Life Fitness Treadmill WLE POE S User Manual

95T Treadmills  
Assembly Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TOOLS REQUIRED FOR ASSEMBLY...  
#2 Phillips screwdriver; 4mm, 5mm, 8mm Allen Head Drivers (T-Bar recommended)  
PARTS DESCRIPTION  
1
3
UPRIGHT  
Qty: 1  
2
M12 x 1.75 HEX BUTTON HEAD SCREW  
0017-00101-1984  
Qty: 12  
Qty: 1  
M12.5 WASHER  
0017-00104-0489  
Qty: 12  
4
UPRIGHT  
5
7
HANDRAIL/BRIDGE ASSEMBLY  
Qty: 1  
6
8
CONSOLE BRACKET  
Qty: 1  
M6 x 14 BUTTON HEAD SCREW  
0017-00101-1953  
Qty: 62  
M6.5 WASHER  
0017-00104-0488  
Qty: 11  
9
MASTER WIRE HARNESS  
RIGHT INNER HANDRAIL COVER  
BOTTOM COVER  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 4  
10 TOP COVER  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
11  
13  
15  
17  
12 LEFT INNER HANDRAIL COVER  
14 FRONT NECK SHROUD  
16 DISPLAY CONSOLE  
18 LCD ACCESS COVER  
ACTIVITY ZONE ASSEMBLY  
M5 x 10 PHILLIPS PAN HEAD SCREW  
0017-00101-1995  
19  
21  
REAR CONSOLE COVER  
LEFT REAR ENDCAP  
Qty: 1  
Qty: 1  
20 RIGHT REAR ENDCAP  
Qty: 1  
Qty: 8  
22 #10 x 8 PHILLIPS PAN HEAD SCREW  
0017-00101-1776  
23  
25  
27  
LEFT SIDE EXTRUSION  
RIGHT SIDE EXTRUSION  
RIGHT UPRIGHT COVER  
Qty: 1  
Qty: 1  
Qty: 1  
24 FOAM STRIP  
Qty: 2  
Qty: 1  
Qty: 2  
26 LEFT UPRIGHT COVER  
28 #8 x 12 PHILLIPS PAN HEAD SCREW  
0017-00101-1769  
29  
31  
RUBBER GROMMET  
Qty: 10  
Qty: 3  
30 CUP HOLDER  
Qty: 2  
M6 x 20 SOCKET HEAD SCREW  
0017-00101-1902  
42 CABLE TIE  
Qty: 10  
33  
M6 x 35 BUTTON HEAD SCREW  
0017-00101-1954  
Qty: 2  
2
3
7
8
17  
22  
28  
31  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT!  
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS  
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.  
NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS  
LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION.  
IMPORTANT!  
CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE-  
SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES.  
1.  
2.  
3.  
Remove the six SCREWS (A) securing the MOTOR COVER (B). Lift  
and remove the MOTOR COVER and set it and the SCREWS  
aside.  
G
H
Locate the LEFT UPRIGHT (1). With the notched end facing upward  
and closest to the treadmill, lay the LEFT UPRIGHT near the LEFT  
UPRIGHT MOUNTING BRACKET (C) as shown.  
D
4
E
Feed the CONSOLE CABLE (D) through the front channel (toward  
motor compartment) of the LEFT UPRIGHT (1).  
3
1
Feed the ENTERTAINMENT POWER CABLE (E) through the cen-  
ter channel of the LEFT UPRIGHT (1).  
2
Tilt the LEFT UPRIGHT upward and carefully insert it onto the  
LEFT UPRIGHT MOUNTING BRACKET. Secure the LEFT  
UPRIGHT using three BOLTS (2) and WASHERS (3). Leave the  
BOLTS loose at this time.  
3
2
3
3
2
F
3
B
NOTE: BE CAREFUL NOT TO PINCH THE  
CABLES WHEN INSERTING THE LEFT  
UPRIGHT ONTO THE LEFT UPRIGHT  
MOUNTING BRACKET.  
4.  
5.  
Locate the RIGHT UPRIGHT (4). With the  
E
C
notched end facing upward and closest to the tread-  
mill, lay the RIGHT UPRIGHT near the RIGHT UPRIGHT  
MOUNTING BRACKET (F) as shown.  
A
1
D
Feed the C-SAFE (G) and COAXIAL CABLES (H) through the front  
channel (toward motor compartment) of the RIGHT UPRIGHT (4).  
Tilt the RIGHT UPRIGHT upward and carefully insert it onto the  
RIGHT UPRIGHT MOUNTING BRACKET. Secure the RIGHT  
UPRIGHT using three BOLTS (2) and WASHERS (3). Leave the  
BOLTS loose at this time.  
5
NOTE: BE CAREFUL NOT TO PINCH THE CABLES WHEN  
INSERTING THE RIGHT UPRIGHT ONTO THE RIGHT  
UPRIGHT MOUNTING BRACKET.  
3
2
3
2
2
3
6.  
Carefully insert the HANDRAIL/BRIDGE ASSEMBLY (5) into the  
top of the RIGHT and LEFT UPRIGHTS (1 & 4). Secure the  
HANDRAIL/BRIDGE ASSEMBLY using six BOLTS (2) and WASH-  
ERS (3). Tighten the BOLTS securely.  
4
3
2
1
3
2
NOTE: CAREFULLY PULL BACK THE HANDRAIL SHROUDS TO  
INSTALL THE BOLTS FROM THE FRONT. DO NOT PULL THE  
SHROUDS FURTHER THAN IS NEEDED TO INSTALL THE  
FRONT BOLTS.  
6
8
7
8
7
NOTE: BE CAREFUL NOT TO DAMAGE ANY CABLES WHEN  
INSTALLING THE CONSOLE BRIDGE. LEAVE CABLES LOOSE  
AT THIS TIME.  
7.  
Attach the CONSOLE BRACKET (6) to the HANDRAIL/BRIDGE  
ASSEMBLY (5) as shown using eight SCREWS (7) and WASH-  
ERS (8). Start all eight screws but leave them loose at this time.  
While standing on the treadmill, pull the top of the CONSOLE  
BRACKET toward the user pushing the front edge downward.  
Tighten the four front SCREWS securely. Tighten the remaining  
four back SCREWS securely.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.  
9.  
Secure the ERGO CROSSBAR of the HANDRAIL/BRIDGE  
ASSEMBLY (5) to the CONSOLE BRACKET (6) using three  
SCREWS (31) and three WASHERS (8).  
31  
8
5
NOTE: ROUTE THE HEART RATE CABLES (L) UNDER  
THE MOUNTING TABS AS SHOWN BELOW. BE CARE-  
FUL NOT TO DAMAGE THE HEART RATE CABLES.  
From under the HANDRAIL/BRIDGE ASSEMBLY (5),  
install the MASTER WIRE HARNESS (9) to the CON-  
SOLE (D) and HEART RATE (L) CABLES. WIRE-TIE  
(M) the cables to the CONSOLE BRIDGE as shown.  
Feed the combined connector upward to the back  
of the CONSOLE BRACKET (6).  
Attach the FERRITE (W) to the inside of the  
user left CONSOLE BRACKET POST (X).  
N
Carefully secure the MASTER WIRE  
HARNESS to the CONSOLE BRACKET  
using CABLE TIES (32)  
5
L
L
W
6
X
10. Connect the BASE C-SAFE CABLE (G) to  
the single port end of the C-SAFE SPLIT-  
TER (Z). Connect the C-SAFE EXTENSION  
CABLE (Y) to one of the two ports of the C-  
SAFE SPLITTER (Z).  
5
11. Slide the TOP COVER (10) over the CONSOLE BRACKET (6)  
and onto the CONSOLE BRIDGE (5). Secure it using  
six SCREWS (7). Tighten the SCREWS secure-  
ly.  
10  
M
G
H
Z
Y
9
D
E
NOTE: BE SURE THE TOP COVER  
FULLY SEATS INTO THE ERGO  
CROSSBAR GASKETS.  
12. Install three SCREWS (7) in the three for-  
5
ward-most holes of the OUTER HANDRAIL  
6
COVERS as shown. Tighten the SCREWS  
securely.  
NOTE: ONE SCREW IS LOCATED AT THE  
FRONT OF THE UNIT FOR EACH OUTER  
HANDRAIL COVER.  
7
13. Locate the RIGHT INNER HANDRAIL COVER  
(11). Align it onto the RIGHT HANDRAIL of the  
HANDRAIL/BRIDGE ASSEMBLY (5) as shown  
and secure using five SCREWS (7). Tighten the  
SCREWS securely.  
7
11  
5
7
NOTE: BE SURE TO ENGAGE THE TOP TABS UNDER THE  
PLASTIC RAIL OF THE RIGHT HANDRAIL.  
Repeat for the LEFT INNER HANDRAIL COVER (12).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
14. Locate the BOTTOM COVER (13). Remove the ACCESS  
DOOR (N) and set it aside. Drop the POLAR CABLE (O)  
through the opening. Install the BOTTOM COVER to the  
HANDRAIL/BRIDGE ASSEMBLY (5) using twelve  
SCREWS (7). Connect the POLAR CABLE to the con-  
nector located under the CONSOLE BRIDGE. Tighten the  
SCREWS securely.  
5
10  
NOTE: BE SURE THE BOTTOM COVER FULLY SEATS  
INTO THE ERGO CROSSBAR GASKETS.  
N
NOTE: BE SURE THE BOTTOM COVER IS FULLY  
SEATED TO THE TOP COVER AND ARMS.  
15. Attach the FRONT NECK SHROUD (14) using two  
SCREWS (7). Tighten the SCREWS securely.  
16. Position the ACTIVITY ZONE ASSEMBLY (15) near  
the ERGO CROSSBAR of the HANDRAIL/BRIDGE  
ASSEMBLY (5) as shown. Connect the ACTIVITY  
O
ZONE FLAT RIBBON CABLE (P) and EMERGENCY  
STOP CABLE (Q). Place the ACTIVITY ZONE ASSEM-  
BLY over the TOP and BOTTOM COVERS (10 & 13) and  
secure using two SCREWS (33) through the access door in  
7
13  
7
the BOTTOM COVER. Tighten the SCREWS until the ACTIVI-  
TY ZONE ASSEMBLY is tight against the TOP and BOTTOM  
COVERS. Do not overtighten the SCREWS.  
14  
15  
NOTE: BE SURE TO ROUTE THE FLAT RIBBON CABLE (R)  
Q
OVER THE ERGO CROSSBAR.  
R
NOTE: BE SURE TO ROUTE THE EMERGENCY STOP  
CABLE (R) THROUGH THE NOTCH IN THE BOTTOM  
COVER.  
5
P
17. Replace the BOTTOM COVER ACCESS DOOR (N).  
18. Position the CONSOLE (16) near the CONSOLE  
BRACKET (6). Connect all cables. Secure the  
CONSOLE to the CONSOLE BRACKET using  
four SCREWS (17). Tighten the SCREWS  
securely. Do not overtighten the SCREWS.  
33  
N
NOTE: BE CAREFUL NOT TO DAMAGE THE  
16  
CABLES WHEN INSTALLING THE CON-  
SOLE.  
18  
19. If not already in place, install the LCD  
ACCESS COVER (18) to the REAR CON-  
SOLE COVER (19).  
19  
6
Install the REAR CONSOLE COVER to the  
CONSOLE BRACKET (6) using two  
SCREWS (7). Tighten the SCREWS  
securely. Do not overtighten the  
SCREWS.  
20. Remove the protective backing from the  
four HOOK AND LOOP FASTENERS (S)  
located on the back of the LEFT SIDE  
7
17  
EXTRUSION (23). Align the LEFT SIDE  
EXTRUSION with the channel in the LEFT SIDERAIL  
(T). Tilt and engage the LEFT SIDE EXTRUSION to the  
LEFT SIDERAIL. Press firmly on the underside of the  
LEFT SIDE EXTRUSION to secure the HOOK AND  
LOOP FASTENERS to the frame. (See next page)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. Install the LEFT REAR ENDCAP (21) using two SCREWS (22).Tighten the SCREWS securely. Do not overtighten  
the SCREWS.  
NOTE: BE SURE THE LOCATOR CLIP IS ENGAGED TO THE LEFT SIDE EXTRUSION AS SHOWN IN THE  
DETAIL BELOW.  
22. Install one FOAM STRIP (24) between the LEFT SIDE RAIL and LEFT SIDE EXTRUSION.  
Repeat to install the RIGHT SIDE EXTRUSION (25) to the RIGHT SIDERAIL (U).  
NOTE: BE SURE THE TREADMILL IS IN THE FINAL LOCATION FOR USE BEFORE INSTALLING THE LEFT  
AND RIGHT EXTRUSIONS.  
23. Install the LEFT (26) and RIGHT (27) UPRIGHT COVERS using two SCREWS (22) and one SCREWS (28) each.  
Tighten the SCREWS securely. Do not overtighten the SCREWS.  
Press inward on the UPRIGHT COVER and engage the pre-installed SCREW (V) located at the rear of each  
UPRIGHT COVER.  
24. Reinstall the MOTOR COVER (B) using the six previously removed SCREWS (A). Tighten the SCREWS securely.  
Do not overtighten the SCREWS.  
25. Install the GROMMETS (29) into the screw holes of the INNER HANDRAIL COVERS.  
26. Install the CUP HOLDERS (30).  
NOTE: BE SURE THE TABS ENGAGE FIRST AND TILT INTO PLACE.  
27. The treadmill striding belt must be “walked-in” for five minutes after assembly is complete.  
Plug the treadmill into an appropriate outlet. Turn the treadmill on at the on/off switch. Select QUICK START from  
the console. Increase the speed to 3 mph (4.8 km/h). Start walking in the front left corner of the walking surface  
and drift to the back, move to the center of the deck and walk towards the front, and finally walking to the right  
corner and drifting to the back. Continue pattern for five minutes.  
28. Refer to the Operation Manual for power requirements, proper line cord routing, and other critical product informa-  
tion before connecting the treadmill to a power source. A digital version  
20  
22  
of the Operation Manual can be  
found on the attached  
U
CD.  
21  
22  
4
T
1
27  
V
28  
22  
S
24  
26  
23  
B
A
22  
30  
30  
21  
23  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT!  
CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE-  
SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES.  
Physical Dimensions:  
Length  
Width  
80 inches / 203 centimeters  
37 inches / 94 centimeters  
62.25 inches / 158 centimeters  
Height  
Weight  
95Ti: 450 pounds / 204 kilograms  
95Te: 455 pounds / 206 kilograms  
Step-up Height: 9.5 inches / 24 centimeters  
PRE-OPERATION CHECKLIST (A digital version of the Operation Manual can be found on the attached CD.)  
Ensure that all fasteners are tight.  
Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual.  
Check the operation of the STOP switch and tether switch assembly.  
(See Operation Manual.)  
Confirm the display console is set to English or Metric units.  
(See Optional Settings ENG/MET in Operation Manual.)  
Refer to the Operation Manual for real time clock setting.  
Read the entire Operation Manual before using the treadmill.  
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE  
(Une version électronique du Manuel de l'utilisateur peut être trouvée sur le CD)  
Vérifiez si tous les dispositifs de fixation sont serrés.  
Assurez-vous que le TAPIS est bien tendu et aligné, conformément aux instructions du manuel d'utilisation.  
Vérifiez le fonctionnement de l'interrupteur d'ARRÊT et reliez-le  
(cf. Manuel de l'utilisateur).  
Vérifiez si la console d'affichage est sur le système métrique ou anglais.  
(Référez-vous aux réglages facultatifs relatifs aux systèmes de mesure dans le Manuel de l'utilisateur.)  
Consultez le Manuel de l'utilisateur pour le réglage de l'horloge en temps réel.  
Lisez le Manuel de l'utilisateur dans son intégralité avant d'utiliser le tapis roulant.  
Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the  
Operation Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact the  
nearest Life Fitness Service Center as listed in the OPERATION MANUAL.  
Life Fitness Customer Support Services  
(800) 351-3737 or (847) 451-0036  
Prior to your call, please be sure you have located and noted the  
MODEL NUMBER & SERIAL NUMBER.  
The Model and Serial number are located behind the left end cap of the unit.  
©2008 Life Fitness, a division of Brunswick Corporation. All rights reserved.  
Life Fitness is a trademarks of Brunswick Corporation.  
Polar is a registered trademark of Polar Electro, Inc.  
M051-00K65-C002  
03.08  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kuppersbusch USA Coffeemaker EKV 66000 User Manual
KWC Indoor Furnishings 10031023 User Manual
Leica Projector D120024 User Manual
Lennox Hearth Printer 4650EN User Manual
LG Electronics Personal Computer D4470 User Manual
Lightolier Work Light FBP50 User Manual
Lindy Mouse 20599 User Manual
Linksys Switch WAP11 v26 User Manual
Magic Chef Microwave Oven MCM1110STK User Manual
Mazda Automobile 2005 B2300 Truck User Manual