Congratulations, you now own Kustom's KPM7200 Powered Mixer,
a 24-bit digital, portable and powerful 200 Watt PA mixer/amplifier.
The Kustom KPM7200 is easy to operate and easy to understand. Before operating your
KPM7200, please read and understand all setup and safety instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP DIAGRAM A
MIXER FRONT
15
16 17 18
19
20
21
22
23
1
2
3
4
24
5
6
25
26
7
8
9 10 11 12 13 14
SETUP DIAGRAM B
MIXER REAR
27
28
29
30
2
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CONTROLS
FRONT PANEL
1)
2)
3)
4)
5)
6)
Effects Controls: Adjusts the amount of signal that is sent to the digital effects processor.
Monitor Controls: Adjusts the amount of signal that is sent to the Master Monitor control.
Tone Controls: Adjusts the balance of bass and treble from the individual channels.
Main Controls: Adjusts the volume of the individual channel.
Line Input: Input connection for 1/4" line level sources (Keyboards, drum machines, etc.)
Microphone Input: Input connection for balanced Low-Z signals (Microphones, etc.)
7-8) Instrument Inputs: Input connection for instruments (Acoustic Guitars, Electric Guitars, etc.)
9)
Effects Send: Output connector used to send a line level signal from the KPM7200 to an
outboard effect. This connector takes a signal feed from the individual channel's Effects controls.
10)
Aux Return: Input connector used to receive a signal from an outboard effect or signal source. The signal from
this connector is fed to the effect Master (16) control. The Effect Master control (16) will adjust the volume of this signal
source.
11)
12)
Preamp Output: Line level output for the preamp. This control takes a signal feed from the Main Master control.
Power Amp Input: Input connector for the Power Amp. NOTE: When a line level signal source is inserted into
this connector, the signal from the Kustom KPM7200's individual channels are disconnected and will not function. Only
the outboard signal source will be amplified.
13)
14)
Monitor Output: Output connector to send a line level signal to a monitor amplifier or powered monitor.
Footswitch: Standard Tip-Ring-Sleeve wired footswitch to turn digital effects on and mute the channels of the
KPM7200. Tip connection turns the Effects on and off. The Ring connection will mute the individual channels.
15)
16)
Digital Effects Indicators: These LED's show what digital effects have been chose. NOTE: No LED's are lit
when the Effects are muted via footswitch.
Effects Master: Controls the volume of digital effect signal to the Main Master control.
17-18) Effect Select: These two push buttons will scroll through the digital effect options. Pressing the UP button will
advance the digital effect selection to the next selection higher than the present selection. Pressing the DOWN
button will advance the digital effect selection to the next selection lower than the present selection. NOTE: When
scrolling past the top or bottom of the effects selection, the effects selection will automatically go to the opposite end
of the selections.
19)
Equalizer: These controls adjust overall tone of the mixer. Each slide control adjusts the amount of specific
frequencies + or
– 12dB.
20)
Main Master: Controls the total volume on the individual channels. NOTE: The playback volume is not affected
by the Main Master control.
21)
22)
Power On Indicator: Power is on when LED is lit.
Monitor Master: Controls the total volume of the individual channel's monitor sends.
NOTE: The Monitor output is still active when Main channels are muted via footswitch.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
23)
24)
Channels On Indicator: Channels are active when LED is lit.
Playback Volume: Controls the volume from the Playback RCA input jacks (25).
NOTE: The Playback feature is not affected by the Main Master control and will remain
active even when the mute function is active via the footswitch.
25)
26)
Playback RCA Jacks: Input connector CD, Tape or any line level stereo signal source.
Allows you to play recorded music through the mixer.
Record RCA Jacks: Output connectors to send line level signal to a record device such as a tape recorder or
computer.
REAR PANEL
27)
AC Cord Connector: Insert the AC cord (supplied) firmly into the AC connector.NOTE: Replace the AC power
cord if protective jacket is damaged or round ground pin is damaged or removed.
28)
Power Switch: The KPM7200 is turned ON when the switch is in the UP position.
Press the switch to the DOWN position when not in use.
29-30) Speaker: Connectors for 8 Ohm speaker cabinets each.
NOTES: #1 do not connect more than two 8 Ohm speaker cabinets to the output of the KPM7200 mixer/amplifier.
Total load must not go below 4 Ohms.
#2. It is not necessary to use both A & B output jacks.
The KPM7200 will operate at 8-16 Ohms.
QUICK-START SETUP INSTRUCTIONS
Making Connections:
•
•
•
Connect 1/4" non-shielded speaker cables to the speaker out jacks on the rear of the KPM7200 (29 & 30),
then connect the opposite end of each speaker cable to the speaker enclosures.
Connect instruments and microphones into the appropriate input connectors located on the front of the mixer.
Low Impedance Microphones (6), Line Level (5), High Impedance Instruments (7 &8), tape/CD (25).
Make sure the power switch is turned to the off position and attach the AC power cable into the fused AC
input (27) located on the rear of the mixer.
Master Section:
•
Turn the Main Master control (20), and Playback Master (24) counter clockwise.
•
Adjust the master equalizer slide controls (19) to the center 0dB position.
Input Section:
•
Turn all channel volume controls (4) counter clockwise.
•
Turn all tone controls (3) to the 12 O'clock position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING
•
•
•
•
Press the Power switch (28) to the ON position.
Turn the Main Master control (20) to the 12 O'clock position.
Turn the Main control (4) clockwise on each channel to achieve the desired volume. (One channel at a time)
After you are satisfied with the basic mix of the individual channels, use the Main Master control (20) to adjust
the overall volume of the mixer.
•
•
Use the Graphic Equalizer slide controls (19) to control feedback and contour the audio to the overall desired
sound.
Select a digital effect (if desired). The KPM7200 offers a choice of eight 24-bit
digital effects.
STAGE EFFECTS
Large Room
Small Room
Small Hall
STUDIO EFFECTS
Chorus
Chorus / Reverb
Slap-back Echo
Delay
Large Hall
•
Adjust the effects controls on the individual channels (1) to desired volume.
Adjust the effects Master control to achieve the total desired amount of effects
in the mix.
•
Reset the Main master control (20) to desired volume.
That's it. Enjoy...
Servicing: The AC Fuse is accessible underneath the AC cable connector. No user serviceable parts inside. Please contact
your nearest Authorized Kustom Service Center or Kustom Inc. directly for service.
Kustom Inc. Customer Service can be reached at (513) 451-5000 ext. 504, [email protected] or locate an Authorized
Service Center from the World Wide Web at www.kustom.com.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KPM7200
Specifications
Model
KPM7200
KPM7200 Powered Mixer
Output Power
200W
4 ohms @ 5% THD
160W
4 ohms @ 0.4% THD
Frequency Response
Total Harmonic Distortion
Hum & Noise
20Hz-20kHz
Actual response is tailored to speaker cabinet for
accurate acoustical response.
less than 0.4%
Measured at 1VRMS (0dBv) at record output,
effects send, or insert output
-115dB
-60dB
-50dB
Mic Input, Rs=150 ohm, 20-20kHz
Residual Noise, all level controls 0% (minimum)
Nominal System Noise, all level controls at 50%
System Gain
All measurements made at 1kHz
77dB
60dB
70dB
36dB
50dB
44dB
50dB
50dB
80dB
Mic to Power Amp Out (Ch 1 - Ch 5)
Line to Power Amp Out (Ch 1 - Ch 7)
Instrument to Power Amp (Ch 6 - Ch 7)
Playback to Power Amp
Mic to Record Output
Mic to Effects Send
Mic to Preamp Output
Mic to Monitor Output
Crosstalk
Input Channel Equalization
Master Equalization
Digital Effects
Channel to channel, 1kHz
Special curve that adjusts bass, mid, and treble frequencies
100 to 10Khz, 7 Band, 1 Octave Graphic, all ±12dB
24 bit DSP, 8 effects; small room, large room, small hall, large hall,
chorus, chorus reverb, slap back (delay), echo
Phantom Power
Footswitch
+15V
Applied to all Mic Inputs thru 3.3K resistors
Digital effects ON/OFF and Channel ON/OFF (playback remains active)
Power Requirements
USA/Canada
Europe
120VAC/60Hz, 160W nominal
230VAC/50Hz, 160W nominal
UK
230VAC/50Hz, 160W nominal
Australia
Japan
240VAC/50Hz, 160W nominal
100VAC/50-60Hz, 160W nominal
210 (Height) x 480 (Width) x 270 (Depth), 11 kg
8 1/4 (Height) x 19 (Width) x 10 5/8 (Depth), 24 lbs
Dimensions
mm/kg
inches/pounds
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EC Declaration of Conformity
We:
Kustom Musical Amplification Inc.
4940 Delhi Pike
Cincinnati, OH 45238
Tel: 1-513-451-5000 Fax: 1-513-347-2298
Declare that the product
Product name:
Kustom
Product model number:
KPM7200, Contains one KPM7200
to which this declaration relates is in conformity with the following standards;
EN55013 (A12) : 1995
Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and
associated equipment.
EN55020: 1995
Electromagnetic immunity of broadcast receivers and associated equipment.
Limits for harmonic current emissions (equipment input current < 16A per phase).
EN61000-3-2: 1995
EN61000-3-3: 1995
Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated
currents < 16A.
EN55103-1: 1995
EN60065: 1994
Electromagnetic Compatibility - Product family standard for Audio, Video Audio-visual and
entertainment Lighting Control Apparatus.
Safety requirements for main operated electronic and related apparatus for household and similar
general use.
Following the provisions of EU Council Directive(s): 72/73 EEC and 89/336/EEC.
We the undersigned, hereby declare that the equipment specified above conforms to the aforementioned directive(s).
Name of authorized person: Rick Kukulies, VP Engineering
Signature:
Date: 05 June 2001
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Kustom Inc., 4940 Delhi Pike, Cincinnati, OH • USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|