®
COMPACT DISC PLAYER
AM/FM/TV1/TV2 (WEATHER) BAND STEREO CASSETTE RECORDER
MODEL CD-103/BP-103
OPERATING INSTRUCTIONS
PLAYS MUSIC COMPACT DISCS
•
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
•
RECEIVES TV BAND AND WEATHER BAND
•
RECEIVES AM/FM BROADCASTS
•
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
•
FM STEREO AND POWER LED INDICATORS
•
2 WAY POWER - AC/DC
•
REQUIRES 6 SIZE “C” BATTERIES (not included)
•
PLEASE READ CAREFULLY BEFORE USE
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY INSTRUCTIONS
1. Power Sources - The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
2. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.
3. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
4. Servicing - The user should not attempt to service the appliance beyond that described in
the operating instructions. All other servicing should be referred to qualified service personnel.
It is the intent of Lenoxx that this product be used in full compliance with the
copyright laws of the United States and that prior permission be obtained from
copyright owners whenever recording songs from the RADIO or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
on the bottom of the set.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
2
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
manual (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you can’t resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
AC SOCKET
To a wall outlet
NOTE: One blade of plug
and outlet is wider.
Battery compartment
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord into
the socket located at the rear of the player, and the
other end to the wall outlet.
Tip
If the plug of the AC power
cord does not match your
outlet, do not force it.
•
Reverse it and try again.
This plug is polarized and
only fits one way into the
wall outlet and the back of
the set.
2. Using the player on batteries
Insert 6 size “C” batteries (not supplied) into the
battery compartment.
Replace the batteries when
•
To use the player on batteries, disconnect the AC
power cord from the player.
the Power Lamp dims or
when the player stops
operating. Replace all the
batteries with new ones.
Before you replace the
batteries, be sure to take
out the CD from the player and
remember to check the
Battery Safety Instructions
on Page 3.
If the CD does not play
•
on batteries, this means
the batteries are almost
used up. But the radio may
continue to play on these
weak batteries because it
uses less power than the CD
player.
4
IB-CD103(SY)-WM-E-090402
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A CD
2 & 3
1
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION
switch to CD position
POWER
lamp
1
2
(power on), the POWER
lamp will be on. And the
display will show 2 dashes
“
“
” flashing , then
”.
Lift the right corner of the
CD DOOR to open it and
place the CD in the CD
compartment. The label
side of the CD should face
upward.
Close the CD DOOR by
pushing it down. The
display will show the total
tracks on that CD.
POWER
lamp
3
4
Press the CD PLAY
button. The POWER and
PLAY lamps will be steady
on, the player plays all
the tracks once.
PLAY/PAUSE
PLAY lamp
Track
number
5
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
OPEN THE CD DOOR
BY LIFTING HERE
FUNCTION SWITCH
VOLUME CONTROL
PLAY/PAUSE
STOP
Track number
TIP
FORWARD
BACKWARD
When CD play is
paused, the PLAY/
PAUSE lamp will
flash and no music
will play.
To
Press or Adjust
Adjust the volume
Stop playback
VOLUME control
STOP
To resume play,
press the PAUSE
button again, the
PLAY lamp will stop
flashing and music
will play.
PLAY/PAUSE
The PLAY lamp will flash
during pause. Press again
to resume play after pause.
Pause playback
Go to the next track
FORWARD
BACKWARD
TIP
If you bump the set
during CD play, the
music will stop or
Go back to the previous
track
BACKWARD
FORWARD
Press and hold down while
playing until you find the
point.
or
skip for
a
few
seconds. This is
normal for this type
of player.
Locate a point in a song
Lift the CD DOOR (press
STOP first).
Remove the CD
Slide the FUNCTION switch
to TAPE position.
Turn off the power
6
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO THE RADIO
2
1
3
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION switch to RADIO
position, the POWER lamp will be on.
1
2
Slide the BAND switch to the proper band
position (AM, FM, or TV1, TV2 (WEATHER
BAND)) that you want.
Select AM to tune AM radio stations.
Select FM to tune FM radio stations.
Select TV1 to tune TV channels 2 through 6.
Select TV2 to tune TV channels 7 through 13,
including WEATHER BAND.
WEATHER
3
T
U
N
I
N
G
Tune into the station you prefer using the
TUNING control (at the right side of the set).
Adjust for the clearest sound.
NOTE 1: When tuning to TV band stations, many times a loud
buzzing will be heard, which results from the video portion
of the TV signal. This is normal for all TV band radios.
NOTE 2: TV band and Weather Band signals are weaker than
normal FM signals. Most TV band signals have a range
of only 50 miles (maximum) from the broadcast station.
NOTE 3: Some noise or 2 way radio conversations may be heard
on the TV band or Weather Band, this is normal and
results from the weaker signals of these broadcasts.
WB may not be received in all areas due to a lack of
transmission coverage for those areas or in some fringe
areas where TV signals can only be received by using
Cable.
4
POWER
FM
STEREO
The FM STEREO indicator will light up when
receiving FM Stereo broadcasts.
7
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
FUNCTION SWITCH
VOLUME
CONTROL
TIP
To
Slide or Adjust
Next time you want to
•
listen to the radio, just
slide the FUNCTION
switch to RADIO.The
player automatically
starts playing the pre-
viously tuned station.
VOLUME control
Adjust the volume
Slide the FUNCTION
switch to TAPE position
Turn off the Radio
To improve broadcast reception
Change position of the antenna for FM,TV1 or TV2
(WEATHER BAND). Move the set itself for AM.
8
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A TAPE
3
2
1
Connect the supplied AC power cord or batteries (see page 4).
TAPE PLAY DIRECTION
Slide the FUNCTION
switch to TAPE position.
1
A
EMPTY
REEL
FULL
REEL
Press the STOP/EJECT
button to open the tape
compartment and insert
a recorded tape. Close
the door.
STOP/EJECT
2
/
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
PLAY
Press the PLAY button.
The player turns on and
starts playing.
3
4
OK
NO
When the set finishes
playing this side of the
tape, the set will stop. To
hear the other side of the
tape, flip the tape over,
then reinsert and press
PLAY.
AUTO STOP
OK
NO
9
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
VOLUME CONTROL
MICROPHONE
PHONES JACK
PAUSE STOP/EJECT
PLAY
FAST F.&REWIND
To
Press or Adjust
Adjust the volume
Stop playback
VOLUME control
STOP/EJECT button
Fast forward or rewind
the tape
FAST FORWARD button or
REWIND button
PAUSE button
Press again to resume play after
pause.
Pause playback
Eject the cassette
STOP/EJECT button
To enjoy the music
without disturbing others
Insert your headphone plug into
the PHONES jack.
Make sure cassette buttons are
all up (stop) and FUNCTION switch
is in the center position (power
off).
To shut power off
10
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING ON A TAPE
1
3
Connect the supplied AC power cord or batteries (see page 4).
Press the STOP/EJECT button to
STOP/EJECT
TAPE PLAY DIRECTION
open the tape compartment and
insert a blank tape. Select the
program source (AM, FM, TV1,
TV2, CD, or, built-in microphone)
you want to record.
1
2
/
A
EMPTY
REEL
FULL
REEL
To record from the CD player, insert
a CD and follow the steps to play a
CD (see page 5).
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
To record from the radio, slide the
FUNCTION switch to RADIO, and
tune into the station you want (see
page 7).
To record from the built-in
microphone, leave the FUNCTION
switch at the TAPE position, and
speak in front of the set.
RECORD
Press the RECORD button to start
recording. (The PLAY button is
depressed automatically.)
3
4
OK
NO
REWIND PLAY
To hear what you recorded, slide
the FUNCTION switch to TAPE
position, then press REWIND and
PLAY.
OK
NO
11
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
FUNCTION SWITCH
TIP
• For best recording
effect, use the AC
power instead of
batteries.
STOP/EJECT
PAUSE
Press or Adjust
To
• To
erase
a
recording, just start
a new recording,
and the old one is
a u t o m a t i c a l l y
replaced.
Stop recording
STOP/EJECT button
PAUSE button
Press the button again to
resume recording.
Pause recording
Press the STOP/EJECT
button and slide the
FUNCTION switch to TAPE
position.
Turn off the power
12
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING CD TRACKS REPEATEDLY
(REPEAT PLAY)
You can play CD tracks over and over in normal or program play modes (see page
14).
FUNCTION SWITCH
REPEAT BUTTON
PROGRAM BUTTON
1. Slide the FUNCTION switch to CD position.
2. Select the track by pressing
or
, and then press
.
3. Press the CD REPEAT button.
To repeat
Press
Display shows
PLAY/
PAUSE
PROGRAM
Press the REPEAT button
once, the REPEAT lamp will
flash.
a single track (song)
REPEAT
PLAY/
PAUSE
PROGRAM
Press the REPEAT button
twice, the REPEAT lamp will
be steady on.
all the tracks (all songs)
programmed tracks
REPEAT
During programmed play,
press the REPEAT button
twice, both the REPEAT and
PROGRAM lamps will be
steady on.
PLAY/
PAUSE
PROGRAM
REPEAT
To cancel Repeat Play
Press the REPEAT button until the REPEAT lamp goes off.
13
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING CD TRACKS IN PROGRAMMED ORDER
Programmed Play
You can make a program of up to 16
tracks in the order you want them to be
played.
PROGRAM
1. Slide the FUNCTION switch to CD position.
Make sure the CD is stopped.
PLAY/
PAUSE
2. Press the PROGRAM button. The letters
PROGRAM
“
” and the PROGRAM lamp will flash.
REPEAT
3. Press or to select the tracks you want to
program in the order you want.
4. Press the PROGRAM button to confirm.
The letters “
” will flash and the PROGRAM
lamp will be steady on.
5. Repeat steps 3 and 4. You can program up to 16
tracks.
6. Press
to start programmed play. During the
PLAY/
PAUSE
PROGRAM
programmed play, the selected track numbers
will display in the programmed order.
REPEAT
The PLAY and PROGRAM lamps will be steady
on.
To change the current program
Just create a new program following the Programming procedure.
To cancel Programmed Play
Press the STOP button twice or slide the FUNCTION switch to
TAPE position (POWER OFF).
14
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
On Safety
On Power Sources
For battery operation, use 6 size “C”
As the laser beam used in the CD
•
•
batteries. We recommend alkaline
batteries for longer life.
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet. Refer servicing to
qualified personnel only.
When the batteries will not be used
•
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage or corrosion.
Should any solid object or liquid fall
•
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
On Operation
On Placement
If the player is brought directly from a
•
Do not leave the player in a location
•
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate. If the player has not been
used for a long time, set it in the
playback mode to warm it up for a few
minutes before inserting a cassette.
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
Do not place the player on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
prolong the life of its components.
This CD player is designed to be
•
If the player is left in a car parked in
•
played on
a
stable no vibration
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the
sun.
position. If you bump the set during
CD play, the music will stop or skip for
a few seconds. This is normal for this
type of player.
Since a strong magnet is used for the
•
If you have any questions or problems
concerning your player, please contact
our customer service department at
1-800-315-5885.
(Monday - Thursday 09:00 AM - 05:00 PM,
Friday 09:00 AM - 01:00 PM EST)
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the player to
prevent possible damage from the
magnets.
•
15
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS (continued)
Notes on CDs
Notes on Cassettes
Before playing, clean the CD with a
•
Break off the cassette tab from side A
•
cleaning cloth. Wipe the CD from the
center out.
or B to prevent accidental recording.
Side A
Tab for side A
Tab for side B
Do not use solvents such as benzene,
•
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
Do not expose the CD to direct
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
Use of a cassette with more than
•
90 minutes, such as C-120 (120
minutes), is not recommended.
The extreme thinness of this tape
may damage this set.
Do not stick paper or stickers on the
CD, nor scratch the CD.
•
To reduce the chances of tape
•
jamming or tangling, you should check
that there are no loose layers of tape
visible through the cassette center
window. If any, tighten these loose
layers of tape using a pencil before
inserting the cassette into the set.
After playing, store the CD in its case.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
16
IB-CD103(SY)-WM-E-090402
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning the Lens
Notes for Storing
Cassette Tapes
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner and blower.
1. Do not put a tape near a magnetic
field, such as a TV, or speaker.
Magnetic fields may reduce the tape
sensitivity or even erase the
recording.
2. Do not store tape for any length of
time in a hot, moist or dusty place.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and
the capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, insert a tape when the
areas cleaned are completely dry.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzene.
RECORD/PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
ADVICE
PROTECT YOUR FINE FURNITURE
WE RECOMMEND A CLOTH OR OTHER
PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT
ON SURFACE WITH A NATURAL OR
LACQUER FINISH.
CAPSTAN
COTTON SWAB
NOTE: In order to see and clean the
head, you may have to press
PLAY first.
17
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Remedy
Problem
Connect the AC power cord to a wall outlet
securely.
Make sure the batteries are inserted
•
•
The power is not on.
correctly and they are fresh.
Make sure the FUNCTION switch is in the correct
position.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening through
speakers.
•
•
Make sure that the CD compartment is closed.
Place the CD with the label side up.
Clean the CD.
Take out the CD and leave the CD DOOR open for
about an hour to dry moisture condensation.
Make sure the FUNCTION switch is at CD
position.
•
•
•
•
CD does not play.
•
Clean the CD, or replace it if the CD is badly
damaged.
Place the player in a location free from
vibration.
•
•
The sound drops out.
Check if your batteries are fresh.
•
•
CD does not play while radio may
continue to play.
It is normal since the radio uses less power than
the CD player.
Replace all the batteries with new ones if they are
weak, or bring the set near a window, or rotate the
set.
The sound is weak or has poor
quality.
•
Adjust the length and the angle of the antenna to
change position for better reception.
The reception of FM/TV/WB band
is weak.
•
Make sure the recording tab on the cassette is in
place.
Make sure the FUNCTION switch is in the correct
•
•
•
The tape does not play or record
position.
Make sure the tape is inserted correctly.
Clean the erasing head (see page 17).
Replace all the batteries with new ones if they
are weak.
The tape does not erase
completely.
•
•
Use only better quality tapes.
•
•
•
Do not use a cassette with more than 90 minutes.
Make sure there are no loose layers of tape visible
before inserting the cassette.
Tape jamming or tangling
Clean the heads, pinch roller and capstan
(see page 17).
The sound is weak/The sound
quality is poor.
•
•
The tape has reached its end. Remove it, flip to the
other side and re-insert.
Cassette PLAY button pops up.
IB-CD103(SY)-WM-E-090402
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 12 Watts
DC 9V (6 size “C” batteries)
(Alkaline batteries are recommended)
1
Speakers:
2 - 3 / ” 8 ohm
2
Output power:
Dimensions:
1.5W/channel
1
Width: 14 / ”
Depth: 8”
2
3
Height: 6 / ”
4
Weight: 5LBs (without batteries)
CD Section
Plays disc type:
Any normal CD used in portable players
760 - 800 NM
Laser wavelength:
Tracking method:
Frequency response:
3 - spot error detection
50Hz - 15kHz +1/-2dB
3.86 mm lens
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CDRW encoded discs.
Tape Recorder Section
Frequency response:
Standard normal bias cassette tape,
70Hz - 10kHz
Radio Section
88 - 108 MHz
530 - 1700 kHz
Frequency range:
FM:
AM:
TV1: channels 2-6
TV2(WEATHER BAND): channels 7-13
LENOXX reserves the right to make design and specification changes for
product improvement.
For customer service
Dial 1-800-315-5885
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2002 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
19
IB-CD103(SY)-WM-E-053002
Download from Www.Somanuals.com. All Manuals Search And Download.
|