FIT SERIES FIT-1
ASSEMBLY INSTRUCTIONS
Part # 7317701
Rev B.
1
Revision:8/30/02
Download from Www.Somanuals.com. All Manuals Search And Download.
73
3/8” LOW
HEIGHT LOCK
NUT
60 3/8 X 1” (25m) BOLT
61 3/8 X 1-1/4” (32m) BOLT
75
3/8” SAE
WASHER
52 3/8 X 1-3/4” (43m) BOLT W/NYLOCK
74
62 3/8 X 1-3/4” (43m) BOLT
64 3/8 X 2-1/2” (67m) BOLT
68 3/8 X 2-3/4” (70m) BOLT
3/8” BLACK
SAE WASHER
77 78
RH CAP
(WHITE/PLATINUM/BLACK)
76
RH
WASHER
65 3/8 X 3” (73m) BOLT
63 3/8 X 3-1/2” (90m) BOLT
66 3/8 X 3-3/4” (93m) BOLT
53 3/8 X 4” (97m) BOLT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
67 3/8 X 4-1/4” (106m) BOLT
69 3/8 X 6-1/2” (164m) BOLT
54
1/2”
71 3/8 X 1” (25m) BUTTON HEAD BOLT
FLANGE SPACER
72 3/8 X 3” (76m) BUTTON HEAD BOLT
56
3/4”
FLANGE SPACER
57 1/2 X 3” SHOULDER BOLT
55
1”
FLANGE SPACER
Tools Required forAssembly
* Ratchet with 9/16” socket
* Metric Allen wrench set
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENG TH
1
2
3
4
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
Download from Www.Somanuals.com. All Manuals Search And Download.
5
78
73
75
76
1
3/8 X 3-1/2” (90m) 63
FIGURE 1
STEP 1:
• LOOSELY assemble the REAR UPRIGHT (5) to the BASE (1) to the using four RH CAPS (78), two 3/8 X 3-1/2” BOLTS (63), four
3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 1.
1
2
3
5
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
Download from Www.Somanuals.com. All Manuals Search And Download.
5
3/8 X 3”
(73m) 65
3
4
3/8 X 2-1/2”
(67m) 64
70
78
73
75
76
1
3/8 X 3-1/2”
(90m) 63
FIGURE 2
STEP 2:
• LOOSELY assemble the LEFT and RIGHT BOOM SUPPORTS (3 & 4) to the BASE (1) using eight RH CAPS (78), four 3/8 X 3-
1/2” BOLTS (63), eight 3/8” SAE WASHERS (75), eight 3/8” RH WASHERS (76) and four 3/8” LOW HEIGHT LOCK NUTS (73)
as shown in FIGURE 2.
• LOOSELY assemble the LEFT and RIGHT BOOM SUPPORTS (3 & 4) to the REAR UPRIGHT (5) using four RH CAPS (78), two
3/8 X 3” BOLTS (65), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS
(73) as shown in FIGURE 2.
• LOOSELY assemble the CROSS SUPPORT (70) between the LEFT and RIGHT BOOM SUPPORTS (3 & 4) using eight RH CAPS
(78), four 3/8 X 2-1/2” BOLTS (64), eight 3/8” SAE WASHERS (75), eight 3/8” RH WASHERS (76) and four 3/8” LOW HEIGHT
LOCK NUTS (73) as shown in FIGURE 2.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
78
75
76
3
25
60 3/8 X 1” (25m)
FIGURE 3
STEP 3:
• SECURELY assemble one STORAGE PEG (25) to the LEFT BOOM SUPPORT (3) using one RH CAPS (78), one 3/8 X 1” BOLT
(60), one 3/8” SAE WASHER (75) and one 3/8” RH WASHER (76) as shown in FIGURE 3.
76
75
63 3/8 X 3-1/2” (90m)
78
73
5
6
1
3/8 X 4” (97m) 53
FIGURE 4
STEP 4:
• LOOSELY assemble the UPRIGHT SUPPORT (6) to the BASE (1) and REAR UPRIGHT (5) using eight RH CAPS (78), two 3/8 X
3-1/2” BOLTS (63), two 3/8 X 4” BOLTS (53), eight 3/8” SAE WASHERS (75), eight 3/8” RH WASHERS (76) and four 3/8” LOW
HEIGHT LOCK NUTS (73) as shown in FIGURE 4.
1
2
3
7
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
Download from Www.Somanuals.com. All Manuals Search And Download.
12
2
SPRING PIN
FIGURE 5
STEP 5:
• Pull back on the SPRING PIN and slide the ADJUSTABLE SEAT (12) over the BENCH FRAME (2) as shown in FIGURE 5.
6
73
76
75
53 3/8 X 4” (97m)
78
1
2
3/8 X 3-1/2” (90m) 63
FIGURE 6
STEP 6:
• LOOSELY assemble the BENCH FRAME (2) to the UPRIGHT SUPPORT (6) and the BASE (1) using eight RH CAPS (78), two
3/8 X 3-1/2” BOLTS (63), two 3/8 X 4” BOLTS (53), eight 3/8” SAE WASHERS (75), eight 3/8” RH WASHERS (76) and four
3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 6.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGHTEN!
TIGHTEN!
FIGURE 7
STEP 7:
• Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS
(78) over the RH WASHERS (76) on all tightened connections.
1
2
3
9
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
Download from Www.Somanuals.com. All Manuals Search And Download.
73
75
76
7
3/8 X 4-1/4” (106m) 67
47
78
2
FIGURE 8
STEP 8:
• Insert one 3-5/16” PIVOT SHAFT (47) into the PEDESTAL (7) as shown in FIGURE 8.
• SECURELY assemble the PEDESTAL (7) to the BENCH FRAME (2) using two RH CAPS (78), one 3/8 X 4-1/4” BOLT (67), two
3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as shown in FIGURE 8.
18
7
39
32
59
51
FIGURE 9
STEP 9:
• Assemble four 5 X 8” ROLLER PADS (39) and eight 2-3/8” OD PLASTIC WASHERS (32) to the PEDESTAL (7) using four 1-
1/4” SHAFT COLLARS (51) and two 19-1/4” ROLLER PAD TUBES (18) as shown in FIGURE 9.
• Once the 5 X 8” ROLLER PADS (39) are assembled to the PEDESTAL (7), SECURE the 19-1/4” ROLLER PAD TUBES (18)
with the four 5/16 X 1/4” SET SCREWS as shown in FIGURE 9.
• Insert two 3 X 2” END CAPS (59) into the ends of the PEDESTAL (7) as shown in FIGURE 9.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
12
73
3/8 X 4-1/4”
(106m) 67
76
75
BLACK 77
FIGURE 10
STEP 10:
• SECURELY assemble the SEAT SUPPORT (11) to the ADJUSTABLE SEAT (12) using two BLACK RH CAPS (77), one 3/8 X 4-
1/4” BOLTS (67), two 3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as
shown in FIGURE 10.
15
6
46
FIGURE 11
STEP 11:
• Insert two 5-1/2” PIVOT SHAFTS (46) into the UPRIGHT SUPPORT (6) and BACK PAD SUPPORT (15) as shown in FIGURE 11..
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
11
Download from Www.Somanuals.com. All Manuals Search And Download.
15
73
6
12
17
76
75
67 3/8 X 4-1/4” (106m)
BLACK 77
69 3/8 X 6-1/2” (164m)
FIGURE 12
STEP 12:
• SECURELY assemble the BACK PAD SUPPORT (15) to the ADJUSTABLE SEAT (12) using two BLACK RH CAPS (77), one
3/8 X 4-1/4” BOLT (67), two 3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT
(73) as shown in FIGURE 12.
• SECURELY assemble the BACK PAD SUPPORT (15) to the UPRIGHT SUPPORT (6) using two BACK PAD ADJUST PLATES
(17), four BLACK RH CAPS (77), two 3/8 X 6-1/2” BOLTS (69), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS
(76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 12.
42
11
76
75
3/8 X 1-1/4” (32m) 61
77 BLACK
FIGURE 13
STEP 13:
• SECURELY assemble the SEAT PAD (42) to the SEAT SUPPORT (11) using three BLACK RH CAPS (77), three 3/8 X 1-1/4”
BOLTS (61), three 3/8” SAE WASHERS (75) and three 3/8” RH WASHERS (76) as shown in FIGURE 13.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43
15
76
75
3/8 X 3” (73m) 65
BLACK 77
FIGURE 14
STEP 14:
• SECURELY assemble the BACK PAD (43) to the BACK PAD SUPPORT (15) using two BLACK RH CAPS (77), two 3/8 X 3”
BOLTS (65), two 3/8” SAE WASHERS (75) and two 3/8” RH WASHERS (76) as shown in FIGURE 14.
FIGURE 15
51
32
19
39
6
STEP 15:
• Assemble two 5 x 8” ROLLER PADS (39) and four 2-3/8” OD PLASTIC WASHERS (32) to the UPRIGHT SUPPORT (6) using
two 1-1/4” SHAFT COLLARS (51) and one 21-1/2” ROLLER PAD TUBE (19) as shown in FIGURE 15.
• Once the 5 X 8” ROLLER PADS (39) are assembled to the UPRIGHT SUPPORT (6), SECURE the 21-1/2” ROLLER PAD
TUBE (19) with the two 5/16 x 1/4” SET SCREWS.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
13
Download from Www.Somanuals.com. All Manuals Search And Download.
13
73
1
78
76
75
53 3/8 X 4” (97m)
FIGURE 16
STEP 16:
• SECURELY assemble the SWIVEL SUPPORT (13) to the BASE (1) using four RH CAPS (78), two 3/8 X 4” BOLTS (53), four 3/
8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 16.
1/2 X 3” 57
13
76
75
73
14
78
FIGURE 17
STEP 17:
• SECURELY assemble the SWIVEL (14) to the SWIVEL SUPPORT (13) using one 1/2 X 3” SHOULDER BOLT (57), one 3/8” SAE
WASHER (75), one 3/8” RH WASHER (76), one 3/8” LOW HEIGHT LOCK NUT (73) and one RH CAP (78) as shown in FIGURE
17.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 18:
36
• Slide two 5” ACCORIDIAN SLEEVES
(36) over the shafts on the PIVOT ARM
(9) as shown in FIGURE 18.
37
• Slide two PILLOW BLOCKS (37) over
the shafts on the PIVOT ARM (9) as
shown in FIGURE 18.
9
FIGURE18
4
3/8 X 3” (76m) 72
BUTTON HEAD
74
35
37
3
9
78
75
73
76
FIGURE 19
STEP 19:
• SECURELY assemble the PILLOW BLOCKS (37) on the PIVOT ARM (9) to the LEFT and RIGHT BOOM SUPPORTS (3 & 4)
using four 3/8 X 3” BUTTON HEAD BOLTS (72), four BLACK 3/8” SAE WASHERS (74), four RH WASHERS (76), four 3/8”
SAE WASHERS (75), four 3/8” LOW HEIGHT LOCK NUTS (73) and four RH CAPS (78) as shown in FIGURE 19.
• IMPORTANT! When PIVOT ARM (9) is centered and level in the PILLOW BLOCKS (37), tighten the PILLOW BLOCK set
screws.
• Slide two 1-3/8” OD COVER CAPS (35) over the ends of the shaft on the PIVOT ARM (9) as shown in FIGURE 19.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 20
77 BLACK
26
78
9
41
73
75
76
3/8 X 2-1/2”
(67m) 64
63 3/8 X 3-1/2” (90m)
BLACK
77
78
STEP 20:
• SECURELY assemble the PRESS ADJUST PLATE (26) to the PIVOT ARM (9) using three BLACK RH CAPS (77),three RH
CAPS (78), two 3/8 X 2-1/2” BOLTS (64), one 3/8 X 3-1/2” BOLT (63), six 3/8” SAE WASHERS (75), six 3/8” RH WASHERS
(76) and three 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 20.
• Insert one 5-1/2” TAPPED PIVOT SHAFT (41) into the PIVOT ARM (9).
BLACK 77
73
60 3/8 X 1” (25m)
16
78
9
76
10
75
3/8 X 1-3/4”
(43m) W/NYLOCK 52
78
FIGURE 21
STEP 21:
• SECURELY assemble the PRESS ARM (10) to the PIVOT ARM (9) using two RH CAPS (78), two 3/8 X 1-3/4” BOLTS W/
NYLOCK (52), two 3/8” SAE WASHERS (75) and two 3/8” RH WASHERS (76) as shown in FIGURE 21.
• SECURELY assemble the COUNTERBALANCE (16) to the PIVOT ARM (9) using two RH CAPS (78),two BLACK RH CAPS
(77), two 3/8 X 1” BOLTS (60), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT LOCK
NUTS (73) as shown in FIGURE 21.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
50
FIGURE 24
27
29
31
58
30
20
1
STEP 24:
•
Insert two GUIDE RODS (27) through the BOTTOM SHROUD BRACKET (20) and into the BASE (1) as shown on FIGURE 24.
•
(NOTE: Lubricate GUIDE RODS (27) with silicon or teflon spray available at most hardware stores.)
•
Slide two 3/4 X 2” WEIGHT STACK CUSHIONS (30) down over the GUIDE RODS (27) as shown in FIGURE 24.
• Using EXTREME CARE slide all twenty WEIGHT PLATES (31) down over the GUIDE RODS (27) on to the 3/4 X 2” WEIGHT
STACK CUSHIONS (30). Make sure that the WEIGHT PLATES (31) are all facing as shown.
• Slide the HEAD PLATE ASSY (29) down over the GUIDE RODS (27) onto the weight stack.
•
Slide two 13/16” SHAFT COLLARS (50) over the GUIDE RODS (27) as shown in FIGURE 7.
• Apply WEIGHT STACK LABELS (58) to WEIGHT PLATES (31) and HEAD PLATE (29) as shown in FIGURE 24. Begin with first
number on at the HEAD PLATE (29) with larger numbers in consecutive order towards bottom of weight stack.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8
27
FIGURE 25
STEP 25:
• CAREFULLY assemble the STACK BOOM (8) over the GUIDE RODS (27) as shown in FIGURE 25.
73
75
76
3/8 X 2-1/2” (67m) 64
5
8
78
FIGURE 26
STEP 26:
•
LOOSELY assemble the STACK BOOM (8) to the REAR UPRIGHT (5) using two RH CAPS (78), one 3/8 X 2-1/2” BOLT
(64), two 3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as shown in
FIGURE 26.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
18
Download from Www.Somanuals.com. All Manuals Search And Download.
5
78
73
3/8 X 3/4” 56
8
75
76
44
54
50
TIGHTEN!
38
64 3/8 X 2-1/2” (67m)
65 3/8 X 3” (73m)
FIGURE 27
STEP 27:
• Route the LAT CABLE (44) through the REAR UPRIGHT (5). Then assemble two 4-1/2” PULLEYS (38) and asssemble the
PULLEYS to the REAR UPRIGHT (5) using four RH CAPS (78), one 3/8 X 2-1/2” BOLT (64), one 3/8 X 3” BOLT (65), four
3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76), three 3/8 X 1/2” FLANGE SPACERS (54), one 3/8 X 3/4” FLANGE
SPACER (56) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 27. (NOTE: Make sure CABLE is in
groove of PULLEY before tightening BOLTS.)
• SECURELY tighten STACK BOOM (8) to the REAR UPRIGHT (5) as shown in FIGURE 27.
• Slide the two 13/16” SHAFT COLLARS (50) to the top of the STACK BOOM (8) and SECURELY tighten the SHAFT COLLAR
(50) set screws.
73
75
76
8
38
62 3/8 X 1-3/4” (43m)
44
78
21
FIGURE 28
STEP 28:
• Route the LAT CABLE (44) around one 4-1/2” PULLEY (38) and up thru the STACK BOOM (8).Assemble the PULLEY to two
DUAL PULLEY PLATES (21) using two RH CAPS (78), one 3/8 X 1-3/4” BOLT (62), two 3/8” SAE WASHERS (75), two 3/8”
RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as shown in FIGURE 28.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
77 BLACK
73
38
75
76
54
8
49
68 3/8 X 2-3/4” (70m)
78
44
33
29
FIGURE 29
STEP 29:
• SECURELY assemble two 4-1/2” PULLEYS (38) to the BOOM (8) using two BLACK RH CAPS (77), two RH CAPS (78), two
3/8 X 2-3/4” BOLTS (68), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76), four 3/8 X 1/2” FLANGE SPACERS
(54), two 2-7/8 X 2-1/4” CABLE CLIPS (49) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 29.
• Slide one WEIGHT STACK PIN (33) over the STEM on the HEAD PLATE (29) as shown in FIGURE 29.
• Screw the threaded end of the LAT CABLE (44) all the way onto the end of the STEM on the HEAD PLATE (29) and tighten jam
nut securely. See FIGURE 29.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
20
Download from Www.Somanuals.com. All Manuals Search And Download.
78
22
62 3/8 X 1-3/4” (43m)
3/8 X 1-3/4”
(43m) 62
9
38
78
76
75
77
BLACK
14
45
73
FIGURE 30
STEP 30:
• Route the LEG CABLE (45) through the SWIVEL (14) and assemble two 4-1/2” PULLEYS (38) to the SWIVEL (14) using four
BLACK RH CAPS (77), two 3/8 X 1-3/4” BOLTS (62), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two
3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 30.
• Route the LEG CABLE (45) around one 4-1/2” PULLEY (38) and assemble the PULLEY (38) and the PULLEY GUARD (22)to
the PIVOT ARM (9) using two RH CAPS (78), one 3/8 X 1-3/4” BOLT (62), two 3/8” SAE WASHERS (75), two 3/8” RH
WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as shown in FIGURE 30.
38
1
73
45
62
3/8
76
X 1-3/4”
(43 m)
78
75
FIGURE 31
STEP 31:
• Route the LEG CABLE (45) around a 4-1/2” PULLEY (38) and assemble it to the bracket on the BASE (1) using four RH CAPS
(78), two 3/8 X 1-3/4” BOLTS (62), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT
LOCK NUTS (73) as shown in FIGURE 31.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
73
75
76
21
62 3/8 X 1-3/4” (43m)
78
38
38
73
76
78
75
3/8 X 1-3/4”
(43m)
62
45
1
FIGURE 32
STEP 32:
• Route the LEG CABLE (45) around one 4-1/2” PULLEY (38) and assemble the PULLEY (38) to the lower holes of the two
DUAL PULLEY PLATES (21) using two RH CAPS (78), one 3/8 X 1-3/4” BOLT (62), two 3/8” SAE WASHERS (75), two 3/8”
RH WASHERS (76) and one 3/8” LOW HEIGHT LOCK NUT (73) as shown in FIGURE 32.
• Route the LEG CABLE (45) around a 4-1/2” PULLEY (38) and assemble it to the bracket on the BASE (1) using four RH CAPS
(78), two 3/8 X 1-3/4” BOLTS (62), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76) and two 3/8” LOW HEIGHT
LOCK NUTS (73) as shown in FIGURE 32.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
22
Download from Www.Somanuals.com. All Manuals Search And Download.
73
38
7
BLACK
77
73
38
45
49
1
76
75
78
62 3/8 X 1-3/4” (43m)
55
76
75
3/8 X 3-3/4” (93m) 66
62 3/8 X 1-3/4” (43m)
2
78
FIGURE 33
STEP 33:
• Route the LEG CABLE (45) through the bracket on the BASE (1) and assemble one 4-1/2” PULLEY (38) to the bracket on the
BASE (1) using four RH CAPS (78), two 3/8 X 1-3/4” BOLTS (62), four 3/8” SAE WASHERS (75), four 3/8” RH WASHERS (76)
and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 33.
• Route the LEG CABLE (45) through the BENCH FRAME (2) and assemble one 4-1/2” PULLEY (38) to the BENCH RAME (2)
using one RH CAP (78), one BLACK RH CAP (77), one 3/8 X 3-3/4” BOLT (66), two 3/8 X 1”FLANGE SPACERS (55), two
3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76), one CABLE CLIP (49) and one 3/8” LOW HEIGHT LOCK NUT (73)
as shown in FIGURE 33.
• Assemble the swivel end of LEG CABLE (45) to the PEDESTAL (7) using two RH CAPS (78), one 3/8 X 1-3/4” BOLT (62), two
3/8” SAE WASHERS (75), two 3/8” RH WASHERS (76), and one 3/8” LOW HEIGHT LOCK NUT (73). See FIGURE 33.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
28
40
44
45
40
48
34
FIGURE 34
STEP 34:
•
Assemble the LOW ROW BAR (34) to the LEG CABLE (45) using two SNAP LINKS (40) and one 12-LINK CHAIN (48) as
shown in FIGURE 34.
•
Assemble the LAT BAR (28) to the LAT CABLE(44) using one SNAP LINK (40) as shown in FIGURE 34.
1
2
3
4
5
6
1/2
1/2
40
1/2
1/2
90
1/2
1/2
140
0
10
20
30
50
60
70
80
100
110
120
130
150
24
Download from Www.Somanuals.com. All Manuals Search And Download.
8
74
71 3/8 X 1” (25m)
BUTTON HEAD
24
23
20
SERIAL #
LOCATION
FIGURE 35
STEP 35:
• SECURELY assemble the LEFT and RIGHT SHROUDS (23 & 24) to the STACK BOOM (8) and BOTTOM SHROUD
BRACKET (20) using eight 3/8 X 1” BUTTON HEAD BOLTS (71) and eight 3/8” BLACK SAE WASHERS (74) as shown in
FIGURE 35.
•
Adjustments can be made in the above locations to set the correct amount of tension in the cables.
•
If upon completion of assembly, the HEAD PLATE (29) does not sit on top of the first WEIGHT PLATE (31), push the HEAD
PLATE (29) down, insert the WEIGHT STACK PIN (33) and perform several repetitions. This will relax the cable system and
prevent the HEAD PLATE (29) from lifting up. See FIGURE 35.
•
For maximum performance, the HEAD PLATE (29) should just barely sit on the top WEIGHT PLATE (31).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10YEARS
1 YEAR
STRUCTURUAL FRAME
PILLOW BLOCKS, PULLEYS, WEIGHT PLATESAND GUIDE RODS
1 YEAR
CABLES
90 DAYS
UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action
DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery
Guide Rods
Hand Grips
X
X
X
INSPECT
Visual Overall
Cables
Hardware
Frame
X
X
X
X
X
Hand Grips
LUBRICATE
Guide Rods
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800) 351-3737
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES FIT-1. If unsure of proper use of equipment, call
your local LifeFitness distributor or call the LifeFitness customer service department at
(800) 351-3737.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|