Land Pride Lawn Mower Accessory fd1548 User Manual

Ope ra tor’s Ma nua l  
FD1548 & FD1560  
3-Spindle Grooming Mower  
Read the Operator’s manual entirely. When you see this symbol, the subsequent instruc-  
tions and warnings are serious - follow without exception. Your life and the lives of others  
depend on it!  
!
10618  
Cover illustration may show optional equipment not supplied with standard unit.  
© Copyright 2008 Printed  
310-155M  
7/18/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Important Safety Information  
Important Safety Information  
Keep Riders  
Off Machinery  
Riders obstruct the operator’s  
view they could be struck by  
foreign objects or thrown from the  
machine.  
Be Aware of Signal Words  
The word that designates a degree  
or level of hazard seriousness. The  
signal words are:  
!
WARNING  
situation which, if not avoided, could  
result in death or serious injury, and  
includes hazards that are exposed  
when guards are removed. It may  
also be used to alert against unsafe  
practices.  
!
DANGER  
Indicates an imminently hazardous  
situation which, if not avoided, will  
result in death or serious injury. This  
signal word is limited to the most  
extreme situations, typically for  
machine components that, for  
functional purposes, cannot be  
guarded.  
Never allow children to operate  
equipment.  
!
Idicates a potentially hazardous  
CAUTION  
situation which, if not avoided, may  
result in minor or moderate injury. It  
may also be used to alert against  
unsafe practices.  
Indicates a potentially hazardous  
!
For Your Protection  
Thoroughly read and understand  
the “Safety Label” section, read all  
instructions noted on them.  
Shutdown and Storage  
Lower machine to ground, put  
tractor in park, turn off engine,  
and remove the key.  
OFF  
Detach and store implements in a  
area where children normally do  
not play. Secure implement by  
using blocks and supports.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Land Pride  
Important Safety Information  
Use the following maximum  
Use Safety  
Lights and Devices  
Transport  
Machinery Safely  
speed - tow load weight ratios as  
a guideline:  
20 mph when weight is less than  
Slow moving tractors, self-  
propelled equipment, and towed  
implements can create a hazard  
when driven on public roads. They  
are difficult to see, especially at  
night.  
Flashing warning lights and turn  
signals are recommended  
whenever driving on public roads.  
Use lights and devices provided  
with implement.  
Comply with state and local laws.  
or equal to the weight of tractor.  
Maximum transport speed for  
implement is 20 mph. DO NOT  
EXCEED. Never travel at a speed  
which does not allow adequate  
control of steering and stopping.  
Some rough terrains require a  
slower speed.  
Sudden breaking can cause a  
towed load to swerve and upset.  
Reduce speed if towed load is not  
equipped with brakes.  
10 mph when weight is double  
the weight of tractor.  
IMPORTANT: Do not tow a load  
that is more than double the  
weight of tractor.  
Practice Safe Maintenance  
Move the opener handle to the  
“ROAD” position and complete  
raising the openers to lock them  
up before working underneath  
them.  
Understand procedure before  
doing work. Use proper tools and  
equipment, refer to Operator’s  
Manual for additional information.  
Disk edges are sharp. Be careful  
Work in a clean dry area.  
when working in this area.  
Lower the implement to the  
ground, put tractor in park, turn off  
engine, and remove key before  
preforming maintenance.  
Disconnect battery ground cable  
(-) before servicing or adjusting  
electrical systems or before  
welding on implement.  
Inspect all parts. Make sure parts  
are in good condition & installed  
properly.  
Allow implement to cool  
completely.  
Install all transport locks on raised  
drill before working underneath, refer  
to the Operator’s Manual for quantity  
and location of transport locks.  
Remove buildup of grease, oil or  
debris.  
Remove all tools and unused pars  
Do not grease or oil implement  
from implement before operation.  
while it is in operation.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Important Safety Information  
Wear  
Tire Safety  
Prepare for Emergencies  
Be prepared if a fire starts.  
Protective Equipment  
Tire changing can be dangerous  
and should be preformed by  
trained personnel using the  
correct tools and equipment.  
When inflating tires, use a clip-on  
chuck and extension hose long  
enough to allow you to stand to  
one side and NOT in front of or  
over the tire assembly. Use a  
safety cage if available.  
Protective clothing and equipment  
Keep a first aid kit and fire  
should be worn.  
extinguisher handy.  
Wear clothing and equipment  
appropriate for the job. Avoid  
loose fitting clothing.  
Prolonged exposure to loud noise  
can cause hearing impairment or  
hearing loss. Wear suitable  
hearing protection such as  
earmuffs or earplugs.  
Operating equipment safely  
requires the full attention of the  
operator. Avoid wearing radio  
headphones while operating  
machinery.  
Keep emergency numbers for  
doctor, ambulance, hospital and  
fire department near phone.  
When removing and installing  
wheels, use wheel handling  
equipment adequate for the  
weight involved.  
911  
Do not stand between the tractor  
Safety at All Times  
and implement during hitching.  
Thoroughly read and understand the  
instructions given in this manual  
before operation. Refer to the “Safety  
Label” section, read all instructions  
noted on them.  
Keep hands, feet, and clothing  
away from power-driven parts.  
Wear snug fitting clothing to avoid  
entanglement with moving parts.  
Watch out for wires, trees, etc.,  
when folding and raising  
Operator should be familiar with  
all functions of the unit.  
implement. Make sure all persons  
are clear of working area.  
Turning tractor too tight may  
cause implement to ride up on  
wheels. This could result in injury  
or equipment damage.  
Operate implement from the  
driver’s seat only.  
Do not leave tractor or implement  
unattended with engine running.  
Dismounting from a moving  
tractor could cause serious injury  
or death.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Important Safety Information  
sure the correct safety labels are included in the request. To  
order new labels go to your Land Pride dealer.  
5. Refer to this section for proper label placement.  
To install new labels:  
Safety Labels  
Your implement comes equipped with all safety labels in place.  
They were designed to help you safely operate your implement.  
1. Read and follow label directions.  
2. Keep all safety labels clean and legible.  
a. Clean the area the label is to be placed.  
b. Peel backing from label. Press firmly on surface  
being careful not to cause air bubbles under label.  
3. Replace all damaged or missing labels.  
4. Some new equipment installed during repair require safety  
labels to be affixed to the replaced component as specified  
by the manufacturer. When ordering new components make  
818-130C  
Caution: 540 RPM  
15037  
15037  
15038  
818-142C  
Danger: PTO Driveline  
818-230C  
Red Reflector  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Important Safety Information  
818-250C  
Caution: V-Belt Installation  
(FD1560)  
818-293C  
Caution: V-Belt Installation  
15036  
(FD1548)  
818-540C  
Danger: Guard Missing  
13102  
ROTATING DRIVELINE  
KEEP AWAY!  
818-552C  
Danger: Rotating Driveline  
13102  
818-555C  
Danger: Rotating Blades  
15038  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7/18/08  
5
Land Pride  
Important Safety Information  
818-556C  
Danger: Thrown Objects  
15038  
818-558C  
Warning: General Safety  
15036  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7/18/08  
6
Land Pride  
Introduction  
Introduction  
Land Pride welcomes you to the growing family of new  
product owners.  
These parts have been specially designed and should  
only be replaced with genuine Land Pride parts.  
This implement has been designed with care and built by  
skilled workers using quality materials. Proper assembly,  
maintenance, and safe operating practices will help you  
get years of satisfactory use from the machine.  
These parts have been specially designed and should  
only be replaced with genuine Land Pride parts.  
Serial Number Plate  
Refer to the Figure 1 for the location of your serial number  
plate.  
The parts on your FD15 Grooming Mower have been  
specially designed and should only be replaced with  
genuine Land Pride parts. Therefore, should your Rotary  
Cutter require replacement parts go to your Land Pride  
Dealer.  
Using This Manual  
This Operator’s Section is designed to help familiarize you  
with safety, assembly, operation, adjustments,  
troubleshooting, and maintenance. Read this manual and  
follow the recommendations to help ensure safe and  
efficient operation.  
The warranty Registration card should be filled out by the  
dealer at the time of purchase.  
To order a new Operator or Parts Manual contact your  
authorized dealer. You may obtain parts information from  
15031  
Serial Number Plate Location  
Figure 1  
The information contained within this manual was current  
at the time of printing. Some parts may change slightly to  
assure you of the best performance.  
For prompt service always use the serial number and model  
number when ordering parts from your Land Pride dealer.  
Be sure to include your serial and model numbers in  
correspondence also.  
Terminology:  
"Right " or "Left" as used in this manual is determined by  
facing the direction the machine will travel while in use  
unless otherwise stated.  
Your dealer wants you to be satisfied with your new  
machine. If for any reason you do not understand any part  
of this manual or are not satisfied with the service  
received, the following actions are suggested:  
Definitions:  
IMPORTANT: A special point of information related to  
its preceding topic. The author’s intention is that this  
information should be read and noted before  
continuing.  
1. Discuss the matter with your dealership service  
manager make sure he is aware of any problems you  
may have and that he has had the opportunity to assist  
you.  
NOTE: A special point of information that the author feels  
an operator must be aware of before continuing.  
2. If you are still not satisfied, seek out the owner or  
general manager of the dealership, explain the  
problem and request assistance.  
Owner Assistance  
3. For further assistance write to:  
If customer service or repair parts are required contact an  
Land Pride dealer. A dealer has trained personnel, repair  
parts and equipment needed to service the implement.  
Product Support  
Land Pride, Service Department  
1525 East North Street  
P.O. Box 5060  
Salina, Ks. 67402-5060  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Land Pride  
Section 1 Assembly and Setup  
Section 1 Assembly and Setup  
3. Mount the upper hitch bars (#1), to the front hitch  
Tractor Requirements  
plates on the mower frame using the 5/8" x 1 3/4" long  
bolts (#11), lock washers (#12) and hex nuts (#13).  
This mower is designed with a 3-Point category I hitch.  
Horse power rating of tractor should not exceed 26 PTO  
horse power.  
4. Remove the 5/8" x 5" long bolt (#5), lock washer (#6),  
and hex nut (#7) from the upper pivoting hitch  
subassembly.  
!
CAUTION  
5. Swing the upper hitch bars (#1) up to a vertical  
position. Raise the upper hitch braces (#2) up inside  
the upper hitch bars as shown.  
Do not over speed PTO or machine damage may result.  
NOTE: In order to maintain steering control, ballast  
may have to be added to your tractor front end. To  
determine whether or not to add ballast, refer to your  
tractor operator’s manual.  
6. Assemble the upper pivoting hitch (#3), spacer top  
hitch (#4), 5/8" x 5" long bolt (#5), lock washer (#6),  
and hex nut (#7).  
7. Place the chute (#14) over the square holes on the  
right hand side of the deck. Insert the 5/16" carriage  
bolts (#15) from the underneath side of the deck.  
Secure with the 5/16" nuts (#16) lock washers (#17)  
and flat washers (#18).  
Upper Hitch Arms Assembly  
Refer to Figure 1-1:  
1. Remove the upper hitch bars (#1), upper hitch braces  
(#2), and upper pivoting hitch subassembly (#3)  
through (#7) from storage position on top of mower  
deck.  
2. Bolt the upper hitch braces to the mounting tabs on  
back of the deck using 1/2" x 1 1/2" long bolts (#8),  
lock washer (#9), and hex nut (#10).  
4-Wheel Unit Upper Hitch Arms Assembly  
Figure 1-1  
15033  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Land Pride  
Section 1 Assembly and Setup  
4. Attach the chain from the PTO shield to one of the  
Tractor Hookup  
upper hitch braces to ensure that the shield does not  
rotate.  
1. Be certain that the tractor draw bar will not interfere.  
Move the draw bar ahead or remove if required. Draw  
bar should also be checked for clearance when the  
unit is being raised for the first time.  
5. Should the driveline require shortening:  
a. Hold the half-shafts next to each other in the  
shortest working position and mark them.  
2. Align the lower link arms of the tractor to the hitch  
clevises on the mower. Insert the lower hitch pins into  
the lower ball swivels and attach the lynch pins.  
b. Shorten inner and outer guard tubes equally.  
c. Shorten inner and outer sliding profiles by the  
same length as the guard tubes.  
3. Attach the tractor top link to the upper floating hitch on  
mower with the pin supplied. Secure with the lock pin.  
d. Proper overlap is a minimum of one-half the  
length of each tube, with both tubes being of equal  
length.  
4. Adjust the tractor top link in or out to place the upper  
hitch pin vertically above the lower hitch pins in to  
allow mower flotation.  
e. Round off all sharp edges and remove burrs.  
Grease sliding profiles.  
Driveline Installation  
1. Slide the driveline end with the extended safety cone  
over the splined shaft of the gearbox and secure with  
attaching device.  
!
CAUTION  
Tractor PTO shield and all mower guards must be in place at  
all times during operation!  
2. Slide the driveline over the tractor’s splined PTO shaft  
and secure with locking device of driveline.  
3. The driveline should now be moved back and forth to  
insure that it is secure on the PTO shaft of the tractor  
and mower gearbox.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Land Pride  
Section 2 Operating Instructions  
Section 2 Operating Instructions  
5. Mower blades will cut better at a faster blade speed  
than at reduced throttle.  
Before You Start  
In addition to design and configuration of equipment,  
hazard control and accident prevention are dependent  
upon the awareness, concern, prudence and proper  
training involved in its operation, transport, maintenance  
and storage of equipment. Before beginning to operate  
your mower, the following inspection should be performed.  
6. Mowing should not be done in wet conditions as grass  
will stick to blades and the under side of mower deck.  
7. After mowing the first 50 feet, stop and check to see  
that the mower is adjusted properly.  
Prestart Checklist  
8. DO NOT make sharp turns or attempt to back up while  
Read and follow the Safety Rules carefully, refer to  
mower is on the ground.  
RIemapdoarltlaonftthSeafTertaycItnorfoHromoaktiUopninsthtaertinSgecotniopnag1e 1.  
Assembly and Setup” on page 8, and all preparation  
9. DO NOT engage PTO with mower in the fully raised  
iRnestarducthtieonsO. perating Instructions” section starting on  
position. DO NOT engage PTO at full throttle.  
10. Grass is best cut when it is dry. Mowing wet grass can  
cause plugging resulting in grass clumps behind the  
mower.  
Lubrication” starting on page 14 to lubricate the mower  
aCsherecqkuthireedm. ower initially and periodically for loose bolts  
11. Grass should be mowed frequently as shorter  
clippings deteriorate faster.  
BMoalkteSiszuerseainlltghueardSsecatnidonsh7ieAldpspaernediinxploancep,argeefe1r9to.  
12. If mowing extremely tall grass, it is best to raise cutting  
height and mow the area, then lower cutting height  
and mow a second time at the desired height.  
GIemaprboortxaGnteSaraLfeutbyeI,nrfeofremr taotitohnesSteacrttiinogno5n page 1.  
Transporting  
IMPORTANT: Always disengage PTO before raising the  
mower to transport position.  
When raising the mower to the transport position, be sure  
that powershaft does not contact tractor or mower. Adjust  
the tractor’s 3-point hitch lift height so that the PTO shaft  
does not contact mower deck.  
MChaeinctke"nVa"nbceeltafonrdwLeuabr raincdatrieopnlacsetaifrtninegedoendpwaigtheL1a4n. d  
Pride part number 816-116C for FD1560 or 816-142C  
fCohreFcDk1f5o4r 8g.rass clippings built up in "V" belt drive area.  
Check that all plugs in gearbox have been replaced and  
tightened properly.  
Be sure to reduce tractor ground speed when turning; and,  
leave enough clearance so the mower does not contact  
obstacles such as buildings, trees or fences.  
!
CAUTION  
For Safety reasons, each maintenance operation must be  
performed with the tractor’s PTO disengaged, the mower  
lowered completely, tractor engine shut off and ignition key  
removed.  
Select a safe ground travel speed when transporting from  
one area to another. When traveling on roadways,  
transport in such a way that faster moving vehicles may  
pass you safely.  
Operating Instructions  
1. Clear the area to be mowed of rocks, branches and  
other foreign objects.  
When traveling over rough or hilly terrain, shift tractor to a  
lower gear.  
2. Lower mower to ground. Set tractor throttle at  
approximately 1/4 open. Engage PTO to start blades  
rotating.  
3. Operate with 540 rpm PTO tractor.  
4. At first begin mowing at a slow forward speed and shift  
up until the desired speed is achieved - maintaining  
540 PTO rpm.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Land Pride  
Section 3 Adjustments  
Section 3 Adjustments  
6. Rotate blades parallel to direction of travel.  
3-Point Hitch Adjustments  
7. Measure the clearance from the cutting edge to the  
ground at front and rear of the blade. This  
Refer to Figure 3-1:  
The 3-point hitch system on this mower has been  
designed for front to back flotation when mowing on  
uneven terrain. On the two wheel mower with fixed lower  
hitch pins and the four wheel mower with floating lower  
hitches in a mid position, adjust the tractor’s top link to  
place the upper hitch pin vertically above the lower hitch  
pins as shown below.  
measurement should be equal or have the blade at  
the front of the mower not more than 1/2" lower than  
the blade at the rear of the mower.  
Cutting Height Adjustment  
!
CAUTION  
Engage parking brake, shut off tractor, remove key and  
disengage PTO before making any height adjustment!  
Using the tractor, raise the mower off the ground and  
support under it with secure blocking so not to let the  
mower drift down during maintenance.  
Holding wheel and yoke assembly up, remove quick-lock  
pin from top of gauge wheel spindle. Position full length  
spacers and half spacer as required. All spacers on top of  
spindle tube allows for approximately 1" cutting height.  
Adjustments range from 1" to a maximum of 4" in 1/2"  
increments. Refer to "Leveling the Mower" beginning on  
this page.  
NOTE: If equipped with only rear gauge wheels, the  
mower must be leveled front to rear each time this  
adjustment is made.  
11910  
3-Point Assembly  
Figure 3-1  
Leveling the Mower  
NOTE: Tractor and mower should be on level ground.  
1. Set the lower hitches and upper floating hitch as  
shown in Figure 3-1.  
2. Start tractor and raise mower, watching that tractor  
draw bar (if not removed) does not interfere with  
mower.  
3. Slowly lower the mower until gauge wheels touch the  
ground and the lower mower 3-point hitch bars are  
parallel to the ground in floating position. Set tractor 3-  
point stop.  
4. Set park brake and turn off tractor. Remove key from  
ignition.  
5. Adjust the tractor top link in or out to place the upper  
hitch pin vertically above the lower hitch pin as to allow  
mower flotation.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Land Pride  
Section 3 Adjustments  
Transporting  
Belt Tension  
IMPORTANT: Always disengage PTO before raising  
the mower to transport position.  
Refer to Figure 3-2:  
!
CAUTION  
When raising the mower to the transport position, be sure  
that powershaft does not contact tractor or mower. Adjust  
the tractor’s 3-point hitch lift height so that the PTO shaft  
does not contact mower deck.  
Belt drive system under spring tension; use care to avoid bodily  
harm!  
1. To check tension apply force at arrow A. With a ten-  
sion tester and deflect the belt 1/4". The force required  
to get this deflection should range from 7 to 10 lbs.  
Be sure to reduce tractor ground speed when turning; and,  
leave enough clearance so the mower does not contact  
obstacles such as buildings, trees or fences.  
2. To adjust belt tension, adjust eyebolt (#1), as  
necessary. This adjustment will increase or decrease  
the tension on spring (#2).  
Select a safe ground travel speed when transporting from  
one area to another. When traveling on roadways,  
transport in such a way that faster moving vehicles may  
pass you safely.  
3. Excessive tension on the belt may lead to premature  
failure of belt and drive components. Excessive  
tension on the belt may also lead to a safety hazard to  
the operator or bystanders. Not enough tension on the  
belt may lead to premature failure of the belt due to  
excessive slipping.  
When traveling over rough or hilly terrain, shift tractor to a  
lower gear.  
!
CAUTION  
WHEN TRAVELING ON PUBLIC ROADS, WHETHER AT  
NIGHT OR DURING THE DAY, USE ACCESSORY LIGHTS  
AND DEVICES FOR ADEQUATE WARNING TO  
OPERATORS OF OTHER VEHICLES. COMPLY WITH ALL  
FEDERAL, STATE, AND LOCAL LAWS.  
!
WARNING  
Excessive tension on the belt may lead to premature failure of  
belt and drive components. Excessive tension on the belt may  
also lead to a safety hazard to the operator or bystanders.  
12732  
Belt Tension  
Figure 3-2  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Land Pride  
Section 4 Troubleshooting  
Section 4 Troubleshooting  
Problem  
Cause  
Solution  
Discharge chute plugged Belt not installed correctly  
Check installation of belt  
Grass too wet  
Wait until grass dries  
Grass too tall  
Raise cutting height of mower and cut grass twice  
!
CAUTION  
Do not try to clean discharge opening  
when mower is running. Bodily harm  
may occur.  
RPM of tractor too low  
Mow at full throttle (540 PTO rpm) Check PTO speed &  
tractor engine  
Ground speed too fast  
Shift transmission to a lower gear  
Unplug and clean mower deck  
Remove belt guard shields and clean sheaves  
Replace belt  
Belt slipping Plugged grooming mower  
Debris in sheaves  
Worn belt  
Patches of uncut grass RPM of tractor too low  
Mow at full throttle (540 PTO rpm). Check PTO  
speed & tractor engine  
Ground speed too fast  
Blade damaged or dull  
Shift transmission to a lower gear  
Sharpen & balance or replace blade  
Excessive vibration Power Take Off shaft or distri- Replace Power Take Off or distribution shafts  
bution shafts bend  
Blade broken or bent  
Replace blade  
Sheaves damaged or out of  
alignment  
Replace sheaves or align  
Drive belt damaged  
Replace drive belt  
Inadequate clearance between Remove belt guard shields & clean debris from belt area &  
belt guard shields & belt  
sheaves  
Mower in raised position &  
mower running  
Readjust 3-point hitch to raise mower to maximum of 14  
inches  
Gearbox noisy Low lubricant level  
Check lubricant level  
Blades scalping grass Cutting too low  
Ridges in terrain  
Raise cutting height by adjusting wheels  
Change mowing pattern  
Reduce speed on turns  
Shift to a lower gear  
Fast turning speed  
Uneven cut Ground speed too fast  
Mower not level  
Level mower  
Dull blades  
Sharpen blades & balance or replace  
Mow at full throttle (540 PTO rpm)  
Shift to a lower gear  
Tractor loaded down by mower RPM of engine too low  
Ground speed too fast  
Debris wrapped around  
mower spindles or blades  
Clean mower  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Section 5 Maintenance and Lubrication  
Section 5 Maintenance and Lubrication  
Maintenance  
FD1560 V-BELT INSTALLATION  
Refer to Figure 5-2:  
!
1. Remove belt covers. Loosen spring take-up eyebolt to  
remove belt tension.  
CAUTION  
For Safety reasons, each maintenance operation must be  
performed with the tractor’s PTO disengaged, the mower  
lowered completely, tractor engine shut off and ignition key  
removed.  
2. Move belt take-up handle in a clockwise direction to  
relieve tension on belt.  
3. With tension relieved from belt remove old belt from  
pulleys.  
General Description  
Proper servicing and adjustment is the key to the long life  
of any farm implement. With careful and systematic  
inspection, you can avoid costly maintenance, time and  
repair.  
4. Install new belt referring to the figure below (or refer to  
the decal on top of mower deck). Be sure belt is  
positioned in all the pulley grooves. Tighten belt take-  
up handle spring eyebolt to apply tension to new belt.  
5. Reinstall all belt covers and secure in place with  
hardware.  
General Maintenance  
Blade Sharpening  
1. Blades should be sharpened at each end to the same  
angle as the original cutting edge.  
NOTE: Care should be taken in order not to remove  
any more material than necessary to sharpen blade.  
2. Balance each blade after sharpening.  
Blade Replacement  
IMPORTANT: Always install blade with cutting edge  
facing direction of blade spindle rotation.  
1. Remove cap screw and blade washer from blade to be  
replaced. Remove blade.  
FD1560 V-Belt Installation  
Figure 5-2  
2. Install blade washer into center hole on blade.  
Belt Tension  
3. Replace cap screw. Tighten bolts to proper torque,  
IMPORTANT: Replace blades with Land Pride blades  
only.  
!
CAUTION  
Belt drive system under spring tension; use care to avoid bodily  
harm!  
FD1548 V-BELT INSTALLATION  
1. Belt tension should be checked after approximately 20  
hours of operation on a new belt.  
Refer to Figure 5-1:  
1. Remove right hand, left hand and center belt covers.  
2. Not enough tension on the belt may lead to premature  
failure of the belt due to excessive slipping of the belt.  
2. Using 3/4" socket wrench, pivot over-center latch.  
Rotate idler pulley toward rear of mower.  
Refer to “Belt Tension” page 12 for proper adjustment of  
belt tension.  
3. With tension relieved from belt remove old belt from  
pulleys.  
4. Install new belt referring to the figure below (or refer to  
the decal on top of mower deck). Be sure belt is  
positioned in all the pulley grooves. Reinstall over-  
center latch using socket wrench. Recheck spring  
tension.  
!
WARNING  
Excessive tension on the belt may lead to premature failure of  
belt and drive components. Excessive tension on the belt may  
also lead to a safety hazard to the operator or bystanders.  
5. Reinstall all belt covers and secure in place with  
hardware.  
AIR TIRES (AIR PRESSURE):  
Tire Sealant: Heavy Duty tire sealant has been added in  
Air tires to help reduce air loss from punchers due to  
nails/thorns etc.  
NOTE: Under inflated tires can roll off of rim.  
Maintaining air pressure within 5 PSI of maximum tire  
pressure reduces the risk of tires rolling off of rim.  
FD1548 V-Belt Installation  
Figure 5-1  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Land Pride  
Section 5 Maintenance and Lubrication  
IMPORTANT: Replace blades with genuine Land Pride  
blades only.  
Service Mowing Blades  
1. Both blades should be sharpened at the same angle  
as the original cutting edge and must be replaced or  
reground at the same time to maintain proper balance  
in the mowing unit.  
Storage  
At the end of the working season or when the mower will  
not be used for a long period, it is good practice to clean off  
any dirt or grease that may have accumulated on the  
mower and any of the moving parts.  
NOTE: Care should be taken in order not to remove  
any more material than necessary when sharpening  
blades.  
1. Clean as necessary.  
2. Check the blades for wear and replace if necessary,  
see Service Mowing Blades, this section on page 15.  
2. Both blades should weigh the same after sharpening.  
3. Inspect the mower for loose, damaged or worn parts  
and adjust or replace as needed.  
3. When replacing or sharpening the mower blades,  
examine bolts for excessive wear and replace if  
necessary.  
4. Lubricate as noted in the Lubrication portion of this  
section starting on page 15.  
Blade Replacement  
5. Store unit inside if possible for longer life.  
IMPORTANT: ALWAYS install blade with cutting edge  
facing direction of rotor shaft rotation.  
Repaint parts where paint is worn or scratched to prevent  
rust. Ask your dealer for Aerosol Land Pride Beige touch-  
up paint #821-011C.  
1. Remove the cap screw and the blade washer from the  
blade to be replaced. Remove the blade.  
2. Install the blade washer into the center hole on the  
blade.  
3. Replace cap screw and lock washer and tighten bolts  
to proper torque. See Torque Values Chart for  
Lubrication  
Legend  
Multipurpose  
spray lube  
Multipurpose  
grease lube  
Multipurpose  
oil lube  
Intervals at which  
lubrication is required  
50  
8
PTO U-Joint  
Coat PTO u-joint with grease every 8 hours of operation  
Type of Lubrication: Multipurpose  
Quantity = Coat Generously  
12559  
20  
PTO Shaft  
Disconnect PTO shaft from the tractor and slide apart. Clean  
and coat the inner tube of the PTO shaft with a light film of  
grease and then reassemble.  
Type of Lubrication: Multipurpose  
Quantity = Light Film  
12559  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Land Pride  
Section 5 Maintenance and Lubrication  
8
Wheel Bushing  
Until grease starts to purge.  
Type of Lubrication: Multipurpose grease  
Quantity = Until grease starts to purge  
15040  
Seasonally  
Wheel Support Bushings  
Type of Lubrication: Multipurpose Grease  
Quantity = Until grease starts to purge.  
15040  
25  
Bearing in Blade Spindle Hubs  
Type of Lubrication: Multipurpose Grease  
Quantity = Until grease starts to purge from the top bearing. Top  
bearing has a purge gap which allows grease to purge from it.  
16646  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Land Pride  
Section 5 Maintenance and Lubrication  
DO NOT  
OVERFILL!  
50  
Gearbox  
Check the oil level in the gearbox by removing the plug in the  
top of the box. Add oil if necessary into the biggest plug at  
the back of the box. Retighten both plugs.  
Type of Lubrication: SAE 90 Oil  
16648  
Quantity = Until oil reaches outside plug hole  
IMPORTANT: Should your gearbox require repair, take it to your Land Pride Dealer! Check oil level in gearbox every 50  
hours of operation.  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7/18/08  
17  
Land Pride  
Section 6 Specifications & Capacities  
Section 6 Specifications & Capacities  
FD1548 & FD1560 3-Spindle Grooming Mower  
l
Cutting Width  
Overall Width  
Height  
FD1548  
48"  
FD1560  
60"  
59”  
71”  
36"  
36"  
Length  
44”  
56”  
Weight  
400#  
440#  
Blades - 3  
1/4” x 2 1/2” x 16 3/4”  
Heat Treated  
1/4” x 2 1/2” x 20 3/4”  
Heat Treated  
Alloy Steel  
Alloy Steel  
Blade Tip Speed  
Cutting Height  
15,000 FPM  
15,000 FPM  
1 1/2" - 4 1/2" {1/2" Increments}  
Deck Material Thickness  
Blade Overlap  
10 Gauge  
1 1/2"  
1 1/4"  
Blade Spindles  
Hitch  
Greasable  
Cat. 1 Floating Clevis  
Cat. 1 Floating Clevis  
Gauge Wheels  
Castered 2 3/4" x 8 1/4" Solid Tire  
1" Diameter With Greasable Bushing  
Caster Wheel Spindle  
Drive Train  
540 RPM PTO  
Gearbox  
1:2.83 Ratio  
Beveled Gears  
Cast Iron Housing  
Spring loaded Single V-Belt  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Section 7 Appendix  
Section 7 Appendix  
Torque Values Chart for Common Bolt Sizes  
Bolt Head Identification  
Bolt Head Identification  
5.8  
8.8  
10.9  
Bolt Size  
(Inches)  
in-tpi  
Bolt Size  
(Metric)  
mm x pitch  
Grade 2  
2
Grade 5  
3
Class 5.8  
Class 8.8  
Class 10.9  
Grade 8  
1
4
N · m  
ft-lb  
5.6  
6
N · m  
11  
ft-lb  
8
N · m  
ft-lb  
N · m  
ft-lb  
N · m  
ft-lb  
N · m  
ft-lb  
1/4" - 20  
1/4" - 28  
5/16 - 18  
5/16" - 24  
3/8" - 16  
3/8" - 24  
7/16" - 14  
7/16" - 20  
1/2" - 13  
1/2" - 20  
9/16" - 12  
9/16" - 18  
5/8" - 11  
5/8" - 18  
3/4" - 10  
3/4" - 16  
7/8" - 9  
7.4  
8.5  
16  
18  
12  
M 5 X 0.8  
M 6 X 1  
4
7
3
6
5
9
7
13  
10  
14  
5
11  
8
15  
11  
15  
11  
24  
17  
33  
25  
M 8 X 1.25  
M 8 X 1  
17  
12  
26  
19  
36  
27  
17  
13  
26  
19  
37  
27  
18  
13  
28  
21  
39  
29  
27  
20  
42  
31  
59  
44  
M10 X 1.5  
33  
24  
52  
39  
72  
53  
31  
22  
47  
35  
67  
49  
M10 X 0.75  
M12 X 1.75  
M12 X 1.5  
M12 X 1  
39  
29  
61  
45  
85  
62  
43  
32  
67  
49  
95  
70  
58  
42  
91  
67  
125  
130  
145  
200  
215  
315  
335  
405  
485  
610  
900  
1050  
1150  
2100  
2320  
3660  
4100  
93  
49  
36  
75  
55  
105  
145  
165  
210  
235  
285  
325  
510  
570  
820  
905  
1230  
1350  
1750  
1960  
2460  
2730  
3230  
3680  
4290  
4820  
78  
60  
44  
95  
70  
97  
66  
49  
105  
115  
150  
165  
205  
230  
360  
405  
585  
640  
875  
955  
1080  
1210  
1520  
1680  
1990  
2270  
2640  
2970  
76  
105  
120  
155  
170  
210  
240  
375  
420  
605  
670  
910  
995  
1290  
1440  
1820  
2010  
2380  
2710  
3160  
3560  
90  
66  
105  
145  
155  
225  
240  
310  
350  
440  
650  
760  
830  
1510  
1680  
2650  
2960  
77  
105  
150  
160  
230  
245  
300  
355  
450  
665  
780  
845  
1550  
1710  
2700  
3220  
75  
55  
85  
M14 X 2  
92  
68  
105  
115  
165  
180  
230  
260  
325  
480  
560  
610  
1120  
1240  
1950  
2190  
95  
70  
110  
120  
150  
170  
265  
295  
430  
475  
645  
705  
795  
890  
1120  
1240  
1470  
1670  
1950  
2190  
M14 X 1.5  
M16 X 2  
99  
73  
105  
130  
150  
235  
260  
225  
250  
340  
370  
480  
540  
680  
750  
890  
1010  
1180  
1330  
79  
145  
155  
195  
220  
280  
310  
480  
525  
960  
1060  
1730  
1880  
105  
115  
145  
165  
205  
230  
355  
390  
705  
785  
1270  
1380  
97  
M16 X 1.5  
M18 X 2.5  
M18 X 1.5  
M20 X 2.5  
M20 X 1.5  
M24 X 3  
110  
170  
190  
165  
185  
250  
275  
355  
395  
500  
555  
655  
745  
870  
980  
7/8" - 14  
1" - 8  
M24 X 2  
1" - 12  
M30 X 3.5  
M30 X 2  
1-1/8" - 7  
1 1/8" - 12  
1 1/4" - 7  
1 1/4" - 12  
1 3/8" - 6  
1 3/8" - 12  
1 1/2" - 6  
1 1/2" - 12  
M36 X 3.5  
M36 X 2  
1
2
3
4
in-tpi = nominal thread dia .in inches-threads per inch  
N· m = newton-meters  
ft-lb= foot pounds  
mm x pitch = nominal thread dia. in millimeters x thread pitch  
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.  
Tire Inflation Chart  
Tire Size  
Inflation PSI  
8” x 3” Air Tire  
30  
FD1548 & FD1560 3-Spindle Grooming Mower 310-155M  
7/18/08  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Warranty  
Land Pride warrants to the original purchaser that this Land Pride product will  
be free from defects in material and workmanship for a period of one year, from  
the date of delivery to the end user, when used as intended and under normal  
service and conditions for personal use; and 6 months for municipalities, golf  
courses, sod farms and rental purposes. This Warranty is limited to the  
replacement of any defective part by Land Pride and the installation by the dealer  
of any such replacement part, and does not cover common wear items such as  
blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or  
parts which are claimed to have been defective in material or workmanship.  
This Warranty does not apply to any part or product which in Land Pride’s  
judgment shall have been misused or damaged by accident or lack of normal  
maintenance or care, or which has been repaired or altered in a way which  
adversely affects its performance or reliability, or which has been used for a  
purpose for which the product is not designed. Misuse also specifically includes  
failure to properly maintain oil levels, grease points, and driveline shafts.  
Claims under this Warranty must be made to the dealer which originally sold  
the product and all warranty adjustments must be made through such dealer. Land  
Pride reserves the right to make changes in materials or design of the product at  
any time without notice.  
This Warranty shall not be interpreted to render Land Pride liable for damages  
of any kind, direct, consequential, or contingent to property. Furthermore, Land  
Pride shall not be liable for damages resulting from any cause beyond its  
reasonable control. This Warranty does not extend to loss of crops, any expense  
or loss for labor, supplies, rental machinery or for any other reason.  
No other warranty of any kind whatsoever, express or implied, is made  
with respect to this sale; and all implied warranties of merchantability and  
fitness for a particular purpose which exceed the obligations set forth in this  
written warranty are hereby disclaimed and excluded from this sale.  
This Warranty is not valid unless registered with Land Pride within 30 days from  
the date of delivery to the end user.  
In addition to the Standard Limited Warranty Land Pride also provides:  
A Five - Year Limited Warranty on Gearbox Components, on RC6015,  
RCM6015, RC5015, RCM5015, RC5010, RCM5010, PD15, PD25, and PD35. A  
Three - Year Limited Warranty on Gearbox Components on RCR3596, RCR3510,  
and RCRM3510, provided they have been properly maintained, and not subjected  
to misuse or abuse. Misuse specifically includes, but is not limited to, maintaining  
proper oil levels of the correct lubricant, and adjusting slip-clutches to provide  
proper protection to Gearbox Components. Warranty is One Year for seals. Seals  
are viewed as normal wear items and replacement will be the customer’s  
responsibility. Gearboxes will either be replaced or rebuilt at Land Pride’s  
discretion.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Corporate Office: P.O. Box 5060  
Salina, Kansas 67402-5060 USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KWC Hot Tub 26259072000 User Manual
Land Pride Lawn Mower QH15 User Manual
Lenovo Computer Monitor LT1952p User Manual
Lenovo Laptop 1562 User Manual
Lochinvar Water Heater 151 801 User Manual
Mackie Music Mixer SW0194 92 User Manual
Magic Chef Oven Electric Built In Double Cavity Wall Oven User Manual
Maytag Washer LAT9904 User Manual
McAfee Network Card CERS Port User Manual
Melissa Microwave Oven 253 012 User Manual