Download from Www.Somanuals.com. All Manuals Search And Download.
Features
ꢀ PEN™ Dome Tweeter with Neodymium Magnet
provides a smooth high frequency response with quick, detailed
and spatially-correct imaging for the KS35, KS40, KS410 and
KS46. PEN is an acronym for the space age material
“biaxially oriented polypropylene naphthalate film”--your
parents’ tax dollars probably paid for its development, you
might as well enjoy it.
ꢀ CIMP™ (Curvilinear Injection-Molded Polypropylene
Woofer Cones) is a high performance composite, which
remains rigid, minimizes cone flex and lowers harmonic
distortion. The CIMP™ consists of a one-piece,
injection-molded polypropylene material that moves as a
piston, exhibiting power and control.
ꢀ New 20mm Titanium Dome Tweeters with extended
High Frequency Response enable the KS525, KS60,
KS65, KS68 and KS693 coaxial speakers to respond to the
most demanding sound tracks up to 21 kHz.
ꢀ New Enhanced BAM (Basket and Motor) Assembly
utilizes a high strength steel basket, features a low-profile open
design, and provides a solid foundation for the
precision-aligned motor assembly.
ꢀ New Santoprene™ Surround Radius allows extended
cone excursion for additional bass output and higher SPL.
Santoprene™ is the next generation of surround material.
It offers unmatched acoustical dampening and UV protection,
and gives the KS-Series Coax cone maximum EXmax™
(effective excursion) potential.
ꢀ Optimized 25mm Titanium Dome Tweeters with
expanded Frequency Response empower the KS69
coaxial speakers to reproduce the most life-like crescendos up
to 21,000 Hz!
ꢀ High-Temp Polyimide Film Voice Coil Former
improves sonic and conductive properties, and prevents
thermal-electrical meltdown.
ꢀ Flexible Mounting of the KS40 (utilizes breakaway tabs),
the KS60 (fits small and large 6 inch / 15.2 cm openings), and
the KS68 (fits factory 5” x 7” / 12.7 cm x 17.8 cm and
6” x 8” / 15.2 cm x 20.3 cm locations), enable the KS-Series
Coax Speakers to accommodate most installations.
ꢀ Ferro-Fluid™ cooled tweeter voice-coil extends the high
frequency transducer’s life span.
ꢀ Kicker Marine Ready models come with water resistant
mounting hardware. This enables the KS60, KS69 and KS693
to replace most stock boat speakers without rusting your ship.
ꢀ High-Power Tinsel Lead Wires eliminate broken leads and
power loss, due to the common use of “insufficient-gauge” lead
wires.
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-Series Coax Speakers
3
Performance
KS35
Model:
KS40
KS410
KS46
KS525
Speaker Design
2 - Way
4
2 - Way
4
2 - Way
2 - Way
2 - Way
4
Rated Impedance, ohm
DC Resistance, ohm
4
4
3
3
3
3
3
Sensitivity [SPLo], dB @ 1W, 1m
Power Range, Watts RMS
Peak Power Handling, Watts
Effective Frequency Range, Hz
Top-Mount Depth, in (cm)
Bottom-Mount Depth, in (cm)
Mounting Hole Diameter, in (cm)
Frame Diameter, in (cm)
Woofer Size, in (cm)
88
88
88
88
90
5-20
5-30
5-30
5-30
5-45
40
60
60
60
135
80-20k
60-20k
45-20k
2 7/16 (6.2)
2 3/4 (7.0)
50-20k
1 13/16 (4.6)
2 (5.1)
45-21k
2 (5.1)
2 1/4 (5.7)
1 9/16 (4.0)
1 7/8 (4.8)
3 3/16 (8.1)
3 7/16 (8.7)
3 1/2 (8.9)
Polypropylene
Santoprene
1/2 (1.3)
1 13/16 (4.6)
2 1/16 (5.2)
3 11/16 (9.4)
4 (10.2)
4 (10.2)
Polypropylene
Santoprene
1/2 (1.3)
3 7/8 x 9 5/16 (9.8x23.7) 3 1/2 x 5 3/4 (8.9x14.6) 4 9/16 (11.6)
4 3/8 x 10 (11.1x25.4)
4 x 10 (10.1x25.4)
Polypropylene
Santoprene
3 13/16 x 6 (9.7x15.2)
4 x 6 (10x15.2)
Polypropylene
Santoprene
1/2 (1.3)
5 1/8 (13.0)
5 1/4 (13.3)
Polypropylene
Santoprene
3/4 (2.0)
Dome
Woofer Cone Material
Woofer Surround Material
Tweeter Size, in (cm)
1/2 (1.3)
Tweeter Design
Balanced Dome Balanced Dome Balanced Dome
Balanced Dome
PEN
Tweeter Diaphragm Material
Tweeter Magnet Material
Tweeter Protrusion, in (cm)
Midrange Size, in (cm)
Midrange Design
PEN
PEN
PEN
Titanium
Neodymium
1/4 (.64)
N / A
Neodymium
1/8 (.32)
N / A
Neodymium
1/8 (.32)
N / A
Neodymium
0 (0)
Neodymium
1/16 (.16)
N / A
N / A
N / A
N / A
N / A
N / A
N / A
Midrange Cone Material
Grills Included
N / A
N / A
N / A
N / A
N / A
No
Yes
No
No
Yes
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-Series Coax Speakers
4
Performance
KS69
Model:
KS60
KS65
KS68
KS693
Speaker Design
2 - Way
4
2 - Way
4
2 - Way
2 - Way
3 - Way
Rated Impedance [Zn], ohm
DC Resistance, ohm
4
4
4
3
3
3
3
3
Sensitivity [SPLo], dB @ 1W, 1m
Power Range, Watts RMS
Peak Power Handling, Watts
Effective Frequency Range, Hz
Top-Mount Depth, in (cm)
Bottom-Mount Depth, in (cm)
Mounting Hole Diameter, in (cm)
Frame Diameter, in (cm)
Woofer Size, in (cm)
90
90
90
92
92
5-65
5-65
5-60
5-90
5-100
195
195
180
270
300
43-21k
1 15/16 (4.9)
2 1/4 (5.7)
5 (12.7)
6 1/4 (15.9)
6 (15.3)
Polypropylene
Santoprene
3/4 (2.0)
Dome
40-21k
2 1/8 (5.4)
2 1/4 (5.7)
5 5/8 (14.3)
6 1/2 (16.5)
6 1/2 (16.5)
45-21k
30-21k
30-21k
2 3/8 (6.0)
2 3/4 (7.0)
5 x 7 (12.7x17.8)
3 3/16 (8.1)
3 5/8 (9.2)
6 x 8 9/16 (15.2x21.7)
3 3/16 (8.1)
3 5/8 (9.2)
6 x 8 9/16 (15.2x21.7)
5 1/2 x 7 1/2 (14.0x19.1) 6 5/8 x 9 3/16 (16.8x23.2) 6 5/8 x 9 3/16 (16.8x23.2)
6 x 8 (15.2x20.3)
6 x 9 (15.2x22.9)
Polypropylene
Santoprene
1 (2.5)
6 x 9 (15.2x22.9)
Polypropylene
Santoprene
3/4 (2.0)
Woofer Cone Material
Polypropylene Polypropylene
Woofer Surround Material
Tweeter Size, in (cm)
Santoprene
3/4 (2.0)
Dome
Santoprene
3/4 (2.0)
Dome
Tweeter Design
Dome
Dome
Tweeter Diaphragm Material
Tweeter Magnet Material
Tweeter Protrusion, in (cm)
Midrange Size, in (cm)
Midrange Design
Titanium
Neodymium
1/2 (1.3)
N / A
Titanium
Neodymium
7/16 (1.1)
N / A
Titanium
Neodymium
1/4 (.64)
N / A
Titanium
Neodymium
0 (0)
Titanium
Neodymium
3/8 (.95)
N / A
1 (2.5)
N / A
N / A
N / A
N / A
Dome
Midrange Cone Material
Grills Included
N / A
N / A
N / A
N / A
Titanium
Yes
Yes
Yes
No
Yes
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-Series Coax Speakers
5
Installation
Your Kicker KS-Series drivers are specifically designed for mounting in free-air applications. The speakers do not require a sealed
enclosure for optimum performance. It is important to isolate the sound coming off the front of the driver from the sound radiating from
the back of the driver. This isolation is usually accomplished by using the correct size driver in a factory speaker location.
Mounting
Use caution when mounting speakers through the rear deck or package tray of a vehicle. Please be aware of wiring harnesses,
trunk springs, hinges, and folding seat mechanisms that may interfere with the operation of the car or speaker system. When running
the speaker wires, be careful not to damage them with seat bolts or door screws.
Note: To get the best performance from your KS-Series Coax Speakers,
we recommend using genuine Kicker Accessories and Wiring.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
KS-Series Coax Speakers
Installation
If custom door mounting locations for the KS-Series Coax Speakers are desired, be careful to avoid interference from the window
and door lock mechanisms. The first step is to find a location on the door panel that will accept the dimensions of the speaker. Then
remove the door panel from the door, and check for operational clearance of the window. Cycle the window all the way down and up.
If metal must be cut to mount the speakers, avoid structural metal and braces. An optional reinforcing panel (thin piece of wood or
Medium Density Fiberboard) may be necessary if the door panel cannot support the weight of the speaker. Mount the speaker to the
door panel and door body as outlined in Figure 1.
If the factory door speaker wiring is not available, it will be necessary to run the supplied wire through the door jamb. The speaker
wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. An existing grommet in the door
jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole
to run the speaker wire through the door jam. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is
run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage as outlined in Figure 2.
Figure 1
Figure 2
(Optional)
Stagger Holes
For Wiring &
Use Grommets
(When Factory Holes and
Grommets are not Available)
Door Panel
To Crossover
Kick Panel
Grill Mounting Ring
Push Grill into place and
snap onto Grill Mounting Ring
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-Series Coax Speakers
7
Wiring Options
Wiring
Hooking up the supplied wires to your Kicker KS-Series Coax Speakers is easy. The end of each wire is terminated with a large
and a small connector. The larger connector is crimped to the gray wire and connects to the larger positive terminal of the speaker.
The smaller connector is crimped to the black wire and connects to the smaller negative terminal of the speaker. The other end of
these wires connect to your source unit or amplifier in a similar manner. The gray wire connects to the positive output of the amplifier
or source unit. The black wire connects to the negative output of the amplifier or source unit. These connections can be made with
the crimp-down style connectors, or with solder and heat shrink or electrical tape to prevent electrical shorting of the speakers.
Note: To get the best performance from your Kicker KS-Series Coax Speakers, we recommend using genuine Kicker Accessories
and Wiring.
SOURCE UNIT or AMPLIFIER
Other
Channel
If you have any questions about the installation of your Kicker KS-Series Coax Speakers, see the Authorized Kicker Dealer where you
made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose
the Technical Support tab, choose subject you are interested in, and then download or view the corresponding information; or E-mail
[email protected]. Please call Technical Services (405) 624-8583 for unanswered or specific questions.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
KS-Series Coax Speakers
Wiring Options
Wiring two KS-Series Coax Speakers to a single channel
Modern high performance coaxial speakers have a lower DC Resistance than what used to be available. The Kicker KS-Series
Coax Speakers are rated at four ohms and work with any source unit or amplifier designed to operate at a four ohm load. If you want
to use two KS-Series Coax Speakers on each channel of your source unit or amplifier wire the speakers in series, as shown below.
This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the source unit or amplifier. This
may prevent an amplifier from shutting down, due to over-current protection circuitry.
SOURCE UNIT or AMPLIFIER
All specifications and performance figures are subject to change. Please visit kicker.com for the most current information.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
KS-Series Coax Speakers
WHAT IS NOT COVERED?
Acoustics LIMITED WARRANTY
This warranty is valid only if the product is used for the purpose for which it was
designed.
It does not cover:
Kicker warrants this product to be free from defects in material and workmanship
under normal use for a period of THREE (3) MONTHS from date of original
purchase with receipt. When purchased from an Authorized KICKER Dealer it is
warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases
you must have the original receipt! Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction during the
warranty period, Kicker will repair or replace (at its discretion) the defective
merchandise with equivalent merchandise at no charge. Warranty replacements
may have cosmetic scratches and blemishes. Discontinued products may be
replaced with more current equivalent products.
•
•
•
Damage due to improper installation.
Subsequent damage to other components.
Damage caused by exposure to moisture, excessive heat, chemical cleaners,
and/or UV radiation.
Damage through negligence, misuse, accident or abuse. Repeated returns for
the same damage may be considered abuse.
•
•
•
•
•
•
•
•
•
•
Any cost or expense related to the removal or reinstallation of product.
Speakers damaged due to amplifier clipping or distortion.
Items previously repaired or modified by any unauthorized repair facility.
Return shipping on non-defective items.
Products with tampered or missing bar code labels.
Products returned without a Return Authorization (RMA) number.
Freight Damage.
This warranty is valid only for the ORIGINAL PURCHASER and is not extended
to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are limited in duration to a period of the express warranty as
provided herein beginning with the date of the original purchase at retail, and no
warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties, therefore these exclusions may
not apply to you. This warranty gives you specific legal rights; however you may
have other rights that vary from state to state..
The cost of shipping product to Kicker.
Service performed by anyone other than Kicker.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise should be returned to your local Authorized Stillwater
Designs (Kicker) Dealer for warranty. Assistance in locating an Authorized Dealer
can be obtained by writing, calling, or by visiting kicker.com. You can confirm that a
dealer is authorized by asking to see a current authorized dealer window decal.
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 24-hour service for all acoustics (subwoofers,
midrange drivers, tweeters, crossovers, etc) returns. Delays may be incurred if lack
of replacement inventory or parts is encountered.
If it becomes necessary for you to return defective merchandise directly to
Stillwater Designs (Kicker), call the Kicker Customer Service Department at
(405) 624-8510 for a Return Authorization (RMA) number. Package all defective
items in the original container or in a package that will prevent shipping damage,
and return to:
INTERNATIONAL WARRANTY
Contact your International Kicker dealer or distributor concerning specific
procedures for your country’s warranty and service policies.
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please
return only defective components (speaker, grill connector, etc.). The return of
functioning items increases your return freight charges. Non-defective items
received will be returned freight collect.
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510
KICKER drivers are capable of producing sound levels
that can permanently damage your hearing! Turning up a
system to a level that has audible distortion is more
damaging to your ears than listening to an undistorted
system at the same volume level. The threshold of pain
is always an indicator that the sound level is too loud and
Include a copy of the original receipt with the purchase date clearly visible, and a
“proof-of-purchase” statement listing the Customer’s name, Dealer’s name and
invoice number, and product purchased. Warranty expiration on items without proof-
of-purchase will be determined from type of sale and the manufacturing date code.
Freight must be prepaid; items sent freight collect, or COD, will be refused.
WARNING:
may permanently damage your hearing.
Failure to follow these steps may void your warranty. Any questions can be
directed to the Kicker Customer Service Department at (405) 624-8510.
Please use common sense when controlling volume!
Download from Www.Somanuals.com. All Manuals Search And Download.
08112005+05.5KS
10
KS-Series Coax Speakers
Tech Lines
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-Series Coax Speakers
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|