®
COMPACT DISC PLAYER
AM/FM STEREO CASSETTE RECORDER
MODEL CD-108
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
RECEIVES AM/FM STEREO BROADCASTS
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
FM STEREO AND POWER INDICATORS
2 WAY POWER - AC/DC
BASS BOOST SWITCH
REQUIRES 8 SIZE “C” BATTERIES
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualified service
personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be
sure the antenna system is grounded so as to provide some protection against voltage
surges and built up static charges. Section 810 of the National Electrical Code, ANSI/
NFPA 70 provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT (NEC
SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the copyright
laws of the United States and that prior permission be obtained from copyright owners
whenever copying tapes or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated on
the back of the set.
2
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE
TO YOUR SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery eletrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING on page 18. If
you can’t resolve the problem, or if the product is damaged, refer to the LENOXX
WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch
your skin, and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a CD
4
1
2
3
Connect the supplied AC power cord or batteries(see page 14).
Slide the Function Switch to CD
position (power on).
1
2
RADIO
CD
TAPE
Press the CD Door Open
button to open the CD Door
and place the CD in the CD
compartment.
CD OPEN
The label side of the CD
should face you.
Close the CD door by pushing it
back.
3
4
Press the CD Play
Button. The player plays
all the tracks once.
Track
number
Play/Pause
Lamp
4
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
Volume Control
Function
Switch
CD Open
Button
Tip
When CD play is
To
Press or Adjust
paused, the Play/
Pause Lamp will
flash and no music
will play.
Adjust the volume
Stop playback
Volume Control
To resume play,
press the Pause
Button again, the
Play/Pause Lamp
will stop flashing
and music will play.
Pause playback
The Lamp will flash during
pause. Press again to
resume play after pause.
Go to the next track
Go back to the previous
track
Play/Pause Lamp
or
while playing,
Locate a point in a song
press and hold down until
you find the point.
CD door Open Button
(press Stop first)
Remove the CD
Slide the Function Switch
to TAPE position
Turn off the power
5
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CD tracks repeatedly (Repeat Play)
You can play CD tracks repeatedly in normal or program play modes (see page 7).
Function Switch
Repeat Button
Repeat Lamp
Program Lamp
1. Slide the Function Switch to CD position.
2. Press the CD Repeat Button.
To repeat
Press
Repeat Lamp
a single track (song)
all the tracks (songs)
Press the Repeat Button once
Press the Repeat Button twice
Flashing
Steady on
programmed tracks
Press the Program Button, and
then the Repeat Button twice
Steady on
(the Program
Lamp flashing)
3. Select the track by pressing
or
, and then press
.
To cancel Repeat Play
Press the Repeat Button until the Repeat Lamp is off.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Creating your own music
program (Program Play)
Program
You can make a program of up to 19
tracks in the order you want them to be
played.
Program Lamp
1. Slide the Function Switch to CD position.
2. Press the Program Button. The number “ ” and the
Program Lamp will flash.
3. Press
or
to select the tracks you want to
program in the order you want.
4. Press the Program Button to confirm. The number “ ”
and the Program Lamp will flash.
5. Repeat steps 3 and 4. You can program up to 19
tracks.
6. Press
to start program play. The Program Lamp will
remain flashing.
To change the current program
Just creat a new program following the Programing procedure.
To cancel Program Play
Press the Stop Button and the Program Lamp goes off.
7
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the radio
2
3
4
1
Connect the supplied AC power cord or batteries (see page 14).
Slide the Function Switch to
RADIO position (power on).
1
2
CD
RADIO
TAPE
Slide the Band Switch to the proper
band position that you want.
FM
AM
FM ST.
BAND
3
4
Tune into the station you prefer
using the Tuning Control. Adjust
for the clearest sound.
This indicator will light up when
receiving FM Stereo broadcasts.
FM STEREO
8
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
Volume Control
Function Switch
Tip
To
Slide or Adjust
If the FM broadcast is
•
Adjust the volume
Volume Control
noisy, slide the Band
Switch from FM Stereo
to FM position.
Slide the Function Switch
to TAPE position
Turn off the Radio
To improve broadcast reception
Reorient the antenna for FM or FM Stereo. Reorient
the player itself for AM.
9
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a tape
3
2
Connect the supplied AC power cord or batteries(see page 14).
Slide the Function Switch to
TAPE position.
1
CD
RADIO
TAPE
Press the Stop/Eject
Button to open the tape
2
compartment
and
insert a recorded tape.
Close the door.
STOP/EJECT
Full reel on
the left side.
Press the Play Button.
The player truns on and starts
playing.
3
PLAY
10
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
VOLUME CONTROL
PHONES
JACK
BASS BOOST
SWITCH
PAUSE
STOP/EJECT
PLAY
FAST F.&
REWIND
To
Press or Adjust
Volume Control
Tip
Adjust the volume
Stop playback
When the tape finishes
playing that side of the
tape, the set will stop. To
hear the otherside, flip
tape over, then insert
and press Play.
Stop/Eject Button
Fast forward or rewind the
tape
Fast Forward Button or
Rewind Button
Pause playback
Pause Button
Press again to resume
play after pause.
Eject the cassette
Stop/Eject Button
Bass Boost Switch
Get different sound effect
To enjoy the music without
distrubing others
Insert your headphone
plug into the Headphone
Jack (marked PHONES)
11
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a tape
2
3
1
Connect the supplied AC power cord or batteries (see page 14).
1
2
Press the Stop/Eject Button to
open the tape compartment
and insert a blank tape. Select
the program source (AM, FM,
CD, or, built-in microphone)
you want to record.
STOP/EJECT
To record from the CD player,
insert a CD and follow the steps to
play a CD (see page 4).
To record from a radio, slide the
Function Switch to RADIO, and
tune into the station you want (see
page 8).
CD
RADIO
TAPE
To record from the buit-in
microphone, leave the Function
Switch at TAPE position, and
speak in front of the set.
Press the Record Button to start
recording. (The Play Button is
depressed automatically.)
3
RECORD
12
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
Tip
FUNCTION
SWITCH
STOP/EJECT PAUSE
• Adjusting the Volume or
Bass Boost Switch will
not affect the recording
level.
• For best recording
effect, use the AC
power instead of
batteries.
To
Press or Adjust
Stop recording
Stop/Eject Button
Pause recording
Pause Button
Press the button again to
resume recording.
• To erase a recording,
just start a new
recording, and the old
one is automatically
replaced.
Turn off the power
Press the Stop/Eject
Button and slide the
Function Switch to TAPE
position.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Choosing the power sources
You can use the AC power or batteries as a power source.
Tip
1. Connecting the AC power
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again. This
plug is polarized and only fits
one way into the wall outlet
and back of the set.
cord
Insert one end of the supplied AC power cord to
the socket located at the rear of the player, and
the other end to the wall outlet.
2. Using the player on batteries
Insert 8 size “C” batteries (not supplied) into the
battery compartment.
Tip
Replace the batteries when
the Power/Battery Lamp dims
or when the player stops
operating. Replace all the
batteries with new ones.
Before you replace the
batteries, be sure to take out
the CD from the player and
remember to check the
Battery Safety Instructions on
Page 3.
To use the player on batteries, disconnect the AC
power cord from the player.
8
S IZ
E
“C ” B A T T E R IE S
U P P E R
LO E R
W
B AT T E R Y D O
O
R
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Precautions
On safety
On power sources
As the laser beam used in the CD
For battery operation, use 8 size C
•
•
player section is harmful to the eyes,
do not attempt to disassemble the
casing. Refer servicing to qualified
personnel only.
batteries. We recommend alkaline
batteries for longer life.
When the batteries are not to be used,
•
remove them to avoid damage that can
be caused by battery leakage or
corrosion.
Should any solid object or liquid fall into
•
the player, unplug the player, and have
it checked by qualified personnel
before operating it any further.
The nameplate indicating operating
voltage, power consumption, etc. is
located at the back of the set.
•
On placement
On operation
Do not leave the player in a location
If the player is brought directly from a
•
•
near heat source, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In this
case, remove the CD and wait about
an hour for the moisture to evaporate.
If the player has not been used for a
long time, set it in the playback mode
to warm it up for a few minutes before
insert a cassette.
Do not place the player on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The ventilation
holes must be unobstructed for the
player to operate properly and prolong
the life of its components.
If the player is left in a car parked in
•
This CD player is designed to be played
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the sun.
•
on a stable no vibration position. If you
bump the set during CD play, the music
will stop or skip for a few seconds. This
is normal for this type of player.
Since a strong magnet is used for the
•
speakers, keep personal credit cards
using magnetic coding or spring-
wound watches away from the player
to prevent possible damage from the
magnet.
If you have any questions or problems
concerning your player, please contact
our Customer Service Department at
•
1-800-315-5885 (MONDAY - FRIDAY
09:00 - 17:00 EST).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Precautions (continued)
Notes on CDs
Notes on cassettes
Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
Break off the cassette tab from side A
•
•
or B to prevent accidental recording. If
you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
Side A
Tab for side A
Tab for side B
Do not use solvents such as benzene,
•
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
Do not expose the CD to direct
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
Do not stick paper or sticker on the
CD, nor scratch the surface of the CD.
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
To reduce the chances of tape jamming
•
•
or tangling, you should check that
there are no loose layers of tape visible
through the cassette center window
if any, tighten these loose layers of
tape using a pencil before inserting the
cassette into the set.
After playing, store the CD in its case.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause tracking error.
16
CD-108072799 v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the lens
Notes for storing cassette
tapes
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner blower.
1. Do not put a tape near a magnetic field,
such as a TV, or speaker. Magnetic
fields may reduce the tape sensitivity
or even erase the recording.
2. Do not store tape for any length of time
in a hot, moist or dusty place.
Cleaning the tape heads
and tape path
Cleaning the cabinet
Wipe the heads, the pinch roller and the
capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type
of abrasive pad, scouring powder, or
solvent, such as alcohol or benzene.
RECORD / PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
CAPSTAN
COTTON SWAB
After cleaning, insert a tape when the
areas cleaned are completely dry.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Troubleshooting
Problem
Remedy
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the Function Switch is at the
right position as you want.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
“
” appears in the display
Insert the CD with the label side facing you.
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
•
CD does not play.
Place the CD with the label side facing you.
Clean the CD.
Take out the CD and leave the CD door
open for about an hour to dry moisture
condensation.
•
•
•
Make sure the Function Switch is at CD
position.
•
Clean the CD, or replace it if the CD is
badly damaged.
•
The sound drops out.
Place the player in a location free from
vibration.
•
Check if your batteries are fresh.
•
•
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
The sound is weak or has poor
quality.
The Record Button does not
function / The tape does not
play.
Make sure the safety tab on the cassette
is in place.
Make sure the Function Switch is at TAPE
position.
•
•
Clean the erasing head (see page 17).
Replace all the batteries with new ones if
they are weak.
The tape does not erase
completely.
•
•
Make sure the tape is inserted properly.
Make sure the safety tab of the cassette
is in place.
•
The tape does not record.
•
The sound is weak / The sound
quality is poor.
Clean the heads, pinch roller and capstan
(see page 17).
•
The tape has reached its end. Remove it,
flip to the other side and re-insert.
Cassette Play Button pops up.
•
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
Specification
GENERAL DESCRIPTION
Power source:
AC 120V, 60Hz 12Watts
DC 12V (8 size “C” batteries)
(we recommend alkaline batteries for longer life)
Speakers:
4” 8 ohm
Output power:
Dimensions:
2W / channel
1
Width: 16 / ”
4
1
3
Depth: 8 / ”
4
Height: 5 / ”
4
Weight: 7LBs (without batteries)
CD SECTION
Plays disc type:
Any normal CD used in portable players
760 - 800 NM
Laser wavelength:
Tracking method:
3 - spot error detection
3.86 mm lens
Frequency response: 40 Hz - 18 KHz
TAPE RECORDER SECTION
Tape:
Standard normal bias cassette tape
Frequency response: 100 Hz - 10 KHz
RADIO SECTION
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 KHz
LENOXX reserves the right to make design and specification changes for product
improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED UNDER
THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.
© 1999 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-108072799 v.1 E
|