Kenwood Stereo Amplifier B64 2562 00 00 User Manual

Troubleshooting Guide  
Controls  
What might appear to be a malfunction in your unit may just be the result of slight  
misoperation or miswiring. Before calling service, first check the following table for possible  
problems.  
9
KAC-6201  
KAC-5201  
KAC-5201  
KAC-6201  
0.5 0.3  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
10  
No sound.  
(No sound from one side.)  
• Input (or output) cables are  
disconnected.  
• Connect the input (or output)  
cables.  
1.0  
15  
20  
(W)  
6 7 89  
0
0
!
!
1234  
5
MIN  
INPUT  
SENSITIVITY(V)  
MAX  
• Protection circuit may be  
activated.  
• Volume is too high.  
• Check connections by referring  
to "Power indicator".  
• Replace the fuse and use lower  
volume.  
KAC-6201  
(Blown fuse.)  
25W or greater  
KAC-5201  
• The speaker cord is shorted.  
• After check the speaker cord and  
fixing the cause of the short,  
replace the fuse.  
KAC-6201  
KAC-5201  
Power indicator  
6 7 89  
POWER AMPLIFIER  
The output level is too  
small (or too large).  
The input sensitivity adjusting  
control is not set to the correct  
position.  
Adjust the control correctly  
referring to "Controls".  
Operations of the following control and switches  
are required in accordance with the center unit  
and speakers connected with this unit.  
• STEREO position  
The amplifier can be used as a stereo amplifier.  
6 RCA cable ground lead terminal  
When using an RCA cable with a ground lead  
attached, connect the ground lead to this terminal.  
INSTRUCTION MANUAL  
Power indicator  
When the power is turned on, the Power indicator  
lights.  
If the Power indicator does not light when the power  
is turned on, the protection function may be  
activated. Check whether there is any indication of  
trouble.  
放大器  
• L+R position (KAC-6201 only)  
The input left and right signals are combined  
before being amplified. Use this position when  
the unit is used for subwoofer speakers or the  
L+R (monaural) sound is required.  
The sound quality is bad.  
(The sound is distorted.)  
• The speakers wire are  
connected with wrong + / -  
polarity.  
• Connect them properly checking  
the + / - of the terminals and  
wires well.  
2CAUTION  
1 Fuse  
使用說明書  
25 A × 1 : KAC-6201  
15 A × 1 : KAC-5201  
Do not use this terminal for power source  
grounding. This unit will be damaged if the power  
source grounding wire is connected to this  
terminal.  
• A speaker wire is pinched by a  
screw in the car body.  
• Connect the speaker wire again  
so that it is not pinched by  
anything.  
NOTE  
• MONO (Lch) position  
If you can’t find the specified capacity fuse at your  
store etc., consult your Kenwood dealer.  
Amplifies the signal input from the left side only.  
Set to this position and make bridged  
connections to use as a high-power monaural  
amplifier. (The input right signal is not output.)  
The protection function is activated  
in the following situations:  
7 FILTER switch  
• The switches may be set  
improperly.  
• Set switches properly by  
referring to "System examples".  
These switches allow filtering of the speaker  
output signals.  
2 Battery terminal  
This unit is equipped with a protection function for  
protecting this unit and your speakers from various  
accidents or problems that can occur.  
When the protection function is triggered, the  
Power indicator goes off and the amplifier stops  
operating.  
3 Ground terminal  
• HPF (High Pass Filter) position (KAC-  
6201 only)  
Only frequencies of 150 Hz or higher are output.  
(Frequencies below 150 Hz are cut.)  
• LPF (Low Pass Filter) position  
Only frequencies of 80 Hz or lower are output.  
(Frequencies above 80 Hz are cut.)  
The Lch and Rch will be mixed before output  
even if the operation switch is set to STEREO.  
• OFF position  
The original sound without filtering is output.  
9 INPUT SENSITIVITY control  
Set this control according to the pre-output level of  
the center unit connected with this unit, or to the  
maximum power output of the genuine-accessory  
car stereo.  
4 Power control (REMOTE) terminal  
Specifications  
Specifications subject to change without notice.  
Audio Section ........................................................................KAC-6201 KAC-5201  
Max Power Output ..............................................................................................350 W × 1 250 W × 1  
Rated Power Output (4 )  
Normal (20 Hz – 20 kHz, 0.08 % THD)................................................................60 W × 2 40 W × 2  
Bridge (1 kHz, 0.8 % THD)................................................................................150 W × 1 120 W × 1  
Rated Power Output (2 )  
Normal (1 kHz, 0.8 % THD) ................................................................................75 W × 2 60 W × 2  
Frequency Response (+0, –1 dB) ..................................................................10 Hz – 45 kHz 5 Hz – 50 kHz  
Signal to Noise Ratio ..................................................................................................100 dB 100 dB  
Sensitivity (MAX) (rated output) ....................................................................................0.2 V 0.2 V  
Sensitivity (MIN) (rated output)......................................................................................5.0 V 5.0 V  
Input Impedance ..........................................................................................................10 k10 kΩ  
Low Pass Filter (12 dB/oct.)..........................................................................................80 Hz 80 Hz  
High Pass Filter (12 dB/oct.) (KAC-6201 only) ............................................................150 Hz  
5 SPEAKER OUTPUT terminals  
• Stereo Connections:  
When you wish to use the unit as a stereo  
amplifier, stereo connections are used.  
• Bridged Connections:  
When you wish to use the unit as a high-output  
monaural amplifier, bridged connections are  
used. (Make connections to the LEFT channel (+)  
and the RIGHT channel (–) SPEAKER OUTPUT  
terminals.)  
• When a speaker wire may be short-circuited.  
• When a speaker output contacts ground.  
• When the unit malfunctions and a DC signal is  
sent to the speaker output.  
• When the internal temperature is high and unit  
won’t operate.  
• When a ground wire of the center unit (cassette  
receiver, CD receiver, etc.) or this unit is not  
connected to a metal part serving as an electrical  
ground passing electricity to the battery's  
negative - terminal.  
Use the diagram on the right as a guide.  
NOTE  
For the pre-output level or the maximum power  
output, refer to the “Specifications” in the  
instruction manual of the center unit.  
0 LINE IN terminal  
8 OPERATION switch  
This switch allows selection of the amplification  
method of input signals.  
! Speaker level input terminals  
General....................................................................................KAC-6201 KAC-5201  
Operating Voltage (11 – 16 V allowable)......................................................................14.4 V 14.4 V  
Current Consumption (1 kHz, 10% THD) ......................................................................19 A 16 A  
Dimensions (W × H × D)[mm] ........................................................................228 × 59 × 228 228 × 59 × 160  
Dimensions (W × H × D)[inch]..........................................................................9 × 2-5/16 × 9 9 × 2-5/16 × 6-5/16  
Weight............................................................................................................2.8 kg (6.1 lbs) 2.1 kg (4.6 lbs)  
System examples  
Connection  
*Commercially available parts  
NOTE  
For safe installation, read "Installation procedure" before starting work.  
2-channel system  
RCA cable connection  
Speaker level input connection  
Left speaker  
L
L
CENTER  
UNIT  
Right speaker  
R
R
Genuine-accessory car stereo (No  
line output center unit etc.)  
CENTER UNIT (Cassette receiver,  
CD receiver, etc.)  
KAC-5201  
8
KAC-6201  
Speaker  
7
8
7
© B64-2562-00/00 (MV)  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
FILTER  
OFF  
FILTER  
OFF  
RCA cable*  
HPF  
LPF STEREO MONO(Lch)  
Car fuse box  
ACC  
Subwoofer system  
CENTER  
UNIT  
Left speaker  
Battery  
Wiring  
Safety precautions  
Accessories  
Right speaker  
Installation procedure  
1.Remove the ignition key and disconnect the  
negative - terminal of the battery to prevent  
short circuits.  
2.Set the unit according to the intended usage.  
3.Connect the input and output cables of the  
units.  
T
• If a buzzing noise is heard from the speakers  
H
6
!
F
IG  
R
External  
View  
Number of  
Items  
GND  
when the engine is running, connect a line noise  
L
L
Part name  
Subwoofer  
T
2WARNING  
SPEAKER LEVEL INPUT  
E
L
filter (optional) to each of the battery wire.  
• Do not allow the wire to directly contact the edge  
of the iron plate by using Grommets.  
R
R
To prevent injury or fire, take the following  
precautions:  
Terminal cover  
(Power terminal)  
1
4
• When extending the ignition, battery, or ground  
wires, make sure to use automotive-grade wires or  
other wires with a 3mm2 (AWG12) or more to  
prevent wire deterioration and damage to the wire  
coating.  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
• If the unit starts to emit smoke or strange smells,  
turn off the power immediately and consult your  
Kenwood dealer.  
• Do not touch the unit during use because the surface  
of the unit becomes hot and may cause burns if  
touched.  
KAC-5201  
8
KAC-6201  
• Connect the ground wire to a metal part of the  
car chassis that acts as an electrical ground  
passing electricity to the battery‘s negative -  
terminal. Do not turn the power on if the ground  
wire is not connected.  
• Be sure to install a protective fuse in the power  
cord near the battery. The protective fuse should  
be the same capacity as the unit’s fuse capacity  
or somewhat larger.  
• For the power cord and ground, use a vehicle  
type (fireproof) power wring cord with a current  
capacity greater than the unit’s fuse capacity.  
(Use a power wiring cord with a diameter of 3  
mm2 (AWG 12) or greater.)  
• When more than one power amplifier are going  
to be used, use a power supply wiring wire and  
protective fuse of greater current-handling  
capacity than the total maximum current drawn  
by each amplifier.  
Self-tapping screws  
Power control wire*  
7
8
7
(ø4 × 16 mm)  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
4.Connect the speaker wires.  
HPF  
5.Connect the power wire, power control wire  
and grounding wire following this order.  
6.Install the unit in the car.  
Installation  
Speaker stereo connection  
Speaker bridge connection  
1-channel system  
7.Connect the negative - terminal of the battery.  
Since the power amplifier has no parts which require  
operation, it can be installed at a position away from  
the driver’s seat without any hindrances.  
As generally accepted positions for its installation,  
places such as inside the trunk, etc. can be  
considered.  
L
L
L
2WARNING  
Lead terminal*  
Left speaker  
Lead terminal*  
4
4
CENTER  
UNIT  
R
R
To prevent fire caused by a short in the wiring,  
connect a fusible link or breaker nearby the  
battery’s positive terminal.  
L
L
R
Right speaker  
R
R
RIGHT  
RIGHT  
D
2CAUTION  
5
D
5
GE  
E
BRID  
LEFT  
BRIDG  
LEFT  
2CAUTION  
• Be sure to turn the power off before changing the  
setting of any switch.  
2CAUTION  
KAC-5201  
8
KAC-6201  
• Do not install the unit under the carpet. Otherwise  
heat build-up occurs and the unit may be damaged.  
• Install this unit in a location which allows heat to  
easily dissipate. Once installed, do not place any  
object on top of the unit.  
• The surface temperature of the amplifier will  
become hot during use. Install the amplifier in a  
place where people, resins, and other substances  
that are sensitive to heat will not come into contact  
with it.  
• When making a hole under a seat, inside the trunk,  
or somewhere else in the vehicle, check that there  
is nothing hazardous on the opposite side such as a  
gasoline tank, brake pipe, or wiring harness, and be  
careful not to cause scratches or other damage.  
• Do not install near the dashboard, rear tray, or air  
bag safety parts.  
• The installation to the vehicle should securely fasten  
the unit to a place in which it will not obstruct  
driving. If the unit comes off due to a shock and hits  
a person or safety part, it may cause injury or an  
accident.  
7
8
To prevent damage to the machine, take the  
following precautions:  
7
• If the fuse blows, check wires for shorts, then  
replace the fuse with one of the same rating.  
• Check that no unconnected cables or connectors  
are touching the car body. Do not remove caps from  
unconnected cables or connectors to prevent short  
circuits.  
• Connect the speaker wires to appropriate speaker  
connectors separately. Sharing the negative wire of  
the speaker or grounding speaker wires to the metal  
body of the car can cause this unit to fail.  
• After installation, check that the brake lamps,  
winkers, and wipers work properly.  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
HPF  
• Be sure the unit is connected to a 12V DC power  
supply with a negative ground connection.  
• Do not open the top or bottom covers of the unit.  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of water  
splashing.  
• When replacing a fuse, only use a new one with the  
prescribed rating. Using a fuse with the wrong rating  
may cause your unit to malfunction.  
Speaker Selection  
• The rated input power of the speakers that are  
going to be connected should be greater than  
the maximum output power (in Watts) of the  
amplifier. Use of speakers having input power  
ratings that are less than the output power of  
the amplifier will cause smoke to be emitted as  
well as damage.  
Tri-mode  
Subwoofer  
Left speaker  
Right speaker  
L
Crossover Frequency  
High pass  
C
0 dB  
L
L
Power wire connection  
CENTER  
UNIT  
Subwoofer  
(L + R)  
-3 dB  
R
R
C
L
C
• The impedance of the speakers that are going to  
be connected should be 2or greater (for  
stereo connections), or 4or greater (for  
bridged connections). When more than one set  
of speakers are going to be used, calculate the  
combined impedance of the speakers and then  
connect suitable speakers to the amplifier.  
• To prevent a short circuit when replacing a fuse, first  
disconnect the wiring harness.  
KAC-5201  
KAC-6201  
Frequency  
Speaker level input terminals (!)  
• The genuine-accessory car stereo shall have a  
maximum power output of no more than 40 W.  
• Do not connect the speaker output leads from  
a power amplifier (Optional) to the speaker  
level input terminals of this unit, for this may  
cause malfunction or damage.  
• Do not connect cables and leads to both RCA  
cable input jacks and the speaker level input  
terminals simultaneously, for this may cause  
malfunction or damage.  
• Connect the power control lead to a power  
supply which can be turned ON/OFF by the  
ignition key switch (ACC line). With this  
connection, shock noise may be generated  
when the power of the genuine-accessory car  
stereo is switched ON/OFF.  
8
7
8
7
159000  
159000  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
NOTE  
C=  
L=  
(µF)  
=
= 331.25 µF  
= 5.3 mH  
HPF  
fc x R  
159 x R  
fc  
120Hz x 4Ω  
159 x 4Ω  
120Hz  
234  
• If you experience problems during installation,  
consult your Kenwood dealer.  
Lead terminal*  
Terminal cover  
(mH) =  
• If the unit does not seem to be working right, consult  
your Kenwood dealer.  
Principle of Tri-mode  
4Ω  
2CAUTION  
Method of frequency band division using a coil  
and capacitor ... in case of 6dB/oct. slope  
Coil (L): Passes low frequencies and blocks  
high frequencies. (Low pass)  
4Ω  
4Ω  
Cleaning the unit  
• If you wish to bridge-connect a speaker, the  
speaker impedance must be no less than 4  
ohms. Connecting a speaker with an  
impedance lower than 4 ohms may damage  
the unit.  
• Be sure to connect capacitors to speakers to  
which high frequencies will be passed.  
Failure to do so will result in a drop of the  
combined impedance with the subwoofer.  
• Ensure that the withstand voltage and  
current ratings of the capacitors (C) and coils  
(L) are sufficient.  
4Ω  
If the front panel gets dirty, turn off the power and  
wipe the panel with a dry silicon cloth or soft cloth.  
• After installing the unit, check to make sure that  
electrical equipment such as the brake lamps, turn  
signal lamps and windshield wipers operate  
normally.  
8 Ω  
2 Ω  
Power control wire*  
Ground wire*  
Capacitor (C): Passes high frequencies and  
blocks low frequencies. (High pass)  
2CAUTION  
Battery wire*  
Do not wipe the panel with a hard cloth or a cloth  
dampened by volatile solvents such as paint thinner  
and alcohol. They can scratch the surface of the panel  
and/or cause the indicator letters to peel off.  
Self-tapping screw  
(ø4 × 16 mm)  
Example:  
When it is required to set a crossover  
frequency of 120 Hz using speakers with an  
impedance of 4 ohms.  
Protective Fuse*  
Battery  
fc=Cut of Frequency (Hz)  
R=Speaker Impedance ()  
Power terminal (234)  
Connect to their respective terminals the power  
supply wire, and ground wire, all of which pass  
through the associated terminal cover. Once the  
connections are complete, place the cover on  
the terminal section.  
Installation board, etc.  
(thickness : 15 mm or more)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
故障檢修  
有時被認為是故障的現象﹐其實是因微小的操作或配線失誤而造成。在要求維修之前﹐請參照下表稍  
事檢查為盼。  
控制  
現象  
原因  
排除方法  
9
KAC-5201  
KAC-6201  
KAC-6201  
KAC-5201  
0.5 0.3  
沒有聲音(一側無聲音)  
●輸入(或輸出)纜線未連接。  
●保護線路可能被觸發。  
●連接輸入(或輸出)纜線。  
●參考“電源指示燈”一節,檢查  
連接狀況。  
●請更換保險絲 , 減小音量。  
●確認揚聲器線 , 解除短路原因後 ,  
更換保險絲。  
10  
1.0  
15  
20  
(W)  
6 7 89  
0
0
!
!
1234  
5
KAC-6201  
KAC-5201  
放大器  
(保險絲跳斷)  
●音量過大。  
●揚聲器電線短路。  
MIN  
INPUT  
SENSITIVITY(V)  
MAX  
25W 或更大  
輸出水平過低(或過高)  
聲音質量很差(聲音失真)  
輸入敏感度調節不當,沒有位于妥 調節該控制器。請參考“控制”。  
當位置。  
KAC-5201  
KAC-6201  
6 7 89  
電源指示燈  
●揚聲器纜線的極性 +/- 連接錯 ●請將纜線的極性 +/- 連接正  
誤。  
●揚聲器纜線的一根被車體螺釘壓 ●重新連接纜線,使之不再受螺釘  
確。  
根據本機所連接的中心裝置和揚聲器等條件,需  
要進行以下控制及開關切換操作。  
MONO(Lch單聲-聲道)位置  
只放大從左聲道輸入的信號。切換到此位  
置可以進行橋路連接,作為大功率單聲道  
放大器使用(輸入的右聲道信號不輸  
出)。  
使用說明書  
POWER AMPLIFIER  
2 注意  
電源指示燈  
當電源打開時,電源指示燈點亮。  
如果當電源被打開,但該指示燈卻不點亮時,也  
有可能是因為保護功能被激活。請檢查是否有出  
現故障的跡象。  
該端子不能作為電源的接地端子。如果將電  
源的地線連接到此端子就會損壞本機。  
迫。  
●開關的設定可能不妥。  
壓迫。  
●請參考“系統配置實例”,將開  
關正確設置。  
1 保險絲  
25 A × 1 : KAC-6201  
15 A × 1 : KAC-5201  
7 FILTER(過濾器)開關  
這些開關可以過濾揚聲器的輸出信號。  
INSTRUCTION MANUAL  
9 INPUT SENSITIVITY(輸入敏感度)控制  
根據連接到本機的中心裝置的前置輸出水  
平,設定本控制旋鈕的位置;對于原裝的車  
用立體聲,可以設置為最大功率輸出。  
請參考右圖進行設置。  
HPF(高頻通過)位置 (只限於 KAC-  
6201)  
只讓那些等於或高於 150 Hz 的信號通過  
(低於 150 Hz 的信號被過濾掉)。  
萬一在銷售店等找不到指定容量的保險絲的  
, 請與 KENWOOD 專銷公司聯係。  
在以下場合中保護功能被激活:  
本機裝有保護功能,可以保護本機以及揚聲  
器不會受到可能發生的各種意外事故的損  
害。  
規格  
規格可能會變更﹐恕不另行通知。  
2 電池端子  
LPF (低頻通過)位置  
3 接地端子  
關於前置輸出水平及最大功率輸出,可以參  
考中心裝置的使用說明書的“規格”部分。  
只讓那些等於或低於 80 Hz 的信號通過  
(高於 80 Hz 的信號被過濾掉)。  
即使當操作開關位於 STEREO(立體聲)  
時,左右聲道的信號在輸出前將被混合。  
音頻部 ................................................................... KAC-6201 KAC-5201  
最大功率輸出 ...................................................................................... 350 W × 1 250 W × 1  
額定輸出功率(4 歐姆)  
20 Hz - 20 kHz0.08% THD ............................................. 60 W × 2 40 W × 2  
橋路(1 kHz 0.8% THD............................................................ 150 W × 1 120 W × 1  
額定輸出功率(2 歐姆)  
當保護功能被觸發時,電源指示燈將熄滅,  
放大器也停止工作。  
4 電源控制(REMOTE)端子  
● 當揚聲器纜線短路時。  
● 當揚聲器的輸出接地時。  
5 揚聲器輸出端子  
立體聲連接端子:  
0 LINE IN子  
OFF(關閉)位置  
未經過濾的信號原樣輸出。  
當您希望本機作為立體聲放大器時,必須  
使用立體聲連接端子。  
● 當本機出現誤動作,有 DC(直流)信號  
傳送到揚聲器輸出端時。  
! 揚聲器水平輸入端子  
普通(1 kHz 0.8% THD.............................................................. 75 W × 2 60 W × 2  
頻率響+0-1 dB............................................................. 10 Hz ~ 45 kHz 5 Hz ~ 50 kHz  
信噪比 ...................................................................................................... 100 dB 100 dB  
敏感最大)(額定輸出....................................................................... 0.2 V 0.2 V  
敏感(最小)(額定輸出....................................................................... 5.0 V 5.0 V  
輸入阻抗 .................................................................................................... 10 k10 kΩ  
低頻通過過濾(12 dB/oct........................................................................ 80 Hz 80 Hz  
高頻通過過濾(12 dB/oct.只限於 KAC-6201.................................... 150 Hz  
8 OPERATION(操作)開關  
本開關可以用來選擇輸入信號的放大方法。  
橋路連接端子:  
● 內部高溫不能動作時  
當您希望本機作為大功率單聲道放大器使  
用時,可以進行橋路連接。(連接 LEFT 聲  
道(+)、 RIGHT 聲道(-)及 SPEAKER  
OUTPUT 端子)  
● 當中心裝置(錄音卡座、 CD 接收機等)  
或本機的地線沒有連接到作為電氣地線的  
金屬部件而向電池負極(-)端子輸送電流  
時。  
STEREO(立體聲)位置  
放大器可以作為立體聲放大器使用。  
L+R 位置(只限於 KAC-6201)  
輸入的左右聲道信號在放大之前被混合。  
當裝置被用於副低音揚聲器或者需要 L+R  
(單聲道)效果時,可以使用此位置。  
6 RCA 纜線接地接頭  
當使用具有接地引線的 RCA 纜線時,將接地  
引線連接到此端子。  
共同 ....................................................................... KAC-6201 KAC-5201  
使用電壓(允許 11-16 ........................................................................ 14.4 V 14.4 V  
電流消耗(1 kHz 10% THD................................................................... 19 A 16 A  
尺寸(W × H × D毫米.......................................................... 228 × 59 × 228 228 × 59 × 160  
尺寸(W × H × D(英寸............................................................ 9 × 2-5/16 × 9 9 × 2-5/16 × 6-5/16  
重量 ............................................................................................. 2.8 kg (6.1 lbs) 2.1 kg (4.6 lbs)  
系統配置實例  
2 通道系統  
連接  
為了安全安裝 , 請在開始操作之前 , 務必閱讀「安裝步驟」說明。  
左揚聲器  
右揚聲器  
© B64-2562-00/00 (MV)  
L
L
中心裝置  
R
R
RCA 纜線  
連接揚聲器水平輸入  
右揚聲器  
左揚聲器  
原裝車用立體聲  
(沒有輸出的中  
心裝置等)  
中心裝置  
(錄音卡座、  
CD 接收機等)  
KAC-5201  
8
KAC-6201  
7
8
7
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
FILTER  
OFF  
FILTER  
OFF  
RCA 纜線  
(另售品)  
HPF  
LPF STEREO MONO(Lch)  
汽車保險絲盒  
安裝  
安裝步驟  
安全注意事項  
ACC  
副低音揚聲器系統  
接線  
1. 拔取點火鑰匙,拆掉電池負極(-)端子,以  
防短路。  
因為放大器中不包含需要隨時操作的部件,所以  
可以安裝在遠離駕駛位置的不造成障礙的位置。  
通常,可供參考的安裝地點大致為行李箱等處。  
2 警告  
左揚聲器  
● 如果發動機運轉時從揚聲器中發出噪音,可以  
蓄電池  
中心裝置  
為了防止受傷和火災﹐請遵守下列注意事項。  
在電池的每根連線上加一個線路噪音過濾器  
● 當延長蓄電池導線和接地導線時﹐請使用車輛  
(選購件)。  
2. 根據使用目的,設置本機到妥當位置。  
3. 連接本機的輸入和輸出纜線。  
4. 連接揚聲器纜線。  
5. 按順序連接電源線,電源控制纜線及地線。  
6. 將本機安裝到車中。  
右揚聲器  
T
6
!
ER  
EAK  
L
INPU  
RIGHT  
E
LEV  
用導線或 3mm2AWG12)以上的導線﹐以  
GND  
2 注意  
P
S
L
L
LEFT  
● 使用絕緣圈,以防纜線直接接觸貼片的邊緣。  
副低音揚聲器  
防止導線劣化和被覆面的損傷。  
● 將接地線連接到車架的金屬部位,車架起到車  
● 為了防止短路等事故﹐請勿將金屬物品(硬  
● 不可將本裝置安裝在絨毯底下,否則,蓄熱  
會導致本裝置損壞。  
R
R
輛電氣接地的作用,將電流傳遞到電池的負極  
幣、工具等)掉落在裝置中。  
● 將本裝置安裝在熱量容易發散的地點。  
一旦安裝完畢,不可在其上放置其它物品。  
-)。如果接地線沒有連接就不要打開電源開  
KAC-5201  
8
KAC-6201  
● 萬一裝置冒煙或有異味時﹐請立即關閉電源﹐  
關。  
7. 連接電池的負極(-)。  
2 警告  
電源控制纜線 (市售品)  
7
8
並與 KENWOOD 經銷商洽談。  
7
● 機器使用過程中,機體表面會發熱昇溫。所  
以其安裝地點應該是人體,樹脂及其它熱敏  
感物質不易觸及的地方。  
● 應務必在蓄電池附近的電源連接線上設置保險  
● 在使用中請盡量不要接觸機器表面。因為機器  
絲。保險絲的規格應該與本機的保險絲容量相  
在使用中表面發熱會燙傷人體。  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
為了防止短路所引起的火災,在電池的正極附  
近連接保險絲或斷電器。  
HPF  
同或者略大。  
● 在車座、行李箱底部或車子其它部位打洞  
時,應確認其背面沒有會受到損壞的物件,  
諸如油箱、剎車用配管或線路管套等,千萬  
不可擦傷或損壞這些物品。  
● 對於電源連接線和接地線﹐請使用電流容量大  
於本機保險絲容量的汽車用(防火)電源連接  
2 注意  
連接立體聲揚聲器  
連接立體聲的橋路  
2 注意  
1 通道系統  
● 在變更開關的設定時,必須首先切斷電源。  
線。(請使用截面積為 3mm2AWG12)或  
者以上的電源連接線。)  
● 當保險絲熔斷後,要檢查纜線是否有短路,  
並更換上相同規格的保險絲。  
為了防止裝置發生故障﹐請遵守下列注意事項﹐  
正確操作和使用。  
引出端子(市售品)  
引出端子(市售品)  
L
4
4
L
L
左揚聲器  
● 不可安裝在駕駛室儀表板、尾部底板或保險  
氣囊等部件之上。  
● 當使用多個功率放大器時,電源導線的電流容  
量及保險絲的容量要大於各個放大器的最大使  
用電流之和。  
中心裝置  
R
R
● 檢查是否有尚未連接的纜線或與車體相接觸  
的端頭。未連接纜線及其端部的保護帽不可  
拆掉,以防短路。  
● 請以負接地線的 12V 直流電源向本裝置供  
電。  
● 請勿打開頂部和底部的蓋子。  
● 將本機安裝在車內時,應確保固定牢靠,且  
不會對駕車造成妨礙。如果因為沖擊造成本  
機脫落且撞及人體或保險部件,就會導致傷  
害或事故。  
L
L
R
右揚聲器  
R
R
RIGHT  
RIGHT  
5
5
● 揚聲器的纜線要分別連接到各自的端子。共  
用揚聲器的負極纜線或將揚聲器端子接地到  
汽車的金屬部分,都會導致本機停止工作。  
● 請勿將本裝置安裝在曝露於直射陽光、高溫或  
高濕、水可能飛濺的或有灰塵的地方。  
BRIDGED  
LEFT  
BRIDGED  
LEFT  
揚聲器選擇  
● 準備連接的揚聲器的額定功率要大於放大器的  
KAC-5201  
8
KAC-6201  
● 在本裝置安裝之後,應該確認電氣設備,比  
如剎車燈、轉向信號燈以及雨刷等操作正  
常。  
● 更換保險絲時﹐請更換規定容量相同的保險  
最大輸出功率。如果揚聲器的額定功率小於放  
絲﹐如使用不同容量的保險絲﹐可能會造成裝  
7
8
7
● 安裝之後,請檢查汽車的剎車燈、方向指示  
燈、雨刷等是否正常動作。  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
大器的最大輸出功率則會導致揚聲器冒煙以至  
置的故障。  
● 更換保險絲時﹐為了防止短路事故﹐請先拔下  
HPF  
損壞。  
揚聲器水平輸入端子 (!)  
● 車內原裝立體聲的最大輸出功率不得大於 40  
瓦。  
自攻絲螺絲  
(φ 4 x 16 mm)  
● 所連接的揚聲器的阻抗必須為 2 歐姆或更高  
(立體聲連接時);或者 4 歐姆或更高(橋路  
連接)。當多個揚聲器被連接時,則必須計算  
電源線束再進行更換。  
三模式  
左揚聲器  
右揚聲器  
副低音揚聲器  
高頻通過  
L
交叉頻率  
● 不要將揚聲器的輸出引線從功率放大器(選  
購件)連接到本機的揚聲器的輸入端子。否  
則,將造成誤動作或損壞。  
揚聲器的綜合阻抗,再將妥當的揚聲器與放大  
器相連接。  
C
0 dB  
連接電源線  
● 安裝有困難時﹐請與 KENWOOD 經銷商洽  
談。  
L
L
副低音揚聲器  
(L+R)  
中心裝置  
-3 dB  
R
R
● 不可同時連接纜線和引線到 RCA 纜線輸入  
端子及揚聲器輸入端子。否則,將造成誤動  
作或損壞。  
C
4  
● 如果仍不能恢復正常時﹐請與 KENWOOD 經  
銷商洽談。  
L
C
4Ω  
4Ω  
4Ω  
安裝基板,等  
(厚度﹕不小於 15 mm)  
KAC-5201  
KAC-6201  
● 將電源控制導線連接到起動鑰匙可以控制開  
關(ACC 線)的電源上。  
在這樣連接的場合,當車內原裝立體聲電源  
頻率  
8  
2 Ω  
8
7
8
7
159000  
C=  
159000  
120Hz x 4 Ω  
159 x 4 Ω  
120Hz  
裝置的保養  
如果外表髒污時﹐請關閉電源﹐使用干燥的硅布  
或柔軟的布匹擦拭。  
(µF) =  
(mH) =  
= 331.25 (µF)  
OPERATION  
LPF STEREO MONO(Lch)  
OPERATION  
L+R  
LPF STEREO MONO(Lch)  
FILTER  
OFF  
FILTER  
OFF  
fc x R  
159 x R  
234  
HPF  
引出端子(市售品)  
端子套  
開關時,可能產生沖擊噪音。  
L=  
fc  
= 5.3 (mH)  
電源端子 (234)  
2 注意  
將電源控制線、電源線、地線同時穿過端子套  
分別連接到各自對應的端子。當連接完畢後,  
將端子套套緊於端子上。  
請勿使用硬布或塗料稀釋劑、酒精等揮發性溶  
劑﹐以免損壞外表面或將所附指示字符擦掉。  
三模式的原理  
使用線圈及電容進行頻率區分的方法 ... 6dB/  
oct. 的條件下  
線圈 (L): 讓低頻通過,阻塞高頻(低頻通過)  
電容 (C): 讓高頻通過,阻塞低頻(高頻通過)  
2 注意  
● 當您將本機與揚聲器進行橋路連接時,所連  
接的揚聲器的阻抗必須為 4 歐姆或更高。如  
果所連接的揚聲器的阻抗小於 4 歐姆,就會  
損壞本機。  
附件  
電源控制纜線 (市售品)  
接地導線 (市售品)  
零件名稱  
外觀  
項目數量  
蓄電池導線 (市售品)  
● 對於高頻通過的揚聲器要連接一個電容器。  
否則,將造成與副低音揚聲器連接的綜合阻  
抗下降。  
端子套(電源端子)  
1
實例  
當使用的揚聲器的阻抗為 4 歐姆,所需要的交叉  
頻率為 120 Hz 時。  
fc= 阻斷頻率 (Hz)  
R= 揚聲器阻抗 (Ω)  
自攻絲螺絲  
(φ 4 x 16 mm)  
● 確保電容器(C)和線圈(L)的允許電壓和  
額定電流符合要求(足夠大)。  
4
保護保險絲  
(市售品)  
蓄電池  
Download from Www.Somanuals.com. All Manuals Search And Download.  

JBL Portable Speaker D38 User Manual
JVC Car Video System DT X91C User Manual
JVC Computer Monitor TM A14E User Manual
JVC Digital Camera GR D24 User Manual
Kenwood Car Video System DDX2071 User Manual
Kompernass Laminator KH 4418 User Manual
Kompernass Saw PKGS1450 User Manual
Konica Minolta Universal Remote VI 300 User Manual
Kramer Electronics Car Amplifier VP 200D User Manual
Kramer Electronics Switch VS 66FW User Manual