LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES
CLEAN FACE PANEL KITS
(PAINTED FINISH)
P/N 504,223M
REV. F 03/2008
INSTALLATION INSTRUCTIONS FOR CLEAN FACE PANEL KITS FOR USE WITH
®
™,
™
MERIT MERIT PLUS OR ELITE SERIES GAS FIREPLACES
KIT CONTENTS:
TOOLS REQUIRED:
None
CAT. NO.
88L36
MODEL
WHERE USED
1 ea. Top Radiant Panel
1 ea. Bottom Radiant Panel
1 ea. Lennox Nameplate
1 ea. Instruction Sheet
EDV3530, ED3530 front-open, MPD3530,
MPD35ST/PF, MPB35ST
RAD35C-2
EDV4035, ED4035-2, MPD4035 front open,
EDVST, EDST-2, EDVPF, EDPF-2, EDVCR,
EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF,
EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2
multi-open (long panel)
88L37
RAD40C-2
Top Radiant Panel
CAUTION
88L38
88L35
RAD45C-2
RAD24C-2
EDV4540, ED4540-2, MPD4540 front-open
INSTALL ONLY WHEN THE
FIREPLACE IS OFF AND COLD!
EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2,
EBVCL, EBCL-2 multi-open (short panel)
Bottom Radiant Panel
MDR3328, MDT3328, MPDT3328,
MPDR3328
98L12
RAD33C
GENERAL INFORMATION
™
™
These clean face panel kits may be used with Merit , Merit Plus or
Elite series gas fireplaces listed in Table 1.
26M47
H7019
RAD33MC
RAD22C-2
MPD3530, MPD35ST
MPD35PF
®
Table 1 - Painted Panel Kits
INSTALLATION INSTRUCTIONS
Note: Donotoperatefireplacewithouttheeyebrowinstalledinitsnormal
position. See Figure 1 for models with louvers or Figure 2 for
models with clean face panel.
Top of Appliance
Louver Assembly
Step 1.Grasp the existing eyebrow and pull it forward away from the
fireplace (it is held in place by spring tension). See Figure 1.
Step 2.Slightly lift and pull the existing top louver assembly away from
the fireplace.
Step 3.Slide the existing eyebrow into the slots on the lower edge of the
top radiant replacement panel.
Top of Door Frame
Step 4.Hang the top radiant panel/eyebrow assembly in the opening
previously occupied by the top louver assembly. See Figure 2.
Step 5.Open the bottom louver assembly by pushing in simultaneously
the left and right sides of the louver assembly (the assembly is
hinged at the bottom).
Hood must be installed as shown.
Figure 1 - Louvered Face
Step 6.Merit Series Units - Remove the assembly from the fireplace by
removing the hinge screw and spacer on each end of it.
Merit Plus and Elite Series Units - Remove the assembly from the
fireplace by sliding the hinge pin, located at the door’s left side,
to the right until it disengages from the left corner post hole. Pull
the door diagonally to the left, away from the fireplace.
Step 7. Snap the replacement Lennox nameplate logo into the 2 holes
provided in the replacement panel.
Top of Appliance
Top Radiant Panel
Top of Door Frame
Step 8. Merit Series Units - Install the replacement bottom radiant panel
using the existing hinge screws and spacers.
Merit Plus and Elite Series Units - Install the replacement bottom
radiant panel by inserting the right side locating pin into the right
cabinet corner post and then the left side spring-loaded pin into
the left cabinet corner post.
Hood must be installed as shown.
Figure 2 - Clean Face
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2001 by Lennox Hearth Products
Lennox Hearth Products
1110 West Taft Avenue • Orange, CA 92865
P/N 504,223M REV. F 03/2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|