KTI Networks Network Card KG 500F User Manual

Installation Guide  
1000Base-X Gigabit Ethernet  
PCI Adapter with SFP Support  
KG-500F series  
DOC.070607-KG-500F-K  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CISPR 22 Class B  
This device complies with EMC directive of the European Commu-  
nity and meets or exceeds the following technical standard: EN55022  
- Limits and Methods of Measurement of Radio Interference Char-  
acteristics of Information Technology Equipment. This device com-  
plies with CISPR 22 Class B.  
CE NOTICE  
Marking by the symbol  
indicates compliance of this equip-  
ment to the EMC directive of the European Community. Such marking  
is indicative that this equipment meets or exceeds the following  
technical standards:  
EN55022/CISPR 22 ClassB  
EN55024 - EN61000-3-2, EN61000-3-3, EN61000-4 series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
The 1000BASE-X Gigabit Ethernet PCI Adapter is a 32-bit LAN  
adapter for use in personal computers with PCI computer bus slots.  
This adapter features a mini-GBIC fiber connector (SFP) for a 1000  
Mbps IEEE 802.3z Ethernet network connection over optical fiber  
cable. The series provides different fiber transceiver types support-  
ing short, middle, and long reach applications.  
Adapter Features  
Supports 32-bit 33/66MHz PCI of Rev.2.1/2.2/2.3 specifica-  
tion  
IEEE 802.3z 1000Base-SX/LX compliant  
Provides Tx 8K / Rx 64KB RAM buffer  
Supports full duplex operation up to 2000Mbps data rate over  
fiber  
Supports full duplex flow control  
Plug-and-Play installation  
Provides LED indicators for easy diagnostic  
Provides SFP to support variety of fiber transceivers  
Complete driver support for most operating systems  
Supports 802.1Q VLAN tagging  
Supports drivers for Windows XP/2K/2K3/VistaX32/  
VistaX64/Linux/NetWare systems and plug-and-play installa-  
tion for Widnows 2K3.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Standards  
IEEE 802.3z 1000Base-SX/LX  
Network Port  
Host Interface  
LEDs  
SFP for 1000Mbps mini-GBIC fiber transceiver  
32-bit 33/66Mhz PCI Rev.2.1/2.2/2.3  
SFP status, Link status, Optical status  
Network Cables 50/125 multimode fiber up to 500m  
62.5/125 multimode fiber up to 220m  
9/125 single mode fiber  
Transfer Rate  
Gigabit Ethernet: 2000Mbps (Full-duplex)  
Driver Support Windows XP, 2000, 2003, VistaX32/64,  
Linux,Netware server  
Power  
Dimension  
Environment  
Consumption PCI 3.3V/400mA max.  
130 x 65 mm  
Operation Temperature: 0oC ~50oC  
Storage Temperature: -20oC ~85oC  
Relative Humidity 5%~95%non-condensing  
Laser Eye Safe  
Approval  
IEC 60825-1 Class 1/CDRH Class I  
FCC Class B,CE CISPR22 Class B  
Model Definitions  
Model  
PCI  
Connector Fiber Cable Support  
500-SX  
Standard  
LC  
62.5/125 MMF up to 200m  
50/125 MMF up to 500m  
MMF up to 550m  
500-LX  
Standard  
LC  
SMF up to 10km  
500/LP-SX  
500/LP-LX  
Low-profile LC  
Low-profile LC  
62.5/125 MMF up to 200m  
50/125 MMF up to 500m  
MMF up to 550m  
SMF up to 10km  
* Standard PCI: mounted with PCI standard bracket  
Low-profile: mounted with PCI low-profile bracket  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Board Components  
The figures show the major components on the adapters with PCI  
standard bracket and PCI low-profile bracket.  
Adapter with PCI standard bracket  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adapter with PCI low-profile bracket  
No. Components  
Description  
1
LINK LED  
This LED lights when the  
fiber connection is established.  
2
SFPLED  
This LED lights when a mini-GBIC  
transceiver module is installed in  
the SFP slot.  
3
4
OL LED  
This LED lights when optical signal  
is presented in the transceiver.  
SFP Slot  
This slot supports mounting a  
mini-GBIC fiber transceiver.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Adapter  
Before installing the adapter, you need the following:  
• A computer system that is compliant with the PCI specifica-  
tions version 2.1 or later.  
• An available PCI bus master slot in the computer  
• The adapter driver diskettes (or CD supplied with the adapter)  
• Fiber cables  
Inserting the Adapter into the PCI Slot  
To install the adapter in your computer, follow these steps:  
1. Turn off the power to the computer.  
2. Remove the computer's cover.  
3. Unscrew and remove the slot cover from the PCI bus slot.  
4. Insert the adapter into the slot and secure the screw.  
5. Replace the computer cover and reconnect all previously  
connected cables.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing Mini-GBIC Transceiver  
A typical mini-GBIC SFP transceiver is shown as follows:  
To install a fiber transceiver into the SFP slot, the steps are:  
1. Insert the fiber transceiver into the mini-GBIC SFP port.  
Normally, a bail is provided for every SFP transceiver. Hold the  
bail and make insertion.  
2. Until the fiber transceiver is seated securely in the slot, place  
the bail in lock position.  
The mini-GBIC SFP slot supports hot-plug installation even when  
the computer is powered and operating.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to the Network  
The rear bracket of the PCI adapter contains two fiber connectors.  
The TX connector is used for transmission and the RX is used for  
reception. When connecting to a device using fiber cable, make sure  
the TX connector of the adapter is connected to the RX connector  
of the device and RX connector is connected to the TX connector of  
the device.  
In order to have a reliable communication between two ends, the  
speed and duplex configuration of the adapter's fiber port and the  
device at the remote end must be same. Configure the driver of the  
adapter as follows: Auto, 1000Mbps, Full-duplex.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Network Driver Installation  
After making the connection to the network, you must install the  
adapter network driver in order to connect the network adapter to  
your network operating system.  
The adapter driver media contain the latest versions of the network  
drivers available when the adapter is shipped from the factory. A  
file, \README.TXT, located in the diskette's root directory con-  
tains a list of the supported driver software and the directory struc-  
tures for the supported operating environments. Please refer to this  
file first before installing any network driver for the adapter.  
Installation for Windows Systems  
For adapter installation on Windows 2003 (Win2K3), the system  
will detect and configure the drivers for the adapter automatically  
with no need for extra driver setup. The adapter is detected as :  
Win2k3  
Realtek RTL8169/8110 Family Gigabit Ethernet NIC  
Using the Associated Drivers in the driver diskette  
After driver setup, the adapter is identified as :  
Realtek RTL8169/8110 Family Gigabit Ethernet NIC  
Link Speed/Duplex Mode options : Auto-negotiation  
Installation for other Systems  
Refer to \README.TXT first in the driver CD for the driver instal-  
lation on other operating systems. The file contains driver informa-  
tion for most of the popular operating systems.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LED Indicators  
The adapter has three LEDs. The interpretations of the LEDs are:  
LINK LED indicates an active 1000Mbps connection is established.  
On : Good link between the adapter and a remote device  
Off : No connection between adapter and a remote device  
Blink: Link on and traffic activities  
SFP LED indicates installation status of mini-GBIC transceiver  
On : A mini-GBIC SFP transceiver is installed in the SFP slot.  
Off : No transceiver is installed.  
OL LED indicates optical signal status  
On : Optical signal is detected.  
Off : No optical signal is detected.  
If you experience any problems, first make sure that the appropri-  
ate driver is loaded, the proper cable is connected to the connector,  
and the connected device complies with 1000BASE-X standard.  
Then recheck the LED.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lenmar Enterprises Battery Charger R2G User Manual
LifeWise Heart Rate Monitor 63 609 User Manual
Link electronic Network Router 860 XL858V User Manual
Lowrance electronic GPS Receiver X 25 User Manual
Makita Grill Accessory 1050D User Manual
M Audio Microphone BC30 RY30562 RY30963 User Manual
Melissa Food Warmer 750 026 User Manual
Metra Electronics Automobile Accessories 99 7326 User Manual
Microsoft MP3 Player HDP 3202 BS User Manual
Microtek Camcorder 8538A001 User Manual