CLUB SERIES LAT PULLDOWN
ASSEMBLY INSTRUCTIONS
Part # 6941801
1
Revision:08/02/00
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1B
11
10 3/8 X 3-3/4”
14
3
27
FIGURE 1
STEP 1:
• LOOSELY assemble the TOWER (1) to the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/4” BOLTS (10),
four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 1.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2E
2D
2L
1A
2M
2K
2A
2N
2G
2J
2C
2F
2H
2I
2B
1A
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1A
1B
2
11
14
13
9 3/8 X 2-3/4
27
3
3/8 X 3-3/4” 10
FIGURE 2
STEP 2:
• LOOSELY assemble the MAIN UPRIGHT (2) to the base of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/
4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 2.
• LOOSELY assemble the MAIN UPRIGHT (2) to the top tube of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X
2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS
(11) as shown in FIGURE 2.
• Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS
(27) over the RH WASHERS (14) on all tightened connections.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 3
1A
17
9 3/8 X 2-3/4”
13
14
5B
8A
5C
5
5A
5D
3
11
27
STEP 3:
• SECURELY assemble the KNEE SUPPORT (5) to the BENCH FRAME (3) using two BLACK RH CAPS (17), two RH CAPS
(27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT
LOCK NUTS (11) as shown in FIGURE 3.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
6
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5A
18
3
14
3/8 X 2-3/4” 9
27
FIGURE 4
STEP 4
• SECURELY assemble the SEAT PAD (18) to the BENCH FRAME (3) using two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9) and
two 3/8” RH WASHERS (14) as shown in FIGURE 4.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5
6
20
19
15
1
8
26
24
1A
24
25
16
HEAVYWEIGHT
OPTION
STEP 5:
• Insert the two GUIDE RODS (26) (found in the SHROUD KIT) into the base of the TOWER (1) as shown in FIGURE 5. Lubricate
the GUIDE RODS (26) with a slicon or teflon spray that is available at most hardware stores.
• Slide two WEIGHT STACK CUSHIONS (16) down over the GUIDE RODS (26). See FIGURE 5.
• Using EXTREME CARE place twenty 10 LB. WEIGHT PLATES (24) over the GUIDE RODS (26) as shown in FIGURE 5.
(NOTE: If HEAVY WEIGHT OPTION is being used, slide ten 15LB. WEIGHT PLATES (25) over the GUIDE RODS (26)
first, then slide ten 10 LB. WEIGHT PLATES (24) over the GUIDE RODS.)
• Carefully Slide the HEAD PLATE (8) down over the GUIDE RODS (26) onto the weight stack as shown in FIGURE 5.
• Slide one WEIGHT STACK SELECTOR PIN (15) over the shaft on the HEAD PLATE (8) as shown in FIGURE 5.
• Slide two 1” SHAFT COLLARS (19) over each GUIDE ROD (26) as shown in FIGURE 5.
• Slide two GUIDE ROD BUSHINGS (20) over each GUIDE ROD (26).
• Place the GUIDE ROD SUPPORT (6) over the GUIDE RODS (26) as shown in FIGURE 5.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
8
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
11
FIGURE 6
1
14
9 3/8 X 2-3/4”
27
2
6
20
19
TIGHTEN!
26
1A
8
24
15
STEP 6:
• SECURELY assemble the GUIDE ROD SUPPORT (6) to the TOWER (1) and MAIN UPRIGHT (2) using four RH CAPS (27), two
3/8 X 2-3/4” BOLTS (9), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 6.
• Slide GUIDE ROD BUSHINGS (20) into the tubes on the GUIDE ROD SUPPORT (6), slide 1” SHAFT COLLARS (19) under-
neath the GUIDE ROD BUSHINGS (20) and SECURELY tighten the set screws.
• Insert the WEIGHT STACK PIN (15) into the WEIGHT STACK as shown in FIGURE 6.
• Screw the treaded end of the CABLE all way into the end of the shaft on the HEAD PLATE (8) and tighten jam nut securely. See
FIGURE 6.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGHTEN!
FIGURE 7
8
24
12
ST`````
• The WEIGHT STACK LABEL sheet (12) includes labels for both lbs. and kgs. for both the standard and optional weight stacks.
• Peel the backing off the WEIGHT STACK LABELS (12), line up sheet to the right of the selector opening and apply labels to
the WEIGHT PLATES (24), starting with the HEAD PLATE (8) as shown in FIGURE 7.
• REFER TO SHROUD KITASSEMBLY INSTRUCTIONS.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
32
22 23
31
4
21
29
7
4A
FIGURE 8
STEP 8:
• Assemble the PLACARD LABEL (22) or the FOREIGN LANGUAGE PLACARD LABEL (23) to the FRONT SHROUD as shown
in FIGURE 8.
• Attach LAT BAR (4) and/or TRICEP ROPE (7) end of cable using on SNAP LINK (21) with the TRICEP ROPE (7) as shown in
FIGURE 8.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
27S
30
29
1
28 3/8 X 3-1/2”
FIGURE 8
STEP 8:
(NOTE: If the PARTIAL SHROUD KIT is being used follow STEP 8. If the FULL SHROUD KIT is being used follow STEP 9.)
• SECURELY assemble the FRONT PARTIAL SHROUD (29) and the REAR PARTIAL SHROUD (30) to the TOWER (1) using
twelve 3/8 X 3-1/2” BUTTON HEAD BOLTS (28), twelve STARLOCK WASHERS (27), and twelve 3/8” ACORN NUTS (12)
as shown in FIGURE 8.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
27
12
32
1
31
3/8 X 3-1/2” 28
FIGURE 9
STEP 9:
• SECURELY assemble the FRONT FULL SHROUD (31) and the REAR FULL SHROUD (32) to the TOWER (1) using ten 3/8 X
3-1/2” BUTTON HEAD BOLTS (28), ten STARLOCK WASHERS (27), and ten 3/8” ACORN NUTS (12) as shown in FIGURE
9.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10YEARS
3 YEARS
1 YEAR
STRUCTURUAL FRAME
PILLOW BLOCKS, PULLEYS, WEIGHT PLATESAND GUIDE RODS
CABLES
90 DAYS
UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action
DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery
Guide Rods
Hand Grips
X
X
X
INSPECT
Visual Overall
Cables
Hardware
Frame
X
X
X
X
X
Hand Grips
LUBRICATE
Guide Rods
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800)328-9714.
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES LAT PULLDOWN. If unsure of proper use of
equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at
(800) 328-9714.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|