La Crosse Technology Weather Radio 308 146CA User Manual

308-146CA FAQS  
The links below will work in most PDF viewers and link to the topic area by  
clicking the link. We recommend Adobe Reader version 10 or greater  
CONTENTS  
La Crosse Technology, Ltd.  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
A/C Power  
The design of this Weather Station is to use a/c power (5-volt) as primary power source.  
When operating with the a/c power cord the backlight can be on continually.  
When operating on a/c power, batteries are optional and not required in the Weather  
Station.  
The backlight will turn off or operate at high or low intensity at your discretion.  
IMPORTANT: When operating on a/c power, to avoid interference, the backlight and USB  
charging port will turn off while the Weather Station searches for the WWVB signal. The  
backlight will return after the 2-10 minute search (which occurs during the late night or early  
morning hours). Then the USB charging port will resume working.  
Weather Station Factory Restart  
FACTORY RESTART:  
DISTANCE: Bring the transmitter and Weather Station together inside and place both 5-10  
feet apart with nothing between them.  
REMOVE POWER: Remove batteries and a/c cord from transmitter and Weather Station.  
DISCHARGE ELECTRICITY: Press one of the buttons on the Weather Station at least 20  
times to clear all memory. Verify that the Weather Station is blank before proceeding.  
UNPOWERED 10 MINUTES: Let the Weather Station and transmitter sit with power  
removed for at least 10 minutes.  
WEATHER STATION: Insert 5-volt A/C power cord or install fresh alkaline batteries in the  
Weather Station.  
TRANSMITTER: Insert fresh batteries into the transmitter, observing the correct polarity.  
PRESS TX BUTTON: Press the TX button on the back of remote Transmitter to transmit RF  
(radio frequency) signal. Keep the transmitter 5-10 feet from the Weather Station.  
WAIT: Wait for 5 minutes for the outdoor temperature/humidity to appear.  
CONNECTION: When RF (radio frequency) connection is established, the respective  
temperature & humidity will appear on the main unit. Allow the transmitter and Weather  
Station to sit together for 15 minutes to establish a strong connection.  
PLACE TRANSMITTER OUTSIDE: For optimum 433MHz transmission, place the outdoor  
transmitter a distance of no more than 200 feet (60 meters, open air) from the Weather  
Station.  
See the section on mounting and distance/resistance/interference for details on mounting  
the outdoor transmitter.  
Outdoor Temperature/Humidity Transmitter  
Compatible Outdoor Transmitters  
A TX14TH outdoor transmitter comes packaged with this Weather Station.  
The TX14TH, TX14TH-LCD-G and TX14TH-LCD-B (433MHz) transmitters are compatible  
with this Weather Station.  
Quick Connect  
DISTANCE: Bring the transmitter and Weather Station together inside and have both units  
5-10 feet apart with nothing between them.  
WEATHER STATION: Hold the CH button on the Weather Station for 5 seconds until the  
temperature/humidity area starts to flash.  
TRANSMITTER: Remove battery cover and press and release the TX button to send the  
signal.  
WAIT: Wait for 2 minutes for the outdoor temperature/humidity to appear.  
Factory Restart: If the above procedure does not work, please try the factory reset below.  
La Crosse Technology, Ltd.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Power requirements  
2-AA batteries power the outdoor transmitter.  
We recommend alkaline batteries for the transmitter.  
You may choose to use lithium batteries for temperatures below - 20°F/-28.8°C.  
Dashes shown for Outdoor Temperature/Humidity  
Dashes means the connection is lost between the Weather Station and the outdoor  
transmitter.  
Batteries often resolve the connection.  
Distance/Resistance can cause loss of connection between the transmitter and the Weather  
Station.  
Reorientation of the Weather Station 90 degrees towards the outdoor transmitter may  
provide better reception. This allows more antenna surface to face the transmitter signal.  
Outdoor Temperature/Humidity changes constantly  
The Weather Station can read up to three outdoor transmitters.  
Check the channel indicator. If it switches between 1, 2 or 3, your Weather Station is  
reading additional transmitters.  
The word AUTO will appear below the channel indicator when the Weather Station is set to  
Press and release the CH button to settle on one channel.  
Note: When first powered up it is natural for the Weather Station to search across all three  
channels for up to 15 minutes for outdoor transmitters.  
You may have an additional compatible outdoor transmitter within range.  
Occasionally a neighbor will have a compatible outdoor transmitter that is within range.  
Inaccurate Outdoor Temperature/Humidity reading  
The outdoor transmitter reads the environment. When mounted in the home it will read  
inside temperature/humidity.  
When the transmitter reads high during the day but not at night it is a positioning problem.  
Side-by-side test: Bring the outdoor transmitter in the house and place it next to the  
Weather Station for 2 hours.  
Compare indoor and outdoor temperature. The temperatures should be within 4 degrees to  
be within tolerance. The humidity should be within 10% to be within tolerance. See the  
section on accuracy for details.  
If the transmitter reads correctly when next to the Weather Station then try a different  
location outside.  
Look for heat sources such as sunlight, door or window frames, or reflected heat.  
Intermittent Outdoor Temperature/Humidity  
RF (radio frequency) communication may come and go occasionally. This can be normal in  
some environments (e.g. moister climates). If transmitter signal is lost, please wait 2-4 hours  
for the signal to reconnect on its own.  
Move the outdoor transmitter to a closer location.  
Check Channels: Confirm that the channel selected on the outdoor transmitter matches the  
channel shown on the Weather Station.  
La Crosse Technology, Ltd.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Freezer test: Confirm the Weather Station is reading the correct outdoor transmitter. Place  
the transmitter in the freezer for an hour and watch the temperature drop on the Weather  
Station.  
Indoor distance test: Please complete the Restart with transmitter and Weather Station 5-  
10 feet apart and inside to establish a strong connection.  
After 15 minutes if there is a reading in the outdoor temperature area, move the transmitter  
to another room with one wall between the transmitter and the Weather Station. Observe to  
see if the temperature/humidity remains on consistently for 1-hour.  
If the temperature/humidity remains on while in the house then it is likely a  
distance/resistance issue. Move the transmitter to different locations outside to find a  
location where the temperature/humidity reading will hold.  
Distance/Resistance can cause loss of transmitter signal.  
Outdoor Temperature/Humidity is stuck or OFL  
The last outdoor reading may remain (not change) for several hours when connection is lost.  
The outdoor temperature/humidity reading will flash when the connection is first lost or  
intermittent between the Weather Station and the outdoor transmitter.  
Check Batteries. Overpowered or underpowered batteries can cause this reading.  
Replace outdoor transmitter.  
Outdoor transmitter fell and no longer works  
If there is no physical damage to the outdoor transmitter, the fall may not have caused  
internal damage.  
An outdoor transmitter that has fallen into a puddle or other standing water or snow may  
have water damage.  
Transmitters are water resistant, not waterproof.  
A fall can shock the transmitter or the batteries in the transmitter. Batteries that have fallen  
on a hard surface may be damaged and unable to function properly.  
Complete a Restart with fresh batteries.  
Use Batteries dated at least six years in advance of the current year. Batteries dated earlier  
than six years from now may still work, but may be unstable in performance.  
Outdoor Transmitter drains batteries quickly  
Test a new set of alkaline batteries. Write down the date of installation and the voltage of the  
batteries.  
When the batteries fail, please note the date and voltage again.  
Check the distance and resistance between the transmitter and Weather Station.  
Transmitters at the end of the range may work while batteries are fresh but not after they  
drain a bit.  
Check for leaking batteries, which may damage the transmitter.  
Battery life is over 24 months when using reputable battery brands for both Alkaline and  
Lithium batteries.  
MIN/MAX Temperature readings  
This Weather Station will show the daily minimum and maximum temperatures starting at  
midnight (12:00 AM).  
The Weather Station will automatically reset the min/max temperatures at midnight (12:00  
AM).  
You can manually reset the MIN/MAX data at any time.  
La Crosse Technology, Ltd.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
VIEW MIN/MAX:  
MAX: From a normal display press and release the MIN/MAX button once to view maximum  
temperature and humidity values for indoor and outdoor data. The word MAX will appear  
next to the indoor and outdoor temperature.  
MIN: From a normal display press and release the MIN/MAX button once to view minimum  
temperature and humidity values for indoor or outdoor data. The word MIN will appear next  
to the indoor and outdoor temperature.  
MANUAL RESET MIN/MAX: Hold the MIN/MAX button for 5 seconds to reset all indoor and  
outdoor minimum and maximum values.  
TIP: When using multiple transmitters, use the CH button to view MIN or MAX temperature on  
the other channels.  
Heat Index/Dew Point temperature  
HEAT INDEX:  
Heat Index combines the effects of heat and humidity. It is the apparent temperature of how hot  
it feels to a human being. As humidity increases, the body is unable to cool effectively. The  
temperature will feel warmer.  
VIEW HEAT INDEX: From a normal display, press the HEAT/DEW button once and Heat Index  
will show instead of the indoor and outdoor ambient temperature.  
Note: Heat index will be the same number as the temperature until the temperature is above 80  
degrees ° F (26.7° C)  
DEW POINT:  
Dew point is the saturation point of the air, or the temperature to which the air has to cool in  
order to create condensation. The higher the dew points, the higher the moisture content of the  
air at a given temperature.  
VIEW DEW POINT TEMPERATURE: From a normal display, press the HEAT/DEW button  
twice and Dew Point will show instead of the indoor and outdoor ambient temperature. The  
words Dew Point will show near the indoor and outdoor temperatures.  
Note: Dew Point is lower than the actual temperature.  
TIP: When using multiple transmitters, use the CH button to view heat index or dew point  
temperature on the other channels.  
Channels  
The Weather Station will accommodate up to three remote outdoor transmitters. The channel  
selection (CH) button on the Weather Station allows you to see the temperature in various  
locations: outdoors, baby’s room, greenhouse, basement, etc.  
Press and release the CH button to view channel 1, 2 or 3 on the display when multiple  
transmitters are used.  
Note: You cannot change channels if only one transmitter is connected.  
CHANNEL SCROLL- Press and release the CH button until you see the word AUTO appear in  
the outdoor data area. The display will automatically rotate through the channels for all  
connected transmitters.  
Press and release the CH button to lock the display into one channel.  
Then view channels individually with a press of the CH button.  
La Crosse Technology, Ltd.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Multiple Outdoor Transmitters  
To connect multiple remote transmitters to the Weather Station:  
Remove the battery cover from all the transmitters (leave off for setup).  
Set the first outdoor transmitter to channel 1 and insert 2-AA batteries.  
Set the second outdoor transmitter to channel 2 and insert 2-AA batteries.  
Set the third outdoor transmitter to channel 3 and insert 2-AA batteries.  
Press and hold CH button on Weather Station until a beep sounds.  
The Weather Station will search for all outdoor transmitters.  
Press the TX button on the back of each outdoor transmitter to transmit RF (radio frequency)  
signal.  
When RF (radio frequency) connection is established, the respective temperature & humidity  
of the selected channels will appear on the main unit.  
Allow the transmitters and the Weather Station to stay 5-10 feet apart for 15 minutes to  
establish a solid connection.  
Install the battery covers on each sensor.  
After 15 minutes, place the remote transmitters in appropriate locations within range of the  
display.  
Press and release the CH button to view channel 1, 2 or 3 on the display when multiple  
transmitters are used.  
Mounting/Positioning Outdoor Transmitter  
Mount outdoor temperature/humidity transmitters vertically and under a bit of an overhang.  
Protect the outdoor transmitter from standing rain or snow, and from the overhead sun,  
which can cause it to read incorrectly. Mounting under an eave or deck rail works well.  
Construct a small roof or box for the transmitter if you do not have an overhang. Please be  
sure it is well vented.  
Mount the transmitter on the North side to prevent sun from causing incorrect readings.  
Mount at least 6 feet in the air for a strong RF (radio frequency) signal.  
Outdoor transmitters are water resistant but not water proof.  
Avoid more than 1 wall between the transmitter and the Weather Station.  
Do not mount near electrical wires, transmitting antennas or other items that will interfere  
with the signal.  
RF (radio frequency) signals do not travel well through moisture or dirt.  
Place the outdoor transmitter and the Weather Station in the desired shaded locations, and  
wait approximately 1-hour before permanently mounting the transmitter to ensure that there  
is proper reception.  
Do not mount the transmitter on a metal fence. This significantly reduces the effective range.  
MOUNT  
Choose a location for the transmitter that is within range of the Weather Station and under  
an overhang for accuracy.  
Install one mounting screw into a wall leaving approximately ½ inch (12.7mm) extended.  
Place the transmitter onto the screw, using the hanging hole on the backside.  
Gently pull the transmitter down to lock the screw into place.  
Note: Always ensure that the transmitter locks onto the screw before releasing.  
Position Weather Station  
The Weather Station has a wide base to sit on a desk or table.  
Place within range of the outdoor transmitter.  
La Crosse Technology, Ltd.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Choose a location 6 feet or more from electronics such as cordless phones, wireless gaming  
systems, televisions, microwaves, routers, baby monitors, etc., which can prevent signal  
reception.  
Be aware of electrical wires and plumbing within a wall. This will interfere with RF (radio  
frequency) signal reception.  
The maximum transmitting range in open air is 200-feet (60 meters).  
Obstacles such as walls, windows, stucco, concrete, and large metal objects can reduce the  
range.  
For best WWVB reception, orientate the Weather Station with the front of the back facing Ft.  
Collins Colorado.  
Distance/Resistance/Interference  
Distance:  
The maximum transmitting range in open air is over 200-feet (60 meters) between the  
outdoor transmitter and the Weather Station.  
This range is in open air with ideal conditions.  
Consider what is in the signal path between the Weather Station and the transmitter.  
Consider the distance the Weather Station is located away from other electronic in the  
home.  
Resistance:  
Obstacles such as walls, windows, stucco, concrete, and large metal objects can reduce the  
range.  
When considering the distance between the transmitter and the Weather Station (200 feet  
open air) cut that distance in half for each wall, window, tree, bush or other obstruction in the  
signal path.  
Closer is better.  
Windows reflect the RF (radio frequency) signal.  
Metal absorbs the signal and reduces the range.  
Stucco is often attached to the wall with a metal mesh that absorbs the signal.  
Do not mount the transmitter on a metal fence. This significantly reduces the effective range.  
Interference:  
Consider items in the signal path between the transmitter and the Weather Station.  
Sometime a simple relocation of the transmitter or the Weather Station will correct the  
interference issue.  
Windows can reflect the radio signal.  
Metal will absorb the RF (radio frequency) signal.  
Stucco is backed by a metal mesh that holds it to the wall.  
Transmitting antennas (ham radio, emergency dispatch center, airports, military base etc.)  
Electrical wires (utilities, cable etc.)  
Vegetation is full of moisture and reduces signal.  
Dirt: Trying to receive a signal through a hill is difficult.  
Accuracy  
Indoor Temperature  
Operating temperature range =  
Accuracy ± 2 degrees Fahrenheit  
Resolution = 0.1 degree F  
32 F to 122 F (0C to 50C)  
32 F to 122 F (0C to 50C)  
La Crosse Technology, Ltd.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Indoor Humidity  
Operating Temperature Range =  
Operating humidity range =  
Accuracy +/- 5% RH  
Accuracy +/- 8% RH  
Accuracy +/-12% RH  
32F to 120F (0C to 50C)  
1% RH to 99%  
(@77oF (25oC) , 30%RH to 80%RH)  
(@77oF (25oC) , 20%RH to29%RH & 80%RH to 95%RH)  
(@77oF (25oC) , 1%RH to 19%RH & 96%RH to 99%RH)  
Resolution = 1 % RH  
Outdoor Temperature  
Operating temperature range =  
Accuracy ± 2 degrees Fahrenheit  
Accuracy ± 4 degrees Fahrenheit  
-40 F to 140F (-40C to 60C)  
32 F to 122 F (0C to 50C)  
-40 F to32 F (-40C to 0C) & 122 F to140 F  
(50C to 60C)  
Outdoor Humidity  
Operating humidity range =  
1% RH to 99%  
Accuracy +/- 5% RH  
Accuracy +/- 8% RH  
Accuracy +/-12% RH  
Resolution = 1 % RH  
(@77oF (25oC) , 20%RH to 90%RH)  
(@77oF (25oC) , 20%RH to 30%RH & 80%RH to 95%RH)  
(@77oF (25oC) , 1%RH to 19%RH & 96%RH to 99%RH)  
Barometric Pressure  
Measure range=  
Resolution=  
800mb to 1100mb  
1mb  
23.62 inHg to 32.48 inHg  
Measuring time interval: every 12 minutes  
Weather Station  
How tall are the time numbers  
The time numbers are 0.79 inches tall.  
Power requirements  
This Weather Station is powered by a 5 volt a/c power adapter  
Alternatively, optional 3-AA alkaline batteries may be used.  
Supported times zones  
This Weather Station offers seven time zones:  
AST=Atlantic  
EST= Eastern  
CST= Central  
MST= Mountain  
PST= Pacific  
AKT= Alaska  
HAT=Hawaiian  
The Weather Station is designed to work in North America.  
La Crosse Technology, Ltd.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
12-Hour or 24-Hour time format  
Display the time in 12-hour or 24-hour format.  
Default is 12-hour time.  
Use the Program Menu to switch time formats.  
Fahrenheit/Celsius  
Weather Station: Press and release the -/°C/°F button on the back of the Weather Station  
to switch the temperature display from Fahrenheit to Celsius.  
Backlight goes out  
The backlight will automatically go dark when the Weather Station is searching for a WWVB  
time signal.  
The backlight will return after the 2-10 minute search.  
The WWVB signal search will occur when the Weather Station during setup and  
automatically during the late night or early morning hours.  
Press and release the LIGHT HI/LO button to be sure the backlight was not on dim.  
Hold the LIGHT HI/LO button to be sure the backlight was not off.  
Check that the a/c cord is correctly inserted into the Weather Station and outlet. The  
backlight will not show constantly on battery power.  
Backlight  
A/C adapter:  
The backlight can show continuously when operating the Weather Station with the 5-volt a/c  
adapter.  
HIGH: The backlight is defaulted to HI (brightness) when the a/c adapter is in use.  
LO: Press and release the LIGHT HI/LO button to dim the brightness of the backlight.  
Press and release the LIGHT HI/LO button again to return to full strength (HIGH).  
Note: When the Adapter is NOT in use, the High/Low backlight feature is not available.  
OFF: Hold the HOLD ON/OFF button for 5 seconds, until the station beeps, to turn the  
backlight off to sleep.  
ON: Hold the HOLD ON/OFF button again until the station beeps, to turn the backlight on.  
The backlight will come on at the same level (high or low) as it was set to when turned off.  
Note: When the backlight is off, press any button to activate the backlight for 8 seconds, and  
then it will turn off again.  
Battery power:  
Press and release the SNOOZE/LIGHT button and the backlight will show for 8 seconds, when  
operating on batteries only.  
IMPORTANT: When operating on a/c power, the backlight and USB charging port will turn off  
while the Weather Station searches for the WWVB signal, to avoid interference. The backlight  
will return after the 2-10 minute search (which occurs during the late night or early morning  
hours). Then the USB charging port will resume working.  
La Crosse Technology, Ltd.  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Dashes, OFL or stuck indoor Temperature/Humidity  
This is generally a power related issues.  
Check that the a/c cord is correctly inserted into the Weather Station and outlet. If using  
batteries in the Weather Station as well, remove them and see if the Weather Station goes  
blank, indicating a faulty a/c cord.  
Batteries may be overpowered or underpowered. Remove batteries and a/c cord from  
Weather Station.  
Press any button 20 times. Leave the Weather Station unpowered for 1-2 hours.  
Insert a/c power cord into an outlet then into the Weather Station.  
Alternatively, install fresh alkaline batteries with correct polarity.  
If the indoor temperature/humidity is still dashes or OFL, the Weather Station may need to  
be replaced.  
Inaccurate indoor Temperature/Humidity reading  
Side-by-side test: Bring the outdoor transmitter in the house and place it next to the  
Weather Station for 2 hours.  
Compare indoor and outdoor temperature/humidity. The temperature should be within 4  
degrees to be within tolerance. The humidity should be within 10% to be within tolerance.  
See the section on accuracy for details.  
Look for heat sources such as sunlight, door or window frames, or reflected heat of cold.  
Set time alarm  
ALARM HOUR: Press and hold the ALARM button to enter alarm time setting mode. The  
Alarm Hour will flash. Use the +/RCC or -/°F/°C button to set the Hour. Press and release  
the ALARM button.  
ALARM MINUTE: The Alarm Minutes will flash. Use the +/RCC or -/°F/°C button to set the  
Minutes. Press and release the ALARM button to exit.  
Activate/Deactivate time alarm  
ACTIVATE:  
From the time mode, press and release the ALARM button once to show Alarm Time.  
With the Alarm time showing, press and release the ALARM button to activate the alarm.  
The alarm icon (bell) appears when alarm is activated.  
DEACTIVATE:  
From the time mode ,press and release the ALARM button once to show Alarm Time.  
With the Alarm time showing, press and release the ALARM button to deactivate the alarm.  
The alarm icon will disappear when alarm deactivates.  
Snooze Alarm  
When the alarm sounds, press the SNOOZE button to trigger snooze alarm for 9 minutes.  
The snooze icon Zz will flash when the snooze feature is active.  
To stop alarm for one day, press AL button, while in snooze mode.  
The alarm icon (bell) will remain solid.  
Time is off by hours  
Check to see if the WWVB Tower icon appears on the Weather Station. If not, the Weather  
Station has not received a WWVB time signal in the past 24-hours.  
La Crosse Technology, Ltd.  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Reposition the Weather Station with the front or back facing Colorado.  
Check that the Time Zone selected correctly reflects your location. Adjust the time zone in  
Check that the DST indicator is correct for your location (most areas observe DST so this  
should be ON). Adjust the DST indicator in the Program Menu.  
Forecast icons inaccurate  
THIS WEATHER STATION LEARNS FORECAST OVER TIME!  
Please allow 3-4 weeks for barometer calibration to generate an accurate forecast.  
IMPORTANT: As the Weather Station builds memory, it will compare the current average  
pressure to the past forty day average pressure for increased accuracy. The longer the Weather  
Station operates in one location the more accurate the forecast icons will be.  
Weather Forecast Icons: This Weather Station has 5 forecast icons that predict the weather  
condition of the next 12-hours based on the change of atmospheric pressure.  
Sunny  
Partly Cloudy  
Cloudy  
Rainy  
Stormy  
The icons forecast the weather in terms of getting better or worse and not necessarily sunny or  
rainy as each icon indicates.  
The weather forecast is about 70-75% correct. As weather conditions cannot be 100% correctly  
forecasted we are not be responsible for any loss caused by an incorrect forecast.  
Manually Set Time/Date: Program Menu  
PROGRAM MENU: The SET button will move through the program menu.  
The +/RCC or -/°C/°F button will change the value.  
WWVB ON/OFF: Hold the SET button 5 seconds and WWVB and the word ON will flash.  
Press and release the +/RCC or -/°C/°F button to turn this to OFF if you do not wish WWVB  
reception. Confirm with the SET button and move to the next item.  
TIME ZONE: EST will flash. Press and release the +/RCC or -/°C/°F button to select a  
different Time Zone:  
·
·
·
·
·
·
·
AST=Atlantic  
EST= Eastern  
CST= Central  
MST= Mountain  
PST= Pacific  
AKT= Alaska  
HAT=Hawaiian  
Confirm with the SET button and move to the next item.  
DAYLIGHT SAVING TIME: DST will flash and the word ON. Press and release the +/RCC  
or -/°C/°F button to turn this to OFF if you do not observe DST. Confirm with the SET button  
and move to the next item.  
12/24 HOUR TIME: 12H will flash. Press and release the +/RCC or -/°C/°F button to select  
24H. Confirm with the SET button and move to the next item.  
La Crosse Technology, Ltd.  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
HOUR: The hour will flash. Press and release the +/RCC or -/°C/°F button to select the  
correct hour. Confirm with the SET button and move to the next item.  
MINUTES: The minutes will flash. Press and release the +/RCC or -/°C/°F button to select  
the correct minutes. Confirm with the SET button and move to the next item.  
YEAR: The year will flash. Press and release the +/RCC or -/°C/°F button to select the  
correct year. Confirm with the SET button and move to the next item.  
MONTH: The month will flash. Press and release the +/RCC or -/°C/°F button to select the  
correct month. Confirm with the SET button and move to the next item.  
DATE: The date will flash. Press and release the +/RCC or -/°C/°F button to select the  
correct date. Confirm with the SET button and exit the program menu  
Note: The Day of the Week will set automatically once the year, month and date are set.  
FAHRENHEIT/CELSIUS: Press and release the -/°C/°F button once to switch from Celsius to  
Fahrenheit temperature display.  
No WWVB tower icon  
The Weather Station has not received a WWVB time signal in the past 24-hours.  
Position the Weather Station for better reception.  
Be sure you have good batteries in the Weather Station or that the a/c cord is properly  
attached.  
Hold the +/RCC button to send the Weather Station on a signal search at night.  
Allow up to 5 nights to receive the time signal.  
IMPORTANT:  
When operating on a/c power, the backlight and USB charging port will turn off while the  
Weather Station searches for the WWVB signal, to avoid interference. The backlight will return  
after the 2-10 minute search (which occurs during the late night or early morning hours). Then  
the USB charging port will resume working.  
USB charge port  
The Weather Station has an integrated USB charging port (on back) that will charge devices  
when the Weather Station is plugged into a power outlet.  
Note: This is a power output (charging) port only. This port will not supply power to the  
Weather Station.  
You cannot use a USB cord from the Weather Station to your computer and operate the  
Weather Station.  
Note: There is not a USB cord included with the Weather Station.  
Connect your existing USB charging cord for your external device to the USB charging  
port on the back of the Weather Station to begin to charge. Charging times will vary.  
Note: Check to be sure that your device will charge with the USB cord it came with. Many  
USB cords are for data transfer only, and cannot be used for charging.  
Output: 1A maximum current USB  
Do NOT overload USB port  
Note: Charging times will vary based on battery depletion and the individual device.  
Note: Many devices may require more power to charge than provided by this Weather  
Station.  
La Crosse Technology, Ltd.  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
IMPORTANT: When operating on a/c power, the backlight and USB charging port will turn off  
while the Weather Station searches for the WWVB signal, to avoid interference. The backlight  
will return after the 2-10 minute search (which occurs during the late night or early morning  
hours). Then the USB charging port will resume working.  
Weather Station has missing segments  
This is generally a power related issues.  
Batteries may be overpowered or underpowered. Remove batteries and a/c cord from  
Weather Station.  
Press any button 20 times. Leave the Weather Station unpowered for 1-2 hours.  
Insert the a/c cord into the outlet first then into the Weather Station.  
Alternatively, install fresh alkaline batteries with correct polarity.  
Weather Station is dim  
Battery Operation:  
Most Weather Stations have a gray background. Place the Weather Station at eye level. Is it  
still dim?  
Weather Stations that sit in the sunlight can develop a cloudy film over time.  
This is generally a power related issue.  
Batteries may be overpowered or underpowered. Remove batteries from Weather Station.  
Press any button 20 times. Leave the Weather Station unpowered for 1-2 hours.  
Install fresh alkaline batteries with correct polarity.  
A/C Power Operation:  
Check that the a/c cord is correctly inserted into the Weather Station and outlet.  
If using batteries in the Weather Station as well, remove them and see if the Weather  
Station goes blank, indicating a faulty a/c cord.  
Check the backlight intensity setting. The backlight can be on high, low or off.  
Weather Station has distorted display  
On a brand new Weather Station check for thin plastic films of printed scratch guard that  
may be on the upper and lower screen of the Weather Station. This thin piece of plastic has  
printed numbers for store displays.  
With all power removed the Weather Station should be blank.  
If numbers still appear, please check for scratch guard.  
Check that the batteries and a/c cord are installed correctly.  
This is generally a power related issue.  
Batteries may be overpowered or underpowered.  
Remove batteries and a/c cord from Weather Station.  
Press any button 20 times. Leave the batteries and a/c cord out of the display for 2 hours.  
Insert a/c power cord into a good outlet first, then into the Weather Station.  
Weather Station display is frozen  
On a brand new Weather Station check for thin plastic films of printed scratch guard that  
may be on the upper and lower screen of the Weather Station. This thin piece of plastic has  
printed numbers for store displays. This can make the Weather Station display appear  
“frozen”.  
With all power removed the Weather Station should be blank.  
If numbers still appear, please check for scratch guard.  
Check that the batteries and a/c cord are installed correctly.  
La Crosse Technology, Ltd.  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
This is generally a power related issue.  
Batteries may be overpowered or underpowered.  
Remove batteries and a/c cord from Weather Station.  
Press any button 20 times. Leave the batteries and a/c cord out of the display for 2 hours.  
Insert a/c power cord into a good outlet first, then into the Weather Station.  
Weather Station is blank: No letters, numbers or dashed lines  
Check that the batteries and a/c cord are installed correctly.  
Batteries may be overpowered or underpowered.  
Remove batteries and a/c cord from Weather Station.  
Press any button 20 times. Leave the batteries and a/c cord out of the display for 2 hours.  
Insert a/c power cord into a good outlet first, then into the Weather Station.  
Weather Station drains batteries quickly  
Test a new set of alkaline batteries. Write down the date of installation and the voltage of the  
batteries.  
When the batteries fail, please note the date and voltage again. This is helpful in  
determining the problem.  
Check for leaking batteries, which may damage the Weather Station.  
Battery life is over 12 months when using reputable battery brands.  
Try a/c power cord instead of batteries to power Weather Station.  
La Crosse Technology, Ltd.  
Page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

La Crosse Technology Pet Fence D000101BG User Manual
Lenmar Enterprises Battery Charger PRO68Q User Manual
Lightolier Work Light FBP750 4P User Manual
LOREX Technology Digital Camera SG21CD7444 User Manual
Marshall electronic Computer Monitor V R241 DLW User Manual
Mazda Automobile 2011 2 User Manual
McAfee Automobile Accessories ASH300 User Manual
Memorex MP3 Player MMP3774 User Manual
Metrologic Instruments Scanner iQ160 User Manual
Metz Flat Panel Television Plasma TV Set User Manual