26LD320H 32LD320H 37LD320H 42LD320H
32LD325H 37LD325H
26LD340H 32LD340H 37LD340H 42LD340H
26LD345H 32LD345H 37LD345H 42LD345H
Lodging Guest Interactive Pro:Centric™ TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EXPERIENCED INSTALLER
Master TV Setup
pages 11 – 14
Cloning Information
pages 23 – 29
FTG Mode of Operation
pages 30 – 40
© Copyright 2011, LG Electronics U.S.A., Inc.
P/N: 206-4186 (Rev B)
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
17. Power Cord
Caution: It is recommended that appliances be placed
2. Keep these instructions.
3. Heed all warnings.
upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional
outlets or branch circuits. Check the specification page
in the Owner’s Manual to be certain.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as twisting, kinking, or pinching or being closed in a
door or walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the appliance.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Do not use a damaged or loose power cord. Be sure to grasp
the plug when unplugging the power cord. Do not pull on the
power cord to unplug the TV.
18. Overloading
Do not connect too many appliances to the same AC power
outlet as this could result in fire or electric shock. Do not
overload wall outlets. Overloaded wall outlets, loose or dam-
aged wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous. Any of
these conditions could result in fire or electric shock.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the
point where it exits from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
19. Outdoor Use/Wet Location
Warning: To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer or sold with the appara-
tus. When a cart is used, use caution when moving the
cart/apparatus combination in order to avoid injury from
tip-over.
Do not touch the TV with wet hands. Do not install this prod-
uct near flammable objects such as gasoline or candles or
expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place
objects filled with liquids, such as vases, cups, etc., on or over
the apparatus (e.g., on shelves above the unit).
PORTABLE CART WARNING
20. Grounding
Ensure that you connect the earth ground wire to prevent
possible electric shock (i.e., a TV with a three-prong grounded
AC plug must be connected to a three-prong grounded AC
outlet). If grounding methods are not possible, have a quali-
fied electrician install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone wires, lightning
rods, or gas pipes.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
21. Disconnect Device
14. Never touch this apparatus or antenna during a thunder or
The mains plug is the disconnecting device. The plug must
remain readily operable.
lighting storm.
15. When mounting a TV on the wall, make sure not to install
the TV by the hanging power and signal cables on the back
of the TV.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off
this unit by SWITCH.
16. Do not allow an impact shock or any objects to fall into the
product, and do not drop objects onto the screen.
(Continued on next page)
206-4186
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
26. Do not touch the ventilation openings, as they may become
hot while the TV is operating.
22. Outdoor Antenna Grounding
27. If you smell smoke or other odors coming from the TV or
hear strange sounds, unplug the power cord, and contact an
authorized service center.
If an outside antenna or cable system is connected to the
product, follow the precautions below.
An outdoor antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits or where it can come into contact with such
power lines or circuits as death or serious injury can occur.
28. Do not press against the front panel of the TV with your
hand or a sharp object (e.g., a nail, pencil, or pen) or make a
scratch on it.
29. Keep the product away from direct sunlight.
Be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static
charges.
30. Dot Defect
The LCD panel is a high technology product with resolution
of two million to six million pixels. In a very few cases, you
could see fine dots on the screen while you are viewing the
TV. Those dots are deactivated pixels and do not affect the
performance and reliability of the TV.
Article 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
31. Generated Sound
“Cracking”: A cracking noise that occurs while the TV is
On or when it is turned Off is generated by plastic thermal
contraction due to temperature and humidity. This noise is
common for products where thermal deformation is required.
Antenna Grounding According to NEC, ANSI/NFPA 70
Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies
a large amount of current to operate a product. It varies
depending on the product. This generated sound does not
affect the performance and reliability of the product.
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
32. For LCD TV
Grounding Conductor
If the TV feels cold to the touch, there may be a small “flicker”
when it is turned On. This is normal; there is nothing wrong
with TV. Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots. However,
they have no adverse effect on the TV’s performance. Avoid
touching the LCD screen or holding your finger(s) against
it for long periods of time. Doing so may produce some
temporary distortion effects on the screen.
(NEC Section 810-21)
Electric Service
Equipment
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
23. Cleaning
When cleaning, unplug the power cord and wipe gently with
a soft cloth to prevent scratching. Do not spray water or other
liquids directly on the TV as electric shock may occur. Do not
clean with chemicals such as alcohol, thinners or benzene.
24. Transporting Product
Make sure the TV is turned Off and unplugged and that all
cables have been removed. It may take two or more people
to carry larger TVs. Do not press against or put stress on the
front panel of the TV during transport.
25. Ventilation
Install the TV where there is proper ventilation. Do not install
in a confined space such as a bookcase. Do not cover the TV
with cloth or other materials (e.g., plastic) while it is plugged
in. Do not install in excessively dusty places.
4
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . .3
Commercial Mode Overview. . . . . . . . . . . . . . . . . . . . .6
–
–
Creating an FMA Configuration File using the FTG
Optional Manual Configuration / TV Setup . . . . . . . . . 35
FTG Device Configuration Application Utilities
–
Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote Management in FTG Mode . . . . . . . . . . . . . . . 7
–
FTG Channel Map Configuration Utility . . . . . . . . . . . 37
FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . 38
Pro:Centric Operation. . . . . . . . . . . . . . . . . . . . . . . . . .8
–
Pro:Centric TV Interactive Menu Features . . . . . . . . . . 8
Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
–
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cloning Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Clonable TV Setup Menu Features. . . . . . . . . . . . . . . 11
Master TV Setup Procedure . . . . . . . . . . . . . . . . . . . . 12
References
Upgrading TV/PTC Software using a USB Memory
Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Downloading a Splash Screen using a USB Memory
Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
–
–
Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . 15
Using the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . 15
Exiting the Installer Menu and Activating Updates . . . 15
TV Camport Auto Sense Operation . . . . . . . . . . . . . . . . 46
RJP Model List and Input Auto-sensing Hierarchy. . . . . 49
Resetting Factory Defaults on the TV(s) . . . . . . . . . . . . 50
Channel Icons / Custom Text Labels
(2-5-4 + MENU Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 22
–
Side Connections Panel / RF Antenna & MPI
Learning / Teaching a Master TV Setup using
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
–
–
Learning / Teaching a Master TV Setup using
General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 53
Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . 54
Learning / Teaching a Master TV Setup using
an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . 28
Commercial Mode Check / FTG Operating
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
–
FTG Mode via CPU or EBL. . . . . . . . . . . . . . . . . . . . . 30
Determining the TV Operating Mode . . . . . . . . . . . . . 31
Document Revision History / Notes . . . . . . . . . . . . . . . . 58
Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Notes
• Installer Menu content is intended for use primarily by qualified TV electronics technicians.
• Refer to the Owner’s Manual for additional information on TV installation, features, specifications, maintenance, and safety
instructions.
• Design and specifications subject to change without prior notice.
206-4186
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Commercial Mode Overview
This document describes how to set up LD320H/LD325H and LD340H/LD345H Pro:Centric™ TVs for
Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel
Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded
b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider).
Each of these TV models has an EBL module that can be configured either for Pass-through Mode
(default) or Free-To-Guest (FTG) Mode. In addition, each of these TVs is capable of FTG Mode operation
via the TV CPU when the EBL is in Pass-through Mode.
Setup Checklist
Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s
Manual for detailed information on TV installation and hardware and cable connections.
Installation and Setup Checklist
__ Unpack TV and all accessories.
__ Install batteries in remote control.
__ Install TV on VESA mount or stand.
Note: It may be advisable to make all cable
connections before installing on VESA mount
or stand, as appropriate.
Cable Connections
__ Make all rear jack panel and MPI card slot
connections, as appropriate.
Commercial Mode Setup
__ Complete appropriate procedures as described
in this document for Commercial Mode operation.
See “Pass-through Mode” and “FTG Mode”
sections below for further information.
Hardware Connections
__ Install any additional hardware as
appropriate to your institution, LAN, etc.
Pass-through Mode
This mode allows you to create a Master TV Setup for cloning purposes for TVs that are to remain in
Pass-through Mode. This mode also allows external control via the TV’s GAME CONTROL/MPI port. Use
the Installer Remote to configure Installer Menu items as required for TV operation and set up TV features
(Channel, Picture, Audio, etc.). See “Master TV Setup” on pages 11 to 14 for detailed information.
Installer Menu
To set up a Master TV for cloning purposes, you will
xxLD340H PTC INSTALLER MENU
need to know how to enter the commercial controller
(PTC) Installer Menu and make changes to the
000 INSTALLER SEQ
000
default values as required. If necessary, familiarize
yourself with the Installer Menu and how to make
and save changes. Refer to pages 15 to 21 for
information on accessing the Installer Menu in Pass-
through Mode and for detailed descriptions of the
Installer Menu items.
UPN 000-000-000-000
PTC V1.00.001
ASIC 20E7
CPU V3.25.00
Typical Installer Menu
TV Setup Menus
On-screen setup menus control the features of the
TV. Use the Installer Remote to access the TV setup
menus, and set the TV features to the desired
configuration for the end user. Refer to the Owner’s
Manual for detailed information on the TV setup
menus.
CHANNEL
LOCK
PICTURE
OPTION
TIME
AUDIO
INPUT
MY MEDIA
TV Setup Menus
6
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Commercial Mode Overview (Cont.)
Cloning
Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV (both TVs
must be in Pass-through Mode). The Master TV’s clonable setup menu options should be configured as
part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital
font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be
set incorrectly in the Target TVs. Pages 23 to 29 provide detailed information on cloning requirements and
procedures.
FTG Mode
®
This mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels
to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns
the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be
used is vital in determining the owner.
As indicated above, FTG mode operation in the LD320H/LD325H and LD340H/LD345H models can be
provided either by the TV CPU or EBL (see note below). These are two separate and distinct FTG Modes
of operation, each with its own unique advantages and requirements as described later in this document.
When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV,
and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.
Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, configuration can
begin. Configuration of either requires the LG FTG Device Configuration Application. This application pro-
vides utilities that enable you to create/edit an FTG Channel Map and configure Installer Menu settings.
See pages 30 to 40 for further information on FTG Mode operation and configuration.
Note: LD320H/LD325H TVs must have the following minimum software loads in order to support FTG
Mode via CPU: CPU version 3.61 or later and PTC version 1.01.008 or later. If necessary, contact LG to
obtain LD320H/LD325H CPU and PTC software files, and perform the software updates as described in
Reference section, “Upgrading TV/PTC Software using a USB Memory Device.”
Remote Management in FTG Mode
When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and
FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric™ Server
Admin Client User Guide for further information.
When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows
hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communi-
cate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu set-
tings. See Reference section, “b-LAN Setup & Overview,” for further information.
External MPI Control
To control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port
for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power
circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure
that the GAME CONTROL/MPI port circuitry is powered, thus enabling MPI communication, Installer Menu
item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as
reference section, “b-LAN Setup & Overview,” for further information.
206-4186
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Pro:Centric Operation
Pro:Centric TV Interactive Menu Features
Important: Pro:Centric operation requires that Installer Menu items 098
PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be
in PPV or FTG Mode.
The interactive Pro:Centric TV enables guests—from the comfort of their hotel
rooms—to view and select from a complete listing of hotel services and amenities.
The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities
charges are billed at the time of order.
Interactive amenities may include:
• Hotel information, news, and events
• Directory services (tourist attractions, restaurants, etc.)
• Reservation services (business meetings, fitness, spa, etc.)
• Weather and traffic information
ALARM TIMER INPUT
TV
• Shopping services (delivery to guest room)
• Room service (menu ordering, memo service, morning wake up call, laundry, etc.)
• Ticketing and gaming services
1 2 3
4 5 6
7 8 9
• Check-out service (in the guest room)
• E-mail resources/account access
FLASHBK
0
Use the Installer Remote to operate both interactive menus and regular TV features.
Press PORTAL on the Installer Remote to access the interactive menus.
i
INFO
P
A
G
E
PORTAL
MUTE
CH
VOL
Note: Interactive menu options may vary, depending on Pro:Centric features enabled
for the site. The following are default interactive menus.
GUIDE
MENU
CC
Channel Guide
Shows available TV networks and logical channels. When available, electronic
program guide (EPG) data provides additional channel and program information.
ENTER
Information
RETURN
RATIO
SAP
EXIT
Typically displays hotel information, for example, photos of guest rooms, dining rooms,
business centers, facilities, etc., as well as information on local weather and attractions.
Information may also include resources, such as local school programs, run in coopera-
tion with the hotel.
EJECT
Help
Provides help for navigating the interactive menus.
Watch TV
Removes the interactive menu from the screen and returns to the previously tuned TV
channel.
8
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Pro:Centric Operation (Cont.)
Pro:Centric Setup
The Pro:Centric server provides the following functionality:
• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides
remote management/administration facilities for downloading splash screens and software/firmware
updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for TVs
that are in FTG Mode via CPU (see also “Remote Management in FTG Mode” on page 7).
The Data Channel must be set appropriately in the Installer Menu (item 119 DATA CHANNEL) to enable
Pro:Centric remote management/administration facilities.
• Pro:Centric application: The application comprises the Pro:Centric interactive menus/features described
on the previous page. Pro:Centric application settings are managed via the Pro:Centric server Admin
Client.
In addition to the Data Channel, the Pro:Centric Application Mode must be set appropriately in the
Installer Menu (item 098 PRO:CENTRIC) to enable the Pro:Centric application.
Administration and management options for the Pro:Centric server are described in detail in the
Pro:Centric™ Server Admin Client User Guide. This document describes only those settings that must
be specified on the TVs.
206-4186
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Remote Control Typical Key Functions
The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below
and throughout this document shows typical remote control functions and is provided for reference only. This
Installer Remote may vary from the Installer Remote supplied with the TV.
POWER
Turns TV ON or OFF.
ALARM
Sets the time when the TV
will automatically turn itself ON.
TIMER
ALARM
INPUT
NUMBER Buttons (0 - 9) & DASH
Use to enter a program number or channel.
Dash is used for sub-channel numbers such
as 2-1, 2-2, 9-1, 9-2, 100-3, 100-4, etc.
TV
TIMER
Sets the amount of time before the TV
automatically turns itself OFF.
1 2 3
4 5 6
7 8 9
FLASHBK (FLASHBACK)
Returns to the previously tuned channel.
INPUT
Selects RGB, HDMI/DVI1, HDMI2,
Component Input, AV1, and AV2 sources.
TV
Returns to the last TV channel
(from an Aux input).
Arrows (Up/Down/Left/Right) & ENTER
Use to navigate on-screen menus and
adjust TV settings to your requirements.
MENU
FLASHBK
0
Displays the TV setup menus on the screen.
Also exits the on-screen menu system and
returns to TV viewing.
VOLUME UP/DOWN
Increases/decreases sound level.
i
INFO
INFO
GUIDE
P
A
G
E
Displays channel information.
Displays and removes the electronic
program guide.
PORTAL
MUTE
CH
VOL
PORTAL
Displays and removes the interactive
menu.
CC
Press to activate subtitles.
GUIDE
MENU
CC
MUTE
RETURN
Switches sound ON or OFF.
Returns one level to the previous menu/
display.
CHANNEL/PAGE UP/DOWN
Changes the channel. Moves from
one full set of screen information to
the next.
ENTER
SAP
Analog Mode: Selects MTS sound (Mono,
Stereo, or SAP). DTV Mode: Changes
audio language, if additional languages are
available. *
RETURN
RATIO
SAP
EXIT
EXIT
Color buttons access special functions
in some menus.
Clears all on-screen displays and returns to
TV viewing.
USB BUTTONS
Use to view/navigate USB memory
device content.
RATIO
Adjusts the picture aspect ratio.
EJECT
EJECT
Ejects a USB memory device.
SAP notes:
*
• If SAP is selected and no SAP is provided, sound
may not be heard on channel.
• Each analog channel may have its own SAP setting.
• Digital channels will reset to default audio language
with a power off/on.
10
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Master TV Setup
This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through
Mode.
Note: Refer to FTG Mode information on pages 30 to 40 for details on entering FTG Mode and
configuring/editing FTG Channel Map and FTG Installer Menu settings.
Before You Begin
• Disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions,
Auto Tuning is disabled if there is an Aux input active.
• Determine which cloning tool—USB memory device or clone programmer—is appropriate for your
application. See “Cloning Methods” below for further information.
Cloning Methods
Using a USB Memory Device / .tll File
The .tll file format clones the contents of the commercial controller (PTC) memory, including an auto-tuned/
edited Channel Map, Installer Menu settings, and one TV source’s (analog, digital, or Aux) clonable setup
menu settings. See “Clonable TV Setup Menu Features” list below.
Using a Clone Programmer (TLL-1100A or LT2002)
Both the TLL-1100A and LT2002 clone the contents of the commercial controller (PTC) memory, including
an auto-tuned/edited Channel Map, Installer Menu settings, and one TV source’s (analog or Aux) clonable
setup menu settings. See “Clonable TV Setup Menu Features” list below.
Clonable TV Setup Menu Features
Channel
Audio
Auto Volume
Clear Voice
Sound Mode
Balance
Option
Menu Language
Audio Language
Caption
Auto Tuning (Channel Lineup)
Manual Tuning
Channel Edit
Channel Label
TV Speaker
Lock
Movie Rating
Picture
Aspect Ratio
Picture Mode
Time
Auto Clock
TV Rating – Children
TV Rating – General
Auto Off (Sleep Timer)
Note: Some menu options vary between analog and digital channels and Aux inputs.
206-4186
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Master TV Setup (Cont.)
Master TV Setup Procedure
1. Set Installer Menu items.
This step provides specific instruction only on the Installer Menu
items that should be set on a Master TV. Refer to pages 15 to 21
for detailed information on all Installer Menu items.
xxLD340H PTC INSTALLER MENU
a) Make sure the TV is ON. Then, use the Installer Remote to
enter the PTC Installer Menu: Press MENU repeatedly until
the on-screen display of the TV setup menus no longer
toggles, and then press 9-8-7-6 + ENTER.
000 INSTALLER SEQ
000
UPN 000-000-000-000
PTC V1.00.001
ASIC 20E7
CPU V3.25.00
b) Set Installer Menu item 117 FACT DEFAULT to 001 and press
ENTER on the Installer Remote.
This clears all Installer Menu custom settings, channel lineup,
etc. and reloads the factory default settings. The value will
change back to 0 after the PTC has been restored to factory
default condition. This step ensures that the TV Channel
Memory will be the active channel lineup.
Typical Installer Menu
Note: The Installer Menu header will vary
depending on the TV you are setting up.
117 FACT DEFAULT
003 BAND/AFC
001
00X
c) Set Installer Menu item 003 BAND/AFC, as appropriate.
• Broadcast: Set to 000.
• HRC: Set to 002.
• IRC: Set to 003.
• CATV: Set to 001 (default).
Adjust the settings for these
Installer Menu items.
d) Set any other Installer Menu items that affect your TV pro-
gramming network to the required configuration. For example,
enable/disable Aux inputs, set a Start Channel, etc.
e) After you have adjusted all required Installer Menu item
settings, press ENTER once on the Installer Remote to save
your changes; then, press ENTER again to exit the menu.
CHANNEL
LOCK
PICTURE
OPTION
TIME
AUDIO
INPUT
2. Set up TV features.
On-screen setup menus control the features of the TV. Press
MENU on the Installer Remote to access the TV setup menus,
and then set Channel, Picture, Audio, Lock, Time, etc. options to
the desired configurations. See also the Clonable TV Setup Menu
Features list on page 11.
MY MEDIA
Use the TV setup menus to set the TV
features to the desired configuration
for the end user.
Note: Remember that only one TV source’s clonable setup menu
settings will be cloned. Thus, for a clone programmer, the TV
setup menu settings should be applicable to either an analog
channel or Aux input, while for a USB memory device, the TV
setup menu settings should be applicable to the analog or digital
channel or Aux input to which the Target TV will be set during the
Teaching process.
Note: If desired, you can run Auto Tuning (see step 3) prior to
completing this step.
(Continued on next page)
12
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Master TV Setup (Cont.)
(Continued from previous page)
3. Run Auto Tuning.
a) To search for all available analog and digital channels, go to the
Channel Menu, select the Auto Tuning option, and follow the
on-screen instructions.
Move
Enter
CHANNEL
Auto Tuning
Manual Tuning
Channel Edit
Channel Label
b) Use the Channel Edit option in the Channel Menu to edit the
channel lineup, as necessary, to include only free to guest
(non-encrypted) channels.
• Add/delete channels per your system requirements.
• Use the Channel Label option in the Channel Menu to select
the appropriate trademark/icon for each channel’s Channel-Time
on-screen display. Icons are available for familiar channels,
such as ABC, CBS, NBC, etc. Identifiable labels (icons) should
enable the end user to readily know what common networks are
available.
Use Channel Menu options to
run Auto Tuning, edit channels,
and select channel icons.
Note: If Installer Menu item 103 ATSC TUNE MODE is set for Physical Channel
tuning (default and recommended setting), channels with minor channel numbers
higher than 255 will not transfer correctly in step 5. If item 103 is set for Virtual
Channel tuning and either the major or minor channel numbers are higher than
255, the channel(s) will not transfer correctly in step 4.
Note: You can add the channel icons in this step or as described in step 6. Also in
step 6, you can add custom text labels for channels without icons.
4. Transfer the TV setup menu settings to the commercial controller (PTC):
2-5-5 + MENU Mode
Important: This step is essential for successful cloning. Without this step, the
PTC will not contain any of the TV setup menu settings.
a) After the TV channel lineup has been edited and channel label icons added, tune to
the channel (source) for which you wish to transfer TV setup menu settings.
Note: If you intend to use a clone programmer for cloning purposes, this must be
either an analog channel or Aux input.
b) Enter the Installer Menu, and press 2-5-5 + MENU on the Installer Remote to
initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer
Menu and then tunes through the channels in the channel lineup during the
transfer. When the transfer is complete, the TV tunes back to the channel that
was tuned before the transfer began.
Note: The maximum number of channels that can be transferred is 141. An attempt
to transfer more than 141 channels will result in erratic TV tuning operation.
(Continued on next page)
206-4186
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Master TV Setup (Cont.)
(Continued from previous page)
DIGITAL 19-3
5. (Optional) Add Custom Channel and Aux Input Labels:
2-5-4 + MENU Mode
MONO STEREO SAP
Note: 2-5-4 + MENU Mode enables you to add/edit channel icons
and custom text labels in the PTC once the Master TV Setup has
been transferred as described in the previous step.
WXYZ
Enter the Installer Menu, and press 2-5-4 + MENU on the Installer
Remote. Add/edit custom text labels and/or change icons for the
Channel-Time on-screen displays (see 2-5-4 + MENU procedural
information on page 22). Note that broadcast digital channels often
already have a broadcaster generated label. When you are finished,
press MENU to exit 2-5-4 + MENU Mode.
Custom text label “WXYZ” created
in 2-5-4 + MENU Mode.
028 CH. OVERIDE
000
6. Verify the TV setup.
After verifying the TV Setup, set Installer
Menu item 028 CH. OVERIDE to 000.*
Verify that the channel lineup, channel icons, and custom text labels are
correct. Also, make sure the TV features are set per your requirements.
* This step prevents end users from
accessing channel settings (i.e., the
Channel Menu will be inaccessible/
grayed out).
7. Lock the channel lineup.
Enter the Installer Menu. Set item 028 CH. OVERIDE to 000 and
press ENTER to lock the channel lineup and restrict access to the TV
setup menus. Press ENTER again to save your changes and exit the
Installer Menu.*
The Master TV Setup is now ready to be copied to the predetermined
cloning tool—a USB memory device or a clone programmer. See cloning
procedures in this document.
14
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu
Use the Installer Menu to set up or change operational settings.
Refer to the table starting on the next page for brief descriptions of Installer Menu items.
More detailed descriptions follow the table listing.
Accessing the Installer Menu
1. Make sure the TV is ON.
2. Using an Installer Remote, press MENU repeatedly until the on-
xxLD340H PTC INSTALLER MENU
screen display of the TV setup menus (if the TV is in Pass-through
Mode) or the Function Menu (if the TV is not in Pass-through Mode)
no longer toggles, and then press 9-8-7-6 + ENTER to access the
Installer Menu.
000 INSTALLER SEQ
000
The Installer Menu opens with item 000 INSTALLER SEQ 000.
UPN 000-000-000-000
PTC V1.00.001
ASIC 20E7
CPU V3.25.00
Note: If the password is not entered or registered correctly, you will see
the message “ENTER PASSWORD 0000” at the top of the screen instead
of the Installer Menu header. Once you re-enter the correct password
(i.e., press 9-8-7-6 + ENTER), the Installer Menu will display.
Typical Installer Menu
Note: If the TV is in FTG Mode, the Installer Menu is accessible as read-
only. Refer to pages 30 to 40 for information on FTG Mode configuration.
Using the Installer Menu
Refer to the table on pages 16 and 17 for an overview of the available Installer Menu items,
including their item numbers, functions, value ranges, and default values. Installer Menu items
not relevant to this TV series are not present in the Installer Menu; therefore, some numbers are
missing. For example, item 006 will not appear.
Navigation within the Installer Menu
Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu
items, or access an item directly by keying in the line number and then pressing MENU. For
example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.
Changing Installer Menu Settings
To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote,
or enter a valid value directly. To save the new setting, press ENTER, or use the Up/Down
arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note
that invalid values will not be saved.
Exiting the Installer Menu and Activating Updates
After you have adjusted all required Installer Menu item settings, press ENTER once on the
Installer Remote to save your changes; then, press ENTER again to exit the Installer Menu. Any
changes you make will be stored in non-volatile memory.
Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control)
settings in the TV are reset to their default values; that is, the Lock System, if previously enabled
from the Lock setup menu (see the Owner’s Manual for additional information), will now be
disabled, and the individual Parental Control settings will be restored to default values.
206-4186
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Installer Menu Items 000 through 071
Menu
Function
Value Range
Default Value
Brief Description of Function and Comments
Item
000
001
002
003
INSTALLER SEQ
POWER MANAGE
AC ON
0 ~ 3
0 ~ 7
0 / 1
0
0
0
1
Leave default set to 0.
Sets number of hours of no activity before automatic shutoff.
Set to 1 to enable Auto Turn ON when AC power is applied.
Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
BAND/AFC
0 ~ 3
Channel tuned when TV is turned ON. (Set to 255 to tune to channel
tuned before TV turned OFF.)
004
005
007
STRT CHANNEL
CHAN LOCK
0 ~ 127, 255
0 / 1
255
0
If set to 1, cannot tune from current channel.
Volume level when TV is turned ON. (Set to 255 to use volume level
before TV turned OFF.)
STRT VOLUME
0 ~ 63, 255
255
008
009
010
011
015
016
017
020
021
022
023
028
029
030
031
032
034
035
038
039
MIN VOLUME
MAX VOLUME
MUTE DISABLE
KEY DEFEAT
SLEEP TIMER
EN TIMER
0 ~ 63
0 ~ 63
0 / 1
0
63
0
Sets minimum allowable volume setting.
Sets maximum allowable volume setting.
Set to 1 to disable Mute Function.
0 / 1
0
Set to 1 to disable menu navigation keys on display panel.
Set to 1 to enable Sleep Timer.
0 / 1
1
0 / 1
0
Set to 1 to enable On/Off Timers.
ALARM
0 / 1
1
Set to 1 to enable Alarm.
FEATURE LEVEL
V-CHIP
0 ~ 1, 16 ~ 24
0 / 1
1
Determines an additional IR code scheme to which the TV will respond.
Set to 1 to enable V-Chip (Parental Control) functions.
Sets number of V-Chip blocking hours.
1
MAX BLK HRS
CAPTION LOCK
CH. OVERIDE
OLD OCV
0 ~ 99
0 / 1
12
0
Set to 1 to retain caption setting set before TV turned OFF.
If set to 0, limits direct access to favorite channels.
Set to 1 to change MPI operation to OCV.
If set to 1, enables ACK feature of MPI.
0 / 1
1
0 / 1
0
ACK MASK
0 / 1
0
POLL RATE
20 ~ 169
186 ~ 227
0 / 1
94
207
1
Selects poll rate for MPI.
TIMING PULSE
CAMPORT EN
COMPPORT EN.
YPrPb EN.
Sets baud rate for MPI.
Set to 1 to enable Video 2 input.
0 / 1
1
Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1.
Set to 1 to enable display panel Component Video 1 input jacks.
Set to 1 to enable display panel Video 1 input jack.
0 / 1
1
REAR AUX EN
0 / 1
1
Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE
cannot be set to 2.
040
046
047
AUTO CAMPORT
STRT AUX SRCE
AUX STATUS
0 / 1
1 ~ 6, 255
0 / 1
1
6
0
Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).
Set to 1 for MPI Aux source to be reported as a channel number instead of
Channel 0.
053
069
070
071
DIS. CH-TIME
EN. CH-T COL.
FOR. CH-TIME
BCK. CH-TIME
0 / 1
0 / 1
0 ~ 7
0 ~ 7
0
1
2
2
Set to 1 to disable Channel-Time display.
Set to 1 to enable custom color for the Channel-Time display.
Chooses custom foreground color for the Channel-Time display.
Chooses custom background color for the Channel-Time display.
16
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Installer Menu Items 073 through 119
Menu
Item
Function
Value Range
Default Value
Brief Description of Function and Comments
If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message
is displayed if user direct tunes a channel that is not in the favorite channel list.
073
CH NOT AVBLE
0 / 1
0
075
078
079
080
081
082
REVERT CH
UPN MSB
0 / 1
0
0
0
0
0
1
If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.
User programmable number, most significant byte.
User programmable number, most significant byte - 1.
User programmable number, most significant byte - 2.
User programmable number, least significant byte.
Enforces rigid MPI checksum.
0 ~ 255
0 ~ 255
0 ~ 255
0 ~ 255
0 / 1
UPN MSB-1
UPN MSB-2
UPN LSB
CHKSM ERROR
Relaxes MPI timing to be compatible with PC-based Windows-
controlled systems.
083
084
087
HANDSHK TIME
PERMANENT BLK
REAR RGB EN.
0 ~ 5
0 / 1
5
0
1
Removes block hours setting for Parental Control and makes block permanent.
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.
Set to 1 to enable RGB input. Set to 17 for Auto Configure.
0/1/17
088
090
091
EN NOISE MUTE
KEY LOCK
0 / 1
0 / 1
0 / 1
1
0
1
If set to 1, audio is muted if no signal is present.
If set to 1, keyboard is locked out, IR is still functional.
Set to 1 to enable HDMI 2 input.
YPrPb2 EN
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
093
RJP AVAILABLE
0, 1, 2, 5, 6
0
Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on
Function Menu.
094
096
098
SAP MENU EN
DEF. ASP. RATIO
PRO:CENTRIC
0 / 1
0 ~ 4
0 ~ 2
1
2
0
Sets default aspect ratio at power up. See detailed descriptions and item 106.
Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for
GEM (Java Application) Mode.
1 ~ 100,
101 ~ 200, 255
099
BACK LIGHTING
100
Sets the level of the TV picture back lighting. (See detailed descriptions.)
102
103
104
ATSC BAND
0 ~ 4
0 / 1
4
1
0
Selects ATSC band.
ATSC TUNE MODE
START MINOR CH
Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
Selects Minor Start Channel. Set to 0 for NTSC.
0 ~ 255
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
power cycle.
106
ASP RATIO LOCK
0 / 1
0
116
117
VIDEO MUTE EN
FACT DEFAULT
0 / 1
0 / 1
0
0
Set to 0 for Normal. Set to 1 for Blank.
Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.
Set to 3 (default—b-LAN module only powered when TV is turned ON), or set
118
119
POWER SAVINGS
DATA CHANNEL
1 / 3
3
0
to 1 (b-LAN module is always powered). (See detailed descriptions.)
Set to 0 to disable. Set to the RF channel number of the Data Channel for
Pro:Centric or TV E-Z Installation data. (See detailed descriptions.)
0 ~ 135
Caution: Installer Menu settings may affect options available
from the TV setup menus or the Function Menu.
206-4186
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Detailed Descriptions of Installer Menu Items
NOTE: For items 007, 008, and 009
000 - INSTALLER SEQUENCE
For legacy reasons, the scale used is 0 – 63. The PTC software
will translate this to the 0 – 100 scale used by the TV.
Specifies entry sequence to the Installer Menu.
0 = 9876
2 = 1478
1 = 4321
3 = 3698
To translate a TV volume level to the Installer Menu value, use
the following formula:
001 - POWER MANAGE (Power Management)
Installer Value = TV Value x 63
100
Determines hours of no activity before automatic shutoff. The
Power Management function is for saving energy. If set to 0,
Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7
representing the hours that the unit will remain ON, unless there
has been activity from either the control panel or remote control.
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful
for an in-house information channel, since the TV would always
select that volume level when it is turned ON. The range of values
are 0 - 63, 255. If 255 is selected, the current volume level will be
retained in memory when the TV is turned OFF; at turn ON, the
volume level will be automatically set at the previous or last level.
002 - AC ON (AC Power Switchable)
If set to 1, this allows the TV to turn ON when AC power is applied.
Pressing the ON button is not necessary. This is desirable if the TV
is plugged into a cable box or a power outlet controlled by a wall
switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is
the default (OFF), and 1 is ON.
Note: If set to 1 (ON), the TV does not respond to ON/OFF
commands from either the remote or the display panel, and the
SLEEP TIMER is also nonfunctional.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. Use the Left/Right arrow keys to change values.
The factory default is 0, which provides the full range of volume
control, if item 009 MAX VOLUME is also set to 63. It may be best
to set the same value on every TV.
003 - BAND/AFC (Band/Automatic Frequency Control)
There are four possible settings for this option:
0 = Broadcast
2 = HRC
1 = CATV (default)
3 = IRC
If some channels were not found by Auto Tuning (Channel
Search), select the appropriate Band setting here, and add the
channels using the Channel Edit option in the Channel Menu.
Note: The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
004 - STRT CHANNEL (Start Channel)
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb
others. The value range is 0 to 63, with 63 as the default, which
gives the user the full range of volume control, if item 008 MIN
VOLUME is also set at 0. Use the Left/Right arrow keys to change
values. It may be best to set the same value on every TV.
If active, this function allows you to determine the initial Major
Start Channel number when the TV is turned ON. This feature is
useful for an in-house information channel, since the TV would
always select that channel when it is turned ON. Setting this item
to 255 causes the last channel viewed when the TV was turned
OFF, to be the tuned to channel when the TV is turned ON again.
Note: For a digital Start Channel, always remember to set item
104 to the Minor Start Channel number.
Note: The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
255 = Last channel
1 ~ 125 = Major Ch. #
0 = Aux
126 = Map to Channel 3 127 = Map to Channel 4
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted. If set to 0, sound can be muted.
005 - CHAN LOCK (Channel Lock)
Channel Lock is ideal if the system must always be on the same
channel. Changing channels with the Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (default).
011 - KEY DEFEAT (Keyboard Defeat)
If set to 1, KEY DEFEAT prevents the end user from accessing
the on-screen menu(s) from the display panel—MENU, ENTER,
and menu navigation keys do not function. If set to 0, those keys
do function.
Generally, this feature is used in connection with item 004 STRT
CHANNEL where the Start Channel may, for example, be set to
3 or 4. If the Start Channel is 3, then the TV will remain locked on
channel 3.
Note: Users can always access the menu(s) by pressing MENU
on the remote.
18
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
015 - SLEEP TIMER
031 - POLL RATE
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
MPI Communication Parameter. Selects poll rate for MPI. Step
size of 16 ms. Changing from default may affect communication
via MPI.
016 - EN TIMER (Enable On/Off Timers)
032 - TIMING PULSE
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
MPI Communication Parameter. Sets baud rate for MPI. Step size
of 4.3 uS. Changing from default may affect communication via
MPI.
Note: Clock must be set in order for timers to be used.
017 - ALARM
034 - CAMPORT EN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display panel. If set to 0, Video
2 input on display panel is not functional.
Gives the installer the option of making the Alarm function avail-
able to the end user. If set to 1, the Alarm function is available to
the end user. Set to 0 to disable the Alarm function.
Note: Clock must be set before the Alarm function will work.
035 - COMPPORT EN. (Computer Port Enable)
Enable/disable TV display panel HDMI 1 input jack. Set to 0 to
disable HDMI1. Set to 1 to enable HDMI1.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video input jacks.
Set to 0 to disable display panel rear Component Video input jacks.
IR Mode
Bed #
1 – 2
Values
0 – 1
Legacy (Hospital)
Multi-code Remote
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0
to disable display panel rear Aux (Video 1) input.
1 – 9
16 – 24
Note: For further information, see documentation for the accessory
package that includes the multi-code remote.
040 - AUTO CAMPORT
Set to 1 to automatically switch to Camport when equipment is
connected to side Video input. Set to 0 to disable side Video
automatic source selection. If set to 1, STRT AUX SRCE cannot
be set to 2.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to filter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
Note: If set to 1, item 093 RJP AVAILABLE is automatically set to 0.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the TV will tune to
starting Aux source if item 004 STRT CHANNEL is set to 0.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO
CAMPORT is set to 0:
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1 to 1 = Video 1
4 = RGB
255 = Last Aux
use the caption setting configured before the TV was turned OFF
when the TV is turned ON.
2 = Video 2
3 = HDMI 1
5 = HDMI 2
6 = Component
If item 093 RJP AVAILABLE is set to 1:
2 = Video 2 5 = HDMI 2 6 = Component
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/
Down or by direct keypad entry. If set to 0, only those channels
that are active in the TV’s memory can be selected.
If item 040 AUTO CAMPORT is set to 1:
1 = Video 1
3 = HDMI 1
4 = RGB
5 = HDMI 2
6 = Component
029 - OLD OCV (On Command Video™)
Set to 1 for operation with systems from On Command Corporation.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number
instead of channel 0. Set to 0 to disable Aux identification change.
Controls MPI status channel response for Aux inputs.
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.
206-4186
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display; Channel-Time
display will not appear. Set to 0 to enable the Channel-Time
display.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing MPI timing requirements to be compatible with PC-
based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the Channel-Time display. Set
to 0 to disable custom color for the Channel-Time display.
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent
by disabling the blocking hours function. Set to 1 to install Parental
Control restrictions permanently. Set to 0 for user-specified hours
control of blocking schemes.
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set according to Color Chart:
0 = Black
1 = Blue
2 = Green
3 = Cyan
4 = Red
5 = Violet
6 = Yellow
7 = White
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV. Set to 0 to disable RGB
input. Set to 1 to enable RGB input. Set to 17 to initiate a one-
time automatic configuration after an AC power cycle; otherwise,
automatic adjustment will be performed each time the RGB input
is accessed.
Note: If foreground color and background color are the same, the
menu background will be transparent.
Note: Applies only to “Channel Not Available” message if item
073 CH NOT AVBLE is set to 1 (enabled).
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
See description for item 070 FOR. CH-TIME above. The color
chart is the same for both items.
090 - KEY LOCK
If set to 1, display panel Channel, Volume, and Caption buttons
are disabled, Power button remains enabled. If set to 0, Channel,
Volume, Caption, and Power buttons are all enabled.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL-
ABLE” message is displayed when a user direct tunes a channel
that is not in the channel scan list available in memory.
091 - YPrPb2 EN. (HDMI2 Enable)
Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable
display panel HDMI 2 input.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, TV automatically
tunes to the specified Start Channel.
093 - RJP AVAILABLE (Remote Jack Pack Available)
• 0 = Remote jack pack is not available or disabled.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by
MPI command. Note: Not linked to serial number.
• 1 = Legacy Model RJPs: HDMI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI source is connected to the RJP, both
digital video and audio are expected via the HDMI cable. If no
digital audio is present, no audio will be heard.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
MPI command. Note: Not linked to serial number.
• 2 = Legacy Model RJPs: DVI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI/DVI source is connected to the RJP,
only digital video is expected via the HDMI cable. Analog audio
is provided via a separate cable, from the source, connected to
an RJP AUDIO IN. If no analog audio cable is connected, tuner
audio will be heard.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
MPI command. Note: Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by
MPI command. Note: Not linked to serial number.
• 5 = Scaler Model RJPs: HDMI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI source is connected to the RJP,
both digital video and audio are expected via the HDMI cable. If
no digital audio is present, no audio will be heard.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async port).
SPI is always checked.
20
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
• 6 = Scaler Model RJPs: DVI Mode
104 - START MINOR CHANNEL
Enables RJP feature for use with reduced cable bundle models. Sets Minor Start Channel number at power up. 0 = NTSC. If not
In this mode, when an HDMI/DVI source is connected to the
RJP, only digital video is expected via the HDMI cable. Analog
audio is provided via separate cable, from the source, connect-
ed to an RJP AUDIO IN. If no analog audio cable is connected,
tuner audio will be heard.
0, number selected is the digital channel’s Minor Start Channel
number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
Notes:
See Reference section, “RJP Model List and Input Auto-sensing
Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040
AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6
allow the lodge staff to customize each TV’s RJP setup based on
customer requirements.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to load presets of all Installer Menu
item settings.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function Menu, if Function
Menu is available (i.e., TV is not in Pass-through Mode). Set to
0 to disable SAP feature on Function Menu, if Function Menu is
available.
Caution: If set to 1, this will reload the factory
defaults and clear the channel lineup, including any
assigned channel icons and custom text labels.
Note: See also Reference section, “Resetting Factory Defaults on
the TV(s),” for further information.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up.
• Set to 0 for Set By System.
• Set to 1 for 4:3.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded b-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is in Standby Mode, the MPI
card slot is powered by the Standby power supply and both the
embedded b-LAN and the GAME CONTROL/MPI port are not
powered. When the TV is in Power On Mode, the MPI card slot is
powered by the main 12V power supply and both the embedded
b-LAN and GAME CONTROL/MPI port are powered.
• Set to 2 for 16:9 (Factory Default).
• Set to 3 for Just Scan.
• Set to 4 for Zoom.
Note: Only applies if item 106 ASP RATIO LOCK is disabled, i.e.,
set to 0.
098 - PRO:CENTRIC
Note that the TV must be turned ON in order to communicate with
the embedded b-LAN module for configuration and control when
POWER SAVINGS is set to 3. If set to 1, the b-LAN module is
always powered.
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2
for GEM (Java Application) Mode.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 100.
• 1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7,
LMT7Z9—are NOT supported in TVs in which b-LAN technology
is already integrated.
• 101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
Note: See Reference section, “b-LAN Setup & Overview,” for
further information.
If set between 101 and 200, the TV automatically controls back
lighting depending upon the picture level of the current program. If
set to 255, back lighting is controlled via the Picture settings in the
TV’s setup menus.
119 - DATA CHANNEL
Set to 0 (default) to disable. Set to the RF channel number of the
data channel for Pro:Centric or TV E-Z Installation (splash screen,
configuration, or firmware) data.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
Note: Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. Also, while
Pro:Centric updates are in progress, it is not possible to turn the
TV ON. The TV may take several minutes to load EPG data after
the initial download of the Pro:Centric application. Subsequent
updates generally will take less than one minute.
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
206-4186
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)
Changing Channel Icons and/or Adding or Editing
Custom Text Labels in the Channel-Time Display
Changing icons and/or adding or editing custom text labels
can only be done if there are channels that have been
transferred to the TV’s PTC either during Master TV Setup
(see pages 11 to 14) or by cloning.
If there is no pre-assigned icon for a channel, you can add
a custom text label of up to seven (7) characters to help
identify the channel or network. Also, if desired, a custom
text label can be added to the Channel-Time display in
addition to a pre-assigned icon. You may also add text
labels for the Aux input sources to clearly identify the
devices that are connected to the Aux inputs.
Note: A blank letter space is available between “Z” and “!”.
To perform channel editing/labeling:
1. Enter the Installer Menu: Press MENU repeatedly until
the on-screen display of the TV setup menus no longer
toggles, and then press 9-8-7-6 + ENTER.
(Icon)
2. Press 2-5-4 + MENU on the Installer Remote to enter
the Channel Label Editing Menu.
XYZ
XYZ
XYZ
3. Change channel icons and/or add or edit custom text
labels as described in the procedures below. (You can
do this more than once.)
NETWORK
(Custom Text Label)
1 2 3 4 5
7
6
4. To exit the menu when you are done, press MENU.
Changing a Channel’s Icon on
the Master TV
Adding/Editing Channel Labels
on the Master TV
Adding/Editing Source Labels
on the Master TV
1. Use Channel Up/Down to select
the desired channel.
1. Use Channel Up/Down to select
the desired channel.
1. Press INPUT to select the desired
Aux input source: AV1, AV2, RGB,
Component, HDMI, or HDMI2.
2. Use the Left/Right arrow keys
to select the thin letter “I” on the
Channel-Time display.
2. Press the Left or Right arrow
repeatedly until the numbers 1 to 7
appear on the display. The number
shows the position of the character
that can be changed. Number 1 is
the first character, number 2 the
second character, etc.
2. Press the Left or Right arrow
repeatedly until the numbers 0 to 9
appear on the display. The number
shows the position of the character
that can be changed.
3. Use the Up/Down arrow keys to
select the icon with which you want
to identify the channel. (If you know
the icon number, enter the number,
and press ENTER.)
3. Use the Up/Down arrow keys to
select the desired character.
3. Use the Up/Down arrow keys to
select the desired character.
4. Proceed to add/edit custom text
labels, or go to the next channel.
4. Press INPUT for the next Aux input,
or use Channel Up/Down to return
to channels.
4. Proceed to the next number posi-
tion, or go to the next channel.
Installer Remote Control Key Functions for Master TV Channel Label Editing Menu
• Channel Up/Down: Tunes to the next channel in scan.
• Left/Right Arrows: Select the item to change. If “I” is
shown, the icon can be changed. If a number is shown, it
indicates the position of the character that can be changed.
• Up/Down Arrows: Select the icon or the character to be
displayed. Tip: Arrows can be held down for fast scrolling.
• 0 – 9: Use to enter the index number of the icon, if
known.
• ENTER: Changes the icon after the icon number has
been entered.
• INPUT: Changes the Aux input label.
• MENU: Exits the editing process.
22
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Cloning Overview
IMPORTANT CLONING INFORMATION
There are three different procedures for cloning a Master TV Setup, each with its own advantages and
limitations (see also “Cloning Methods” on page 11):
• Using a USB memory device
• Using a TLL-1100A clone programmer
• Using a LT2002 clone programmer
Each cloning method is described in further detail on the pages that follow. As you perform cloning
procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not
performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows
the proper message when cloning. If the message indicated does not appear, there is a problem with that
step, and cloning may not be successful.
Caution: Copying a blank or incorrect memory into a TV from a clone programmer will
cause the TV to operate erratically or become inoperable.
Caution: Do not connect a clone programmer to a PPV card installed in the Master or
Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if
you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port.
Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Before you begin cloning:
• Complete the Master TV Setup procedure (see pages 11 to 14).
• All equipment should be connected to power and turned ON.
• Both the Master and Target TVs must be in Pass-through Mode.
• Learning and Teaching is only possible between identical model TVs.
• If using a USB memory device, ensure the USB device has been formatted with FAT format.
• For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux
input or an analog (not a digital) channel.
• LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the
clone programmer clock time (if set) will be lost (see page 29 for information on the clone programmer
clock).
Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/
clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction
or harm the USB device/clone programmer, respectively.
206-4186
23
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedure
Learning / Teaching a Master TV Setup using a USB Memory Device
USB Cloning Notes
• Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures.
• You may edit a filename as part of the Learning procedure; however, a file with edited contents will not
be recognized.
• It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock
manually, or use the Auto Clock setting in the TV setup menus.
Learn Setup from Master TV
USB Download Menu
1. Ensure the Master TV is set up completely and in Pass-through
Mode.
Upgrade TV Software
Upgrade PTC Software
2. Plug the USB memory device into the USB IN port on the Master
TV.
Teach To TV (TLL)
Teach To TV (FMA)
Learn From TV (TLL)
Learn From TV (FMA)
3. Press MENU on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the
Option menu icon, and then press the number “7” key a total of
seven times to display the USB Download Menu.
Return
Enter
4. To gain access to the “Learn From TV” option in the USB
Download Menu, key in the password used to enter the Installer
Menu (Example: Press 9-8-7-6).
Learn From TV (TLL)
Select the file name and press OK to start
xxLD340H-UA00001.TLL
5. Use the Up/Down arrow keys to select Learn From TV (TLL),
and then press ENTER.
6. To differentiate this .tll file from others, you can use the Up/Down
arrow keys to change the last five digits of the filename. Press
ENTER when you are ready to initiate Learning.
Return
Enter
Learn From TV
UPDATING...
!
Learning status will be shown on the progress bar. When the
Learning process is complete, the USB Download menu will
reappear on screen.
25%
Do not remove the USB from the port!
Do not unplug!
7. When Learning is done, remove the USB memory device from the
Master TV.
24
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedure (Cont.)
Learning / Teaching a Master TV Setup using a USB Memory Device (Cont.)
Teach Master TV Setup to Target TV
1. Ensure the Target TV is in Pass-through Mode, and then use the
Installer Remote to enter the Target TV Installer Menu: Press
MENU repeatedly until the on-screen display of the TV setup
menus no longer toggles, and then press 9-8-7-6 + ENTER.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
2. Set Installer Menu item 117 FACT DEFAULT to 001, and press
ENTER. When the value changes back to 0, press ENTER again to
exit the Installer Menu.
Teach To TV (FMA)
Return
Enter
3. Tune/set the TV to an analog or digital channel or Aux input, (ideally
the same source tuned for 2-5-5 + MENU Mode during the Master
TV Setup procedure).
Teach To TV (TLL)
xxLD340H-UA00001.TLL
4. Plug the USB memory device with the .tll file into the Target TV
USB IN port.
5. Press MENU on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the
Option menu icon, and then press the number “7” key a total of
seven times to display the USB Download Menu.
Return
Enter
Teach To TV
UPDATING...
!
6. Use the Up/Down arrow keys to select Teach To TV (TLL), and
50%
then press ENTER.
Do not remove the USB from the port!
Do not unplug!
7. Use the Up/Down arrow keys to select the Master TV Setup you
want to install, and then press ENTER. Note: Filenames identify
the TV and the TLL version (see example at right).
Teaching status will be shown on the progress bar. When the
Teaching process is complete, the USB Download menu will
reappear on screen.
8. When Teaching is done, remove the USB memory device from
the Target TV, turn OFF the TV, and unplug the TV power cord for
15 seconds.
9. Reconnect the TV power cord, and turn ON the TV. The Master
TV Setup should be resident on the Target TV.
206-4186
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer
Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target
TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are
not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of
these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning is accomplished using the
TV/clone programmer MPI ports for
communication (see figure).
TLL-1100A Clone
TV Link
Loader
Programmer
TLL1100A
Ready
Antenna
or CATV
TLL-1100A Cloning Notes
• Read the IMPORTANT CLONING
INFORMATION on page 23 before
beginning any cloning procedures.
MODE
MENU
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
MPI
ENTER
• Ensure the TLL-1100A is either fully
charged or connected to AC power.
Cable
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
RECEIVE
SEND
(6) DISPLAY CLONE SETUP
• Learning and Teaching is only
TLL-1100A
possible between identical model
TVs; however, the TLL-1100A can
store up to eight different Master
TV Setups.
Learn Setup from Master TV
1. Ensure the Master TV is set up completely and in Pass-through Mode.
2. Tune/set the TV to an analog channel or Aux input, and then, plug one
end of the MPI cable into the TV MPI port.
3. Turn ON the TLL-1100A.
4. Use the MODE button on the TLL-1100A to select Clone Mode.
5. Use the Left/Right arrows on the TLL-1100A to select the Memory CBank
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
(1 to 8) in which to store the Master TV Setup.
6. Plug the other end of the MPI cable into the MPI port on the bottom of the
TLL-1100A. The Clone Selection Menu will display on the TV screen.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
7. Press 1 on the Installer Remote to select LEARN FROM TV from the
Clone Selection Menu. Then, press ENTER to transfer the Master TV
Setup into CBankX on the TLL-1100A.
(6) DISPLAY CLONE SETUP
CLONE CLOCK = XX:XX
Learning usually takes about 90 seconds. “LEARNING IN PROGRESS”
will be displayed on the screen while the TLL-1100A copies the Master
Setup. When the Learning process is complete, a “LEARNING COM-
PLETE” message will be displayed.
TV
CLOCK = XX:XX
THE CLONE IS VERSION VX.X.X
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
8. When Learning is complete, disconnect the MPI cable from the Master TV.
26
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.)
(Optional) Set the Clock
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
Set the time on a Master TV’s clock. (If the time has already been copied
from a TV into the TLL-1100A clone programmer, you can set the Master
TV’s clock by copying the time from the clone programmer.) The TLL-1100A
can copy the current time to both a Master TV and to the clone’s internal
clock—accurate to within one minute.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
Since the TLL-1100A’s time cannot be set directly, the current time needs
to be copied from an LG TV equipped with an enabled MPI port.
CLONE CLOCK = XX:XX
TV
CLOCK = XX:XX
After the time is copied to the TLL-1100A clone programmer, the current
time will be maintained and can then be transferred to another TV. (This
can be a Master TV or another TV which has already had the features set
up.)
THE CLONE IS VERSION VX.X.X
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
Teach Master TV Setup to Target TV
1. Ensure the Target TV is in Pass-through Mode, and then use the Installer
Remote to enter the Target TV Installer Menu: Press MENU repeatedly
until the on-screen display of the TV setup menus no longer toggles, and
then press 9-8-7-6 + ENTER.
2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER.
When the value changes back to 0, press ENTER again to exit the
Installer Menu.
3. Tune/set the TV to an analog channel or Aux input (ideally the same
source tuned for 2-5-5 + MENU Mode during the Master TV Setup
procedure), and then connect the MPI cable to the MPI port on the Target
TV. The Clone Selection Menu will display on the TV screen.
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
4. Ensure the correct Memory CBank(X) is selected on the TLL-1100A.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
5. Press 2 on the Installer Remote to select TEACH TO TV from the Clone
Selection Menu. Then, press ENTER to transfer the Master TV Setup to
the Target TV.
(6) DISPLAY CLONE SETUP
Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will
be displayed on the screen during Teaching. When the Teaching process
is complete, a “TEACHING COMPLETE” message will be displayed.
CLONE CLOCK = XX:XX
TV
CLOCK = XX:XX
THE CLONE IS VERSION VX.X.X
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
6. When Teaching is done, disconnect the MPI cable from the Target TV,
turn OFF the TV, and unplug the TV power cord for 15 seconds.
7. Reconnect the TV power cord, and turn ON the TV. The Master TV
Setup should be resident on the Target TV.
206-4186
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target
TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are
not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of
these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).
LT2002 Cloning Notes
• Read the IMPORTANT CLONING
INFORMATION on page 23 before
beginning any cloning procedures.
MPI
Cable
Antenna
or CATV
• A slow flashing green light indicates
that there are communication
problems between the TV and the
LT2002. If this is the case, check for
a damaged cable, poor contacts, or
other connection troubles.
Ferrite Core
(TDK, ZCAT
2035-0930)
Connect cable to
TV MPI Jack and
follow on screen
instructions
Status
Indicator
MPI
Reset
Color
•
•
green
red
battery ok
battery low
Blink pattern
power on
no communications
•
•
slow
• If the status indicator is red, the
LT2002 batteries are low and should
be replaced. Install four (4) high-
quality alkaline AA batteries.
heartbeat power on
communications ok
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION
THE SW IS REVISION
XX
XX
CLONE CLOCK
TV CLOCK
=
=
XX:XX
XX:XX
®
- PRESS ANY KEY TO CONTINUE.
QuickSet II Programmer
• Learning and Teaching is only
possible between identical model TVs;
however, the LT2002 can store up to
three different Master TV Setups.
- DISCONNECT CLONE WHEN DONE.
LT2002
LT2002 Clone
Programmer
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
Learn Setup from Master TV
1. Ensure the Master TV is set up completely and in Pass-through Mode.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
2. Tune/set the TV to an analog channel or Aux input, and then plug one end
of the MPI cable into the TV MPI port.
3. If there is a good connection after the LT2002 is connected to the TV MPI
port, “THE CLONE HAS CONTROL OF THE TV” message will appear
on the TV screen. Press any key on the Installer Remote to access the
LT2002 Clone Selection Menu.
(6) DISPLAY CLONE SETUP
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
4. Press 1 on the Installer Remote to select LEARN FROM TV from the
Clone Selection Menu; then press ENTER to proceed to the Memory Bank
Selection Menu.
SAVE TV SETUP IN SELECTED
CLONE MEMORY
5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in
which to store the Master Setup. Then, press ENTER.
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
Note: If you choose a Memory Bank that already has a Master device’s
setup programmed into it, that setup will be overwritten by the new Master
TV Setup.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
6. Verify the Learning setup information on the next screen, and then press
POWER to transfer the Master TV Setup into the selected Memory Bank
on the LT2002.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
(Continued on next page)
28
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.)
(Continued from previous page)
Learning usually takes about 90 seconds. “LEARNING IN PROGRESS”
will be displayed on the screen while the LT2002 copies the Master Setup.
When the Learning process is complete, a “LEARNING COMPLETE”
message will be displayed.
7. When Learning is complete, disconnect the MPI cable from the Master TV.
(Optional) Set the Clock
Set the time on a Master TV’s clock. (If the time has already been copied from a
TV into the LT2002 clone programmer, you can set the Master TV’s clock by
copying the time from the clone programmer.) The LT2002 can copy the current
time to both a Master TV and to the clone’s internal clock—accurate to within
one minute. (Another reason that the LT2002 should be equipped with fresh,
high-quality alkaline batteries, is for it to keep the time as accurately as possible.)
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
Since the LT2002’s time cannot be set directly, the current time needs to be
copied from an LG TV equipped with an enabled MPI port.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
After the time is copied to the LT2002 clone programmer, the current time will
be maintained and can then be transferred to another TV. (This can be a
Master TV or another TV which has already had the features set up.)
Teach Master TV Setup to Target TV
1. Ensure the Target TV is in Pass-through Mode, and then use the Installer
Remote to enter the Target TV Installer Menu: Press MENU repeatedly until
the on-screen display of the TV setup menus no longer toggles, and then
press 9-8-7-6 + ENTER.
CLONE SELECTION MENU
2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER.
When the value changes back to 0, press ENTER again to exit the Installer
Menu.
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
3. Tune/set the TV to an analog channel or Aux input (ideally the same source
tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and
then connect the MPI cable to the MPI port on the Target TV.
(6) DISPLAY CLONE SETUP
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
4. With “THE CLONE HAS CONTROL OF TV” message on display, press 2
on the Installer Remote to select TEACH TO TV from the LT2002 Clone
Selection Menu. Then, press ENTER.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
COPY SELECTED CLONE MEMORY
TO TV
5. Select the LT2002 Memory Bank in which the new Master TV Setup is
located, and press ENTER.
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
6. Verify the Teaching setup information on the next screen, and then press
POWER to transfer the Master TV Setup to the Target TV.
Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will
be displayed on-screen during Teaching. When the Teaching process is
complete, a “TEACHING COMPLETE” message will be displayed.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
7. When Teaching is done, disconnect the MPI cable from the Target TV, turn
OFF the TV, and unplug the TV power cord for 15 seconds.
8. Reconnect the TV power cord, and turn ON the TV. The Master TV Setup
should be resident on the Target TV.
206-4186
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode of Operation Overview
FTG Mode via CPU or EBL
FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels.
As indicated in the introduction to this document, there are two separate and distinct methods for
configuring LD320H/LD325H and LD340H/LD345H TVs for FTG Mode of operation: one (new) method is
to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG
Mode operation. FROM A LOCAL CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS
MUTUALLY EXCLUSIVE. IF THE CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG
MODE. LIKEWISE, IF THE EBL IS IN FTG MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE.
Note: LD320H/LD325H TVs must have the following minimum software loads in order to support FTG
Mode via CPU: CPU version 3.61 or later and PTC version 1.01.008 or later. If necessary, contact LG to
obtain LD320H/LD325H CPU and PTC software files, and perform the software updates as described in
Reference section, “Upgrading TV/PTC Software using a USB Memory Device.” If a Pro:Centric server is
installed in the institution head end, you will also have the option to remotely reconfigure LD320H/LD325H
TVs that are currently in FTG Mode via EBL for FTG Mode via CPU. Refer to the Pro:Centric™ Server
Admin Client User Guide for further information.
Both FTG Mode via CPU and FTG Mode via EBL provide the following features:
• Logical channels mapped to either RF delivered content.
• Digital RF channel minor (program) numbers up to 255.
• FTG Channel Map of up to 141 logical channels.
• Start Channel set for RF or Aux input delivered content.
• Pro:Centric data delivery over RF.
In addition, both FTG Mode via CPU and FTG Mode via EBL require LG FTG Device Configuration
Application PC software to create an FMA Configuration (.fma) file. However, the configuration processes
then diverge as follows:
FTG Mode via CPU
FTG Mode via EBL
In this mode, the CPU is the owner of the FTG Channel
Map and must be configured with an FTG Channel Map
and FTG Installer Menu settings using one of the following
processes:
In this mode, the EBL is the owner of the FTG Channel
Map and must be configured with an FTG Channel Map
and FTG Installer Menu settings using one of the following
processes:
• Local: Configure an individual LD320H/LD325H or
LD340H/LD345H TV via its USB port using an FMA
Configuration (.fma) file on a USB memory device. The
“Teach to TV (FMA)” process, along with associated
procedures, is described on pages 32 to 35.
• Local: Configure an individual LD320H/LD325H or
LD340H/LD345H TV’s EBL via its TV-LINK CFG jack
using a direct PC-to-TV connection and the FTG Device
Configuration Application. The “Write” process for an
FTG Channel Map and FTG Installer Menu settings is
described on page 36.
• Remote: Configure all LD320H/LD325H or LD340H/
LD345H TVs at the site using a Pro:Centric server head
end device (Example: PCS150R). Load an FMA Configu-
ration (.fma) file on the Pro:Centric server using the TV
E-Z Installation “Configuration” option in the Pro:Centric
Server Admin Client. Refer to the Pro:Centric™ Server
Admin Client User Guide for further information.
• Remote: Configure all LD320H/LD325H or LD340H/
LD345H TV EBLs at the site using a Free-To-Guest Man-
agement Appliance (FMA) head end device (Example:
FMA-LG101). Refer to the Free-To-Guest (FTG) Con-
figuration Application manual and/or the Installation &
Setup manual for the FMA device for further information.
30
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode of Operation Overview (Cont.)
While the TV is in FTG Mode:
• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu
items will be read-only.
• Any FTG configuration changes must be made using the FTG Device Configuration Application. FTG
Channel Map Configuration and FTG Installer Menu Configuration Utilities enable you to make changes,
respectively, to the FTG Channel Map and FTG Installer Menu settings as necessary. Based on the initial
method used to configure the TV for FTG Mode operation (via CPU or EBL), all subsequent changes
must be transferred to either the TV or the EBL via a process that is in accordance or compatible with that
method (see information on local configuration in this document or refer to documentation for the head
end device/server for information on remote management).
• If it becomes necessary to reset the TV to Pass-through Mode, there are several options that will enable
you to do so. Refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information.
Pages 37 to 40 provide overviews of the FTG Channel Map, FTG Installer Menu, and FMA Configuration
Utilities that comprise the FTG Device Configuration Application. Refer to the Free-To-Guest (FTG)
Configuration Application manual for further information on the FTG Device Configuration Application.
Determining the TV Operating Mode
To determine the operating mode of the TV, press MENU on the Installer Remote. The menu display
alternates based on the operating mode. See examples below.
If the end user Function Menu appears, typically the TV is in FTG Mode. If the TV setup menus appear,
the TV is in Pass-through Mode.
Move
Enter
ASPECT RATIO
Function Menu
Set By Program
4:3
ABC
Indicates the TV (CPU or EBL) is not
in Pass-through Mode. While the TV is
in FTG Mode, Installer Menu settings
can be accessed as read-only.
16:9
Zoom
Just Scan
TV Setup Menus
CHANNEL
Shows that the TV is in
Pass-through Mode.
PICTURE
OPTION
TIME
AUDIO
LOCK
INPUT
MY MEDIA
206-4186
31
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU
Creating an FMA Configuration File using the FTG Device Configuration Application
This section describes how to create an FMA Configuration (.fma) file that can be saved to a USB
memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FMA
Configuration file using the FTG Device Configuration Application. However, if you do not know the RF
channels at the site, there is an option to save (Learn) an FMA Configuration file from a TV (see
“
Learning an FMA Configuration File from a TV” on page 34).
The procedure below provides an overview of the steps required to create an FMA Configuration file.
Refer to the Free-To-Guest (FTG) Configuration Application manual for further information. See also
FTG Device Configuration Application sample screens on pages 37 to 40.
FTGsoftware.
1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the
PC that will be used to create the FMA Configuration file.
2. Either:
• Open an existing FTG Configuration (.rml) file, if applicable, to use its FTG Channel Map and/or FTG
Installer Menu settings. Otherwise, create a new FTG Channel Map using the FTG Channel Map
Editor in the FTG Channel Map Configuration Utility. Then, continue with step 3.
Note: Up to 141 logical channels can be defined in the FTG Channel Map.
• To view and/or base a new FMA Configuration file on an existing LD320H/LD325H or LD340H/LD345H
FMA Configuration file, click Configure in the FTG Device Configuration Application menu bar, and
select FMA to access the FMA Configuration Utility. Then, click the Open button above the FMA
Configuration List, and double-click the desired (.fma) file. A list of the file’s contents will be displayed
in the FMA Configuration List window, and you can edit the FMA Configuration List as necessary to
create a new file. Proceed to step 4 when you are ready to continue.
3. Click Configure in the FTG Device Configuration Application menu bar, and select FMA to access the
FMA Configuration Utility.
4. To add an FTG Channel Map, click >> under FTG Channel Map to copy the current FTG Channel
Map to the FMA Configuration List.
Note: If you make any change(s) in the FTG Channel Map Configuration Utility to the current data to
be included in the FMA Configuration List, you will need to recopy the FTG Channel Map to the FMA
Configuration List.
5. (Optional) Load default Installer Menu settings for the TV:
• Click the down arrow at the right of the Chassis field under Installer Menu Templates, and select the
appropriate option (depending on the TV type) from the drop-down list of available models.
• Click the Load button.
• Use the FTG Installer Menu Configuration Utility to modify settings, if necessary. Then, return to the
FMA Configuration Utility.
6. To add FTG Installer Menu settings, click >> under FTG Installer Menu Settings to copy the current
settings to the FMA Configuration List.
Note: If you make any change(s) in the FTG Installer Menu Configuration Utility to the current data to
be included in the FMA Configuration List, you will need to recopy the FTG Installer Menu settings to
the FMA Configuration List.
(Continued on next page)
32
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
(Continued from previous page)
7. Click the Save button above the FMA Configuration List to save its contents to an FMA Configuration
(.fma) file on the PC’s hard drive for later use (default folder path is C:\Program Files\Zenith\Widget\
FMA).
8. Transfer the FMA Configuration file to a USB memory device, and proceed to “Teaching FMA
Configuration to a TV” below to transfer the FMA Configuration file to an LD320H/LD325H or LD340H/
LD345H TV.
Teaching FMA Configuration to a TV
This procedure describes how to “Teach” an FMA Configuration file from a USB memory device to a TV.
Ensure you have completed the procedure above to create the FMA Configuration file before proceeding
with the steps below.
Note: If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the FTG
Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV connection as described
on page 36 or an FMA head end device to reconfigure the EBL.
Note: If you wish to switch the TV from FTG Mode via EBL to FTG Mode via CPU, refer to Reference
section, “Resetting Factory Defaults on the TV(s),” for further information before proceeding.
1. Plug the USB memory device that contains the FMA Configuration
USB Download Menu
file into the Target LD320H/LD325H or LD340H/LD345H TV USB IN
port.
Upgrade TV Software
2. Press MENU on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is
already in FTG Mode).
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (FMA)
3. Use the arrow navigation keys to select/highlight either the Option
menu icon from the TV setup menus or the Lock menu icon from
the Function Menu. Then, press the number “7” key a total of seven
times to display the USB Download Menu.
Return
Enter
Teach To TV (FMA)
xx0BAL-PLAT200001.FMA
4. Use the Up/Down arrow keys to select Teach To TV (FMA), and
then press ENTER.
5. Use the Up/Down arrow keys to select the FMA Configuration file
Return
Enter
you want to install, and then press ENTER.
The TV will show Teaching completion progress in a new window.
Do NOT remove the USB device until Teaching is complete. When
Teaching is complete, the TV will tune to the first logical channel in
the FTG Channel Map.
Teach To TV
!
UPDATING...
50%
6. When Teaching is done, remove the USB memory device. The
FMA Configuration should be resident on the Target TV. Also, the
Target TV CPU is now in FTG Mode (if it was previously in Pass-
through Mode).
Do not unplug!
206-4186
33
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
Learning an FMA Configuration File from a TV
To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FMA Configuration
file using the FTG Device Configuration Application as described on pages 32 to 33. However, if necessary,
this option enables you to save (Learn) an FMA Configuration file from an LD320H/LD325H or LD340H/
LD345H TV to a USB memory device.
Note: If the TV is NOT already in FTG Mode, you may need to perform some manual configuration on
the TV before you start this procedure (see “Optional Manual Configuration / TV Setup” on following
page).
USB Download Menu
1. Plug a USB memory device into the USB IN port on the TV.
2. Press MENU on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is
already in FTG Mode).
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (FMA)
Learn From TV (TLL)
Learn From TV (FMA)
3. Use the arrow navigation keys to select/highlight either the Option
menu icon from the TV setup menus or the Lock menu icon from
the Function Menu. Then, press the number “7” key a total of seven
times to display the USB Download Menu.
Return
Enter
4. To gain access to the Learn From TV options in the USB Down-
load Menu, key in the password used to enter the Installer Menu
(Example: Press 9-8-7-6).
Learn From TV (FMA)
Select the file name and press OK to start
xx0BAL-PLAT200001.FMA
5. Use the Up/Down arrow keys to select Learn From TV (FMA), and
then press ENTER.
6. To differentiate this .fma file from others, you can use the Up/Down
arrow keys to change the last five digits of the filename. Press
ENTER when you are ready to initiate Learning.
Return
Enter
Learn From TV
25%
!
The TV will show Learning completion progress in a new window.
Do NOT remove the USB device until Learning is complete. When
Learning is complete, the USB Download Menu will reappear on
screen.
UPDATING...
Do not unplug!
7. When you are finished, remove the USB memory device.
Note: It is highly recommended that you open this FMA Configuration
file in the FTG Device Configuration Application—BEFORE transferring
(Teaching) the file to any TVs—to verify FTG Channel Map and FTG
Installer Menu settings and enable Pro:Idiom decryption by marking
Encrypted channels. This will also enable you to confirm and add
channel attributes, labels, etc.
34
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
Optional Manual Configuration / TV Setup
The manual configuration procedures below should only be performed if you do not know the RF channels
at the site and need to “Learn” an FMA Configuration file from an LD320H/LD325H or LD340H/LD345H TV
as described on the previous page. Ensure the TV is in Pass-through Mode before you begin.
Set Installer Menu Items
xxLD340H PTC INSTALLER MENU
These steps provide specific instruction only on the Installer Menu items
that should be set on an LD320H/LD325H or LD340H/LD345H TV. Refer to
pages 15 to 21 for detailed information on all Installer Menu items.
000 INSTALLER SEQ
000
1. Make sure the TV is ON. Then, use the Installer Remote to enter the
Installer Menu: Press MENU repeatedly until the on-screen display of the
TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.
UPN 000-000-000-000
PTC V1.00.001
ASIC 20E7
CPU V3.25.00
2. Set Installer Menu item 117 FACT DEFAULT to 001 and press ENTER
on the Installer Remote.
This clears all Installer Menu custom settings, the channel lineup, etc.
and reloads the factory default settings. The value will change back to
0 after the commercial controller (PTC) has been restored to factory
default condition. This step ensures that the TV Channel Memory will be
the active channel lineup.
Typical Installer Menu
Note: The Installer Menu header will vary
depending on the TV you are setting up.
117 FACT DEFAULT
003 BAND/AFC
001
00X
3. Set Installer Menu item 003 BAND/AFC, as appropriate.
• Broadcast: Set to 000.
• HRC: Set to 002.
• IRC: Set to 003.
• CATV: Set to 001 (default).
Adjust the settings for these
Installer Menu items.
4. Set any other Installer Menu items that affect your TV programming
network to the required configuration. For example, enable/disable Aux
inputs, set a Start Channel, etc.
5. After you have adjusted all required Installer Menu item settings, press
ENTER once on the Installer Remote to save your changes; then, press
ENTER again to exit the menu.
Move
Enter
CHANNEL
Auto Tuning
Manual Tuning
Channel Edit
Channel Label
Run Auto Tuning (Channel Search)
Note: In the FMA Configuration file, Logical Channel numbers will automati-
cally be assigned in ascending order, starting with 0 (zero), to the Physical
Channels from the TV Channel Map.
Note: Pro:Idiom decryption for encrypted channels will not be enabled unless
you use the FTG Device Configuration Application to set channel attributes.
Use Channel Menu options to run
Auto Tuning and edit the channel
lineup, as necessary.
1. Search for all available analog and digital channels: Use the Installer
Remote to go to the Channel Menu, select the Auto Tuning option, and
follow the on-screen instructions.
2. Use the Channel Edit option in the Channel Menu to edit the channel
lineup, as necessary, to include free to guest channels only. Add/delete
channels per your system requirements.
Once you have completed these procedures, return to “Learning an FMA
Configuration File from a TV” on the previous page to complete the Learn
sequence.
206-4186
35
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via EBL
The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV connection.
Refer to the Free-To-Guest (FTG) Configuration Application manual for further information. See also FTG
Device Configuration Application sample screens on pages 37 to 40.
FTGsoftware.
• If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the
FTG Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes
described on pages 32 and 33 to reconfigure the TV CPU.
• If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer
to Reference section, “Resetting Factory Defaults on the TV(s),” for further information before
proceeding.
Rear Jack Panel
1. Install (if necessary) and launch the FTG Device
Configuration Application (v5.0.0 or higher) on the
PC that will be used to configure the EBL.
ANTENNA IN
RS-232C IN
(SERVICE ONLY)
2. Build an FTG Channel Map using the FTG Channel
Map Editor in the FTG Channel Map Configuration
Utility (or, if applicable, open an existing FTG
Configuration [.rml] file).
.....
....
REMOTE
CONTROL
OUT
AV IN 1
L/MONO-AUDIO-R
VIDEO
GAME
AUDIO IN
(RGB/DVI)
CONTROL/
MPI
TV-LINK
CFG
Note: Up to 141 logical channels can be defined in the
FTG Channel Map.
PB
PR
R
Y
L
AUDIO
VIDEO
COMPONENT IN
3. Connect the PC to the TV-LINK CFG jack on the TV’s
rear connections panel using a USB-to-TTL serial
cable (TTL-232R-5V-AJ). If necessary, install the
device driver on the PC.
TV-LINK CFG
Use for direct PC-to-TV
FTG configuration.
4. Turn ON the TV.
Note: If Installer Menu item 118 POWER SAVINGS is
set to 3 (default), the TV must be ON in order for steps
5 and 6 below to be successful.
5. “Write” the FTG Channel Map to the EBL (switches the
EBL from Pass-through Mode to FTG Mode).
Note: After a “Write” of new data, the TV will briefly
display a green text banner that shows the EBL firm-
ware version and release date.
Laptop
PC
6. “Read” the current FTG Installer Menu settings from
the EBL using the FTG Installer Menu Configuration
Utility. If necessary to make changes to Installer Menu
items, “Write” them back to the EBL in FTG Mode.
USB-to-TTL Serial Cable
Required for direct PC-to-TV
FTG configuration.
7. Save the FTG Channel Map and FTG Installer Menu
settings to an FTG Configuration (.rml) file for future
use.
Notes:
• ANTENNA IN connector located on jack panel on
26LD320H, 26LD340H, and 26LD345H only.
8. Tune the TV to a Logical Channel in the FTG Channel
Map.
• Dual-purpose GAME CONTROL/MPI port on
26LD320H and LD340H/LD345H TVs only. On
32/37/42LD320H and 32/37LD325H TVs, the MPI port
is located on the same plate as the RF Antenna jack.
36
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Device Configuration Application Utilities Overview
FTG Channel Map Configuration Utility
The FTG Channel Map Configuration Utility enables you to build a Channel Map with logical channel
numbers.
Note: Write, Read, and Learn functions in the FTG Channel Map Configuration Utility are used for direct
PC-to-TV FTG configuration of LD320H/LD325H and LD340H/LD345H TVs (FTG Mode via EBL). These
functions are not applicable to the process of creating an FMA Configuration file to be saved to a USB
memory device (FTG Mode via CPU).
Filename of opened FTG
Configuration (.rml) file.
LEARN
Click to transfer the TV Channel Map from
the PTC to the EBL and the FTG Device
Configuration Application. (Requires that
2-5-5 + MENU was performed to transfer
TV Channel Map to PTC.)*
PRINT MAP
Click to display a printable
FTG Channel Map Report. The
report can also be exported as
an HTML or Text file.
READ
Click to transfer the FTG Channel
Map from the EBL to the FTG Device
Configuration Application.
EDIT/ADD MAP
Click to open the FTG Channel Map
Editor to create or edit an FTG
Channel Map (see next page).
WRITE
Click to transfer the FTG Channel
Map to the EBL. This will switch the
EBL from Pass-through Mode to
FTG Mode.
* Logical Channel numbers will automatically be assigned in ascending order,
starting with 0 (zero), to the Physical Channels from the TV Channel Map.
206-4186
37
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Device Configuration Application Utilities Overview (Cont.)
FTG Channel Map Editor
The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map.
LOGICAL CHANNEL MAPPING
CUSTOM CHANNEL LABELS/ICONS
Enter custom labels and select icons by
name on menu or by number.
SET CHANNEL ATTRIBUTES
Check/select Encrypted, OSD,
or Blank Video.
Select a Logical Channel number, then
assign it the RF, Major, and Minor chan-
nel numbers to complete the mapping.
EXIT
Click to exit editor and
return to FTG Channel
DELETE
Click to remove highlighted
channel from FTG Channel
Map.
Map Configuration Utility.
ADD
After defining a new Logical
Channel, click to add channel
to the FTG Channel Map.
UPDATE
After editing an existing
Logical Channel’s data, click
to commit the changes in the
FTG Channel Map.
38
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Device Configuration Application Utilities Overview (Cont.)
FTG Installer Menu Configuration Utility
Note: Write, Read, Learn, and IR Remote Access functions in the FTG Installer Menu Configuration
Utility are used for direct PC-to-TV FTG configuration of LD320H/LD325H and LD340H/LD345H TVs
(FTG Mode via EBL). These functions are not applicable to the process of creating an FMA Configuration
file to be saved to a USB memory device (FTG Mode via CPU).
CONFIGURATION SETTINGS
Select tabs for categories of Installer
Menu items to set up TV.
HOSPITAL-GRADE TV ONLY
Set Hospital items on Installer Menu
for hospital-grade TV models.
Filename of opened FTG
Configuration (.rml) file.
LEARN
Click to transfer Installer Menu settings
from the PTC to the EBL and FTG
Device Configuration Application.*
INSTALLER DEFAULTS
Click to reset FTG Installer Menu
items shown in the FTG Device
Configuration Application to defaults.
READ
Click to transfer the Installer Menu
settings in the EBL to the FTG
Device Configuration Application.
IR REMOTE ACCESS
Toggle IR Remote Access to ON to
obtain access to TV setup menus
and Installer Menu.
* Logical Channel numbers will automatically be
assigned in ascending order, starting with 0 (zero), to
the Physical Channels from the TV Channel Map.
WRITE
Click to transfer the FTG Installer
Menu settings to the EBL.
206-4186
39
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Device Configuration Application Utilities Overview (Cont.)
FMA Configuration Utility
Note: FMA Write, Read, Clock, Broadcast, Firmware, and IP Communication functions in the FMA
Configuration Utility are used to configure b-LAN enabled equipment (Example: FMA-LG101) at the hotel/
institution head end. These functions are not applicable to the process of creating an FMA Configuration file
to be used with LD320H/LD325H and LD340H/LD345H TVs (FTG Mode via CPU).
FMA CONFIGURATION LIST
(data to be saved or already
NEW/OPEN/SAVE
saved in FMA Configuration file)
FMA File options
Filename of opened FTG
Configuration (.rml) file.
Copy FTG Channel Map
to and from FMA
Configuration List.
Copy FTG Installer Menu
settings to and from FMA
Configuration List.
Load default FTG Installer
Menu for LD320H/LD325H
or LD340H/LD345H.
Note: The data referenced in the FMA Configuration List is only a snap-
shot of the current FTG Channel Map and FTG Installer Menu settings
when copied to the list. If you make any change(s) to the current data
to be included in the FMA Configuration List, you will need to recopy
Channel Map and Installer Menu settings to the FMA Configuration List.
40
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Jack Pack / TV Connections & Setup
Remote Jack Pack Setup
RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093
RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE
to 001). See Installer Menu detailed descriptions for further information.
093 RJP AVAILABLE
001
TV Connections
Make these connections ONLY after Master TV Setup and TV cloning procedures are
complete.
Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP
INTERFACE port on the TV’s jack panel. Then, connect HDMI, RGB, and Composite Video/Audio
connectors, as applicable, for the cable bundle.
AUDIO/VIDEO IN 1
Connect Composite Video/
RJP
Connect RJ-45 Control cable
from RJP cable bundle.
Audio connectors from RJP
cable bundle. (Composite
Video on legacy RJP only.)
ANTENNA IN
RS-232C IN
(SERVICE ONLY)
.....
RESET UPDATE
RJP
....
REMOTE
CONTROL
OUT
..........
AV IN 1
HDMI
2
L/MONO-AUDIO-R
VIDEO
GAME
AUDIO IN
(RGB/DVI)
CONTROL/
MPI
.....
.....
.....
HDMI
/DVI IN
..........
1
TV-LINK
CFG
RGB IN (PC)
SPEAKER
(
)
OUT
8
PB
PR
R
Y
L
AUDIO
VIDEO
COMPONENT IN
RGB IN (PC)
Connect RGB connector from RJP
cable bundle (legacy RJP only).
HDMI/DVI IN 1
Connect HDMI connector
from RJP cable bundle.
Notes:
• ANTENNA IN connector located on jack panel on 26LD320H, 26LD340H, and 26LD345H only.
• Dual-purpose GAME CONTROL/MPI port on 26LD320H and LD340H/LD345H TVs only. On
32/37/42LD320H and 32/37LD325H TVs, the MPI port is located on the same plate as the RF
Antenna jack.
206-4186
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Upgrading TV/PTC Software using a USB Memory Device
Checking the Software Versions
xxLD340H PTC INSTALLER MENU
You can check the software versions of the TV by
Typical Installer
Menu
accessing the Installer Menu with the Installer
Remote: Press MENU repeatedly until the on-screen
menu display no longer toggles, and then press
9-8-7-6 + ENTER.
000 INSTALLER SEQ
000
UPN 000-000-000-000
PTC V1.00.001
ASIC 20E7
CPU V3.25.00
When you are finished, press ENTER again to exit
the Installer Menu.
PTC Version
CPU Version
Upgrading TV/PTC Software
Before you begin, note that the software upgrade files must be stored in a folder
named “LG_DTV” in the root directory of the USB memory device. Also, ensure
the USB device has been formatted with FAT format.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Note for TV Software Upgrade only: If the TV detects a later version of software
on the USB device, it will automatically display a dialog from which you can start the
software upgrade immediately. Otherwise, you can close the dialog, and access the
USB Download Menu as described below.
Teach To TV (FMA)
Return
Enter
1. Turn the TV ON.
TV Software Update (Expert)
2. Plug the USB memory device into the USB IN port on the TV.
3. Press MENU on the Installer Remote to display the TV setup menus (TV is in
Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).
4. Use the arrow navigation keys to select/highlight either the Option menu icon
from the TV setup menus or the Lock menu icon from the Function Menu.
Then, press the number “7” key a total of seven times to display the USB
Download Menu.
TV Software Update
LOGO Image Download
5. Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade
PTC Software, as applicable, and press ENTER.
6. Select the appropriate option(s), depending on the type of upgrade:
TV Software Update (Expert)
• TV Software Upgrade: (See screen samples at right.) Select TV Software
Update from the first TV Software Update window. In the second TV Software
Update window, select/highlight the update file to install and press ENTER.
[ Current TV Software Version Information ]
EPK : 03.03.00
The following software files are found in the memory card.
Select the file you want to download to this TV
or press EXIT to cancel the update.
Note: Do not select Forced Update options unless you have been specifically
instructed to do so or have previous experience with Expert Software Updates.
EPK : 03.05.00
• PTC Software Upgrade: In the PTC Software Update window, select/highlight
the update file to install and press ENTER.
[ Forced Update Option ]
Ext. MICOM
LOGO Image
SPI Boot
Note: The PTC Software Update window is similar to the second TV Soft-
ware Update window, though there are no Forced Update options. Current
software version information is shown at the top and update files on the USB
device are listed at the bottom of the window.
xxLD340H_v1_00_RevNo1000_USB
The TV will show update completion progress in a new window. Do NOT remove the USB device
until the software upgrade is complete. When a TV software upgrade is complete, the TV will reset
itself with an automatic restart. When a PTC upgrade is complete, the TV will turn OFF.
42
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Downloading a Splash Screen using a USB Memory Device
Splash Screen Image File Guidelines
USB Download Menu
• The splash screen image must be a baseline (not progressive) JPEG.
Upgrade TV Software
Upgrade PTC Software
• The image should be no larger than 1 MB.
Teach To TV (TLL)
• The ideal size for the image is 1366 x 768 pixels or under.
Teach To TV (FMA)
• The image file must be stored in a folder named “LG_DTV” in the root
Return
Enter
directory of USB memory device.
• Ensure the USB device has been formatted with FAT format.
TV Software Update (Expert)
Downloading a Splash Screen Image
1. Turn the TV ON.
2. Plug the USB memory device into the USB IN port on the TV.
3. Press MENU on the Installer Remote to display the TV setup menus (TV is in
Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).
TV Software Update
4. Use the arrow navigation keys to select/highlight either the Option menu icon
from the TV setup menus or the Lock menu icon from the Function Menu.
Then, press the number “7” key a total of seven times to display the USB
Download Menu.
LOGO Image Download
TV Software Update (Expert)
5. Use the Up/Down arrow keys to select Upgrade TV Software, and then press
ENTER.
The following software files are found in the memory card.
Select the file you want to download to this TV
or press EXIT to cancel the update.
6. Select LOGO Image Download from the first TV Software Update window.
7. In the second TV Software Update window, use the Up/Down arrow keys to
select the image file to download, and then press ENTER.
The TV will show download completion progress in a new window. Do NOT
remove the USB device until the image download is complete. When the image
download is complete, the TV will reset itself with an automatic restart. Upon the
restart, you should see the new splash screen.
Splash Image 1366 X 768 ProCentric
206-4186
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Power Consumption Settings
26/32/37/42LD320H & 32/37LD325H
The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 003 (default) and
Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100).
26LD320H
Power
Consumption
(Watts)
32LD320H / 32LD325H
37LD320H / 37LD325H
42LD320H
Power
Consumption
(Watts)
Item 099
Back Lighting
(Static)
Power
Percent
Power
Percent
Percent
Savings
Percent
Savings
Consumption
Savings
Consumption
Savings
(Watts)
(Watts)
100
90
80
70
60
50
40
30
20
10
1
56.82
51.98
47.09
42.06
39.71
37.36
36.31
35.12
32.59
30.23
27.95
0.00%
8.52%
72.97
63.82
58.53
53.58
44.24
41.27
38.71
36.20
33.51
31.01
28.55
0.00%
12.54%
19.78%
26.57%
39.38%
43.45%
46.95%
50.39%
54.07%
57.51%
60.87%
88.92
84.19
77.84
72.19
66.28
60.90
56.58
52.35
47.75
43.68
39.62
0.00%
5.32%
107.53
86.68
78.79
72.81
66.78
60.61
56.35
52.90
47.71
43.04
38.86
0.00%
19.39%
26.73%
32.29%
37.89%
43.63%
47.60%
50.81%
55.63%
59.98%
63.86%
17.13%
25.97%
30.12%
34.25%
36.10%
38.19%
42.64%
46.80%
50.82%
12.46%
18.81%
25.46%
31.51%
36.37%
41.13%
46.30%
50.88%
55.44%
26LD320H
32LD320H / 32LD325H
37LD320H / 37LD325H
42LD320H
Item 099
Back Lighting
(Dynamic)
Power
Consumption
(Watts)
Power
Percent
Power
Percent
Power
Consumption
(Watts)
Percent
Savings
Percent
Savings
Consumption
Savings
Consumption
Savings
(Watts)
(Watts)
200
190
180
170
160
150
140
130
120
110
101
72.19
68.21
63.72
59.21
55.04
50.81
46.03
41.49
36.32
31.52
26.95
0.00%
5.51%
75.45
69.23
65.26
60.72
56.29
51.82
46.62
41.67
36.14
31.11
26.41
0.00%
8.25%
110.86
99.05
92.33
85.39
78.61
71.70
63.53
55.65
47.34
39.90
33.00
0.00%
10.65%
16.72%
22.98%
29.10%
35.32%
42.69%
49.80%
57.30%
64.01%
70.24%
125.41
111.41
103.30
95.29
87.64
79.71
70.73
61.80
51.86
42.90
34.52
0.00%
11.16%
17.63%
24.02%
30.11%
36.44%
43.60%
50.72%
58.65%
65.79%
72.47%
11.74%
17.99%
23.76%
29.62%
36.24%
42.53%
49.69%
56.34%
62.67%
13.51%
19.53%
25.40%
31.33%
38.21%
44.78%
52.10%
58.76%
65.00%
Note: Values are results of controlled experiments under laboratory conditions.
44
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Power Consumption Settings (Cont.)
26/32/37/42LD340H & 26/32/37/42LD345H
26LD340H / 26LD345H
32LD340H / 32LD345H
37LD340H / 37LD345H
42LD340H / 42LD345H
Item 099
Back Lighting
(Static)
Power
Percent
Power
Percent
Power
Percent
Power
Percent
Consumption
Savings
Consumption
Savings
Consumption
Savings
Consumption
Savings
(Watts)
(Watts)
(Watts)
(Watts)
100
90
80
70
60
50
40
30
20
10
1
56.82
51.98
47.09
42.06
39.71
37.36
36.31
35.12
32.59
30.23
27.95
0.00%
8.52%
72.97
63.82
58.53
53.58
44.24
41.27
38.71
36.20
33.51
31.01
28.55
0.00%
12.54%
19.78%
26.57%
39.38%
43.45%
46.95%
50.39%
54.07%
57.51%
60.87%
88.92
84.19
77.84
72.19
66.28
60.90
56.58
52.35
47.75
43.68
39.62
0.00%
5.32%
107.53
86.68
78.79
72.81
66.78
60.61
56.35
52.90
47.71
43.04
38.86
0.00%
19.39%
26.73%
32.29%
37.89%
43.63%
47.60%
50.81%
55.63%
59.98%
63.86%
17.13%
25.97%
30.12%
34.25%
36.10%
38.19%
42.64%
46.80%
50.82%
12.46%
18.81%
25.46%
31.51%
36.37%
41.13%
46.30%
50.88%
55.44%
26LD340H / 26LD345H
32LD340H / 32LD345H
37LD340H / 37LD345H
42LD340H / 42LD345H
Item 099
Back Lighting
(Dynamic)
Power
Percent
Power
Percent
Power
Percent
Power
Percent
Consumption
Savings
Consumption
Savings
Consumption
Savings
Consumption
Savings
(Watts)
(Watts)
(Watts)
(Watts)
200
190
180
170
160
150
140
130
120
110
101
72.19
68.21
63.72
59.21
55.04
50.81
46.03
41.49
36.32
31.52
26.95
0.00%
5.51%
75.45
69.23
65.26
60.72
56.29
51.82
46.62
41.67
36.14
31.11
26.41
0.00%
8.25%
110.86
99.05
92.33
85.39
78.61
71.70
63.53
55.65
47.34
39.90
33.00
0.00%
10.65%
16.72%
22.98%
29.10%
35.32%
42.69%
49.80%
57.30%
64.01%
70.24%
125.41
111.41
103.30
95.29
87.64
79.71
70.73
61.80
51.86
42.90
34.52
0.00%
11.16%
17.63%
24.02%
30.11%
36.44%
43.60%
50.72%
58.65%
65.79%
72.47%
11.74%
17.99%
23.76%
29.62%
36.24%
42.53%
49.69%
56.34%
62.67%
13.51%
19.53%
25.40%
31.33%
38.21%
44.78%
52.10%
58.76%
65.00%
Note: Values are results of controlled experiments under laboratory conditions.
206-4186
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: TV Camport Auto Sense Operation
The Camport Auto Sense function is enabled when:
1. Installer Menu item 034 CAMPORT EN is set to 1 AND
2. Installer Menu item 040 AUTO CAMPORT is enabled (1).
CAMPORT (Side Video) Functionality Control
Item 034
Item 040
Side (AV IN 2)
CAMPORT EN
AUTO CAMPORT
Video Operation
0
0
1
1
0
1
0
1
Disabled
Disabled
Selectable: Can be accessed with INPUT key, direct
access, etc.
Auto Sense: TV switches to this input when connector is
inserted. The Camport (Side [AV IN 2] Video) has the
highest priority and will override any commands including
tuning to the Start Channel.
Selectable
Auto Sense
Camport Operation (Stand-alone)
Previous State
Before Inserting
CAMPORT
Operation While
CAMPORT is
Active
State Upon
Removal of
CAMPORT
When Camport Auto Sense is enabled as above, the TV
will switch from its current source to the Side (AV IN 2)
Video input whenever a plug is inserted into the AV IN 2
Video input.
Aux or RF
Channel
Previous Aux
or RF Channel
None
Aux or RF
Channel
Last Requested
Aux or RF Channel
When the video plug is removed, the TV will switch back to
the previous source that was being displayed before the
plug was inserted. However, if any direct access to an Aux
channel or RF channel is requested while the Camport is
active, then, when the video plug is removed, the TV will
switch to the last requested channel. Source changes
using any Source keys (INPUT) are ignored. Channel Up/
Down and Flashback commands are not Direct Access
tuning commands, and they are also ignored.
Direct Access
Ch Up/Down,
Flashback, and
Input Keys
Aux or RF
Channel
Previous Aux
or RF Channel
Camport Operation (FTG or PPV)
Previous State
Before Inserting
CAMPORT
Operation While
CAMPORT is
Active
State Upon
Removal of
CAMPORT
The operation will be similar to that of the Pass-through
Mode. However, when the Channel Map is maintained
external to the PTC (i.e., FTG and PPV), Channel Up/
Down or Flashback keys are sent as Direct Access tuning
commands to the PTC/TV.
Aux or RF
Channel
Previous Aux
or RF Channel
None
Aux or RF
Channel
Last Requested
Aux or RF Channel
Direct Access
Ch Up/Down,
Flashback, and
Input Keys
Aux or RF
Channel
Last Requested Aux
or RF Channel
46
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: TV Aux Input Configuration
ENABLE
MPI DATA
DATA STATUS
MPI DATA
DIRECT ACCESS
Tuning
START AUX
SOURCE
ASSIGN-
MENT
TV
STATUS TYPE
0x41 SOURCES
ENABLED (R/W)
TYPE 0xD2
CURRENT AV
SOURCE (R)
DATA STATUS
TYPE 0x0D
AUX
Installer Menu
SOURCE (R)
OLD_
OLD_
Source
Input
Source
Mode
Number
Labeling
Value
Labeling
Value
Labeling
OCV = 0 OCV = 1
130
131
90
91
Video2
(Side)
CV
34
39
CAMPORT_EN
REAR_AUX_EN
YPrPb2 EN = 1
0x01
0x02
Video Front
(Camport)
0
1
Video Front
(Camport)
0 (VIDEO)
0 (VIDEO)
2
1
Video1
(Rear)
CV
Rear Video
(Aux)
Rear Video
(Aux)
132
133
92
93
HDMI2
DTV/PC
DTV/PC
91
35
0x04 S-Video Rear
2
3
S-Video Rear 0 (VIDEO)
5
3
HDMI1/DVI
COMPPORT_EN 0x08
= 1
Front
Computer
Front
Computer
0 (VIDEO)
134
136
94
96
RGB
PC
87
38
REAR RGB EN
= 2
0x10
SVGA Rear
Computer
4
6
SVGA Rear
Computer
2
4
6
(COMPUTER)
Component
YPrPb EN
0x40
Y/UV
Component
Rear Y/PrPb
Component
Video
0 (VIDEO)
206-4186
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: b-LAN Setup & Overview
The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology
to communicate, via the institution’s RF distribution system, with the TV for configuration and control.
Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7, LMT7Z9—are NOT supported in TVs in which
b-LAN technology is already integrated.
Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and
the GAME CONTROL/MPI port (see note below). The default value is 003—the b-LAN module is only powered
when the TV is turned ON. See chart below.
Note: 26LD320H and all LD340H/LD345H TVs have a dual-purpose GAME CONTROL/MPI port on the TV rear
jack panel. On 32/37/42LD320H and 32/37LD325H TVs, the MPI port is located on the same plate as the RF
Antenna jack.
TV Power On State
TV Standby State
POWER
SAVINGS
b-LAN & GAME
CONTROL/MPI Port
Power
b-LAN & GAME
CONTROL/MPI Port
Power
001
On
Off
On
On
003 (default)
A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to
communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded
b-LAN module to receive communication from the head end device. At this point, if it is desired for the b-LAN
module to always be powered, including while the TV is in Standby, set Installer Menu item 118 POWER
SAVINGS to 001.
Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER SAVINGS to
001 so that the GAME CONTROL/MPI port circuitry is always powered.
48
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: RJP Model List and Input Auto-sensing Hierarchy
RJP Model List
Legacy Models
Scaler Models
RJP-101M
RJP-101ML
RJP-110F
RJP-110FW
RJP-110W
RJP-110WBR
RJP-110S
RJP-120G
RJP-120T
RJP-201B
RJP-202B
N/A
N/A
RJP-210F
RJP-210FW
RJP-210W
RJP-210WBR
RJP-210S
RJP-220G
RJP-220T
RJP-301B
RJP-302B
RJP Input Auto-sensing Hierarchy
Priority
Video
Audio
1st (Highest)
Digital Video In
PC Video In
Video In
Audio In (3.5mm)
Audio In (L/R)
2nd
3rd
Digital Video In
206-4186
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Resetting Factory Defaults on the TV(s)
This section describes how to reset factory defaults either on a single TV that is currently in Pass-through
Mode or on multiple TVs that are currently in FTG Mode.
Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Pass-
through Mode.
Installer Menu Item 117 FACT DEFAULT
If the TV is currently in Pass-through Mode, you can set Installer Menu item 117 FACT DEFAULT to 001 to
reload the factory defaults and clear the channel lineup, including any assigned channel icons and custom
text labels.
Factory “IN-STOP”
If the TV is currently in FTG Mode, a predefined value for Installer Menu item 117 FACT DEFAULT
enables access to initiate a factory “IN-STOP” process that will reset the TV to Pass-through Mode in
addition to restoring all factory defaults. Contact technical support for the required value for Installer Menu
item 117 and for additional information on performing the IN-STOP from the Installer Menu.
Additional FTG Mode via CPU Options
There are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG
Mode via the CPU. The first enables you to reset a single TV to Pass-through Mode, while the second
enables you to reset multiple TVs to Pass-through Mode at one time.
• Using a USB memory device, “Teach” an FMA Configuration file that only contains a “0 Mapped
Channels” FTG Channel Map to the TV. Refer to “Creating an FMA Configuration File using the FTG
Device Configuration Application” and “Teaching FMA Configuration to a TV” on pages 32 and 33,
respectively, for further information.
• If your system uses a Pro:Centric server for remote management/administration, use the Pro:Centric
Admin Client to load an FMA Configuration file that only contains a “0 Mapped Channels” FTG Channel
Map on the Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further
information.
Additional FTG Mode via EBL Options
There are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG
Mode via the EBL. The first enables you to reset a single TV to Pass-through Mode, while the second
enables you to reset multiple TVs to Pass-through Mode at one time.
Note: While the IN-STOP process described above will clear both the PTC and the CPU, both
options below only clear the PTC. Thus, the current Channel Map and TV setup menu settings
will remain in the CPU after the reset is completed.
• Using a direct PC-to-TV connection, “Write” an unpopulated Channel Map—that is, a Channel Map with
zero channels—to the TV. Refer to the “FTG Mode via EBL” procedure on page 36 and/or the Free-To-
Guest (FTG) Configuration Application manual for further information.
• If your system uses an FMA for remote management/broadcast configuration, configure the FMA device
with an FMA Configuration file that only contains a “0 Mapped Channels” FTG Channel Map to broad-
cast to the TV EBL(s). Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the
Installation & Setup manual for the FMA device for further information.
50
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: LD320H/LD325H & LD340H/LD345H Rear Jack Panel
AUDIO IN (RGB/DVI)
Audio connection for
RGB or DVI device.
RJP
Connection for Remote Jack
Pack (RJP) Control cable.
REMOTE CONTROL OUT
IR output for controlling an
auxiliary device.
UPDATE
Restricted to
software updates.
RESET
Initiates a hardware
reset and switches the
TV to standby.
AUDIO/VIDEO IN 1
Connection for composite audio/
video output from external device.
ANTENNA IN
26LD320H, 26LD340H, &
26LD345H only. Connect
to Antenna/CATV.
ANTENNA IN
RS-232C IN
(SERVICE ONLY)
.....
RESET UPDATE
RJP
....
REMOTE
CONTROL
OUT
..........
AV IN 1
RS-232C IN
Use for downloading
software updates, etc.
HDMI
2
1
L/MONO-AUDIO-R
VIDEO
GAME
AUDIO IN
(RGB/DVI)
CONTROL/
MPI
.....
.....
.....
HDMI
/DVI IN
..........
TV-LINK
CFG
RGB IN (PC)
TV-LINK CFG
Use for direct PC-to-TV
FTG configuration.
SPEAKER
(
)
OUT
8
PB
PR
R
L
AUDIO
Y
VIDEO
COMPONENT IN
GAME CONTROL/MPI **
COMPONENT IN
Connection for component
output from external device.
HDMI/DVI IN
Connection for HDMI/DVI
output from external device.
When the TV/EBL is in Pass-through Mode,
the MPI function enables an external MPI
control device (i.e., clone programmer, VOD/
PPV STB, etc.) to control the TV. Game
Control—EBL in LodgeNet PPV Mode only.
RGB IN (PC)
Connection for RGB
output from PC.
SPEAKER OUT (8Ω) *
Connect to 8 ohm self-powered
speaker input. Intended for special
applications, such as a powered bath-
room speaker with volume control.
* This stereo jack provides a mono speaker fixed-level, 1 watt output (audio +, audio -, w/ground shield).
Do NOT plug in a mono connector, as this may damage the TV.
** On 32/37/42LD320H and 32/37LD325H TVs, this is a GAME CONTROL port only. GAME CONTROL
function as described above. On these TVs, the MPI port is located on the same plate as the RF Antenna
jack (see next page).
206-4186
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Side Connections Panel / RF Antenna & MPI Connections
Side Connections Panel
USB IN
Insert USB memory device
for software updates, cloning
purposes, FTG Mode via CPU
configuration, picture/music
A/V 2 Input
entertainment, etc., as applicable.
L/MONO-AUDIO-R IN
Connect to audio output jacks
on external device. For only
mono audio output, connect to
Left audio input.
VIDEO IN
Connect to video output port on
external device (see Reference
section, “TV Camport Auto Sense
Operation,” for further information).
AV IN 2
RF Antenna & MPI Connections
Antenna
or CATV
ANTENNA IN
Connect to Antenna/
CATV.
Notes:
• On 26LD320H, 26LD340H, and 26LD345H
TVs, the RF Antenna jack is on the rear jack
panel (see previous page).
MPI
• On 26LD320H and all LD340H and LD345H
TVs, the MPI port is located on the rear jack
panel (dual-purpose GAME CONTROL/MPI
port).
Enables an external MPI control
device (i.e., clone programmer, VOD/
PPV STB, etc.) to control the TV when
the EBL is in Pass-through Mode.
52
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
General Troubleshooting
Some Quick and Easy Tips for Resolving Problems
Symptom
Possible Cause(s)
Possible Solution(s)
Installation
Cannot direct enter
channel number.
(TV in Pass-through Mode) Installer Menu If Installer Menu item 028 CH. OVERIDE is set to 0, only
item 028 CH. OVERIDE is set to 0, i.e.,
disabled (recommended setting).
channels that are active in the TV’s channel lineup can be
selected. Set CH. OVERIDE to 1 to allow access for direct
keypad entry to all channels.
(TV in FTG Mode) The channel entered is Channel access is restricted to channels included in the FTG
not part of the FTG Channel Map.
Channel Map. If necessary, make changes to the FTG
Channel Map using the FTG Device Configuration Application.
Power
No power.
See troubleshooting flow chart on following page.
Display Panel Picture
No picture.
Display panel is turned off.
• Turn TV ON.
• Power failure?
Antenna/cable not connected.
Connections incorrect.
MPI not connected.
Connect antenna/cable signal to TV
Check connections on TV
If applicable, connect MPI cable to MPI device.
Try another channel.
Encrypted program.
Wrong tuning band.
Adjust Installer Menu settings.
Erratic Operation
Installer Menu setup.
Wrong Installer Menu settings.
Adjust Installer Menu settings as required.
Installer Remote
Remote doesn’t work.
Remote not in TV Mode.
Not aimed at IR remote sensor.
Remote too far from IR sensor.
MPI not connected.
Use MODE key to select “TV”; puts remote into TV Mode.
Point remote at IR receiver on TV.
Move remote closer to IR receiver on TV or darken room.
If applicable, connect MPI cable to MPI device.
Remove obstructions.
IR path to TV’s receiver obstructed.
Weak batteries.
Replace batteries.
Wrong battery polarity.
Check that “+” and “-” match in battery compartment.
Dim room light.
Too much light in room.
Wrong Installer Remote.
Requires compatible Installer Remote. Contact your LG
dealer.
Picture Reception
Normal picture,
poor or no sound.
Audio muted.
Press MUTE or use Volume Up key to increase sound level.
Try a different channel.
Broadcast problem.
Note: For other problems not caused by the TV, refer to the other devices’ operating guide(s).
206-4186
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Cont.)
Troubleshooting Flow Chart
Controller
Quick Check
STATUS
LED on PTC
Board
TV
Plug into AC
Power outlet.
No
No
connected
to AC
Power?
blinking?
Yes
Yes
Bad
TV
Cycle the power by
removing and reconnecting
the AC Power cord. Then,
observe POWER LED
on front of TV.
No
POWER
LED lit?
Bad Digital
Board
TV
No
Bad
TV
responded?
Yes
Yes
Press POWER on
LG Installer Remote.
Press VOLUME UP/
DOWN or MUTE key on
in-room or system
integrator-supplied remote.
TV
No
Bad
TV
turned ON?
Contact system
TV
No
integrator for additional
troubleshooting
assistance.
responded?
Yes
Yes
Press VOLUME UP/
DOWN or MUTE key
on LG Installer Remote.
End
54
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Cont.)
Commercial Mode Check / FTG Operation Troubleshooting
Commercial Mode Check
Use this flowchart to determine whether the TV is currently in Commercial Mode.
Press POWER on
Installer Remote.
TV
connected
to AC
Power?
No
No
Plug into AC
Power outlet.
TV turned
ON?
Yes
Yes
Bad
TV
Leave the TV set ON,
and press MENU on the
Installer Remote.
On-screen
menu display
no longer
Function
Menu
on display?
TV is not in Commercial
Mode. Call Technical
Support for assistance.
Press MENU repeatedly
as if to access the
Installer Menu.
No
No
toggles?
Yes
Yes
TV is in
TV is in
Commercial Mode.
Commercial Mode.
FTG Operation Troubleshooting
The following table provides troubleshooting information for when the EBL is configured in the FTG Mode of operation.
Symptom
Possible Cause(s)
Solution(s)
Communication Error
(“Communications
Timeout”)
Cable(s) not connected.
Check and connect communication cables.
TV not powered.
Check/connect the TV power cord.
TV not turned ON.
TV needs to be turned ON (default FTG Mode).
Wrong COM
(communication) port.
In the FTG Device Configuration Application, select the
correct COM port for the cable being used.
206-4186
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Cont.)
Clone Programmer Troubleshooting
Caution: Do not connect
a clone programmer to a
PPV card installed in the
Reset Clone Programmer After Static Shock
After replacing exhausted batteries (LT2002 only), or if the clone programmer
behaves strangely after a static shock:
Master or Target TVs. Also, if
the TV is in LodgeNet PPV Mode
(check with the site administrator
if you are not certain), do not
connect a clone programmer to
the GAME CONTROL/MPI port.
Either of these actions will
• TLL-1100A: Turn the TLL-1100A OFF and then ON.
• LT2002: Use a paper clip or similar instrument inserted through the small hole
marked RESET to activate the internal reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may be necessary to set the
clone programmer clock from a TV containing the correct time.
Note: Both the Master and Target TVs must be in Pass-through Mode for cloning
purposes. See also IMPORTANT CLONING INFORMATION on page 23.
damage the clone programmer
and, if applicable, the PPV card.
Clone Programmer
Symptom
Possible Cause(s)
Not enough time to copy entire
TV setup.
Possible Solution(s)
Clone copies setup in less
than 30 seconds.
TLL-1100A: Turn the TLL-1100A OFF and then ON.
LT2002: Press RESET on clone programmer.
Then redo Learn/Teach. (Learning usually takes about 90 seconds;
Teaching usually takes 3 to 4 minutes.)
Remote does not operate
clone programmer.
Wrong Installer Remote.
Only use an LG Installer Remote to operate clone programmer
with TV.
Clone menu does not dis-
play on TV screen, TLL-
1100A shows error mes-
sage, or LT2002 LED does
not blink.
MPI cord not connected.
TV not turned ON.
Connect MPI cord properly, and ensure good connection.
TV must be powered ON for clone programmer to work.
Install four (4) fresh AA high-quality alkaline batteries.
Ensure the TLL-1100A is fully charged or connected to AC power.
(LT2002 only) Weak batteries.
(TLL-1100A only) No charge.
Clone menu hard to read.
No time set.
Weak signal.
Connect TV to a reliable analog channel signal source.
Set time on a TV, and copy time to clone programmer.
Time not available.
Clone programmer problem.
Clone not working.
• Try a different clone programmer.
• Reset the clone programmer.
Clone scans channels
more than once.
Clone should only scan channels Ensure TV is set up correctly, and try cloning again.
once.
Master and Target TVs
Symptom
Possible Cause(s)
Possible Solution(s)
Cloning did not work.
Procedure interrupted.
Wait until procedure complete message is displayed.
Different TV models.
Cloning is only possible with identical model TVs.
Step(s) omitted or not performed. Refer to the applicable cloning procedure(s), and make sure all
tasks were performed.
(LT2002 only) Clone time
disappeared.
Batteries were removed.
Batteries must remain installed to retain time settings.
New setup not present.
Target TV not reset.
Disconnect Target TV from AC power for 15 seconds.
• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.
• If the TV does not display a picture (blank screen) after a few seconds, just change channels.
56
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary of Terms
A list of definitions for some of the words found in this guide.
75 OHM RF CABLE
COMPONENT VIDEO
OUTPUT
The wire that comes from an off-air
antenna or cable service provider. The
end looks like a hex-shaped nut with a
wire through the middle. It screws onto
the Antenna/Cable threaded jack on the
back of the TV.
Uses three wires for transporting three-
color video signals. The end result is
usually better video quality.
Refers to the output jack that sends a
signal out of a VCR, DVD, or other A/V
device.
COMPOSITE VIDEO
PHYSICAL CHANNEL NUMBER
The actual channel number. Analog
channels use the Physical Channel
number and digital channels can use a
Virtual Channel number.
Typical video jack, uses one wire for
transporting three-color video signals.
300 TO 75 OHM ADAPTER
DELETE
A small device that connects a 2-wire
300 ohm antenna to a 75 ohm RF jack.
It is usually about an inch long with two
screws on one end and a round opening
with a wire extending out the other end.
Lets you remove channels from the list
that the end user can scroll through
using Channel Up/Down.
RGB (RED, GREEN, BLUE)
Connection input or output port available
for producing a video image using three
separate colors: Red, Green, and Blue.
DIGITAL TELEVISION
High-resolution, cinema-quality television
signals transmitted digitally.
A/V CABLES
RS-232
Audio/Video cables. Three cables
bunched together—right audio (red), left
audio (white), and video (yellow). A/V
cables are used for stereo playback of
videocassettes and for higher quality pic-
ture and sound from other A/V devices.
Serial communication port through
which firmware is downloaded.
DVI
Digital Video Interface. Accommodates
analog and digital interfaces with a
single connector.
2ND AUDIO PROGRAMMING/SAP
Second Audio Programming (SAP) is
another, separate audio channel avail-
able with some programming. Choosing
SAP often refers to listening to audio in
another language, such as Spanish or
French.
HDMI
A/V DEVICE
High-definition multi-media interface.
Any device that produces video or sound
(VCR, DVD, cable box, or television).
HDSTB
High-definition set top box. Refers to a
tuner device that receives high-definition
television signals which have higher res-
olution than ordinary analog TV signals.
AMPLIFIER
SIGNAL
An electronic device that amplifies sound
from a television, CD player, VCR, DVD
player, or other Audio/Video device.
Picture and sound traveling through a
cable, or over the air, to the TV.
HDTV
STEREO SOUND
ANTENNA
High-definition television. Refers to tele-
vision signals that have higher resolu-
tion than ordinary analog TV signals.
Stereo (Stereophonic) sound refers to
audio that’s divided into right and left
sides.
The physical receiver of television signals
sent over the air. A large metal piece of
equipment does not always have to be
visible to be using an antenna.
INPUT
TUNER
Refers to the input jack that receives a
signal from a TV, VCR, DVD Player, or
other Audio/Video device.
Device that picks up the broadcast sig-
nal and turns it into picture and sound.
b-LAN
LodgeNet Interactive Corporation
proprietary RF communication system
used to configure/control TV via RF
distribution system.
VIRTUAL CHANNEL NUMBER
JACK
A re-mapped channel number. Analog
channels use the Physical Channel
number; however digital channels use a
Virtual (or false) Channel number.
An input or output connector on the
back of a TV, VCR, DVD Player, or other
Audio/Video device.
CABLE
Cable service box. Refers to the
descrambler box cable subscribers use
to receive cable programming signals.
MONO SOUND
XDS
Mono (monaural) sound is one channel
of sound. On more than one speaker, all
the speakers play the same audio.
Extended Data Service. Additional
program information included on the
signal provided at the discretion of the
broadcaster.
CATV
Programming provided by a cable
service.
information.
206-4186
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Revision History / Notes
Document Revision History
Date
Description
May 2011
November 2011
Revision A: New document
Revision B: LD320H/LD325H models added to document, also updates for external
MPI control
select TVs, Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads
tab at the bottom of the TV page, and select the required document(s) from the Downloads list.
Notes
58
206-4186
Download from Www.Somanuals.com. All Manuals Search And Download.
For Customer Support/Service, please call:
1-888-865-3026
Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG
Electronics U.S.A., Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other
trademarks or registered trademarks are the property of their respective owners.
206-4186
© Copyright 2011, LG Electronics U.S.A., Inc.
Revision B
Download from Www.Somanuals.com. All Manuals Search And Download.
|