2400DSV
Service Manual
___________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
PREFACE
This Service Manual explains the Microfilm Scanner already put on the
market.
It is hoped that this Service Manual will help to provide for more effective
machine maintenance in the field there by ensuring optimum machine
performance.
Microfilm Scanner MS6000
All information in this Manual is subject to change without prior notice.
This manual has not described the printer section.
Separately, refer to the Service Manual of the Printer.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
2
3
Safety Precautions for Inspection and Service
1.1 WARNING.............................................................................................. 1
1.2 CAUTION............................................................................................... 4
1.3 Other Precautions................................................................................ 6
Installation
2.1 Installation Environment ..................................................................... 8
2.2 Usage Environment ............................................................................. 8
2.4 Installation Space................................................................................. 9
General Information
3.1 Specifications..................................................................................... 10
3.1.1 MS 6000........................................................................................ 10
3.1.3 MS 6000 & MSP2000 Printer System ........................................... 12
3.2 System Configuration........................................................................ 13
3.3 Connection Mode............................................................................... 14
3.4 Parts Identification............................................................................. 15
3.5 Component Layout ............................................................................ 16
3.6 Electrical Components Layout ......................................................... 17
3.7 Electrical Parts Function................................................................... 20
3.8 Connectors Layout ............................................................................ 22
3.9 Electrical Service Parts on P.W.Boards........................................... 24
3.9.1 Main Control Board (PWB-BB)...................................................... 24
3.9.2 I/F Board (PWB-EE)...................................................................... 24
3.9.3 I/F Board (PWB-SS)...................................................................... 25
3.9.4 Main Power Unit (PU1).................................................................. 25
3.9.5 Projection Lamp Regulator (PU2) ................................................. 25
3.9.6 Optional Power Unit (PU3)............................................................ 25
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3.11Image Processing...............................................................................35
4
Mechanical and Electrical
4.1.1 Overview........................................................................................37
4.1.6 Projection Lens ..............................................................................41
4.2 Image Rotation....................................................................................42
4.2.1 Prism Rotation ...............................................................................42
4.2.2 Auto Image Rotating Motor (M5) Control Circuit............................42
4.3 Optical Section ...................................................................................43
4.3.1 Overview........................................................................................43
4.3.2 Reader Path...................................................................................44
4.3.3 Scan Path ......................................................................................44
4.4 CCD Section........................................................................................48
4.5 Image Bus ...........................................................................................49
4.6 Auto Masking......................................................................................52
4.6.1 Overview........................................................................................52
4.6.2 Masking Area Detection.................................................................52
4.7 Auto Image Skew Correction.............................................................55
4.7.1 Overview........................................................................................55
4.7.2 Requirements for Auto Skew Correction........................................55
4.8 Manual Frame Masking......................................................................56
4.9 2 to 1 Printing Function .....................................................................57
4.9.1 Overview........................................................................................57
4.9.2 Operation .......................................................................................57
4.9.3 Identification Marks........................................................................58
5
Disassembly and Cleaning
5.1 Precautions.........................................................................................59
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5.4.3 Cleaning of the Projection Lamp ................................................... 66
5.4.5 Cleaning of the each Mirrors ......................................................... 67
5.4.9 Removal of the P.W.Boards.......................................................... 72
5.4.12 Replacing the Main Fuse............................................................... 74
6
Function Mode and Adjustment
6.1 Precautions......................................................................................... 77
6.2 Overview ............................................................................................. 77
6.3 Function Mode List ............................................................................ 78
6.3.2 y mode (Setting Function 2) .......................................................... 79
6.3.6 About the Function Mode Setting Label ........................................ 82
6.4 Operation of the Function Mode....................................................... 83
6.4.1 Entering the Function Mode .......................................................... 83
6.4.2 Execution method in F and b mode (except F4, F8 and b6) ......... 83
6.4.3 Execution method in F and b mode (F4, F8 and b6)..................... 84
6.4.4 Execution method in S, y and o mode........................................... 84
6.4.5 Leaving the Function Mode........................................................... 84
6.5 S mode Operations ............................................................................ 85
6.5.1 S1: Auto Reset .............................................................................. 85
6.5.2 S2: Auto Power Save .................................................................... 85
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
6.5.12 SC: Scan Table Stop Position Adjustment (Reader Position)........88
6.6 y mode Operations.............................................................................90
6.7 o mode Operations.............................................................................92
6.7.9 oA: Host Driver Setting ..................................................................98
6.8 F mode Operations.............................................................................99
6.8.3 F3: Print Counter............................................................................99
6.8.4 F4: Counter Clear ..........................................................................99
6.8.5 F5: Control Panel LED Check........................................................99
6.8.6 F6: For Factory use........................................................................99
6.8.7 F7: Projection Lamp Voltage Adjustment.....................................100
6.8.8 F8: Reset the Setting Data..........................................................101
6.9 b mode Operations...........................................................................102
6.9.1 b1: Checking the Scan Table Unit Function.................................102
6.9.2 b2: Scanning mirror operation check ...........................................102
6.9.3 b3: For Factory use......................................................................102
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
6.9.6 b6: Shading Correction................................................................ 104
7
7.3.5 C4: Cooling Fan Motor malfunction............................................. 109
7.4 Troubleshooting for malfunction code .......................................... 110
7.5 Troubleshooting for malfunction.................................................... 113
7.5.1 No Power..................................................................................... 113
7.6.4 PC1: Image Leading Edge Sensor.............................................. 114
7.6.5 PC2: Scan Mirror Position Sensor............................................... 114
7.6.6 PC3: Reader Position Sensor ..................................................... 115
7.6.7 PC4: Scan Position Sensor......................................................... 115
7.6.8 PU1: Power Unit.......................................................................... 115
7.6.9 PU2: Projection Lamp Regulator................................................. 115
7.6.10 S1: Power Switch ........................................................................ 115
7.6.11 S201: Interlock Switch................................................................. 116
7.6.12 TS1: Thermostat.......................................................................... 116
7.7 Image Troubleshooting ................................................................... 117
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
1
1
Safety Precautions for Inspection and
Service
When performing inspection and service procedures, observe the
following precautions to prevent accidents and ensure utmost safety.
*Depending on the model, some of the precautions given in the following
do not apply.
Different markings are used to denote specific meanings as detailed
below.
Indicates a potentially hazardous situation which, if
WARNING
CAUTION
not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
The following graphic symbols are used to give instructions that need to
be observed.
Used to call the service engineer attention to what is graphically
represented inside the marking (including a warning).
Used to prohibit the service engineer from doing what is
graphically represented inside the marking.
Used to instruct the service engineer to do what is graphically
represented inside the marking.
1.1
WARNING
1. Always observe precautions.
• Parts requiring special attention in this product will include a
label containing the mark shown on the left plus
precautionary notes. Be sure to observe the precautions.
• Be sure to observe the “Safety Information” given in
Operator’s Manual.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
1
2. Before starting the procedures, be sure to unplug the power cord.
• This product contains a high-voltage unit and a circuit with a
large current capacity that may cause an electric shock or
burn.
• The product also contains parts that can jerk suddenly and
cause injure.
• If this product uses a laser, laser beam leakage may cause
eye damage or blindness.
3. Use the specified parts.
• For replacement parts, always use the genuine parts
specified in the manufacturer’s Parts Manual. Installing a
wrong or unauthorized part could cause dielectric
breakdown, overload, or undermine safety devices resulting
in possible electric shock or fire.
• Replace a blown electrical fuse or thermal fuse with its
corresponding genuine part specified in the manufacturer’s
Parts Manual. Installing a fuse of a different make or rating
could lead to a possible fire. If a thermal fuse blows
frequently, the temperature control system is probably of a
problem and action must be taken to eliminate the cause of
the problem.
4. Handle the power cord with care and never use a multiple socket.
• Do not brake, crush or otherwise damage the power cord.
Placing a heavy object on the power cord, or pulling or
bending it may damage it, resulting in a possible fire or
electric shock.
• Do not use a multiple outlet to which any other appliances
or machines is connected.
• Be sure the power outlet meets or exceeds the specified
capacity.
5. Be careful about the high-voltage parts.
• A part marked with the symbol shown on the left carries a
high voltage.
Touching it could result in an electric shock or burn. Be sure
to unplug the power cord before servicing this part or the
parts near it.
6. Do not keep your hands wet when performing the procedures.
• Do not unplug or plug in the power cord, or perform any
kind of service or inspection with wet hands. Doing so could
result in an electric shock.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
7. Do not touch a high-temperature part.
1
• A part marked with the symbol shown on the left and other
parts such as the exposure lamp and fusing roller can be
very hot while the machine is energized. Touching them
may result in a burn.
• Wait until these parts have cooled down before replacing
them or any surrounding parts.
8. Make a ground connection at all times
(This item may not be effected in USA).
• Be sure to connect a ground wire to the ground terminal
even when performing an inspection or repair. Without
proper grounding, electrical leakage could result in an
electric shock or fire.
• Never connect the ground wire to a gas pipe, water pipe,
telephone ground wire, or a lightning conductor.
9. Do not remodel the product.
• Modifying this product in a manner not authorized by the
manufacturer may result in a fire or electric shock. If this
product uses a laser, laser beam leakage may cause eye
damage or blindness.
10. Restore all parts and harnesses to their original positions.
• To promote safety and prevent product damage, make
sure the harnesses are returned to their original positions
and properly secured in their clamps and saddles in order
to avoid hot parts, high-voltage parts, and sharp edges, or
being crushed.
• To promote safety, make sure that all tubing and other
insulating materials are returned to their original positions.
Make sure that floating components mounted on the
circuit boards are at their correct distance and position off
the boards.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
1
1.2
CAUTION
1. Precautions for Service Jobs
• A toothed washer and spring washer, if used originally, must
be reinstalled.
Omitting them may result in contact failure which could
cause an electric shock or fire.
• When reassembling parts, make sure that the correct
screws (size, type) are used in the correct places. Using the
wrong screw could lead to stripped threads, poorly secured
parts, poor insulating or grounding, and result in a
malfunction, electric shock or injury.
• Take great care to avoid personal injury from possible burrs
and sharp edges on the parts, frames and chassis of the
product.
• When moving the product or removing an option, use care
not to injure your back or allow your hands to be caught in
mechanisms.
2. Precautions for Servicing with Covers and Parts Removed
• Wherever feasible, keep all parts and covers mounted when
energizing the product.
• If energizing the product with a cover removed is absolutely
unavoidable, do not touch any exposed live parts and use
care not to allow your clothing to be caught in the moving
parts. Never leave a product in this condition unattended.
• Never place disassembled parts or a container of liquid on
the product parts falling into, or the liquid spilling inside, the
mechanism could result in an electric shock or fire.
• Never use a flammable spray near the product. This could
result in a fire.
• Make sure the power cord is unplugged before removing or
installing circuit boards or plugging in or unplugging
connectors.
• Always use the interlock switch actuating jig to actuate an
interlock switch when a cover is opened or removed. The
use of folded paper or some other object may damage the
interlock switch mechanism, possibly resulting in an electric
shock, injury or blindness.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
3. Precautions for Working Environment
1
• The product must be placed on a flat, level surface that is
stable and secure.
• Never place this product or its parts on an unsteady or
tilting workbench when servicing.
• Provide good ventilation at regular intervals if a service job
must be done in a confined space for a long period time.
• Avoid dusty locations and places exposed to oil mist or
steam.
• Avoid working positions that may block the ventilation port
of the product.
4. Precautions for Handling Batteries
• Replace a rundown battery with the same type as specified
in the manufacturer’s parts manual.
• Before installing a new battery, make sure of the correct
polarity of the installation or the battery could burst.
• Dispose of used batteries according to the local regulations.
Never dispose of them at the user’s premises or attempt to
try to discharge one.
5. Precautions for Laser Beam (Products Employing Laser Only)
• Removing the cover marked with the following caution label
could lead to possible exposure to the laser beam, resulting
in eye damage or blindness. Be sure to unplug the power
cord before removing this cover.
• If removing this cover while the power is ON is unavoidable,
be sure to wear protective laser goggles that meet
specifications.
• Make sure that no one enters the room when the machine
is in this condition.
• When handling the laser unit, observe the “Precautions for
Handling Laser Equipment.
DANGER
Invisible laser radiation when open.
AVOID
DIRECT
EXPOSURE
TO BEAM
0947-7127-01
1144D270AA
1167P001AA
.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
1
1.3
Other Precautions
• To reassemble the product, reverse the order of disassembly unless otherwise
specified.
• While the product is energized, do not unplug or plug connectors into the circuit
boards or harnesses.
• The magnet roller generates a strong magnetic field. Do not bring it near a
watch, floppy disk, magnetic card, or CRT tube.
• An air gun and vacuum cleaner generates a strong electrostatic charge that can
destroy the ATDC sensor and other sensors. Before cleaning a component with
one of these devices, be sure to remove all the sensors. Otherwise, use a
blower brush and cloth when cleaning parts.
• When handling circuit boards with MOS ICs, observe the “INSTRUCTIONS
FOR HANDLING THE PWBs WITH MOS ICs” (applicable only to the products
using MOS ICs).
• The PC Drum is a very delicate component. Observe the precautions given in
“HANDLING OF THE PC DRUM” because mishandling may result in serious
image problems.
• Note that replacement of a circuit board may call for readjustments or resetting
of particular items, or software installation.
• After completing a service job, perform a safety check. Make sure that all parts,
wiring and screws are returned to their original positions.
• Check the area surrounding the service site for any signs of damage, wear or
need of repair.
• Do not pull out the toner hopper while the toner bottle is turning. This could
result in a damaged hopper motor or locking mechanism.
• If the product is to be run with the front door open, make sure that the toner
hopper is in the locked position.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions for Inspection and Service
1
1.4
Used Batteries Precautions
(ALL Areas)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
(Germany only)
VORSICHT!
Explosinsgefahr bei unsachgemäßen austausch der batterie.
Ersatz nur durch denselben oder einen vom hersteller empfohlenen
ähnlichen typ.
Entsorgung gebrauchter batterien nach angaben des herstellers.
(France)
ATTENTION
Ily a danger d’explosion s’ily a remplacement incorrec de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un type
équivalent recommande par le constructueur.
Mettre au rebut les batteries usageés conformément aux instructions du
fabricant.
(Denmark only)
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering Udskiftning må
kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
(Norway only)
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende type anbefalt av
apparatfabrikanten.
Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
(Sweden only)
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent typ som rekommenderas av
apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
(Finland only)
VAROlTUS
Paristo voi räjähtää, los se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä Käytetty paristo valmistajan ohjeiden mukaisesti.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2
2
Installation
2.1
Installation Environment
To ensure safety and utmost performance of the machine, the machine
should not be used in a place.
1. Where it will be subject to extremely high or low temperature or
humidity.
2. Which is exposed to direct sunlight.
3. Which is in the direct air stream of an air conditioner, heater, or
ventilator.
4. Which puts the operators in the direct air stream of exhaust of the
machine.
5. Which has poor ventilation.
6. Where ammonia gas might be generated.
7. Where it will be subject to sudden fluctuations in either temperature or
humidity.
8. Which is near any kind of heating device.
9. Which does not have stable, level floor.
10. Where it may be splashed with water.
11. Which is dirty or where it will receive undue vibration.
12. Which is near volatile flammables or curtains.
NOTE:
➜
If the machine is placed near a window, insure that the Screen faces
inside, not the window.
2.2
Usage Environment
In order to make sure the machine functions in good condition, please
make sure the ambient environment satisfies the following requirements:
Temperature: 10-35°C Temperature fluctuation: 10°C per hour or less
Humidity: 15-85%
Humidity fluctuation: 20% per hour or less
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2
2.3
Installing The Power Supply
1. Do not plug the Power Cord into a power outlet via an extension cord
supplying electricity to more than one unit.
2. Do not connect the machine to a power outlet used for other
equipment or appliances.
3. More than one appliance connected to a single outlet could cause a
drop or surge in the electrical supply, resulting in operational problems
for the machine.
G
Voltage fluctuation:Specified voltage: 10%
G
Frequency fluctuation:Specified frequency: 3Hz
4. The following items should be checked periodically:
G
G
G
Make sure the power supply plugs do not feel warm.
Power supply cords should be free of cracks and scratches.
Power supply plugs should be firmly plugged into outlets.
2.4
Installation Space
To ensure easy machine operation, replacement of consumables, and
maintenance service jobs, provide the following space for the installation
of the machine.
Allow the enough space around the louver to keep the good ventilation.
100 mm
or 4”
503mmor
19-3/4”
100 mm
or 4”
100 mm or 4”
821 mm or 32-3/8”
9
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3
General Information
3.1
Specifications
3.1.1 MS 6000
Specifications
Type:
Desk-Top Type Microfilm Scanner
Type of Film:
Microfiche, Aperture Card, Jacket, Roll Films (16 mm, 35 mm),
16mm Cartridge Film both Positive and Negative
Magnification:
Single Lens......... 7.5X
Zoom Lens......... 9X-16X, 13X-27X, 23X-50X
Screen Size
300 mm X 300 mm or 12" X 12" (Scanning Area)
Image Rotation
Prism Rotation
Carrier Rotation (Fiche Carrier 5 only)
Resolution:
200, 300, 400, 600, 800 dpi (PC Mode)
400, 600 dpi (PR Mode: When MSP 3000 Printer is connected)
400 dpi (PR Mode: When MSP 2000 Printer is connected)
Scanning Method
Scanning Speed
Scanning/Scanning direction: CCD scanning
Scanning/Feeding direction: Mirror scanning
6.5 sec./1 frame scanning
5.5 sec./Multi-frame scanning
(8-1/2" X 11" or A4 Lengthwise, 400dpi, AE)
Exposure Setting
2 way Settings:
Automatic Control & Manual Control
N-P/P-P Select
Scanning Mode
Output Scale:
Auto/Manual Select
Text/Photo/Fine
PC Mode: Binary, Grayscale (Option)
PR Mode: Binary
PC Interface:
SCSI-2 (Option)
Auto Edit Function
Auto Frame Masking, Auto Centering, Auto Skew Correction, Fit,
Trimming, Masking, Electrical Zoom, Electrical Image Rotation
Light Source
Halogen Lamp (20V 150W DDL Type)
120VAC (60Hz), 220/240VAC (50-60Hz)
Less than 350W (with all options)
Power Requirement
Power Consumption
B.T.U
(British Thermal Unit)
900 BTU (Reader Mode)
850 BTU (Scan Mode)
Acoustic noise
Dimensions
Weight
53 dB or less (Scanning)
50 dB or less (Reader)
503 mm (W) x 821 mm (D) x 716 mm (H) or
19-3/4" (W) x 32-3/8" (D) x 28-1/4" (H)
39 Kg or 86 lbs
10
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
Specifications
Standard Accessories
Options:
Power Cord, Printer Cable, Operator’s Manual
Lenses, Prism Unit, Fiche Carrier 5, Universal Carrier UC-2, Roll
Film Carrier 9B, Roll Film Carrier 15A/15M, Roll Film Carrier 21,
MARS Controller 4, MARS Mini Controller 2, Manual Frame
Masking Kit, Counter Kit, Foot Switch Kit, PC Interface Kit,
Grayscale Memory Board
11
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.1.2 MS 6000 & MSP3000 Printer System
Specifications
Type:
Microfilm Scanner Printer System
Laser Electrostatic
Printing Method:
Resolution:
Print Size:
400, 600 dpi
8-1/2" × 11" (or A4) Crosswise, 11" × 17" (or A3) Lengthwise
8-1/2" × 11" (or A4) Lengthwise, 8-1/2" × 14" (or B4) Lengthwise
Print Speed:
20 sheets per minute (8-1/2" × 11" or A4: Crosswise)
13 seconds (8-1/2" × 11" or A4: Crosswise)
Less than 70 seconds
First Print Time:
Warm-up Time:
Multiple Printing:
Paper Supply:
1-19 sheets (LED countdown identification)
Automatic Feeding System
Paper Feeding Tray (250 sheets max.)
Paper Cassette 1 (250 sheets max.)
Paper Cassette 2 (250 sheets max.): Option
Power Consumption:
Printer‘s Dimensions
Less than 1100W (Scanner: 350W, Printer: 750W)
561mm (W) x 521mm(D) x 409 mm (H) or
22" (W) x 20-1/2" (D) x 16" (H)
Printer‘s Weight
Printer’s Option:
28 Kg or 61-3/4 lbs (including Imaging Cartridge)
Second Paper Cassette Unit
3.1.3 MS 6000 & MSP2000 Printer System
Specifications
Type:
Microfilm Scanner Printer System
Laser Electrostatic
Printing Method:
Resolution:
400 dpi
Print Size:
8-1/2" × 11" (or A4)
Print Speed:
First Print Time:
Warm-up Time:
Multiple Printing:
Paper Supply:
8 sheets per minute (8-1/2" × 11" or A4)
19 seconds (8-1/2" × 11" or A4)
Less than 20 seconds
1-19 sheets (LED countdown identification)
Automatic Feeding System
Multipurpose tray (150 sheets max.)
Power Consumption:
Printer’s Dimensions
Less than 930W (Scanner: 350W, Printer: 580W)
394 mm(W) x 446 mm(D) x 328 mm(H) or
15-1/2"(W) x 17-1/2"(D) x 13"(H)
Printer’s Weight
Printer’s Option:
17 lbs. (7.8kg) <Including Toner/Drum Cartridge>
Face-Up Tray
12
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.3
Connection Mode
This Scanner is available in the following configurations.
3.3.1 PR Mode (Scanner + Printer)
The Scanner is connected to a dedicated printer, allowing scanned
images to be printed out directly.
MSP3000 Printer
MSP2000 Printer
Each scanner is designed exclusively for use with its respective Printer.
3.3.2 PC Mode (Scanner + Personal Computer)
The Scanner is connected to a personal computer and the scanned
images can be uploaded to the computer. An optional PC interface kit
required for connection to a personal computer.
Connection to a personal computer and printer can be switched using
Control Panel.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.4
Parts Identification
1
2
3
4
5
13
6
12
7
8
11
9
10
1. Screen
2. Control Panel
3. Option Interface Connector (option)
4. Fuse Holder
5. Power Cord Socket
6. Printer Connector
7. SCSI Connector
8. Power Switch
9. Projection Unit
10. Image Rotation Knob
11. Fiche Carrier 5 (option)
12. Brightness Select Lever
13. Projection Lens (option)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.5
Component Layout
1
3
2
4
5
6
7
8
9
10
1. 1st Reader Path Mirror
2. 2nd Reader Path Mirror
3. 2nd Scan Path Mirror
4. Screen
6. Scan Table
7. Projection Lens
8. Projection Lamp
9. 3rd Scan Path Mirror
10. CCD Assy
5. 1st Scan Path Mirror
16
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
Symbol
F1
Name
Fuse
L1
Filter Coil
LA1
Projection Lamp
M1
Scan Motor
M2
Scan Table Motor
Power Unit Cooling Fan Motor
Projection Lamp Cooling Fan Motor
Image Leading-Edge Position Sensor
Scan Mirror Position Sensor
Reader Position Sensor
Scan Position Sensor
Main Power Unit
M3
M4
PC1
PC2
PC3
PC4
PU1
PU2
Projection Lamp Regulator
CCD Board
PWB-A
PWB-BB
PWB-C
PWB-EE
PWB-G
PWB-J
PWB-SS
PWB-T
S1
Main Control Board
Control Panel Board
Printer I/F Board
Scan Table Connecting Board
Grayscale Memory Board
PC I/F Board
Motor Drive Board
Power Switch
S201
TS1
Interlock Switch
Thermostat
*PWB-J, PWB-SS : Option
18
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
PWB-D
(PWB-F)
PU-3
PWB-Y
VR1
M5
PWB-X
CNT1
Symbol
CNT1
M5
Name
Total Counter
Auto Image Rotation Motor
PU3
Option Power Unit (for RFC-21)
PWB-D
PWB-F
PWB-X
PWB-Y
VR1
Option I/F Board (for RFC-15A/M, UC-2, MARS)
Option I/F Board (for RFC-21, UC-2, MARS)
Manual Masking Board
Manual Masking Board
Auto Image Rotation Volume
*CNT1, PU3, PWB-D, PWB-F, PWB-X, PWB-Y : Option
19
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.7
Electrical Parts Function
Symbol
CNT1
F1
Name
Function
Total Counter
Fuse
Counts the number of prints.
Power Fuse
100/120V Area: 250V, 10A
220-240V Area: 250V, 6.3A
L1
Filter Coil
Power-supply noise filter
LA1
Projection Lamp
The source of the light for projecting the film
image
M1
Scan Motor
The motor which rotate the 1st scanning
mirror when carrying out scan of the film
image to CCD.
M2
M3
M4
Scan Table Motor
The motor for moving a scanning table to a
reader position and a scanning position.
Power Unit Cooling Fan Motor Exhausts the heated air surrounding the
Power Unit out of the machine.
Projection Lamp Cooling Fan
Motor
Exhausts the heated air surrounding the
Projection Lamp out of the machine.
M5
Auto Image Rotation Motor
The motor which rotate a prism.
PC1
Image Leading-Edge Position Detects the slit on the Scan Mirror mounting
Sensor
plate.
Leading-edge detect :L
PC2
PC3
PC4
PU1
PU2
PU3
Scan Mirror Position Sensor
Reader Position Sensor
Scan Position Sensor
Main Power Unit
Detects the home position of the Scan Mirror.
Scan Mirror home position detect :L
Detects the reader position of the Scan Table.
Reader position detect :L
Detects the scan position of the Scan Table.
Scan position detect :L
Converts the power voltage from AC voltage
into DC voltage.
Projection Lamp Regulator
Converts the power voltage from AC voltage
into DC voltage and supplies that to LA1.
Option Power Unit
(for RFC-21)
Converts the power voltage from AC voltage
into DC voltage (DC-24V) and supplies that to
optional RFC21.
PWB-A
CCD Board
The CCD reads the film image.
Controls all machine operation.
PWB-BB Main Control Board
PWB-C
Control Panel Board
The keys and LEDs which make operation of
the machine possible are included.
PWB-D
Option I/F Board
The Interface board which connects an option
(RFC, MARS).
PWB-EE Printer I/F Board
PWB-F Option I/F Board
Communicates with the Main Control Board
and printer.
Communicates with the Main Control Board
and option (MARS, RFC).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
Symbol
Name
Function
PWB-G
Scan Table Connecting Board Connects the Scan Table Section and Main
Harness of the machine.
PWB-J
Grayscale Memory Board
PC Mode:
Memory used when image is read with
Grayscale.
PR Mode:
Memory used when image is read by print
reserve function.
PWB-SS PC I/F Board
Communicates with the Personal Computer
and machine.
PWB-T
PWB-X
Motor Drive Board
The substrate which controls the motors.
Manual Masking Board
(Horizontal)
The substrate which specifies the Masking
position of the horizontal direction.
PWB-Y
Manual Masking Board
(Vertical)
The substrate which specifies the Masking
position of the vertical direction.
S1
Power Switch
Turns ON or OFF the machine.
S201
Interlock Switch
Detects the removing or installing of the
Projection Unit.
TS1
VR1
Thermostat
Cuts off the current to the Projection Lamp
(LA1) when it detects overheating.
(Rating: 195°C)
Auto Image Rotation Volume
The Volume which adjusts the rotation
direction and the speed of an auto image
rotation motor (M5).
CNT1, PU3, PWB-D, PWB-F, PWB-J, PWB-SS, PWB-X, PWB-Y: Option
21
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.8
Connectors Layout
CN1 3P
CN2 2P
CN3 2P
CN4 4P
CN5 2P
CN6 2P
CN7 3P
CN8 2P
CN10 3P
CN11 6P
CN12 12P
CN15 3P
CN17 5P
CN18 3P
CN19 2P
CN21 4P
CN40 6P
CN41 3P
CN42 3P
CN43 6P
PJ10 3P
PJ11 3P
PJ12BB 4P
PJ1C 28P
PJ2C 3P
PJ1T 4P
PJ2T 32P
PJ3T 9P
PJ1EE 60P
PJ2EE 80P
PJ3EE 50P
PJ4EE 40P
PJ1G 20P
PJ2G 20P
PJ1SS 80P
PJ2SS 50P
PJ1A 4P
PJ2A 20P
PJ3A 10P
PJ1BB 3P
PJ2BB 20P
PJ3BB 10P
PJ4BB 24P
PJ5BB 32P
PJ6BB 60P
PJ7BB 26P
PJ8BB 30P
PJ9BB 18P
PJ10BB 7P
PJ11BB 11P
PJ4T 8T
PJ5T 6T
PJ1PU1 3P
PJ2PU1 4P
PJ3PU1 6P
PJ4PU1 3P
PJ1PU2 3P
PJ2PU2 4P
PJ3PU2 2P
PJ1PU3 5P
PJ1PU3 6P
PJ2PU3 4P
*PJ9BB, PJ12BB: Not Used
22
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
CN13 9P
CN20 11P
CN28 6P
CN75 8P
CN76 9P
CN77 8P
CN78 9P
PJ1D/F 5P
PJ2D/F 13P
PJ3F 2P
PJ1X 8P
PJ2X 9P
PJ1Y 8P
PJ2Y 9P
23
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.9
Electrical Service Parts on P.W.Boards
NOTE
Do not touch the electric parts which has not indicated of this section.
3.9.1 Main Control Board (PWB-BB)
DSW1
DSW1...For Factory Use Only
(Normally all switches are OFF position.)
*Do not change to ON position.
3.9.2 I/F Board (PWB-EE)
OSC2 OSC1
OSC1 ...Oscillator (42.3158MHz): For 400dpi Printer
OSC2 ...Oscillator (95.2106MHz): For 600dpi Printer
24
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.9.3 I/F Board (PWB-SS)
RSW1
RSW1..For SCSI ID setting
3.9.4 Main Power Unit (PU1)
VR61: For Factory use *Do Not Touch
VR62: For Factory use *Do Not Touch
VR63: For Factory use *Do Not Touch
VR61
VR63
VR62
F1: Fuse
AC250V 12A (100/120V area)
AC250V 6.3A (220/240V area)
F1
3.9.5 Projection Lamp Regulator (PU2)
VR61: Projection Lamp voltage adjustment
F1
VR62: For Factory use *Do Not Touch
VR63: For Factory use *Do Not Touch
VR61
F1: Fuse
AC125V 5A (100/120V area)
AC250V 5A (220/240V area)
VR63
VR62
3.9.6 Optional Power Unit (PU3)
VR1: For Factory use *Do Not Touch
VR1
25
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.10 Explanation of Control Panel
3.10.1 Control Panel (Basic)
Output
Selection
Tray
1
Cassette1
Cassette2
Auto Skew
Correction
2
3
Centering/Fit
Auto
Manual
Masking
4
5
Text
Print Mode
Fine
Photo
Resolution
Auto
Nega
Posi
Film Type
6
7
Job Recall
Darker
9
Zoom +
Auto
8
Zoom clr
Lighter
7
Zoom -
10
12
13
11
15
C
14
16
PC/PR
Shift
Start
26
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
1. Size Selection Key: Select the paper feeding source according to the format
of the film image that is being reflected in the screen.
:
when this lamp is lit:
A 90 degree image rotation is performed dur-
ing printing.
The image on the screen will be rotated 90
degrees. Consequently, the screen image
will be oriented horizontally on paper that is
positioned lengthwise, and vertically on pa-
per that is positioned crosswise.
when this lamp is blink:
The Auto Film Format Select Print function is
available when Letter (or A4) size paper is
placed in both lengthwise and crosswise po-
sitions in the paper feeding tray and paper
feeding cassette. Paper that best suits the
format of the image on the screen will be
used for printing.
Tray:
Prints the film image on paper fed from the
print tray.
Cassette1: Prints the film image on paper fed from the
cassette 1.
Cassette2: Prints the film image on paper fed from the
cassette 2. (when the Tray and Cassette1
indicators are both lit)
2. Auto Skew
Correction Key:
This key is used to turn the Auto Skew Correction func-
tion ON or OFF. When this function is applied, the Auto
Skew Correction indicator will turn on and the system
will correct any skew of the image during printing.
*
After printing, the skew can be reset or retained.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3. Centering/Fit Key: When this key is pressed, the setting rotates from OFF
to the Centering and Fit functions.
When Auto Masking, Trimming, or Masking are set to
off, Auto Masking will automatically be enabled when
Centering is selected.
Centering:
Places a screen image that had been searched
using Auto masking or an image that has been
trimmed in the center of the page.
Fit:
Enlarges a screen image that had been searched
using Auto masking or an image that has been
trimmed to fit the page.
*When Masking
is selected or when the
Scanner is connected to the PC, this mode cannot
be used.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
4. Masking Key:
3
When pressed, this key rotates from OFF to the Auto,
Trimming or Masking functions.
Each time this key is pressed, selection is switched in
order of "OFF → Auto Masking → Manual Trimming →
Manual Masking → OFF."
Auto Masking:
The Auto Masking function will omit the frame
(non-image area) of a printed film image.
•
•
The previous Centering/Fit setting is applied when-
ever ON is selected from the OFF state.
If OFF is selected from the ON state, Centering/Fit
is disabled.
*
Auto Masking is not applicable with the Masking or
Trimming settings.
Trimming:
When ON is selected, the image is printed
(scanned) with the non-image area (frame) auto-
matically masked.
Masking:
Prints only the image outside of the area that is de-
fined on the Screen.
•
•
•
If Trimming is selected from the OFF state, the pre-
viously entered settings for Centering/Fit and Man-
ual Masking are applied.
From Trimming, when Masking is selected, the
Centering/Fit setting is disabled and the previous
settings for the Masking area are applied.
The manual masking area will be cancelled when-
ever OFF is selected from the Masking state.
*
*
Neither Trimming nor Masking are available through
the Auto Masking function.
Trimming and Masking cannot be set when the
Scanner is connected to the PC.
5. Print Mode Key:
Allows you to fine tune the image quality of the print ac-
cording to the original being used. Rotate between
Text, Fine and Photo with every press of this key.
Text:
Fine:
For use with text images.
For use with lower grades of film.
Photo: For use with photo images.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
6. Film Type Key:
Rotates between Auto, Nega, and Posi each time the
key is pressed.
Auto:
The scanner automatically determines be-
tween the film type options of negative or pos-
itive for print production.
Nega: Select when using negative film. Dark and
light values of the print will be reversed.
Posi:
Select when using positive film. Dark and light
values of the print will be consistent with the
image on film.
7. Exposure
Use this key to adjust the image density of the image to
be printed during the Auto or Manual Exposure mode.
The Darker key supports darker image density and the
Lighter key supports lighter image density.
Adjustment Keys:
8. Exposure Mode
Key:
Press to select between the Auto or Manual Exposure
mode.
9. Exposure Display: Indicates the current density level of the printed image.
10. Exposure Mode
Indicator:
Auto Exposure mode is indicated when the green Auto
light is on. The green Auto light turns off when the Scan-
ner is in the Manual Exposure mode.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
11. Multi-Print Display: Shows the number of prints set to be made. Also dis-
plays corresponding codes in the event of a malfunction
or paper misfeed. The blinking number in this display
indicates the Scanner in operation.
Display
L2
Contents
Unit
Projection Lamp malfunction
Scan Unit Drive malfunction
Scan Mirror Drive malfunction
Shading Correction malfunction
Cooling Fan Motor malfunction
Fusing malfunction
Scanner
C1
C2
C3
C4
C6
Printer
C7
Laser Diode malfunction
Polygon Motor malfunction
Main Motor malfunction
Cooling Fan Motor malfunction
Communication Error
C8
C9
CA
Cb
Scanner
Printer
CL
PE
P0
P1
Printer Clock malfunction
Paper Empty
Scanner
Printer
Paper Size Error
Paper Misfeed
(Paper Take-up Section)
P2
P3
E1
E2
Paper Misfeed
(Paper Transport Section)
Paper Misfeed
(Fusing Section)
Printer Power OFF or Cable
disconnect
Top Cover Open
12. Add Toner Indicator: Blinks when the Imaging Cartridge or Toner Cartridge
of the Printer is running out of toner and lights up when
the cartridge has completely run out of toner.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
13. Memory Input Key: To store one of the following functions into the memory
of the Scanner, first set one of the functions on Control
Panel and then press this button with the head of a pen
or other device. The next time the scanner is turned
ON, that function will appear as a default setting until a
new one is entered. (Maximum three kind of setting can
be memorized.)
1) Film Type
2) Print mode
3) Output Selection
4) Print image density
5) Exposure mode
6) Centering or Fit
7) Masking
8) Auto Skew Correction
9) Horizontal Area setting
10) Vertical Area setting
11) Electrical Zoom
12) Resolution
If you do not press the pinhole for at least 60 seconds
after a setting has been made with the Auto Reset func-
tion set to ON, the previous setting remains valid.
14. Clear/Stop Key:
15. Multi-Print Keys:
Press to clear the setting on the Multi-Print Display, re-
setting it to “1” or to stop a multi-print cycle.
This key is used to set the number of prints when print-
ing continuous, multiple pages.
The value of this setting increases by one (1, 2, 3...)
with every push of the key. (Maximum 19)
* PR mode only.
16. Start Key:
Press to make a print (scan) of the image shown on the
Screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.10.2 Control Panel (Shift Function)
Output
Selection
Tray
Cassette1
Cassette2 Auto Skew
Correction
Centering/Fit
1
Auto
Masking
Manual
Text
Print Mode
Fine
2
3
Photo
Resolution
Auto
Nega
Film Type
Posi
Job Recall
Darker
Zoom +
Auto
4
Zoom clr
Lighter
Zoom -
C
5
6
PC/PR
Shift
Start
33
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
1. Lamp Illuminance Key:
When this key is pressed together with the Shift
Key, the illumination of the screen is adjusted.
When this key is continuously pressed, the screen
is gradually darkened until it is turned OFF. When
any key is pressed then, the illumination returns to
the maximum level.
2. Resolution Key:
When this key is pressed together with the Shift
Key, the resolution of the Scanner is set.
When the Scanner is connected to the Printer: 4H
and 6H
When the Scanner is connected to the PC: 2H, 3H,
4H, 6H and 8H
* 4H represents 400dpi and 6H represents 600dpi.
3. Job Recall Key:
4. Zoom Key:
When this key is pressed together with the Shift
Key, the program registration locations (1J, 2J and
3J) are called. Each time this key is pressed while
the Shift Key is held down, the display is switched
in order of 1J → 2J → 3J.
When this key is pressed together with the Shift
Key, the electrical zoom magnification is set.
Zoom+:
When this key is pressed together with
the Shift Key, the magnification is
increased by an increment of 0.01X
(up to 2.00X).
Zoom clr: When this key is held down together
with the Shift Key for one second, the
standard magnification is resumed.
Zoom-:
When this key is pressed together with
the Shift Key, the magnification is
decreased by a decrement of 0.01X
(down to 0.50X).
5. Shift Key:
Executes an expansion function when being
pressed together with the intended function key.
6. PC/PR Key:
When this key is pressed together with the Shift
Key, the connection to the PC or to the Printer is
selected.
*This key is not valid unless the PC interface kit
(optional) is installed.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
3.11 Image Processing
Screen Image → Print Image
Explanation
Auto Masking
The system masks the black bands that run
along the edges of the image.
Trimming
The system masks everything but the center of
the image.
The Manual Frame Masking Kit (option) is
required.
Masking
The system masks the center of the image
appearing on the screen through the Manual
Frame Masking Panel function.
The Manual Frame Masking Kit (option) is
required.
Centering
The system generates an image that is
centered on the printed page, from an image
on the screen with a masked frame.
Fit
Fit the image on the Screen onto the entire
surface of the print.
Auto Skew Correction
The machine automatically correct any skew of
the image when printed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
3
Screen Image → Print Image
Explanation
Auto Format Print
The machine automatically determines the
format (portrait or landscape) of the image on
the Screen and prints it as necessary.
Electrical Zoom
The system magnifies the screen image
according to the size of paper being used. The
range of standard magnification is 1.41X for
A3, 1.55X for Ledger, 1.27X for Legal and
1.22X for B4 sized paper.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4
Mechanical and Electrical
4.1
Illumination Mechanism
4.1.1 Overview
The Illumination Mechanism efficiently uses the light produced by the
Projection Lamp to supply the most suitable amount of light for the
projection of the Microfilm. This amount of light is determined by the size
of the Microfilm and by the magnification ratio of the Lens selected for use.
4.1.2 Projection Lamp (LA1)
A DC20V, 150W halogen Lamp is used as the light source for the reader
and printer functions.
The Projection Lamp is integrated with a Lamp Reflector which is a
polygon mirror to ensure even illuminance.
NOTE
1. Whenever the Projection Lamp Unit is removed, Make sure that the
Power Switch is turned OFF.
2. Never touch the Projection Lamp immediately after it is turned OFF:
be careful, it is extremely hot.
3. Do not touch with hand or dirty with grease the surfaces of the
Projection Lamp and Lamp Reflector.
Projection Lamp (LA1)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.1.3 Projection Lamp Voltage Control Circuit
The intensity of the light emitted by the Projection Lamp is adjusted to a
level optimum for the image density by controlling the voltage applied to
the Projection Lamp.
The exposure data optimum for film image density is determined through
auto exposure data sampling made during prescan.
This exposure data is output as a Projection Lamp clock from the Main
Control Board (PWB-BB) to the Projection Lamp Regulator (PU2).
The ON and OFF periods of the Projection Lamp clock extending 606
µsec. are varied to control the Lamp voltage. The longer the OFF time, the
higher the Lamp voltage.
Projection Lamp clock
ON
OFF
H
L
606 µsec.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.1.4 Thermostat (TS1)
To avoid any of the troubles accompanying an excessive rise in the
temperature inside the machine caused by a failure of the Cooling Fan to
dissipate heat produced by the Projection Lamp, there is a Thermostat
installed at the back of the Projection Lamp.
When the ambient temperature of the Projection Lamp exceeds 122°C the
Heat-Sensitive Plate expands pushing up the Pusher Pin, which in turn
cuts off the current to the Projection Lamp Circuit.
The Circuit is reset by pushing the Reset Pin.
Thermostat
Reset Pin
Pin
Bi-metal
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.1.5 Condenser Lens
Overview
G
Not only must the amount of light projected onto the Screen or CCD
remain even despite changes in the microfilm or magnification ratio, but
also the light coming from the Projection Lamp must be efficiently
condensed. To accomplish this, the machine is equipped with two
Movable Condenser Lens: one convex and one concave.
G
Movable Condenser Lenses
The Brightness Shift Lever is moved manually according to the
magnification of the Projection Lens being used so that the Movable
Condenser Lenses are moved to the set position. The set position is color-
coded, TYPE 1 to 3, each defined by a corresponding magnification of the
Projection Lens.
TYPE
Lens Magnification
7.5X
Color Code
Blue
TYPE1
TYPE1
TYPE2
TYPE3
9X-16X
Blue
13X-27X
Green
Yellow
23X-50X
G
Condenser Mirror
Light from the Projection Lamp after having passed through the Movable
Condenser Lenses strikes this Mirror and is reflected onto the Fresnel
Lens.
G
Fresnel Lens
The Fresnel Lens, which is an acrylic plate with stepped setbacks,
ensures even illuminance from the Lamp.
Fresnel Lens
Movable Condenser
Lenses
Projection
Lamp
Condenser Mirror
Brightness
Shift Lever
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.1.6 Projection Lens
The Projection Lens enlarges the image of the Microfilm and projects it
onto the Screen or CCD.
Each Projection Lens comes in a unit. The Focus Ring and Zoom Ring of
the Unit are used to bring the image on the Screen into focus and enlarge
or reduce it, respectively.
The Prism Lens for image rotation is installed in the Prism Holder fixed to
the machine.
The Projection Lens Unit is slid into position in the Lens Holder of the
machine. To insert the Unit, raise the Prism Holder and, at the same time,
push it into position.
When a Projection Lens Unit is installed, the Brightness Shift Lever must
be moved as required according to each magnification.
Prism Unit
Prism Holder
Zoom Ring
Lens Holder
Focus Ring
Projection Lens Unit
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.2
Image Rotation
The Prism Unit is rotated to correct any tilt of the image microfilm projected
on the Screen.
4.2.1 Prism Rotation
The Auto Image Rotating Knob is linked to the Auto Image Rotating
Variable Resistor (VR1). Turning the Knob clockwise or counterclockwise
turns the Auto Image Rotating Motor (M5) whose drive is transmitted via
a belt to the Prism Gear, thus turning the Prism Unit.
Belt
Auto Image Rotating
Variable Resistor (VR1)
Pulley
Auto Image
Rotating Motor
(M5)
Auto Image
Rotating Knob
Prism Unit
Prism Gear
4.2.2 Auto Image Rotating Motor (M5) Control Circuit
When the Auto Image Rotating Knob is at the home position (center),
voltage at PJ2C-2 is set at DC2.5V and the Auto Image Rotating Motor
(M5) remains stationary.
PJ2C-2 reads fluctuations of the input voltages as the Auto Image
Rotating Knob is turned, there by determining the direction of rotation of
the Auto Image Rotating Motor.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.3
Optical Section
4.3.1 Overview
The basic function of the Optical Section is to project an enlargement of
the image on the microfilm onto the Screen when in the Reader Mode and
onto the CCD when in the Scan Mode.
There is a unique light path formed in each of these modes.
The light path formed in the Reader Mode is called the Reader Path and
that formed in the Scan Mode is called the Scan Path.
Each light path is formed by two Reader Path Mirrors and three Scan path
Mirrors.
1st Reader Path Mirror
2nd Reader Path Mirror
2nd Scan Path Mirror
Reader
Path
Scan Path
1st Scan Path
Mirror
CCD
Projection Lamp
3rd Scan Path Mirror
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.3.2 Reader Path
The Reader Path is established when the Power Switch is turned ON and
remains formed except during a scan movement.
The image on the microfilm is projected onto the entire area of the Screen
by means of the two Reader Path Mirrors.
The light path between the Projection Lamp and Screen measures
1,293mm.
4.3.3 Scan Path
When in the Scan mode, the 1st Scan Path Mirror moves to a position that
will block the Reader Path.
It then turns to direct the film image through the four Scan Path Mirrors
onto the CCD so that it can read the image data in the sub-scanning
direction.
The light path between the Projection Lamp and CCD measures
1,298mm.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.3.4 Scan Table Drive Mechanism
The Reader Path is switched from the Printer Path, or vice versa, by
moving the Scan Table to the respective positions.
The Scan Table is driven from the Scan Table Drive Motor (M2). The
direction and speed of rotation of the Scan Table Drive Motor (M2) are
controlled by the outputs from pins 3, 4, 5 and 6 (øA, øB, øA, and øB) of
PJ5T on the Motor Drive Board (PWB-T).
Reader Position
Reader Position
Sensor (PC3)
Scan Table Drive
Motor (M2)
Scan Position
Scan Position
Sensor (PC4)
To switch from the Reader Path to the Printer Path, the Scan Table Drive
Motor M3 is energized there by moving the Scan Table toward the Printer
Position.
The Scan Table at the Reader Position is detected by the Reader Position
Sensor (PC3) and that at the Printer Position is detected by the Scan
Position Sensor (PC4).
It takes less than 1.3 sec. for the Scan Table to move from the Reader to
Printer Position.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.3.5 Scan Mirror Motion Control
The motion of the Scan Mirror is controlled by the Scan Lever and Shaft
as the Shaft is driven by the Scanning Motor (M1).
The Scan Mirror scans the image of the microfilm at a speed 1/631.6 of
the Scanning Motor (M1).
Once the prescan motion is initiated, the leading edge of the image is
synchronized with that of the paper, and the completion of the scan motion
is detected, by the Scan Start Position Sensor (PC1) which are activated
and deactivated by the cutouts in the light blocking Lever.
Scan Mirror first makes a prescan motion for reading the data before
making the scan motion.
Light blocking Lever
Scan Mirror Position
Sensor (PC2)
Scanning Motor (M1)
Image Leading-Edge
Position Sensor (PC1)
Scan Mirror
Shaft
Scan Lever
: Prescan
: Scan
The Image Leading-Edge Position Sensor (PC1) and Scan Mirror Position
Sensor (PC2) detect the cutouts in the light blocking lever.
The starting position for the prescan or scan motion is determined by
particular states of these sensors, blocked (activated) or unblocked
(deactivated), as detailed below.
Scan Motion
Prescan
Scan
PC1
PC2
ON (blocked)
ON (blocked)
OFF (unblocked)
ON (blocked)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.3.6 Mirror Scan Motor (M1) Control Circuit
Drive of the Scanning Motor (M1) is controlled by the signals which are
input to the Motor Driver Board (PWB-T) from the Main Control Board
(PWB-BB).
These signals determine the direction (forward or backward) and speed of
rotation of the Scanning Motor when the Scan Mirror makes a prescan
and scan motion.
These signals cause the Scanning Motor drive pulses to be output from
the pins (A, B, A, B) of the Motor Driver Board (PWB-T), which turns the
Scanning Motor (M1).
Motor
Step
A
L
B
H
L
A
H
H
H
L
B
H
H
H
H
H
L
1
2
3
4
5
6
7
8
A
A
L
N S
S N
H
H
H
H
H
L
L
DC24V
L
H
H
H
H
L
B
L
B
H
H
L
DC24V
L
Motor
Step
Speed (Full Size)
82.5mm/sec.
110mm/sec.
Scan(800dpi)
Scan(600dpi)
Scan(400dpi)
Scan(300dpi)
Scan(200dpi)
Prescan
1→2→3→4→→5→6→7→8→1→.....
1→2→3→4→→5→6→7→8→1→.....
1→2→3→4→→5→6→7→8→1→.....
1→2→3→4→→5→6→7→8→1→.....
2→4→6→8→2→.....
165 mm/sec.
220 mm/sec.
330 mm/sec.
330 mm/sec.
8→6→4→2→8→.....
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.4
CCD Section
There are five 960-pixel CCD sensor chips arranged in a zigzag as
illustrated below.
The total number or pixels that can be read is 4,800 with a resolution of
400dpi.
Reading With: 304.8 mm or more
Pixel Size: 63.5 µm x 63.5 µm
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.5
Image Bus
The image data read by the CCD goes through analog-to-digital
conversion before being output.
CCD
The CCD (Charge Coupled Device) reads the data
on the Film.
PWB-A
PWB-BB
The elemental output signals are evened out in
compensation for uneven illuminance of the
Projection Lamp and sensitivity variations among
CCD cells and Projection Lens.
Shading correction
Shading Correction
If the CCD were to read the reflected light from an
original having a uniform density, the outputs along
the length of that CCD may vary individually due to
uneven light distribution along the length of the
Lamp and varying sensitivities of different CCD
chips. These variations are corrected through
shading correction.
White Black
Image
White
CCD output
Black
White
After Shading Correction
Black
The analog image signals output from the CCD are
converted to digital image signals.
A/D conversion
Line memory
The pixel signals from the five CCD chips are
output serially in the order of CCD1, CCD2, CCD3,
CCD4, and CCD5.
The data read by the CCD is proportionate to the
intensity of the light that has passed through the
film. A conversion formula is used to convert the
data read by the CCD into the image density data
which has a characteristic linear to the film density.
Density conversion
A
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
A
Converts the output resolution
(from 400 dpi to 800, 600, 300 or 200 dpi).
Resolution conversion
Enlargement or reduction in the main scanning
direction.
MagnificationChange
in main scanning
direction
Centers the image data by shifting it in the main
scanning direction.
Centering in main
scanning direction
Edge emphasis and smoothing are carried out.
MTF correction
• Edge Emphasis (Text Image)
The outlines of characters and fine lines are made
sharper as they appear on the copy by correcting the
MTF (modulation transfer function) characteristics
(resolution).
*MTF: Modulation Transfer Function
• Smoothing (Photo Image)
Image noise contained in the solid area of the image
is reduced to smooth the image, thereby improving
image quality of photos.
Contrast fine-adjustment
(γ : Density reproduction curve)
Linear γ conversion
Enhances reproduction of characters and fine lines
that are low in contrast.
Nonlinear conversion
Conversion into binary
Converts 8-bit image data into
binary image data by comparing
to a certain threshold.
PWB-BB
Grayscale Image
Binary Image
B
C
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
B
Grayscale Image
C
Binary Image
PWB-BB
PWB-EE
Frame Masking
Erases the frame to prevent
the areas outside the image
from being output.
Serial-to-parallel
conversion
Image rotated 90°
Serial-to-parallel conversion
Converts pixel-by-pixel
serial image data into a
corresponding set of
parallel data for 8 pixels.
The image data is rotated by
90 degrees and converts
pixel-by-pixel serial image
data into a corresponding set
of parallel data for 8 pixels.
PWB-J
Image memory (option)
Image memory (standard)
Binary: Stores every 8 pixel temporarily.
Grayscale: Stores every 1 pixel temporarily.
Parallel-to-serial
conversion
Converts parallel data for 8
PWB-SS
pixels into a corresponding set
of pixel-by-pixel serial image
data.
SCSI I/F
Printer I/F
Transfers parallel image data
for 8 pixels to the Printer.
Transfers parallel image data for
8 pixels to the host computer.
Printer
Host Computer (PC)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.6
Auto Masking
4.6.1 Overview
If a print is made from an image that is projected smaller than the Markers
on the screen, the non-image areas of the film result in black bands
running around the image on the print.
The Auto Masking Function Automatically detects the non-image areas of
the film.
4.6.2 Masking Area Detection
The CCD Board (PWB-A) is detects the density of the film image.
If Auto Masking is selected on the control panel, the CCD Board (PWB-A)
detects the masking area (By measuring the intensity of light) while the
Scan Mirror makes a prescan motion.
4.6.3 Requirements for Auto Masking
G
Film Requirements
Negative
Positive
Film Base Density
0.2 or less
0.8 or more
0.2 or more
Background Density
0.8 or more
Main Scanning Direction
(CCD)
Feed Direction
(scanning direction)
Screen
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
G
Effective Image and Effective Frame
Screen
45mm or more
10mm or more
10mm or more
45mm or more
Effective Image Width: The image is considered as an image if it extends
45 mm or more .
Effective Frame Width: The frame is considered as a frame if it extends 10
mm or more.
* The effective image width in the vertical and horizontal direction must be
45 mm or more.
G
Memorandum Image Masking
Screen
A
17mm or more
X
L
Image Width : X + L
Memorandum Image width: X= 12mm or more
Memorandum Image length: 17mm or more
X ≤ L-17mm : Detected as a Blip
L-17mm < X ≤ L+17mm: Unfixed
L+17mm ≤ X: Detected as a Blip
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
G
Memo image away from the frame (A Island blip)
An island blip (a blip that positions away from the image) is not masked; it
is considered as a normal.
Screen
A
10mm or more
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.7
Auto Image Skew Correction
4.7.1 Overview
The CCD Board (PWB-A) detects the image which skew on the screen
and corrects automatically at the time of scan.
Corrects of the straight image by rotating the prism unit by the auto image
rotation motor (M5).
4.7.2 Requirements for Auto Skew Correction
10mm or more 10mm or more
10mm or more
100mm
or more
less than 30°
10mm or more
45mm or more
Image slant:
Image Size:
less than 30°
100mm x 45mm or more
Frame of Image: 10mm or more
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.8
Manual Frame Masking
The machine makes a print of the area of image on the Screen defined
with the Manual Masking Panels.
The print area is defined independently in the vertical direction and
horizontal direction. If none is specified, the machine makes a normal
print.
There are 42 LEDs/switches laid out both in the horizontal as well as
vertical direction. Two Clear Buttons are placed; one at the bottom of the
vertical row of LEDs/switches and the other on the left end of the
horizontal row of LEDs/switches.
Screen
LED/switches
Clear Button
LED/switches
The machine makes a print of only the image area defined with the
LED/Switches.
Paper
A B C D
F G
J K
E F GH
I J KL
MN O P
Print Area
Print Area
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.9
2 to 1 Printing Function
4.9.1 Overview
As shown above, two scanners, each equipped with the 2-to-1 Printing
Function, can be connected to a single printer which manages the print
jobs sent from both scanners.
Each scanner can be set to print marks (I or II) in the top left-hand
corner of the page, enabling easy identification of each scanner’s print job.
Scanner
Printer
4.9.2 Operation
When printing, the scanner occupies the printer. When the print is ended,
the scanner opens the printer.
The scanning begins when the start key to the other scanner is pushed.
And waited that the printer is opened while storing the image in the
memory in the scanner while printing.
Meanwhile, scanner is shown for the Multi-print display to blink, and not to
accept the next scanning.
If the print of the preceding other scanner ends, and the printer is opened,
the image stored in the memory as here occupies the printer is printed.
A job that is waiting to be printed can be cancelled by pressing the Clear/
Stop key on the scanner that sent the job.
(Push the Clear/Stop Key three times when you used the print reserve
function)
As a result, the print job is deleted from the memory and that scanner's
Multi-print Display stops blinking and stays lit.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical and Electrical
4
4.9.3 Identification Marks
In order to distinguish which scanner sent a print job, the scanners are
equipped with an identification Mark Printing Function which has the
following settings:
Function Mode
Setting Identification Mark
S7
d0
d1
d2
no mark
S7-d1: Prints pattern 1 (!)
S7-d2: Prints pattern 2 (!!)
Identification Mark
Print Direction
Printed Image
The printable area is reduced by 3 mm on the left side and the 1.5-mm-
wide identification mark is printed in the top corner of the page at a
distance of 1.5 mm to the left of the image.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5
Disassembly and Cleaning
5.1
Precautions
5.1.1 Precautions for Disassembly and Cleaning
1. Before disassembling, always make sure the Power Plug is
unplugged.
2. Use only fuses of the indicated rating.
3. Except specified occasion, re-assembly have to be carried out by
reversing the disassembly procedure.
4. If it is necessary to plug in the Power Cord and operate the machine
after disassembling it, please be careful of the following:
- Keep your hands, clothing, etc. well away from operating or
rotating parts (such as belts, rollers, fan motors, etc.).
- Never touch the terminals of electrical parts or high-voltage parts
(such as chargers and the high-voltage unit).
5. When the machine is stopped, the Projection Lamp is hot, so handle it
very carefully.
6. To prevent damage to ICs from static electricity, do not touch the ICs
on the PWB or the terminals of peripheral electricity parts with your
hands.
7. Always unplug connectors by holding the connector housing. Pulling
on the connectors on the PWBs themselves, always make sure the
Power Cord is unplugged first.
8. Do not disassemble the Right and Left Frame Covers and the fixing
screws to which red paint has been applied.
Right Frame Cover
Left Frame Cover
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.2
Handling of P.W.Boards
5.2.1 Precautions regarding transportation and storage
1. During shipment or when in storage, new P.W.Board must not be
indiscriminately removed from their protective bags.
2. Do not store or place these P.W.Boards in a location exposed to direct
sunlight or in a location where they will be exposed to high
temperatures.
3. After removal from a machine, P.W.Board must be placed in their
respective conductive bag or wrapped in aluminum foil without fail.
Never wrap them in plastic, paper or any other material.
4. When removal from the conductive bag or case becomes absolutely
necessary, always place the Board removed on its conductive mat in
an area as free as possible from static electricity.
5. Do not touch the terminals of the ICs with your bare hands.
5.2.2 Precautions when replacing PWBs
1. Any Board should be replaced as an Assy.
2. When taking any Board out of its conductive bag or conductive case,
do not touch the terminals of the ICs or the printed pattern. Place it in
position by holding only the edge of the Board.
3. Connect the connectors to or disconnect them from any Board only
after having unplugged the Main Power Cord of the machine.
5.2.3 Precautions when checking PWBs
1. Avoid checking PWBs with testers; instead, use operating parts of the
machine, indicator lamps, and other means to evaluate operational
conditions.
2. Never permit shorts between IC terminals due to metal fittings, etc.
3. If it is necessary to touch elements on the PWB with your hand, make
sure your body is properly grounded.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.3
Maintenance and Inspection
5.3.1 Preventive Maintenance Schedule List
Parts
Cleaning Cycle
Replacement Cycle Refer to
Reader and Scan Path Mirrors
When image
trouble occurs
-------
page 67
Friction Plate
Bushing
-------
-------
-------
300,000 scans
page 73
page 73
page 65
300,000 scans
Projection Lamp
When “L2” displays
*Replacement cycle is the number of times of scan.
5.3.2 Details of readjustments needed when parts are replaced
Replacement of the following parts calls for rechecking, readjustments, or
resetting of certain items.
Follow the corresponding procedure given below whenever they have
been replaced.
Name
Readjustments /Resetting/Rechecking
PWB-A
1. Shading Correction “b6”
2. Auto Exposure Coarse Adjustment
PWB-BB
1. Shading Correction “b6”
2. Scan Speed Adjustment
Turn off all DIP switches (DSW1) on the new board.
Make the function mode setting (S,y,o) on the new board.
(“About the Function Mode Setting Label” on page 82)
PWB-SS
PU2
Make the same SCSI ID setting for Rotary Switch (RSW1) on the new
board as those of the old board.
Projection Lamp Voltage Adjustment “F7”
Refer to “Function Mode and Adjustment” on page 77 for the adjustment procedure.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4
Disassembly and Cleaning Procedure
5.4.1 Removal of the Outer Covers
Remove the two screws and then
1
slide the Optical Cover to the rear
side of the machine.
Then holding up the rear side of
the Optical Cover and remove it.
NOTE:
Mirror is fitted to the back side of
the Optical Cover. Using care
not to touch or damage this mir-
ror, place the Optical Cover
upside down.
Mirror
Holding up and remove the
2
Screen Frame and then
disconnect the connector of the
Control Panel Board.
Remove the stopper from the
3
Right Cover and then open the
Right Cover.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Only 220-240V area:
Remove the metal plate in the
Left Cover also.
Remove the Left Cover.
(1 screw)
4
Only 220-240V area:
Remove the metal plate in the
Right Cover also.
Remove the Projection Unit.
5
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Remove the Lower Left Cover.
(2 screws)
6
7
Remove the Lower Right Cover.
(2 screws)
Remove the Rear Cover.
(4 screws)
8
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.2 Replacing of the Projection Lamp
Slide the Projection Lamp Unit out.
1
2
Remove the Projection Lamp from
the Lamp Holder.
NOTE
➜
Do not touch with bare hand and extremely hot Projection Lamp
immediately after the machine has been turned OFF.
Remove the Projection Lamp from
the Lamp Socket.
3
Insert a new Projection Lamp so
that the mark on its base is facing
upwards. Make sure that the new
Projection Lamp is inserted
securely so that there is no gap
between the projection Lamp and
the Lamp Socket.
4
Mark
NOTE:
➜
Do not touch the reflector mirror surface of the Projection Lamp.
➜
Fingerprints, smudges or debris should be wiped clean with a soft, dry
cloth.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Insert the new Projection Lamp all
the way into the Lamp Holder.
5
6
Slide the Projection Unit back into
the machine.
5.4.3 Cleaning of the Projection Lamp
Wipe all foreign matter off the
1
surface of the Projection Lamp
with a soft piece of cloth which
has been dampened with alcohol.
5.4.4 Cleaning of the Condenser Lens and Mirrors
Remove the Projection Unit.
1
2
Dust off the surface of the
Condenser Mirror by using a
blower brush or a piece of soft
cloth.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.5 Cleaning of the each Mirrors
Remove the Optical Cover.
1
2
Wipe clean the 1st Reader Path
Mirror with a soft piece of cloth.
Wipe clean the 2nd Reader Path
Mirror with a soft piece of cloth.
3
4
Remove the Left Cover. (1 screw)
Only 220-240V area:
Remove the metal plate in the
Left Cover also.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Wipe clean the 2nd and 3rd Scan
Path Mirror with a soft piece of
cloth.
5
5.4.6 Cleaning of the CCD Filter
Remove the Left Cover.
(1 screw)
1
Only 220-240V area:
Remove the metal plate in the Left
Cover also.
Dust off the surface of the CCD
2
Filter by using a blower brush or a
piece of soft cloth.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.7 Removal of the CCD Assy
Remove the stopper from the
Right Cover and then open the
Right Cover. (2 Screws)
1
Only 220-240V area:
Remove the metal plate in the
Left Cover also.
Remove the Left Cover.
(1 screw)
2
Only 220-240V area:
Remove the metal plate in the
Left Cover also.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Remove the CCD Assy Lower
Plate.
(2 screws)
3
4
Remove the CCD Assy.
(two shoulder screws, Three
connectors)
Unplug connector from the CCD
Assy.
5
6
Remove the CCD Assy Cover.
(loosen the four screws)
NOTE:
After the CCD Assy has been
mounted, make the shading cor-
rection (b6) by following the pro-
cedure given on page 104.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.8 Removal of the Power Unit
Remove the Optical Cover.
(2 screws)
1
Disconnect the five Connectors of
the Power Unit from the machine.
2
NOTE:
For 220-240V area, disconnect
the 2P connector of the Coil
also.
Coil
Remove three screws and then
remove the Power Unit from the
machine.(3 screws)
3
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.9 Removal of the P.W.Boards.
Remove the Left Cover,Lower Left Cover and Rear Cover.
(Refer to "Removal of Outer Cover".)
1
2
Open the Right Cover.
Only 220-240V area:
Remove the metal plates in the
Left and Right Cover also.
Remove the CCD Assy Lower
Cover. (2 screws)
3
Remove the front and rear Shield
Plate. (loosen the four screws)
4
Unplug all connectors on the
P.W.Board.
5
6
PWB-BB
Remove the screws and then
remove the each P.W.Board.
PWB-EE
-PWB-BB (5 screws)
-PWB-T (4 screws)
PWB-T
-PWB-EE (6 screws)
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.10 Replacing Scan Motor bushing and friction plate
Remove the Optical Cover.
(2 screws)
1
Tilt the Scan Motor Assy in the
direction of the arrow and,
pressing the shaft in the direction
of the arrow, re-move the bushing
and then peel the friction plate off
the Scan Motor Assy.
2
Scan Motor
spring
NOTE:
Do not lose the pin.
friction plate
Pin
bushing
5.4.11 Replacing the Fuse of the Power Unit
Remove the Optical Cover.
(2 screws)
1
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Remove the Power Unit Cover.
(3 screws)
2
Replace the Fuse of PU1.
Main Power Unit: PU1
3
4
AC250V 12A(100/120V area)
AC250V 6.3A(220/240V area)
Replace the Fuse of PU2.
Projection Lamp Regulator: PU2
AC125V 5A(100/120V area)
AC250V 5A(220/240V area)
5.4.12 Replacing the Main Fuse
Replace with New Fuse.
1
Main Fuse:
120V area: 250V 10A
220/240V area: 250V 6.3A
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
5.4.13 Exchanging the Oscillator Chip
When using MSP2000 printer, you must exchange the Oscillator Chip
(OSC1) on Printer I/F Board (PWB-EE) of the Microfilm Scanner for the
Oscillator Chip supplied with MSP2000 Printer.
MSP2000 Printer
Remove the Projection Unit.
1
Remove the Lower Left Cover.
2
Remove the stopper from the
3
Right Cover and then open the
Right Cover.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly and Cleaning
5
Only 220-240V area:
Remove the metal plate in the
Right Cover also.
Remove the Shield Cover (front).
4
5
Remove the two Oscillator Chips
from PWB-EE.
PWB-EE
OSC2
OSC1
Install the Oscillator Chip supplied into the OSC1 socket as shown on
the illustration
6
7
PWB-EE
OSC2
OSC1
Reinstall all the covers.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6
Function Mode and Adjustment
6.1
Precautions
1. Always unplug connectors by holding the connector housing.
Pulling on the cable cord can lead to problems with poor contact.
When unplugging connectors on the PWBs themselves, always make
sure the power is OFF first.
2. If it is necessary to plug in the power cord and operate the machine
after disassembling it, please be careful of the following.
G
Keep your hands, clothing , etc. well away from operating or rotating
parts (such as gears and fan motors, etc.).
G
Never touch the terminals of electrical parts or high-voltage parts
(such as power unit.).
3. See DISASSEMBLY AND CLEANING for the procedures to replace
parts and disassemble the machine.
4. Before starting the adjustment procedures, always make sure that the
power cord has been unplugged.
6.2
Overview
The function mode which performs setting and adjustment of the machine
is constituted as follows.
Display
Function Mode
S mode
Contents
Machine Function Setting Mode 1
y mode
Machine Function Setting Mode 2
o mode
F mode
b mode
Machine Function Setting Mode 3
Machine Operation Check Function 1
Machine Operation Check Function 2
* mark in column of "setting" expresses an in default setting.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.3
Function Mode List
6.3.1 S mode (Setting Function 1)
No.
S1
Function
Setting Contents
Auto Reset
*d0
d1
ON (60 sec.)
OFF
S2
S3
S4
Auto Power Save
*d0
d1
d2
Disable
Enable (30 minute)
Enable (60 minute)
Auto Projection Lamp OFF
Coin Vender & Foot Switch
*d0
d1
d2
Disable
Enable (30 minute)
Enable (60 minute)
*d0
d1
d2
d3
Disable
Enable (Coin Vender)
Enable (Coin Vender)
Enable (Foot Switch)
S5
S6
S7
Fine Mode
*d0
d1
Mode 1: Contrast Emphasis
Mode 2: Outline Emphasis
Paper Tray Feed Size
(MSP3000 Printer)
*d0
d1
Crosswise
Lengthwise
Machine ID Printing
*d0
d1
d2
None
Pattern 1
Pattern 2
S8
S9
Cycle Print Mode
*d0
d1
Disable
Enable
Contrast Adjustment (N-P)
d1
|
Lower
|
*d8
|
dF
Center
|
Higher
SA
Contrast Adjustment (P-P)
d1
|
Lower
|
*d8
|
Center
|
dF
Higher
Sb
Scan Table Stop Position
Adjustment (Scan Position)
d0
|
toward the rear
|
dF
toward the screen
SC
Scan Table Stop Position
Adjustment (Reader Position)
d0
|
toward the screen
|
dF
toward the rear
Sd
SE
Auto Image Rotation 90 degree rotation
Function
*d0
d1
Disable
Enable
The print function at the time of Toner
Empty detection
*d0
d1
print is impossible.
print is possible.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.3.2 y mode (Setting Function 2)
No.
y1
Function
Not Used
Setting Contents
*d0
y2
Auto Paper Source Switching
*d0
d1
Auto Switching
Disabling Auto Switching
y3
Auto Film Format Select Print
d0
d1
Disable
Enable
y4
y5
Not Used
*d0
Memo Image Masking
*d0
d1
OFF
ON
y6
y7
Prescan Operation
*d0
d1
2 times
1 time
Auto Skew Correction Retain
*d0
d1
Retain
Not Retain
y8
y9
yA
yb
Not Used
*d0
*d0
*d0
Not Used
Not Used
Magnification Warning Display
d0
*d1
Not Display
Display
yC
Print Reserve Function
d0
*d1
Not Accepts
Accepts
y3:default setting (d0: USA and Canada Area, d1:except USA and Canada Area)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.3.3 o mode (Setting Function 3)
No.
o1
Function
Setting Contents
Metric/Inch Setting
d0
d1
Metric
Inch
o2
o3
o4
o5
o6
o7
o8
N-P Auto Exposure Coarse
Adjustment
d4
|
dC
Lighter
|
Darker
P-P Auto Exposure Coarse
Adjustment
d4
|
dC
Lighter
|
Darker
Scan Speed Adjustment
d5
|
db
Lager
|
Smaller
Adjustment of the image area
Lengthwise Position
d5
|
db
Shift to a Top
|
Shift to Bottom
Adjustment of the Right and Left
Frame Black Band Width
d5
|
db
band width decreases
|
band width increases
Adjustment of the Top and Bottom
Frame Black Band Width
d5
|
db
band width decreases
|
band width increases
Projection lamp burn out detection
(L2) setting
*d0
d1
Detects
Not Detects
o9
Not Used
*d0
oA
Host Driver
*d0
d1
MS 6000
MS 2000
d2
MicroDAX (Fixed Window)
ob
Vender Name/Model Name
*d0
d1
d2
Minolta MS 6000
Minolta MS 2000
OEM Name
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.3.4 F mode (machine operation checks)
No.
F1
F2
F3
F4
Function
Contents
ROM Version Check
Total Scan Counter
Total Print Counter
Counter Clear
Displays the present ROM version.
Displays the number of times of total scan.
Displays total print number of sheets.
Clears the number of times of total scan,
and print number of sheets.
F5
LED Check
(Control Panel)
Lights up all the LEDs on the Control Panel
for 2 sec.
F6
F7
for Factory use
Do not use in field.
Projection Lamp Voltage
Adjustment
Makes adjustment of the Projection Lamp
(LA1) reference voltage.
F8
Reset the Setting Data
Function mode setting value and job
program are reset to the default value.
6.3.5 b mode (machine operation checks)
No.
b1
Function
Contents
Scan Table Unit drive check
Moves the Scan Table into reader and
scan position.
b2
Scan Mirror operation check
Moves the Scan Mirror into reader and
scan position.
b3
b4
for Factory use
Do not use in field.
Prism Rotation drive check
Checks an operation of Auto Image
Rotation Motor.
b5
Single Scan function check
Turn the machine in the single scan
operation.
b6
b7
b8
Shading Correction
Test Print
Performs the Shading Correction.
Performs the Test Print of the Printer.
Do not use in field.
for Factory use
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.3.6 About the Function Mode Setting Label
Remove the Top Cover by using a Slotted Screwdriver.
[FUNCTION MODE SETTING] Label is attached on the back of the Top
cover.
When Main Control Board (PWB-BB) is exchanged, it inputs the setting
value of "FACTORY" column on the label into each Function Mode.
Moreover, when setting value is changed in field, it writes setting value to
the "FIELD" column.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.4
Operation of the Function Mode
6.4.1 Entering the Function Mode
1. Press the Exposure Mode
Select Key, Multi-Print Key and
Clear/Stop Key on the control
panel at the same time for two
seconds or more.
The Multi-Print Display will show
"S".
2. Press the Multi-Print Key to
select the function mode.
Each depression of this key
changes the mode into the
following.
S→y→o→F→b→S→y....
S: Setting Function 1
y: Setting Function 2
o: Setting Function 3
F: Machine Operation Check Function 1
b: Machine Operation Check Function 2
*c4: for factory use (do not entry)
3. Press the Exposure Adjustment
Key to select the function number.
select
select
S1→S2→...→S1→
y1→y2→...→y1→
o1→o2→...→o1→
F1→F2→...→F1→
b1→b2→...→b1→
6.4.2 Execution method in F and b mode (except F4, F8 and b6)
1. To perform the function, press the
Start key.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.4.3 Execution method in F and b mode (F4, F8 and b6)
1. To perform the function, press the
Mode Memory key.
Mode Memory Key
6.4.4 Execution method in S, y and o mode
1. Press the Exposure Mode Select
Key.
2. The present setting value is
displayed on the display window.
3. Press the Exposure Adjustment
Key to select the setting number.
select
select
d0→d1→............→d7→d8
4. Press the Start Key to update the
setting value.
6.4.5 Leaving the Function Mode
1. Press the Exposure Mode Select
Key, Multi-Print Key and Clear/
Stop Key on the Control Panel at
a time.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.5
S mode Operations
6.5.1 S1: Auto Reset
Setting changes made to the control panel that are not used within 60
seconds of being input are automatically cancelled and the system reverts
back to the original settings.
Display
S1
setting
Function
*d0
d1
Enable (60 seconds)
Disable
6.5.2 S2: Auto Power Save
Turns the Printer's fuser OFF if the system is left idle for a specific period
of time.
* 200V units operate on a default 30 minute Auto Power Save setting.
Display
S2
setting
Function
*d0
d1
Disable
Enable (30 minute after)
d2
Enable (60 minute after)
6.5.3 S3: Auto Projection Lamp OFF
Turns the Scanner's Projection Lamp OFF if the system is left idle for a
specified period of time.
Display
S3
setting
Function
*d0
d1
d2
Disable
Enable (30 minute after)
Enable (60 minute after)
6.5.4 S4: Coin Vender / Foot Switch Setting
When you equip this system with the coin vender (option) or Foot Switch
(option), select the d1(d2) or d3.
Display
S4
setting
Function
*d0
d1
d2
d3
Disable
Enable (Coin Vender)
Enable (Coin Vender)
Enable (Foot Switch)
*d1 and d2 are the same functions.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.5.5 S5: Fine Mode Setting
Select the function in the fine mode, when selecting Nega print mode on
the control panel.
Display
S5
setting Function
Contents
*d0
d1
Mode 1:
Contrast Emphasis
Applied when film contains text that is poorly
contrasted against its background making it
difficult to read.
Mode 2:
Outline Emphasis
Applied when film contains blurred black and
white images.
6.5.6 S6: Paper Tray feed size (MSP 3000 Printer)
Determines the desired paper size supplied by the Paper Tray of the
printer. It is possible to feed the following paper sizes and orientations into
the printer:
Inch values: Letter (Lengthwise) or Letter (Crosswise)
Metric values: A4 (Lengthwise) or A4 (Crosswise)
Display
S6
setting
Function
*d0
d1
Crosswise
Lengthwise
6.5.7 S7: Machine ID Printing
When two scanners are connected to one printer, this function leaves an
identification marker (I) on the print so that the scanner used for the job
can be determined after printing.
Display
S7
setting
Function
*d0
d1
d2
None
Pattern 1
Pattern 2
Pattern Dimension:
3mm x 3mm
Mark Position:
Right side of leading edge
Pattern 1
Pattern 2
feed direction
feed direction
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.5.8 S8: Cycle print mode
This function automatically scans the next image following a preset period
of time. Images are set by the user onto the Carrier Glass in between
cycles.
Display
S8
setting
Function
*d0
d1
Disable
Enable
6.5.9 S9: Nega Contrast Adjustment
Adjusts contrast in the negative film use.
Display
S9
setting
Contrast
d1
|
Lower
|
*d8
|
Center
|
dF
Higher
6.5.10 SA: Posi Contrast Adjustment
Adjusts contrast in the positive film use.
Display
SA
setting
Contrast
d1
|
Lower
|
*d8
|
Center
|
dF
Higher
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.5.11 Sb: Scan Table Stop Position Adjustment (Scan Position)
This adjustment is necessary when any of the following symptoms occurs.
Symptom 1.
Symptom 2.
Each time a print is made, the image on the Screen shifts vertically.
The noise becomes big that is heard when the Scan Table hits against
the Scan Table Stopper during its motion from the reader position to
printer position.
Rear
Display setting Scan Table Stop Position
Sb
d0
|
toward the rear
|
d8
|
dF
center
|
toward the screen
Screen
* The stop position of the Scan Table should be set toward the rear for
symptom 1 explained above and toward the screen for symptom 2.
6.5.12 SC: Scan Table Stop Position Adjustment (Reader Position)
This adjustment is necessary when any of the following symptoms occurs.
Symptom 1.
Symptom 2.
Each time a print is made, the image on the Screen shifts vertically.
The noise becomes big that is heard when the Scan Table hits against
the Scan Table Stopper during its motion from the reader position to
printer position.
Rear
Display setting Scan Table Stop Position
SC
d0
|
toward the screen
|
d8
|
dF
center
|
toward the rear
Screen
* The stop position of the Scan Table should be set toward the screen for
symptom 1 explained above and toward the rear for symptom 2.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.5.13 Sd: Auto image rotation 90 degree rotation function
When printing the A3 (Ledger) size or B4 (Legal) size by 600dpi, the 90
degrees electric image rotation is not possible.
Select whether to enable the 90 degrees image rotation with the prism
when A3 size (Ledger) or the B4 size (Legal) is printed with 600dpi.
The landscape screen image can be printed by effectively setting when
the prism is installed.)
Display
Sd
setting
Function
*d0
d1
Disable
Enable
6.5.14 SE: The print function at the time of Toner Empty detection
Selects the printing function in the case of detecting the Toner Empty of
the printer.
Display
SE
setting
Function
*d0
d1
print is impossible
print is possible
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.6
y mode Operations
6.6.1 y2: Auto Paper Source Switching
Allows you to specify the paper source when same size paper is loaded
into the both paper feeding tray and paper feeding cassette.
Display
y2
setting
*d0
Function
Function
Auto switching Printing continues by automatically switching to
the remaining paper source after paper in the
specified paper source runs out.
d1
Disabling
A paper empty mode occurs and printing ceases
Auto Switching after paper in the specified paper source runs
out. The paper source must be refilled or the
paper source must be switched by pressing the
Size Selection Key in order to resume printing.
6.6.2 y3: Auto Film Format Select Print
Selects the function which rotates 90 degrees and prints a screen image.
When only the landscape paper is set to the printer, the portrait screen
image can be printed on the landscape paper by this setting.
Display
y3
setting
Function
*d0
d1
Disable
Enable
6.6.3 y5: Memo Image Masking
If film with a memo image on it at the bottom of its frame is scanned with
Auto Masking enabled, the memo image is erased by Auto Masking.
In this case, setting y5 to the ON (d1) position will prevent the memo
image from being masked.
Paper
Screen
OFF
A
A
ON
A
Memo Image
Paper
Display
y5
setting
Function
*d0
d1
OFF
ON
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.6.4 y6: Prescan Operation
Select the prescan operation when using an Auto Masking and Auto Skew
correction function.
Display
y6
setting
*d0
Function
1 time
Explanation
Reading speed is quick.
d1
2 times
Although reading is late, but accuracy of
Frame Masking becomes good.
6.6.5 y7: Auto Skew Correction Retain
Determines whether or not to retain the original (uncorrected) skew of a
screen image after the print has been made.
Display
y7
setting
Function
*d0
d1
Retained
Not retained
6.6.6 yb: Magnification Warning Display
Select whether to display the magnification warning when the modification
of the standard magnification by an electronic zoom function.
Display
yb
setting
Function
*d0
d1
Not display
Display
6.6.7 yC: Print Reserve Function
Select whether to accept the print reserve function while the printer is
warming up.
Display
yC
setting
Function
d0
*d1
Not accepts
Accepts
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7
o mode Operations
6.7.1 o1: Inch/Metric Select
Select the inch or metric setting of the machine.)
Display
o1
setting
Function
d0
d1
Metric
Inch
6.7.2 o2: N-P Auto Exposure Coarse Adjustment
This adjustment is made when the image density on the print (scan)
output in the Auto Exposure mode is not satisfactory.
This adjustment is necessary after the replacement of PWB-A and PWB-
BB.
Be sure to adjust the Projection Lamp Voltage (F7) and
Shading Correction (b6) before this Adjustment.
1. Turn the Power Switch, set the Auto Exposure Mode into Auto and
select the center position of exposure level.
2. Make a print (scan) and check the image density.
<Conditions of printing/scanning>
Print Mode .............Text
Film Type ................Nega
3. Refer to the charts given below.
Then, adjust to desired image density by Function Mode o2.
o2
Setting
d4
Function
Image density
Lighter
4 step lighter
3 step lighter
2 step lighter
1 step lighter
Standard
d5
d6
d7
d8
d9
1 step darker
2 step darker
3 step darker
4 step darker
dA
db
dC
Darker
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.3 o3: P-P Auto Exposure Coarse Adjustment
This adjustment is made when the image density on the print (scan)
output in the Auto Exposure mode is not satisfactory.
This adjustment is necessary after the replacement of PWB-A and PWB-
BB.
Be sure to adjust the Projection Lamp Voltage (F7) and
Shading Correction (b6) before this Adjustment.
1. Turn the Power Switch, set the Auto Exposure Mode into Auto and
select the center position of exposure level.
2. Make a print (scan) and check the image density.
<Conditions of printing/scanning>
Print Mode .............Text
Film Type ................Posi
3. Refer to the charts given below.
Then, adjust to desired image density by Function Mode o3.
o3
Setting
d4
Function
Image density
Lighter
4 step lighter
3 step lighter
2 step lighter
1 step lighter
Standard
d5
d6
d7
d8
d9
1 step darker
2 step darker
3 step darker
4 step darker
dA
db
dC
Darker
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.4 o4: Scan Speed Adjustment
This operation is used to match the width on the Screen image with that
on the print (scan) image.
This adjustment is necessary after the replacement of PWB-BB.
Screen
Image
Feed Direction
A
B
1. Load the Film in the machine and make a print (scan).
<Conditions of printing/scanning>
Size: Letter (A4) Lengthwise
Centering:OFF
Masking:OFF
2. Measures the width of the image A on the Screen and on the print to
obtain any difference.
3. If the difference exceeds 0.6%, make the following adjustment.
4. Adjusting the o4 of the Function Mode so that the width distance
between A and B can be within 0.6%
o4
Setting
d5
Variation (%)
+1.92
+1.28
+0.64
0.00
Image
Larger
d6
d7
d8
d9
-0.64
dA
-1.28
db
-1.92
Smaller
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.5 o5: Adjustment of the image area Lengthwise Position
A
A
1. Load the Film in the machine and make a print (scan).
<Conditions of printing/scanning>
Size: Letter (A4) Lengthwise
Centering:OFF
Auto Masking:ON
2. Check the black band width of top
Image
and bottom on the print (scan)
image.
Top
3. Refer to the charts given below.
Then, adjust for top black band
width to become the same as
bottom black band width by Function
Mode o5.
A
Bottom
o5
Feed Direction
Setting
d5
Border Shift Value (mm)
-3
-2
-1
0
bottom frame increases
d6
d7
d8
d9
1
dA
2
top frame increases
db
3
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.6 o6: Adjustment of the Top and Bottom Frame Black Band
Width
1. Load the Film in the machine and make a print.
<Conditions of printing/scanning>
Size: Letter (A4) Lengthwise
Centering:OFF
Auto Masking:ON
2. Check the width of the black band
Image
running around the image area.
3. Refer to the charts given below.
Then, adjust to desired black band
width by Function Mode o6.
Top and
Bottom
Frame
o6
A
Setting Adjusted black band width (mm)
d5
d6
d7
d8
d9
dA
db
-6 3
-4 3
-2 3
0 3
2 3
4 3
6 3
band width decreases
Feed Direction
band width increases
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.7 o7: Adjustment of the Right and Left Frame Black Band Width
1. Load the Film in the machine and make a print (scan).
<Conditions of printing/scanning>
Size: Letter (A4) Lengthwise
Centering:OFF
Auto Masking:ON
2. Check the width of the black band
running around the image area.
Image
Right and Left Frame
3. Refer to the charts given below.
Then, adjust to desired black band
width by Function Mode o7.
o7
Setting Adjusted black band width (mm)
A
d5
d6
d7
d8
d9
dA
db
-6 3
-4 3
-2 3
0 3
2 3
4 3
6 3
band width decreases
Feed Direction
band width increases
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.7.8 o8: Projection lamp burn out detection (L2) setting
Select whether to detect L2 when Projection Lamp burn out.
Display
o8
setting
Function
*d0
d1
Detects
Not Detects
6.7.9 oA: Host Driver Setting
Set the Host Driver which uses at the PC mode.
Display
oA
setting
Function
*d0
d1
MS 6000
MS 2000
d2
MicroDAX (Fixed Window)
6.7.10 ob: Vender/Model Name Setting
Set the vender name and model name displayed in PC at the PC mode.
Display
ob
setting
Function
*d0
d1
d2
Minolta MS 6000
Minolta MS 2000
OEM Name
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.8
F mode Operations
6.8.1 F1: ROM Version Check
Used when checking the present ROM version of the machine.
1. Sets the function mode “F1”, and press the Start Key.
2. Shows the current ROM version number of the machine.
[Ex.] ROM Version "25" →"G0" → "01"...........Ver.25G001
6.8.2 F2: Scan Counter
Used when checking the total Scan Counter.
1. Sets the function mode “F2”, and press the Start Key.
2. Shows the current Scan Counter of the machine.
[Ex.] Display "02" → "46" → "12".........24,612 count
6.8.3 F3: Print Counter
Used when checking the total Print Counter.
1. Sets the function mode “F3”, and press the Start Key.
2. Shows the current Print Counter of the machine.
[Ex.] Display "01" → "23" → "45".........12,345 prints
6.8.4 F4: Counter Clear
This mode should be used to clear the scan counter and print counter.
1. Sets the function mode “F4”.
2. Press the setting mode memory key.
3. A display window blinks and counter is cleared.
4. Performs "F2" and "F3"and checks the scan counter and print counter.
6.8.5 F5: Control Panel LED Check
This mode should be used to light up the LEDs and check these functions.
1. Sets the function mode “F5”.
2. Press the print button to light up all LEDs on the Control Panel for
about 2 seconds.
6.8.6 F6: For Factory use
For factory adjustment. Do not use in field.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.8.7 F7: Projection Lamp Voltage Adjustment
This Adjustment is made to adjust the Projection Lamp Voltage.
This Adjustment is necessary after the replacement of the Projection
Lamp Regulator (PU2).
1. Remove the Optical Cover.
2. Remove the Projection Unit.
3. Insert the proves of a multi-
meter into the receptacle of 2P
connector locates at the right
side bottom of the machine.
(+) Test Prove: Pin 1 (Red cord)
(-) Test Prove: Pin 2 (Green cord)
4. Turn ON the Interlock Switch
(S201).
5. Connect the Power Plug with
the outlet and turn ON the
Power Switch.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6. Referring to the setting
procedure for Function mode,
set "F7".
7. To perform the adjustment,
press the Start key.
8. Rotate VR61 on PU2 so that the
reading voltage on the multi-
meter becomes DC21.5 0.2V.
9. Cancel the Function Mode.
10. Check the Projection Lamp
voltage in reader mode is
DC17.0 0.3V.
VR61
PU2
NOTE
In order to prevent damage of the Projection Lamp be careful of the
following items in adjustment.
➜
Do not exceed the DC21.7V during Projection Lamp voltage
adjustment.
➜
Makes full lighting time in F7 mode of the Projection Lamp into less
than 30 seconds.
6.8.8 F8: Reset the Setting Data
Function mode setting value and job program are reset to the default
value.
1. Sets the function mode “F8”.
2. Press the Mode Memory Key.
3. A display window blinks and setting data is cleared.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.9
b mode Operations
6.9.1 b1: Checking the Scan Table Unit Function
This mode should be used to check the Scan Table Unit Function.
Scan Position
Reader Position
1. Referring to the setting procedure for Function mode, set "b1".
2. Press the Start Key to move the Scan Table Unit to the Scan position.
3. Press the Start Key to move the Unit to the Reader position.
6.9.2 b2: Scanning mirror operation check
This mode should be used to check the Scan Mirror and the Scan Motor.
Scan
Prescan
1. Referring to the setting procedure for Function mode, set "b2".
2. Press the Start key, to perform scan operation (Scan and Prescan).
6.9.3 b3: For Factory use
For factory adjustment. Do not use in field.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.9.4 b4: Prism rotation operation check
Checks the rotation operation (AIR function) of a prism.
1. Referring to the setting procedure for Function mode, set "b4".
2. Press the Start Key to perform the 45 degree prism rotation.
(The screen image rotates 90 degrees. )
3. Whenever the Start Key pressed, prism repeats 45 degree rotation
(clockwise rotation and counterclockwise rotation).
6.9.5 b5: Single scan operation check
Checks single scan operation.
1. Referring to the setting procedure for Function mode, set "b5".
2. Press the Start Key to perform the single scan operation.
3. After the single scan operation has been completed, "b5" blinking on
the Multi-print Display lights up steadily and the machine completes
the operation.
4. Press the Start Key once again to perform single scan operation.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.9.6 b6: Shading Correction
This adjustment is necessary after the replacement of PWB-A or PWB-
BB.
1. Checks the surface of the 1st to 3rd scan path mirror and if dirty clean
it.
2. Place Projection Lens TYPE 2 in position and set a lens zoom ratio of
20X.
3. Load film and bring the image into focus.
(Do not move the focus ring after this operation).
4. Remove the Projection Lens and the Film Carrier.
5. Remove the Optical Cover and Prism from the machine.
6. Cover the entire Screen with a black sheet of paper to prevent an
extraneous light from striking the Screen.
7. Turn on the Power Switch and waits for 5 minutes and stabilizes
temperature of IC on PWB-A.
8. Set the function mode into "b6" and depress the Mode Memory key to
perform the Shading Correction.
9. The execution time of a Shading Correction is 10 minutes from about
6 minutes.
A Display changes as follows during Shading Correction execution.
H1→H2→H3→.....→H9→H0→1(E1)
When a display was set to "1" or "E1", Shading Correction was
completed.
(Displays "E1", when a printer is not connected)
10. When a Shading Correction carries out an unusual end on the way and
displays "C3", perform once again from Procedure 1.
11. After Shading Correction is completed, attach the Film Carrier and
Prism.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Mode and Adjustment
6
6.9.7 b7: Test Print Function
The test print of the printer can be executed.
1. Referring to the setting procedure for Function mode, set "b7".
2. Press the Start Key.
3. The following test prints are output by the printer.
Feeding Direction
6.9.8 b8: For Factory use
For factory adjustment. Do not use in field.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7
Troubleshooting
7.1
How to Use This Section
1. If a component on a P.W.Board or any other functional unit including
motor is defective, the booklet only instructs you to replace the whole
P.W.Board or functional unit and does not give troubleshooting
procedure applicable within the defective unit.
2. All troubleshooting procedures contained herein assumes that there
are no breaks in the harnesses and cords and all connectors are
plugged in the right positions.
3. For the removal procedure of covers and parts, refer to the
"DISASSEMBLY/CLEANING" section.
4. "GND" indicated in this booklet represents a 0-volt line of the circuit
concerned, equivalent to chassis ground; however, be sure to use the
Test Point (TP) on the PWB-D when creating a closed-circuit or
measuring voltage.
5. The procedures are given in the order of greater frequency of
occurrence of malfunctions and in the order of operation.
6. The procedures preclude possible malfunctions due to noise and other
external causes.
7. Refer to the wiring diagram of Appendix for wiring of electrical parts.
8. Since this manual has not indicated the trouble of the printer, refer to
the service manual of the printer.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.2
Malfunction Indications
Display
L2
Contents
Section
Projection Lamp malfunction
Scan Unit Drive malfunction
Scan Mirror Drive malfunction
Shading Correction malfunction
Cooling Fan Motor malfunction
Fusing malfunction
Scanner
C1
C2
C3
C4
C6
C7
C8
C9
CA
Cb
CL
PE
P0
Printer
Laser Diode malfunction
Polygon Motor malfunction
Main Motor malfunction
Cooling Fan Motor malfunction
Communication Error
Scanner or Printer
Scanner
Printer Clock malfunction
Paper Empty
Printer
Paper Size Error
P1
Paper Misfeed (Paper Take-up Section)
Paper Misfeed (Paper Transport Section)
Paper Misfeed (Fusing Section)
Printer Power OFF or Cable disconnect
Top Cover Open
P2
P3
E1
E2
If the above trouble is displayed, first perform the following works.
1. Turns off the power switch, and unplug the power cord.
2. After 10 seconds or more progress, plug the power cord and turns on
Power Switch.
When a trouble cannot be canceled and occurring frequently, it performs
troubleshooting with reference to subsequent page.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.3
Malfunction Detection Timing
7.3.1 L2: Projection Lamp malfunction
Display
L2
Detection Timing
When scan begins and the light of the Projection Lamp does not strike the CCD.
7.3.2 C1: Scan Unit Drive malfunction
Display
C1
Detection Timing
The Scan Position Sensor (PC4) is not activated within 2sec. after the Scan
Table has started moving to the printer position.
Scan Table
Motor (M2)
ON
OFF
Scan Position
Sensor (PC4)
OFF
ON
within 2sec.
The Reader Position Sensor (PC3) is not activated within 2sec. after the Scan
Table has started moving to the reader position.
Scan Table
Motor (M2)
ON
OFF
Reader Position
Sensor (PC3)
OFF
ON
within 2sec.
7.3.3 C2: Scan Mirror Drive malfunction
Display
C2
Detection Timing
The Scan Motor (M1) is not deenergized within 16 sec. after it has been
energized during a scan motion.
Scan Motor
(M1)
ON
OFF
16 sec.
The Scan Motor (M1) is not deenergized within 8 sec. after it has been
energized during a prescan motion.
Scan Motor
(M1)
ON
OFF
8 sec.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.3.4 C3: Shading Correction malfunction
Display
C3
Detection
When during shading correction (b6) the projection lamp light to CCD is few
unusually.
7.3.5 C4: Cooling Fan Motor malfunction
Display
C4
Detection Timing
A HIGH Cooling Fan Motor Lock Signal is output after the Power Switch is
turned ON.
Motor (M3,M4) stopped
C4
Cooling Fan
Motor Lock
Signal
H
L
within 5 sec.
7.3.6 Cb: Communication Error
Display
Cb
Detection Timing
Detected the following conditions 4 times during machine initialization.
•
No response of the printer in less than 100 msec. from command
transmission.
•
•
A parity error is in receiving data.
Receives a command error and a parity error.
7.3.7 CL: Printer Clock malfunction
Display
Cb
Detection Timing
•
The clock of the Oscillator (OSC1, 2) on the Printer I/F Board (PWB-EE) is
not suitable for the printer.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.4
Troubleshooting for malfunction code
7.4.1 L2: Projection Lamp malfunction
Check Item
Check LA1.
↓OK
Remedy
→NG
Replace LA1.
The carrier glass is covered by a dark
colored piece of paper or some other
thing that would prevent light from
shining through the glass.
→Yes
Remove paper or any other obstruction
from the carrier glass.
→No
Replace PWB-A.
Replace PWB-BB.
7.4.2 C1: Scan Unit Drive Malfunction
Check Item
Remedy
Does the Scan Table Drive Motor
rotate when the Power Switch is turned
ON?
→No
Wiring Check
Replace the following parts.
PWB-T
PWB-BB
M2
↓Yes
Is C1 shown when scanning motion?
→No
OK
↓Yes
Check PC3.
↓OK
→NG
Replace PC3.
Check PC4.
→NG
Replace PC4.
→OK
Replace PWB-BB.
7.4.3 C2: Scan Mirror Drive malfunction
Check Item
Remedy
Is C2 shown even when power is
turned OFF, then ON again?
→No
OK
↓Yes
Does the Scan Motor rotate when the
Power Switch is turned ON?
→Yes
Check Wiring.
Replace the following parts.
PWB-T
PWB-BB
M1
↓No
Check PC1.
↓OK
→NG
Replace PC1.
Check PC2.
→NG
Replace PC2.
→OK
Replace PWB-BB.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.4.4 C3: Shading Correction malfunction
Check Item
Remedy
Is C3 displayed during Function Mode →No
“b6” execution?
Replace PWB-BB.
Replace CCD Assy(PWB-A).
↓Yes
Performs the function mode (b6) once →NG
again. (Refers to the clause of
Replace PWB-BB.
Replace CCD Assy(PWB-A).
Shading Correction in chapter 6).
7.4.5 C4: Cooling Fan Motor malfunction
Check Item
Remedy
Is C4 shown even when power is
turned OFF, then ON again?
→No
OK
↓Yes
Does the Cooling Fan Motor (M3, M4) →Yes
turn smoothly after the Power Switch
has been turned ON?
Check Wiring.
Replace PWB-BB.
↓No
Check M3 and M4.
→NG
Replace M3.
Replace M4.
→OK
Check Wiring.
Replace PWB-BB.
7.4.6 Cb: Communication Error
Check Item
Remedy
OK
Is Cb shown even when power is
turned OFF, then turned ON again?
→No
↓Yes
Is the dedicated interface cable used? →No
Replace the Interface Cable.
Reconnect the Interface Cable.
↓Yes
Checks the connection of an interface →NG
cable.
↓OK
Replace the following parts sequentially.
Interface Cable
Printer I/F Board (PWB-EE) of Scanner
Interface Board of Printer
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.4.7 CL: Printer Clock malfunction
Check Item
Remedy
OK
Is CL shown even when power is
turned OFF, then turned ON again?
→No
↓Yes
Is the dedicated interface cable used? →No
Replace the Interface Cable.
Reconnect the Interface Cable.
↓Yes
Checks the connection of an interface →No
cable.
↓Yes
Confirm the frequency of the Oscillator →NG
on PWB-EE.
Reinstall the Oscillator.
or
Replace the Oscillator.
When using the MSP3000 Printer
OSC1: 42.3158MHz
OSC2: 95.2106MHz
When using the MSP2000 Printer.
OSC1: 19.5332MHz
OSC2: None
↓OK
Replace PWB-EE.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.5
Troubleshooting for malfunction
7.5.1 No Power
Check Item
Remedy
Has the Power Switch (S1) been
turned ON?
→ No
→No
→No
Turn on the Power Switch (S1).
↓Yes
Has the Power Cord been securely
connected to the machine?
Plug in the power cord.
↓Yes
Has the Power Cord been securely
plugged into the outlet?
Plug the power cord into the power
outlet.
↓Yes
Is the Fuse (F1) blown?
→Yes
Replace Power Fuse (F1).
↓No
Is the Interlock Switch (S201) in the
actuated position when the Projection
Unit is installed?
→No
Adjust the position of the Switch (S201).
↓Yes
Is the Fuse of PU1 blown?
→No
Replace PU1 or S201.
→Yes
Replace Fuse(F1) of PU1.
7.5.2 The Projection Lamp does not Light Up
Check Item
Check LA1.
↓OK
Remedy
→
NG
Replace LA1.
Check TS1.
↓OK
→
Replace TS1.
Check wiring.
NG
Is the voltage across CN7-1 and -2 approx.
DC17V when the Power ON/OFF switch is
in the ON position?
→
No
↓Yes
Is the source voltage developing across
PJ1-1 and -3 on PU2 when the Power ON/ No
OFF switch is in the ON position?
→
Check wiring.
↓Yes
Is the voltage across PJ3-1 on PU2 and
GND DC5V when the Power ON/OFF
switch is in the ON position?
→
Check wiring.
No
→
Yes
Replace PWB-BB.
Replace PU2.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.6
Electrical Components Check
7.6.1 LA1: Projection Lamp
1
Is the circuit across both terminals of the
Lamp conducting when the Lamp is removed
from the machine?
→No
Replace LA1.
→Yes
OK
7.6.2 M3: Power Unit Cooling Fan Motor
1
Does the Motor start rotating when the Power →Yes
ON/OFF Switch is turned ON?
OK
↓ No
2
Is the voltage across CN10-1 and GND
DC24V with the Power Switch in the ON
position?
→No
Check wiring.
Replace M3.
→Yes
7.6.3 M4: Projection Lamp Cooling Fan Motor
1
Does the Motor start rotating when the Power →Yes
ON/OFF Switch is turned ON?
OK
↓ No
2
Is the voltage across CN18-1 and GND
DC24V with the Power ON/OFF Switch in the
ON position?
→No
Check wiring.
Replace M4.
→Yes
7.6.4 PC1: Image Leading Edge Sensor
1
Is the voltage across PJ8-A3 on PWB-BB
and GND 0V when the Power Switch is in the
ON position and the light emitted by the
Sensor LED is blocked?
→No
Replace PC1.
↓ Yes
2
Is the voltage across PJ8-A3 on PWB-BB
and GND DC5V when the light emitted by the
Sensor LED strikes the Sensor
→No
Replace PC1.
OK
→Yes
photosensitive element?
7.6.5 PC2: Scan Mirror Position Sensor
1
Is the voltage across PJ8-B15 on PWB-BB
and GND 0V when the Power Switch is in the
ON position and the light emitted by the
Sensor LED is blocked?
→No
Replace PC2.
↓ Yes
2
Is the voltage across PJ8-B15 on PWB-BB
and GND DC5V when the light emitted by the
Sensor LED strikes the Sensor
→No
Replace PC2.
OK
→Yes
photosensitive element?
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.6.6 PC3: Reader Position Sensor
1
Is the voltage across PJ8-B12 on PWB-BB
and GND 0V when the Power ON/OFF
Switch is in the ON position and the light
emitted by the Sensor LED is blocked?
→No
Replace PC3.
↓ Yes
2
Is the voltage across PJ8-B12 on PWB-BB
and GND DC5V when the light emitted by the
Sensor LED strikes the Sensor
→No
Replace PC3.
OK
→Yes
photosensitive element?
7.6.7 PC4: Scan Position Sensor
1
Is the voltage across PJ8-A6 on PWB-BB
and GND 0V when the Power ON/OFF
Switch is in the ON position and the light
emitted by the Sensor LED is blocked?
→No
Replace PC4.
↓ Yes
2
Is the voltage across PJ8-A6 on PWB-BB
and GND DC5V when the light emitted by the
Sensor LED strikes the Sensor
→No
Replace PC4.
OK
→Yes
photosensitive element?
7.6.8 PU1: Power Unit
1
Is the Fuse of PU1 blown?
→Yes
Replace Fuse.
↓ No
2
Is the output voltage of each Connector
correct when the Power Switch is in the ON
position?
→No
Replace PU1.
OK
→Yes
7.6.9 PU2: Projection Lamp Regulator
1
Is the Fuse of PU2 blown?
→Yes
Replace Fuse.
↓ No
2
Is the voltage across CN7-1 and CN7-2
DC17.0V when the machine is in the reader
mode?
→No
Replace PU2.
OK
→Yes
7.6.10 S1: Power Switch
1
Are the circuits across 1 and 2, and 3 and 4 →Yes
conducting when the Power Switch is
removed from the machine and in the OFF
position?
Replace S1.
↓ No
2
Are the circuits across 1 and 2, and 3 and 4 →No
Replace S1.
OK
conducting when the Switch is in the
→Yes
position?
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.6.11 S201: Interlock Switch
1
Is the circuit across COM and NC terminals
conducting when the Switch is removed from
the machine?
→Yes
Replace S201.
↓ No
2
Is the circuit across COM and NC terminals
conducting when the Switch Actuator is
depressed?
→No
Replace S201.
OK
→Yes
7.6.12 TS1: Thermostat
1
Is the Reset Pin in the depressed position?
→No
Depress the Reset Pin.
↓ Yes
2
Is the circuit across both terminals of the
Thermostat conducting when the Thermostat
is removed from the machine?
→No
Replace TS1.
OK
→Yes
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
7.7
Image Troubleshooting
Trouble
Remedy
Black or blank print
•
Check the Projection Lamp (LA1) for
possible discoloration and breaks.
Adjust the Projection Lamp voltage (F7).
N-P/P-P AE Coarse adjustment (o1, o2).
Perform the Shading correction (b6).
Replace the PWB-A.
•
•
•
•
•
Replace the PWB-BB.
Black or white line in the feed direction
Black or white line in the scan direction
Uneven image
•
•
•
•
•
Clean the Scanner 1st to 3rd Mirrors.
Clean the CCD Cover glass.
Perform the Shading correction (b6).
Replace the PWB-A.
Replace the PWB-BB.
•
•
•
•
•
Clean the Scanner 1st to 3rd Mirrors.
Clean the CCD Cover glass.
Perform the Shading correction (b6).
Replace the PWB-A.
Replace the PWB-BB.
•
•
•
•
•
•
Clean the CCD Cover glass.
Perform the Shading correction (b6).
Adjust the Projection Lamp voltage (F7).
N-P/P-P AE Coarse adjustment (o1, o2).
Replace the PWB-A.
Replace the PWB-BB.
The Image abnormalities of the printer refer to the service manual of the
printer and perform the Troubleshooting.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
7
118
Download from Www.Somanuals.com. All Manuals Search And Download.
DWG.NO.
TITLE
0820-0003-51D
CIRCUIT DIAGRAM 1/1
MS 6000
MODEL
VOLTAGE
DATE ISSUED
AC100V/120V/220-240V
Jan. 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
DWG.NO.
TITLE
0820-0004-58A
WIRING DIAGRAM 1/4
MS 6000
MODEL
VOLTAGE
DATE ISSUED
AC100V/120V/220-240V
Jan. 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
DWG.NO.
TITLE
0820-0004-58A
WIRING DIAGRAM 2/4
MS 6000
MODEL
VOLTAGE
DATE ISSUED
AC100V/120V/220-240V
Jan. 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
DWG.NO.
TITLE
0820-0004-58A
WIRING DIAGRAM 3/4
MS 6000
MODEL
VOLTAGE
DATE ISSUED
AC100V/120V/220-240V
Jan. 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
DWG.NO.
TITLE
0820-0004-58A
WIRING DIAGRAM 4/4
MS 6000
MODEL
VOLTAGE
DATE ISSUED
AC100V/120V/220-240V
Jan. 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright
2001 MINOLTA CO,.LTD.
Printed In Japan
Use of this manual should be strictly
supervised to avoid disclosure of
confidential information.
0820-7993-11 01020160
Printed in Japan
This publication is printed
on recycled paper.
MINOLTA CO., LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Intel Computer Hardware 80219 User Manual
Intel Computer Hardware MB935 User Manual
Jabra Headphones BT650s User Manual
Jasco Portable Radio 97651 User Manual
JBL Car Stereo System MR 17 User Manual
John Lewis Dishwasher JLDWW 1205 User Manual
JVC DVD Player LET0239 001A User Manual
JVC Projector 0809TTH AO AO User Manual
JVC Speaker System CA UXP550 User Manual
Knoll Speaker Q450RS User Manual