Kustom Stereo Amplifier HV 30 User Manual

OWNERS MANUAL  
MODEL HV30  
Congratulations on the purchase of your new Kustom® High Voltage HV™ Series guitar amplifier.  
This model utilizes an exclusive preamp design that combines a 12AX7 tube, known for its robust tonal  
qualities, with solid-state circuitry that provides consistency of performance and reliability. The result is  
rich, dynamic tone that is perfect for a wide variety of playing styles and environments. Inside this  
manual you'll find details about your HV Series model. Everyone at Kustom wishes you many years of  
enjoyment with your new amplifier!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
ENGLISH  
Danger  
Exposure to extremely high noise levels may cause a  
permanent hearing loss. Individuals vary considerably to  
noise induced hearing loss but nearly everyone will lose  
some hearing if exposed to sufficiently intense noise for a  
sufficient time.  
1. Read all safety and operating instructions before using this  
product.  
2. All safety and operating instructions should be kept for  
future reference.  
3. Read and understand all warnings listed on the operating  
instructions.  
4 . Follow all operating instructions to operate this product.  
5. This product should not be used near water, i.e. Bathtub,  
sink,swimming pool, wet basement, etc.  
The U.S. Government's Occupational Safety and Health  
Administration (OSHA) has specified the following  
permissible noise level exposures:  
6. Only use dry cloth to clean this product.  
7. Do not block any ventilation openings, It should not be  
placed flat against a wall or placed in a built-in enclosure  
that will impede the flow of cooling air.  
DURATION PER DAY (HOURS)  
SOUND LEVEL (dB)  
8
6
4
3
2
1
8. Do not install this product near any heat sources ;such  
as,radiators, heat registers, stove or other apparatus  
(including heat producing amplifiers) that produce heat.  
90 93 95 97 100 103  
According to OSHA, any exposure in the above permissible  
limits could result in some hearing loss. Ear plugs or  
protectors in the ear canal or over the ears must be worn  
when operating this amplification system in order to prevent  
a permanent hearing loss. If exposure in excess of the limits  
as put forth above, to insure against potentially harmful  
exposure to high sound pressure levels, it is recommended  
that all persons exposed to equipment capable of inducing  
high sound pressure levels, such as this amplification  
system, be protected by hearing protectors while this unit is  
in operation.  
9. Do not defeat the safety purpose of the polarized or  
grounding-type plug. A polarized plug has two blades with  
one wider than the 0ther.A grounding-type plug has two  
blades and a third grounding prong. The wide blade or the  
third prong are provided for your safety If the provided plug  
does not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
10. Protect the power cord being walked on or pinched,  
particularly at Plugs, convenience receptacles and the point  
where they exit from the apparatus. Do not break the ground  
pin of the power supply cord.  
11 . Only use attachments specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket,  
or table specified by the manufacturer or  
sold with the apparatus. When a cart is  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
used, use caution when moving cart/  
apparatus combination to avoid injury  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO  
NOT REMOVE CHASSIS. NO USER-SERVICEABLE  
PARTS INSIDE. REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
S3125A  
from tip-over.  
13. Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.  
14. Care should be taken so that objects do not fall and liquids  
are not spilled into the unit through the ventilation ports or  
any other openings.  
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE  
OF NON-INSULATED "DANGEROUS VOLTAGE" WITHIN THE  
PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE  
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.  
15. Refer all servicing to qualified service personnel. Servicing  
is required when the apparatus has been damaged in any  
way; such as, power-supply cord or plug is damaged, liquid  
has been spilled or objects have fallen into the apparatus,  
the apparatus has been exposed to rain or moisture, does  
not operate normally or has been dropped.  
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE  
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)  
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.  
16. WARNING: To reduce the risk of fire or electric shock, do not  
expose this apparatus to rain or moisture.  
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING  
AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,  
SHALL BE PLACED ON THE APPARATUS.  
17. The MAINS plug or an appliance coupler is used as the  
disconnect device, the disconnect device shall remain  
readily operable.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANTES INSTRUCTIONS DE SECURITE  
FRENCH  
Danger  
1. Lire avec attention toutes les recommandations et précautions  
d'emploi avant d'utiliser ce produit.  
L‘exposition a des niveaux eleves de bruit peut provoquer  
une perte permanente de l’audition, Chaque organisme  
humain reagit differemment quant a la perte de l’audition,  
mais quasiment tout le monde subit une diminution de  
I’acuite auditive lors d’une exposition suffisamment  
longue au bruit intense. Les autorites competentes en  
reglementation de bruit ont defini les expositions tolerees  
aux niveaux de bruits:  
2. Toutes les recommandations et précautions d'emploi doivent  
être conservées afin de pouvoir s'y reporter si nécessaire.  
3. Lire et comprendre tous les avertissements énumérés dans les  
précautions d'emploi.  
4. Suivre toutes les précautions d'emploi pour utiliser ce produit.  
5. Ce produit ne doit pas être utilisé près d'eau, comme par  
exemple baignoires, éviers, piscine, sous-sol humides ... Etc.  
6. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.  
7. Ne bloquér aucune ouverture de ventilation. Ne pas placer le  
produit tout contre un mur ou dans une enceinte fernée, cela  
gênerait le flux d'air nécessaire au refroidissement.  
DURE EN HEURES PAR JOUR  
8
6
4
3
2
1
8. Ne pas placer le produit près de toute source de chaeur telle  
que radiateurs, arrivées d'air chaud, fourneaux ou autres  
appareils générant de la chaleur (incluant les amplificateurs  
producteurs de chaleur) .  
INIVEAU SONORE CONTINU EN dB  
90 93 95 97 100 103  
Selon les autorites, toute exposition dans les limites  
citees ci-dessus,peuvent provoquer certaines pertes  
d’audition. Des bouchons ou protections dans l’appareil  
auditif ou sur l’oreille doivent etre portes lors de  
l’utilisation de ce systeme d’amplification afin de prevenir  
le risque de perte permanente de l’audition, Dans le cas  
d’expositions superieures aux limites precitees il est  
recommande, afin de se premunir contre les expositions  
aux pressions acoustiques eIevees potentielIement  
dangeureuses, aux personnes exposees aux  
9. Ne pas négliger la sécurité que procure un branchement  
polarisé ou avec raccordement à la terre, Un branchement  
polarisé comprend deux fiches dont l'une est plus large que  
l'autre. Un branchement à la terre comprend deux fiches plus  
une troisième reliée à la terre. Si la fiche secteur fournie ne  
s'insert pas dans votre prise de courant. consulter un  
'électricien afin de remplacer votre prise obsolète.  
10. Protéger le cordon d'alimentation de tout écrasement ou  
pincement, particulièrement au niveau des fiches, des  
réceptacles utilisés et à l'endroit de sortie de l'appareil. Ne pas  
casser la fiche de terre du cordon d'alimentation.  
11. Utiliser uniquement les accessoires spécifiés par le  
constructeur.  
equipements capables de delivrer de telles puissances,  
tels ce systeme d’amplification en fonctionnement, de  
proteger l’appareil auditif.  
12. Utiliser uniquement avec le chariot de  
transport, le support, le trépied, la  
console ou la table spécifiés par le  
constructeur ou vendus avec l'appareil.  
Lors de l'utilisation d'un chariot, bouger  
ATTENTION  
RISQUE DE CHOC ELECTRIQUE  
NE PAS OUVRIR.  
S3125A  
avec précaution l'ensemble chariotlappareil  
afin d'éviter les dommages d'un renversement.  
ATTENTION: AFIN DE LlMlTER LE RISQUE DE CHOC ELECTRIQUE,  
NE PAS ENLEVER LE CHASSIS. NE CONTIENT PAS DE  
PIECES POUVANT ETRE REPAREE PAR L’UTILISATEUR.  
CONFIER LE SERVICE APRES-VENTE AUX  
13. Débrancher cet appareil lors d'orages ou s'il n'est pas utilisé  
pendant une longue période.  
REPARATEURS AGREES.  
14. Des précautions doivent être prises afin qu'aucun objet ne  
tombe et qu'aucun liquide ne se répande à l'intérieur de  
l'appareil par les orifics de ventilation ou n'importe quelle autre  
ouverture.  
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE  
DE VOLTAGE DANGEREUX NON-ISOLE A L'INTERIEUR DE CE PRODUIT  
QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT IMPORTANTE POUR  
PROVOQUER UN CHOC ELECTRIQUE AUX PERSONNES.  
15. Pour toutes interventions techniques s'adresser à un  
technicien qualifié.L'intervention technique est nécessaire  
lorsque l'appareil a été endommagé de n'importe quelle façon,  
comme par exemple si le cordon secteur ou sa fiche sont  
détériorés,si du liquide a coulé ou si des objets sont tombés à  
l'intérieur de l'apparei1,si l'appareil a été exposé à la pluie ou à  
l'humidité, s'il ne fonctionne pas normalement ou s'il est tombé.  
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE  
D'INSTRUCTIONS D'UTILISATION ET DE MAINTENANCE DANS LES  
DOCUMENTS FOURNIS AVEC CE PRODUIT.  
16. ATTENTI0N:Pour réduire le risque d'incendie ou de choc  
electrique ne pas exposer l'appareil à la pluie ou à l'humidité.  
AFIN DE REDUIRE LES RISQUÉ D'INCENDIE ET DE DECHARGE  
ELECTRIQUE, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A  
L'HUMIDITE.  
17. La prise Mains, au coupler, est utilisé pour la source  
d'alimentation êlectrique. Il est conseillê de garder cette prise  
facilement accessible.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
HV30 CONTROL PANEL FUNCTIONS  
6
2
4
7
9
15  
17  
1
3
5
8
10  
11  
12  
13  
14  
16  
18  
19  
1.) Guitar Input Jack - this is a 1/4" 2-conductor input jack for plugging in your instrument. It is  
intended for guitars but will accept other instruments as well.  
2.) Lead Channel On LED - when this LED light is on, it indicates that the Lead Channel is active.  
3.) Gain - adjust this clockwise to increase the amount of distortion. At lower ranges of the control, you  
get a less distorted sound. As you increase the gain, you add tremendous amounts of distortion to  
the signal for a harder edged "crunch" tone.  
4.) Grind/Crunch Switch - this switch selects either the CRUNCH or GRIND preamps. Each preamp  
offers a different tonal variation.  
5.) Volume - this is a volume control for the Lead Channel ONLY.  
6.) Channel Select Switch - this switch selects between the Lead or Rhythm Channel.  
7.) Rhythm Channel On LED - when this LED light is on, it indicates that the Rhythm Channel is  
active.  
8.) Gain - adjust this clockwise to increase the amount of gain of the Rhythm Channel. The gain is  
applied before the tone controls.  
9.) Fat/Lean - Selecting Fat allows the 12AX7 tube input stage to be over-driven, giving a fatter sound.  
10.) Volume - this is a volume control for the Rhythm Channel only.  
11.) Bass - this control is the bass control for both channels. It is passive and set to shelve frequencies  
at 100Hz. Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise, the low will  
be rolled off -12db.  
12.) Middle - this control is the midrange control for both channels. It is passive and set to shelve  
frequencies at 1KHz. Turning it fully clockwise, the signal is unaltered. Turning it counterclockwise,  
the low will be rolled off - 12db.  
13.) Treble - this is the high frequency tone control for both channels. It is passive and set to shelve  
frequencies at 3KHz on the instrument channel. Turning it fully clockwise, the signal is unaltered.  
Turning it counterclockwise, the highs will be rolled off - 12db.  
14.) Effects Level - this control adds the digital effects section and mixes it into the main signal. Sixteen  
different effects are available.  
15.) Toggle Tap - This momentary switch performs different functions, depending on which effect is  
selected. Page 6 describes each effect in detail and how to enhance its usefulness with this switch.  
16.) Program Select - this switch will select any of sixteen different effects. Page 6 describes each effect  
in detail.  
17.) Effects Active - this switch engages the digital effects section. The Footswitch over-rides this switch  
when it's plugged into the amp.  
18.) Jewel Light - this jewel light lets you know that the amplifier is on.  
19.) Power Switch - this switch turns on and off the AC power to the amp.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
HV30 Effects  
Effects Level This control adds the digital effects section and mixes it into the main signal. Sixteen  
different effects are available.  
Program Select This switch will select any of the sixteen different effects.  
Effects Active This switch engages the digital effects section. The footswitch over-rides this switch  
when it's plugged into the amp.  
Toggle Tap This switch is a dual function depending on which effects program is selected. On “toggle”  
effects, this button pages through alternate variations of the effect. For example, for the Spring Reverb,  
it pages through 3 different degrees of brightness. On “tap” effects, this button selects the rate time at  
which the effect cycles, by tapping the switch twice. For example, for the Delay setting, it selects the  
amount of time between delay repeats (If the 2nd tap is beyond the maximum setting, the time will  
default to the longest available choice).  
Effect Program  
Spring Reverb  
Slap Back  
Chorus  
Description  
Toggle Tap  
Toggle Tap Function  
pages through 3 different degrees of reverb brightness  
toggles between Slapback and Slapback/Reverb  
adjusts chorus rate time  
simulates the spring reverb pan found in vintage tube amps  
a fast 80ms delay for getting those Rockabilly tones  
a beautiful thick chorus that can swish with the best of them  
an organic sounding delay that has that analog warmth  
a sweet and swooshy '70s sounding phaser  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Delay  
adjusts delay time….maximum delay = 680 mS  
adjusts phaser rate time  
Phaser  
Tremolo  
a classic sounding tremolo with a hint of vibrato  
adjusts tremolo rate time  
Trem/Reverb  
Delay/Reverb  
Room Reverb  
Hall Reverb  
Flanger  
a combination effect of tremolo and room reverb  
a combination effect of the delay and room reverb  
the reverb sound of your amp being played in a room  
the reverb sound of your amp being played in a large hall  
a deep flanger for getting those spacey sweeping tones  
gives you that twirling sound of those fancy old organ cabinets  
shifts the pitch up or down one octave from the original signal  
a wah wah that automatically sweeps at your chosen speed  
a combination effect of Rotary with room reverb  
adjusts tremolo rate time  
adjusts delay time…..maximum delay = 350 mS  
adjusts reverb decay time  
adjusts reverb decay time  
adjusts flanger rate time  
Rotary  
ramps between fast and slow rotary speeds  
toggles between octave up and octave down  
adjusts auto wah rate time  
Octave  
Auto Wah  
Roto/Reverb  
Chorus/Reverb  
ramps between fast and slow rotary speeds  
adjusts chorus rate time  
a combination effect of chorus and room reverb  
Effects Module Memory Aside from all the versatility of the built-in effects, the effects module in your  
Kustom amplifier has the ability to store your favorite sounds. All the most recent changes to the Toggle  
Tap button are saved in each of the 16 effect locations. For example, If you tap in your favorite delay  
time, then go to chorus, and then go back to delay, your own tapped delay time will still be saved.  
These setting changes are also retained when powering down the amplifier.  
To Restore Factory Settings If you ever want to restore the effects to the factory default settings, you  
can do this by selecting Program 1 (Delay/Reverb), then holding the tap switch down and  
simultaneously selecting Program 2 (Trem/Reverb).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
HV30 Back Panel  
1
2
3
4
5
Jacks located on chassis bottom in sequence shown above  
1.) External Speaker - this is a 2-conductor 1/4" speaker output jack. Rating is 8 ohms minimum.  
The signal path to the internal speakers is disconnected when using this jack. Make absolute  
sure that a 2-conductors speaker cord is used and it is plugged in to the external speaker  
cabinet before plugging into this jack. Failure to do so could result in electrical shock or damage  
to the amplifier. It is also highly recommended to turn off the AC mains power to the amplifier  
before plugging or unplugging any speakers to this jack.  
2.) Direct (SPKR Emulated) - this is a 3-conductor. XLR output jack for plugging into Lo-Z  
microphone inputs as found on PA or recording mixers. It is intended in place of external mics or  
used as a built-in direct box. Great effort was made in emulating the actual speaker sound.  
3.) Headphone Jack - this is a 3-conductor stereo jack. The amplifier’s internal speaker is  
disconnected when this jack is used.  
4.) CD/Tape Input - this is a 3-conductor 1/4” jack that allows playback from a Compact Disc or  
Tape player. The volume is controlled by the device plugged into this jack.  
5.) Main FT Switch - this 1/4" stereo jack connects a foot-switch to the amplifier. The tip selects the  
rhythm or lead channel. The ring selects the effects active/off. This foot-switch is not included  
with the amplifier. Kustom model KAC-FS201 is recommended to enjoy all the features.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
HV30 AC Mains  
1
2
1.) AC Power Cord Receptacle - AC power cord can be removed for easy storage and  
replacement if damaged. Insert the AC cord (provided) firmly into the AC receptacle. NOTE:  
Replace the AC power cord if protective jacket is damaged or ground pin is damaged or  
removed.  
2.) Fuse - The fuse is located in a fuse tray just below the receptacle. Replace only with same type  
and size. For your convenience, a spare fuse is located inside the fuse tray toward the front. To  
replace fuse, remove AC power cord. Remove fuse tray by pulling the tab located above the  
fuse symbol away from the receptacle.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
HV™ 30  
Specifications  
Tubes  
Output Power  
Preamp  
1-12AX7  
8 Ohms @ 5% THD  
Celestion G12P80  
100 K ohms  
Residual Noise, all level controls 0% (minimum)  
Rhythm Channel, with Volume half and Master Maximum, Boost on 10  
30 Watts, RMS  
1 X 12 Inch  
Single Input  
-60 dBV  
Speakers  
Input Impedance  
Hum & Noise  
Nominal Signal to Noise  
-70 dBV  
System Gain  
30 dBV  
60 dBV  
30 dBV  
60 dBV  
6 dBV  
Rhythm Channel Nominal gain, Volume @ 5  
Rhythm Channel Maximum gain, Volume @ 10  
Lead Channel Nominal gain, Volume @ 5  
Lead Channel Maximum gain, Volume @ 10  
Gain increase at 1 kHz when Crunch/Grind is pressed  
Gain increase at 1 kHz when Fat/Lean is pressed  
All measurements taken with 1 KHz  
input signal, Tone controls flat,  
Effects off. Measured at speaker with  
8 ohm load.  
6 dBV  
XLR Direct Output  
Digital Effects  
After power amp with speaker emulation  
24 bit DSP module, 16 effects w/programmable tap-toggle switch.  
Footswitch Jack  
Tip Selects Rhythm/Lead, Ring selects Effects On/Off  
KAC-FS201 (not included).  
Recommended footswitch  
USA/Canada  
Europe  
UK  
120VAC/60Hz, 60W nominal  
230VAC/50Hz, 60W nominal  
230VAC/50Hz, 60W nominal  
240VAC/50Hz, 60W nominal  
100VAC/50-60Hz, 60W nominal  
Power Requirements  
Dimensions/Weight  
Australia  
Japan  
mm/kg  
425 (Height) x 459 (Width) x 246 (Depth), 15.4 kg  
16 3/4 (Height) x 18 (Width) x 9 5/8 (Depth), 34 lbs  
Inches/Pounds  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EC Declaration of Conformity  
We:  
Kustom Musical Amplification Inc.  
4940 Delhi Pike  
Cincinnati, OH 45238  
Tel: 1-513-451-5000 Fax: 1-513-347-2192  
Declare that the product  
Product name:  
Kustom  
HV™30  
Product model number:  
to which this declaration relates is in conformity with the following standards;  
EN55013 (A12) : 1995  
Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and  
associated equipment.  
EN55020: 1995  
Electromagnetic immunity of broadcast receivers and associated equipment.  
Limits for harmonic current emissions (equipment input current < 16A per phase).  
EN61000-3-2: 1995  
EN61000-3-3: 1995  
Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with  
rated currents < 16A.  
EN55103-1: 1995  
EN60065: 1994  
Electromagnetic Compatibility - Product family standard for Audio, Video Audio-visual and  
entertainment Lighting Control Apparatus.  
Safety requirements for main operated electronic and related apparatus for household and similar  
general use.  
Following the provisions of EU Council Directive(s): 72/73 EEC and 89/336/EEC.  
We the undersigned, hereby declare that the equipment specified above conforms to the aforementioned directive(s).  
Name of authorized person: James Brown, Chief Engineer  
Signature:______________________  
Date: 24 February 2006  
Kustom Amplification Inc.  
4940 Delhi Pike  
Cincinnati, OH 45238  
Tel: 1-513-451-5000 Fax: 1-513-347-2192  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
® Kustom Amplification Inc., 4940 Delhi Pike, Cincinnati, OH • USA  
(800) 999-5558 Web: www.kustom.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Computer Monitor 131081 User Manual
Lincoln Electric Welding System IM702 A User Manual
Lopi Saw 99500146 User Manual
Lux Products Thermostat P722U User Manual
Makita Trimmer 3705 User Manual
Maytag Clothes Dryer MDG17MN User Manual
Maytag Clothes Dryer MEDZ400TQ2 User Manual
Maytag Washer MAF 1060 User Manual
McIntosh Stereo Amplifier MC205 User Manual
Metabo Grinder 600166420 User Manual