844 LAT OPTION
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H
PART # 7079701
REV. B
1
Version: 844107
Revision: 06/19/01
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 844 Lat Option. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Tools Required forAssembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
UPRIGHT
QTY
1
KEY PART #
DESCRIPTION
3/8 X 3-1/4” BOLT
3/8” WASHER
QTY
2
1
2
3
4
5
6
7
8
9
6608708
6608508
6274402
6275302
6609002
6610402
6546302
6609308
3116101
19
20
21
22
3102915
3102501
3102802
6480301
TOP BOOM
1
10
11
8
LOW ROW BAR
LAT BAR
1
3/8” LOCK NUT
1
3/8” FLANGE SPACER
1/2 X 2-3/4” BOLT
1/2 X 3” BOLT
LOW ROWATTACHMENT
KNEESUPPORT
CARRIAGE
1
23 3102953
24 3102910
25 3102502
26 3102801
27 6692601
28 3119301
29 6236701
30 3116001
31 6140701
32 6177001
33 3103801
1
1
3
1
1/2” WASHER
4
LOWPULLEYHOUSING
4-1/2”PULLEY
3-1/2”PULLEY
LATCABLE
1
1/2” LOCK NUT
2
1
3 X 2” END CAP
1
10 3116201
11 6610501
12 6576201
13 6176201
14 6542402
15 3103102
16 3102933
17 3102922
18 3102904
5
2-1/2” ROUND END CAP
1-3/4” SQ. END CAP
1-1/4” SQ. RUBBER BUMPER
1 X 1” GLIDE
2
1
1
LOW ROW CABLE
ROLLERPAD
1
1
2
8
1-3/4” X 5-1/4” PLATE
1 X 8” GRIP
2
NON-SKID STRIP
5/16” SNAP LINK
2
4
3
3/8 X 2” BOLT
2
34 3108102 1/4” QUICK DISCONNECT LINK
35 6075906 12 LINK CHAIN
1
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
5
1
2
5
28
32
FIGURE 1
STEP 1:
• Insert two 2-1/2” ROUND END CAPS (28) to the LOW ROWATTACHMENT (5) as shown in FIGURE 1.
• Attach two NON-SKID STRIPS (32) to the LOW ROWATTACHMENT (5) as shown in FIGURE 1.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER RACK
1
1/2 X 3” 24
25
26
8
21
20
20
3/8 X 3-1/4” 19
5
FIGURE 2
STEP 2:
• Assemble the LOW ROW ATTACHMENT (5) and the LOW PULLEY HOUSING (8) to the POWER RACK using two
3/8 X 3-1/4” BOLTS (19), four 3/8” WASHERS (20), and two 3/8” LOCK NUTS (21). See FIGURE 2.
• SECURELY assemble the UPRIGHT (1) to the LOW PULLEY HOUSING (8) using two 1/2 X 3” BOLTS (24), two 1/2” WASH-
ERS (25), and one 1/2” LOCK NUTS (26). See FIGURE 2.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
31
7
31
30
FIGURE 3
STEP 3:
• Apply eight 1” SQ. GLIDES (31) to the inside of the CARRIAGE (7) as shown in FIGURE 3.
• Attach one 1-1/4” SQ. RUBBER BUMPER (30) to the bottom of the CARRIAGE (7) as shown in FIGURE 3.
7
1
FIGURE 4
STEP 4:
• CAREFULLY slide the CARRIAGE (7) over the UPRIGHT (1) as shown in FIGURE 4.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAM
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
17 3/8 X 2-3/4
2
22
22
27
11
21
10
FIGURE 5
STEP 5:
•
Insert one 2 X 3” END CAP (27) into the TOP BOOM (2) as shown in FIGURE 5.
•
•
Route threaded end of the LAT CABLE (11) through the TOP BOOM (2) as shown in FIGURE 5.
SECURELY assemble three 3-1/2” PULLEYS (10) to the TOP BOOM (2) using three 3/8 X 2-3/4” BOLTS (17), six 3/8”
FLANGE SPACERS (22), and three 3/8” LOCK NUTS (21). See FIGURE 5. (NOTE: BEFORE TIGHTENING, MAKE SURE
CABLE (11) IS IN THE GROOVES OF THE PULLEYS.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 6
23
POWER RACK
21
2
26
25
24
1
20
18
STEP 6:
• SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1) using one 1/2 X 2-3/4” BOLT (23), one 1/2 X 3” BOLT (24), two
1/2” WASHERS (25), and one 1/2” LOCK NUT (26). See FIGURE 6.
• SECURELY assemble the TOP BOOM (2) to the top of the POWER RACK using two 3/8 X 3” BOLTS (18), four 3/8” WASH-
ERS (20), and two 3/8” LOCK NUTS (21). See FIGURE 6.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 7
STEP 7:
• Loop the LAT CABLE (11) around one 3-1/2” PULLEY (10) as shown in FIGURE 7.
•
LOOSELY assemble the 3-1/2” PULLEY (11) to the1-3/4 X 5-1/4” PLATES (14) using one 3/8 X 2” BOLT (16) and one 3/8”
LOCK NUT (21). See FIGURE 7.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 8
34
7
!IMPORTANT!
SECURELY
TIGHTEN
STEP 8:
• Attach the LAT CABLE (11) to the CARRIAGE (7) using one 1/4” QUICK LINK (34) as shown in FIGURE 8. (IMPORTANT!
Securely tighten QUICK LINK.)
3/8 X 2-3/4” 17
9
23
21
8
20
FIGURE 9
STEP 9:
• Loop the ball end of the LOW ROW CABLE (12) around one 4-1/2” PULLEY (9) and SECURELY assemble the 4-1/2” PULLEY
(9) to the LOW PULLEY HOUSING (8) using two 3/8 X 2-3/4” BOLTS (17), two 3/8” FLANGE SPACERS (22), two 3/8” WASH-
ERS (20), and two 3/8” LOCKNUTS (21). (NOTE: Make sure CABLE is routed between the PULLEY and the retaining bolt
as shown in FIGURE 9.)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 10
14
10
21
12
16 3/8 X 2”
STEP 10:
•
Loop the LOW ROW CABLE (12) around one 3-1/2” PULLEY (10) as shown in FIGURE 10.
•
LOOSELY assemble the 3-1/2” PULLEY (10) to the 1-3/4 X 5-1/4” PLATES (14) using one 3/8 X 2” BOLT (16) and one 3/8”
LOCK NUT (21). See FIGURE 10.
•
SECURELY tighten the two 3/8 X 2” BOLTS (16) of the 1-3/4 X 5-1/4” PLATES (14).
12
8
FIGURE 11
STEP 11:
•
SECURELY thread the end of the LOW ROW CABLE (12) 3/4 of the way into into the threaded housing on the LOW PULLEY
HOUSING (8) and SECURELY tighten jam nut.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12:
15
FIGURE 12
•
Attach the LAT BAR (4) to the ball end of
the LATCABLE (11) using one SNAP LINK
(33) as shown in FIGURE 12..
33
•
Slide two 1 X 8” GRIPS (15) over the ends
of the LAT BAR (4) as shown in FIGURE
12.
11
4
STEP 13:
• Attach the LOW ROW BAR (3) to the ball end
of the LOW ROW CABLE (12) using two
SNAP LINKS (33) and one 12 LINK CHAIN
(35) as shown in FIGURE 13.
12
•
Slide two 1 X 8” GRIPS (15) over the ends of the
LOW ROW BAR (3) as shown in FIGURE 13.
35
33
3
18
FIGURE 13
STEP 14:
•
Slide two ROLLER PADS (13) onto the KNEE
SUPPORT (6), then insert one 1-3/4” SQ. END
6
CAP (29) into the end of the KNEE SUPPORT (6)
as shown in FIGURE 14.
13
FIGURE 14
29
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 15
6
SAFETY
RAIL
STEP 15:
• When performing the LAT PULL exercise, insert the KNEE SUPPORT (6) into the hole of the SAFETY RAIL as shown in
FIGURE 15 and simply lower the SAFETY RAIL down until roller pads contact knees.
THIS CONCLUDES THE ASSEMBLY OF THE 844 LAT OPTION
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
Thank you for purchasing the ParaBody 844 Lat Option.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONSAND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: 763.323.4500 Fax: 763.323.4797
800.328.9714 (Toll-free within the U.S. and Canada)
INTERNATIONALOFFICES
Life FitnessAtlantic BV
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
Life Fitness Benelux N.V.
Bijdorpplein 25-31
85716 Unterschleissheim
Germany
2992 LB Barendrecht
The Netherlands
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Italia S.R.L.
Via Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
Download from Www.Somanuals.com.1A7ll Manuals Search And Download.
|