JBL Car Stereo System MR 17 User Manual

COMPACT  
MARINE  
DIGITAL AUDIO  
Operation Manual  
for Users  
Model No.: MR-17  
PWR  
MR-17  
MODE  
MUT  
SH.  
SR  
MARINE  
0. LD  
FLIP DOWN / COMPACT DISC PLAYER  
2 INT  
3 RPT  
HI - POWER 4x45Watts  
7.SCN  
BD/FN  
1
4 RDM  
5
6
This product is sold and serviced exclusively by Prospec Electronics Inc. and must be returned  
to Prospec for in and out of warranty repairs. It can not be serviced under warranty by other JBL  
service centers. All products sold and serviced exclusively by Prospec Electronics Inc.  
For service contact us : 3325 South Morgans Point Road Mt Pleasant SC 29466  
Tel 843-849-9037  
Fax 843-849-9054  
Revised 28 / April / 05  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions and maintenance  
Contents  
1. Reset function  
A microprocessor reset button has been provided to facilitate manual resetting of  
the internal microprocessor. In the unlikely event that the player fails to operate  
correctly refer to step 2 below.  
Contents  
1
2
Note: It will be necessary to re-enter the radio preset memories as these will have  
been erased when the microprocessor is reset. After resetting the player,  
ensure all functions are operating correctly.  
Wiring Identification  
Installing and Removing the Detachable Face  
Important Notes  
3
CD DISC SLOT  
4
CD Eject button  
EJ  
2
1
Installation  
5
FRONT PANEL  
Supporting the Unit  
6
2. Caution  
1
RESET : If you are faced with a malfunction during the operation, simply press  
the reset button.  
Identification of Controls and Functions  
Controls  
7
2
CONNECTOR PIN : Always keep connector pin clean.  
If the PIN connector looks dirty, use cotton tips to clean it, so as to avoid any  
unexpected malfunction caused by dirt.  
8-9  
10  
11  
12  
13  
Station Tuning  
Operating the CD & CD Changer  
Precautions and Maintenance  
Trouble Shooting Guide & Specifications  
PLEASE NOTE: In order to receive Sirius Satellite radio broadcast, you must install  
JBL Sir2.5 as well as a satellite antenna (both sold separately).  
What is SIRIUS Satellite Radio?  
SIRIUS, headquartered in New York, offers over 120 cannels of digital quality radio  
transmitted across the continental US from three high-tech satellites. Along with offering  
a full spectrum of music genres, users can also listen to popular news, entertainment  
and sports channels. SIRIUS currently offers 65 music channels, 24 news channels  
(including traffic and weather), 7 sports channels (including two dedicated play-by-play  
channels) and 24 talk / entertainment channels.  
For more information on SIRIUS, visit siriusradio.com.  
12  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating the CD & CD changer  
Wiring identification  
(Remote control)  
12  
3
14  
1
13  
B
C
(SIRIUS control)  
PWR  
MR-17  
D
MODE  
(AUX-IN)  
MUT  
15  
SH.  
SR  
MARINE  
0. LD  
F
2
(ANT. socket)  
FLIP DOWN / COMPACT DISC PLAYER  
HI - POWER 4x45Watts  
7.SCN  
BD/FN  
(CD changer socket)  
1
2 INT  
3 RPT  
4 RDM  
5
6
E
A
CONNECTOR  
18  
9
11  
4
5
6
7
8
10  
16  
17  
FUSE  
1A  
Blue  
1. Loading a CD  
Open the door by pushing button (14).  
Insert a CD label side up into the slot opening, then close the door.  
The CD will begin playing automatically after it is loaded.  
(AUTO ANT)  
FUSE  
10A  
Yellow  
Black  
Red  
( BACK-UP B+ )  
( GROUND )  
Gray  
Rear Line out  
Red  
( IGNITION B+ )  
White  
Red  
Notes:  
NEVER insert foreign objects into the CD slot opening.  
Black  
Front Line out  
If a CD is difficult to insert, there may already be a CD loaded in the unit.  
Some recorded CD-Rs or CD-RWs may not be usable with this CD player.  
White  
Gray  
White  
( Front Right )  
( Front Left )  
( Rear Left )  
White/Black  
Gray/Black  
2. Select the CD->CDC by pressing the "MODE" button (3) .  
Green  
Violet  
( Rear Right )  
Green/Black  
Violet/Black  
3. Press preset button (10) or (11) to choose the DISC that you would like to play.  
(This button works when you install the CD changer to the radio unit. CDC is optional.)  
Installation Notes  
Applicable to both 2 and 4-speaker connection:  
A. Connections  
4. Play / Pause (6)  
Push to pause and push again to resume play.  
B. Din cable connection for remote control  
C. Din cable connection for SIRIUS control  
D. AUX-IN  
5. Intro Scan (7)  
Press this button to hear the first 10 seconds of each track on the disc.  
Press this button again to restore the player to its normal play mode.  
E. CD changer socket  
F. Antenna socket  
6. Repeat play button (8)  
While playing a desired track, press RPT button to play the track repeatedly.  
Press RPT button again to return to normal play mode.  
This radio contains four separate power amplifiers. To prevent possible damage to  
these amplifiers please ensure the following:  
7. Random play button (9)  
Press RDM button to play all tracks on a CD in random sequence.  
Press RDM button again to return the player to normal mode.  
i) The boat chassis is not used as a loudspeaker ground(-).  
ii) Front and rear loudspeaker connecting wires are not joined together.  
iii) Any wires not used when completing a two speaker installation are fully insulated.  
iv) The memory wire (yellow) is connected to a permanent + 12V supply.  
v) The power wire (red) is connected via the ignition switch of the boat.  
8. Track Tuning (15)  
Search the tracks on the DISC with the  
and  
the or button continuously, the track goes fast - forward  
buttons. If you press and hold  
or rewinds  
.
2
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing and Removing the Detachable Face  
Station Tuning  
To Install / attach the faceplate:  
Place the detachable face place onto  
the radio one side at a time so that the  
grooved edge of the face plate lines up  
directly with the connecting piece on  
the radio. The face plate should fit easily  
inside the plastic trim. When the face  
plate is securely in place, a distinct  
clickwill be heard, indicating that it is  
locked correctly in place.  
Close Up of Side View  
3
12  
13  
14  
1
PWR  
MR-17  
MODE  
MUT  
15  
SH.  
SR  
MARINE  
0. LD  
2
FLIP DOWN / COMPACT DISC PLAYER  
HI - POWER 4x45Watts  
7.SCN  
BD/FN  
1
2 INT  
3 RPT  
4 RDM  
5
6
6
16  
4
5
9
11  
18  
7
8
10  
17  
To remove the face plate:  
1. Press Release button, then the front panel will open (fold down).  
1. Manual/Seek tuning buttons (15): Press this button quickly to activate the Seek  
mode. The Seek mode will automatically seek up or down the wave band and stop at  
the next station of sufficient signal strength. Press and hold tuning buttons for 2  
seconds to enter manual tuning mode. The unit will revert back to Seek mode after  
10 seconds without use.  
Release button  
MUT  
Front Panel  
MARINE  
0. LD  
4x45Watts  
6
7.SCN  
2. Manual Station store: Select the desired band and tune to a radio station to be  
memorized. Choose the preset button memory location1-6 into which the station is  
to be stored and press and hold that preset button for 2 seconds.  
2. Grip the release section and pull the front panel forward.  
- Be careful not to grip the front panel display too tightly or to drop the panel.  
The station will now be entered into the preset memory. 6 stations can be memorized  
on each of the FM1, FM2, FM3, AM1, AM2.  
Release section  
3. A.PS - Auto store function (18)  
Press and hold button (18) for approximately 2 seconds until you hear a beep which  
confirms the memory function is engaged. The unit will "SEARCH" for six strong  
stations and automatically store them on buttons 1 - 6.  
3. Close the inner cover.  
- After removing the front panel, be sure to close the inner cover to prevent dirt,  
dust or other foreign matter from entering the CD slot.  
You can override the preset station on any button by manually setting a new frequency.  
4. Scan (16)  
In Radio mode, press the SCAN (16) button to scan strong stations for previewing.  
At the desired station press the "SCAN (16)" button again to stop scanning.  
Inner Cover  
5. Program Memory Scan  
Momentarily press A.PS and the unit will scan for stored stations.  
Momentarily press it again to stop scanning.  
4. Keep the detachable front panel in the protective case provided.  
Carrying Case  
Front Panel  
10  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important notes  
Controls  
Prior to the final installation, carry out a sound check. If high distortion or intermittent  
sound is experienced, it is possible that the wiring from the CD receiver to the boat's  
electrical system is poor or that the battery needs recharging.  
If the battery and its charging circuit are OK, then rewire the yellow fused wire of the  
CD player directly to the positive terminal (+) of the boat battery.  
c. Area Selection  
By pressing SEL(2) button again, the unit will be in Area Selection mode, then turn the  
knob right or left to choose USA or EUR. Press and hold BD/FN for 2 seconds to confirm  
selection.  
d. DSP  
Choose from flat, classic, pop or rock by pressing the SEL(2) button again. Adjust with  
spindle knob.  
Marine accessory shops stock the connector blocks and the 10 Amp cable that may  
be necessary for extending the fuse wire connection.  
Grounding  
3.Volume control  
Turn the spindle knob (2) left or right to decrease or increase the volume level.  
The radio will automatically default to volume mode when powered on.  
Make sure that the black wire on the wiring harness is connected to a good ground  
point on the boat. If the chassis of the boat is used as a grounding point, make sure  
that the surface is scraped clean of paint before attaching the wire to it.  
It is preferable to connect the black ground wire directly to negative terminal (-) of  
the boat battery.  
- Bass control  
Turn left to decrease the bass.  
Turn right to increase the bass.  
- Treble control  
Warning: polarity...  
This model is only suitable for use in boats which have a Negative ground system,  
e. g. : the negative terminal of the boat battery is connected to the chassis.  
Turn left to decrease the treble.  
Turn right to increase the treble.  
- Balance control  
Turn left to decrease the right speaker volume.  
Turn right to decrease the left speaker volume.  
- Fader control  
Turn left to decrease the volume level of any speakers connected to the front channel.  
Turn right to decrease the volume level of any speakers connected to the rear channel.  
4."MODE" button (3)  
Press this button to select Radio, CD, CDC, SIRIUS or AUX-IN.  
POSITIVE  
CHASSIS  
NEGATIVE  
CHASSIS  
5. BD/FN button (5)  
Press the BD/FN(5) button shortly to select the desired band:FM1,FM2,FM3, AM1  
and AM2.  
Connecting the Speakers and Power Cables  
Before you wire your system, disconnect your boat battery's positive (+) cable.  
This helps prevent damage in case of a short. When you complete the wiring,  
reconnect the battery cable and test your marine stereo. When connecting your  
marine stereo's black ground wire, be sure to connect the wire to a metal part of  
your boat or preferably to the negative (-) terminal of the boat battery.  
6. SHIFT / SCROLL button (4)  
SIRIUS function button only.  
7. How to adjust the clock / time (17)  
Press DIS(17) button once to display the time.  
a. Press and hold the DIS (17) button until the time flashes on the display.  
b. Turn spindle knob(2) clockwise to set hour.  
c. Turn spindle knob(2) counter clockwise to set minutes.  
d. Press the DIS button again quickly to accept the adjusted time.  
If no button is pressed within 5 seconds, then it automatically accepts the adjusted  
time without further intervention from the user.  
8. Loudness function (13)  
In order to emphasize the bass and the treble at low volume, press the LD (13) button.  
To turn off loudness, press the LD button again.  
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls  
Installation  
3
12  
13  
14  
1. Precautions  
Choose the mounting location carefully so that the unit will not interfere with the  
normal driving functions of the boat.  
1
PWR  
MR-17  
Avoid installing the unit where it would be subject to high temperature, such as from  
direct sunlight or hot air, or where it would be subject to dust, dirt or excessive  
vibration. Use only the supplied mounting hardware for a safe and secure installation.  
Be sure to remove the front panel before installing the unit.  
MODE  
MUT  
15  
SH.  
SR  
MARINE  
0. LD  
2
FLIP DOWN / COMPACT DISC PLAYER  
HI - POWER 4x45Watts  
7.SCN  
BD/FN  
1
2 INT  
3 RPT  
4 RDM  
5
6
2. Mounting angle adjustment  
Adjust the mounting angle to less than 20 degrees from horizontal.  
6
16  
4
5
9
11  
18  
7
8
10  
17  
3. Mounting example  
1. POWER ON/OFF button (1)  
Push the PWR button (1) to turn on the unit. Push the button again to turn off the unit.  
<< Installation in the cabinet >>  
1
2
2. SEL and VOL button (2)  
1) Audio control ( VOLUME / BASS / TREBLE / BALANCE / FADER )  
Short pressing the SEL (2) button you can select which of the below features to set:  
-VOL display - volume control > press button (2)>  
-BAS display - bass tone control >press button (2)>  
-TRB display - treble tone control > press button (2)>  
-BAL display - balance control > press button (2)>  
-FAD display - fader control > press button (2)>  
Half Cabinet  
Release Key  
3
4
Tap  
Then use the spindle knob(2) to adjust. In each mode, the waiting time is about 5 seconds.  
If the waiting time is over, it returns to the last display mode of Radio, CD, or CDC mode.  
These settings are indicated on the display window.  
Bend these claws, if necessary.  
VOLUME  
Select  
BASS  
Select  
TREBLE  
Note: Keep the release key in a safe place as you may need it in future to remove  
the unit from the boat.  
Select  
FADER  
Select  
BALANCE  
Select  
2) Beep 2nd , I-Vol , Area and DSP Selection  
When the SEL button (2) is pressed over 2 seconds, the unit will be operated as below:  
4. Attaching the Trim Ring  
- Attach the Trim Ring to the Radio after installing.  
- Be sure to insert the Trim Ring in the correct direction.  
Beep 2nd  
I-Vol  
Area  
DSP  
Press  
Press  
Press  
a. Beep 2nd  
In the Beep 2nd mode, you can control Beep on or Beep 2nd by turning the spindle knob.  
- Beep on : You can hear "beep" sound when you press any buttons.  
- Beep 2nd :You can hear "beep" sound when you press a button over 1.5 seconds.  
b. I-Vol  
By pressing the SEL(2) button again, the unit will turn to I-VOL mode (Initial Volume Level  
Adjustment). You can adjust the I-Vol to the level you want by turning the spindle  
knob. After setting the initial level, when the unit is powered on/off, detached on/off, or  
when the ACC is turned on/off, the I-VOL will keep the volume adjusted to the preset level  
when unit is turned on.  
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Identification of controls and functions  
Supporting the unit  
3
1
12  
13  
14  
3
PWR  
MR-17  
MODE  
3
MUT  
5
15  
SH.  
SR  
4
MARINE  
0. LD  
2
7
2
9
FLIP DOWN / COMPACT DISC PLAYER  
HI - POWER 4x45Watts  
7.SCN  
BD/FN  
1
2 INT  
3 RPT  
4 RDM  
5
6
6
16  
4
5
9
11  
18  
7
8
10  
17  
1. POWER ON / OFF button  
2. Electronic Function SELECT button, Volume decrease or increase button  
1
3. MODE button <Radio CD CDC SIRIUS  
4. SH. SR (SHIFT / SCROLL) button (SIRIUS only)  
5. BD / FN button  
AUX-IN>  
6
1. UNIT  
2. RELEASE CASE  
3. HEX NUT  
6. CD play / pause button, radio preset 1 button  
7. CD intro scan button, radio preset 2 button  
8. CD repeat track button, radio preset 3 button  
9. CD random play button, radio preset 4 button  
4. LOCK WASHER  
5. PLAIN WASHER  
6. BODY  
Lock Washer  
Plain Washer  
8
7. REAR SUPPORT STRAP  
8. TAPPING SCREW  
9. M5 X 20 HEX BOLT  
10. DISC DOWN (CD changer) button, radio preset 5 button  
11. DISC UP (CD changer), radio preset 6 button  
12. MUTE button  
13. LOUD (loudness) button (#0 SIRIUS only)  
14. Front panel release button  
Accessories subject to change without notice.  
1. Fuse replacement  
15. Radio tune UP / DOWN button, CD track UP / DOWN button  
16. SCAN button (#7 SIRIUS only)  
If the fuse blows, check the power connection and replace the fuse. If the fuse blows  
again after the replacement, there may be an internal malfunction. In this case,  
consult your nearest dealer.  
17. DISP (display) button (#8 SIRIUS only)  
18. A.PS - Auto Preset Scan button (#9 SIRIUS only)  
2. Warning  
Use the specified amperage fuse for each lead.  
Use of a higher amperage fuse may cause serious damage.  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia Radio NS R5111 User Manual
Intel Handheld Game System SIM4 02 User Manual
Jasco Mouse 98505 User Manual
JBL Car Amplifier GTO3501 User Manual
JL Audio Car Stereo System E1400D User Manual
JVC Portable CD Player RD EZ11 User Manual
JVC Stereo System 0306MOCMDWJSC User Manual
Kenwood Network Cables KCA iP102 User Manual
KitchenAid Ice Maker KUIC15PRTS1 User Manual
Kodak Camera Accessories K625 User Manual