WS-9412U
Atomic Clock
Instruction Manual
R
Contents
Language
English
French
Page
2
16
Spanish
30
Download from Www.Somanuals.com. All Manuals Search And Download.
I. FUNCTION BUTTONS
1. Hold down the "SET" button for 2 seconds (the se-
lected time zone will flash), press the "SET" button
once more until "On" and "DST" alternate flash where
the Weekday normally appears.
There are 2 function buttons located on the front of the
Atomic Clock. The function buttons are labeled: SET
and +.
2. Press and release the "+" button to turn the DST off,
as will be indicated by the display of "OFF" in the
time LCD.
3. Press and release the "SET" button to confirm the
DST setting, and to advance to select the manual
time setting.
II. TIME ZONE SETTING
1. Hold down the "SET" button for 2 seconds, the de-
fault setting "EST" will flash in the Date LCD.
2. Press and release the "+" button to select the appro-
priate time zone. There are 13 time zones to choose
from:
IV. TIME SETTING
EST(-5)
CST(-6)
MST(-7)
PST(-8)
ALA(-9)
HAW(-10) Hawaiian Time
-11
-12
GMT
-1
-2
-3
ATL(-4)
Eastern Time (default setting)
Central Time
Mountain Time
Pacific Time
Alaskan Time
Note: When the WWVB signal is found, that time will
over-ride the manually set time.
1. Hold down the "SET" button for 2 seconds (the se-
lected time zone will flash), press the "SET" button 3
more times, until the hour "12:00" flashes in the time
LCD.
2. Press and release the "+" button to select the hour.
Note: when setting the hour, "PM" will appear to the left
of the hour display, if it is AM nothing will be displayed.
3. Press and release the "SET" button to confirm the
hour setting, and to shift to select the minutes.
4. Press and release the "+" button to select the minutes.
5. Press and release the "SET" button to confirm the
time setting, and to advance to manually set the
calendar.
Greenwich Mean Time
Atlantic Time
3. Press and release the "SET" button to confirm the
time zone setting, and to advance to DST (Daylight
Saving Time) setting.
V. CALENDAR SETTING
III. DST (DAYLIGHT SAVING TIME) SETTING
Note: The DST default is "On", meaning that the WWVB
will automatically change the time according to Daylight
Saving Time in the spring and fall. For areas that do not
recognize DST changes (Arizona and parts of Indiana)
turn the DST "OFF".
Note: When the WWVB signal is found, that date will
over-ride the manually set date.
1. Hold down the "SET" button for 2 seconds (the se-
lected time zone will flash), press the "SET" button 4
more times, until the default year "00" flashes in the
date LCD.
P.6
P.7
GB
GB
2. Press and release the "+" button to select the year.
3. Press and release the "SET" button to confirm the
year, and to set the month.
4. The default month "1" will flash. Press and release
the "+" button to select the appropriate month.
5. Press and release the "SET" button to confirm the
month, and to set the date.
1. Press and release the "+" button. The display should
now show the month & date/ weekday/ seconds.
2. Press and release the "+" button a 2 time and the
display will return to the normal display.
II. INDOOR TEMPERATURE
The Indoor Temperature appears on the right side of the
Date LCD. The temperature is checked every 10
seconds, and updated whenever there is a change.
6. The default date "1" will flash. Press and release the
"+" button to select the appropriate date.
7. Press and release the "SET" button to confirm the
date, and to set the weekday.
MOUNTING
8. The default weekday "MON" (depends on selected
language) will flash. Press and release the "+" but-
ton to select the appropriate weekday.
Hanging Hole
9. Press and release the "SET" button to confirm the
calendar settings, and to advance to select either ˚F
or ˚C temperature display.
VI. SELECTING ˚F OR ˚C
1. Hold down the "SET" button for 2 seconds (the se-
lected time zone will flash), press the "SET" button
10 more times, until the default "˚F" flashes in the
time LCD.
Foldout Table Stand
2. Press and release the "+" button to toggle between
˚F and ˚C.
There are two possible ways to mount the atomic clock:
3. Press and release the "SET" button to confirm the ˚F
or ˚C selection, and exit the Program Mode.
•
•
use of the foldout table stand, or
wall mounting.
FEATURES & OPERATIONS
I. CHANGING DISPLAY MODE (SECONDS, AND
TEMPERATURE)
I. FOLDOUT TABLE STAND
There are 2 possible display modes to view the day,
seconds, and temperature.The month & date/ weekday/
indoor temperature is the default.
To change the display:
Download from Www.Somanuals.com. All Manuals Search And Download.
P.8
P.9
GB
GB
The foldout table stand leg is located on the backside of
the atomic clock. The hinge is towards the center of the
atomic clock, and the end (with no hinge) needs to be
folded in towards the center. Once the foldout table stand
is extended, place the atomic clock in an appropriate
location.
•
Opening the casings invalidates the warranty. Do
not try to repair the unit. Contact La Crosse Technol-
ogy for Repairs.
TROUBLESHOOTING
Problem: The LCD is faint.
Solution:
II. WALL MOUNTING
1. Replace the batteries.
Problem: "OFL" appears in the LCD.
Solution:
1. Move unit to an area with warmer or cooler surround-
ing temperature. Current surrounding temperatures
are outside measuring range.
Problem: No reception of WWVB signal.
Solution:
1. It may help reception to face the front of the Atomic
Clock in the general direction of Ft. Collins, Colorado.
2. Wait overnight for signal.
3. Be sure the Atomic Clock is at least 6 feet from any
electrical devices, i.e. TV sets, computers, or other
radio controlled clocks.
4. Remove batteries for five minutes, reinsert and leave
the unit alone overnight without pressing buttons.
5. If problems persist contact La Crosse Technology.
1. Place a screw in your desired position on your wall.
2. Install the mounting screw (not included) into a wall -
leaving approximately 3/16 of an inch (5mm) extended
from the wall.
3. Place the Atomic Clock onto the screws, using the
hanging hole on the backside. Gently pull the Atomic
Clock down to lock the screws into place.
MAINTENANCE & CARE
•
Extreme temperatures, vibrations, and shock should
be avoided to prevent damage to the unit.
Clean display and unit with a soft, damp cloth. Do
not use solvents or scouring agents-they may mark
and damage the display and casing.
Problem: Hour is incorrect
(minute and date are correct).
Solution:
1. Be sure correct time zone and daylight saving time
are selected.
•
•
•
Do not submerge in water.
Immediately remove all low powered batteries to avoid
leakage and damage. Replace with new batteries
only, and of recommended size.
Note: For any questions not answered, contact La
Crosse Technology with the contact information found at
the end of this instructional manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
P.10
P.11
GB
GB
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this
product against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid
only on products purchased and used in North America and only to
the original purchaser of this product. To receive warranty service,
the purchaser must contact La Crosse Technology, Ltd for problem
determination and service procedures. Warranty service can only be
performed by a La Crosse Technology, Ltd authorized service center.
The original dated bill of sale must be presented upon request as
proof of purchase to La Crosse Technology, Ltd or La Crosse
Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our
option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the
limited warranty period specified above. All replaced parts and
products become the property of La Crosse Technology, Ltd and
must be returned to La Crosse Technology, Ltd. Replacement parts
and products assume the remaining original warranty, or ninety (90)
days, whichever is longer. La Crosse Technology, Ltd will pay all
expenses for labor and materials for all repairs covered by this
warranty. If necessary repairs are not covered by this warranty, or if
a product is examined which is not in need or repair, you will be
charged for the repairs or examination. The owner must pay any
shipping charges incurred in getting your La Crosse Technology, Ltd
product to a La Crosse Technology, Ltd authorized service center.
La Crosse Technology, Ltd will pay ground return shipping charges to
the owner of the product to a USA address only.
Your La Crosse Technology, Ltd warranty covers all defects in
material and workmanship with the following specified exceptions: (1)
damage caused by accident, unreasonable use or neglect (including
the lack of reasonable and necessary maintenance); (2) damage
occurring during shipment (claims must be presented to the carrier);
(3) damage to, or deterioration of, any accessory or decorative
surface; (4) damage resulting from failure to follow instructions
contained in your owner’s manual; (5) damage resulting from the
performance of repairs or alterations by someone other than an
authorized La Crosse Technology, Ltd authorized service center; (6)
units used for other than home use (7) applications and uses that this
product was not intended or (8) the products inability to receive a
signal due to any source of interference.. This warranty covers only
actual defects within the product itself, and does not cover the cost of
installation or removal from a fixed installation, normal set-up or
1
Download from Www.Somanuals.com. All Manuals Search And Download.
adjustments, claims based on misrepresentation by the seller or
performance variations resulting from installation-related
circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY
FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO
BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC
INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have
other rights specific to your State. Some States do no allow the
exclusion of consequential or incidental damages therefore the above
exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2809 Losey Blvd S.
La Crosse, WI 54601
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
La Crosse Technology
Made in China
All rights reserved. This handbook must not be reproduced in any
form, even in excerpts, or duplicated or processed using electronic,
mechanical or chemical procedures without written permission of the
publisher.
This handbook may contain mistakes and printing errors. The
information in this handbook is regularly checked and corrections
made in the next issue. We accept no liability for technical mistakes
or printing errors, or their consequences.
All trademarks and patents are acknowledged.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|