Quick Start Guide
The ZEQ25GT™ Balanced GoTo Equatorial Mount
#7100, #7101
PACKAGE CONTENTS1
•
•
•
•
•
•
•
•
Telescope Mount (with built-in GPS)
Go2Nova® #8408 Hand Controller
1.5-inch Tripod
One 10.4 lbs (4.7 kg) counterweight
Installed AccuAlignTM dark field illuminated polar scope (model #7100 only)
Polar scope LED cable (model #7100 only)
AC adapter (100V-240V)
Controller Cable X 2
•
•
•
•
Manuals (you will need to refer to the full manual for details on set-up and operation).
Tips for set up
Hand controller and mount firmware upgrades (check online for latest version)
Reviews and feedback from other customers
1 The contents may change from batch to batch without notice
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Install Counterweight (CW) Shaft: (1) Remove CW
Shaft Locking Screw from the CW Mounting Nose. (2)
Insert CW shaft into the CW Mounting Nose as
indicated in 2nd photo below. (3) lock it using CW Shaft
Locking Screw from the other side of the CW
Mounting Nose. Tighten the Front CW Positioning
Screw which is located in front of the CW Mounting
Nose.
with a 10.4 lbs (4.7kg) counterweight. It should be
able to balance a payload of about 13 lbs (6kg). An
optional CW or Extension bar is available for heavier
payload.
7. Attach and Balance an OTA on the Mount: After
attaching an OTA and accessories to the mount, the
ZEQ25 mount must be balanced in both R.A. and
DEC to ensure minimum stress on the mount (such as
gears and motors inside).
CW Mounting Nose
CAUTION: The telescope may swing freely when
the R.A. or DEC Gear Switch is released. Always
hold on to the OTA before you release the gear
switch to prevent it from swinging. It can cause
personal injury or damage to the equipment.
(1)
Release Gear Switch Locking Screw by turning it 2
turns counterclockwise. Turn Gear Switch Knob 90
degree to OPEN position to disengage the worm from
the worm wheel.
CW Shaft Locking Screw
Front CW Position Screw
Gear Switch Locking Screw
Gear Switch
LOCK
OPEN
(3)
Rotate the DEC axis to horizontal position. Adjust the
CW position to balance the mount in R.A. axis and
move the OTA position to balance the mount along
DEC axis.
CW Shaft inserts into
CW mounting nose.
(2)
If the latitude of the observation location is lower than
10º, thread in the Rear CW Position Screw (a hex
head set screw) before tightening the Front CW
Positioning Screw to avoid CW hit tripod legs. Then
tighten the Front CW Positioning Screw.
R.A. balance
Rear CW Position Screw
6. Install Counterweight: Mount the CW onto CW shaft.
Tighten the CW Locking Screw to hold the CW in
place. Tighten the CW Safety Screw. ZEQ25 comes
DEC balance
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Return the mount to Zero Position after balance, i.e.
the CW shaft points to ground and telescope is at the
highest position.
Turn Gear Switch Knob 90 degree again to LOCK
position to re-engage the worm to the worm wheel.
Retighten the Gear Switch Locking Screw.
CAUTION: The balance process MUST be done
with Gear Switch at OPEN position! Otherwise it
might damage the worm system.
Polar Scope LED
8. Connect Cables: Connect DEC unit to the main
control unit with a short, straight RJ11 cable. Connect
the Go2Nova® 8408 hand controller to the HC port on
the main unit. Plug 12V DC power supply into the
POWER socket. The power indicator on the main unit
will be on when the power switch is turned on.
(2) Pressing the MENU button, then select “Align”
and “Pole Star Position” to display the Polaris
Position on the LCD screen, as indicated in the
left of the following figure. For example, May 30,
2010, 20:00:00 at Boston, US (alt N42º30’32” and
long W71º08’50”), 300 min behind UT, the Polaris
Position are 1h26.8m and 41.5m
9. Polar Alignment: In order for an equatorial mount to
track properly, it has to be accurately polar aligned.
Take off the Polar Axis Cover and Polar Scope Cover.
Look through the polar scope eyepiece to locate the
Polaris. Slightly turn tripod Center Rod Knob to loosen
the mount head. Adjust the Azimuth Adjustment
Knobs to do a fine adjustment of the mount to center
the polar star in the azimuth direction. Tighten the
Center Rod Knob to secure the mount. Slightly loosen
two Latitude Locking T-bolts on the side of the mount,
turning the Latitude Adjustment Knob to adjust the
latitude (altitude). Re-tighten the locking screws.
(If you are located at south hemisphere, Sigma
Octantis will be used as the reference for polar
alignment.)
(3) Using Azimuth Adjustment Knob and Latitude
Adjustment Knob to adjust the mount in altitude
and azimuth directions and put the Polaris in
same position on the Polar Scope Dial as
indicated on the HC LCD, as shown in Right of the
above figure.
Polar Axis Cover
Polar Axis (R.A. axis)
Lat. Locking T-bolt
Lat. Adj. Knob
If the mount is not equipped with a polar scope or the
pole star cannot be seen, you can use Polar
Alignment Procedure.
(1) Level the ZEQ25 mount and set it at Zero Position.
Make sure the telescope is parallel to the pole
axis (R.A. axis) of the mount. If a finder scope is
used, adjust it to be parallel to the telescope
optical axis. Set correct R.A. and DEC back lash
numbers. An eyepiece with cross hairs is
recommended.
(2) Power on the mount. Pressing the MENU button,
then select “Align” and “Polar Alignment”. The
HC will display the azimuth and altitude position of
several bright stars near meridian. Select one that
is visible from the site as aligning Star A. Follow
the instruction to move the Star A to the center of
the eyepiece with the combination of Latitude
Adjustment Knob and “◄” or “►” button. Press
ENTER to confirm. Then select a bright star that is
close to the horizon as aligning Star B. Center it
Polar Scope Cover
Azi. Adj. Knob
If the mount is equipped with iOptron’s AccuAligningTM
Polar Scope, you can do a fast and accurate polar
alignment.
Quick Polar Alignment
(1) Connect polar scope LED cable between Reticle
plug located on the main unit and the LED socket
at the bottom of the DEC axle. The illumination
intensity can be adjusted using the HC via “Set
Polar Scope Light” function under “Set Up
Controller” menu.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
using the Azimuth Adjustment Knob and “◄” or
“►” button (The “▲” and “▼” buttons do not work
here). Press ENTER to confirm.
capable cell phone or from internet. “W/E” means
western/eastern hemisphere; “N/S” means
northern/southern hemisphere; “d” means degree; “m”
means minute; and “s” means second. Use number
keys and arrow keys to enter your location information.
(3) The telescope will point to Star A again and
repeat above step until the error is minimum, or at
your decision. Press the BACK button to exit
alignment procedure.
Move the cursor to the end of the screen to select
Northern or Southern Hemisphere.
10. Manual Operation of the Mount: Now you can
observe astronomical objects using the arrow keys of
a Go2NovaTM hand controller. Flip the I/O switch on
the telescope mount to turn on the mount. Use
►,◄,▼ or ▲ buttons to point the telescope to the
desired object. Use the number keys to change the
slewing speed. Then press STOP/0 button to start
tracking.
12. One Star Alignment: Perform One Star Align to
correct the Zero Position discrepancy. To further
improve the GOTO accuracy, refer to the full manual
for more details.
13. Go to an Object: The mount is now ready to GOTO
and tracking targets. Press MENU button, select
“Select and Slew” and press ENTER. Select a
category (ex. “planets, sun, moon”). Then select an
object (ex. “moon”). Then press ENTER. The
telescope will automatically slew to the object and
start tracking.
11. Setup Controller: The time and site information of the
observation location needs to be entered for precise
GOTO.
Turn the mount power on. Wait for controller lights on.
Press the MENU button. Move the cursor to “Set Up
Controller” and press ENTER. Select “Set Up Time
& Site” and press ENTER.
14. Sync to Target: If the star is not in the center of the
eyepiece, one can use this function to center and
synchronize the object to improve the local GOTO
accuracy. Press MENU button and select “Sync. To
Target.” Press ENTER. Next use the arrow keys to
move object until it is centered in your eyepiece. Then
press ENTER again on the hand controller. A Select
and Slew has to be performed before “Sync to
Target” operation. This is most useful if you are
looking for some faint objects near a bright star.
“Sync to Target” is similar to “one star alignment”.
15. Identify Nearby Bright Objects: After slewing to an
object using hand controller, a list of nearby bright
object(s) will be displayed by pressing the “?” button.
Enter the date and check if it is Daylight Saving Time
using arrow keys and number keys. Enter your time
zone (add or subtract 60 minutes per time zone) by
entering minutes “behind” UT or “ahead of” UT, such
as:
16. Adjust Gear Mesh Tension: The Gear Switch
Locking Screws also serve as gear mesh tensing
adjusters. You may adjust R.A. and/or DEC gear
meshing tension by turn the Gear Switch Locking
Screws as needed.
•
•
•
•
Boston is 300 minutes “behind” UT
Los Angeles is 480 minutes “behind” UT
Rome is 60 minutes “ahead” of UT
Sydney is 600 minutes “ahead” of UT
All the time zones in North America are “behind” UT.
You may also find your observation longitude and
latitude coordinate from your GPS navigator, a GPS
For technical support you can email
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IOPTRON TWO YEAR TELESCOPE, MOUNT, AND CONTROLLER WARRANTY
A. iOptron warrants your telescope, mount, or controller to be free from defects in materials and workmanship for two years. iOptron will
repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workmanship. As a
condition to the obligation of iOptron to repair or replace such product, the product must be returned to iOptron together with proof-of-
purchase satisfactory to iOptron.
B. The Proper Return Merchant Authorization Number must be obtained from iOptron in advance of return. Call iOptron at
1.781.569.0200 to receive the RMA number to be displayed on the outside of your shipping container.
All returns must be accompanied by a written statement stating the name, address, and daytime telephone number of the owner,
together with a brief description of any claimed defects. Parts or product for which replacement is made shall become the property of
iOptron.
The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of iOptron, and shall be
required to prepay such costs.
iOptron shall use reasonable efforts to repair or replace any telescope, mount, or controller covered by this warranty within thirty days of
receipt. In the event repair or replacement shall require more than thirty days, iOptron shall notify the customer accordingly. iOptron
reserves the right to replace any product which has been discontinued from its product line with a new product of comparable value and
function.
This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function, or
subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to normal wear is not
covered by this warranty.
IOPTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF FITNESS FOR A
PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HERE. THE SOLE OBLIGATION OF IOPTRON UNDER THIS LIMITED
WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH
HERE. IOPTRON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE
ANY IOPTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED
IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied
warranty lasts, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
iOptron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.
If warranty problems arise, or if you need assistance in using your telescope, mount, or controller contact:
iOptron Corporation
Customer Service Department
6F Gill Street
Woburn, MA 01801
Tel. (781)569-0200
Fax. (781)935-2860
Monday-Friday 9AM-5PM EST
NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an authorized iOptron dealer in
the U.S.A. or Canada or directly from iOptron. Warranty outside the U.S.A. and Canada is valid only to customers who purchased from
an iOptron Distributor or Authorized iOptron Dealer in the specific country. Please contact them for any warranty.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|