COLOR TV
SERVICE MANUAL
CHASSIS : MC-049A
MODEL:CT-29M65VE
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
the Schematic Diagram and Replacement Parts List.
in
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Before returning the receiver to the customer,
General Guidance
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc.,
to be sure the set is safe to operate without damage of
electrical shock.
An isolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
X-RAY Radiation
Warning:
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each exposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
The source of X-RAY RADIATION in this TV receiver is the
High Voltage Section and the Picture Tube.
For continued X-RAY RADIATION protection, the
replacement tube must be the same type tube as specified in
the Replacement Parts List.
To determine the presence of high voltage, use an accurate
high impedance HV meter.
Leakage Current Hot Check circuit
AC Volt-meter
Adjust brightness, color, contrast controls to minimum.
Measure the high voltage.
The meter reading should indicate
23.5 ¡ 1.5KV: 14-19 inch, 26 ¡ 1.5KV: 19-21 inch,
29.0 ¡ 1.5KV: 25-29 inch, 30.0 ¡ 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service
and correction is required to prevent the possibility of
premature component failure.
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
To Instrument's
exposed
0.15uF
METALLIC PARTS
1.5 Kohm/10W
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF CONTROLS
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
POWER
MUTE
Remote control handset
11
1
2
1
4
Before you use the remote control handset, please install the bat-
teries. See the next page.
2
5
8
0
3
6
1. POWER
9
7
switches the set on from standby or off to standby.
ARC
TV/AV
MENU
2. NUMBER BUTTONS
12
3
4
switches the set on from standby or directly select a number.
SOUND
PICTURE
13
3. ARC (Aspect Ratio Control)
OK
T
U
R
B
O
changes the picture format.
14
PR
PR
4. TURBO PICTURE / SOUND BUTTON
VOL
VOL
5
6
selects Turbo picture / sound.
REW
PLAY
STOP
FF
5. D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
REC
P/STILL
adjusts the volume.
adjusts menu settings.
7
8
I/II
SSM
SLEEP
LIST
15
PSM
PIP
EYE/
16
17
18
19
6. VCR BUTTONS (option)
9
control a LG video cassette recorder.
Q.VIEW
FAVOURITE
TEXT
7. SSM (Sound Status Memory)
recalls your preferred sound setting.
MIX
SIZE
?
M
TIME
STILL
PR
REVEAL
POSITION
MODE
9/4 PIP
10
8. I/II (option)
i
selects the language during dual language broadcast (option).
selects the sound output.
20
PR
SWAP
INPUT
9. PSM (Picture Status Memory)
recalls your preferred picture setting.
10. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
(With TELETEXT / PIP)
FAVOURITE Q.VIEW
TEXT
11. MUTE
switches the sound on or off.
10
12. TV/AV
MIX
SIZE
?
M
i
TIME
HOLD
REVEAL
UPDATE
MODE
INDEX
selects TV or AV mode.
switches the set on from standby.
13. MENU
selects a menu.
14. OK
(With TELETEXT / Without PIP)
accepts your selection or displays the current mode.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
15. LIST
displays the programme table.
16. EYE/ (option)
POWER
*
MUTE
switches the eye function on or off.
11
12
1
2
17. SLEEP
1
4
2
5
8
0
3
6
sets the sleep timer.
18. Q.VIEW
returns to the previously viewed programme.
9
7
ARC
TV/AV
MENU
19. FAVOURITE
3
4
selects a favorite programme.
SOUND
PICTURE
13
14
20. PIP BUTTONS (option)
OK
T
U
R
B
O
PIP
switches the sub picture on or off.
PR +/-
selects a programme for the sub picture.
SWAP
alternates between main and sub picture.
INPUT
selects the input mode for the sub picture.
PR
PR
VOL
VOL
5
6
REW
PLAY
STOP
FF
REC
P/STILL
SIZE
adjusts the sub picture size.
STILL
freezes motion of the sub picture.
POSITION
relocates the sub picture in clockwise direction.
9/4 PIP
7
8
I/II
SSM
SLEEP
LIST
15
PSM
EYE/
16
17
18
19
9
Q.VIEW
FAVOURITE
switches on or off the programme scan mode through 4 or 9
sub pictures.
COLOURED BUTTONS
These buttons are used for teletext (only TELETEXT models) or
programme edit.
(Without TELETEXT / PIP)
PIP
Q.VIEW
FAVOURITE
SIZE
POSITION
STILL
PR
9/4 PIP
20
PR
SWAP
INPUT
(Without TELETEXT / With PIP)
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
FScope
FTest Condition
This specification can be applied to all the television related to
MC-049A Chassis.
1) Temperature :20 ± 5°C(CST : 40 ± 5°C)
2) Relative Humidity:65 ± 10%
3) Use the parts only designated in B.O.M.,PARTS SPEC.,or
drawings.
4) Follow each drawing or spec for spec and performance of
parts,based upon P/N of B.O.M
5) Warm up TV set for more than 20min. before the
measurement.
Chassis
Market
Brand
LG
Standard input Voltage
110-240Vac, 50/60Hz
230Vac, 50/60Hz
MC049A Middle East, Africa
EU
FTest and Inspection Method
1) performance:Follow the Standard of LG TV test
2) Standards of Etc. requirement
- Safety: IEC60065
- EMC: EN55020,EN55013
FGeneral Specification
Item
No
Specification
PAL,SECAM BG
Remark
Receiving System
1
For EU/ For Non EU
PAL/SECAM DK
PAL-I/I
NTSC M
NTSC 4.43(AV)
SECAM-L/L’
OPTION
NTSC M/ PAL M/N
VHF : E2 ~ E12
UHF : E21 ~ E69
CATV : S1 ~ S20
HYPER : S21 ~ S41
AC 110-240V, 50/60Hz
AC 230V 50/60Hz
Available Channel
Input Voltage
2
3
Non EU
EU
Market
4
5
EU,CIS, China, Asia, Africa
Flat 25”, 29”, 28”, 32”
NOR 25”, 27”, 28”, 29”
FVS 100Program
Screen Size
Tuning System
6
7
200 PR. (W/O TXT)
Operating Environment
1) Temp : 0 ~ 45 deg
2) Humidity: 85% under
1) Temp : -20 ~ 60 deg
2) Humidity: 85% under
Storage Environment
8
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT INSTRUCTIONS
1. Application Object
4. Purity & Convergence adjustment
These instructions are applied to all of the color TV, MC-049A.
As preparatory operations before
CPT Assembling
assembling CPT, wind cotton Tape for
protecting to CPT NECK and DY, CPT
connection parts. At this moment, end
of tape should be over-lapped and
wound in direct route to the NECK.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.But the
adjustment can be changed by consideration of mass
production.
Fix the Magnet to the position as
shown picture below. Be careful not to
make CPT neck shadow while
adjusting DY.
Assembling DY to
CPT
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input AC voltage of the receiver must keep rating
voltage in adjusting.
HEAT RUN
Convergence Magnet
4
2
6Pole
Degaussing
STC Adjustment
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.
¢ ‚
¢‚
15 ~ 20mm
PURITY Adjustment
DY Fixing
Let the screen Standard condition.
Operate Heat-Run at least 15
minutes.
3. Focus adjustment
SCREEN Voltage adj.
3.1. Preliminary steps
Torque is to be 9-11 kg f.cm when
fixing DY.
Tune the TV set to receive a digital pattern.
(SVC mode:Automatically mode change the STANDARD
MODE)
W/B Fixing
FOCUS not yet ADJ.
3.2. Adjustment Method
STC not yet ADJ.
DYC not yet ADJ.
1) Single Focus CPT
Adjust the upper Focus volume of FBT for the best focus of
horizontal line A,vertical line B.
4.1. Color purity adjustment
2) Double Focus CPT
a) Adjust the lower Focus volume of FBT for the best focus
of vertical line B.
(1) It makes CPT or CABINET enough to demagnetization.
(2) Receive the signal of red raster.
b) Adjust the upper Focus volume of FBT for the best focus
of area A.
c) Repeat above step 1) and 2) for the best overall focus.
(3) Loosen fixed screw of DY and closely to CPT funnel part.
(4) Check the center of screen that PURITY MAGNET of CPT
by crossing adjustment. At this time, 4 & 6 pole magnet is
located to magnet of nothing.
(5) Move the DY to make equal red on whole screen and it
does not to make the DY by fixed screw after check a
simple color of Red/Green/Blue and white raster whether or
not it is a pollution of color.
(At this time, take care raster of screen and DY must fixing
in the condition which maintains a horizontality.)
(6) Check the TV set by move direction.
A
B
4.2. Convergence adjustment
These adjustments can the best condition of focus after
finished purity adjustment.
(1) Receive the signal of cross hatch that BACK RASTER is
black.
(2) Adjust brightness and luminosity till dot appear 9 ~12.
(3) Open angle of the two tab of 4 pole MAGNET by isogonic
angle and accord with vertical line of red and blue color in
the middle of screen.
<Fig 1. PAL Digital Pattern(EU05CH)>
(4) Maintain as angle of (3) and rotate the tab to accord with
vertical line of Red and Blue color in the middle of screen.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. White balance IIC Parameter
(5) Open angle of the two tab of 6 pole magnet by isogonic
angle and accord with vertical line of Red/Blue and Green.
(6) Maintain as angle of (5) and rotate the tab to accord with
horizontal line. In case of twisted horizontal line,repeat
adjustment of (3) ~ (5) remembering the movement of
Red/Green/Blue color.
Program TWBeng2.0
Program
TWBeng2.0 Speed Delay
Vcd Slave
24C16
Eprom_Slave
AE
1
30
R_Amp
R_Cut
B_Amp
B_Cut
(7) Move the DY to best condition of convergence and attach
the CPT to a rubber-chock for fixed DY.
Program
Sub Add
Start Bit
Stop Bit
Offset
TWBeng2.0 TWBeng2.0 TWBeng2.0 TWBeng2.0
1C8
12
1C3
12
4
1CA
12
1C5
12
4
5. Screen voltage adjustment
4
4
0
0
0
0
(1) Receive the PAL or SECAM(NTSC) signal into RF mode
regardless of channel.
Polarity
1
1
1
1
(2) If you press the “ADJ”button in LINE SVC mode(IN-START
button),the LINE SVC mode changes to screen adjustment
mode.
(3) Turn the Screen Volume of FBT to change luminance of
White signal center as shown below.
EP_Rom_S
7A7B
7475
7E7F
7879
Speed/ Plus
1
1
1
1
<CAUTION> W/B Program “Twbeng_v2.0”
- W/B adjustment after Cutoff
: Instart -> adj. -> mute(cutoff)-> tv/av(wb)
Release key is EXIT key
(4) Press the EXIT TV/AV button to exit SVC mode.
6. White balance adjustment
- W/B adjustment
: Instart -> mute(cpuoff) ->
Release key is TV/AV key
NOTE : When adjusting white balance automatically,connect the
adjustment JIG in SVC mode.(When pressing IN-
START,MUTE button on remote control for adjustment
orderly,it changes to SVC mode and screen displays
“CUT OFF”.)
7.Deflection setting Data Adjustment
(1) Receive 100% white pattern.
(2) Adjust LOW LIght status(4.5FL) of CUT R,CUT B at
CG:70.
(3) Adjust HIGH LIght status(35FL) of WDR R,WDR B at
WDR G:380.
(4) Repeat above step (2) and (3) for the best condition each
status of High Light and Low Light.
7.1 Adjustment preparation
(1) Tune the TV set to receive an Digital pattern(EU05CH).
(2) Deflection setting data adjustment is operate by SVC
communicator.
(3) Enter the deflection mode by selection SERVICE1 key on
SERVICE MENU after enter the adjustment mode by
pressing LINE SVC MODE(IN-START KEY).
(4) Enter the deflection mode by pressing ADJUST key.
(5) Use the CH D,E key to select adjustment item.
(6) Use the VOL F,Gkey to increase/decrease data.
<Table 1> White Balance Color analyzer
EU
N-EU
Menu
X
288
295
268
273
<Note>
Y
(1) When adjusting a deflection,adjust N50Hz of PAL signal first and
adjust a deflection at Normal 60Hz(NTSC).
(2) Adjust a deflection as shown below.
PAL 4:3 -> NTSC 4:3
o
o
Color Temperature
9000 K
13000 K
<Table 2> White Balance Initial Data
(3) After finishing deflection adjustment,press the EXIT key to
exit in adjustment mode.
Menu
Range
DATA
(4) Wide Models
LOW LIGHT
HIGH LIGHT
CR
CG
CB
0 ~ 511
0 ~ 511
0 ~ 511
0 ~ 511
0 ~ 511
0 ~ 511
70
70
After adjusting 16:9(50Hz), Readjust 14:9(50Hz) ->
ZOOM(50Hz) -> 4:3(50Hz) -> 16:9(60Hz) -> 14:9(60Hz) ->
ZOOM(60Hz) -> 4:3(60Hz).
70
WR
WG
WB
430
380
430
7.2 Adjustment
(1) VL(Vertical Linearity) adjustment:
Adjust the top & bottom size of inner circle to be equal.
(2) VA (Vertical Amplitude) adjustment:
<Table 3> White Balance Initial Data
1. IC
Adjust so that the circle of a digital circle pattern should be
located interval of 6~7mm from the effective screen of the
CPT.
Name
Maker
Algorithm
VCD IC VCT48xyi Micronas
EP_ROM 24C16 ST, ATMEL
(3) SC (Vertical S correction) adjustment:
Adjust so that all distance between each lattice width of
top/center/bottom are to be the same.
0
F
0
0
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
N60Hz(NTSC)
29”
N50Hz(PAL)
29”
Menu
Variable range
VS
VA
10
70
-70
140
130
-69
-15
-78
0
-512~511
-512~511
-512~511
-512~511
32~2047
-256~255
-512~511
-512~511
-512~511
-512~511
-512~511
-512~511
0~40
4
80
-70
140
110
-70
-12
-80
0
VL
SC
HS
EW
ET
<Fig. 2>PAL Digital pattern (EU05CH)
(4) VS (Vertical Shift) adjustment:
Adjust so that the geometric vertical center line is in accord
with vertical center line of CPT.
(5) HS(Horizontal Shift) adjustment:
Adjust so that the geometric horizontal center line is in
accord with horizontal center line of CPT.
(6) EW(East-West Width) adjustment:
EP
ANGLE
BOW
UPCOR
LOCOR
PIP_H
0
0
8
8
20
15
20
15
Adjust until the outmost left and right lattice of received
pattern is accord with 25% of other lattice width.
(7) ET(Trapezoidal) adjustment:
8.OPTION Adjustment
Adjust to make the length of top horizontal line same with it
of the bottom horizontal line.
(8) EP(Pin Cushion) adjustment:
Adjust so that middle portion of the outermost left and right
vertical line look like parallel with vertical lines of the CPT.
(9) ANGLE adjustment
8-1. Preparation for Adjustment
1) This option adjustment decides function in accordance with
model. Press the SVC TX adjustment button(IN-START
button) at SVC mode, then adjust the option at OPTION1
mode.
2) Mark the option adjustment data like [111,111,111,111] in
BOM.
When you adjust the angle, adjust correctly raster of
left/right screen.
(10) BOW adjustment
8-2. Adjustment Method
A standard is not changing the default value.
(11) CRNU(Upper Corner Correction) adjustment:
After finished EP adjustment,adjust vertical line of left-
top,right-top of screen to the best straight line.
(12) CRNL(Lower Corner Correction) adjustment:
After finished EP adjustment,adjust vertical line of left-
bottom ,right-bottom of screen to the best straight line.
(13) PIP(PIP Position)
OPTION data input
1) Function : 1, No function : 0
2) Select each OPTION function by the CH Up/Down
button and then set up each OPTION by the VOL
Up/Down button at OPTION 1,2,3,4.
8-3. OPTION Function
Adjust until the distance between PIP and main picture
becomes about 1~2mm by using VOL +/- key.
Option
Code
Function
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Without A/V3
With AV3
AV3
With out S-VIDEO
With S-VIDEO
S-VIDEO
DVD
Without COMPONENT(480i)
With COMPONENT(480i)
PHONE JACK
SCART
WIDE
SCART JACK
Not WIDE MODEL
WIDE MODEL
Without GAME function
With GAME function
Not 21inch MODEL
21inch MODEL
GAME
21inch
A2ST
<Fig. 3> PIP H Position
NICAM
NICAM & FM STEREO
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8-4. OPTION2 Function
Option
Code
Function
Without TURBO SEARCH
With TURBO SEARCH
100 PROGRAM SAVE
200 PROGRAM SAVE
Without EYE
TSEARCH
0
1
0
1
0
1
0
1
0
1
0
1
200PR
EYE
With EYE
TX019
8KEY
4KEY
8KEY
4KEY
8-5. OPTION3 Function
Option
Code
Function
REMARK
SYSTEM
0
1
0
1
0
1
0
1
0
1
ACMS
TOP
Without ACMS Function
With ACMS Function
FLOT TXT
TOP TXT
CH+AU
HDEV
Without D/K CHINA or BB SYSTEM
With D/K CHINA or BB SYSTEM
China, Australia
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
RF- STEREO
Selected correct system
In menu
OK
NO
Check the waveform
IF 1 of TU101
Check / Replace
TU 101
OK
NO
NO
Check the waveform
At pin 4, 5 of IC11
Check The Voltage
At pin 2, 19, 20, 21, 24 of IIC11
Check The voltage
At pin of IC821, IC822, Q807
OK
NO
Check the waveform
At pin 2, 4 of IC601
OK
Check / Replace
C821, IC822, Q807
NO
Check the Voltage
At pin 6 of IC601
Check / Replace Q601
OK
Check the waveform
At pin 8, 9, 11, 12 of IC601
OK
NO
Check the Voltage
At pin 5, 6 of IC602
Check / Replace
F806, D828(D805)
No Raster / Sound OK
Check the
Heater voltage of CPT
(6 ~ 6.5Vrms)
OK
NO
Check
Check the
Check
HV, Screen Voltage of
CPT
Heater pulse of FBT
T402
R, G, B out of
CPT Board
OK
NO
NO
NO
OK
Check 200V line of
CPT Board
& if no problem
check and Replace
Check
FR901, P402A
P402B, FR 401
Check
FBT T402
Check
IC901, P903A
Check
FBT T402
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
NO RASTER
Normal
CHECK B+
At D829 cathode
Abnormal
Open
Is the voltage at
each pin voltage of IC11
Check
Fuse of AC line
No
Check the
Yes
Check / Replace
Fuse
Ok
In/out of
regulator
No
Check pin 60
Of IC11(H - Out)
Check the Voltage
Of C803
No
(IC821, IC822
IC823, IC824
IC825)
Check &
Replace
IC11
Ok
140 ~ 310V
Yes
Check / Replace
DB801
Check Q402
Collector waveform
Check the Voltage
Pin 4 of IC801
No
No
Check &
Replace
Q402
Ok
18 ~ 20V
Yes
Check / Replace
Fuse IC801
Check / Replace
IC801, IC802, IC826
Check T401
& each pin voltage
No
No
Yes
Check &
Replace
T401
Check Fuse and Rectifition Diode of
secondary Load of SMPS trans(T803)
Check Q401
Collector waveform
No
Ok
Check / Replace
IC11
Check &
Replace
Q401
Yes
Check & Replace
T402
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
No Picture / No Sound
Is any OSD displayed?
OK
No
OK
OK
Check receiving system in MENU
& execute Auto - Program.
Check IC11 pin71,72,73
(R,G,B out)
Does the auto - Program
Operate properly.
No
OK
Store on manual - program MENU
No
Go to
No Sound /
Picture OK
No
Check SMPS Trans
Secondary Voltage
Check 1.8V, 3.3V,
5V DC Voltage
Check pin40(V out 1)
1Vp-p
OK
No
No
Check IC13
(Reset IC)
Check pin18
Reset Voltage
OK
3.3V DC
Check IC12(EEPROM)
& SCL, SDA, Line
Check pin57, 58
SCL, SDA
No
OK
3.3V swing
Relace IC11
Check / Replace
CPT Board component
Q501, Q503, Q504
(R, G, B out of IC11)
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
AV Stereo
Select correct system
In menu
OK
OK
Check the connection
Of AV equipment
NO
Check the the waveform
At pin16, 17 of IC11
AV
Check TU101 Tuner
OK
OK
NO
Check the voltage
Of pin2, 19, 20, 21,24 of IC11
Check the waveform
At pin4, 5, of IC11
OK
NO
Check the signal line of
SPK-L,R
Check waveform
At pin 2, 4 of IC601
OK
NO
Check pin 55 (mute)
of IC11
Check the voltage
At pin6 of IC601
OK
NO
NO
Check the vpltage
At pin7, 5 of IC601
Check /Replace
D828, D805, F806
Check the waveform
At pin 8, 9, 11, 12 of IC601
OK
NO
Check the connection of
side or Front AV Board
P603A
Connect the Board
OK
Replace IC601
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED CIRCUIT BOARD
MAIN
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE A/V
CONTROL
POWER
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOCK DIAGRAM
V 3 . 3 - T S
V 8 . 1 - T S
V 8
V 3 . 3
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED VIEW
913
150
153
943
400
170
112
174
520
120
310
501
550
540
600
320
601
330
300
700
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The components identified by mark
critical for safety.
is
Replace only with part number specified.
EXPLODED VIEW PARTS LIST
LOCA. No.
PART No.
DESCRIPTIONS
112
120
150
153
170
174
300
310
320
330
400
501
520
540
550
600
601
700
913
943
2426VSF0013
120-C77G
CPT SET, 29” SF A68KYN690X000MYB BARE (L,N,M,K,P)
SPEAKER,FULLRANGE C122P02K1459 8 OHM 10/15W 130 57*117
COIL,DEGAUSSING 29 FLAT (W) SELLA TECH 15 OHM 58T/0.55
DY(DEFLECTION YOKE) DC29SLSF1
6140VC2001R
6150Z-1040B
170-844J
CPT EARTH, 29” 96T 2LUG 2P HUG
6410VEH001E
3091V00277S
5020V00428C
320-062E
POWER CORD, 174-009Q VDE/SEMKO 2410MM 300 BLACK
CABINET ASSEMBLY, CT-29M65VE(SY-SET) MC049A #117A SPRAY
BUTTON, CONTROL CT-29M65VE ABS, HF-380 6KEY #117A SPRAY”
SPRING, KNOB
5020V00421C
3809V00205E
3210V00043J
6871VMMT20D
6871VSMJ43A
6871VSMJ32C
6871VSMJ30C
4810V00254E
0IGL120104A
332-229G
BUTTON, POWER CT-29M65VE ABS, HF-380 1KEY #117A SPRAY
BACK COVER ASSEMBLY, CT-29M66T 2PHONE MC007A
FRAME, CHASSIS HIPS 407AF CT-25Q4 MC-022A
PWB(PCB) ASSEMBLY,MAIN MC049A CT-29M65VE.LLLLSM8
PWB(PCB) ASSEMBLY,SUB POWER MC-049A M60 LGESY
PWB(PCB) ASSEMBLY,SUB CTL MC-049A M60 LGESY
PWB(PCB) ASSEMBLY,SUB A/V MC-049A M60 LGESY
BRACKET, SIDE AV CT-29M65VE(AV3) MC049A ABS, HF-380 #117A
IC,LG SEMICONDUCTOR CDS SENSOR MODULE(P1201-04)
SCREW,DRAWING HEXAGON D22 L40
1PTF0403116
SCREW TAP TITE(P),TRUSS HEAD + D4.0 L16.0 MSWR3/FZB
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
0DRTW00164A
0DD414809ED
0DD414809ED
0DD414809ED
0DD414809ED
0DD414809ED
0DD414809ED
0DD414809ED
0DD414809ED
0DD100009AM
0DD100009AM
0DD100009AM
0DD060009AC
0DRTW00164A
0DD414809ED
RGP10J TP52 DO41 .V 1A 30A .SEC 5UA
1N4148 TP
D407
D408
D501
D502
D503
D601
D602
D603
D604
D801
D802
D803
D815
D821
D823
D827
D828
D829
D830
D854
D901
D902
D903
D904
DB801
LD1101
Q401
ZD10
ZD122
ZD401
ZD402
ZD501
ZD601
ZD801
ZD803
ZD910
ZD911
ZD912
IC
0IPMGPH002A
0IZZVA1001D
TDA4863A 7P SOT524-1
VCT3804F DIP 64P DIP VCTI49XY
I7
1N4148 TP
IC11
1N4148 TP
0IMCRMN026A VCT4973F MICRONAS 88P PSSDIP
0IMMRSG036C M24C16-WBN6 8PIN PDIP ST 16M
IC11
1N4148 TP
IC12
1N4148 TP
0IFA752700A
0IKE455800E
0IPMGSA021C
0IPMGSK015B
0ILI817000G
KA75270Z 3 TP RE-SET IC MC-007
KIA4558 8DIP DUAL OP AMP
IC13
1N4148 TP
IC302
IC601
IC801
IC802
IC821
IC822
IC824
IC825
IC826
IC853
IC901
1N4148 TP
LA42152 13P ST 15W 2CH AUDIO AMP
STR-X6756 7PIN TO3PF-7L ST PWR IC
LTV817M-VB 4P,DIP BK
1N4148 TP
EU1ZV(1) TP SANKEN
EU1ZV(1) TP SANKEN
EU1ZV(1) TP SANKEN
TVR06J TP - 600V 250NSEC
RGP10J TP52 DO41 .V 1A 30A .SEC 5UA
1N4148 TP
0IMCRKE019A
0IMCRKE018A
0IMCRKE020A
0IMCRAU003A
0ISK120000A
0IMCRAU004A
0IPH610700B
KIA78R33API KEC 4P TO220 ST 3.3V 1A
KIA78R05API KEC 4P TO220 ST 5V 1A
KIA78S06P KEC 3P TO-92 TP 6V 0.15A
S1117-18PIC AUK KOREA 3P TO220F ST 1.8V 1A
SE120N 3P 120V ERROR AMP
0DRTW00141A SFAF504G ST ITO220 200V 5A .A .SEC 10UA
0DRTW00141A SFAF504G ST ITO220 200V 5A .A .SEC 10UA
S1117-33PIC AUK KOREA 3P TO220F ST 3.3V 1A
TDA6107JF/N3 9P ST RGB AMP
0DD410000AD
0DRTW00164A RGP10J TP52 DO41 .V 1A 30A .SEC 5UA
RU4AM,LF-L1 SANKEN SANKEN
TRANSISTOR
0DD060009AC
0DR210009AC
0DR210009AC
0DR210009AC
0DR140049AC
TVR06J TP - 600V 250NSEC
0TR319709AB
0TR198009BA
0TR127409AB
0TR205900AB
0TRSA10001C
0TR437000BA
0TR198009BA
0TR198009BA
0TR198009BA
0TR198009BA
0TR534309AA
0TR198009BA
0TR534309AA
0TR198009BA
0TR421009CB
0TR534309AA
0TR102009AB
0TR102009AB
0TR534309AA
0TR127409AB
0TR102009AB
Q104
Q301
Q303
Q401
Q401
Q402
Q501
Q502
Q503
Q504
Q505
Q507
Q510
Q601
Q801
Q802
Q803
Q804
Q805
Q807
Q808
KTC3197,TP(KTC388A),KEC
2SA1980Y TP AUK
BAV21 TP DO35 200V 0.2A 1A 50SEC 100A
BAV21 TP DO35 200V 0.2A 1A 50SEC 100A
BAV21 TP DO35 200V 0.2A 1A 50SEC 100A
1N4004A T-81 TP DO41 500V 1.0A 30A - 10UA
KTA1274-Y TO-92L TP KEC
KTD2059-Y TO-220IS KEC
2SD2689LS SANYO ST TO220F 1500V 10A
KTC4370A-Y TO-220IS KEC
2SA1980Y TP AUK
0DRTW00131C TS6P05G ST TSOP-6 600V 6A .A .SEC .A
0DD000000BA
0DSFC00011A
0DZ910009BD
0DZ330009DG
0DZ510009BF
0DZ110009AD
0DZ110009AD
0DZ820009AH
0DZ620009AH
0DZ510009BF
0DZ510009BF
0DZ510009BF
0DZ510009BF
SA5711-B(DL-1LO(S)) BK AMBER
FFPF60B150DS ST TO220F 600V 20A 120A
GDZJ9.1B TP DO34 0.5W 9.1V
2SA1980Y TP AUK
2SA1980Y TP AUK
GDZJ33B TP DO34 0.5W 33.0V
2SA1980Y TP AUK
GDZ5.1B TP DO34 0.5W 5.1V 0.02A
MTZJ11B TP ROHM-K DO34 - 11V 5UA
MTZJ11B TP ROHM-K DO34 - 11V 5UA
MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA
MTZJ6.2A TP ROHM-K DO34 0.5W 6.2V 150UA
GDZ5.1B TP DO34 0.5W 5.1V 0.02A
GDZ5.1B TP DO34 0.5W 5.1V 0.02A
GDZ5.1B TP DO34 0.5W 5.1V 0.02A
GDZ5.1B TP DO34 0.5W 5.1V 0.02A
2SC5343Y TP AUK
2SA1980Y TP AUK
2SC5343Y TP AUK
2SA1980Y TP AUK
BF421L(AMMO)TO-92 TP PHILIPS
2SC5343Y TP AUK
KRC102M(KRC1202) KEC TP
KRC102M(KRC1202) KEC TP
2SC5343Y TP AUK
CAPACITOR
KTA1274-Y TO-92L TP KEC
KRC102M(KRC1202) KEC TP
C10
C101
C104
C106
C107
C108
C109
C11
0CX2200K409
0CQ2721N409
0CN1030F679
0CN1030F679
0CN1030F679
0CN1030F679
0CN1030F679
0CX2200K409
0CN1030F679
22P 50V J SL TA52
0.0027UF D 100V 5% PE TP5
10000P 16V M Y TA52
10000P 16V M Y TA52
10000P 16V M Y TA52
10000P 16V M Y TA52
10000P 16V M Y TA52
22P 50V J SL TA52
DIODE
0DD400509AA
0DD414809ED
0DRTW00164B
0DRTW00164A
0DRTW00164B
0DRTW00164B
D301
D302
D403
D404
D405
D406
1N4005 TP KEC
1N4148 TP
RGP15J TP52 DO15 .V 1.5A 50A 250NSEC
RGP10J TP52 DO41 .V 1A 30A .SEC 5UA
RGP15J TP52 DO15 .V 1.5A 50A 250NSEC
RGP15J TP52 DO15 .V 1.5A 50A 250NSEC
C110
10000P 16V M Y TA52
-22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For Capacitor & Resistors,
the charactors at 2nd and 3rd
digit in the P/No. means as
follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
0CE107DD618
0CE227DD618
0CE107DD618
0CE106DF618
0CN2210K519
0CN2210K519
0CE475DK618
0CN1040K949
0CN1040K949
0CN1040K949
0CN3310K519
0CE226DF618
0CE226DF618
0CN1040K949
0CE226DD618
0CE105DK618
0CQ1041N409
0CE107DJ618
0CQ3331N509
0CE476DK618
0CN4710K519
0CQ1031N509
0CE475DK618
0CQ1521N509
181-015Q
100UF STD 10V M FL TP5
220UF STD 10V M FL TP5
100UF STD 10V M FL TP5
10UF STD 16V M FL TP5
220P 50V K B TA52
C513
C514
C517
C519
C520
C521
C522
C524
C526
C527
C528
C529
C530
C532
C533
C534
C535
C536
C537
C538
C540
C541
C542
C543
C545
C547
C548
C602
C603
C604
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C617
C618
C619
C620
C624
C625
C626
C627
C631
C632
0CN1040K949
0CE107DD618
0CN1040K949
0CN1010K519
0CE107DD618
0CN1040K949
0CN1040K949
0CE107DD618
0CN1040K949
0CN1040K949
0CN1040K949
0CN1040K949
0CN1010K519
0CN1040K949
0CE107DD618
0CN1040K949
0CN1040K949
0CN1040K949
0CN1040K949
0CN1040K949
0CE107DD618
0CE107DD618
0CE107DD618
0CE107DD618
0CK1010K515
0CN2710K519
0CN1040K949
0CE108DH618
0CE475DK618
0CQ2731N509
0CE476DF618
181-007C
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
C1101
C111
C12
0.1UF D 50V 80%,-20% F(Y5V) TA52
100P 50V K B TA52
C1208
C1240
C1241
C126
C13
100UF STD 10V M FL TP5
220P 50V K B TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
4.7UF STD 50V 20% FL TP 5
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
330P 50V K B TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
100P 50V K B TA52
C17
C18
C19
22UF STD 16V M FL TP5
22UF STD 16V M FL TP5
0.1UF D 50V 80%,-20% F(Y5V) TA52
22UF STD 10V 20% FL TP 5
1UF STD 50V M FL TP5
C216
C217
C23
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
C24
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
C25
0.1000UF 100V J PE TP
C303
C304
C306
C308
C309
C310
C402
C403
C404
C405
C406
C407
C409
C410
C411
C413
C414
C415
C416
C417
C419
C420
C421
C422
C501
C502
C503
C504
C505
C506
C507
C508
C509
C510
C511
C512
100UF STD 35V M FL TP5
0.033UF D 100V 10% PE TP5
47UF STD 50V M FL TP5
470P 50V K B TA52
0.01UF D 100V 10% PE TP5
4.7UF STD 50V 20% FL TP 5
0.0015UF D 100V 10% PE TP5
0.02UF 1.6KV H M/PP NI FM20
DEHR33D471KN3A 470PF 2KV 10%
PP 400V 0.039UF K
100UF STD 10V M FL TP5
100UF STD 10V M FL TP5
100UF STD 10V M FL TP5
100P 50V K B
TS
181-091G
270P 50V K B TA52
181-010H
0.1UF D 50V 80%,-20% F(Y5V) TA52
1000UF STD 25V M FL TP5
4.7UF STD 50V 20% FL TP 5
0.027UF D 100V 10% PE TP5
47UF STD 16V M FL TP5
0CE475DK618
0CK2220W515
0CE105CR636
181-038K
4.7UF STD 50V 20% FL TP 5
2200P 500V K B
TS
1UF SHL,SD 250V 20% BP(D) TP FM5
0.56UF D 250V J M/PP FM20
100UF STD 35V M FL TP5
0CE107DJ618
0CK2710W515
0CE108DH618
181-009R
MPE ECQ-V1H104JL3(TR), 50V 0.1UF
10UF STD 16V M FL TP5
270P 500V K B
TS
0CE106DF618
0CE106DF618
0CQ2731N509
0CE475DK618
0CE476DH618
181-007C
1000UF STD 25V M FL TP5
PP 200V 0.022UF K
10UF STD 16V M FL TP5
0.027UF D 100V 10% PE TP5
4.7UF STD 50V 20% FL TP 5
47UF STD 25V 20% FL TP 5
MPE ECQ-V1H104JL3(TR), 50V 0.1UF
MPE ECQ-V1H104JL3(TR), 50V 0.1UF
MPE ECQ-V1H104JL3(TR), 50V 0.1UF
0.1UF D 50V 80%,-20% F(Y5V) TA52
47UF STD 10V 20% FL TP 5
0.1UF D 50V 80%,-20% F(Y5V) TA52
100P 50V K B TA52
0CK2710W515
0CE108DH618
181-009C
270P 500V K B
TS
1000UF STD 25V M FL TP5
PP 200V 0.056UF J
0CK2710W515
0CE475DR618
0CQ6831N509
0CQ6831N509
0CQ3331N509
0CN1040K949
0CN2710K519
0CN2710K519
0CN1040K949
0CE107DD618
0CN1040K949
0CE475DK618
0CN1040K949
0CE107DD618
270P 500V K B
TS
181-007C
4.7UF STD 250V 20% FL TP 5
0.068UF D 100V 10% PE TP5
0.068UF D 100V 10% PE TP5
0.033UF D 100V 10% PE TP5
0.1UF D 50V 80%,-20% F(Y5V) TA52
270P 50V K B TA52
181-007C
0CN1040K949
0CE476DD618
0CN1040K949
0CN1010K519
0CE106DK618
0CN1010K519
0CF3341L438
0CF3341L438
0CF3341L438
0CK1030K945
0CF3341L438
0CF3341L438
10UF STD 50V M FL TP5
270P 50V K B TA52
100P 50V K B TA52
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
0.33UF D 63V 5% TP 5 M/PE NI
0.33UF D 63V 5% TP 5 M/PE NI
0.33UF D 63V 5% TP 5 M/PE NI
0.01UF 50V Z F TR
0.1UF D 50V 80%,-20% F(Y5V) TA52
4.7UF STD 50V 20% FL TP 5
0.1UF D 50V 80%,-20% F(Y5V) TA52
100UF STD 10V M FL TP5
0.33UF D 63V 5% TP 5 M/PE NI
0.33UF D 63V 5% TP 5 M/PE NI
-23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For Capacitor & Resistors,
the charactors at 2nd and 3rd
digit in the P/No. means as
follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
0CF3341L438
0CQZVBK002A
0CE337KV6A0
0CK10201515
0CK10201515
0CE105DK618
0CE336DK618
181-014Y
0.33UF D 63V 5% TP 5 M/PE NI
A.C 275V 0.1UF M (S=15)
330UF SLT 450V 20% VNSN BULK
1000P 1KV K B TS
L503
L504
L505
L506
L507
L508
L509
L801
T401
T803
0LA0101K119
0LA0101K119
0LA0101K119
0LA0101K119
0LA0101K119
0LA0101K119
0LA0152K119
150-C02F
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,15UH K 2.3*3.4 TP
COIL,CHOKE 82UH PHY TURN
TRANSFORMER,H-DRIVE,EI-19,BULK
C636
C802
C803
C804
C806
C809
C810
C811
C813
C815
C817
C819
C820
C821
C822
C823
C824
C825
C826
C827
C828
C829
C830
C831
C833
C834
C835
C837
C838
C839
C840
C843
C845
C846
C868
C901
C902
C903
C904
1000P 1KV K B TS
1UF STD 50V M FL TP5
33UF STD 50V M FL TP5
MPP 1.6KV 0.0015UF J
0CK4710W515
0CK8210K515
0CK1040K945
0CK1520K515
0CN1040K949
181-091C
470PF 500V K B TR
151-C02F
820P 50V K B TS
6170VMCC01P TRANSFORMER,EER5345 300UH B+120V
0.1UF 50V Z F TR
CONNECTOR
1500P 50V K B TS
0.1UF D 50V 80%,-20% F(Y5V) TA52
DEHR33A471KN2A 470PF 1KV 10%,-10%
470UF STD 25V M FL TP5
470UF STD 10V M FL TP5
1000UF STD 10V M FL TP5
4700P 1KV K B S
387-A05J
387-A06J
387-A04D
5P 2.5MM 500MM H-B UL1007AWG26
6P 2.5MM 500MM H-B UL1007AWG26
4P 2.5MM 250MM H-B UL1007AWG26
P07B
P08B
0CE477DH618
0CE477DD618
0CE108DD618
0CK47201510
0CE108DD618
0CE108DD618
0CE477DD618
0CE335CK636
0CE108DH618
0CE227DP61A
0CE107CP618
181-091Y
PA01B
RESISTOR
0RP0050H709
0RP0050H709
0RP0020J809
0RP0020J809
0RP0050H709
0RP0050H709
0RP0050H709
0RP0050H709
0RF0121K607
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD7501F609
0RD7502F609
0RD0562F609
0RD1000F609
0RD8200F609
0RD0682F609
0RD1501F609
0RD3000F609
0RD3300F609
0RD3900F609
0RD2200F609
0RD3000F609
0RD3300F609
0RD4300F609
0RD0752F609
0RD2200A609
0.05 OHM 1/2 W 10% TA52
0.05 OHM 1/2 W 10% TA52
0.02 OHM 1 W 20% TA52
0.02 OHM 1 W 20% TA52
0.05 OHM 1/2 W 10% TA52
0.05 OHM 1/2 W 10% TA52
0.05 OHM 1/2 W 10% TA52
0.05 OHM 1/2 W 10% TA52
1.2 OHM 2 W 5.00% TA62
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
7.5K OHM 1/6 W 5.00% TA52
75K OHM 1/6 W 5.00% TA52
56 OHM 1/6 W 5.00% TA52
100 OHM 1/6 W 5% TA52
820 OHM 1/6 W 5.00% TA52
68 OHM 1/6 W 5.00% TA52
1.5K OHM 1/6 W 5% TA52
300 OHM 1/6 W 5.00% TA52
330 OHM 1/6 W 5.00% TA52
390 OHM 1/6 W 5% TA52
220 OHM 1/6 W 5.00% TA52
300 OHM 1/6 W 5.00% TA52
330 OHM 1/6 W 5.00% TA52
430 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
220 OHM 1/2 W(7.0) 5.00% TA52
F802
F804
F805
F806
FR402
FR403
FR404
FR405
FR901
J204
1000UF STD 10V M FL TP5
1000UF STD 10V M FL TP5
470UF STD 10V M FL TP5
3.3UF SHL,SD 50V 20% FM5 BP(D) TP
1000UF STD 25V M FL TP5
220UF STD 160V 20% FL TP 7.5
100U SHL 160V M FL TP5
R 680PF 2KV 10%,-10% R/TP TP7.5
470PF 500V K B TR
0CK4710W515
0CQ4731N509
0CE227DK618
0CE106DH618
0CE228BF618
181-120K
0.047UF D 100V 10% PE TP5
220UF STD 50V M FL TP5
10UF STD 25V M FL TP5
2200UF KME 16V M FL TP5
2200PF 4KV M E FMTW LEAD 4.5
100UF STD 10V M FL TP5
R 560PF 2KV 10%,-10% R/TP TP7.5
220UF STD 10V M FL TP5
4.7UF STD 250V 20% FL TP 5
0.1UF TE 250V 10% M/PE NI TP5
2KV B 122K TP7.5
J208
J211
J220
J222
J261
0CE107DD618
181-091X
J509
J510
0CE227DD618
0CE475DR618
0CQ1044R539
181-033S
J512
J566
R102
R105
R109
R11
0CE475DR618
4.7UF STD 250V 20% FL TP 5
COIL & INDUCTOR
R110
R111
0LA0102K139
0LA0101K119
0LA0101K119
0LA0102K119
0LA0102K119
0LA0472K119
0LA0472K119
150-717J
INDUCTOR,10UH K 4*10.5 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,10UH K 2.3*3.4 TP
INDUCTOR,10UH K 2.3*3.4 TP
INDUCTOR,47UH K 2.3*3.4 TP
INDUCTOR,47UH K 2.3*3.4 TP
COIL,CHOKE CHOKE 560UH (E/W)
COIL,LINEARITY 20UH 1PHY 1TURN 1
INDUCTOR,1.0UH K 2.3*3.4 TP
INDUCTOR,1.0UH K 2.3*3.4 TP
L101
L103
L12
R112
R113
R1143
R1146
R1147
R1148
R1149
R1150
R1201
R1230
L1203
L1204
L1243
L1244
L401
L402
L501
L502
150-L01D
0LA0101K119
0LA0101K119
-24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For Capacitor & Resistors,
the charactors at 2nd and 3rd
digit in the P/No. means as
follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
0RD2200A609
0RD2202F609
0RD2700A609
0RD1000F609
0RD1000F609
0RD0752F609
0RD0752F609
0RD0752F609
0RD0752F609
0RD0752F609
0RD0752F609
0RD1000F609
0RD1000F609
0RD2700F609
0RD1000F609
0RD1000F609
0RD3301F609
0RD1501A609
0RN3602F409
0RD2400A609
0RD0561A609
0RD1002F609
0RD1002F609
0RD3601F609
0RD4702F609
0RD3902F609
0RD2001F609
0RD3301F609
0RD4702F609
0RD4701F609
0RN0471H509
0RN0471H509
0RS2700K607
0RD1000F609
0RD2702F609
0RN2001F409
0RN8202F409
0RD3301F609
0RD1001F609
0RD0561A609
0RD1501F609
0RD2702F609
0RD4700F609
0RD2701A609
0RD1501A609
0RN4302F409
0RD1000F609
0RD1000F609
0RD1000F609
0RD1002F609
0RD2701A609
0RD5600A609
220 OHM 1/2 W(7.0) 5.00% TA52
22K OHM 1/6 W 5% TA52
270 OHM 1/2 W(7.0) 5.00% TA52
100 OHM 1/6 W 5% TA52
R404
R405
R408
R409
R410
R411
R412
R413
R414
R415
R416
R417
R42
0RD0332A609
0RS1500K690
0RS0221K619
0RD1801A609
33 OHM 1/2 W(7.0) 5.00% TA52
150 OHM 2 W 5% MF5.0
R1231
R124
R125
R126
R127
R201
R202
R209
R210
R211
R212
R24
2.2 OHM 2 W 5% TR
1.8K OHM 1/2 W(7.0) 5.00% TA52
100 OHM 1/6 W 5% TA52
0RMZVBK002D 15K OHM 5W +/-5% RSR V-TYPE
75 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
75 OHM 1/6 W 5.00% TA52
100 OHM 1/6 W 5% TA52
0RS5102H609
0RD7501A609
0RS2202H609
0RS1001H609
0RD1002F609
0RD6801F609
0RD8203F609
0RD4701F609
0RD3600F609
0RD1002F609
0RD0682F609
0RD3301F609
0RN6801F409
0RN6801F409
0RD6801F609
0RD1501F609
0RD2700F609
0RD1201F609
0RD3600F609
0RD3600F609
0RD3600F609
0RD0332F609
0RD0332F609
0RD0332F609
0RD1600F609
0RD1600F609
0RD1600F609
0RD0222F609
0RD2701F609
0RD1001F609
0RD3002F609
0RD0152F609
0RD2702F609
0RD1000F609
0RD1002F609
0RD4702F609
0RD2700F609
0RD8200F609
0RD9100F609
0RD4700F609
0RD3301F609
0RD3001F609
0RD0221A609
0RD0221A609
0RD0221A609
0RD0221A609
0RD1001F609
51K OHM 1/2 W 5.00% TA52
7.5K OHM 1/2 W(7.0) 5.00% TA52
22K OHM 1/2 W 5.00% TA52
1K OHM 1/2 W 5.00% TA52
10K OHM 1/6 W 5% TA52
6.8K OHM 1/6 W 5.00% TA52
820K OHM 1/6 W 5.00% TA52
4.7K OHM 1/6 W 5% TA52
360 OHM 1/6 W 5.00% TA52
10K OHM 1/6 W 5% TA52
68 OHM 1/6 W 5.00% TA52
3.3K OHM 1/6 W 5.00% TA52
6.8K OHM 1/6 W 1.00% TA52
6.8K OHM 1/6 W 1.00% TA52
6.8K OHM 1/6 W 5.00% TA52
1.5K OHM 1/6 W 5% TA52
270 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
R25
270 OHM 1/6 W 5% TA52
R26
R421
R422
R449
R501
R502
R503
R504
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R516
R517
R518
R519
R520
R521
R522
R527
R532
R539
R540
R541
R542
R543
R555
R557
R558
R601
R602
R603
R604
R605
100 OHM 1/6 W 5% TA52
R28
100 OHM 1/6 W 5% TA52
R29
3.3K OHM 1/6 W 5.00% TA52
1.5K OHM 1/2 W(7.0) 5.00% TA52
36K OHM 1/6 W 1.00% TA52
240 OHM 1/2 W(7.0) 5.00% TA52
5.6 OHM 1/2 W(7.0) 5.00% TA52
10K OHM 1/6 W 5% TA52
10K OHM 1/6 W 5% TA52
3.6K OHM 1/6 W 5.00% TA52
47K OHM 1/6 W 5% TA52
39K OHM 1/6 W 5.00% TA52
2K OHM 1/6 W 5% TA52
R30
R301
R302
R303
R304
R305
R306
R307
R308
R308
R309
R31
1.2K OHM 1/6 W 5% TA52
360 OHM 1/6 W 5.00% TA52
360 OHM 1/6 W 5.00% TA52
360 OHM 1/6 W 5.00% TA52
33 OHM 1/6 W 5.00% TA52
33 OHM 1/6 W 5.00% TA52
33 OHM 1/6 W 5.00% TA52
160 OHM 1/6 W 5.00% TA52
160 OHM 1/6 W 5.00% TA52
160 OHM 1/6 W 5.00% TA52
22 OHM 1/6 W 5.00% TA52
2.7K OHM 1/6 W 5% TA52
1K OHM 1/6 W 5% TA52
3.3K OHM 1/6 W 5.00% TA52
47K OHM 1/6 W 5% TA52
4.7K OHM 1/6 W 5% TA52
4.7 OHM 1/2 W 2.00% TA52
4.7 OHM 1/2 W 2.00% TA52
270 OHM 2 W 5.00% TA62
100 OHM 1/6 W 5% TA52
R310
R312
R313
R314
R315
R316
R317
R318
R319
R32
27K OHM 1/6 W 5.00% TA52
2K OHM 1/6 W 1.00% TA52
82K OHM 1/6 W 1.00% TA52
3.3K OHM 1/6 W 5.00% TA52
1K OHM 1/6 W 5% TA52
30K OHM 1/6 W 5.00% TA52
15 OHM 1/6 W 5.00% TA52
27K OHM 1/6 W 5.00% TA52
100 OHM 1/6 W 5% TA52
R320
R321
R322
R323
R324
R325
R326
R328
R33
5.6 OHM 1/2 W(7.0) 5.00% TA52
1.5K OHM 1/6 W 5% TA52
27K OHM 1/6 W 5.00% TA52
470 OHM 1/6 W 0.05 TA52
2.7K OHM 1/2 W(7.0) 5.00% TA52
1.5K OHM 1/2 W(7.0) 5.00% TA52
43K OHM 1/6 W 1.00% TA52
100 OHM 1/6 W 5% TA52
10K OHM 1/6 W 5% TA52
47K OHM 1/6 W 5% TA52
270 OHM 1/6 W 5% TA52
820 OHM 1/6 W 5.00% TA52
910 OHM 1/6 W 5.00% TA52
470 OHM 1/6 W 0.05 TA52
3.3K OHM 1/6 W 5.00% TA52
3K OHM 1/6 W 5.00% TA52
2.2 OHM 1/2 W(7.0) 5.00% TA52
2.2 OHM 1/2 W(7.0) 5.00% TA52
2.2 OHM 1/2 W(7.0) 5.00% TA52
2.2 OHM 1/2 W(7.0) 5.00% TA52
1K OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
R35
100 OHM 1/6 W 5% TA52
R37
10K OHM 1/6 W 5% TA52
2.7K OHM 1/2 W(7.0) 5.00% TA52
560 OHM 1/2 W(7.0) 0.05 TA52
R38
R401
R403
-25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For Capacitor & Resistors,
the charactors at 2nd and 3rd
digit in the P/No. means as
follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
LOCA. NO
PART NO
DESCRIPTION
LOCA. NO
PART NO
DESCRIPTION
3.3K OHM 1/6 W 5.00% TA52
10K OHM 1/6 W 5% TA52
1K OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
18K OHM 1/6 W 5.00% TA52
1K OHM 1/6 W 5% TA52
3.3K OHM 1/6 W 5.00% TA52
2.2 OHM 1/6 W 5.00% TA52
100 OHM 1/6 W 5% TA52
1K OHM 1/6 W 5% TA52
270 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
0.47M OHM 1/2 W 5% TA52
RWR 15W 1.0 OHM J PD
47K OHM 2 W 5% TR
1/2 W 1.5K,10%,PLIKOR(HIGH SURGE)
1/2 W 1.5K,10%,PLIKOR(HIGH SURGE)
1/2 W 1.5K,10%,PLIKOR(HIGH SURGE)
2.2M OHM 1/2 W(7.0) 5.00% TA52
220 OHM 1/6 W 5.00% TA52
R606
R607
R608
R609
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R620
R621
R622
R623
R624
R664
R802
R803
R804
R805
R806
R807
R808
R809
R814
R816
R817
R823
R825
R827
R828
R831
R838
R840
R841
R842
R843
R844
R845
R846
R847
R858
R901
R902
R903
R906
R907
R908
0RD3301F609
0RD1002F609
0RD1001F609
0RD1000F609
0RD1802F609
0RD1001F609
0RD3301F609
0RD0221F609
0RD1000F609
0RD1001F609
0RD2700F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RD1000F609
0RKZVTA001K
180-822M
R909
R910
R911
R912
R925
0RCZVTA002D
0RCZVTA002D
0RCZVTA002D
0RD2204A609
0RD2200F609
SWITCH
SW1101
SW1102
SW1103
SW1104
SW1105
SW1106
SWP801
140-315A
140-315A
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
SDKEA3 ALPS IEC 250V 8A HORIZONTAL 480G
140-315A
140-315A
140-315A
140-315A
6600VM2002A
SPARK GAP, AXAL
SG901
SG902
SG903
SG904
165-004A
165-004A
AG20PT 152F-L3N/S-23
AG20PT 152F-L3N/S-23
AG20PT 152F-L3N/S-23
WSP-122N 1200V -100V,+300V
165-004A
6918VAX002H
FILTER & CRYSTAL
0RS4702K619
0RS4702K619
180-A01P
FB1241
FB401
FB801
FB802
FB803
FB825
T801
125-123A
125-022K
FERRITE BFD3565R2F(TAPING)
47K OHM 2 W 5% TR
FERRITE AXIAL 62MM 1UH NY 3.5X6.0MM
FERRITE AXIAL 62MM 1UH NY 3.5X6.0MM
FERRITE AXIAL 62MM 1UH NY 3.5X6.0MM
FERRITE AXIAL 62MM 1UH NY 3.5X6.0MM
FERRITE AXIAL 62MM 1UH NY 3.5X6.0MM
LINE FILTER SQE2930 10MH
0.13 OHM 2 W 5% TA62 RWR
220 OHM 1/2 W(7.0) 5.00% TA52
1.5K OHM 1/6 W 5% TA52
1K OHM 1/6 W 5% TA52
8.2M OHM 1/2 W 5.00% TA52
1K OHM 1/6 W 5% TA52
15 OHM 1/6 W 5.00% TA52
4.7K OHM 1/6 W 5% TA52
4.7K OHM 1/6 W 5% TA52
1K OHM 1/6 W 5% TA52
1.5K OHM 1/6 W 5% TA52
2.2K OHM 1/6 W 5.00% TA52
4.7K OHM 1/6 W 5% TA52
1.6 OHM 2 W 5.00% TA62
1.6 OHM 2 W 5.00% TA62
10K OHM 1/6 W 5% TA52
330 OHM 1/2 W(7.0) 5.00% TA52
820 OHM 1/6 W 5.00% TA52
10K OHM 1/6 W 5% TA52
75K OHM 1/6 W 5.00% TA52
220K OHM 1/6 W 5.00% TA52
4.7K OHM 1/6 W 5% TA52
220 OHM 1/6 W 5.00% TA52
220 OHM 1/6 W 5.00% TA52
220 OHM 1/6 W 5.00% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
100 OHM 1/6 W 5% TA52
125-022K
0RD2200A609
0RD1501F609
0RD1001F609
0RK8204H609
0RD1001F609
0RD0152F609
0RD4701F609
0RD4701F609
0RD1001F609
0RD1501F609
0RD2201F609
0RD4701F609
0RF0161K607
0RF0161K607
0RD1002F609
0RD3300A609
0RD8200F609
0RD1002F609
0RD7502F609
0RD2203F609
0RD4701F609
0RD2200F609
0RD2200F609
0RD2200F609
0RD1000F609
0RD1000F609
0RD1000F609
125-022K
125-022K
125-022K
150-F06P
X11
6202VDB007B
6200QL3001Z
RESONATOR,HC49U 20.250MHZ 30PPM
B39361-X6966-D100 EPCOS ST
Z101
JACK
JK1201
JK1203
JK201
JK202
380-068D
UEJ-CV-003 UGCOM E/P
6613V00004B
6612VJH011K
6612VJH011L
3P
PPJ109K A/V I/O 6P STEREO FOR21PIN
PPJ109L A/V I/O 6P DVD IN Y-PB-PR ENG
ACCESSORIES
A1
A2
3828VA0464H
6710V00112S
MANUAL,OWNERS MC049A RUS/BZ03 LG RU/EN
REMOTE CONTROLLER,MC049A W/O PIP W/O TXT
MISCELLANEOUS
FP801
PA1101
SK901
T402
0FT4001B51C
FUSE, 4000MA 250 V 5.2X20
6712SCA228B
6620VBC003A
6174V-5013A
163-058D
REMOTE CONTROLLER RECEIVER,AT138BNN1S
SOCKET (CIRC),CPTPCS030A 8PIN 14/360
FBT,BSC28-N2351 29 YINYANG B+120V FBT
THERMISTOR,03-07MX 7 OHM 20% 80/60
TUNER,TAEW-G002D W/W ALL IN W/S 09Z VE
VARISTOR,TVR621D14A THINKING 620V 10%
TH801
TU101
VD1111
6700VS0002F
164-003G
-26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
P/NO: 3854VA0146A - S1
2004.4.16
Download from Www.Somanuals.com. All Manuals Search And Download.
SVC. SHEET : 3854VA0146A-S
Download from Www.Somanuals.com. All Manuals Search And Download.
Jun.,2004
P/NO : 3828VD0178U
Printed in Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
|