Land Pride Paper Shredder 330 114A RC RCM5020 User Manual

Baffle and Shredder Kits  
For RC(M)5020 Rotary Cutters  
Manual No. 330-148M  
Before You Start  
Safety Information  
When you see this symbol, the subsequent  
!
WARNING  
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
!
Never work under equipment supported by hydraulics.  
Hydraulics can drop equipment if controls are actuated or if  
hydraulic lines burst. Either situation can drop the cutter  
instantly even when power to the hydraulics is shut off.  
IMPORTANT: Before you begin, read these  
instructions and check to be sure all parts and tools  
are accounted for. Please retain these installation  
instructions for future reference and parts ordering  
information.  
!
DANGER  
Always disconnect main driveline from tractor PTO before  
servicing the cutter deck. Cutter can be engaged if tractor is  
started resulting in damage to the cutter, bodily injury and/or  
death.  
The Baffle Kit and Shredder Kit are exclusively designed  
for your 20 foot Land Pride Rotary Cutter. Please read  
these installation instructions and your Rotary Cutter  
Operator’s Manual thoroughly before beginning.  
Especially read information relating to safety concerns.  
Also included in the Operator’s Manual is important  
information on operation, adjustment, troubleshooting,  
and maintenance for this attachment (some manual  
sections do not apply to all accessories).  
Baffle Assembly Instructions  
A detailed listing of parts for the Baffle and Shredder Kits  
is provided on page 6. Use the list as a checklist to  
inventory parts received. Please contact your local Land  
Pride dealer for any missing hardware.  
A separate Rotary Cutter Parts Manual is available free  
from your nearest Land Pride dealer. Have the model  
and serial numbers of your cutter handy when placing an  
order.  
IMPORTANT: Read “Safety Information” above  
before installing baffle plates.  
1. Lower cutter and wings to the lowest position.  
2. Place tractor gear selector in park and/or set brakes,  
shut engine off and remove ignition key.  
Manual Part Numbers:  
Operator’s Manual . . . . . . . . . . . . . . . . . 318-474M  
Parts Manual . . . . . . . . . . . . . . . . . . . . . 318-474P  
3. Disconnect main driveline from tractor PTO.  
Refer to Figure 1 on page 2:  
4. Locate and drill twelve 9/16" dia. holes on each wing  
deck as shown in Figure 1.  
General Information  
These assembly instructions apply to the Baffle and  
Shredder Kits listed below:  
NOTE: Drilling holes is not necessary on models  
manufactured after serial # 536743.  
330-114A  
318-958A  
RC/RCM5020 BAFFLE KIT  
5. The wings can be raised and locked into position for  
the remainder of the assembly.  
RC/RCM5020 SHREDDER KIT  
Refer to Figure 2 on page 3:  
6. Attach the four front baffles (#4) to each wing deck  
with 1/2"-13 x 1 1/2" GR5 hex head bolts (#5), 1/2"  
flat washers (#7) and 1/2" hex whiz nut (#6).  
Tools required:  
Safety Glasses  
Work Gloves  
7. Torque nuts to 76 ft-lbs.  
Tape measure . . . . . . . . . . . . . . . . . . . .Baffle Kit Only  
Pencil . . . . . . . . . . . . . . . . . . . . . . . . . . .Baffle Kit Only  
Center Punch . . . . . . . . . . . . . . . . . . . . .Baffle Kit Only  
Hammer . . . . . . . . . . . . . . . . . . . . . . . . .Baffle Kit Only  
Drill with 9/16" Drill Bit . . . . . . . . . . . . . .Baffle Kit Only  
Extension Cord . . . . . . . . . . . . . . . . . . . . . . if required  
Two 3/4" wrenches . . . . . . . . . . . . . . . . .Baffle Kit Only  
Two 1 1/2" wrenches . . . . . . . . . . . . Shredder Kit Only  
One 55mm wrench . . . . . . . . . . . . . . Shredder Kit Only  
IMPORTANT: The rear baffle is installed with the  
same bolts attaching the rear guard. Do not remove  
rear guard.  
8. Remove nuts securing the rear guard and attach rear  
baffle plate (#1) to the inside of the rear deck plate  
using existing hex whiz nuts. Do not remove rear  
guard.  
© Copyright 2007  
Printed  
8/20/07  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Land Pride  
Baffle Assembly Instructions  
10. Torque nuts to 76 ft-lbs.  
9. Install 1/2"-13 x 1 1/2" GR5 round head square neck  
bolt (#2) and 1/2" hex whiz nut (#6) as shown in  
Figure 2.  
24860  
Baffle Installation (Left Wing Shown)  
Figure 2  
8/20/07  
Manual No. 330-148M  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Shredder Assembly Instructions  
Shredder Assembly Instructions  
A detailed listing of parts for this accessory kit is provided  
on page 6. Use the list as a checklist to inventory parts  
received. Please contact your local Land Pride dealer for  
any missing hardware.  
Center Deck & Left Wing Shredder Assy  
Refer to Figure 4:  
1. Attach center deck and left wing shredder  
assemblies (#2) to gearbox output shafts (B) with  
existing washer (C) and slotted hex nut (D). Torqued  
slotted nut to 550 ft./lbs.  
IMPORTANT: Read “Safety Information” on page 1  
before installing shredder blades.  
2. Install cotter pin (E) in the slotted nut with legs  
securely bent around the nut.  
Refer to Figure 3:  
1. Remove all three existing blade carrier assemblies  
from the gearbox output shafts (A & B). Keep flat  
washers C), slotted hex nuts (D) and cotter pins (E)  
for reuse.  
Right Wing Shredder Assembly  
Refer to Figure 3:  
1. Attach right wing shredder assembly (#1) to gearbox  
output shaft (A) with existing washer (C) and slotted  
hex nut (D). Torqued slotted nut to 550 ft./lbs.  
2. Install cotter pin (E) in the slotted nut with legs  
securely bent around the nut.  
Counterclockwise Rotation  
Clockwise Rotation  
25601  
25601  
Right Wing Shredder Assembly  
Figure 3  
Center Deck & Left Wing Shredder Assemblies  
Figure 4  
Manual No. 330-148M  
8/20/07  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Shredder Assembly Instructions  
1.  
2.  
Replacing Blade Spacers  
Refer to Figure 5:  
The cutting blades should not have more than 3/4" free  
vertical movement at the blade tips. If vertical movement  
exceeds 3/4", install or change to thicker spacers (#3)  
following steps 1 through 5.  
Check blade deflection. If vertical deflection at the  
blade tip is greater than 3/4", remove blade bolt (#6)  
and reassemble using thicker spacers (#3). Select  
spacer thickness based on deflection. The greater  
the deflection, the thicker the spacer.  
Assemble blades by inserting 1"-8 x 4 1/2" GR8 hex  
head bolt (#6) through blade bushing (#4), spacer  
(#3), lower cutting blade (#8 or #10), blade carrier  
(#5), upper flat cutting blade (#9), spacer (#3) and  
blade bushings (#4). Temporary secure blade with a  
plain hex nut (Plain hex nut furnished by customer.)  
Draw nut up snug. Do not tighten.  
Order spacers (#3) and locknuts (#7) from your nearest  
Land Pride Dealer.  
IMPORTANT: Read “Safety Information” on page 1  
before disassembling the shredder blades.  
3.  
4.  
Check blade deflection. If deflection at the blade tips  
are greater than 3/4", remove blade bolt and  
reassemble as before except use thicker spacers.  
IMPORTANT: Locknuts can lose their ability to lock  
properly once removed. Always use a plain throw  
away nut during pre-assembly of spacers.  
Once blade deflection is correct, replace plain nut  
with supplied locknut (#7) & torque to 450 ft-lbs.  
5. Repeat instructions for “Replacing Blade Spacers”  
for the remaining shredder blade assemblies.  
IMPORTANT: Spacers (#3) are not required if  
vertical movement at blade tip is 3/4" or less without  
spacers. However, spacers are required if vertical  
movement at blade tip is greater than 3/4".  
25600  
Blade  
Cutting  
Edge  
Position Beveled  
Edges Down  
CCW  
Rotation  
Blade  
Cutting  
Edge  
CW  
Rotation  
Blade Cutting Edges  
Position Beveled Edges Up  
(#2) Center Deck & Left Wing Shredder Assemblies  
Counterclockwise Rotation  
(#1) Right Wing Shredder Assembly  
Clockwise Rotation  
Figure 5  
8/20/07  
Manual No. 330-148M  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Listing of Parts  
Kit No. 330-114A  
RC5020 BAFFLE ASSEMBLY KIT  
Item Qty. Part No. Part Description  
Refer to Figure 2 on page 3:  
1
2
2
2
330-148M  
318-769D  
802-106C  
803-037C  
330-095H  
802-091C  
803-037C  
804-016C  
BAFFLE KIT INSTALLATION MANUAL  
PLATE, REAR BAFFLE  
RHSNB 1/2-13X1 1/2 GR5  
NUT HEX WHIZ 1/2-13 PLT  
BAFFLE 5020  
HHCS 1/2-13X1 1/2 GR5  
NUT HEX WHIZ 1/2-13 PLT  
WASHER FLAT 1/2 SAE PLT  
1
2
3
4
5
6
7
8
24  
24  
24  
Kit No. 318-958A  
RC5020 SHREDDER ASSEMBLY, COMER  
Item Qty. Part No. Part Description  
Refer to Figure 3 & Figure 4 on page 4:  
1
1
2
330-148M  
318-859S  
318-860S  
BAFFLE KIT INSTALLATION MANUAL  
ASSY. CW BLADE CARRIER 84"  
ASSY. CCW BLADE CARRIER 84"  
1
2
Refer to Figure 5 on page 5:  
(#1) Components for 318-859S CW Blade Assembly (Quantities shown are for one Assembly)  
3
3
3
3
4
5
6
7
9
4
4
4
4
4
1
2
2
2
2
312-075D  
312-082D  
312-089D  
312-808D  
318-309D  
330-209H  
802-680C  
803-168C  
820-216C  
820-249C  
BLADE SPACER 16 GA  
BLADE SPACER 18 GA  
BLADE SPACER 20 GA.  
BLADE SPACER 24GA  
BLADE BUSHING  
BLADE BAR  
HHCS 1-8 X 4 1/2 PLT GR8  
NUT HEX TOP LOCK 1-8 PLT  
A maximum of four spacers  
are used per assembly.  
CUTTER BLADE 1/2X4X28.5 FLAT  
CUTTER BLADE 1/2X4X29 CW  
10  
Refer to Figure 5 on page 5:  
(#2) Components for 318-860S CCW Blade Assembly (Quantities shown are for one Assembly)  
3
3
3
3
4
5
6
7
8
9
4
4
4
4
4
1
2
2
2
2
312-075D  
312-082D  
312-089D  
312-808D  
318-309D  
330-209H  
802-680C  
803-168C  
820-168C  
820-216C  
BLADE SPACER 16 GA  
BLADE SPACER 18 GA  
BLADE SPACER 20 GA.  
BLADE SPACER 24GA  
BLADE BUSHING  
BLADE BAR  
HHCS 1-8 X 4 1/2 PLT GR8  
NUT HEX TOP LOCK 1-8 PLT  
A maximum of four spacers  
are used per assembly.  
CUTTER BLADE 1/2X4X29 CCW  
CUTTER BLADE 1/2X4X28.5 FLAT  
Corporate Office: P.O. Box 5060  
Salina, Kansas 67402-5060 USA  
Manual No. 330-148M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8/20/07  
6

Life Fitness Elliptical Trainer 91XW 0XXX 01 User Manual
Lincoln Electric Welder SVM175 A User Manual
Lindy Computer Drive 51072 User Manual
Little Tikes Baby Gym Baby Gym User Manual
Loewe TV Antenna Connect 32 Full HD+ 100 User Manual
LOREX Technology Security Camera SG4934W Series User Manual
Magnavox DVD Player DP100MW8B A User Manual
Memorex MP3 Player MMP3682 User Manual
Mercedes Benz Automobile 2003 E 320 User Manual
Metrologic Instruments Scanner MS7100 User Manual