READ AND UNDERSTAND THESE INSTRUCTIONS
INSTRUCTION SHEET NO.
BEFORE INSTALLING LUMINAIRE.
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at main power supply before proceeding.
IS:1101F
Retain these instructions for maintenance reference.
Page 1 of 3
D1007
INSTALLATION PROCEDURE FOR:
Lytecaster® 1101F, 1001F and 2001F Series Frame-In Kits
CAUTION: (RISK OF FIRE) THIS IS A NON-IC RATED FRAME-IN KIT.
DO NOT INSTALL INSULATION ABOVE OR WITHIN 3 INCHES (76mm) OF ANY PART OF LUMINAIRE.
CAUTION: USE ONLY WITH REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S TRIMS
MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
CAUTION: BEFORE INSTALLING FRAME-IN KIT AND REFLECTOR TRIM, READ ALL MARKINGS ON FRAME-IN KIT AND
REFLECTOR TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.
INSTALLATION INSTRUCTIONS FOR GRID CEILING APPLICATIONS
1
PREPARATION: Cut appropriately sized hole in Ceiling Tile (by
others) at the position desired and place Ceiling Tile in Grid (by
others) (Figure A). Loosen Wing Nuts on Frame Clamps enough to
allow free movement of Mounting Bars (Figure B).
APERTURE HOLE SIZE
1101F SERIES 6-15/16” (176mm) DIA.
1001F SERIES
5-1/4” (134mm) DIA.
2001F SERIES 3-15/16” (100mm) DIA.
2
POSITION LUMINAIRE FRAME: Place Luminaire Frame on top of Ceiling Tile and center the frame aperture on the
Ceiling Tile hole cut in Step 1 so that the aperture wall extends into the Ceiling Tile. Orient the Luminaire Frame to
align with the grid (Figure C). Grasp the T-Bar Clips on each end, one in each hand, lift the clips to the top of the
adjustment slots in the End bracket, extend the End brackets to contact the Ceiling Grid, and drop each T-Bar Clip
over the Grid (Figure D).
NOTE: When the Luminaire Frame is to be used with Wall Wash Trims make sure to orient the Luminaire Frame side
indicated by a label on the frame towards the wall to be illuminated.
3
CLAMP TO GRID and LOCK LUMINAIRE FRAME: Making certain that the Luminaire Frame is still centered on the
Ceiling Tile, tighten the T-Bar Clip Wing Nuts to attach the frame to the Ceiling Grid (Figure E). Retighten the Wing
Nuts on the Frame Lock Clamps after the frame is positioned satisfactorily and is locked to the Ceiling Grid.
Figure A
Figure C
Figure E
Figure B
Figure D
Figure F
BALLAST REPLACEMENT: Ballast replacement must be performed by a “qualified electrician”. TURN OFF
POWER. Remove reflector trim from luminaire. Remove j-box cover to which the ballast is mounted by lifting the
spring. For LC models remove two battery nuts. Remove ballast assembly through the ceiling hole. Disconnect all
input wiring to the ballast. Release all wires from ballast wire connectors by inserting small blade tool, with insulated
handle, into wire release slots (Figure F). Remove ballast from j-box door and replace with new ballast. Rewire and
reassemble.
*
*
REFLECTOR TRIM INSTALLATION: See separate Trim Instruction Sheet for installation procedure.
A
COMPANY
631 Airport Road, Fall River, MA 02720
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTION SHEET NO.
INSTALLATION PROCEDURE FOR:
Lytecaster® 1101F, 1001F and 2001F Series Frame-In Kits
(Continued)
IS:1101F
Page 3 of 3
D1007
INSTALLATION INSTRUCTIONS FOR STEEL CONSTRUCTION APPLICATIONS
1
PREPARATION: Remove Wing Nuts on T-Bar Clips and reverse clips to inside of Luminaire Frame. Loosen Wing
Nuts on Frame Clamps enough to allow free movement of Mounting Bars. Using standard ½” EMT tubing, cut pieces
to required length such that it spans across Hat Channel. Position EMT across Frame Mounting Bars and loosely
secure to End Brackets with T-Bar Clips. (Figures A, B, & C)
NOTE: The Mounting Bars may be readily adjusted to fit desired openings between 13” (330mm) minimum and 24”
(610mm) maximum.
2
POSITION AND INSTALL LUMINAIRE FRAME: Position Luminaire Frame at approximate location with EMT resting
on Hat Channel. Secure EMT to Hat Channel. Adjust frame to final location by sliding along EMT & Mounting Bars.
Lock the Frame in place by tightening the Wing Nuts on the Frame Clamps and T-Bar Clips.
NOTE: When the Luminaire Frame is to be used with Wall Wash Trims make sure to orient the Luminaire
Frame side indicated by a label on the frame towards the wall to be illuminated.
Figure A
Figure B
Figure C
A
COMPANY
631 Airport Road, Fall River, MA 02720
Download from Www.Somanuals.com. All Manuals Search And Download.
|