AUDIO VIDEO SURROUND RECEIVER
VR-806
KRF-V5080D
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual is for some models. Model availability and features
(functions) may differ depending on the country and sales area.
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this model has several operation
modes. These modes enable the remote control to control other audio/video components. In order to
effectively use the remote control it is important to read the operating instructions and obtain a proper
understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations.
B60-5439-00 00 MA (K, P, X, Y)
0311
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Contents
Channel space switching
(Except for the U.S.A., Canada and Australia)
Caution : Read the pages marked
safe operation.
carefully to ensure
The space between radio channels has been set to the one that
prevails in the area to which the system is shipped. However, if the
current channel space setting does not match the setting in the area
where the system is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice versa, proper
reception of AM/FM broadcasts cannot be expected. In this case,
change the channel space setting in accordance with your area by
referring to the following table.
Before applying the power........................................................ 2
Safety precautions .................................................................... 2
How to use this manual............................................................ 2
Unpacking ................................................................................. 2
Channel space switching .......................................................... 3
Preparing the remote control ................................................... 4
Special features ........................................................................ 5
Names and functions of parts ................................................... 6
Main Unit .................................................................................. 6
Remote control unit .................................................................. 7
CHANNEL
Area
Space Frequency
U.S.A., Canada and South
American countries
FM: 100 kHz
AM: 10 kHz
1.
2.
FM: 50 kHz
AM: 9 kHz
Other countries
Setting up the system........................................ 8
Connecting audio components.......................... 9
Connecting video components........................ 10
Connecting video components(COMPONENT
VIDEO) ............................................................. 11
Digital connections .......................................... 12
Connecting a DVD player (6 - channel input)
(KRF-V5080D only) ........................................... 13
Connecting the speakers ................................. 14
Connecting the terminals ................................ 15
Connecting the antennas................................. 15
Preparing for surround sound ....................... 16
Speaker settings .............................................. 16
75us
50us
AM 10kHz
FM100kHz
AM 9kHz
FM50kHz
Preparations
DE-EMPHASIS
CHANNEL SPACE
Turn the power OFF by pressing the POWER key before moving the
switch level. Move the switch lever to match your area with a small
screwdriver or other pointed tool, then turn the power ON again.
Normal playback.............................................. 18
Preparing for playback ..................................... 18
Listening to a source component .................... 19
Adjusting the sound ......................................... 19
Recording .......................................................... 20
Recording audio (analog sources) ................... 20
Recording video ............................................... 20
Recording audio (digital sources) .................... 20
Listening to radio broadcasts ....................... 21
Tuning radio stations ....................................... 21
Presetting radio stations manually .................. 22
Receiving preset stations ................................ 22
Receiving preset stations in order (P.Call) ...... 22
Ambience effects ............................................. 23
Surround modes .............................................. 23
Surround play ................................................... 25
DVD 6-channel playback .................................. 26
Convenient functions ....................................... 27
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
• Power mode
• Input selector settings
• Picture output
• Speaker ON/OFF
• Volume level
• BASS, TREBLE, INPUT level
• TONE ON/OFF
• LOUDNESS ON/OFF
• Broadcast band
• Frequency setting
• Preset stations
Operations
• Tuning mode
• ACTIVE EQ mode
• PRO LOGIC II mode
• DSP mode
• Left channel level
• Right channel level
• Center channel level
• Surround channel level
• Dimmer level
• MD/TAPE settings
• Listen mode setting
• SP SYSTEM
• Speaker settings
• Distance setting
• SUBWOOFER ON/OFF
• SW RE-MIX ON/OFF
• Input mode setting
• Midnight mode setting
•
Surround Back channel level
• Subwoofer level
• PANORAMA ON / OFF
• DIMENSION
• CENTER WIDTH
• LFE level
Basic remote control operations for other
components....................................................... 29
DVD player operation keys .................................. 29
Remote
Control
In case of difficulty.......................................... 30
Specifications .................................................. 32
Additional
Information
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Preparing the remote control
For the U.S.A.
FCC WARNING
Loading the batteries
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modification is made.
1 Remove the cover.
2 Insert the batteries.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not
installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
3 Close the cover.
1
2
– – Increase the separation between the equipment and this model.
– – Connect the equipment into an outlet on a circuit different from
that to which this model is connected.
– – Consult the dealer or an experienced radio / TV technician for
help.
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
Operation
For the U.S.A.
When the STANDBY indicator is lit, the power turns ON when you press
the POWER
press the key you want to operate.
key on the remote control. When the power comes ON,
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical.
Operating range
(Approx.)
Remote sensor
6 m
®
As an ENERGY STAR Partner, Kenwood
Corporation has determined that this
®
product meets the ENERGY STAR
POWER
guidelines for energy efficiency.This
product can save energy. Saving energy
reduces air pollution and lowers utility bills.
Infrared ray system
• When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
replace both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Special features
DSP surround modes
True home theater sound
The DSP (Digital Signal Processor) used for this model incorporates a
variety of high quality adjustable sound fields, like “ARENA”, “JAZZ
CLUB”, THEATER”, STADIUM” and “DISCO”. It is compatible with
almost any kind of program source.
This model incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
£
DVD 6-channel input (KRF-V5080D only)
Dolby Digital and Dolby Digital EX
If you own a DVD player equipped with 6-channel output, this model
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround sound
systems.
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides up
to 5.1 channels of independent digital audio for better sound quality and
more powerful presence than conventional Dolby Surround. As for Dolby
Digital EX, it creates six full-bandwidth output channels from the 5.1
channel sources. This is done using a matrix decoder that derives three
surround channels from the two in the original recording. For best result,
Dolby Digital EX should be used with movie soundtracks recorded with
Dolby Digital Surround EX.
ACTIVE EQ
ACTIVE EQ mode will produce a more dynamic sound quality in any
condition. You can enjoy a more impressive sound effect when ACTIVE
EQ is turned on.
Dolby PRO LOGIC IIx and Dolby PRO LOGIC II
DOLBY PRO LOGIC II, whilst totally compatible with its predecessor
PRO LOGIC, provides greater advantages in surround sound. It allows
user to enjoy the conventional stereo or Dolby Surround with a convinc-
ing “5.1 like” presentation. PRO LOGIC II offers special features for
controlling the overall spatial, dimensionality and frontal sound field
imaging. PRO LOGIC II produces an impressive surround sound from
Universal IR (InfraRed) remote control
In addition to the basic receiver, the remote control supplied with this
model can also operate KENWOOD DVD player. Just follow the simple
setup procedure.
video software marked
and three-dimensional space
from music CD. When listening to music, you will be able to enjoy the
experience of sheer STEREO surround sound.
DOLBY PRO LOGIC IIx enhanced DOLBY PRO LOGICII’s features.
It creates 6.1 channel and 7.1 channelsurround sound from stereo or 5.1
channel signals. This feature provides you an astonishing ambience
effect which makes you feel you are surrounded by natural sound.
Especially 7.1 channel surround sound can produce real back sound from
Surround Back speakers.
DTS and DTS-ES
DTS (Digital Theater System) is a 5.1 channel digital audio format that
provides five full-spectrum channels and one low-frequency (subwoofer)
channel for unprecedented clarity, optimum channel separation and a
(wide) dynamic range.
DTS-ES (Extended Surround) presents 6.1 channels surround system
with additional Surround back channel which evolved from the conven-
tional 5.1 channels surround system. DTS-ES format that was recorded
in DVD, CD or LD comprises of two modes. DTS-ES Discrete 6.1
produces the discrete surround back which is completely independent
and DTS-ES Matrix 6.1 produces the surround back which synthesized
within the left and right surround channels using matrix technology. DTS-
ES has perfect compatibility with the conventional 5.1 channels surround
system. 6.1 channels surround with an additional surround back pre-
sents a more natural presence and surround effects by increasing the
impression of the sound image from back.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
Neo:6
Neo:6 is a new technology which was developed by DTS. It can produce
high grade 6 channels surround with an astonishing fidelity from 2
channels content. Neo:6 has 2 modes, “CINEMA” mode is for movie
playback and “MUSIC” mode is for music playback.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
Main Unit
Frequency display,
Input display,
Preset channel display,
Surround mode display
AUTO DETECT indicator
AUTO indicator
DIGITAL indicator
DSP MODE
indicator
Speaker indicator
6CH INPUT indicator
(KRF-V5080D only)
DTS indicator
Band indicators
CLIP indicator
MUTE indicator
DISCRETE 6.1
indicator
LOUDNESS indicator
TONE indicator
DOLBY DIGITAL
indicator
MATRIX 6.1
indicator
Input channel indicators
TUNED indicator
ST. indicator
NEO:6
indicator
PRO LOGIC
indicator
Display
VOLUME CONTROL
POWER
STANDBY
STANDBY
ON/STANDBY
ON/STANDBY
SPEAKERS ON/OFF
DIMMER
LISTEN MODE
DOWN
UP
ACTIVE EQ
DTS DOLBY DIGITAL
MULTI CONTROL
INPUT SELECTOR
POWER
SOUND
SETUP
MUTE
ON
OFF
ACTIVE EQ INPUT MODE
BAND
AUTO
MEMORY
PHONES
For VR-806
1 POWER ON/OFF key
(For KRF-V5080D)
Use to turn the main power ON/OFF.
2 ON/STANDBY key
(For KRF-V5080D)
Use to switch the power ON/STANDBY when
the POWER is turned ON.
STANDBY indicator
2 POWER ON/STANDBY key
(For VR-806)
Use to turn the power ON/STANDBY.
STANDBY indicator
3 DIMMER key
Use to select the REC MODE.
Use to adjust the brightness of the display.
¶
4 LISTEN MODE key
Use to select the listening mode.
^
5 Surround LED (light-emitting diode)
! SPEAKERS ON/OFF key
Use to turn the speakers ON/OFF.
@ ACTIVE EQ key
Use to select ACTIVE EQ setting.
# INPUT MODE key
Use to switch between full auto, digital and
analog inputs.
$ BAND key
Use to select the broadcast band.
% AUTO key
Use to change “TAPE” indication to “MD”.
*
Use to select the auto tuning mode.
^ MEMORY key
Use to store radio stations in the preset
memory.
& SETUP key
Use to select the speakers' settings etc.
* MUTE key
*
)
8
indicators
ACTIVE EQ mode LED indicator
)
Lights when this model is in the ACTIVE EQ
^
mode.
DTS mode LED indicator
∞
Lights when this model is in the DTS mode.
DOLBY DIGITAL EX mode LED indicator
∞
Lights when this model is in the Dolby
Digital EX mode.
¡
^
)
6 SOUND key
§
Use to adjust the sound quality and the
¡
™
ambience effects.
7 MULTI CONTROL knob
Use to control a variety of settings.
8 INPUT SELECTOR knob
Use to select the input sources.
9 VOLUME CONTROL knob
0 PHONES jack
^
*
^
∞
(
)
)
Use to temporarily mute the sound.
Use for headphone listening.
Standby mode
CAUTION
While the standby indicator is lit, a small amount of power is supplied to
the system to back-up the memory. This is called standby mode. Under
the condition, the system can be turned ON by the remote control unit.
The power in this equipment will not be completely cut off from the AC
wall outlet when the main switch is turned OFF.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
Remote control unit RC-R0626 (for VR-806) and RC-R0625 (for KRF-V5080D)
POWER
1
2
5
3
6
9
DVD
4
POWER
7
0
8
RECEIVER
+10
DOWN-PAGE-UP
LOUDNESS
RETURN
TOP MENU
MENU
OSD
SETUP
SOUND
LISTEN MODE
P.CALL
P.CALL
MULTI CONTROL
BAND
ENTER
TUNING
A/B+100 AUTO
BASS BOOST DISC SKIP
DVD
MD/TAPE
TONE
DVD/6CH
AUX
CD/DVD
TUNER
(For RC-R0625 only)
DVD
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
If the name of a function is different on
this model and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
VOLUME
MUTE
1 Numeric keys
™
7 A/B keys
Use to return to the operation of this model.
% -PAGE-UP key
Use to operate the DVD component.
^ TOP MENU key
Use to operate the DVD component.
& RETURN key
If TAPE is selected as the input source, this is
A and B deck of a double cassette deck.
+100 key4/¢keys
If CD or MD is selected as the input source,
these keys function as numeric keys. If tuner
is selected as the input source, these keys
are used to call up station presents.
2 DOWN-PAGE-key
Use to switch the DVD component.
LOUDNESS key
Use to switch the status of LOUDNESS.
3 MENU key
Use to operate the DVD component.
SETUP key
Use to select the disc number with the multi-
CD player.
DISC SKIP key
Use to operate the DVD component.
If CD is selected as the input source, this key
functions as the multi-CD player disc skip
key.
LISTEN MODE key
Use to select the listening mode.
* ENTER key
∞
^
)
Use to operate other components.
2 key
8 BASS BOOST key
(
^
Use to select the maximum adjustment
setting for the low frequency range.
Use to operate other components.
( BAND key
Use to select the speakers’ settings etc.
4 OSD (On Screen Display) key
Use to operate the DVD component.
¡
9 Input Selector keys [DVD or DVD/6CH (for
RC-R0625 only), AUX, CD/DVD, TUNER,
Use to select the broadcast band.
6 key
SOUND key
§
MD/TAPE, VIDEO 1, VIDEO 2]
Use to select the input sources.
4DVD ¢keys
*
If CD is selected as the input source, this keys
function as the play/pause key.
Use to adjust the sound quality and ambience
effects.
If MD or TAPE is selected as the input source,
this key functions as the play key.
5 MULTI CONTROL %/fi keys
Use to control a variety of settings.
Use to operate other components.
P.CALL4/¢ keys
^
™
When in DVD player operations, these keys
function as skip keys.
) 8 key
0 DISC SEL. key 8 key
Use to operate other components.
¡ AUTO key
Use to operate other components.
If tuner is selected as the input source, these
keys function as preset channel call keys.
4/¢keys
ACTIVE EQ key
)
)
Use to change “TAPE” indication to “MD”.
*
Use to select ACTIVE EQ setting.
! MUTE key 6 key
Use to select the auto tuning mode.
¡
If CD or MD is selected as the input source,
these keys function as skip keys.
Use to temporarity mute the sound.
7 key
@ POWER key
Use to turn this model on and off.
# DVD POWER key
Use to turn on the DVD equipment.
$ RECEIVER key
^
6 TUNING4/¢keys
¡
Use to operate the tuner or selected
component.
If CD, MD or TAPE is selected as the input
source, this key functions as the stop key.
™ TONE key
(
If CD, MD or TAPE is selected as the input
source, these keys function as search keys.
Use to switch the status of TONE control.
£ VOLUME keys
(
Use to adjust this model’s volume.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Make connections as shown in the following pages.
When connecting the related system components, be
sure to refer to the instruction manuals supplied with
the components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
Input mode settings
CD/DVD, VIDEO2, DVD (VR-806) and DVD/6CH(KRF-V5080D) inputs
each include jacks for digital audio input and analog audio input.
After completing connections and turning on this model, follow the
steps below.
LISTEN MODE
INPUT SELECTOR
Notes
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or there will be noise
interference.
2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connection
cords without disconnecting the power cord can cause malfunctions
and may damage the unit.
INPUT MODE
3. Do not connect power cords from components whose power
consumption is larger than what is indicated on the AC outlet at the
rear of this unit.
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2,
DVD (VR-806 only), DVD/6CH (KRF-V5080D only).
Analog connections
2 Press the INPUT MODE key.
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an “analog” form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs at each end, red for the right channel and white for the left
channel. These cables are usually packed together with the source unit,
or are available at your local electronics retailer.
Each press switches the setting as follows:
In DTS play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
In CD/DVD, VIDEO2, DVD(VR-806 only), DVD/6CH(KRF-V5080D
only) play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
3 6CH INPT (DVD/6CH input) (KRF-V5080D only)
4 ANALOG (analog input)
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the
microcomputer by referring to “In case of difficulty”.
º
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD
player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto detect:
In “F-AUTO” (full auto) mode (AUTO DETECT and DIGITAL
indicators light up), this model detects the digital or analog input
signals automatically. Priority is given to digital signal during input
mode selection. This model will select the input mode and listening
mode automatically during playback to match the type of input
signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial
factory setting is full auto.
To keep this model set to the currently selected listening mode, use
the INPUT MODE key to select “D-MANUAL” (digital manual).
However, even when this setting is selected, there may be cases
in which the listening mode is selected automatically to match a
Dolby Digital source signal depending on the combination of listening
mode and source digital.
In D-MANUAL mode, if the audio reproduction stops in the middle
due to change in the input signals etc, press the LISTEN MODE key.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting audio components
Shape of AC outlets
Australia
Other countries
To AC wall outlet
AUDIO
L
R
REC OUT PLAY IN REC OUT PLAY IN
MD / TAPE
VIDEO 1
AUX CD/DVD
IN
OUT
Video component )
OUT
IN
Cassette deck or MD
recorder
OUT
CD or DVD player
OUT
Other component
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting video components
AUDIO
VIDEO
DVD
IN
MONITOR
OUT
VIDEO 2
IN
REC OUT PLAY IN PLAY IN
VIDEO 1 VIDEO 2
VIDEO 1
IN
VIDEO 1
OUT
Video
IN
Monitor TV
Video input and output
(Yellow RCA pin cords)
Video deck
IN
IN
OUT
Audio inputs
and outputs
OUT
Video output
(Yellow RCA pin cords)
DVD player or LD player
Video OUT
Audio OUT
A video component with digital audio outputs should be connected to the VIDEO 2 jacks.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting video components (COMPONENT VIDEO) (Except for the Australia)
If you have connected this model to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEO
jacks.
COMPONENT VIDEO
VIDEO 2 IN
AUDIO
Y
Y
CB
DVD IN
CR
CB
CR
REC OUT PLAY IN REC OUT PLAY IN PLAY IN
MD / TAPE VIDEO 1 VIDEO 2
CD/DVD
MONITOR OUT
Monitor TV
Audio OUT
Video OUT
DVD player
DVD player or LD player
Audio OUT
Video OUT
When connecting the TV to the COMPONENT jacks, be sure to connect all the other components to the COMPONENT jacks.
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Digital connections
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD)
format digital signals.
If you have connected any digital components to this model, be sure to read the “Input mode settings” section carefully.
8
COAXIAL
VIDEO 2
OPTICAL
CD / DVD
DVD/6CH*
DIGITAL IN
*VR-806: DVD
OPTICAL DIGITAL OUT (AUDIO)
Optical fiber cable
CD or DVD player
COAXIAL DIGITAL OUT
(AUDIO)
Component with DTS,
Dolby Digital, or PCM
COAXIAL DIGITAL OUT
COAXIAL
DIGITAL
OUT
Connect the video signal and analog
audio signals to the VIDEO 2 jacks.
(See “Connecting video components”.)
0
(AUDIO)
RF digital
demodulator
(Commercially
available)
DOLBY DIGITAL RF
OUT (AUDIO)
PCM OUT
LD player
To connect an LD player with a DIGITAL RF OUT, connect the LD player to the RF digital demodulator (Commercially available).
Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of this model.
Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.)
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting a DVD player (6-channel input) (KRF-V5080D only)
If you have connected a DVD player to this model with digital connection, be sure to read the “Input mode settings” section carefully.
8
DVD/6CH INPUT
CENTER
COAXIAL
VIDEO 2
OPTICAL
CD/DVD
VIDEO
DVD
IN
MONITOR
OUT
VIDEO 2
IN
SUB
DVD/6CH
FRONT SURROUND
WOOFER
DIGITAL IN
VIDEO 1
IN
VIDEO 1
OUT
FRONT
OUT L/R
SUBWOOFER
OUT
SURROUND
OUT L/R
VIDEO OUT
(Yellow RCA
pin cord)
CENTER OUT
DVD player
COAXIAL
DIGITAL
OUT
(AUDIO)
CAUTION
Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard.
• Do not place any object impairing heat radiation onto the top of the unit.
• Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting the speakers
Surround Back Speakers
VR-806
Front Speakers
Left
Right
Surround Back Speaker
Right
Left
Center
Speaker
Power amplifier
Power amplifier
*VR-806:
SURR BACK
L
/SURR BACK
SURR BACK
L
FRONT
CENTER
/SURR BACK
SURR BACK
L*
+
VR-806 only
When using both
Surround Back Left
and Right speakers,
select “PRE OUT”
at speaker settings.
&
-
SURR BACK
R
SURR BACK
R
PRE OUT
R
L
C
PRE OUT
When connecting a single
Surround Back speaker
through a power amplifier to
PRE OUT jack, connect it as
above and select
RED
WHITE
GREEN
SPEAKERS (8
“SPEAKER” at speaker
settings.
&
VR-806
KRF-V5080D
SURROUND
BACK
SURROUND
SURROUND
SUB WOOFER
+
+
PRE OUT
-
-
R
L
BS
R
L
GRAY BLUE BROWN
SPEAKERS (8-16Ω)
GRAY
BLUE
SPEAKERS (8-16Ω)
Powered
sub woofer
When connecting a Surround
Back speaker to this terminal,
select “SPEAKER” at speaker
Right
Left
Surround
Back Speaker
(VR-806 only)
Surround Speakers
(Be sure to connect both
surround speakers)
settings.
&
To make sure that each speaker has been connected properly, pay attention to the test tone from each speaker.
Refer to “4 Adjust the speaker volume level ”.
&
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting the terminals
Connecting the antennas
AM loop antenna
1 Strip coating.
2 Push the lever
The supplied loop antenna is for use indoors. Place it as far as possible
from this model, TV set, speaker cords and power cord, and adjust the
direction for best reception.
AM antenna terminal connections
3 Insert the cord.
4 Return the lever.
1
Push lever.
2
Insert cord.
3
Release lever.
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be
unnatural with ambiguous acoustic imaging. Be sure to connect the
speakers correctly.
FM indoor antenna
The supplied indoor antenna is for temporary use only. For stable
signal reception we recommend using an outdoor antenna. Disconnect
the indoor antenna when you connect one outdoors.
Speaker impedance
FM antenna terminal connections
After confirming the speaker impedance indications printed on the
rear panel of this model, connect speakers with matching impedance
ratings. Using speakers with a rated impedance other than that
indicated on the rear panel of this model could result in malfunctions
or damage to the speakers or this model.
KRF-V5080D
VR-806
Insert the connector.
Speaker placement
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into
the room and connect it to the FM 75Ω terminal.
Center speaker
Subwoofer
Front
speaker
Listening
position
Surround
speaker
*Surround
Back Right
speaker
*Surround
Back Left
speaker
ANTENNA
FM
75Ω
AM
GND
*Optional in this model.
*Surround
Back speaker
Attach to the
stand
*For Surround Back speaker, you may place either two Surround
Back speakers (Surround Back Left speaker and Surround Back
Right speaker) for 7.1 channel surround sound system or one
Surround Back speaker for 6.1 channel surround sound system.
FM indoor antenna
Front speakers : Place to the front left and right of the listening
position. Front speakers are required for all surround modes.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Required for surround
playback.
VR-806
Surround speakers : Place to the direct left and right, or slightly
behind, the listening position at even heights, approximately 1 meter
above the ears of the listeners. These speakers recreate sound
motion and atmosphere. Required for surround playback.
Subwoofer : Reproduces powerful deep bass sounds.
Surround Back speaker/s : Place the speaker/s directly at the rear
of the listening position. The optimum position depends mainly on the
room condition.
KRF-V5080D
AM loop antenna
FM outdoor antenna
Use an antenna
adapter
(Commercially
available)
• Although the ideal surround system consists of all the speakers
listed above, if you don't have a center speaker or a subwoofer, you
can divide those signals between the available speakers in the
speaker settings steps to obtain the best possible surround
reproduction from the speakers you have available.
^
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
Speaker settings
To enable you to obtain optimum enjoyment from this model’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back speakers) as described below.
2 Use the MULTI CONTROL CONTROL knob or MULTI CONTROL
%/fikeys to select the speaker system setting.
POWER ON/STANDBY
(KRF-V5080D)
ON/STANDBY
MULTI CONTROL
1 CUSTOM
: For general speakers.
(VR-806)
2 FULL RANGE : For selected KENWOOD speaker - for example,
KS-207HT, KS-207EX, KS-208HT.
3 2WAY 2SPKR : For selected KENWOOD speaker – for
example, KS-307HT, KS-308HT, KS-308EX.
4 2WAY 3SPKR : For selected KENWOOD speaker – for
example, KS-707EX.
POWER ON/OFF
SETUP
• The selection of 2WAY 2SPKR or 2WAY 3SPKR should only be
used with 6 channels speaker system setting.
• When the setting 2WAY 2SPKR or 2WAY 3SPKR is selected, the
procedure skips to step 4.
(KRF-V5080D)
POWER
3 For general speaker setting, use the MULTI CONTROL knob or
MULTI CONTROL %/fikeys to select CUSTOM and press the
SETUP key again.
SETUP
MULTI
CONTROL
• The Subwoofer setting indication “SUBW ON” appears.
4 Use the MULTI CONTROL knob or MULTI CONTROL %/fi
keys to select the appropriate Subwoofer setting.
1Turn on the power to this model by pressing POWER ON/
STANDBY (for VR-806) or POWER ON/OFF and ON/
1 SUBW ON : Subwoofer setting mode to this model is ON.
2 SUBW OFF : Subwoofer setting mode to this model is OFF.
STANDBY (for KRF-V5080D) or POWER
key.
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the front speakers
are automatically set to “FRNT LRG” and the procedure skips to
step 7.
Before step 7, press the SETUP key to accept the setting.
• When Subwoofer output sound is required, select “FRNT NML”.
2Press the SETUP key to enter the SETUP mode and use the
MULTI CONTROL CONTROL knob or MULTI CONTROL
CONTROL %/ fikeys for the following displays.
1 SP SETUP
2 TESTTONE
3 DISTANCE
4 LFE LVL
5 EXIT
5 Press the SETUP key to accept the setting.
• The Front speakers setting indication “FRNT LRG” appears.
The flow of the SETUP is as follows;
6 Use the MULTI CONTROL knob or MULTI CONTROL %/fi
keys to select the appropriate Front speakers setting.
SP SETUP
SP System
TESTTONE
DISTANCE
LFE LEVEL
EXIT
1 FRNT LRG (large)
: Large Front speakers are connected to
this model.
Front Left
Center
AUTO MANUAL
2 FRNT NML (normal) : Average size Front speakers are
Custom
Full Range
L
L
connected to this model.
C
R
Front Right
C
2Way 2Speaker
2Way 3Speaker
• For “FRNT LRG” selection, no sound will be heard from subwoofer
speaker even when it is set to ON. However, if you select “SW
RE-MIX ON” when subwoofer is selected, you will be able to
hear sound from the subwoofer.
RS
RB
LB
LS
SW
Surround Right
Surround Back Right
Surround Back Left
Surround Left
R
Subwoofer
Front
RS
RB
LB
LS
SW
When in STEREO mode, the sound goes directly to front speaker.
Center
Surround
Surround Back
7 Press the SETUP key to accept the setting.
• The Center speaker setting indication “CNTR NML” appears.
Subwoofer
Subwoofer Re-mix
8 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys
to select the appropriate Center speaker setting.
(VR-806 only)
If you have selected “LRG” as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
connected to this model.
2 CNTR LRG (large) : A large Center speaker is connected to
this model.
• If you have selected “SPEAKER” as the Surround Back setting,“RB”/
”Surround Back Right ” and “LB” / “Surround Back Left ” are not
appeared but “BS” / “Surround Back” is appeared on the display.
3 CNTR OFF
: Center speaker setting mode to this
model is OFF.
3Select a speaker system.
1 Select SP SETUP and press the SETUP key again so that the
speaker system indication “SP SYSTEM” scrolls across the
display.
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
$ Use the MULTI CONTROL knob or MULTI CONTROL %/fi
If you have selected “NML” as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
connected to this model.
keys to select the appropriate Subwoofer re-mix setting.
1 RMX ON : Subwoofer re-mix set mode to this model is ON.
2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.
2 CNTR OFF
: Center speaker setting mode to this
model is OFF.
% Press the SETUP key to accept the setting.
9 Press the SETUP key again to accept the setting.
•The surround speaker setting indication “SURR NML” appears.
4Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
•In step 4 and 5, indications appear only for the selected channels
of the speakers that require adjusting.
0 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround speaker setting.
If you have selected “LRG” as the Center speaker setting,
1 SURR NML (normal) : Average size Surround speakers are
connected to this model.
1 Press the SETUP key to begin TEST TONE.
• This model enters the speaker volume level adjustment mode.
2 SURR LRG (large) : Large Surround speakers are connected
to this model.
: Surround speaker setting mode to this
model is OFF.
The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or MULTI CONTROL %/fi keys.
3 SURR OFF
1 AUTO
2 MANUAL
If you have selected other than “LRG” as the Center speaker
setting,
1 SURR NML (normal): Average size Surround speakers are
connected to this model.
2 Press the SETUP key again to select either AUTO or MANUAL.
2 SURR OFF
: Surround speaker setting mode to this
model is OFF.
Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to adjust the volume level of the test tone output from the
speaker channel to be adjusted.
• When the setting “SURR OFF” is selected, the procedure skips
to step #.
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
! Press the SETUP key to accept the setting.
• The Surround Back speaker setting indication “BS” appears.
@ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround Bback speaker setting.
If you have selected “LRG” as the surround speaker setting,
1 BS NML (normal : Average size Surround back speakers are
connected to this model.
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
2 BS LRG (large)
: Large Surround Back speaker is
connected to this model.
changed.
§
• If any of the speaker is set as OFF during SP SET UP, the TEST
TONE adjustment for the speaker will be skipped.
3 BS OFF
: Surround Back speaker setting mode to
this model is OFF.
(VR-806 only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared.
3 Press the SETUP key.
• The test tone is turned off. This model enters the mode for
If you have selected “NML” as the Surround speaker setting,
1 BS NML (normal) : Average size Surround Back speakers are
connected to this model.
inputting the distance to the speakers.
2 BS OFF
: Surround Back speaker setting mode to
4 For MANUAL selection, press the SETUP key each time to
this model is OFF.
select the speaker channel.
(VR-806 only)
5Input the distance to the speakers.
If you have selected “LRG” or “NML” as the surround back
speaker setting,(VR-806 only)
1 Select the DISTANCE from the set up displays and press the
1 SPEAKER : Surround Back signal will be output from
SURROUND BACK speaker terminal, and SURR
BACK L/ SURR BACK PRE OUT terminal as
monaural.
SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
2 PRE OUT : Surround Back signals will be output from SURR
BACK L/ SURR BACK and SURR BACK R PREOUT
terminals as stereo.
Jot down the distance to each of the speakers.
Distance to Front Left speaker (L)
: ____ feet (meters)
: ____ feet (meters)
Distance to Center speaker (C)
Distance to Front Right speaker (R) : ____ feet (meters)
Distance to Surround Right (RS) : ____ feet (meters)
Distance to Surround Back Right (RB) : ____ feet (meters)
Distance to Surround Back (BS) : ____ feet (meters)
Distance to Surround Back Left (LB) : ____ feet (meters)
# Press the SETUP key again to accept the setting.
• The subwoofer re-mix setting indication “SW RE-MIX” scrolls
across the display.
Distance to Surround Left (LS)
Distance to Subwoofer (SW)
: ____ feet (meters)
: ____ feet (meters)
(VR-806 only)
• If subwoofer is turned OFF, subwoofer re-mix setting is not
visible.
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared.
Continued to next page
EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
Normal playback
3 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys
to select the distance to the front speakers.
Preparing for playback
Some preparatory steps are needed before starting playback.
POWER ON/STANDBY
SPEAKERS
ON/OFF
(KRF-V5080D)
ON/STANDBY
Indication in feet Indication in meters
(VR-806)
• The allowable setting range is 1 to 30 feet (0.3m to 9.0m),
adjustable in 1 foot (0.3m) increments.
4 Press the SETUP key to accept the settings.
5 Repeat steps 3 and 4 to input the distance for each of the
speakers.
POWER
AUTO
INPUT SELECTOR
6Adjust the LFE (low freguency effects) level.
ON/OFF
(KRF-V5080D)
1 Select the LFE LEVEL from the set up displays and press the
SETUP key again.
Turning on this model
2 Use the MULUTI CONTROL Knob or MULTI CONTROL %/fi
keys to adjust the LFE LEVEL.
1 Turn on the power to the related components.
2 Turn on the power to this model by pressing POWER ON/
STANDBY (VR-806) or POWER ON/OFF and ON/STANDBY
(KRF-V5080D) key.
• The LFE LEVEL can be adjusted from odB to -10dB in 1dB step
decrements.
Selecting the input mode
3 Press the SETUP key to accept the setting.
If you have selected a component connected to the CD/DVD, VIDEO2,
DVD (VR-806) or DVD/6CH (KRF-V5080D) jacks, make sure that the
input mode setting is correct for the type of audio signal to be used.
8
4 Setup is complete when the EXIT indication appears.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the
source to “MD”, follow the steps below:
5 Press the SETUP key to exit the SETUP mode.
1 Use the INPUT SELECTOR knob to select “TAPE”.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
2 Hold down the AUTO key for more than 2 seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat procedure 2.
Setting the speaker status
1 Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
The speaker indicator lights up.
• You can store a separate input level for each input source.
2 Press the SOUND key repeatedly until the “INPUT” indication
appears.
Press the SPEAKERS ON/OFF key to switch the speaker on or off.
3 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to
adjust the input level.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
EN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal playback
Listening to a source component
Adjusting the sound
SPEAKERS ON/OFF
ACTIVE EQ
VOLUME CONTROL
VOLUME CONTROL
INPUT SELECTOR
PHONES
MULTI CONTROL MUTE
LOUDNESS
MULTI
CONTROL
ACTIVE EQ
Input
Selector
BASS BOOST
MUTE
TONE
VOLUME
VOLUME
Adjusting the Tone (remote control only)
Use the INPUT SELECTOR knob or keys to select the source
you want to listen to.
1
You can adjust the sound quality when this model is in the PCM stereo
and analog stereo mode.
The input sources change as shown below:
1 Press the TONE key to select the TONE mode.
1 “TUNER”
2 “CD/DVD”
3 “TAPE” or “MD”
4 “VIDEO1”
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to
select TONE ON/OFF.
5 “VIDEO2”
6 “DVD/6CH” (VR-806 : “DVD”)
7 “AUX”
Start playback from the selected source.
2
3
3 When in TONE ON selection, press the TONE key for the following
displays.
Use the VOLUME CONTROL knob or VOLUME keys to adjust
the volume.
BASS : Select this to adjust the low frequency range.
TREB : Select this to adjust the high frequency range.
4 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to
adjust the sound quality.
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
Once-touch low frequency emphasis (Bass Boost)
(remote control only)
You can adjust the sound quality when this model is in the PCM stereo
and analog stereo modes.
Press the BASS BOOST key.
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
• TONE will automatically be turned ON.
• This key does not function when this model is in the sound quality
or ambience effects adjustment mode.
Switching back to the previous setting
Press the BASS BOOST key again.
£~•
EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal playback
Recording
Recording audio (analog sources)
Adjusting the Loudness mode (remote control only)
You can adjust the Loudness function which controls the low volume
settings to maintain the music’s richness. The adjustment can be made
when this model is in the PCM stereo and analog stereo mode.
Press the LOUDNESS key to turn the Loudness setting ON.
To cancel
Press the LOUDNESS key again so that the “LOUDNESS” indicator
goes off.
INPUT SELECTOR
Muting the sound
Recording a music source
The MUTE key lets you mute the sound of the speakers.
1 Use the INPUT SELECTOR knob to select the source (other than
“MD/TAPE”) you want to record.
Press the MUTE key.
2 Set the MD or TAPE recorder to record.
3 Start playback, then start recording.
To cancel
Press the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
Recording video
1 Use the INPUT SELECTOR knob to select the video source (other
than “VIDEO1”) you want to record.
ACTIVE EQ mode
You can enjoy a more impressive sound effect when ACTIVE EQ is
turned ON during Dolby Digital and DTS playback and, when in PCM and
analog stereo mode.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC mode to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due to
Press the ACTIVE EQ key for the following selections;
the copy guard condition.
º
1 ACTIVE EQ MUSIC : Effective when listening to music.
(The ACTIVE EQ LED indicator lights up.)
2 ACTIVE EQ CINEMA : Effective when watching a movie.
(The ACTIVE EQ LED indicator lights up.)
Recording audio (digital sources)
3 ACTIVE EQ TV
: Effective when watching TV.
(The ACTIVE EQ LED indicator lights up.)
: The ACTIVE EQ function is turned OFF.
(The ACTIVE EQ LED indicator goes off.)
4 ACTIVE EQ OFF
Switch on the REC mode to record a digital input source.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A-REC
mode, the audio input source may be interrupted momentarily.
• ACTIVE EQ function will not be available when REC MODE, AUTO
TUNING or PRESET MEMORY is ON and during 96kHz LPCM
playback.
Recording music in A-REC or M-REC mode
Listening with headphones
DIMMER
1 Press the SPEAKERS ON/OFF key so that the speaker indicator
goes off.
Make sure the SP indicator is turned OFF.
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo playback.
INPUT SELECTOR
2 Connect headphones to the PHONES jack.
1 Use the INPUT SELECTOR knob to select the source (CD/DVD,
DVD/6CH (KRF-V5080D), DVD (VR-806) or VIDEO2) you want to
record.
PHONES
2 Set the MD or TAPE recorder to record.
3 Use the VOLUME CONTROL knob or VOLUME keys to adjust the
volume.
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Listening to radio broadcasts
This model can store up to 40 stations in the memory and recall them by
one-touch operation.
3 Press and hold the DIMMER key for more than 2 seconds to select
the A-REC or M-REC mode during digital input.
1 Rec mode off : The digital input record mode is switched off.
2 A-REC mode : The digital input signals (DTS, Dolby Digital,
or PCM) are identified automatically and
converted into stereo signals that are ready
for recording.
3 M-REC mode : The input signal type at the moment this
mode is selected is held throughout this
mode.
Tuning radio stations
MULTI CONTROL
• When the M-REC mode is selected, the digital input signal is
converted to stereo signals (down-mix). But once the digital signal
is chaned to other signal, no signal is output.
When the A-REC mode is selected, the digital input signal is
converted to stereo signals even if the digital signal is changed.
BAND
AUTO
INPUT SELECTOR
For A-REC mode:
MULTI
CONTROL
TUNING1/¡
BAND
TUNER
AUTO
For M-REC mode:
1Use the INPUT SELECTOR knob or TUNER key to select the
tuner.
2Use the BAND key to select the desired broadcast band.
“AM” or “FM” indicator
appears in the display
Each press switches the band
as follows:
1 FM
2 AM
4 Start playback, then start recording.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
3Use the AUTO key to select the desired tuning method.
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
“AUTO” indicator lights up in the display.
• Normally, set to “AUTO” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4Use the MULTI CONTROL knob or MULTICONTROL %/
fikeys, or TUNING 1/ ¡keys to select the station.
“ST.” lights when a broadcast
is being received in stereo.
Frequency display
“TUNED” is displayed when a
station is received.
Auto tuning
: The next station is tuned automatically.
Manual tuning : Turn the knob (press the key) to select the desired
station.
EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
Presetting radio stations manually
Receiving preset stations in order (P.Call)
MEMORY
P.CALL
4/ ¢
TUNER
MULTI CONTROL
1Tune to the station you want to store.
2Press the MEMORY key while receiving the station.
1Press the TUNER key to select tuner as the source.
Blinks for 20 seconds
2Use the P.CALL 4¥¢keys to select the desired station.
• Each time you press the key, another preset station is received in
order.
Proceed to step 3 within 20 seconds.
(If more than 20 seconds elapse, press the MEMORY key again).
Pressing the P.CALL ¢ does the following:
3Use the MULTI CONTROL knob or MULTI CONTROL %/ fikeys
to select one of the station presets (1 – 40).
Pressing the P.CALL 4does the following:
4Press the MEMORY key again to confirm the setting.
Holding down the P.CALL ¢or 4key, lets you skip through
the presets, receiving each preset station at 0.5 second intervals.
• Repeat steps 1, 2, 3, and 4 to store as many stations as
necessary.
• If you store a station at a previously used preset, the previous station
will be replaced by the new one.
Receiving preset stations
Numeric keys
TUNER
1Press the TUNER key to select tuner as the source.
2Enter the number of the preset station you want to receive
(up to “40”).
Press the numeric keys in the following order:
For “15”, press ................................ 0, 5
For “20”, press ................................ 0, 0, )
• If you make a mistake entering a two digit number, press the +10
key repeatedly to return to the original display and start again.
EN
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
This model is equipped with listening modes that allow you to enjoy an enhanced sonic ambience with a variety of video
sources.
In order to obtain the optimum effect from the surround modes, make sure to input the proper speaker settings beforehand.
^
Surround modes
The below speaker placements are for 6.1 channel surround sound
The below speaker placements are for 5.1 channel surround sound
system which are;
• Dolby Digital EX
• DTS - ES
system which are;
• Dolby Digital
• Dolby Pro Logic II
• DTS
• Neo:6
• DSP
• DVD 6-channel (KRF-V5080D only)
TV / SCREEN
TV / SCREEN
SW
C
SW
C
R
R
L
L
LS
RS
LS
RS
BS
No Surround Back speaker
With Surround Back speaker
The below speaker placements are for 7.1 channel surround sound
system which is;
• Dolby Pro Logic IIx
L
Front Left speaker
SW Subwoofer
C
Center speaker
R
Front Right speaker
LS
RS
BS
LB
RB
Surround Left speaker
Surround Right speaker
Surround Back speaker
Surround Back Left speaker
Surround Back Right speaker
TV / SCREEN
SW
C
R
L
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro
Logic” and the double-D symbol are trademarks of Dolby Laboratories.
LS
RS
“DTS”, “DTS-ES Extended
Surround” and “Neo:6” are
trademarks of Digital Theater
Systems, Inc.
Note
LB
RB
LFE = Low Frequency Effects. This channel delivers separate non-
directional bass signals to the subwoofer for more dynamic deep
bass sound effects.
With Surround Back Left and Right speakers
EN
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
Dolby Digital
DTS-ES
The Dolby Digital surround format lets you enjoy up to 5.1 channels
of digital surround sound from Dolby Digital program sources (such
DTS-ES (Digital Theater System-Extended Surround) presents 6.1
channels surround system with additional Surround Back channel
which evolved from the conventional 5.1 channels surround system.
DTS-ES format that was recorded in DVD, CD or LD comprises of two
modes. DTS-ES Discrete 6.1 produces the discrete surround back
which is completely independent and DTS-ES Matrix 6.1 produces
the surround back which synthesised within the left and right surround
channels using matrix technology. DTS-ES has perfect compatibility
with the conventional 5.1 channels surround system. 6.1 channels
surround with an additional surround back presents a more natural
presence and surround effects by increasing the impression of the
sound image from back. Programs which are recorded using DTS-ES
technology consist of information flags which will be able to control
the Discrete and Matrix mode. Thus, it can automatically select the
best matched mode.
as Laserdisc or DVD software marked
previous Dolby surround, Dolby Digital provides even better sound
quality, greater spatial accuracy, and improved dynamic range.
). Compared with
Although a full set of speakers (front left, right, and center, surround
left and right, and a subwoofer) is required for true 5.1 channel Dolby
Digital surround sound, this model lets you enjoy Dolby Digital (and
Dolby Surround) program sources, even if you connect only the front
speakers.
Dolby Digital EX
Dolby Digital EX is an extension of Dolby Digital technology, Dolby
Digital EX creates six full-bandwidth output channels from 6.1-
channel sources. This is done using a matrix decoder that derives
three surround channels from the two in the original recording.
This is achieved by using three different surround signals, surround
left, surround right, and surround back, each driving its own array of
speakers. Think of it as adding a center channel for the rear speakers,
which give more diffuse and natural surround effect, even if you
wanted the ability to completely encircle the audience with sound,
positioning sound effects exactly where they would be heard in real
life. For best results, Dolby Digital EX should be used with movie
soundtracks recorded with Dolby Digital Surround EX which contain
a digital flag that will automatically activate this feature. However, for
titles released prior to late 2001, this feature has to be activated
manually.
NEO:6
Neo:6 is a new technology which was developed by DTS. It can
produce high grade 6 channels surround with an astonishing fidelity
from 2 channels content. Neo:6 has 2 modes, “CINEMA” mode is for
movie playback and “MUSIC” mode is for music playback.
DTS has a “.1” or LFE channel.
The indication “LFE” appears in the display when a signal is being
input for this channel.
£
DTS
The DTS multi-channel audio format is available on CD, LD and DVD
software. DTS is a strictly digital format and cannot be decoded inside
most CD, LD or DVD players. For this reason, if you attempt to listen
to DTS encoded software through the analog output of your new CD,
LD or DVD player, you will experience digital noise in most cases. This
noise can be quite loud if the analog output is connected directly to
a high power amplification system. Proper measures for playing the
digital output as described below should be taken to avoid this
situation. To enjoy DTS Digital Surround playback, an external 5.1
channel DTS Digital Surround decoder system or an amplifier with a
built-in DTS Digital Surround decoder must be connected to the
digital output (S/P DIF, AES/EBU or TosLink) of a CD, LD or DVD
player.
Although a full set of speakers (front left, right, and center, surround
left and right, surround back and a subwoofer) is required for true 6.1
channel Dolby Digital Surround EX sound, this model lets you enjoy
Dolby Digital (and Dolby Surround) program sources, even if you
connect only the front speakers.
Although only Dolby Digital soundtracks incorporate a separate low
frequency channel, connecting a subwoofer will also improve deep
bass performance in the other surround modes.
Dolby Digital has a “.1” or LFE channel.
The indication “LFE” appears in the display when a signal is being
input for this channel.
£
All models are incorporated with the DTS decoder.
DTS has a “.1” or LFE channel.
The indication “LFE” appears in the display when a signal is being
Dolby PRO LOGIC IIx and Dolby PRO LOGIC II
Dolby Pro Logic II was designed specifically to provide a new sense
of spatiality, directionality and articulation of sounds from Dolby
Surround encoded sources (such as video and Laserdisc software
input for this channel.
£
marked
). This is achieved with an intelligent, built-in
DSP mode
feedback logic design, a matrix surround decoding and the decoding
of stereo, full bandwidth surround outputs.
The DSP mode lets you add the atmosphere of a live concert or hall
to almost any type of program source. These modes are particularly
effective when used with stereo program sources, like CD, television,
and FM radio. You might enjoy trying the ARENA, JAZZ CLUB,
THEATER, STADIUM or DISCO mode the next time you watch a
concert or sporting event!
DOLBY PRO LOGIC IIx enhanced DOLBY PRO LOGICII’s features.
It creates 6.1 channel and 7.1 channel surround sound from stereo or
5.1 channel signals. This feature provides you an astonishing ambience
effect which makes you feel you are surrounded by natural sound.
Especially 7.1 channel surround sound can produce real back sound
from Surround Back speakers.
What's DSP?
DSP stands for Digital Signal Processor.
The PRO LOGICIIx modes programmed into this model are “MOVIE”,
“MUSIC” and “GAME”. The PRO LOGIC II modes programmed into
this model are “MOVIE”, “MUSIC”, “GAME” and “PRO LOGIC”.
The “MOVIE” mode has preset characteristics to produce a calibrated,
high-level surround sound playback while the “MUSIC” mode has
user-adjustable characteristics to offer the three optional controls,
like “Dimension”, “Center Width” and “Panorama” modes to allow
optimization of the soundfields as desired. The “Dimension” control
allows the user to gradually adjust the soundfield either towards the
front or towards the rear; the “Center Width” control allows various
adjustment of the left-center-right speakers’ balance; the “Panorama”
mode extends the front stereo image to include the surround speakers
for an exciting “wraparound” effect with side wall imaging.
The “GAME” mode provides surrounded and exciting sound when
you enjoy game or TV. Especially in PRO LOGICIIx “GAME” mode,
base sound not only from Front and Center but also from Surround
channel is added to Subwoofer. This provides even more dynamic
surround effects.
The way a sound is heard in an actual environment depends on a
variety of different factors. One of the most important is reverberation
(the act of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP to
create reverberation, without spoiling the sound quality of the original
signal.
DVD 6-channel mode (KRF-V5080D only)
Using a DVD player or the like equipped with six (5.1) output channels
and this model, you can enjoy multi-channel encoded DVD source
material in all its splendor. Since the source signals are digital and
each channel is input independently, the resulting sound quality,
sense of spaciousness, and dynamic range are superb.
The indication “6CH INPUT” appears in the display when a signal is
being input for this channel.
EN
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
Surround play
When the DOLBY DIGITAL or DOLBY DIGITAL EX signal is input:
(The DOLBY DIGITAL or PRO LOGIC indicator lights up.)
The DTS compatible models can reproduce a CD, DVD, or LD carrying the
DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
1 DOLBY DIGITAL
: DOLBY DIGITAL surround.
(The DOLBY DIGITAL indicator lights up.)
the
mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC can be used when playing video, DVD, or LD
2 DOLBY DIGITAL EX : DOLBY DIGITAL EX surround.
(The DOLBY DIGITAL EX indicator lights
software bearing the
LISTEN MODE
mark.
up.)
3 PL IIx MOVIE
4 PL IIx MUSIC
5 PL IIx GAME
6 PL II MOVIE
7 PL II MUSIC
8 PL II GAME
9 PRO LOGIC
0 STEREO
: PRO LOGIC IIx surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC IIx surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC IIx surround GAME mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround GAME mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround PRO LOGIC mode.
(The PRO LOGIC indicator lights up.)
: Normal stereo playback.
INPUT MODE
INPUT SELECTOR
LISTEN MODE
Input
Selector
When you select DOLBY DIGITAL
“DOLBY DIGITAL” will scroll from right to left.
When the DTS or DTS-ES (matrix, discrete or bitstream) signal is
input:
Preparations
• Turn ON related components.
(The DTS LED indicator lights up.)
• Complete “Preparing for surround sound” (speaker settings).^
• Use the INPUT SELECTOR to select the component you wish to
play back with surround sound.
1 DTS-ES MATRIX 6.1 : DTS-ES MATRIX 6.1 channel surround
mode. (The DTS-ES and MATRIX 6.1
indicators light up.)
2 DTS-ES DISCRETE 6.1 : DTS-ES DISCRETE 6.1channel surround
mode.(The DTS-ES and DISCRETE 6.1
indicators light up.)
• Use the INPUT MODE key to select the input mode (analog or
digital) for the source you wish to playback.
8
• Noise will be produced when a DTS source is played by selecting the
analog input.
3 DTS
: DTS 5.1 ch surround mode
(The DTS indicators light up.)
4 DTS + NEO:6 CINEMA : DTS + NEO:6 surround CINEMA mode.
Start playing the video software.
1
2
(The DTS and NEO:6 indicator lights up.)
: Normal stereo playback
5 STEREO
Press the LISTEN MODE key to select the listening mode.
When the analog signal or the digital signal (except for DOLBY
DIGITAL or DTS signal) is input:
The listening mode settings are stored separately for each input. If the
input mode is set to full auto (“AUTO DETECT” lights), this model
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
1 PL IIx MOVIE :PRO LOGIC IIx surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
2 PL IIx MUSIC :PRO LOGIC IIx surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
Each press of the LISTEN MODE key switches the setting as
listed.
3 PL IIx GAME
4 PL II MOVIE
5 PL II MUSIC
6 PL II GAME
7 PRO LOGIC
:
PRO LOGIC II x surround GAME mode.
(The PRO LOGIC indicator lights up.)
The listening mode settings are different depending on the type
of input signal.
: PRO LOGIC II surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
Dolby Digital Surround EX compliant disc :
Dolby Digital Surround EX compliant disc contains the identification
signals. When you choose FULL AUTO during “Input mode
setting”(8), this amplifier detects the identification signals and
change the LISTEN mode to the DOLBY DIGITAL EX (Dolby Digital
Surround EX mode) automatically.
But sometimes we find some discs which are Dolby Digital Surround
EX compliant disc but it does not contain the identification signals.
If you find the notice like “Surround EX” on the label of disc or
package, you can choose DOLBY DIGITAL EX then you can enjoy
Dolby Digital Surround EX sound.
:
PRO LOGIC II surround GAME mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround PRO LOGIC mode.
(The PRO LOGIC indicator lights up.)
8 NEO:6 CINEMA : NEO:6 surround CINEMA mode.
(The NEO:6 indicator lights up.)
9 NEO:6 MUSIC : NEO:6 surround MUSIC mode.
(The NEO:6 indicator lights up.)
0 ARENA
: DSP Surround ARENA mode.
- JAZZ CLUB
: DSP Surround JAZZ CLUB mode.
Continued to next page
EN
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
= THEATER
~ STADIUM
! DISCO
: DSP Surround THEATER mode.
: DSP Surround STADIUM mode.
: DSP Surround DISCO mode.
: Normal stereo playback.
DVD 6-channel playback (KRF-V5080D only)
Using a DVD player or the like equipped with six (5.1) output channels and
this model, you can enjoy surround sound playback.
Connecting a DVD player which can decode the surround signal itself is
also acceptable.
@ STEREO
• Dolby Digital or DTS signal having more channels than the maximum
number of playback channels available using this model’s current
settings is input, downmixing is performed to match the number of
available channels.
Adjust the volume.
3
Notes
• Depending on the type of the signal or speaker setting, some
INPUT MODE
INPUT SELECTOR
listening modes cannot be selected.
• When playback is started, the sound may be cut or interrupted
before the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component.
DVD/6CH
Preparations
• Connect your DVD player to the DVD/6CH jacks of this model.
• Turn on all other components that will be used.
• Complete “Preparing for surround sound”.
^
Select “DVD/6CH” as the input source.
1
2
3
4
Select "6CH INPT" by pressing the INPUT MODE key.
Start playback of the DVD software.
Adjust the volume.
• It is not possible to adjust the volume level or sound quality (SETUP,
SOUND, LISTEN MODE, ACTIVE EQ and TONE keys will not be
functional) of the channels separately when this model is in the
6CH INPUT mode. Adjust the volume with the controls of the DVD
player.
For the powered subwoofer, you can adjust the volume of the
subwoofer using the subwoofer’s own volume control.
EN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
Convenient functions
DIMMER
Midnight mode (Dolby Digital and DTS mode only)
When watching movies at night, you might not be able to raise the
volume as loud as normal. Midnight mode compresses the dynamic
range of previously specified heavy sound passage of the Dolby Digital
and DTS sound track (like scenes with sudden increases in volume) to
minimize the difference in volume between the scenes with heavy
sound passage and scenes with normal sound passage. This makes it
easy to hear all of the sound track, even when listening at low volumes.
SOUND
1 Press the SOUND key repeatedly until “NIGHT” appears on the
display.
• This can be selected only if CD/DVD, DVD/6CH (KRF-V5080D), DVD
(VR-806) or VIDEO2 is selected as the source and the listen mode
is set to “DOLBY DIGITAL” or “DTS”.
MULTI CONTROL
MULTI
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
select the ON or OFF setting.
SOUND
CONTROL
• Some Dolby Digital or DTS software may not be compatible with the
Midnight mode.
Panorama mode (Pro Logic IIx and Pro Logic II Music mode
only)
Adjusting the sound
When listening to music, you will be able to enjoy the “wraparound”
sound effect when you adjust the panorama mode.
You can make further adjustments to the sound while listening to
playback in the surround mode.
1 Press the SOUND key repeatedly until “PANORAMA” appears on
the display.
1 Press the SOUND key until the desired item appears in the
display.
• The PANORAMA setting indication scrolls across the display.
“PANORAMA” will be scrolled from right to left.
Each time you press the button, the menu changes as follows:
Note that some items are not displayed depending on speaker
settings and listening modes.
1 C (Center speaker level adjustment)*
2 RS (Surround Right speaker level adjustment)*
3 RB (Surround Back Right speaker level adjustment)*
4 BS (Surround Back speaker level adjustment)* (VR-806 only)
5 LB (Surround Back Left speaker level adjustment)*
6 LS (Surround Left speaker level adjustment)*
7 SW (Subwoofer level adjustment)*
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
select PANORAMA ON or OFF.
1 ON : PANORAMA mode is ON.
2 OFF : PANORAMA mode is OFF.
8 INPUT (input level adjustment - analog mode only)
9 NIGHT (midnight mode ON/OFF - Dolby Digital and DTS
mode only)
*
0 PANORAMA (panorama mode ON/OFF)**
- DIMENSION (dimension adjustment)**
= CENTER WIDTH (center width adjustment)**
~ OFF
Dimension mode (Pro Logic IIx and Pro Logic II Music mode
only)
*The adjustment is only temporary for the current input selection.
The value will return automatically to the original setup value
when the power is turned on/off or when the input selection is
changed.
When listening to music with certain recordings, you will also be able to
achieve a suitable balance from all the speakers by adjusting the
dimension mode.
** Pro Logic IIx and Pro Logic II Music mode only.
(VR-806 only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared.
1 Press the SOUND key repeatedly until “DIMENSION” appears on
the display.
• The DIMENSION indication scrolls across the display.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
adjust the setting as desired.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
adjust the soundfield towards the rear or the front.
Continued to next page
EN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
Soundfield is adjusted towards the front.
96kHz LPCM playback
This model is compatible with the 96kHz LPCM playback. To play a 96kHz
DVD, set the listen mode to “STEREO”.
• In F-AUTO input mode, the listen mode will automatically be STEREO.
• When in D-MANUAL input mode (listen mode is not STEREO), “FS
96kHz” will appear in the display and no sound can be heard from the
speakers.
Soundfield is in neutral position.
Press the LISTEN MODE key (the listen mode changes to the STEREO
mode) to output sound from the speakers.
Soundfield is adjusted towards the rear.
Center Width mode (Pro Logic IIx and Pro Logic II Music mode
only)
Center Width adjustment allows you to enjoy an enhanced sound when
listening to music through center image from only center speaker, or left
and right speakers or various combinations adjustments.
1 Press the SOUND key repeatedly until “CENTER WIDTH” appears
on the display.
• The CENTER WIDTH indication scrolls across the display.
• When the center speaker is switched OFF, this mode will not be
effective.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
adjust the left-center-right output.
Center image will be heard from center speaker only.
Center image will be heard from left and right speakers only.
• When in other positions, center image from center speaker, left and
right speakers can be heard simultaneously with various
combinations.
Display dimmer adjustment
The dimmer function lets you select the brightness of this model's
display. You might find this useful if you darken your room to watch
movies or listen to music.
Each time you press the DIMMER key, the display brightness
changes among the three available settings. Select the brightness
level you find most pleasing.
EN
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic remote control operations for other components
DVD player operation keys
The remote control of this unit can control two groups of KENWOOD DVD players directly without using the remote control supplied with the DVD player.
Group-1 : DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900,
DV5700, DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,
DVF-3060, DVF-3060K, DV-705, DVF-R5070 ,DVF-3070, DVF-3080, DVF-N7080 and DVF-8100.
Group-2 : DV-4050, DV-303, DVF-R6030, DVF-K5020, DVF-5020, DVF-3020 and DVF-3030.
Depending on your KENWOOD DVD model, you need to set up your remote control as follows:
To set for Group-1 DVD players:
Press the numeric “1” key while pressing the “POWER ” key (not the DVD POWER key) on your remote control.
To set for Group-2 DVD players:
Press the numeric “2” key while pressing the “POWER ” key (not the DVD POWER key) on your remote control.
• If your DVD player is not listed in the list above, perform the set up for either Group-1 or Group-2. When the set up is successful, then your DVD
player falls into that particular group.
How to operate the DVD player with the remote control
1. Pressing the DVD POWER key for more than 2 seconds turns the DVD player on or off.
2. To carry out the functions of the DVD player, first press the DVD POWER key, then press each key for each operation as explained in the DVD
operation pages in the operating instructions. In this case, the DVD operation mode is retained for 15 seconds after pressing any of those DVD
operation buttons.
(To turn the receiver operation mode within 15 seconds, press the RECEIVER key.)
DVD player operation keys
You can perform these basic operations using the keys described below when connected to KENWOOD DVD player.
POWER
1
2
5
3
6
9
POWER
DVD POWER
DVD
4
RECEIVER
(Receiver mode)
Numeric keys
(Select tracks)
POWER
7
0
8
DOWN-PAGE-UP
(Page up or down)
RECEIVER
+10
OSD
DOWN-PAGE-UP
LOUDNESS
TOP MENU
RETURN
OSD (OSD menu)
TOP MENU
(Title)
MENU
MENU
SETUP
SOUND LISTEN MODE
RETURN
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
P.CALL
P.CALL
MULTI CONTROL
ENTER (Enter)
BAND
ENTER
TUNING
6 (3 Play)
A/B+100 AUTO
1 (Search)
8 (Pause)
BASS BOOST DISC SKIP
DVD
MD/TAPE
TONE
¡ (Search)
DVD/6CH
AUX
CD/DVD
TUNER
(For RC-R0625 only)
DVD
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
7 (Stop)
VOLUME
MUTE
EN
29
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
For the U.S.A. and Canada
Resetting the Microcomputer
Unplug the power cord from the wall outlet, then plug
it back in while holding down the POWER ON/STANDBY
key.
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If
this happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
For other countries
With the power cord plugged in, turn the POWER ON/
OFF key OFF. Then, while holding down the ON/STANDBY
key, press POWER ON/OFF key.
• Please note that resetting the microcomputer will clear the contents
of the memory and return the unit to the state it was in when it left
the factory.
Amplifier
Symptom
Remedy
Cause
No sound from the speakers.
• Connectthemproperlyreferringto“Connecting
• The speaker cords are disconnected.
the speakers”.
$
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
• Set the SPEAKERS switch to ON.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
)
*
• Turn the power off, eliminate the short-
circuiting, then turn on the power again.
The standby indicator blinks and sound is
not output.
• Speaker cords are short-circuited.
• Connect it properly referring to “Connecting
Sound is not output from one of the speakers.
• The speaker cord is disconnected.
• The speaker is not set up correctly.
the speakers”.
• Set it up properly referring to “Speaker
settings”.
$
^
• Connect it properly referring to “Connecting
the speakers”.
• Set it up properly referring to “Speaker
• The surround speaker cords and/or the center
speaker cord is disconnected.
• The speaker is not set up correctly.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very soft.
$
settings”.
^
• Select a surround mode.
• Adjust the speaker levels using the test tone.
&
• A surround mode has not been activated.
• The surround and/or center volume controls
are set to the minimum level.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
8
• There are many possible causes for this
problem, depending on the type of DVD player
used.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
• Press the INPUT MODE key to select to full
• The input mode is set to digital manual.
No sound is produced during playback from
a DVD player.
auto mode.
8
• Copy-guarded video software cannot be
recorded.
• The software is copy-guarded.
A video source cannot be recorded normally.
Tuner
Symptom
Cause
Remedy
Radio stations cannot be received.
• No antenna is connected.
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
%
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
¡
• Noise due to ignition of an automobile.
• Install the outdoor antenna away from the
road.
Interference.
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
EN
30
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
Remote control unit
Symptom
Remote control operation is not possible.
Cause
Remedy
• The remote control is set to a different
operation mode.
• Batteries are exhausted.
• Press the any of the Input Selector keys to
select the appropriate operation mode.
• Replace with new batteries.
• The remote control unit is too far away from
the main system, controlling angle is too
large, or there is an obstacle between the
receiver and the remote.
• Operate the remote control unit within the
controllable range.
• No tape or CD is placed in the source
component.
• Place the tape or CD in the source component
which you want to play.
• An attempt is made to play a tape which is
being recorded in the cassette deck.
• Wait for recording to complete.
• Press the DVD POWER key for more than 2
seconds to activate the operation mode for
the KENWOOD DVD player you want to control
• The remote control has not been set to the
operation mode for the KENWOOD DVD player
you wish to control.
before operation.
ª
EN
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution : Read this page carefully to ensure safe
operation.
Specifications
For the U.S.A and Canada
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level / impedance / wave length
AUDIO section
Rated power output during STEREO operation
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm 30 nm
Coaxial................................................................... 0.5 Vp-p / 75 Ω
100 watts per channel minimum RMS, both channels driven, at 8Ωfrom
40 Hz to 20 kHz with no more than 0.7% total harmonic distortion. (FTC)
Effective power output during SURROUND operation
FRONT (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel driven)
............................................................................... 100 W + 100 W
CENTER (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel driven)
.............................................................................................. 100 W
SURROUND (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel
driven) ................................................................... 100 W + 100 W
SURROUND BACK (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one
channel driven) ................................................................... 100 W
Total harmonic distortion ........................... 0.05% (1 kHz, 50 W, 8Ω)
Frequency response
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 Ω
COMPONENT VIDEO inputs/outputs (except for the Australia)
COMPONENT VIDEO (luminance signal) ............... 1 Vp-p/75 Ω
COMPONENT VIDEO (CB/CR-signal)............... 0.32 Vp-p/75 Ω
FM tuner section
Tuning frequency range................................. 87.5 MHz ~ 108.0 MHz
Usable sensitivity (MONO)
VR-806
CD/DVD ...................................... 20 Hz ~ 70 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
.................1.3 µV (75 Ω)/ 13.2 dBf (75 kHz DEV., SINAD 30 dB)
KRF-V5080D
CD/DVD, AUX, TAPE, VIDEO 1, VIDEO 2 .......................... 95 dB
Input sensitivity / impedance
CD/DVD ................................................................ 550 mV / 47 kΩ
Output level / impedance
TAPE REC ............................................................... 550 mV / 1 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
PRE OUT (SURROUND BACK) .............................. 1.5 V / 2.2 kΩ
Tone control
................... 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz DEV., SINAD 30 dB)
50dB quieting sensitivity
STEREO ..................................................... 28 µV (75 Ω)/ 40.2 dBf
Total harmonic distortion (1 kHz)
MONO.......................................................... 0.5% (71.2 dBf input)
STEREO ....................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz, 75 kHz DEV.)
MONO........................................................ 75 dB (71.2 dBf input)
STEREO ..................................................... 68 dB (71.2 dBf input)
Stereo separation (1 kHz) ........................................................... 40 dB
Selectivity ( 400 kHz) VR-806 .................................................... 70 dB
KRF-V5080D ........................................... 50 dB
BASS................................................................ 10 dB (at 100 Hz)
TREBLE ............................................................ 10 dB (at 10 kHz)
Loudness control
VOLUME at -30dB level ................................... +8 dB (at 100 Hz)
Frequency response .................... (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
For other countries
AUDIO section
AM tuner section
Rated power output during STEREO operation
Tuning frequency range
10 kHz step (VR-806) .................................. 530 kHz ~ 1,700 kHz
10 kHz step (KRF-V5080D) ............................. 530 kHz ~ 1,610 kHz
9 kHz step (KRF-V5080D) ............................... 531 kHz ~ 1,602 kHz
Usable sensitivity (30% mod., S/N 20dB) (VR-806)
........................................................................16 µV / (600 µV/m)
Usable sensitivity (KRF-V5080D) .............................16 µV / (600 µV/m)
Signal to noise ratio (30% mod. 1 mV input)........................... 50 dB
100 watts per channel minimum RMS, both channels driven, at 8Ωfrom
40 Hz to 20 kHz with no more than 0.7% total harmonic distortion. (FTC)
Effective power output during SURROUND operation
FRONT
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) ..... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) ...... 120 W + 120 W
CENTER
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) ........................100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) .........................120 W
SURROUND
GENERAL
Power consumption VR-806 ....................................................... 2.2 A
KRF-V5080D ............................................. 280W
AC outlet
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) ..... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) ...... 120 W + 120 W
Total harmonic distortion ........................... 0.05% (1 kHz, 50 W, 8Ω)
Frequency response
CD/DVD ...................................... 20 Hz ~ 70 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
CD/DVD, AUX, TAPE, VIDEO 1, VIDEO 2 .......................... 95 dB
Input sensitivity / impedance
CD/DVD ................................................................ 550 mV / 47 kΩ
DVD/6CH INPUT................................................. 550 mV / 15 kΩ
Output level / impedance
TAPE REC ............................................................... 550 mV / 1 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone control
SWITCHED
VR-806 ................................................ (total 150 W, 1.25 A max.)
KRF-V5080D ..................................................... (total 90 W max.)
Dimensions....................................................W : . 440 mm (17-5/16")
H : 143 mm
(5-5/8")
D : 303 mm (11-15/16")
Weight (Net)
VR-806 ................................................................... 7.7 kg (17.0 lb)
KRF-V5080D (for the Australia) .......................... 7.8 kg (17.2 lb)
KRF-V5080D (except for the Australia) ............. 8.8 kg (19.4 lb)
BASS................................................................ 10 dB (at 100 Hz)
TREBLE ............................................................ 10 dB (at 10 kHz)
Loudness control
VOLUME at -30dB level ................................... +8 dB (at 100 Hz)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model_____________________ Serial Number_____________________
EN
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|