Rotary Cutter
SC2660 & SC2672 Skid Steer
24538
326-025M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
© Copyright 2009 Printed
1/07/09
Cover photo may show optional equipment
not supplied with standard unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
L
Land Pride
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved in
the operation, transport, maintenance and storage of
equipment.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
!
L Operator should be familiar with
!
Be Aware of
Signal Words
WARNING
all functions of the unit.
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
L Operate implement from the
driver’s seat only.
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
L Make sure all guards and shields
are in place and secured before
operating the implement.
L Do not leave tractor or implement
!
DANGER
unattended with engine running.
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
CAUTION
L Dismounting from a moving
tractor could cause serious injury
or death.
L Do not allow anyone to stand
between the tractor and
implement while backing up to the
implement.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
L Keep hands, feet, and clothing
away from power-driven parts.
L Wear snug fitting clothing to avoid
entanglement with moving parts.
L Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
L Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
For Your Protection
L Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
Shutdown and Storage
L Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
L Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
L Do not carry passengers on
implement at any time.
OFF
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
1
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
L Use the following maximum
Use Safety
Lights and Devices
Transport
Machinery Safely
speed - tow load weight ratios as
a guideline:
20 mph when weight is less
than or equal to the weight of
tractor.
10 mph when weight is double
the weight of tractor.
L Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.
L Comply with state and local laws.
L Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
L Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
IMPORTANT: Do not tow a load that
is more than double the weight of
tractor.
L Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
L Allow implement to cool
Use A Safety Chain
Practice Safe Maintenance
completely.
L A safety chain will help control
drawn machinery should it
separate from the tractor
drawbar.
L Use a chain with the strength
rating equal to or greater than
the gross weight of the towed
machinery.
L Attach the chain to the tractor
drawbar support or other
specified anchor location. Allow
only enough slack in the chain to
permit turning.
L Understand procedure before
doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
L Do not grease or oil implement
while it is in operation.
L Inspect all parts. Make sure parts
are in good condition & installed
properly.
L Work in a clean dry area.
L Lower the implement to the
ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.
L Remove buildup of grease, oil or
debris.
L Remove all tools and unused
parts from implement before
operation.
L Do not use safety chain for
towing.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
2
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Avoid High
Pressure Fluids Hazard
Wear
Prepare for Emergencies
L Be prepared if a fire starts.
Protective Equipment
L Escaping fluid under pressure can
penetrate the skin causing serious
injury.
L Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
L Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
L Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
L Protective clothing and equipment
L Keep a first aid kit and fire
should be worn.
extinguisher handy.
L Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
L Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
L Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
L Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
L Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
L If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.
911
Keep Riders
Off Machinery
L Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
Tire Safety
Handle
Chemicals Properly
L Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
L When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
L Protective clothing should be
worn.
L Handle all chemicals with care.
L Follow instructions on container
L Never allow children to operate
label.
equipment.
L Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
L Inhaling smoke from any type of
chemical fire is a serious health
hazard.
L When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
L Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
3
Land Pride
Important Safety Information
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Safety Labels
Your Rotary Cutter comes equipped with all safety labels
in place. They were designed to help you safely operate
your implement. Read and follow their directions.
4. Refer to this section for proper label placement.
To install new labels:
a. Clean the area the label is to be placed.
1. Keep all safety labels clean and legible.
2. Replace all damaged or missing labels. To order new
labels go to your nearest Land Pride dealer or visit our
dealer locator at landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
b. Spray soapy water on the surface where the label is to
be placed.
c. Peel backing from label. Press firmly onto the surface.
d. Squeeze out air bubbles with the edge of a credit card.
838-948C
Danger: Do Not Operate
24539
818-556C
Danger: Thrown Objects
24539
818-229C
Amber Reflector
24539
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Important Safety Information
818-830C
Safety Combo
Danger: Keep Hands & Feet Away
Danger: Thrown Object Hazard
Danger: Rotating Blade Hazard
Warning: General Safety
24538
Notice: Read Manual - Observe Safety Messages
818-831C
Warning: High Pressure
24538
818-555C
Danger: Rotating Blade Hazard
24538
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Important Safety Information
24539
818-798C
Warning: Pinch Point Hazard
3-Places
24539
ROTATING DRIVELINE
KEEP AWAY!
25777
818-552C
Danger: Rotating Driveline (SC2672 Only)
25777
818-543C
Danger: Guard Missing (SC2672 Only)
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Introduction
Introduction
A pivoting and adjustable front mounted gauge wheel
with a single laminated tire is available to make mowing
even easier by pre-setting the mowing height and
allowing the cutter to float over uneven terrain. Hydraulic
hoses and a case-drain line are provided as standard
equipment but compatible couplers for attachment to the
individual skid steers auxiliary hydraulic outlets will need
to be provided by dealers or customers.
Land Pride welcomes you to the growing family of new
product owners.
This Rotary Cutter has been designed with care and built
by skilled workers using quality materials. Proper
assembly, maintenance and safe operating practices will
help you get years of satisfactory use from the machine.
Application
The addition of a Land Pride SC2660 or SC2672 Skid
Steer Rotary Cutter to your arsenal of skid steer
attachments will dramatically increase the versatility and
value of your personal skid steer investment.
The SC2660 and SC2672 Series Skid Steer Rotary
Cutters are built and designed by Land Pride for cutting
on gently sloping or slightly contoured right-of-ways,
pastures, set aside acres, and row crop fields. These
skid steer mounted cutters provide unparalleled access
to tightly restricted areas such as under fences, in and
around boxed in corner sections of corrals and out
buildings, vineyard and nursery rows, wooded lots, and
approaches to ditches and waterways. The 60" or 72"
cutting width, 8"offset capability to the right, 2" cutting
capacity, 1.5" to 18" cutting height range, and the
universal skid steer floating-hitch mounting plate make
the SC2660 and SC2672 highly versatile and easy to
use. The SC2660 is compatible with and designed for
attachment to skid steers having 1500 psi to 3000 psi
operating pressure and flow rates in the 11-15 gpm,
15-21 gpm, or 18-27 gpm ranges. The SC2672 is
compatible with and designed for attachment to skid
steers having 1500 psi to 3000 psi operating pressure
and flow rates in the 15-21 gpm, or 18-27 gpm ranges.
for additional information and performance enhancing
options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
The SC2660 and SC2672 provide very high and clean
cutting blade tip speeds but owner/operators will need to
select the motor that is appropriately matched to their
skid steers hydraulic flow and pressure capabilities. Our
low volume motor, which is available on the SC2660
only, produces a blade tip speed of 18,540 fpm at
15 gpm. Medium volume and high volume motors are
available for both models. On the SC2660, our medium
volume motor produces 18,850 fpm at 21 gpm, and our
high volume motor produces 19,000 fpm at 27 gpm. On
the SC2672, our medium volume motor produces
17,200 fpm at 21 gpm, and our high volume motor
produces 18,550 fpm at 27 gpm. Each unit is equipped
with two 1/2" x 4"updraft blades and a heavy duty round
pan stump jumper. A deflector chute is located to the left
rear side of the cutter to prevent clogging in heavy cutting
conditions.
• Store your Operator’s manual in the dry storage tube for
future reference. See Figure 1 on page 8 for location of
storage tube.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
NOTE: A special point of information that the
operator must be aware of before continuing.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
The SC2660 and SC2672 come standard with a front
mounted single row chain guard, a rear mounted double
row chain guard, and a safety chain to restrict deck lift
height. Four corner-mounted skid shoes are provided to
reduce wear and to keep the cutter from bottoming out. A
Lexan protective cab door is available as optional
equipment or owner/operators may choose to use a
protective door provided or made available by their skid
steer supplier/manufacturer.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Introduction
Further Assistance
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
Your dealer wants you to be satisfied with your new
Rotary Cutter. If for any reason you do not understand
any part of this manual or are not satisfied with the
service received, the following actions are suggested:
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Rotary
Cutter.
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
The parts on your Rotary Cutter have been specially
designed and should only be replaced with genuine Land
Pride parts. Therefore, should your cutter require
replacement parts go to your Land Pride Dealer.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the problem
and request assistance.
3. For further assistance write to:
Serial Number Plate
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure to include your serial and model numbers
in correspondence also. Refer to Figure 1 for the location
of your serial number plate.
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
24544
Manual
Storage
Tube
Serial Number Plate Location
Figure 1
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Read and understand the operator’s manual for your
cutter. An understanding of how it works will aid in the
assembly and setup of your cutter.
Skid Steer Requirements
The Rotary Cutter is designed to attach to Skid Steer
Loaders with the following minimum requirements:
This Rotary Cutter has been partially assembled at the
factory. However, some assembly will be necessary.
SAE Lift Capacity
SAE Lift Capacity . . . . . . . . . . . . . . . . . . . . .1200 lbs.
It is best to go through the Pre-Assembly Checklist
before assembling the cutter. Speed up your assembly
task and make the job safer by having all the needed
parts and equipment readily at hand.
Operating Hydraulic Pressure
Hydraulic Pressure Rating . . . . . . .1,500 - 3,000 PSI.
Hydraulic Flow Rate
Low Volume Motor & Hoses . . . . . . . . . 11 - 16 GPM.
Ensure that the intended Skid Steer conforms to the
requirements stated under the heading “Skid Steer
Medium Volume Motor & Hoses . . . . . . 17 - 21 GPM.
High Volume Motor & Hoses. . . . . . . . . 22 - 27 GPM.
Hydraulic Connections
Hydraulic Hoses . . . . . . . . . . . . . 2 - Hydraulic Outlets
Case Drain Hose . . . . . . . . . . . . .1 - Hydraulic Outlet
Uncrating
IMPORTANT: Skid Steer must be equipped with a
case drain system.
!
DANGER
Do not remove cutter from crate until after it has been securely
supported with an overhead crane, fork lift or other suitable
equipment. Cutter can fall and injury someone if crating
hardware is removed before properly supporting the deck.
Protective Equipment
The Skid Steer MUST be equipped with a protective
door shield. A universal operator protective door shield
for additional information and installation.
1. Secure deck with an overhead crane, fork lift or other
suitable means before cutting shipping support
bands and unbolting cutter from shipping crate.
IMPORTANT: Ballast may need to be added to your
Skid Steer to maintain steering control and to
prevent tipping of the Skid Steer. Refer to your Skid
Steer’s operator manual to determine if additional
ballast is needed.
2. Cut bands securing parts bags to the shipping crate.
3. Remove bolts securing hitch to the shipping crate.
4. Cut center band securing hitch to shipping crate.
5. Carefully lower cutter onto its skids or onto support
stands capable of supporting the cutter.
Dealer Preparations
6. Remove wood from under the front chain guard.
Pre-Assembly Checklist
Float Chain Assembly
All hardware from the factory has been installed. If a
part or fastener is temporarily removed for assembly
reasons, remember where it goes. Keep parts
separated.
Refer to Figure 1-1:
1. (Not Shown) Unbolt and remove shipping brace bars
extending from hitch plate to center of deck.
2. Attach clevis end (#1) of float chains (#4) to hitch plate
with 9/16" clevis pins (#2) and cotter pins (#3). Bend
cotter pin legs to keep them from falling out.
Be sure the parts get used in the correct location. By
double checking while you assemble, you will lessen
the chance of using a bolt incorrectly that may be
needed later. Use Parts Manual to identify location of
parts you are unsure of where they are used.
3. Install other end of float chains (#4) to deck with
1/2" clevis pins (#5) and 1/8" cotter pins (#6). Bend
cotter pin legs to keep them from falling out.
All grease fittings are in place and lubricated.
Miscellaneous assembly tools: hammer, tape measure,
assortment of wrenches and spirit level.
Have fork lift or loader along with chains and safety
stands sized for the job ready for the assembly task.
Auxiliary weights (depending on Skid Steer size).
Have a minimum of 2 people at hand while assembling.
Safety decals are legible and undamaged.
Loose parts bag/box shipped with the Rotary Cutter.
Figure 1-1
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Refer to Figure 1-3:
SC2660 Motor And Hose Assembly
1. Remove fasteners (#9 & #10) and coupling
Your Skid Steer Rotary Cutter is factory supplied with
one of three motors mounted to the deck. Make sure you
check GPM rating on the hydraulic motor decal to verify
if it matches your Skid Steer’s GPM rating. Skip
assembly instructions below if the motor GPM rating
matches your Skid Steer.
guard (#8). Keep fasteners and coupling guard for
reassembly of new motor.
1. Remove fasteners (#1, 2, 3 & 4). Keep fasteners for
reassembly of new motor.
2. Remove existing motor and hose assembly (#5). Clean
old gasket material (#6) from mounting flange (#7).
select a motor that matches your Skid Steer.
3. Place new gasket (#6) onto mounting flange (#7).
Refer to Figure 1-2:
4. Gently slide new motor and hose assembly (#5) onto
coupling (#12) with hoses extending towards the hitch
plate.
1. Remove fasteners (#1, 2, 3 & 4). Keep fasteners for
reassembly of new motor.
2. Remove existing motor and hose assembly (#5). Clean
old gasket material (#6) from gearbox flange (#7).
5. Secure hydraulic motor assembly with the four existing
1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#1), flat
washers (#4), lock washers (#3) and 1/2"-13 hex huts
3. Place new gasket (#6) onto gearbox flange (#7).
4. Gently lower new motor and hose assembly (#5) onto
gasket (#6) with hoses extending towards the hitch
plate.
6. Reattach coupling guard (#8) with 5/16" spring lock
washers (#10) and 5/16"-18 x 3/4" GR5 hex head cap
screws (#9). Tighten nuts to correct torque.
5. Secure hydraulic motor assembly with the four existing
1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#1), flat
washers (#4), lock washers (#3) and 1/2"-13 hex huts
Decal Location
Stating Motor
GPM Rating
Decal Location Stating
Motor GPM Rating
25732
SC2672 Motor and hose Assembly
Figure 1-3
SC2672 Vent Plug With Dipstick
IMPORTANT: Ref. Figure 1-4. A solid plug is
24545
shipped with the gearbox to prevent loss of oil during
shipping and handling. Before operating the cutter,
this plug must be replaced with the vent plug and
dipstick included with this manual.
SC2660 Motor and hose Assembly
Figure 1-2
SC2672 Motor And Hose Assembly
Your Skid Steer Rotary Cutter is factory supplied with
one of three motors mounted to the deck. Make sure you
check GPM rating on the hydraulic motor decal to verify
if it matches your Skid Steer’s GPM rating. Skip
assembly instructions below if the motor GPM rating
matches your Skid Steer.
Vented Plug
With Dipstick
Oil Level
Plug
DO NOT
OVERFILL
select a motor that matches your Skid Steer.
20822
Figure 1-4
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Hitch Hook-Up
Refer to Figure 1-5:
Hydraulic Hose Hook-up
Refer to Figure 1-5:
Two high pressure hydraulic outlets are required for the
hydraulic motor hoses and one outlet for the case drain
hose.
!
CAUTION
Do not stand between Skid Steer loader and implement during
hookup.
!
1. Make sure hydraulic hoses and height adjustment
safety chain do not interfere with hitch hook-up.
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be treated by a
doctor within a few hours or gangrene may result.
2. Drive Skid Steer slowly to the Rotary Cutter making
sure the front hitch plate of the Skid Steer is parallel
with the Rotary Cutter hitch.
3. Tilt top of Skid Steer hitch plate slightly forward.
4. Place top of Skid Steer hitch plate under the Rotary
Cutter top angle bar.
1. Remove plastic cap from case drain hose and attach
hydraulic coupler (supplied by customer) to the hose.
5. Slowly lift Skid Steer’s hitch until Rotary Cutter’s hitch
and Skid Steer’s top angle bar have come together.
2. Connect case drain hose to reservoir outlet.
3. Connect male and female couplers on the hydraulic
motor hoses to the Skid Steer high pressure outlets.
6. Push lock handles of the Skid Steer down so that the
pins go through the bottom slots of the Rotary Cutter’s
hitch and the handles lock down.
4. Operate skid steer to check blade rotation. Cutter
blades should rotate clockwise when looking at the
blades from above. If cutter blades are rotating
counterclockwise, switch male and female couplers
and reconnect to skid steer outlets.
7. Loop height adjustment safety chain forward down and
under 2" x 3" tube and then attach to Skid Steer’s lower
hitch loop. See “Height Adjustment Safety Chain” on
Case Drain Line
Clockwise
Blade Rotation
Male Coupler
Top Angle Bar
Bottom Slots
Female Coupler
Height Adjustment Safety Chain
(Attach to Skid Steer’s lower hitch loop.)
Rear Skid Shoe
24538
Skid Steer Hook--Up
Figure 1-5
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
11
Land Pride
Section 1: Assembly & Set-up
Gauge Wheel Assembly (Optional)
Required Tools:
• 1 ea. - Small hammer
• 2 ea. - 1/2" drift punches or alignment tools
• 2 ea. - 9/16" box end wrench
• 2 ea. - 3/4" box end wrench
• 1 ea. - Torque wrench with 9/16" and 3/4" sockets
Assembly Instructions:
Refer to Figure 1-6:
.
3. Check alignment of gauge wheel front mount holes with
chain guard holes. Skip to step 4 if mounting holes are
in alignment. If gauge wheel mounting holes are not in
alignment, loosen remaining chain guard bolts and
realign chain guard as follows.
IMPORTANT: Do not enlarging any of the 5 bolt
holes used for mounting the gauge wheel. Enlarging
bolt holes can severely decrease the longevity of
your gauge wheel operation.
1. Remove four 3/8"-16 x 3" lg. GR5 hex head bolts (#2)
in the center of the front chain guard. Keep bolts,
washers and whiz nuts for reassembly of gauge
wheel arm (#1).
a. Realign chain guard by inserting drift punches in
the outer two gauge wheel mounting holes. Tap
punches in with a hammer until secure. Do not
remove punches at this time.
2. Install gauge wheel deck mount (#1) by inserting
1/2" x 3 3/4" lg. GR8 bolt (#3) through 1/2" flat
washer (#8), gauge wheel mounting bracket (#1) and
deck tube. Secure bolt with 1/2" flat washer (#8), lock
washer (#7) and hex nut (#4). Do not torque nut at this
time. Finger tighten nut only.
b. Insert 3/8"-16 x 3" lg. GR5 bolts (#2) with 3/8" flat
washers (#6) through the two inside holes.
Secure bolts with 3/8" whiz nuts (#5). Tighten
bolts to 31 ft-lbs.
c. Remove left hand drift punch and install
3/8" x 3" lg. GR5 hex bolt (#2), flat washer (#6)
and whiz nut (#5). Tighten 3/8" bolt to 31 ft-lbs.
d. Remove right hand drift punch and install
3/8" x 3" lg. GR5 hex bolt (#2), flat washer (#6)
and whiz nut (#5). Tighten 3/8" bolt to 31 ft-lbs.
e. Tighten remaining chain guard bolts to 31 ft-lbs.
4. If gauge wheel mounting holes are in alignment, Install
four 3/8" x 3" lg. GR5 hex bolts (#2), flat washers (#6)
and whiz nuts (#5). Tighten 3/8" bolts to 31 ft-lbs.
5. Tighten 1/2" gauge wheel top bolt (#3) to 76 ft-lbs.
6. Attach heavy duty ratchet jack (#14) to cutter frame
and to gauge wheel deck mount (#1) with 1" x 3 3/16" lg
clevis pins (#11). Secure with hair pin cotters (#10).
7. Insert four 1 1/2" I.D. machine washers (#9) over gauge
wheel spindle (#13).
8. Insert gauge wheel spindle (#13) through yoke in
gauge wheel deck mount (#1) and 1 1/2" I.D. machine
washer (#9). Secure gauge wheel with 3/8" x 2 1/2" lg.
roll pin (#12).
24547
Gauge Wheel Assembly
Figure 1-6
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Skid Shoe Assembly (Optional)
Refer to Figure 1-7:
Cutters ordered with skid shoes are shipped loose.
Install skid shoes as follows:
1. Raise the Rotary Cutter 3" or more off the ground
and place support blocks under the cutter. Make sure
support blocks are positioned so they will not
interfere with skid shoe installation.
2. Lower cutter onto support blocks, place Skid Steer in
park, set park brakes, shut Skid Steer off and remove
switch key.
3. Install short skid shoe (#2) to the back left deck corner
as shown with 3/8”-16 x 1 1/4 GR5 plow bolts (#2), flat
washers (#6), lock washers (#5) and 3/8" lock nuts
(#4). Torque lock nuts (#4) to 31 ft-lbs.
4. Install long skid shoes (#1) to the remaining three deck
corners with 3/8”-16X1 1/4 GR5 plow bolts (#2), flat
washers (#6), lock washers (#5) and 3/8" lock nuts (#4).
Torque lock nuts (#4) to 31 ft. lbs.
5. Raise cutter up and remove support blocks.
24546
Skid Shoe Replacement
Figure 1-7
Operator Protective Door (Optional)
Refer to Figure 1-8:
If needed, Locate & Cut
Notches in Door For
U-bolts Clearance.
!
WARNING
Do not drill holes in the ROPS (Roll Over Protection System)
to attach this Operator Protective Door. Drilling unapproved
holes in the ROPS can weaken the structure and void its
warranty.
Hook Elastic Tie-Down
To Skid Steer Cage To
Keep Door Closed.
1. Cut notches in protective door as needed to provide
clearance around u-bolts and Skid Steer frame.
2. Install Operator Protective Door to the Skid Steer’s
hand hold with two u-bolts (#3), flat bars (#2) and four
nuts (#1) as shown. Tighten nuts to correct torque.
If Needed, Locate
& Cut Notch in
Door To Clear Skid
Steer Frame.
Skid Steer
Hand Hold
24608
Operator Protective Door
Figure 1-8
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
13
Section 2: Adjustments
Section 2: Adjustments
Hitch Positioning
Refer to Figure 2-1:
Hitch Mounted Centered
1. Align hitch pivot pin bushings (#3) with cutter
mounting lug holes (A2).
The Rotary Cutter hitch is designed to be centered on the
cutter or offset to position the cutter to the right.
Offsetting the cutter to the right will allow the unit to cut
close to obstacles.
2. Insert hitch pivot pins (#7) through mounting lug holes
(A2) and bushings (#3).
3. Secure pivot pins by driving roll pins (#6) through pivot
pin holes.
Hitch Mounted Offset
1. Align hitch pivot pin bushings (#3) with cutter
mounting lug holes (A1).
4. Attach Floating Chains (#4) to hitch plate lugs at
position (B2) with chain pins (#5).
5. Insert cotter pins (#2) through chain pin holes and bend
one leg of each cotter pin to secure it in place.
2. Insert hitch pivot pins (#7) through mounting lug holes
(A1) and hitch bushings (#3).
3. Secure pivot pins by driving roll pins (#6) through pivot
pin holes.
4. Attach Floating Chains (#4) to hitch plate lugs at
positions marked (B1) with chain pins (#5).
5. Insert cotter pins (#2) through chain pin holes and bend
one leg of each cotter pin to secure it in place.
24548
Hitch Offset
Figure 2-1
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
14
Land Pride
Section 2: Adjustments
Refer to Figure 2-2:
Height Adjustment Safety Chain
For safety, the cutter rear skid shoes should not be
raised higher than 16 1/2" off the ground (18" Maximum
cutting height).
!
WARNING
Always secure cutter deck in the up position with solid
supports or by locking the hydraulics before working around
or under a raised deck. Never work under equipment
supported by hydraulics. Hydraulics can drop equipment if
controls are actuated or if hydraulic lines burst. Either
situation can drop the cutter instantly even when power to the
hydraulics is shut off.
NOTE: Two people may be required to install and
adjust the safety chain.
1. Raise cutter’s rear skid shoes slightly less than
16 1/2" off the ground.
2. Run height adjustment safety chain from under the
2" x 3" hitch tube to the Skid Steer lower hitch loop.
Thread chain through the hitch loop and back towards
the hitch plate. Connect quick link coupler to a chain
loop as shown.
!
DANGER
Do not raise cutter higher than 16 1/2" off the ground. Raising
cutter higher can cause serious bodily injury and/or death.
Use safety limit chain to limit cutter height.
3. Raise cutter up until the safety chain is tight. Check
height of rear skid shoes.
4. If rear skid shoes are higher than 16 1/2" above ground
level, lower cutter and make necessary adjustments to
the safety chain to limit rear skid shoe height to
16 1/2" maximum.
!
DANGER
Do not tilt hitch plate to raise front of cutter higher than the
rear. Raising front of cutter can cause serious bodily injury
and/or death.
5. Tighten quick link coupler nut to secure safety chain.
Ratchet Jack
Cutter Hitch Plate
Quick Link Coupler
Height Adjustment
Safety Chain
Bottom of Rear
Skid Shoes
16 1/2"
Maximum Lift
Gauge Wheel
Ground Level
Skid Steer
Lower Hitch Loop
24586
Nominal Cutting Height
Figure 2-2
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 2: Adjustments
Deck Leveling with
Optional Gauge Wheel
Refer to Figure 2-3:
1. Park Skid Steer with cutter on a level surface.
2. Adjust ratchet jack to raise gauge wheel up until it is
even with bottom of front skid shoes.
3. Use Skid Steer hydraulics to lower Skid Steer lift arms
and to tilt cutter hitch plate angle until bottom of skid
shoe at the front deck corner is dimension (A) off the
ground and the rear deck corner is slightly higher off the
ground than the front deck corner.
!
DANGER
Engage parking brake, disengage power to cutter, shut off
Skid Steer, remove key and ensure that all moving parts have
come to a complete stop before dismounting from the Skid
Steer.
4. Adjust ratchet jack to lower gauge wheel until it is at
ground level.
IMPORTANT: The blades should be positioned to cut
material only at the front of the cutter. If the deck is
level or the rear of the cutter is lower than the front,
then the blades are subject to continuous material
flow resulting in cutting clumps at the discharge chute,
horsepower loss, high blade wear, and frequent blade
sharpening.
5. With gauge wheel at ground level, use Skid Steer
hydraulics to adjust cutter hitch plate angle until the
float chain sags.
!
CAUTION
Do Not over angle hitch plate forward. Over angling can
cause damage to deck, hitch and gauge wheel.
NOTE: Nominal Cutting Height is the distance
from bottom of cutter blade to ground level at the
front of the cutter. Subtract 1 1/2" from Nominal
Cutting Height to determine distance (A). Distance
(A) is measured from bottom of front skid shoes to
ground level.
The Rotary Cutter should be operated with gauge wheel
on the ground, slack in float chain and deck rear slightly
higher off the ground than deck front. As the operator
travels over uneven terrain, the Skid Steer hitch plate tilt
angle and lift arm height may need some readjusting to
maintain correct deck positioning.
Float Chain should sag when gauge wheel is
resting on level ground. Adjust hitch plate
tilt angle to put a sag in the Float Chain.
Cutter Hitch Plate
Ratchet Jack
Gauge Wheel
Height Adjustment
Safety Chain
A"
Ground Level
The rear deck corner should be raised
slightly higher above ground level
than the front deck corner.
A" is 1 1/2" less than Nominal Cutting Height
and is the distance from bottom of Skid Shoe
at the front deck corner to ground level.
Nominal Cutting Height is the
distance from bottom of the
front leading cutting blade to
ground level.
24585
Nominal Cutting Height
Figure 2-3
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
16
Land Pride
Section 2: Adjustments
Deck Leveling without
Optional Gauge Wheel
Refer to Figure 2-4:
1. Park Skid Steer with cutter on a level surface.
2. Use Skid Steer hydraulics to lower Skid Steer lift arms
and to tilt cutter hitch plate angle until bottom of skid
shoe at the front deck corner is dimension (A) off the
ground and the rear deck corner is slightly higher than
the front deck corner.
!
DANGER
Engage parking brake, disengage power to the cutter, shut off
Skid Steer, remove key and ensure that all moving parts have
come to a complete stop before dismounting from the Skid
Steer.
The Rotary Cutter should be operated with float chain
tight to hold the front of the cutter at the correct cutting
height and lift arms set to hold the rear of the cutter
slightly higher off the ground than the front. As the
operator travels over uneven terrain, the Skid Steer hitch
plate tilt angle and lift arm height will need readjusting
often to maintain correct deck positioning.
IMPORTANT: The blades should be positioned to cut
material only at the front of the cutter. If the deck is
level or the rear of the cutter is lower than the front,
then the blades are subject to continuous material
flow resulting in cutting clumps at the discharge chute,
horsepower loss, high blade wear, and frequent blade
sharpening.
NOTE: Nominal Cutting Height is the distance
from bottom of cutter blade to ground level at the
front of the cutter. Subtract 1 1/2" from Nominal
Cutting Height to determine distance (A). Distance
(A) is measured from bottom of front skid shoes to
ground level.
Float Chain is kept tight
Cutter Hitch Plate
Height Adjustment
Safety Chain
A"
Ground Level
A" is 1 1/2" less than Nominal Cutting Height
and is the distance from bottom of Skid Shoe
at the front deck corner to ground level.
The rear deck corner should be raised
slightly higher above ground level
than the front deck corner.
Nominal Cutting Height is the
distance from bottom of the
front leading cutting blade to
ground level.
24591
Nominal Cutting Height
Figure 2-4
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
17
Section 3: Operating Procedures
Section 3: Operating Procedures
Operating Information
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport,
maintenance and storage of the Rotary Cutter.
Therefore, it is absolutely essential that no one operates
the Rotary Cutter without first having read, fully
understood and become totally familiar with the
Operator’s Manual. Make sure the operator has paid
particular attention to:
!
WARNING
Do not operate Rotary Cutter without an operator protective
door mounted to the cab and protective eye wear such as
safety glasses or goggles. Flying objects from the cutter can
cause serious injury to the body and eyes.
!
WARNING
The SC2660 Rotary Cutter is designed to cut grass and brush
up to 2” in diameter. Using this cutter for another type of work
can damage the drive components, deck and support frame.
!
WARNING
Do not travel too fast. The rougher the terrain, the slower you
must travel. Always travel at a speed slow enough to be able
to adjust the deck height before running it into the ground.
Remember, sudden dropping of the front tires can slam the
deck into the ground. Also, travel slow enough to stop before
running or turning into obstacles ahead and on either side.
The following inspections should be performed before
operating your Skid Steer cutter.
Inspection Checklist
L Check
Reference
!
DANGER
Make Sure all guards and shields are in place
and secure.
Do not cut on steep inclines. The Skid Steer could flip over
causing damage to the equipment, serious injury or death.
Inspect Hydraulic hoses for wear, damage
and hydraulic leaks. Replace damaged and
worn hoses with genuine Land Pride parts.
!
DANGER
Do not use deck to lift, push or pull objects. This can damage
the deck, cause serious injury or death.
Grease all fittings. Refer to “Lubrication”
for loose bolts & pins, Torque Values Chart.
!
DANGER
Never carry a person on the cutter. A person can fall and be
ran over causing serious injury or death.
!
CAUTION
Rotary Cutters have the ability to discharge objects at high
speeds. Therefore, the use of front & rear deck safety shields
is required! Keep all bystanders at least 100 yards away.
Flying objects from the cutter can cause serious injury or
death.
!
DANGER
Do not use deck as a working platform. The deck is not
properly designed or guarded for this use. Using deck as a
working platform can cause serious injury or death.
!
CAUTION
Do not cut after dark without working lights. The equipment
can be damaged from hitting objects not seen in the dark and
from being hit by vehicles not able to see the equipment.
!
DANGER
Do not use deck as a fan. Cutting blades are not properly
designed or guarded for this use. Using the deck as a fan can
cause serious injury or death.
!
CAUTION
Cutter deck can be slippery especially when wet. Always step
on the anti grip pads when possible. Never hurry. Make sure
you have secure footing and hand hold when walking on the
deck.
!
DANGER
Do not operator the cutter with cutting blades raised higher
than 18" off the ground. Always use the height adjusting safety
chain to limit cutting height to 18" (16 1/2" skid shoe height).
Raising the cutter higher can throw debris at the operator and
cause serious injury or death.
!
WARNING
Do not become entangled in the hydraulic hoses. Tripping
over the hoses while entering or exiting the Skid Steer
operator station can cause serious injury to the body.
!
DANGER
Shields must be secured in place when operating to avoid
injury or death from entanglement in rotating drivelines.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 3: Operating Procedures
3. If included, adjust gauge wheel to support deck front at
the preferred height and tilt hitch plate to put slack in the
float chains.
!
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be treated by a
doctor within a few hours or gangrene may result.
4. Start the machine and engage hydraulic motor. Allow
several seconds for cutter blades to become aligned
properly. If deck continues to vibrate after several
seconds, stop motor and inspect blades.
5. It is important to maintain correct hydraulic motor
speed. Loss of motor speed will allow the blades to
hinge back and result in ragged, uneven cutting.
IMPORTANT: Shut off all power, disengage
auxiliary hydraulics, set park brake and remove
ignition key any time the Rotary Cutter is not
operating properly or needs adjustment.
6. Ground speed depends on two things: the density of
the material being cut and size of Skid Steer. Never run
fast enough to overload the Skid Steer and/or cutter.
7. This cutter was designed to cut grass and medium
brush cutting on gently sloping or slightly contoured
right-of-ways, pastures, set aside acres, and row
crop fields.
IMPORTANT: Avoid catching the hydraulic hoses on
brush, post, stumps, and other protrusions that
could damage and/or break them.
Transporting
!
CAUTION
When traveling on public roads whether at night or during the
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
1. Be sure to reduce ground speed when turning; and,
leave enough clearance so the Rotary Cutter does
not contact obstacles such as buildings, trees or
fences.
DO NOT OPERATE WITH
SKID STEER FRONT WHEELS OFF THE GROUND
Figure 3-1
2. Select a safe ground travel speed that is 20 m.p.h. or
less when transporting from one area to another. When
traveling on roadways, transport in such a way that
faster moving vehicles may pass you safely.
3. Decrease transport speed when traveling over rough or
hilly terrain.
!
WARNING
DO NOT OPERATE CUTTER OR NAVIGATE TURNS WITH
FRONT WHEELS OF SKID STEER OFF THE GROUND.
OPERATING IN ABOVE FASHION WILL CAUSE DAMAGE
TO DECK, HITCH AND GAUGE WHEEL.
4. When transporting Skid Steer and Rotary Cutter on a
trailer:
• Use towing vehicle and trailer of adequate
capacity.
• Always drive up a ramp with heavy end uphill.
General Operating Instructions
• Engage Skid Steer park brake and remove ignition
It is absolutely essential that you read and understand
both the operator’s manual for the Land Pride SC2660 or
SC2672 Skid Steer Rotary Cutter and the operator’s
manual for the Skid Steer unit you intend to attach it to
before attempting to operate or cut with this combination
of equipment. You must be able to read, comprehend
and adhere to all safety warnings and decals in order to
avoid personal injury, fatalities, injury to others, or costly
damage to property and equipment. We highly
switch key once it is loaded.
• Secure Skid Steer Loader and attachment using
tie-downs and chains.
Cutting Instructions
NOTE: Your cutter is equipped with free swinging
cutting blades to reduce shock loads to the cutter
when striking an obstacle.
recommend that you be a skilled and competent Skid
Steer operator prior to attaching and attempting to use
the SC2660 or SC2672 Skid Steer Rotary Cutter. If there
is any part of the information above or safe operating
procedures you do not understand, please contact your
nearest authorized dealer for a full explanation and
training session if necessary.
1. Thoroughly inspect the area to be cut for debris and
unforeseen objects. Mark any potential hazards.
2. Set Skid Steer hydraulic lift arms and hitch angle to
position the deck front at the preferred cutting height
and the deck rear slightly higher.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 3: Operating Procedures
accomplished and the mower is fully supported by the
Skid Steer lift arms, lower the mower to a point
Skid Steer Operating Instructions
Assuming you have met all of the above requirements
and taken them seriously, it is time to take the next step
and that is accomplished by dressing appropriately for
the task. You will need to put on protective eye wear such
as safety glasses, goggles, or a face shield. A hard hat,
steel toed safety shoes, gloves, and hearing protection
are also highly recommended. Never wear loose fitting
clothing and you may want to put on a respirator or filter
mask to avoid breathing in dust, pollen, or agriculturally
used toxins that may be present.
approximately two inches above the ground. Turn the
engine off, set the parking brake, and climb out of the Skid
Steer. Lock the latch handles down to engage the hitch
pins. Make the appropriate hydraulic connections to the
auxiliary hydraulic outlet and case drain making sure to
keep connectors clean. Be sure to use proper fittings and
if connection is difficult, moving levers may help relieve
line pressure. (Note! Hydraulic flow direction on all skid
steers is not the same. Make sure hoses are connected
properly or blades will rotate at a much slower speed.)
Wipe away spilled or excess hydraulic oil and secure
Cordura sleeves to contain potential leaks. Connect the
height limiting safety chain to the chassis attaching point
and restrict cutting height to no more that eighteen
inches. This completes the attachment of the cutter to the
Skid Steer.
The next step is a static or non-running pre-inspection of
the Skid Steer unit. You will want to make sure that the
Skid Steer is equipped with a fully functioning ROPS
(Roll Over Protection System) which does include seat
belts and an operator safety enclosure. The cab must
also be equipped with an operator protective door, which
may have been supplied with the Skid Steer unit. Land
Pride does offer a protective door with the SC2660 and
SC2672 if one is not already provided. If the Skid Steer is
to be operated on local roadways, it must be equipped
with appropriate Slow Moving Vehicle (SMV) and other
required lighting packages so as to make it compliant
with state and local department of transportation
requirements. The cutter drive motor must be matched to
the output of the hydraulic capacity of the Skid Steer.
Failure to do this could result in serious over-speeding of
the cutting unit possibly resulting in serious injury,
fatalities or property damage. The universal quick-hitch
mount should be in good working order and latches
should be located to the open position. There should be
no evidence of hydraulic leaks in and around the
auxiliary hydraulic couplers. There must be a readily
accessible attaching point for the Rotary Cutter lift-limit
chain on the lower front portion of the chassis frame.
Finally make sure that all shields and safety features are
in place and fully functional.
The next step is to complete a pre-operation check of the
cutter. Make sure all guards, safety shields, safety
chains, and deflectors are in place. All hardware must be
in place and appropriately tightened. Damaged, severely
worn or defective parts must be replaced prior to
operation. If your unit is equipped with the optional front
mounted gauge wheel, you will want to adjust it for
desired cutting height at this time.
You should always inspect the area where you intend to
cut for debris and hazards located on the ground. No one,
including people and animals, should be allowed within
100 yards of this cutter when in operation. If someone
does approach, shut the cutter down immediately. The
blades on this cutter should never be allowed to come in
contact with objects such as wire, cable, rope, or chains
that might become entangled. These types of entangled
objects can become extremely hazardous by rotating
outside of the cutter deck housing resulting in serious
injury or death. Always inspect the area before you mow.
The next step is to perform a running check of the Skid
Steer unit. As you get onto the Skid Steer and into the
operator’ compartment always use factory provided
hand-holds and don’t grab the steering or control levers
to ease or stabilize your entry. Fasten your seat belt once
you are seated and begin to mentally orient yourself with
the position of all controls, switches, pedals, levers, and
their related functions. Once you are sure that the park
brake is on, no people or animals are in close proximity,
all control levers, pedals and hydraulic systems are in
neutral position, go ahead and start the engine. With the
engine now running and the throttle at approximately one
third, test all controls to make sure they are fully
The best mowing results will be achieved at speeds
between 2 mph and 5 mph as grounds and mowing
conditions dictate. If you are mowing in particularly tall or
dense brush, you may want to make two passes with the
first pass being at 18" and the second pass made as a
cross-cut at the desired cut height. If you are mowing
without the benefit of the front mounted gauge wheel in
the float position, you will probably need to slow down
significantly especially over uneven terrain or furrows.
Driving too fast over uneven ground will cause the unit to
undulate in a forward pitching motion. The best advice is
to drive slow but keep engine speed and blade tip speed
high. Once you get the feel of it you can increase speed
and productivity.
functioning. If at any time there is an equipment failure,
shut the unit down and make immediate and full repairs.
When you do need to stop, make sure you set the park
brake, shut the Skid Steer engine off, and allow time for
the blades to stop rotating before you climb down. With a
little practice we are confident you will soon achieve safe
and excellent results with your new Land Pride SC2660 or
SC2672 Skid Steer Rotary Cutter.
Rotary Cutter Operating Instructions
Assuming all systems with the Skid Steer are “go” and
fully functioning, it is time to connect to the SC2660 or
SC2672 Rotary Cutter. This is done by maneuvering the
Skid Steer mounting plate into position under the
universal quick mount hitch saddle. Once this is
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 4: Optional Equipment
Section 4: Optional Equipment
Front Mounted Gauge Wheel
Refer to Figure 4-1:
The Front mounted gauge wheel will aid in floating the
cutter over uneven terrain making the operator’s job
easier and helps protect against running the cutter frame
into the ground.
Gauge Wheel Assembly . . . . . . . . . . . . . . . 326-004A
24549
Gauge Wheel Assembly
Figure 4-1
Skid Shoe Bundles
Refer to Figure 4-2:
There are two skid shoe bundles available. The standard
skid shoe bundle is constructed of 1/4" x 2" flat bar and
the heavy skid shoe bundle is constructed of 3/8" x 3" flat
bar. The heavy skid shoes will wear longer and withstand
more abuse.
Standard Skid Shoe Bundle . . . . . . . . . . . . .326-027A
Heavy Skid Shoe Bundle . . . . . . . . . . . . . . .326-028A
24588
Skid Shoe Bundle
Figure 4-2
Motor and Hose Assembly
Refer to Figure 4-3:
There are three motor and hose assembly options to
meet your Skid Steer requirements. All three assemblies
are interchangeable and do not require adapter kits.
Compare your motor’s GPM rating located on an
attached decal with the GPM ratings below:
Low Volume Motor & Hoses. . . . . . . . . . 11 - 16 GPM
Medium Volume Motor & Hoses. . . . . . . 17 - 21 GPM
High Volume Motor & Hoses . . . . . . . . . 22 - 27 GPM
If your cutter’s motor and hose assembly is not
compactible with your Skid Steer, you should replace it
with one of the following assemblies:
Low Volume Motor & Hoses Assy . . . . . . . 326-013A
Medium Volume Motor & Hoses Assy . . . . 326-014A
High Volume Motor & Hoses Assy. . . . . . . 326-015A
24587
Motor and Hose Assembly
Figure 4-3
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 4: Optional Equipment
Extended Hose Kit
Refer to Figure 4-4:
Some Skid Steer hydraulic connections are located
farther away from the motor. Standard set-up includes
two 80" long hoses and one 82" long return hose. The
Extended Hose Kit includes two 116" long hoses and one
118" long return hose.
Extended Hose Kit . . . . . . . . . . . . . . . . . . . .326-016A
24589
Extended Hose Kit
Figure 4-4
Operator Protective Door
Refer to Figure 4-5:
The Skid Steer MUST be equipped with an operator
protective door for shielding against flying debri when
attached to a Rotary Cutter. Land Pride offers a universal
shield that attaches to your Skid Steer’s hand hold with
two u-bolts. Some notching in the shield may be required
to fit your particular Skid Steer model. See “Operator
Protective Door (Optional)” on page 13 for additional
information.
Protective Door Kit . . . . . . . . . . . . . . . . . . . .326-024A
24609
Operator Protective Door
Figure 4-5
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 5: Maintenance & Lubrication
Section 5: Maintenance & Lubrication
d. Always grind the cutting edge so that the end of
the blade remains square to the cutting edge and
not rounded.
Maintenance
Proper servicing and adjustment is the key to the long life
of any implement. With careful and systematic inspection,
you can avoid costly maintenance, time and repair.
e. Do not sharpen the back side of the blade.
f. Both blades should weigh the same after
sharpening with not more than 1 1/2 oz.
difference. Unbalancedbladeswillcauseexcessive
vibration which can damage gearbox bearings and
create structural cracks.
After using your Rotary Cutter for several hours, check all
bolts to be sure they are tight.
Replace any worn, damaged or illegible safety labels by
obtaining new labels from your Land Pride Dealer.
6. Carefully check cutting edges of blades in relation to
blade carrier rotation to ensure correct blade
placement. Cutter blades must be installed with
cutting edge leading in rotation and airfoil (lift) must be
oriented towards the top of the deck.
Cutter Blade Maintenance
!
DANGER
Always disconnect hydraulic hoses from the Skid Steer before
servicing underside of deck. The motor can be engaged if Skid
Steer is started resulting in possible damage to the cutter,
bodily injury and/or death.
Refer to Figure 5-1:
IMPORTANT: Shim (#2) below may or may not be
required. If blade deflection is less than 3/4" without
a shim, then the shim is not used. However, a shim
is required if blade deflection is greater than 3/4".
!
WARNING
Always secure the cutter deck in the up position with solid
supports before servicing the underside. Never work under
equipment supported by hydraulics. Hydraulics can drop
equipment if controls are actuated or if hydraulic lines burst.
Either situation can drop the cutter instantly even when power
to the hydraulics is shut off.
IMPORTANT: Locknuts can loose their ability to lock
properly once removed. Therefore, always use a
used blade nut or plain nut in steps 7 & 8 below and
then replace used nut with new locknut in step 9.
7. Start by assembling blades without shim (#2). Insert
blade bolt (#1) through blade (#3), dish pan (#4) and
flat washer (#5). Temporarily secure blade with a used
1 1/8"-12 nut. Draw nut up snug. Do not tighten.
IMPORTANT: Replacement blades should be
ordered in pairs. Order only genuine Land Pride
blades. Other blades may not meet specifications.
Always inspect cutting blades before each use. Make
certain they are properly installed and are in good
working condition. Replace any blade that is damaged,
worn, bent, or excessively nicked. Small nicks can be
ground out when sharpening.
3/4" maximum
blade deflection
when blade
bolts are tight
Remove cutting blades and sharpen or replace as follows:
1. Align blade bolt with access hole in deck.
2. Place skid steer in park and/or set brakes, shut engine
off and remove ignition key.
3. Always disconnect hydraulics from Skid Steer and
secure cutter deck in the up position with solid
supports before servicing underside of cutter.
24590
Cutter Blade Assembly
Figure 5-1
4. See Figure 5-1. Unscrew locknut (#6) to remove
cutting blade (#3). Blade bolt (#1) is keyed and will
not turn freely.
8. Check blade deflection. If deflection is greater than
3/4", remove blade bolt and reassemble as before
except include shim (#2) when reassembling. Select
shim thickness based on deflection. The greater the
deflection, the thicker the shim.
5. Both blades should be sharpened at the same angle
as the original cutting edge and must be replaced or
re-ground at the same time to maintain proper
balance in the cutting unit. The following precautions
should be taken when sharpening the blades:
9. Once blade deflection is correct, replace used nut
with new locknut (#6) and torque to 450 ft. lbs.
a. Do not remove more material than necessary.
b. Do not heat and pound out a cutting edge.
10. If replacing dishpan (#4), nut on gearbox output shaft
should be torqued to 450 ft-lbs. minimum and secured
with a cotter pin installed through the nut and bolt and
both legs bent opposite directions around nut.
c. Do not grind blades to a razor edge. Leave a blunt
cutting edge approximately 1/16” thick.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 5: Maintenance & Lubrication
3. Remove 3/8" hex lock nuts (#4), lock washers (#5), flat
washers (#6), 3/8” plow bolts (#3), three skid shoes
(#1) and one skid shoe (#2) from all four deck corners.
Land Pride Cutter Blade Parts
Item Part No.
Part Description
318-586A BLADE BOLT KIT (Contains #’s 1, 2, 5 & 6)
802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY
312-075D BLADE SPACER 16 GA. (.060")
312-082D BLADE SPACER 18 GA. (.048")
312-089D BLADE SPACER 20 GA. (.036")
4. Plow bolts should be checked for wear and replaced if
necessary.
1
2
2
2
2
3
3
4
4
5
6
5. Install the new short skid shoe (#2) to the back left
deck corner as shown with 3/8”-16 x 1 1/4 GR5 plow
bolts (#2), flat washers (#6), lock washers (#5) and
3/8" hex lock nuts (#4). Torque lock nuts (#4) to
31 ft. lbs.
312-808C BLADE SPACER 24 GA. (.024")
820-112C SC2660 CUTTER BLADE 1/2 x 4 x 25 CW
820-249C SC2672 CUTTER BLADE 1/2 x 4 x 29 CW
316-124H WELDMENT DISHPAN SC2660
312-811H WELDMENT DISHPAN SC2672
804-147C WASHER FLAT 1 HARD ASTMF436
803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE
6. Install the long skid shoes (#1) to the remaining three
deck corners with 3/8”-16X1 1/4 GR5 plow bolts (#2), flat
washers (#6), lock washers (#5) and 3/8" hex lock nuts
(#4). Torque lock nuts (#4) to 31 ft. lbs.
Skid Shoe Maintenance
7. Raise cutter up and remove support blocks.
Land Pride Standard Skid Shoe Bundle 326-027A
!
WARNING
Item Part No.
Part Description
Excessive wear on skid shoes may cause inadequate operation
of cutter and create a safety hazard!
1
2
3
4
5
6
312-602D SKID SHOE, 1/4" x 2"
326-276D DECK RUNNER LH REAR, 1/4" x 2"
802-466C PLOW 3/8-16X1 1/4 GR5
803-013C NUT LOCK 3/8-16 PLT
804-013C WASHER LOCK SPRING 3/8 PLT
804-012C WASHER FLAT 3/8 SAE PLT
Skid shoes should be inspected at the beginning of each
cutting season and replaced when material thickness is
less than 1/8" at any point. Order only genuine Land Pride
parts from your local Land Pride Dealer.
Refer to Figure 5-2:
Replace skid shoes as follows:
Land Pride Heavy Skid Shoe Bundle 326-028A
1. Raise the Rotary Cutter 3" or more off the ground
and place support blocks under the cutter. Make sure
the support blocks are positioned so they will not
interfere with skid shoe installation.
Item Part No.
Part Description
1
2
3
4
5
6
326-343D SKID SHOE HEAVY, 3/8" x 3"
326-344D SKID SHOE HEAVY SHORT, 3/8" x 3"
802-466C PLOW 3/8-16X1 1/4 GR5
803-013C NUT LOCK 3/8-16 PLT
804-013C WASHER LOCK SPRING 3/8 PLT
804-012C WASHER FLAT 3/8 SAE PLT
2. Lower cutter onto the support blocks, place Skid Steer
in park, set park brakes, shut the Skid Steer off and
remove switch key.
24546
Skid Shoe Replacement
Figure 5-2
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
24
Land Pride
Section 5: Maintenance & Lubrication
Storage
Hydraulic Maintenance
!
!
CAUTION
DANGER
Store cutter with hitch plate in the upright position. A hitch
plate that is stored folded down against the deck can tip up
easily resulting in serious injury to the body.
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be treated by a
doctor within a few hours or gangrene may result.
!
DANGER
Do not modify the Rotary Cutter without authorization from
Land Pride. Unauthorized modifications to the cutter can
result in the cutter not performing properly and/or in serious
injury or death.
One of the most important things you can do to prevent
hydraulic system problems is to ensure that your Skid
Steer reservoir remains free of dirt and contamination.
Use a clean cloth to wipe the hose ends before attaching
them to your Skid Steer. Replace the filter element for
your Skid Steer’s hydraulic system at the prescribed
intervals. These simple maintenances will go a long way
to prevent occurrence of hydraulic problems.
Clean the Rotary Cutter at the end of the working season
or when the cutter will not be used for a long period.
1. Clean off any dirt or grease that may have
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of the deck and
then wash the surface thoroughly with a garden hose.
A coating of oil may also be applied to the lower deck
area to minimize oxidation.
2. Check blades and blade bolts for wear and replace if
necessary. See “Cutter Blade Maintenance” on
3. Inspect for loose, damaged or worn parts and adjust
or replace as needed.
4. Lubricate as noted in the Lubrication portion of this
section starting on page 26.
5. Store the Rotary Cutter in a clean, dry place. The
deck should be positioned on a flat surface to suitable
Skid Steer hook-up height. Ensure that the main
frame is stable. Use auxiliary supports or posts if
necessary to prevent the possibility of the unit tipping
over. Store hitch in the upright position.
6. Repaint parts where paint is worn or scratched to
prevent rust. Ask your dealer for Aerosol Land Pride
touch-up paint.
Land Pride Touch-up Paint
Part Description
Part No.
821-002C
PAINT GP BLACK SPRAY CAN
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
25
Land Pride
Section 5: Maintenance & Lubrication
Lubrication Points
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
Intervals in hours
at which lubrication
is required
25
24544
25
Hours
Lubrication Points
Hitch Plate Pivot
2 - Zerks
Type of Lubrication: Multi-purpose Grease
Quantity = As required
25
Hours
Gauge Wheel Parallel Arms
4 - Zerks
Type of Lubrication: Multi-purpose Grease
Quantity = As required
24549
25
Hours
Gauge Wheel Spindle & Axle Hub
1- Zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required
24549
25
Hours
Axle Hub Bearing
1- Zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required
24549
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
26
Land Pride
Section 5: Maintenance & Lubrication
8
Hrs.
Motor Spindle Hub (SC2660 Only)
The motor spindle hub (#1), has two cavity plugs (#2)
located on the hitch side of the hub housing.
1. Disengage blade hydraulics. Make sure blades have
come to a complete stop.
2. Disconnect float chains from cutter deck at mounting
holes “A” (See Figure 2-3 on page 16).
3. Disconnect height adjustment safety chain from front of
loader (See Figure 2-3 on page 16).
4. Raise front of cutter off the ground and tilt hitch forward
until cutter is hanging from the hitch straight down.
SC2660 Spindle Hub Lubrication
5. Set park brake, shut engine off and remove switch key
before continuing.
6. Remove one of the cavity plugs (#2) to check fluid level.
Fluid level should be within 1/2" from top of port opening.
7. Add EP 80-90 weight gearlube as required. Full capacity
of motor housing is approximately 1/3 pint.
8. Install cavity plug and tighten.
9. Being careful not to damage the tail wheel, lower cutter
back to ground level.
10. Reattach adjustment safety chain and float chains.
Do Not
Overfill
8
Hrs.
Gearbox (SC2672 Only)
IMPORTANT: Do not overfill! Level cutter and wait for
gearbox oil to cool before checking. An unlevel cutter or
a gearbox with hot oil will not show correct oil level.
Unscrew vent plug with dipstick. Wipe oil from dipstick and
screw it back in without tightening. Unscrew again and
check oil level mark. If low, fill through top plug hole with
EP 80-90Wt oil until oil reaches full mark. Reinstall vent
plug with dipstick and tighten.
23582
SC2672 Gearbox Lubrication
IMPORTANT: Your cutter is shipped with the
gearbox vent plug with dipstick packaged in the
Operator’s Manual bag and should have been
installed in the gearbox by your Land Pride dealer.
Please see your Land Pride dealer if the vent plug
with dipstick was not included.
Type of Lubrication: Gear Lube EP 80-90W
Quantity = Fill until oil reaches full mark on dipstick.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications & Capacities
Section 6: Specifications & Capacities
SC2660 & SC2672 Skid Steer Rotary Cutter
Description
SC2660
60"
SC2672
72"
Cutting Width
Overall Width
Overall Length
65 1/2"
73"
78"
91"
Cutter Weight Without Gauge Wheel
Gauge Wheel Weight (Optional)
Skid Shoe Weight (Optional)
1004 lbs.
1256 lbs.
114 lbs.
Standard skid shoes = 15 lbs.
Heavy-duty skid shoes = 25 lbs.
Cutting Height
Gearbox Oil
1 1/2" to 18" infinitely variable.
Does Not Apply
EP 80-90 Wt. Gearlube
Spindle Hub Oil
EP 80-90 Wt. Gearlube
Does Not Apply
Low Volume Motor Blade Tip Speed
Medium Volume Motor Blade Tip Speed
High Volume Motor Blade Tip Speed
18,540 fpm at 16 gpm.
18,850 fpm at 21 gpm.
19,000 fpm at 27 gpm.
Not Applicable
17,200 fpm at 21 gpm.
18,550 fpm at 27 gpm
Blade Size
1/2" x 4" updraft.
Clockwise
Blade Rotation
Blade Bolt
1 1/8"-12 x 3 7/16" with key.
Heavy duty round pan stump jumper.
2" Diameter
Dishpan
Cutting Capacity
Deck Thickness
Upper Deck = 16 Ga.
Lower Deck = 10 Ga.
Side Skirt Construction
1/4" Steel
Single row chain guard.
Front Deck Protection
Rear Deck Protection
Double row chain guard.
Safe chain limiter.
Deck Lift Height Protection
Deck Wear Protection (Optional)
Skid Shoes Construction (Optional)
Optional four corner mounted skid shoes.
Standard-duty skid shoes = 1/4" x 2" steel
Heavy-duty skid shoes = 3/8" x 3" steel
Operator Protection (Optional)
Cutting Height Gauging (Optional)
Low Volume Drive Motor
Medium Volume Drive Motor
High Volume Drive Motor
Hydraulic Pressure
Protective door shield.
Pivoting and adjustable front mounted gauge wheel with laminated tire.
11-16 gpm flow
Not Available
17-21 gpm flow
22-27 gpm flow
1500 to 3000 psi.
Hitch
Universal floating-hitch mounting plate. Hitch plate can be mounted centered
on the deck or mounted to offset the deck to the right 8 1/2".
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
28
Land Pride
Section 7: Features and Benefits
Section 7: Features and Benefits
SC2660 & SC2672 Skid Steer Rotary Cutter
Features
Benefits
Surpassed Rugged
Industry Standards
All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.
Low Volume Motor @ 11-16 gpm
Medium Volume Motor @ 17-21 gpm
High Volume Motor @ 22-27 gpm
Customer can chose one of three optional motors for his SC2660 cutter or one of
two optional motors (medium and high volume) for his SC2672 cutter. This allows
the cutter to fit a wide variety of Skid Steers. Also the deck can be upgraded to a
different motor when owner upgrades his Skid Steer.
Two Year Gearbox & Motor Warranty Shows Land Pride’s confidence in the gearbox and motor.
Smooth Deck Top
No pockets to collect rain and dirt. Easy to clean.
1/4” Side Panels for
Protects sides from debris being thrown against them from the blades.
Overall Reinforcement
Front and Rear Chain Shields
Single chain on the front and double chain on the rear. Reduces flying debris.
Protect side plate structure. Shoes are replaceable for convenience.
(Optional) Replaceable
Skid Shoes
Splined Blade Bar
Allows for tight positive fit of stump jumper and blade bar to motor output shaft.
3/16” Round Stump Jumper
Standard stump jumper aids in sliding over obstructions, which helps protect
gearbox output shaft.
1/2” x 4” Heat-treated
Free Swinging Blades
Heat-treated blades offer longer life.
Free swinging blades protect from obstructions.
2” Diameter Cutting Capacity
SC2660 High Blade Tip Speed
Can aid in clearing brush.
Low volume motor = 18,540 fpm at 16 gpm.
Medium volume motor = 18,850 fpm at 21 gpm.
High volume motor = 19,000 fpm at 27 gpm.
SC2672 High Blade Tip Speed
Medium volume motor = 17,200 fpm at 21 gpm.
High volume motor = 18,550 fpm at 27 gpm.
Offset Hitch (8 1/2" to the right)
Optional Front Gauge Wheel
Allows the operator to cut close to obstacles on the right side.
Provides easy operation and handling over uneven terrain, laminated tire can’t go
flat.
Floating Hitch Mounting Plate
Allows smoother travel over rough terrain with the optional gauge wheel easing the
fatigue put on the operator.
Optional Operator Protection Door
Lift Limit Safety Chain
Provides additional operator protection from flying objects.
Provides additional operator protection from flying objects by allowing the Rotary
Cutter to only be lifted up to 18".
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Troubleshooting
Section 8: Troubleshooting
Troubleshooting Chart
Problem
Cause
Solution
Motor Oil Seal Leaking
Return line from motor has been pinched
or is collapsed.
Replace lower seal of motor. Check motor
return hose for kinks.
Case drain line is not properly connected.
Connect case drain line to the hydraulic
motor and skid steer reservoir.
Spindle Hub Seal Leaking
Return line from motor has been pinched
or is collapsed.
Replace lower seal of motor and Spindle
Hub output shaft seal. Check motor return
hose for kinks.
Blades wearing excessively
Spindle Hub Seal Leaking
Cutting on sandy ground.
Raise cutting height.
Raise cutting height.
Contacting ground frequently.
Return line from motor has been pinched
or is collapsed.
Replace lower seal of motor and Spindle
Hub output shaft seal. Check motor return
hose for kinks.
Blades coming loose
Insufficient shimming.
Add shimming. See text.
Blade bolts not tightened properly.
Running loose in the past.
Torque blade bolt nuts to 450 ft lbs.
Blade carrier becomes loose
Replace gearbox output shaft and blade
carrier.
Blade carrier hardware not tight enough.
Blade hardware running loose.
Hitting solid objects.
Tighten to specified torque.
Blade bolt holes worn
Blades breaking
Replace blades and blade bolts if worn.
Thoroughly check the cutting area
BEFORE beginning to cut. Be alert during
cutting.
Loose Blade Carrier
Worn spindle hub bearings.
Replace Spindle Hub bearings and/or
shaft.
Shaft nut loose.
Tighten Spindle Hub shaft nut to 450 ft lbs.
Avoid solid objects/Be alert.
Adjust rate of drop.
Blade Carrier bent
Hitting solid objects.
Lowering too fast.
Gauge wheel support failing
Hitting objects when turning.
Cutting height not level or blade missing.
Soil abrasive.
Reduce speed on turns.
Excessive skid shoe wear
Excessive vibration
Adjust deck height or replace.
Raise cutting height.
Cutting too low.
Raise cutting height.
Locked blades.
Inspect and unlock blades.
Replace blades as a PAIR.
Replace / straighten blade carrier.
Blades have unequal weight.
Blade carrier bent.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
30
Land Pride
Section 9: Appendix
Section 9: Appendix
Torque Values Chart
Bolt He a d Id e ntific a tion
Bolt He a d Id e ntific a tion
8.8
10.9
5.8
Bolt Size
(Inc he s)
Bolt Size
(Me tric )
Class 5.8
Class 8.8
Class 10.9
Grade 2
Grade 5
Grade 8
1
3
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
N · m ft-lb N · m ft-lb N · m ft-lb
mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb
7.4
8.5
15
5.6
11
8
16
12
M 5 X 0.8
4
3
6
5
9
7
6
13
10
18
14
M 6 X 1
7
5
11
8
15
11
11
24
17
33
25
M 8 X 1.25
M 8 X 1
17
12
26
19
36
27
17
13
26
19
37
27
18
13
28
21
39
29
27
20
42
31
59
44
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
33
24
52
39
72
53
31
22
47
35
67
49
39
29
61
45
85
62
43
32
67
49
95
70
58
42
91
67
125
130
145
200
l215
315
335
405
485
610
900
93
49
36
75
55
105
145
165
210
235
285
325
510
570
820
905
78
60
44
95
70
97
66
49
105
115
150
165
205
230
360
405
585
640
875
955
76
105
120
155
170
210
240
375
420
605
670
90
66
105
145
155
225
240
310
350
440
650
760
830
77
105
150
160
230
245
300
355
450
665
75
55
85
M14 X 2
92
68
105
115
165
180
230
260
325
480
560
610
95
70
110
120
150
170
265
295
430
475
645
705
M14 X 1.5
M16 X 2
99
73
105
130
150
235
260
225
250
340
370
480
540
680
750
890
79
145
155
195
220
280
310
480
525
960
105
115
145
165
205
230
355
390
705
97
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
110
170
190
165
185
250
275
355
395
500
555
655
7/8" - 14
1" - 8
1050 780
1150 845
1230 910
1350 995
1750 1290
1960 1440
M24 X 2
1" - 12
M30 X 3.5
M30 X 2
1510 1120 2100 1550
1680 1240 2320 1710
1-1/8" - 7
1 1/8" - 12
1 1/4" - 7
1 1/4" - 12
1 3/8" - 6
1 3/8" - 12
1 1/2" - 6
1 1/2" - 12
1080 795
1210 890
1060 785
M36 X 3.5
1730 1270 2650 1950 3660 2700
1880 1380 2960 2190 4100 3220
1520 1120 2460 1820
1680 1240 2730 2010
1990 1470 3230 2380
2270 1670 3680 2710
2640 1950 4290 3160
2970 2190 4820 3560
M36 X 2
1
in-tpi = nominal thread diameter in inches-threads per inch
N· m = newton-meters
2
3
4
1010 745
1180 870
1330 980
ft-lb= foot pounds
mm x pitch = nominal thread diameter in millimeters x thread
pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Additional Torque Values
Wheel Hub Stub 1/2"-20x1 5/8Gr 5
Blade Bolt Lock Nut
85 ft-lbs.
450 ft-lbs
450 ft-lbs
Blade Carrier Hub Nut
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
31
Land Pride
Section 9: Appendix
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Gearbox & Motor: Two years Parts and Labor.
Hoses and seals: Considered wear items.
Blades and Tires: Considered wear items.
This Warranty is limited to the replacement of any defective part by Land
Pride and the installation by the dealer of any such replacement part, and does
not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials
or design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in
this written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days
from the date of purchase by the end user.
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Download from Www.Somanuals.com. All Manuals Search And Download.
1/07/09
33
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|