld.
Once the machine cools sufficiently the thermostats
are self-resetting. If the thermostat shutdown is caused
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section F-1
Section F-1
TABLE OF CONTENTS
- TROUBLESHOOTING & REPAIR SECTION -
Troubleshooting & Repair Section ........................................................................Section F
How to Use Troubleshooting Guide..............................................................................F-2
PC Board Troubleshooting Procedures and Replacement...........................................F-3
Troubleshooting Guide..................................................................................................F-4
Test Procedures
High Frequency Circuit Disable Procedure ..........................................................F-15
T1 Transformer Test..............................................................................................F-17
Static SCR Test ....................................................................................................F-21
Active SCR Test....................................................................................................F-25
Oscilloscope Waveforms
Normal Open Circuit Voltage Waveform-AC TIG Mode.......................................F-29
Normal Open Circuit Voltage Waveform-DC TIG Mode.......................................F-30
Normal Open Circuit Voltage Waveform-AC Stick Mode.....................................F-31
Normal Open Circuit Voltage Waveform-DC Stick Mode ....................................F-32
Typical Output Voltage Waveform-Machine Loaded AC TIG Mode.....................F-33
Typical Output Voltage Waveform-Machine Loaded DC TIG Mode ....................F-34
Typical Output Voltage Waveform-Machine Loaded AC Stick Mode ..................F-35
Typical Output Voltage Waveform-Machine Loaded DC Stick Mode..................F-36
Abnormal Open Circuit Voltage-DC TIG Mode One SCR not Functioning..........F-37
Replacement Procedures
SCR Bridge Assembly Removal and Replacement .............................................F-39
Polarity Switch Removal and Replacement .........................................................F-45
High Voltage Transformer Removal and Replacement ........................................F-49
Main Transformer and Output Choke Removal and Replacement......................F-53
Retest after Repair......................................................................................................F-57
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-2
F-2
TROUBLESHOOTING & REPAIR
CAUTION
This Troubleshooting Guide is provided to help
Step 3. PERFORM COMPONENT TESTS. The
last column, labeled “Recommended Course of
Action” lists the most likely components that may
have failed in your machine. It also specifies the
appropriate test procedure to verify that the
subject component is either good or bad. If there
are a number of possible components, check the
components in the order listed to eliminate one
possibility at a time until you locate the cause of
your problem.
you locate and repair possible machine
malfunctions. Simply follow the three-step
procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM). Look
under the column labeled “PROBLEM
(SYMPTOMS)”. This column describes possible
symptoms that the machine may exhibit. Find
the listing that best describes the symptom that
the machine is exhibiting. Symptoms are
grouped into three main categories: Feeding
Problems and Welding Problems.
All of the referenced test procedures referred to in
the Troubleshooting Guide are described in detail
at the end of this chapter. Refer to the
Troubleshooting and Repair Table of Contents to
locate each specific Test Procedure. All of the
referred to test points, components, terminal
strips, etc., can be found on the referenced
electrical wiring diagrams and schematics. Refer
to the Electrical Diagrams Section Table of
Contents to locate the appropriate diagram.
Step 2. PERFORM EXTERNAL TESTS. The
second column, labeled “POSSIBLE AREAS OF
MISADJUSTMENT(S)”, lists the obvious external
possibilities that may contribute to the machine
symptom. Perform these tests/checks in the
order listed. In general, these tests can be
conducted without removing the case
wrap-around cover.
WARNING
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF. Perform High
Frequency Disable Procedure.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-3
F-3
TROUBLESHOOTING & REPAIR
PC BOARD TROUBLESHOOTING PROCEDURES
- Remove the PC board from the static-shielding bag
and place it directly into the equipment. Don’t set the
PC board on or near paper, plastic or cloth which
could have a static charge. If the PC board can’t be
installed immediately, put it back in the static-shield-
ing bag.
WARNING
ELECTRIC SHOCK
can kill.
•
Have an electrician install and
service this equipment. Turn the
input power OFF at the fuse box
before working on equipment. Do
not touch electrically hot parts.
- If the PC board uses protective shorting jumpers,
don’t remove them until installation is complete.
- If you return a PC board to The Lincoln Electric
Company for credit, it must be in the static-shielding
bag. This will prevent further damage and allow prop-
er failure analysis.
CAUTION
Sometimes machine failures appear to be due to PC
board failures. These problems can sometimes be
traced to poor electrical connections. To avoid prob-
lems when troubleshooting and replacing PC boards,
please use the following procedure:
4. Test the machine to determine if the failure
symptom has been corrected by the
replacement PC board.
NOTE: It is desirable to have a spare (known good)
PC board available for PC board troubleshooting.
1. Determine to the best of your technical ability
that the PC board is the most likely component
causing the failure symptom.
NOTE: Allow the machine to heat up so that all
electrical components can reach their operating
temperature.
2. Check for loose connections at the PC board
to assure that the PC board is properly
connected.
5. Remove the replacement PC board and
substitute it with the original PC board to
recreate the original problem.
3. If the problem persists, replace the suspect PC
board using standard practices to avoid static
electrical damage and electrical shock. Read
the warning inside the static resistant bag and
perform the following procedures:
a. If the original problem does not reappear by
substituting the original board, then the PC
board was not the problem. Continue to look
for bad connections in the control wiring
harness, junction blocks, and terminal strips.
PC board can be damaged by static electricity.
b. If the original problem is recreated by the
substitution of the original board, then the PC
board was the problem. Reinstall the
replacement PC board and test the machine.
- Remove your body’s static
charge before opening the static-
shielding bag. Wear an anti-static
wrist strap. For safety, use a 1
Meg ohm resistive cord connected
6. Always indicate that this procedure was
followed when warranty reports are to be
submitted.
to
a
grounded part of the
ATTENTION
Static-Sensitive
Devices
Handle only at
Static-Safe
equipment frame.
NOTE: Following this procedure and writing on the
warranty report, “INSTALLED AND SWITCHED PC
BOARDS TO VERIFY PROBLEM,” will help avoid
denial of legitimate PC board warranty claims.
- If you don’t have a wrist strap,
touch an un-painted, grounded,
part of the equipment frame. Keep
touching the frame to prevent
static build-up. Be sure not to
touch any electrically live parts at
the same time.
Workstations
- Tools which come in contact with the PC board must
be either conductive, anti-static or static-dissipative.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-4
F-4
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
OUTPUT PROBLEMS
Machine is dead. No output - No
fan
1. Make sure that the input power 1. Check the input power switch
switch is in the "ON" position and
the machine is plugged in.
and associated wires for loose or
faulty connections.
2. Check the input voltage at the
machine. Input voltage must
match the rating plate and volt-
age connection. Refer to
Reconnect Procedure in the
Installation section of this manu-
al.
2. Perform the T1 Transformer
Test.
3. Blown or missing fuses in the
input line.
The fan runs normally. No output
from the machine in either Stick or
TIG modes.
1. Check for proper input voltages 1. Check for loose or faulty connec-
per nameplate and voltage
reconnect configuration.
tions on the heavy current carry-
ing leads. (polarity switch, output
choke output terminals etc.)
2. Check to make sure the polarity
switch is in the proper position
and functioning correctly.
2. Perform the T1 Transformer
Test.
3. Perform the SCR Bridge Test.
4. Check current control R1 for
proper operation. Normal resis-
tance is 10,000 ohms. Also
check associated leads for loose
or faulty connections.
5. The control board may be faulty.
Replace.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-5
F-5
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
OUTPUT PROBLEMS
Fan runs - No output from machine 1. The welding application may
1. One of the thermostats may be
faulty. Check or replace. See
wiring diagram.
in either Stick or TIG modes and the
yellow light on the control panel is
on.
have exceeded the recommend-
ed duty cycle. Allow the unit to
run until the fan cools the unit
and the yellow light goes out.
2. Check for loose or faulty wires on
the thermostats and associated
circuitry. See wiring diagram.
2. The air louvers may be blocked.
Remove air obstruction and allow
unit to cool.
The machine does not respond (no 1. Make certain the machine is in
1. Check the continuity (zero ohms)
of the leads between the remote
receptacle and plug J5 on the
control board. See wiring dia-
gram.
gas flow, no high frequency and no
open circuit voltage) when the arc
the TIG mode.
start switch or Amptrol is activated - 2. The Amptrol may be defective.
fan is working normally.
Check for continuity(zero ohms)
between pins "D" and "E" on
cable connector when the
Amptrol is depressed.
2. Perform the T1 Transformer
Test.
3. The control board may be faulty.
Replace.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-6
F-6
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
OUTPUT PROBLEMS
Machine regularly over heats - ther- Machine regularly over heats - ther- 1. The thermostat(s) may be faulty.
mostat opens. Yellow light on front mostat opens. Yellow light on front
Check or replace.
panel glows. The fan runs but the
machine has no output.
panel glows. The fan runs but the
machine has no output.
2. The control board may be faulty.
The machine does not have output The machine does not have output 1. Check the Stick/TIG switch(S3)
in the Stick mode. The machine
operates correctly in the TIG mode. operates correctly in the TIG mode.
in the Stick mode. The machine
and associated leads. See
wiring diagram.
2. The control board may be faulty.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-7
F-7
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
OUTPUT PROBLEMS
Machine welds at a very low output 1. If welding in the TIG mode the
1. Check the polarity switch and
associated leads.
regardless of the current control set-
ting.
remote control device may be
defective.
2. Check the interior connections of
the heavy current carrying leads.
2. Make certain the input line volt-
age is correct for the machine
reconnect configuration.
3. Perform the SCR Bridge Test.
3. Check the welding cables and or 4. Perform the T1 Transformer
torch for loose or faulty connec-
tions.
Test.
5. Check the current control for
proper operation. Normal resis-
tance is 10k ohms. See wiring
diagram.
6. The control board may be faulty.
The machine welds at a very high
output regardless of the current con-
trol setting.
1. If welding in the TIG mode the
remote control device may be
defective.
1. Perform the SCR Bridge Test.
2. Perform the T1 Transformer
Test.
3. Check the current control for
proper operation. Normal resis-
tance is 10k ohms. See wiring
diagram.
4. The control board may be faulty.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-8
F-8
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG MODE PROBLEMS
Machine output is intermittently lost. 1. The problem may be caused by 1. Check for loose or faulty connec-
Gas flow and high frequency are
also interrupted.
high frequency interference.
Make sure that the machine is
grounded properly according to
the installation instructions. If
there are other high frequency
tion on the leads between the
remote receptacle and plug J5
on the control board. See wiring
diagram.
sources in the area, make certain 2. Check the plugs on the control
that they are grounded properly. board for loose connections.
2. Make sure the Amptrol is operat- 3. The control board may be faulty.
ing properly.
3. Check to make sure that the
input voltage is correct for the
machine reconnect configuration.
Refer to Reconnect Procedure
in the Installation section of this
manual.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-9
F-9
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG MODE PROBLEMS
The arc "flutters" when TIG welding. 1. The tungsten electrode may be 1. Check the polarity switch for
too large in diameter for the cur-
rent setting.
proper operation and loose or
faulty lead connections. See
wiring diagram.
2. The tungsten tip may not be
"sharp" enough.
2. Perform the SCR Bridge Test.
3. Check for loose or faulty connec-
tions at the shunt. ( leads #221
and #222 ).
3. The gas shielding may be insuffi-
cient. Increase the gas flow and
or reduce the tungsten stickout
beyond the gas cup.
4. Check components R3 and C4 in
the high voltage transformer pri-
mary circuit. Replace if neces-
sary. See wiring diagram.
4. Check for contaminated gas or
leaks in the gas line, torch, or
connections.
5. The control board may be faulty.
Replace.
5. If a helium blend is used as a
shielding gas then reduce the
percentage of helium.
The arc "pulsates" when AC TIG
welding.
1. Make sure the gas and proce-
dure are correct for the process
being used.
1. Check the micro switch S2A on
the polarity switch. It may be
stuck closed. See wiring dia-
gram.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-10
F-10
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG WELDING PROBLEMS
Black areas along weld bead.
1. Clean any oily or organic conta- 1. This may be a welding proce-
mination from the work piece. dure problem.
2. Tungsten electrode may be cont- Contact The Lincoln Electric Service
aminated. Replace or sharpen. Department, 1-888-935-3877.
3. Check for contaminated gas or
leaks in the gas line, torch, or
associated connections.
4. The gas shielding may be insuffi-
cient. Increase gas flow: reduce
tungsten stickout beyond the gas
cup.
Weak high frequency - machine has 1. Check for loose or faulty connec- 1. Make sure that 115VAC is being
normal welding.
tions at the torch and/or welding
cables.
applied to the primary of the high
voltage transformer (T3). See
wiring diagram.
2. The gas shielding may be insuffi-
cient. Increase gas flow: reduce 2. Check for any open or arcing
tungsten stickout beyond the gas
cup.
high frequency component.
Replace as required.
(Examples: C3, R3, C4)
3. Check spark gap operation and
setting. Normal is (0.015").
Refer to Maintenance section of 3. If spark is weak at the spark gap,
this manual.
check or replace the high fre-
quency circuit.
4. The work and electrode cables
may be in poor condition allowing
the high frequency to "leak off".
Use good quality cables with a
high natural rubber content, such
as Lincoln Stable Arc Cable.
Cables should be as short as
possible.
(Examples: T3, L3, L4).
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-11
F-11
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG WELDING PROBLEMS
High frequency "spark" is present at 1. The torch may be faulty. Check 1. This may be a welding procedure
tungsten electrode, but operator is
unable to establish a welding arc.
Machine has normal open circuit
voltage. Refer to Technical
Specifications in the Installation
Chapter.
or replace.
problem.
2. The current control may be set
too low.
Contact The Lincoln Electric Service
Department 1-888-935-3877.
3. The tungsten electrode may be
contaminated. Replace or sharp-
en.
4. The electrode may be too large
for the process.
5. If a helium blend is being used
as a shielding gas, then reduce
the percentage of helium.
6. Check the welding cables for
loose or faulty connections.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-12
F-12
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG WELDING PROBLEMS
No high frequency. Machine is in
the TIG mode and has normal out-
put.
1. If the machine location is in a
1. Check the high voltage trans-
highly dirty environment with con-
ductive contaminants, check and
clean the spark gap with a low
pressure air stream per the main-
tenance instructions.
former (T3). The normal resis-
tance of the secondary winding
of the high voltage transformer is
12.5k ohms.
WARNING
2. Check spark gap operation and
setting. Normal is (0.020").
Refer to Maintenance section of
this manual.
ELECTRIC SHOCK CAN
KILL. When 115VAC is
applied to the primary of
T3. A very high voltage is devel-
oped on the secondary winding.
For assistance call the Lincoln
Electric Service Department 1-888-
935-3877.
------------------------------------------------
2. Check the values of R3, and C4.
3. Perform the T1 Transformer Test.
4. The control board may be faulty.
Replace.
No gas flow when Amptrol is activat- 1. The gas supply is either empty or 1. Possible gas supply problems.
ed in the TIG mode. Machine has
normal output - fan runs.
A "click" can be heard indicating that 2. The flow regulator may be set
not turned on.
Consult your local welder/gas dis-
tributor.
the gas solenoid valve is operating.
too low.
3. Check the gas hose for kinks or
blockages.
4. Check the filter screen inside gas
inlet fitting to solenoid valve.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-13
F-13
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
TIG WELDING PROBLEMS
When AC TIG welding, the arc is
erratic and there is a loss of "clean-
ing" of the work piece.
1. The tungsten electrode may be 1. Check components R3 and C4 in
too small for the process. Use a
larger diameter tungsten or a
pure tungsten.
the high voltage transformer pri-
mary circuit.
2. If a helium blend is used as a
shielding gas, then reduce the
percentage of helium.
2. Perform the SCR Bridge Test.
The end of the tungsten electrode
melts away.
1. The welding current is too high
for the electrode type and or
size. See Table B.1 in the
Operation Section.
1. This may be a welding procedure
problem.
Contact The Lincoln Electric Service
Department 1-888-935-3877.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-14
F-14
TROUBLESHOOTING & REPAIR
TROUBLESHOOTING GUIDE
Observe Safety Guidelines
detailed in the beginning of this manual.
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
STICK WELDING PROBLEMS
Stick electrode "Blasts Off" when arc 1. Weld current may be set too high 1. Perform the SCR Bridge Test.
is struck.
for electrode size. Reduce cur-
rent control setting, or use a larg- 2. The control board may be faulty.
er diameter electrode.
Replace.
The stick electrode "sticks" in the
puddle.
1. The weld current may be set too
low. Increase the current control
setting or use a smaller diameter
electrode.
Variable or sluggish welding arc
when welding in the Stick mode.
1. Check work and electrode cables 1. Check the polarity switch for
for loose or poor connections.
excessive wear or faulty connec-
tions.
2. The weld cables may be too small
or too long to permit the desired 2. Check interior connection of the
current to flow.
heavy current carrying leads.
3. The weld current may be set too
low.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con-
tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
1-888-935-3877.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-15
F-15
TROUBLESHOOTING & REPAIR
HIGH FREQUENCY CIRCUIT DISABLE PROCEDURE
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will disable the high frequency circuit. The technician will then be able to
take voltage measurements without the possibility of high frequency damage to his test
equipment.
MATERIALS NEEDED
3/8” Nutdriver
5/64” Allen type wrench
.020” feeler gauge
WARNING
HIGH VOLTAGE IS STILL PRESENT IN THE HIGH FREQUENCY CIRCUIT.
----------------------------------------------------------------------------------------------------------------------------
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-16
F-16
TROUBLESHOOTING & REPAIR
HIGH FREQUENCY CIRCUIT DISABLE PROCEDURE
5. Increase the distance between the
PROCEDURE
electrodes to at least 3/8” by sliding
one electrode away from the other
1. Remove input power to the TIG185
electrode. Secure the one electrode
machine.
in this position.
2. Using the 3/8” nutdriver remove the
6. This should disable the high frequen-
right side panel.
cy circuit. Visually check to make
sure high frequency sparking is
3. Locate the Spark Gap Assembly at
NOT present before connecting
the right side of the machine. See
any test equipment to the TIG 185
Figure F.1.
machine.
4. With the 5/64” Allen type wrench
7. When voltage testing and scope
loosen the set screw holding the
measurements are complete reset
upper electrode in place.
the spark gap electrodes to .020” air
gap. Tighten the set screw using the
5/64” Allen wrench.
FIGURE F.1 SPARK GAP ASSEMBLY
.020Spark Gap
LEFT SIDE OF MACHINE
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-17
F-17
TROUBLESHOOTING & REPAIR
T1 TRANSFORMER TEST
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will determine if the correct voltage is being applied to the primary of the
T1 transformer and also if the correct voltages are being induced on the secondary
windings of the transformer.
MATERIALS NEEDED
Volt/Ohm Meter
Precision TIG 185 Wiring Diagrams
3/8” nutdriver
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-18
F-18
TROUBLESHOOTING & REPAIR
T1 TRANSFORMER TEST (continued)
4. Carefully apply the correct input
TEST PROCEDURE
power making certain the reconnect
configuration at the input switch is
correct for the input voltage applied.
Turn the TIG 185 ON.
1. Remove main supply power to the
machine.
2. Using the 3/8” nutdriver remove the
case wrap-around cover.
5. Using the voltmeter carefully test for
the correct transformer secondary
voltages per Table F.1.
3. Locate plugs J3 and J4 on the
control board. See Figure F.2.
FIGURE F.2 - Plugs J3 & J4 on Control Board
PRECISION TIG 185 CONTROL BOARD
PIN 7 (LEAD #209)
PIN 8 (LEAD #210)
PIN 3 (LEAD #204)
PIN 4 (LEAD #201)
PIN 3 (LEAD #232)
PIN 2 (LEAD #260)
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-19
F-19
TROUBLESHOOTING & REPAIR
T1 TRANSFORMER TEST (continued)
6. If all of the secondary voltages are
Choke
Removal
and
correct the T1 transformer is func-
tioning properly.
Replacement. Also check the
leads for broken or loose connec-
tions between plugs J3, J4 and
the T1 transformer.
A. If all of the secondary voltages
are missing or incorrect make
certain that the correct input volt-
age is being applied to the correct
primary leads. See Table F.1.
7. Replace case wrap-around cover.
B. If the correct input voltage is
being applied to the primary leads
and any or all of the secondary
voltages are incorrect the T1
transformer may faulty.
See
Main Transformer and Output
TABLE F.1 T1 TRANSFORMER VOLTAGE
TEST POINTS
ACCEPTABLE VOLTAGES
SECONDARY VOLTAGES
SECONDARY WINDINGS
PLUG J3 PIN 8 (LEAD #210)
TO
PLUG J3 PIN 7 (LEAD #209)
18VAC
18VAC
PLUG J3 PIN 4 (LEAD #201)
TO
PLUG J3 PIN 3 (LEAD #204)
PLUG J4 PIN 2 (LEAD #260)
TO
CHECK DURING FIRST 5 SECONDS OF POWER UP
115VAC
PLUG J4 PIN 3 (LEAD #232)
X1 TO X2
PRIMARY WINDINGS
H1 TO H2
80 VAC
PRIMARY VOLTAGES
208VAC
H1 TO H3
230VAC
NOTE: If the input voltages vary the secondary voltages will vary accordingly.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-20
F-20
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-21
F-21
TROUBLESHOOTING & REPAIR
STATIC SCR TEST
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure is a quick check to determine if an SCR is shorted or “leaky”. See
machine waveform section for normal and abnormal SCR waveforms.
MATERIALS NEEDED
Volt/Ohm Meter (Analog)
Precision TIG 185 Wiring Diagrams
3/8” nutdriver
SCR Heat Sink Assembly Drawing
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-22
F-22
TROUBLESHOOTING & REPAIR
STATIC SCR TEST (continued)
TEST PROCEDURE
1. Remove main supply power to the
TIG 185 and remove the case wrap-
around cover.
2. Locate and remove plug J2 from the
control board. See Figure F.3.
Figure F.3 - Plug J2 Location on Control Board
PLUG J2 REMOVED
PRECISION TIG 185 CONTROL
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-23
F-23
TROUBLESHOOTING & REPAIR
STATIC SCR TEST (continued)
3. Using an analog ohmmeter test the
resistance from anode to cathode of
SCR1. Reverse the meter leads and
check from cathode to anode of
SCR1. See Figure F.4. If a low resis-
tance is indicated in either direction
SCR1 is faulty. Replace SCR Bridge
Assembly. See SCR Bridge
5. The further check the SCR’s func-
tions use an SCR tester and proceed
to the Active SCR Test.
Assembly
Removal
and
Replacement.
4. Repeat Step #3 testing SCR2, SCR3
and SCR4.
FIGURE F.4 SCR TEST POINTS
SCR2 CATHODE
SCR3 CATHODE
SCR4 ANODE
SCR1 ANODE
SCR1 CATHODE/SCR2 ANODE
SCR3 ANODE/SCR4 CATHODE
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-24
F-24
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-25
F-25
TROUBLESHOOTING & REPAIR
ACTIVE SCR TEST
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will determine if the device is able to be gated “ON” and conduct current
from anode to cathode.
MATERIALS NEEDED
An SCR tester as outlined in this procedure.
Precision TIG 185 Wiring Diagrams
3/8” nutdriver
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-26
F-26
TROUBLESHOOTING & REPAIR
ACTIVE SCR TEST (continued)
4. Construct the circuit outlined in Figure
TEST PROCEDURE
F.5. One 6V lantern battery can be
used. Resistor values are ±10%. The
voltmeter scale should be low,
approximately 0-5 or 0-10 volts.
1. Remove main supply power to the
TIG 185 machine.
2. Locate and remove plug J2 from the
5. Battery Test - Check the battery by
shorting leads (A) and (C) and then
close switch SW-1. Re-place battery if
voltage is less than 4.5 volts.
control board. See Figure F.3.
3. Perform test procedure as outlined in
Figure F.5. Repeat test for all four
SCRs. See Figure F.6.
FIGURE F.5 ACTIVE SCR TEST SETUP
SW1
R2
V
R1
SW2
6volt
Lantern
Battery
A
G
SCR
under
test
C
R1= 4 ohms /10 watts
R2= 3 ohms/ 10 watts
To test SCRs construct the circuit outlined above.
Resistor values are plus or minus ten percent. The
voltmeter scale should be low, approximately 0-5 or
0-10 volts DC.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-27
F-27
TROUBLESHOOTING & REPAIR
ACTIVE SCR TEST (continued)
SCR2 CATHODE
SCR3 CATHODE
SCR1 ANODE
SCR4 ANODE
SCR1 CATHODE/SCR2 ANODE
SCR3 ANODE/SCR4 CATHODE
PLUG J2
3
4
SCR3
SCR4
SCR1
1
SCR2
2
S24018-4 (INSERTION SIDE)
SCR GATE LEADS/TEST POINTS
FIGURE F.6 SCR GATE LOCATIONS
6. Connect SCR into the test circuit as
shown (A) lead to anode (C) lead to
cathode and (G) lead to the gate.
9. Open switch SW-1, disconnect the
gate lead (G) and reverse the (A) and
(C) leads on the SCR. Close switch
SW-1. The voltmeter should read
zero. If the voltage is higher than
zero, the SCR is shorted.
7. Close switch SW-1 (switch SW-2
should open), voltmeter should read
zero. If the voltmeter reads higher
than zero the SCR is shorted.
10. Replace SCR Bridge Assembly if
any SCRs do not pass the test in
8. With switch SW-1 closed, close
switch SW-2 for two seconds and
release. The voltmeter should read 3
to 6 volts before and after switch SW-
2 is released. If the voltmeter does not
read, or reads only while SW-2 is
depressed, the SCR or battery is
defective (repeat Battery Test
Procedure above).
Step #3.
Assembly
Replacement.
See SCR Bridge
Removal and
11. Replace plug J2 into the control
board.
12. Replace the case wrap-around
cover.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-28
F-28
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-29
F-29
TROUBLESHOOTING & REPAIR
NORMAL OPEN CIRCUIT VOLTAGE WAVEFORM
AC TIG MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
50 V
2 ms
This is the typical AC output voltage wave-
form generated from a properly operating
machine. Note that each vertical division
represents 50 volts and that each horizontal
division represents 2 milliseconds in time.
SCOPE SETTINGS
Volts/Div. ...............................50 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-30
F-30
TROUBLESHOOTING & REPAIR
NORMAL OPEN CIRCUIT VOLTAGE WAVEFORM
DC TIG MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
50 V
2 ms
This is the typical DC (+) output voltage
waveform generated from a properly operat-
ing machine. Note that each vertical division
represents 50 volts and that each horizontal
division represents 2 milliseconds in time.
SCOPE SETTINGS
Volts/Div. ...............................50 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-31
F-31
TROUBLESHOOTING & REPAIR
NORMAL OPEN CIRCUIT VOLTAGE WAVEFORM
AC STICK MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
50 V
2 ms
This is the typical AC output voltage wave-
form generated from a properly operating
machine. Note that each vertical division
represents 50 volts and that each horizontal
division represents 2 milliseconds in time.
SCOPE SETTINGS
Volts/Div. ...............................50 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-32
F-32
TROUBLESHOOTING & REPAIR
NORMAL OPEN CIRCUIT VOLTAGE WAVEFORM
DC STICK MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
50 V
2 ms
This is the typical DC (+) output voltage
waveform generated from a properly operat-
ing machine. Note that each vertical division
represents 50 volts and that each horizontal
division represents 2 milliseconds in time.
SCOPE SETTINGS
Volts/Div. ...............................50 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
Note: Scope probes connected at machine
output studs: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-33
F-33
TROUBLESHOOTING & REPAIR
TYPICAL OUTPUT VOLTAGE WAVEFORM - MACHINE LOADED
AC TIG MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
10 V
2 ms
MACHINE LOADED TO 180 AMPS AT
16VDC.
SCOPE SETTINGS
Volts/Div. ...............................10 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
This is the typical AC output voltage wave-
form generated from a properly operating
machine. Note that each vertical division
represents 10 volts and that each horizontal
division represents 2 milliseconds in time.
The machine was loaded with a resistance
grid bank. The grid load meters read 180
amps and 16VDC
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-34
F-34
TROUBLESHOOTING & REPAIR
TYPICAL OUTPUT VOLTAGE WAVEFORM - MACHINE LOADED
DC TIG MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
10 V
MACHINE LOADED TO 180 AMPS AT
16VDC.
SCOPE SETTINGS
Volts/Div. ...............................10 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
This is the typical DC (+) output voltage
waveform generated from a properly operat-
ing machine. Note that each vertical division
represents 10 volts and that each horizontal
division represents 2 milliseconds in time.
The machine was loaded with a resistance
grid bank. The grid load meters read 180
amps and 16VDC
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-35
F-35
TROUBLESHOOTING & REPAIR
TYPICAL OUTPUT VOLTAGE WAVEFORM - MACHINE LOADED
AC STICK MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
10 V
2 ms
MACHINE LOADED TO 180 AMPS AT
26VDC.
SCOPE SETTINGS
Volts/Div. ...............................10 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
This is the typical AC output voltage wave-
form generated from a properly operating
machine. Note that each vertical division
represents 10 volts and that each horizontal
division represents 2 milliseconds in time.
The machine was loaded with a resistance
grid bank. The grid load meters read 180
amps and 26VDC
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-36
F-36
TROUBLESHOOTING & REPAIR
TYPICAL OUTPUT VOLTAGE WAVEFORM - MACHINE LOADED
DC STICK MODE
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
10 V
2 ms
MACHINE LOADED TO 180 AMPS AT
26VDC.
SCOPE SETTINGS
Volts/Div. ...............................10 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
This is the typical AC output voltage wave-
form generated from a properly operating
machine. Note that each vertical division
represents 10 volts and that each horizontal
division represents 2 milliseconds in time.
The machine was loaded with a resistance
grid bank. The grid load meters read 180
amps and 26VDC
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-37
F-37
TROUBLESHOOTING & REPAIR
ABNORMAL OPEN CIRCUIT VOLTAGE - DC TIG MODE
ONE OUTPUT SCR NOT FUNCTIONING
CAUTION
HIGH VOLTAGE / HIGH FREQUENCY can damage test equipment.
• Perform all voltage and waveform checks with high frequency circuit OFF.
• Perform High Frequency Disable Procedure.
____________________________________________________________________
0 V
50 V
This is NOT the typical DC (+) output voltage
waveform. One output SCR is not function-
ing. Note the “gap”in the waveform. One
SCR gate was disconnected to simulate an
open or non-functioning output SCR. Note
that each vertical division represents 50
volts and that each horizontal division repre-
sents 2 milliseconds in time.
SCOPE SETTINGS
Volts/Div. ...............................50 V/Div.
Horizontal Sweep .................2 ms/Div.
Coupling.........................................DC
Trigger.....................................Internal
Note: Scope probes connected at machine
output terminals: (+) probe to electrode, (–)
probe to work.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-38
F-38
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-39
F-39
TROUBLESHOOTING AND REPAIR
SCR BRIDGE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will aid the technician in the removal and replacement of the SCR
assembly
MATERIALS NEEDED
5/16” nutdriver
3/8” nutdriver
Needle nose pliers
7/16” Wrench
3/8” Wrench
Slot head screwdriver
Dow Corning 340 Heat Sink compound
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-40
F-40
TROUBLESHOOTING AND REPAIR
SCR BRIDGE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
6. Remove the gas hose from the gas
PROCEDURE
solenoid valve.
1. Remove input power to the TIG 185
7. Carefully pull the case back and fan
assembly away to allow access to
the SCR Bridge Assembly. Support
the case back so as not to stress the
fan motor leads. It is not necessary
to disconnect the fan motor leads.
machine.
2. Using the 3/8” nutdriver remove the
case wrap-around cover.
3. With the slot head screwdriver
loosen the input cable strain relief to
allow movement of case back.
8. Using the 5/16” nutdriver remove the
two screws holding the front panel
assembly to the base. See Figure
F.8.
4. Using the 3/8” nutdriver remove the
two lower screws from the case back.
See Figure F.7.
5. With the 5/16” nutdriver remove the
two screws holding the case back to
the internal divider panel. See Figure
F.7.
FIGURE F.7 CASE BACK MOUNTING SCREWS
REAR PANEL
MOUNTING
SCREWS
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-41
F-41
TROUBLESHOOTING AND REPAIR
SCR BRIDGE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
FIGURE F.8 FRONT PANEL MOUNTING SCREWS
FRONT PANEL
MOUNTING
SCREWS
9. Remove plug J2 from the control
board. (See Figure F.9.) Also
X2 secondary transformer lead from
the left side AC SCR heat sink.
remove plug and lead harness from
internal divider panel.
13. With the 7/16” wrench remove the
shunt from the SCR bridge left side
negative heat sink.
10. Carefully slide the internal divider
panel away a few inches to allow
access to the SCR bridge assem-
bly.
14. Using the 7/16” wrench remove the
polarity switch lead from the right
side AC SCR heat sink.
11. Using the 7/16” wrench disconnect
the diode pigtail connection from the
polarity switch lead. See Figure
F.10. Cut any necessary cable ties
and remove insulating sleeving.
15. Using the 7/16” wrench remove the
positive lead from the right side
positive heat sink.
Note placement of sleeving and cable
ties for reassembly.
12. Using the 7/16” wrench remove the
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-42
F-42
TROUBLESHOOTING & REPAIR
SCR BRIDGE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
FIGURE F.9 PLUG J2 ON CONTROL BOARD
PLUG J2 REMOVED
PRECISION TIG 185 CONTROL
DIODE
PIGTAIL
CONNECTION
FIGURE F.10 DIODE PIGTAIL CONNECTION TO POLARITY SWITCH LEAD.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-43
F-43
TROUBLESHOOTING & REPAIR
SCR BRIDGE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
16. With the 3/8” wrench remove the
four mounting screws holding the
SCR bridge assembly to the main
transformer frame. Note insulator
placement.
9. Position the internal divider panel
and secure with the screws previous-
ly removed.
10. Install the J2 plug into the control
board and position the harness in
the internal divider panel.
17. Carefully remove the SCR bridge
assembly from the TIG 185 cutting
any necessary cable ties.
11. Position and install the case back
and secure with the screws previ-
ously removed.
REPLACEMENT PROCEDURE
12. Install the gas hose onto the sole-
noid valve.
1. Carefully place the new SCR bridge
assembly in position in the TIG 185.
13. Tighten the input cable strain relief.
2. Using the 3/8” wrench install the four
mounting screws taking special care
that the insulators are in the correct
positions.
14. Assemble the case wrap-around
cover.
USE DOW CORNING 340 HEAT SINK
COMPOUND ON ALL ALUMINUM
CONNECTIONS
3. Assemble the positive lead to the
right side positive heat sink.
4. Assemble the lead from the polarity
switch to the right side AC heat sink.
Note: Also connect lead #216
5. Assemble the shunt to the SCR
bridge left side negative heat sink.
6. Assemble the X2 secondary trans-
former lead to the left side AC SCR
heat sink. Note: Also connect lead
#217
7. Assemble the diode pigtail lead to
the polarity switch lead. See Figure
F.10. Be sure to replace sleeving
and secure with cable ties. Position
with harness and secure with cable
ties.
8. Replace any previously removed
cable ties.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-44
F-44
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-45
F-45
TROUBLESHOOTING & REPAIR
POLARITY SWITCH
REMOVAL AND REPLACEMENT PROCEDURE
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will aid the technician in the removal and replacement of the polarity
switch.
MATERIALS NEEDED
3/8” Nutdriver
1/2” Wrench
7/16” Wrench
Phillips head screwdriver
5/64” Allen type Wrench
Needle nose pliers
Slot head screwdriver (2 required)
Wiring diagram
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-46
F-46
TROUBLESHOOTING & REPAIR
POLARITY SWITCH
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
tion point for reassembly.
REMOVAL PROCEDURE
12. Using the 1/2” wrench remove the
other flat copper lead from the
polarity switch. This lead connects
to the lower terminal on the by-pass
board and the “work” lead. See
1. Remove the input power to the TIG
185 machine.
2. Using the 3/8” nutdriver remove the
case wrap-around cover.
wiring diagram.
Label lead and
connection point for reassembly.
3. Using the 3/32” Allen type wrench
remove the output control knob.
13. Using the 1/2” wrench remove the
choke lead from the polarity switch.
See wiring diagram. Label lead and
connection point for reassembly.
4. Using the Phillips head screwdriver
remove the screw from the polarity
switch handle.
14. With the 1/2” wrench remove the X1
secondary lead from the polarity
switch. See wiring diagram. Label
lead and connection point for
reassembly.
5. With the 2 slot head screwdrivers
carefully pry the polarity switch han-
dle from the shaft.
6. Remove the five plastic snap rivets
holding the name plate to the case
front. These can be removed by gen-
tly prying at the rivet between the
name plate and the case front.
15. With the 7/16” wrench remove the
two nuts and washers that hold the
polarity switch to the front panel.
16. Carefully rotate the polarity switch
assembly to gain access to the
micro-switch.
7. Remove the name plate.
8. With the 1/2” wrench remove the
“positive” flex lead from the polarity
switch. See wiring diagram. Label
lead and connection point for
reassembly.
17. Carefully unsolder the two leads
(#311 and #312) from the micro-
switch located on the polarity switch
assembly. See wiring diagram.
Label leads and connection points
for reassembly.
9. With the 1/2” wrench remove the
“AC” flex lead from the polarity
switch. This lead connects to the AC
plate on the SCR bridge. See wiring
diagram. Label lead and connection
point for reassembly.
18. Carefully remove the polarity switch
assembly from the machine.
10. Using the 1/2” wrench remove the
flex lead from the rear gang of the
polarity switch. This lead connects
to the D1 diode on the SCR bridge.
See wiring diagram. Label lead and
connection point for reassembly.
11. Using the 1/2” wrench remove the
flat copper lead from the polarity
switch. This lead connects to the
high frequency transformer coil and
the by-pass board. See wiring
diagram. Label lead and connec-
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-47
F-47
TROUBLESHOOTING & REPAIR
POLARITY SWITCH
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
8. Assemble the flex lead from the AC
REPLACEMENT PROCEDURE
bridge plate to the polarity switch.
Make certain washers are in place
and the nut is tight.
1. Carefully position the new polarity
switch in position on the front panel.
Make certain the micro-switch is
assembled to the polarity switch cor-
rectly.
9. Assemble the “positive” flex lead to
the polarity switch. Make certain
washers are in place and the nut is
tight.
2. Solder leads #311 and #312 to the
micro -switch.
10. Clear the leads and check for
“shorted” or “grounded” leads.
3. Assemble and tighten the two nuts
and washers that hold the polarity
switch to the front panel.
11. Position the name plate and fasten
to the front with the previously
removed snap rivets.
4. Assemble the X1 secondary lead to
the polarity switch. Make certain
washers are in place and the nut is
tight.
12. Assemble the polarity switch handle
in place with the Phillips head screw
and check for correct switch opera-
tion.
5. Assemble the choke lead to the
polarity switch. Make certain wash-
ers are in place and the nut is tight.
13. Using the Allen type wrench replace
the output control knob.
6. Assemble the flat copper leads to the
polarity switch. Make certain they
are connected to the proper termi-
nals and the nuts are tightened.
14. Replace the case wrap-around
cover.
7. Assemble the flex lead from diode
D1 to the rear gang of the polarity
switch. Make certain washers are in
place and the nut is tight.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-48
F-48
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-49
F-49
TROUBLESHOOTING & REPAIR
HIGH VOLTAGE TRANSFORMER
REMOVAL AND REPLACEMENT PROCEDURE
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will aid the technician in the removal and replacement of the high voltage
transformer.
MATERIALS NEEDED
3/8” Nutdriver
Phillips head screwdriver
Needle nose pliers
Wire cutters
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-50
F-50
TROUBLESHOOTING & REPAIR
HIGH VOLTAGE TRANSFORMER
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
6. Using the phillips head screwdriver
REMOVAL PROCEDURE
remove the front mounting screws from
the base of the high voltage transformer.
Take note of insulator placement for
reassembly. NOTE: On some machines
the mounting screw configuration may be
different.
1. Remove input power to the TIG 185
machine.
2. Using the 3/8” nutdriver remove the case
wrap-around cover.
7. With phillips head screwdriver loosen the
two rear mounting screws.
3. With the needle nose pliers remove the
two secondary leads from the quick-con-
nects on the high frequency arc starter
board assembly. See Figure F.11.
8. Carefully slide the transformer forward
and remove from the TIG 185 machine.
4. Disconnect the in-line splice quick con-
nect from one primary lead to lead #231A.
Cut any necessary cable ties.
5. Remove the lead splice from the other pri-
mary lead that is connected to lead #236
and the C4 capacitor. See wiring dia-
gram. Cut any necessary cable ties.
FIGURE F.11 SECONDARY LEADS AT HIGH FREQUENCY STARTER BOARD
TRANSFORMER
SECONDARY
LEADS
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-51
F-51
TROUBLESHOOTING & REPAIR
HIGH VOLTAGE TRANSFORMER
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
REPLACEMENT PROCEDURE
6. Replace any previously removed
cable ties.
1. Carefully position the new high volt-
age transformer in place in the two
rear mounting insulators. See Figure
F.12.
7. Replace the case wrap-around
cover.
2. Install the front mounting insulators
and mounting screw.
3. Using the phillips head screwdriver
tighten all four mounting screws mak-
ing certain the insulators are posi-
tioned correctly.
4. Reconnect the two primary leads.
5. Reconnect the two secondary leads
to the high frequency arc starter
board assembly.
FIGURE F.12 HIGH VOLTAGE TRANSFORMER MOUNTING INSULATORS
SLOTTED REAR
MOUNTING INSULATORS
NOTE: On some machines the
mounting screw configuration may be
different.
FRONT MOUNTING
INSULATORS
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-52
F-52
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-53
F-53
TROUBLESHOOTING & REPAIR
MAIN TRANSFORMER AND OUTPUT CHOKE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE
WARNING
Service and repair should be performed by only Lincoln Electric factory trained
personnel. Unauthorized repairs performed on this equipment may result in danger
to the technician or machine operator and will invalidate your factory warranty. For
your safety and to avoid electrical shock, please observe all safety notes and pre-
cautions detailed throughout this manual.
If for any reason you do not understand the test procedures or are unable to per-
form the test / repairs safely, contact the Lincoln Electric Service Department for
electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.
TEST DESCRIPTION
This procedure will aid the technician in the removal and replacement of the main
transformer and choke assembly.
MATERIALS NEEDED
3/8” Nutdriver
1/2” Wrench
Wire cutters
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-54
F-54
TROUBLESHOOTING & REPAIR
MAIN TRANSFORMER AND OUTPUT CHOKE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
REMOVAL PROCEDURE
1. Remove input power to the TIG 185
machine.
10. With the 1/2” wrench remove the X1
secondary lead from the polarity
switch. See wiring diagram. Label
lead and connection point for
reassembly.
2. Perform the SCR Bridge Assembly
Removal Procedure.
3. Unsolder the two 115VAC leads and
leads B231 and B232 from the main
transformer leads. Label leads for
reassembly. See wiring diagram.
11. With the 1/2” wrench remove the
four nuts and lock washers from the
transformer mounting bolts at the
base of the machine.
4. Unsolder leads W201 and W204
from the main transformer leads.
Label leads for reassembly. See
wiring diagram.
12. Carefully hoist the transformer/
choke assembly clear of the base.
Clear all leads.
5. Unsolder leads R209 and U210 from
the main transformer leads. Label
leads for reassembly. See wiring dia-
gram.
6. Using the 1/2” wrench remove the
shunt assembly from the choke lead.
7. With the 3/8” wrench remove the H1,
H2 or H3 lead from the input power
switch. See wiring diagram. Label
the leads and connection points for
reassembly. Cut any necessary
cable ties.
8. Remove plug J3 from the control
board and push through the interior
divider panel.
9. Using the 1/2” wrench remove the
choke lead from the polarity switch.
See wiring diagram. Label lead and
connection point for reassembly.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-55
F-55
TROUBLESHOOTING & REPAIR
MAIN TRANSFORMER AND OUTPUT CHOKE ASSEMBLY
REMOVAL AND REPLACEMENT PROCEDURE (Continued)
REPLACEMENT PROCEDURE
1. Position the new transformer/choke
assembly onto the base and mount-
ing bolts.
2. Assemble the four nuts and washers
to the mounting bolts on the base of
the machine.
3. Assemble the X1 secondary lead to
the polarity switch.
4. Assemble the choke lead to the
polarity switch.
5. Install the J3 plug into the control
board.
6. Assemble the H1, H2 or H3 lead onto
the input power switch. Insulate and
secure the unused lead (H2 or H3).
7. Assemble the shunt assembly to the
choke lead.
8. Solder leads R209 and U210 to the
main transformer leads. See wiring
diagram. Insulate connections.
9. Solder leads W201 and W204 to the
main transformer leads. See wiring
diagram. Insulate connections.
10. Solder the two 115VAC leads and
leads B231 and B232 to the main
transformer leads. See wiring dia-
gram. Insulate connections.
11. Replace any previously removed
cable ties. Clear leads and check
for “shorts” or “grounds”.
12. Perform
Assembly
Procedure.
the
SCR
Replacement
Bridge
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-56
F-56
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-57
F-57
TROUBLESHOOTING AND REPAIR
RETEST AFTER REPAIR
Should a machine under test be rejected for any reason requiring the removal of any mechanical part that could
affect the machine’s electrical characteristics, or if any electrical components are repaired or replaced, the machine
must be retested.
INPUT IDLE AMPS
Input Volts/Hertz
Maximum Idle Amps
208/60
230/60
2.50 Amps
3.00 Amps
OPEN CIRCUIT VOLTAGES
AC 70 - 80VAC
DC 55 - 65VDC
Stick Mode OCV
TIG Mode OCV
AC 70 - 80VAC
DC 60 - 70VDC
MAXIMUM ACCEPTABLE OUTPUT VOLTAGE -
AT MINIMUM OUTPUT SETTINGS
DC TIG Mode
6 Amps @ 12 Volts
MINIMUM ACCEPTABLE OUTPUT VOLTAGE -
AT MAXIMUM OUTPUT SETTINGS
DC TIG Mode
200 Amps @ 29 Volts
RECOMMENDED METERS FOR MACHINE OUTPUT TESTS
VOLTMETER: AC and DC True RMS Meter - Fluke 8922A or equivalent
AMMETER:
Columbia Type AX AC or DC Tong Ammeter
IMPORTANT: IF OTHER TYPE METERS ARE USED RESULTS MAY NOT BE ACCURATE.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
F-58
F-58
NOTES
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
Section G-1
Section G-1
TABLE OF CONTENTS
- ELECTRICAL DIAGRAMS SECTION -
Electrical Diagrams ...............................................................................................Section G
Wiring Diagram (G4549) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-2
Entire Machine Schematic (G4588) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-3
Control PC Board Schematic (G4550-1B4-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-4
Control PC Board Schematic (G4550-1B4-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-5
Control PC Board Schematic (G4550-1B4-3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-6
Control PC Board Assembly (G4551-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-7
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-2
G-2
ELECTRICAL DIAGRAMS
WIRING DIAGRAM - ENTIRE MACHINE - (G4549)
VOLTAGE RECONNECTION
SEE RATING PLATE FOR SPECIFIC VOLTAGES
230 or 400-415 or 575 VOLT CONNECTION
(AS SHOWN & AS SHIPPED FROM FACTORY)
H1 and H3 (HIGH) TO POWER SWITCH.
H2 NOT CONNECTED; INSULATE.
208 or 380 or 460 VOLT CONNECTION
380V AND ABOVE
H1 and H2 (LOW) TO POWER SWITCH.
H3 NOT CONNECTED; INSULATE.
G
CONNECT GREEN LEAD TO GROUND PER
NATIONAL AND LOCAL ELECTRICAL CODE
CONNECT BLACK AND WHITE LEADS
TO SUPPLY CIRCUIT
B
(L1)
C1 AND C2 MUST ALWAYS BE CONNECTED
ACROSS TRANSFORMER PRIMARIES
W
(L2)
C2
C1
TO GROUND PER
NATIONAL ELECTRICCODE
208V/230V ONLY
INPUT PLUG (208V/230V ONLY)
W
(L2)
H3
H2
B
(L1)
H1
S1
POWER
SWITCH
313
314
G
S4
CHOKE
245
244
A
B
C
D
E
A
B
C
D
E
F
L5
R4
R5
10K A-B
AT MINIMUM
236
P7
J7
OPTIONAL
REMOTE
AMPTROLTM
4
3
1
12
11 10
9
8
5
4
3
2
8
6
3
1
2
7
6
1
7
5
4
2
4
3
2
1
REMOTE
RECEPTACLE
231A
220A 218A
220
R3
C4
J2
J4
J3
236A
237
H3 (HIGH)
H2 (LOW)
220A
AUTO
BALANCE
LED
MODE
SWITCH
G
SCR1
H1
G1
G2
201
X3
18VAC
X4
G
R
POLARITY SWITCH MICRO SWITCH
OPEN
217
AC
TRIGGER
204
209
AC A-C, D-E, B-F
DC+ B-D, C-E, A-F, G-H
DC- B-D, A-E, C-F, G-H
260
231A
FRONT
GANG
TIG LED
AC
BALANCE
CONTROL
STICK LED
SCR2
+
CLOSED
CLOSED
240
X5
218
REAR GANG
MICRO-SWITCH
NO
NC
POWER
210
18VAC
X6
D
AC
218A
(
)
H
232
231
X8
A
312A
311A
312
311
X1
78VAC
X2
FAN
E
G
F
115VAC
X7
DIGITAL
DISPLAY
115VAC
PULSE
CONTROL
115VAC
C
S2A
DC
G3
G4
PULSE
FREQ
LED
SCR3
SCR4
B
G
216
T2
T1
1
2
W 221
R 222
216A
X2
J1
THERMAL
LED
L4
S2
POLARITY
SWITCH
Y
POS
POSTFLOW
CONTROL
(REAR VIEW,
A
C
B
1
2
3
4
5
6
SHUNT
SHOWN IN AC POSITION)
OUTPUT
CONTROL
_
(
)
J5
1
2
3
4
D
E
284
285
D1
J6
W 221
R 222
POS
CONTROL PC BOARD
L1
231
DC
GAS VALVE
235
SV1
WORK
L2
238
L3
C1,C2
BY-PASS CAPACITORS, .0047/250VAC
239
C3
HIGH VOLTAGE CAPACITOR, .0025/10kV
PHASE SHIFT CAPACITOR, 15/250VAC
BY-PASS CAPACITORS, .22/400VDC
CIRCUIT BREAKER, 10A
SPARK
GAP
C4
C5,C6
CB1
D1
ARC
STARTER
AS'BLY
C3
FREE WHEELING DIODE
284A
284B
L1
OUTPUT INDUCTOR (CHOKE)
HIGH FREQUENCY INDUCTORS
RF TOROID CHOKES
T3
COMPONENT VALUE
UNITS:
RESISTORS:
OHMS/WATTS
CAPACITORS:
MFD/VOLTS
L2,L3
L4,L5
R1,R2
R3
ELECTRODE
R2
R1
285B
LEAD COLORING CODE:
HOLDING RESISTORS, 100/100W
PHASE SHIFT RESISTOR, 200/100W
MICRO START RESISTORS, 12/100W
INPUT POWER SWITCH
B-BLACK
G-GREEN
R-RED
W-WHITE
285A
BYPASS/
STABILIZER
PC BOARD
R4,R5
S1
CONNECTOR PIN NUMBERS:
S2
POLARITY SWITCH
EXAMPLE: THIS IS PIN 7
OF CONNECTOR J4
285
S2A
MICROSWITCH ON POLARITY SWITCH
1 2 3
7
284
S4
MAIN CHOKE THERMOSTAT
SCR1,2,3,4 MAIN POWER SCR'S
14
8
J4
SV1
T1
GAS SOLENOID VALVE, 115VAC
LATCH
MAIN TRANSFORMER
VIEW OF CONNECTOR ON PC BOARD
ELECTRICAL SYMBOLS PER E1537.
T2
HIGH VOLTAGE TRANSFORMER
HIGH FREQUENCY TRANSFORMER
T3
G4549
B
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The wiring diagram specific to your code is pasted inside one of the enclosure panels of your machine.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-3
G-3
ELECTRICAL DIAGRAMS
SCHEMATIC - ENTIRE MACHINE - (G4588)
8 5 8 G 4
CHANGE DETAIL:
RELEASED FROM X A.02
ENGINEERING CONTROLLED
MANUFACTURER: No
Top rear
SEE CONNECTION DETAIL
Center of machine
Attached to Power Switch
216A
DISPLAY PRESET AT IDLE
BYPASS ASSEMBLY
C1
+15V
+5V
+24V
SCR1 GATE
G1
216
4
3
2
5J2
6J2
3J2
8J2
2J2
1J2
4J2
7J2
ACTUAL AMP WHEN WELDING
NO HOLD FUNCTION
SCR2 GATE
G2
G3
G4
G3
G2
220
G4
G3
G2
MAIN
SCR3 GATE
SCR4 GATE
15 - 20 OHM
GATE-CATHODE
SCR4
SCR3
TRANSFORMER
G4
Rear of machine attached to
base, below fan
FIRE_SCR
.0047/250VAC
3 DIGIT
METER
(DISP1)
T1
RESISTANCE TYP.
SCR3,SCR2 CATHODE
SCR1 CATHODE
SCR
218
217
216
220
MAIN SCR
RECTIFIER
H3
GATING & SNUBBER
HIGH
LOW
POWER SWITCH
+
-
SCR4 CATHODE
220A
R4
C2
D1
SCR1,SCR4 ANODE
+5V
OUTPUT CONTROL &
MODE SETTINGS ARE
MEMORIZED AT POWER
- DOWN AND RECALLED
AT POWER - UP
L1
W
12/100 EACH
R5
FREE WHEELING DIODE
G1
SCR1
H2
SCR2
X2
G1
217
1
PHASE
+15V
S1
METER
INTERFACE
BACKGROUND RESISTORS
80 VAC
X1
218
218A
BACKGROUND AC INPUT
BACKGROUND ( - )
11J3
10J3
9J3
216A
POWER-UP SEQUENCE
H1
MICRO-START
CIRCUIT
R 222(-)
W 221(+)
L2
SHUNT
400A/200mV
B
BG
IN-LINE CONNECTOR J7
Inside sleeving at top left side of
Main Rectifier
245
244
240
Right Side of SCR Bridge
Rectifier. Top of Machine
behind Choke.
METER AND MODE DISPLAY THE PREVIOUS OUTPUT
CONTROL AND MODE SETTINGS. FAN RUNS FOR 5
SECONDS. IF MODE IS TIG, GAS FLOWS FOR A TIME
SET BY THE POSTFLOW KNOB. OUTPUT IS HOT IF
MODE IS STICK. IN TIG MODE OUTPUT IS COLD UNTIL
TRIGGER IS CLOSED
BACKGROUND ( + )
+5Vref
G
RECONNECT IS DONE AT
POWER SWITCH
BACKGROUND AC INPUT
(DISABLED IN STICK)
AC
12J3
+15V
DC
Front Panel Left side
+15V
-15V
Right side of Machine
above Choke Coil.
OUTPUT
S1
L1
INDUCTOR
TOROID
VOLTAGE RECONNECTION
SEE RATING PLATE FOR SPECIFIC VOLTAGES
GangD
MODE
SHUNT (+)
SHUNT (-)
PHASE_FIRE
1J1
2J1
W 221
R 222
TOGGLE BETWEEN TIG &
STICK.
HI-FREQ, GAS, BALANCE
CONTROL, PULSE
FREQUENCY, &
GangC
TWISTED PAIRS
TYPICAL OCV
GangB
OUTPUT REGULATOR
Iarc
Gang G
CURRENT FEEDBACK
230 or 400-415 or 575 VOLT CONNECTION
65V IN DC
75V IN AC
240
+
+
SETPOINT
DC
DC
MICRO-START CIRCUIT
ARE DISABLED IN STICK
AC
+5Vref
On top of Main
Transformer
AC
CBW
(AS SHOWN & AS SHIPPED FROM FACTORY)
H1 and H3 (HIGH) TO POWER SWITCH.
H2 NOT CONNECTED; INSULATE.
-
-
DC
DC
CBW
GangA
CBW
CBW = CONNECTED
BY SWITC H
A
GangH
THESE CONNECTIONS
ARE MASE BY POLARITY
SWITCH, THEY ARE NOT
PHYSICAL LEADS
C
DETERMINE IF HI-FREQ IS
CONTINUOUS OR START
ONLY, MIN. CURRENT, AND
BALANCE CONTROL
Lower left side of
Polarity Switch
+5Vref
AC
+24V
AC
OUTPUT CONTROL
(ENCODER)
B
-
+
-
+
DC
DC
DC
DC
208 or 380 or 460 VOLT CONNECTION
METER, ENCODER, SWITCH, LEDs,
AND ALL POTENTIOMETERS ARE
MOUNTED ON PC BOARD
CBW
CBW
311
312
311
5J3
6J3
A1
5 - 185A IN DC
7 - 185A IN AC
H1 and H2 (LOW) TO POWER SWITCH.
H3 NOT CONNECTED; INSULATE.
DET_REM
Polling signal
Hi = Local
AC/DC
INTERFACE
INTERFACE
MICRO SWITCH INPUT
REM_SENSE
CLOSED
IN DC
Gang F
GangE
S2
REM_POT
Remote control
N.C.
POLARITY SWITCH
Front Panel Center
SEE CONNECTION DETAIL
+5Vref
From Auto Loc/Rem
C1 AND C2 MUST ALWAYS BE CONNECTED
ACROSS TRANSFORMER PRIMARIES
314
313
2J3
1J3
312
THERMOSTAT
THERMOSTAT INPUT
MICRO SWITCH CLOSED IN DC
OPEN IN AC
MAX. PENETRATION
DISABLE OUTPUT & HI-FREQ
IF THERMOSTAT OPEN
CW
285
284
BALANCE CONTROL IS
DISABLED IN STICK AND
DC TIG
BALANCE
R1
Inside hi-freq box on
right side of machine
near front
+5Vref
+24V
CHOKE TSTAT
10K
MAX. CLEANING
AUTO
(NORMALLY CLOSED
OPEN AT 135C TYP.)
+5Vref
BYPASS/STABILIZER
DATA
1J6
TO0 COPPER BAR
PCB
SCLK
XRES
PROGRAMMING CONNECTOR
FOR SOFTWARE UPGRADE
W 222
R 222
2J6
3J6
4J6
20 HZ
(SCHEMATIC S22530)
CW
10K
(PCB AS'BLY L10121-1)
PULSE FREQUENCY IS
DISABLED IN STICK
PULSE FREQUENCY
R2
+5Vref
ALUMINUMBAR
0.1 HZ
OFF
284A
285A
100/100
R2
+5Vref
284B
HOLDING RESISTORS
+15V
30 S
POSTFLOW
1 S
SCR
HEATSINK
CW
10K
285B
Inside hi-freq box on
right side of machine
near front
R3
In Front of main
transformer,
Attached to Base
R1
PHASE
115V CIRCUIT
TRIAC & OPTO-TRIAC
DRIVER
MICRO-
PROCESSOR
100/100
Right side of machine,
front of gas solenoid,
attached to Base
FARTHEST RIGHT SCR
TRIGGER
FARTHEST LEFT
SCR (VIEWED
FROMFRONT)
HI-FREQ OFF IN STICK
START ONLY IN DC TIG
CONTINUOUS IN AC TIG
(VIEWED FROM
FRONT)
BOTTOM
COPPER
BAR
+5V
7 GA. FLEX LEAD
Left side of Machine
near front
HIGH
VOLTAGE
TRANSFORMER
ARC STARTER ASSEMBLY
6 GA. FLEX LEADS
DC
200/100
R3
T2
LED INTERFACE
238
HI-FREQ (115VAC)
GAS (115VAC)
115VAC IN
4J4
1J4
236
235
232
260
L2
Mounted to front side
of hi-freq box on
right side of machine
near front.
C3
237
LED 1
STICK
(RED)
LED 3
TIG
(GREEN)
236B
3J4
2J4
S
12.5 OHM TYP.
C4
15/250
12KV
HIGH FREQ.
.0015/
Gang A
FAN (115VAC)
Gang D
5.5 OHMS
TYP.
14.5 KOHMS
TYP.
SPARK
GAP .020
NEXT TO MODE SWITCH
NEXT TO MODE SWITCH
T3
OUTPUT INDUCTOR
12.5 OHM TYP.
L3
TRANSFORMER
TO MICRO PROCESSOR
AND SCR GATING
115V
240
5000V
PHASE
F
285
UNUSED TERMINAL
LED 6
LED 2
THERMAL
(YELLOW)
LED 5
FREQUENCY
(GREEN)
Gang F
LED 4
AUT0BALANCE
(GREEN)
NEXT TO BALANCE POT.
OFF IN STICK AND DC TIG
Center front
Rear gang H
Gang E
THERMAL
(YELLOW)
NEXT TO METER
TWO THERMAL LEDs TO
LIGHT THROUGH
BACK-LIT THERMAL
SYMBOL
WORK
HI-FREQ CIRCUIT
Rear gang G
gang B
311
239
NEXT TO METER
NEXT TO PULSE
FREQUENCY POT.
OFF IN STICK, BLINKS AT
FREQUENCY RATE
MICRO SWITCH
PHASE
DETECTOR
X1
ELECTRODE
Right front
312
GAS
Rear Panel
Right Side
Gang C
SOLENOID
(115VAC)
+5V
GANG LOCATIONS ARE
VIEWED FROM REAR OF
SWITCH
+5V
DO NOT REVERSE LEADS
209 & 210, USED FOR SCR
PHASE TIMING
TO MICRO
PROCESSSOR
+24V
+15V
+5V
+5Vref
-15V
SV1
MOUNTING HOLE
231
235
232
209
7J3
232
X5
TRIGGER
18VAC
TRIGGER
INTERFACE
AUTO
POWER SUPPLY
CONTROL BOARD SUXP6PLY
T1
MICRO SWITCH
+15V
-15V
POLARITY SWITCH
A-C, D-E, B-F
TO MICRO
PROCESSOR
LOCAL/
REMOTE
CONTROL
8J3
210
435 OHMS TYP.
OPEN
CLOSED
CLOSED
AC
X7
B-D, C-E, A-F, G-H
B-D, A-E, C-F, G-H
DC+
DC-
AUTO LOCAL/REMOTE
T1
115VAC
STICK MODE: ALWAYS LOCAL
TIG MODE: REMOTE IF PLUGGED
LOCAL IF UNPLUGGED
FAN RUNS FOR 5 S AT POWER-UP
STOPS AT IDLE 8 MINUTES
AFTER WELDING.
115VAC
X8
12 OHMS TYP.
X3
201
18VAC
4J3
3J3
J1
2 PIN
FAN
SCR BRIDGE AND POLARITY SWITCH CONNECTION DETAIL
TRIGGER CIRCUIXT4
J2
RF
204
TYP. RPM:
1600 RPM 60Hz
1340 RPM 50Hz
260
RECEPTACLE
Left front
CHOKES
Right rear side of Main
Transformer
8 PIN
+15V
(GREEN)
COMPONENT VALUE UNITS:
AUX. WINDINGS OF
MAIN TRANSFORMER T1
LEAD COLOR CODE:
4 PIN (WHITE)
PROGRAMMING
CONNECTOR
U
N
A
B
C
D
E
F
1J5
Between SCR Bridge halves
behind choke.
B-BLACK OR GRAY
G-GREEN
O-ORANGE
R-RED OR PINK
U-BLUE
CAPACITOR: MFD/VOLTS
RESISTOR: OHMS/WATTS
Right front side of
Main Transformer
MICRO-PROCESSOR
10K
3J5
2J5
X1
MODE
J6
R
B
J3
CONNECTOR PIN NUMBERS:
EX. 12 PIN CONNECTOR
+5V
(GREEN)
OUTPUT CONTROL
SOFTWARE
VERSION LABEL
5J5
6J5
W-WHITE
Y-YELLOW
+5Vref
(GREEN)
2
1
6
W
12 PIN
J4
LABELS:
COMMON
BALANCE
7
12
LATCH
POSTFLOW
FREQUENCY
FRAME GROUND
EARTH GROUND
TOROID
J5
4 PIN
6 PIN
TM
VIEW OF CONNECTOR ON PC BOARD
OPTIONAL AMPTROL REMOTE
CONTROL AND ARC START SWITCH
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OWNED BY LINCOLN GLOBAL, INC. AND MAY NOT BE DUPLICATED, COMMUNICATED
TO OTHER PARTIES OR USED FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF LINCOLN GLOBAL, INC.
PROPRIETARY & CONFIDENTIAL:
CONTROL PCB MAIN COMPONENT & DIANOSTIC LED LAYOUT
(VIEWED FROM COMPONENT SIDE)
COMPONENT LOCATION DESCRIPTIONS ARE AS VIEWED
FROM FRONT OF MACHINE UNLESS STATED
OTHERWISE
HI-FREQ BYPASS CONNECTION
DESIGN INFORMATION
REFERENCE:
HI-FREQ BYPASS
CONNECTION
THE INFORMATION ON THIS
EQUIPMENT TYPE:
SUBJECT:
CONTROL PC BOARD
SCHEMATIC G4550-
PAGE _1__ OF ___
1
Precision Tig 185
MACHINE SCHEMATIC
FROM BOTTOM LEFT
MOUNTING HOLE TO SHEET
METAL
PRINT IS FOR REFERENCE
Front Panel Top
Jbarto
TNguyen
Approve
DRAWN BY:
ENGINEER:
APPROVED:
Reference
SCALE:
DOCUMENT
DOCUMENT
NUMBER:
ONLY. COMPONENTS AND
CIRCUITRY MAY BE DIFFERENT
FROM AN ACTUAL MACHINE.
REVISION:
ASSEMBLY G4551-
MATERIAL
DISPOSITION:
APPROVAL
DATE:
PROJECT
G4588
CRM36191
NUMBER:
A
UF
NONE
02/20/2004
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-4
G-4
ELECTRICAL DIAGRAMS
SCHEMATIC - CONTROL PC BOARD - (G4550-1B4-1)
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-5
G-5
ELECTRICAL DIAGRAMS
SCHEMATIC - CONTROL P.C. BOARD - (G4550-1B4-2)
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-6
G-6
ELECTRICAL DIAGRAMS
SCHEMATIC - CONTROL P.C. BOARD - (G4550-1B4-3)
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
G-7
G-7
ELECTRICAL DIAGRAMS
PC BOARD ASSEMBLY - CONTROL - (G4551-1)
1
5 5 1 - G 4
CHANGE DETAIL:REVISED IDENTIFICATION CODE, SCHEMATIC REFERENCE, BUY PART NUMBER AND ITEM 40.
EMNAGNIUNFEAECRTINUGRECRO:NYTResOLLED
ITEM
PART NO.
G4551-B
S25864-4
E2861
DESCRIPTION
53 R4,R49-R50,R68-
R69,R72,R107,R122,R1
32,R162,R184
54 R5,R16-R17,R30-
R32,R51,R60-
11 S25000-1002SMT
15 S25000-1001SMT
RESISTOR,SMD,METAL FILM,1/10W,10.0K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,1.00K,1%,S0805
REQ
1
1
1
2
3
PRECISION TIG 185 CONTROL PCB BLANK
PSOC SOFTWARE
SEALANT
N.C., N.D.
N.C.,N.D.
N.J.
N.C.
N.C.
N.F.
AS NEEDED
FOR ITEMS BELOW, REFER TO ELECTRONIC COMPONENTS DATABASE FOR CURRENT SPECIFICATIONS
R61,R92,R194-
R195,R208,R212,R215
55 R6
56 R7,R9,R111-
R113,R135,R143,R145,
R147,R149,R191,R196-
R198,R200,R202
ITEM REFERENCES
QTY PART NUMBER
M17789-4
21 S25020-2SMT
DESCRIPTION
4
5
A1
1
ENCODER,INCREMENTAL,2-BIT,PEC12
CAPACITOR,SMD,CERAMIC,0.022MF,50V,10%,X7R,S0805
1
S25000-1500SMT
RESISTOR,SMD,METAL FILM,1/10W,150OHMS,1%,S0805
RESISTOR,SMD,1K,1/4W,1206,1%,TR
C1,C3,C29,C39,C41-
C43,C58,C60,C78,C84,
C89-C92,C94-C95,C103-
C104,C109-C110
16 S25001-1001SMT
57 R8,R34,R203
58 R10-R11,R52-R53,R90-
R91,R103-R104
59 R12-R15,R26-R29,R42- 16 S25003-1210SMT
R45,R55-R58
3
8
S25000-6812SMT
S25004-1R00SMT
RESISTOR,SMD,METAL FILM,1/10W,68.1K,1%,S0805
RESISTOR,SMD,1W,1.00OHMS,1%
6
7
8
9
C2,C10,C35,C111
C4,C23,C38
C5,C20,C45
C6-C7,C9,C12,C17-
C18,C24,C30-
4
3
3
S25020-9SMT
S25024-2SMT
S25020-12SMT
CAPACITOR,SMD,CERAMIC,47pF,50V,5%,COG,S0805
CAPACITOR,SMD,TANTALUM,1.0MF,35V,10%,S3528
CAPACITOR,SMD,CERAMIC,100pF,100V,5%,COG,S0805
CAPACITOR,SMD,CERAMIC,4700pF,50V,10%,XR7,S0805
RESISTOR,SMD,1W,121OHMS,1%
14 S25020-10SMT
60 R18
61 R19,R64,R157,R160,R1
65,R170
62 R20,R36,R41,R54
63 R21
64 R22
1
6
S25000-5622SMT
S25001-47R5SMT
RESISTOR,SMD,METAL FILM,1/10W,56.2K,1%,S0805
RESISTOR,SMD,47.5OHMS,1/4W,1206,1%,TR
C32,C34,C44,C53,C59
10 C8,C13,C25-C26
11 C11,C14,C19,C21-
C22,C33,C48,C50-
C52,C55-
C56,C62,C64,C66,C68,
C74-C76,C79-
4
S20500-17
CAPACITOR,PPMF,0.1MF,630V,5%,BOX
CAPACITOR,SMD,CERAMIC,0.1MF,50V,10%,X7R,S0805
DISP1
LED2
LED6
X X X X X
X
X
X
X
LED1
X
X
X
X
32 S25020-3SMT
4
1
1
2
1
2
2
6
S25003-15R0SMT
S25000-7681SMT
S25000-4752SMT
S25000-2213SMT
S25001-2210SMT
S25006-10R0SMT
S25008-1002SMT
S25001-1000SMT
RESISTOR,SMD,1W,15.0OHMS,1%
S1
RESISTOR,SMD,METAL FILM,1/10W,7.68K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,47.5K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,221K,1%,S0805
RESISTOR,SMD,221OHMS,1/4W,1206,1%,TR
RESISTOR,SMD,METAL_FILM,1/2W,10OHMS,1%,S2010
RESISTOR,SMD,PREC,MF,1/10W,10.0K,0.5%,S0805
RESISTOR,SMD,100OHMS,1/4W,1206,1%,TR
A1
X X X X X
65 R23,R79
66 R24
C83,C85,C93,C98,C100
,C105,C107-C108,C112
LED3
67 R25,R75
68 R33,R38
69 R35,R84,R108-
R109,R139,R166
70 R37,R85,R106
71 R39,R81-
R82,R98,R128,R131,R1
67,R177,R182,R185,R1
87-R188,R210-R211
72 R40,R46-R47,R73-
R74,R76-R77,R86,R96-
R97,R141-R142,R179-
R180
12 C15,C63
2
3
3
1
2
1
9
S25020-4SMT
S25020-14SMT
S25020-7SMT
S25020-24SMT
S13490-199
CAPACITOR,SMD,CERAMIC,820pF,50V,5%,COG,S0805
CAPACITOR,SMD,CERAMIC,330pF,100V,5%,COG,S0805
CAPACITOR,SMD,CERAMIC,0.22MF,50V,20%,X7R,S1812
CAPACITOR,SMD,CERAMIC,1.0MF,25V,10% ,X7R,S1206
CAPACITOR,ALEL,220,25V,20%,LOW-ESR
13 C16,C40,C113
14 C27,C36-C37
15 C28
16 C46,C49
17 C47
18 C54,C69-
C70,C73,C86,C96,C99,
C101,C106
19 C57,C61,C65
20 C67,C77
21 C71-C72,C87-C88,C102
3
S25000-3322SMT
RESISTOR,SMD,METAL FILM,1/10W,33.2K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,4.75K,1%,S0805
14 S25000-4751SMT
S13490-179
T11577-52
CAPACITOR,ALEL,1000,35V,20%
CAPACITOR,CD,.0047/.005,1400V,20%
14 S25001-4751SMT
RESISTOR,SMD,4.75K,1/4W,1206,1%,TR
X X X X X X
X
X
X
X
X X X X X X
X X X X X X
R2
R1
R3
X
3
2
5
S13490-197
S25020-5SMT
T11577-58
CAPACITOR,ALEL,82,35V,20%,LOW-ESR
CAPACITOR,SMD,CERAMIC,2700pF,50V,5%,X7R,S0805
CAPACITOR,CD,.0047,3000V,20%
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
73 R48,R199,R209,R213-
R214
5
S25000-2210SMT
RESISTOR,SMD,METAL FILM,1/10W,221OHMS,1%,S0805
74 R59,R136
75 R62
76 R63,R120
77 R65-R66,R94-
R95,R130,R137
78 R67
79 R70,R117,R119,R121,R
204
80 R71
2
1
2
6
S25000-4750SMT
S25000-1000SMT
S25000-8251SMT
S25008-4751SMT
RESISTOR,SMD,METAL FILM,1/10W,475OHMS,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,100OHMS,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,8.25K,1%,S0805
RESISTOR,SMD,PREC,MF,1/10W,4.75K,0.5%,S0805
22 C97
23 DISP1
1
1
3
2
1
2
2
8
S13490-181
S17395-11
CAP,ALEL,22,63V,20%
LED,DISPLAY,7-SEGMENT,CC,3-DIGIT
ZENER DIODE,SMD,0.5W,12V,5%,SOD-123
ZENER DIODE,SMD,0.5W,18V, 5%,SOD123
ZENER DIODE,SMD,0.5W,5.1V, 5%,SOD123
ZENER_DIODE,SMD,225mW,12V,5%,SOT-23
ZENER DIODE,SMD,3W,12V,5%, SMB
DIODE,SMD,1A,400V,FAST RECOVERY,DO-214BA
LED4
X
X
X
X
X
X
24 DZ1,DZ8,DZ10
25 DZ2-DZ3
26 DZ4
27 DZ5-DZ6
28 DZ7,DZ9
29 D1-D3,D5,D7-D8,D21-
D22
30 D4,D6,D16,D18-
D20,D28,D31-
D32,D35,D40-D41
31 D9-D15,D17,D23,D29-
D30,D33-D34,D36-D39
32 D24-D27
33 J1
34 J2
35 J3
36 J4
37 J5
38 J6
39 LED1
40 LED2,LED6
41 LED3-LED5
42 LED7-LED9
43 L1-L5
S25046-4SMT
S25046-3SMT
S25046-1SMT
S25045-1SMT
S25044-3SMT
S25040-1SMT
X X X X X
X X X X X
X X X X X
LED5
1
5
S25000-1003SMT
S25000-3321SMT
RESISTOR,SMD,METAL FILM,1/10W,100K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,3.32K,1%,S0805
1
1
2
S25000-1004SMT
S25001-1002SMT
S25000-1212SMT
RESISTOR,SMD,METAL FILM,1/10W,1.00M,1%,S0805
RESISTOR,SMD,10K,1/4W,1206,1%,TR
RESISTOR,SMD,METAL FILM,1/10W,12.1K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,47.5OHMS,1%,S0805
N.C.
N.C., N.D., N.H. (3 PLACES)
N.E.
81 R78
12 S25040-5SMT
17 S25040-2SMT
DIODE,SMD,DUAL,0.200A,70V,UFR
DIODE,SMD,1A,400V,DO-214BA/AC
82 R80,R83
83 R87-R89,R99-
R102,R205-R207
84 R93
85 R105,R110
86 R114,R216
87 R115
88 R116,R153-R154
89 R118
90 R123,R133
91 R124-
R125,R127,R171,R181,
R189
92 R126,R138
93 R129
94 R134
95 R140
96 R144,R146,R148,R150,
R186,R190,R192-R193
97 R151-R152,R155-
R156,R158-R159,R163-
R164,R168-R169,R175-
R176
98 R161
99 R172-R174,R178
100 R183
101 R201
102 S1
103 TP1-TP7
104 TRI1,TRI3
105 TRI2,TRI4
106 T1-T2
10 S25000-47R5SMT
OPPOSITE COMPONENT SIDE
1
2
2
1
3
1
2
6
S25000-2671SMT
S25003-47R5SMT
S25000-6811SMT
S25000-2212SMT
S25003-2002SMT
S25001-4752SMT
S25000-2211SMT
S25003-2000SMT
RESISTOR,SMD,METAL FILM,1/10W,2.67K,1%,S0805
RESISTOR,SMD,1W,47.5OHMS,1%
RESISTOR,SMD,METAL FILM,1/10W,6.81K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,22.1K,1%,S0805
RESISTOR,SMD,1W,20.0K,1%
RESISTOR,SMD,47.5K,1/4W,1206,1%,TR
RESISTOR,SMD,METAL FILM,1/10W,2.21K,1%,S0805
RESISTOR,SMD,1W,200OHMS,1%
4
1
1
1
1
1
1
1
2
3
3
5
1
4
3
1
4
2
S25040-10SMT
S24020-2G
S24020-8
S24020-12
S24020-4
S24020-6
S18248-4
T13657-2
T13657-14
T13657-3
DIODE,SMD,3A,400V,D0-214AB
CONNECTOR,MOLEX,MINI,PCB,2-PIN,GOLD
CONNECTOR,MOLEX,MINI,PCB,8-PIN,TIN
CONNECTOR,MOLEX,MINI,PCB,12-PIN,TIN
CONNECTOR,MOLEX,MINI,PCB,4-PIN,TIN
CONNECTOR,MOLEX,MINI,PCB,6-PIN,TIN
CONNECTOR,MOLEX,MINI,PCB,4-PIN
LED,T-1,3/4,RED,HLMP-3003
LED,T-1,3/4,AMBER,HIGH-INTENSITY
LED,T-1,3/4,GREEN,HLMP-3502
LED,SMD,GREEN,CLEAR,S1206
CHOKE,RF,390UH,5%, 225MA,CONFORMAL
MOV,150VRMS,80J,20MM
MOV,130VRMS,90J,20MM
MOV,320VRMS,150J,20MM
IC,SMD,OPTOCOUPLER,HMA124
1
N.C.
N.K.
5.01
2
1
1
1
8
S25001-1213SMT
S25000-2001SMT
S25000-6813SMT
S25000-3323SMT
S25001-2670SMT
RESISTOR,SMD,121K,1/4W,1206,1%,TR
6.00
RESISTOR,SMD,METAL FILM,1/10W,2.00K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,681K,1%,S0805
RESISTOR,SMD,METAL FILM,1/10W,332K,1%,S0805
RESISTOR,SMD,267OHMS,1/4W,1206,1%,TR
S25080-2SMT
T12218-9
D2
5.83
R10
J1
C7
R19
R20
44 MOV1
T13640-16
T13640-25
T13640-18
S15000-34SMT
S15000-16
S25051-11SMT
T1
45 MOV2-MOV5
46 MOV6-MOV8
47 OCI1
48 OCI2-OCI5
49 Q1,Q6
50 Q2-Q3,Q5,Q7,Q9-
Q10,Q12-Q13,Q15-Q18
51 Q4,Q8,Q11,Q14
52 R1-R3
D3
X2
N.A.
Q2
D4
PT185
R35
R36
12 S25001-1821SMT
RESISTOR,SMD,1.82K,1/4W,1206,1%,TR
CONTROL
5.13
C20
OPTOCOUPLER,TRIAC,DRIVER,ZVC,3083
TRANSISTOR,SMD,NMF,DPAK,TO-252,48A,100V(SS)
TRANSISTOR,SMD,NPN,0.5A,40V,SOT-23,MMBT4401LT1
R41
D5
R40
R47
D40
R46
X3
MOV4
TP4
12 S25050-1SMT
TP1
TP2
T2
D6
X4
R52
R54
1
4
1
1
1
7
2
2
2
1
1
3
1
1
1
1
1
1
1
1
1
S25001-7500SMT
S25001-1211SMT
S25000-1502SMT
S25001-2211SMT
T13381-16
TESTPT_FUNTIONAL FUNCTIONAL TEST POINT
S18395-27
S15161-27
T12737-2
S25073-3SMT
S15128-27SMT
S15128-28SMT
S18395-8
S15128-10SMT
M15102-4SMT
S15128-5SMT
S25072-2SMT
S15018-21SMT
S17900-24SMT
S25065-3SMT
S15018-11SMT
RESISTOR,SMD,750OHMS,1/4W,1206,1%,TR
RESISTOR,SMD,1.21K,1/4W,1206,1%,TR
RESISTOR,SMD,METAL FILM,1/10W,15.0K,1%,S0805
RESISTOR,SMD,2.21K,1/4W,1206,1%,TR
N.K.
MOV5
D12
C31
R64
4
3
S25050-2SMT
T10812-116
TRANSISTOR,SMS,PNP,SOT23,0.5A, 40V,MMBT4403LT1
POT,SINGLE-TURN,0.25W,10K,10%
D8
D13
R73
R76
R74
R77
D41
R72
D9
D10
Q7
SWITCH,PUSHBUTTON,SPST,GREEN,W/BLACK EXTENDER
N.B.
D15
D16
TP3
R92
R93
TRIAC,T220,8A,800V,WITH S18104-3HS
TRIAC,T220,8A,800V
TRANSFORMER,PULSE,3-WINDING,1:1:1
IC,SMD,CMOS,PSOC,8-BIT,CY8C26643,TQFP44(SS)
IC,OP-AMP,SINGLE,PRECISION,LT1097S8
IC,OP-AMP,SMT,QUAD,HIGH-PERF,33074ADT
REGULATOR,HEAT-SINKASBLY,S15128-6,S18104-3
IC,SMD,VOLTAGE REF,ADJ, PRECISION,431I,SOIC-8
IC,ARRAY,DRIVER,PERIPHERAL,NPN,DARLINGTON
IC,VOLT REG,SMD,FIXED,3-T,(+),1A,5V
IC,SMD,ACT,BUFFER,OCTAL,3-STATE,TSSOP-20(SS)
IC,SMD,CMOS,DRIVER,MOSFET,4451, SOIC-8(SS)
IC,SMD,CMOS,GATE,NAND,2-INPUT,QUAD,SCHM(SS)
IC,SMD,CMOS,INVERTER,SCHMITT,HEX,VHC14(SS)
IC,SMD,CMOS,SWITCH,ANALOG,QUAD,201(SS)
C47
Q10
R199
C48
C46
R94
R95
R205
X1
CAPACITORS = MFD / VOLTS
RESISTORS = OHMS
R206
C50
R213
N.A.,N.B.
N.A.
X6
C51
C49
R105
R110
107 X1
108 X2
109 X3-X4,X14
110 X5
111 X6
112 X7
113 X8
114 X9
115 X10
N.G.
X7
R207
C54
Q11
Q13
X9
X10
Q12
D20
DZ5
D23
NOTES:
N.A.
R214
X11
X12
R116
THIS DEVICE IS SUBJECT TO DAMAGE BY STATIC ELECTRICITY, SEE E2454 BEFORE
HANDLING.
PROGRAM X1 WITH ITEM 2.
KEEP FREE OF ENCAPSULATION MATERIAL.
SEAL COMPONENT BY APPLYING ITEM3 AS SHOWN SO THAT ENCAPSULATION MATERIAL
DOES NOT GET INSIDE COMPONENT.
KEEP FREE OF ENCAPSULATION MATERIAL (.50 DIA. MIN.) ON BOTH SIDES OF BOARD.
KEEP MOUNTING HOLES FREE OF ENCAPSULATION MATERIAL (5 PLACES).
COVER MOLEX WITH TAPE.
HAND TIGHT MOUNTING WASHER AND MOUNTING NUT TO POTENTIOMETER BUSHING.
WHEN ASSEMBLING DISPLAY, SPACE DISPLAY OFF THE BOARD .125+/- .010 MEASURED
FROM BOTTOM OF DISPLAY TO PC BOARD SURFACE.
TP5
C68
C69
TP7
N.B.
N.C.
N.D.
D28
X13
X14
C70
C73
C86
TRI2
TRI4
116 X11
117 X12
118 X13
D31
TRI1
TRI3
N.E.
N.F.
N.G.
N.H.
N.J.
DZ6
R141
R142
N.K.
OCI1
D32
C94
Q14
Q15
R151
R155
R158
R163
R168
R175
R179
R152
R156
R159
R164
R169
R176
R180
R160
C96
C99
C95
BUY AS:
R157
R165
Q16
D35
R161
OCI2
OCI3
OCI4
OCI5
N.K.
SQUEEZE COMPONENTS TOGETHER BEFORE ENCAPSULATION.
G 4
5
5
1
-
1
B
4
Q17
C101
DZ10
PART NUMBER IDENTIFICATION CODE
C106
BUY PER E3867
TEST PER E4127-C
D36
D38
D37
D39
N.K.
ENCAPSULATE WITH HUMISEAL (2 COATS)
1A27LU PER E1844 OR WITH EQUIVALENT AS
APPROVED BY LINCOLN ELECTRIC CO.
.23
0
TP6
P.C. BOARD BLANK REFERENCE INFORMATION
BUY COMPLETE AS G4551-B
SEE ELECTRONIC FILE FOR INFORMATION
N.K.
8.81
SCHEMATIC REFERENCE G4550-1B4
.21
0
9.00
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OWNED BY LINCOLN GLOBAL, INC. AND MAY NOT BE DUPLICATED, COMMUNICATED
TO OTHER PARTIES OR USED FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF LINCOLN GLOBAL, INC.
PROPRIETARY & CONFIDENTIAL:
COMPONENT SIDE
UNLESS OTHERWISE SPECIFIED TOLERANCE
MANUFACTURING TOLERANCE PER E2056
ON 2 PLACE DECIMALS IS ± .02
DESIGN INFORMATION
jbarto
REFERENCE:
G4407-1
SCALE:
EQUIPMENT TYPE:
SUBJECT:
PAGE _1__ OF ___
1
PRECISION TIG 185
DRAWN BY:
ON
3
PLACE DECIMALS IS ± .002
DOCUMENT
DOCUMENT
NUMBER:
ON ALL ANGLES IS ± .5 OF A DEGREE
CONTROL PC BOARD ASSEMBLY
REVISION:
MATERIAL TOLERANCE (" ") TO AGREE
t
ENGINEER: Trang Nguyen
APPROVED:
WITH PUBLISHED STANDARDS.
MATERIAL
APPROVAL
PROJECT
NUMBER:
G4551-1
CRM37680
D
UF
-
1:1.25
11/29/2005
DISPOSITION:
DATE:
DO NOT SCALE THIS DRAWING
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty. Individual Printed Circuit Board Components are not available from Lincoln Electric. This information is pro-
vided for reference only. Lincoln Electric discourages board level troubleshooting and repair since it may compromise the quality of the design and may result in danger to the Machine Operator or Technician. Improper PC board repairs could result in damage to the
machine.
PRECISION TIG 185
Download from Www.Somanuals.com. All Manuals Search And Download.
SVM ERROR REPORTING FORM
We need to know if there are errors in our manuals. We also value any suggestions as to
additional tests or procedures that would make this SVM a better tool for you.
If you discover new or different “Problems or Symptoms” that are not covered in the three col-
umn troubleshooting chart, please share this information with us. Please include the
machine’s code number and how the problem was resolved.
Thank You,
Technical Services Group
Lincoln Electric Co.
22801 St. Clair Ave.
Cleveland, Ohio 44117-1199
FAX 216-481-2309
SVM Number ___________________________
Page Number if necessary__________________
Your Company__________________________
Your Name_____________________________
Please give detailed description below:
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
SD287 04/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Learning Resources Handheld Game System LER 6960 User Manual
Lenoxx Electronics CD Player BP 103 User Manual
Life Fitness Home Gym FZTR User Manual
Lincoln Electric Water Pump IM818 User Manual
Lucent Technologies Network Card 40H CES User Manual
Lux Products Thermostat T10 1143 PSM40 User Manual
Marshall electronic Microphone MXL 860 User Manual
MartinLogan Portable Speaker Loudspeaker Systems User Manual
Maverick Ventures Meat Grinder MM 5501 User Manual
Melissa Vacuum Cleaner 240 014 User Manual