LCD Display Legend
Bad Cell Detection
When charge process is started, the charger detects the health status of each of the cells in
the battery compartment. If any batteries are unsuitable for charging, i.e. short circuit or
reversed polarity, the word “BAD” will indicate on the LCD screen and ”battery” icon will flash.
R2G802U
USB Charge Port Operation
When using the USB PowerPort on this charger, the AA/AAA charger function has priority.
The USB PowerPort will not be available while batteries are installed and charging. Once the
AA/AAA batteries have completed their charge, the USB port will be turned on automatically.
The “USB symbol” will be shown on the LCD screen to indicate the USB socket is
ready for use.
Fig. 1
Note: Make sure the maximum loading is not exceeding 500mA for the USB socket. Do not
attempt to overload the USB port or damage to the charger or USB device may result.
PLEASE READ THE INFORMATION AND FOLLOW ALL INSTRUCTIONS THOROUGHLY BEFORE
USING THIS PRODUCT.
Getting Ready
Choose the adapter plate for the type of battery you will be charging. Each of the adapter
plates is labeled as to the batteries it can work with. If the charger base does not already
have the adapter plate you want attached, you will need to remove the adapter plate first
by pushing down on the plate and sliding it to the rear of the charger base (away from
the LED indicators). Then, attach the selected adapter plate to the charger unit by
aligning the arrows on the sides of the adapter plates and the charger base as shown.
While pressing down lightly on the adapter plate, slide the plate toward the front of the
charger base until it locks.
Introduction
Clock / Alarm / Day-Date operation
Thank you for purchasing the R2G802 2 Hour Charger. Read the instruction manual
thoroughly before use and keep the manual for later reference. It contains important
operating instructions for your R2G Rechargeable Battery System. The R2G802 is a
combination of Travel Alarm Clock, 2 hour microprocessor controlled charger for 1 to 4
AA/AAA NiMH batteries, Thermometer, and USB PowerPort for charging your cell
phones, MP3 players or any other device that accepts power from a USB port. All the
functions are displayed clearly on a large backlit LCD Display. The charger can be
powered 3 ways and includes a high efficiency “switching” type power supply will adjust
automatically to any voltage from 100 – 240VAC, for international use. A car-cord for
using the charger in the car and a USB cable for powering the charger from your
computer are also included.
The following shows which buttons on the setting panel you need to press to navigate
between modes. The 2 feet on the bottom rear of the chassis act as switches to activate the
blue backlight on the LCD display. In any mode, just to hit the top of the unit lightly and the
black light will light on for about 10 seconds. The backlight will only operate while the unit is
plugged into power using any of the supplied power adapters.
Charging Instructions
Setting the Time and Date
Fig. 2
1. Choose the source of power for the charger unit. You can use the AC adapter which
is international capable accepting 100-240VAC (plug adapter may be required in other
countries, not included), the DC car cord while on the move or plugged into a USB port
on your computer (charge times are increased when USB power is used). Simply plug
the desired power cable into the side of the charger unit and the other end into the
appropriate power source.
Before Use
To activate the clock and thermometer functions, pull out the tab from the side of the
casing at the access cover to the clock battery on the bottom of the unit. The clock
portion of the LCD display will turn on and you will hear alarm music for 10 seconds. The
Clock / Alarm is now ready for use and should be set to the proper time / date. If the LCD
display get dim or the sound of the alarm tone become weak, replace the clock battery
with another new “CR-2025” type 3V Lithium battery which is located on the bottom side
of the charger base.
B
In the regular Time mode, press the
button once and the “Time” icon will starts to flash on
2. Insert 1 to 4 pieces of AA or AAA rechargeable Ni-MH batteries into any open battery
location observing the proper battery polarity to the marks in the battery compartment.
Do not mix AA and AAA batteries while charging. The Blue backlight will light up for
around 10 sec once the batteries inserted correctly. For charging AAA batteries, pull
down the adjustable battery contact plate before inserting the AAA batteries into the
compartment. The charger automatically adjusts the charging current depending on the
size of the battery being charged.
the LCD screen along with the item to be changed, which indicates Time Setting mode. Use
C
and
what you want, press
can be set in the range of 2000 to 2099. The day of the week is calculated automatically
D
buttons to change the value of the flashing item. Once the flashing item is set to
B
to select the next setting and change as listed above. The “Year”
A
according with the date you set. Once all the items are set, press the
button to exit the
Caution:
setting mode (set mode will automatically if there is no input for 1 minute). The following figure
shows the order of items during the setting process.
•
Batteries are partially charged as shipped. Must be charged prior to first use for full
capacity.
3. The LCD will indicate the proper charging and the word “Charge” will be shown to the
left of the battery symbols that indicate each battery’s charge progress. After the
batteries are fully charged, the wording “FULL” will indicate on the LCD screen to
indicate the trickle charge and the charged batteries are ready for use. Once charge is
complete, remove batteries and unplug the charger as soon as it is practical. Do not
leave batteries in charger for extended periods of time (more than 1-2 days) or when the
charger is not plugged in. Unplug the charger when not in use.
•
•
•
Charge only NiMH type batteries on this charger.
Do Not mix AA and AAA or different capacity batteries together when charging
Use only R2G, NoMEM PRO or other proper NiMH compatible charger to recharge
the batteries included.
Fig. 3
•
Batteries may leak or explode causing personal injury if inserted improperly, disposed
of in fire, mixed with other battery types, or short circuited.
12/24 Hour Mode:
C
In the regular Time mode, pressing the
24-hour mode.
button will toggle between 12-hour and
4. Begin again at Step-1 to charge the next set of batteries.
2.
1.
3.
Download from Www.Somanuals.com. All Manuals Search And Download.
|