Dear Customer,
Thank you for purchasing this digital
video camera. Before use, please read
the safety information and precautions
contained in the pages 2 – 3 to ensure
safe use of this product.
ENGLISH
DIGITAL VIDEO CAMERA
GETTING STARTED
5
10
14
27
39
GR-D24
VIDEO RECORDING &
PLAYBACK
ADVANCED FEATURES
REFERENCES
TERMS
Please visit our Homepage on the World Wide Web for
Digital Video Camera:
For Accessories:
To deactivate the demonstration, set
“DEMO MODE” to “OFF”.
(੬ pg. 14, 16)
INSTRUCTIONS
EN
LYT1240-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
2
EN
SAFETY PRECAUTIONS
IMPORTANT (for owners in the U.K.)
Connection to the mains supply in the United
Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point, then
NOTES:
● The rating plate (serial number plate) and safety caution
are on the bottom and/or the back of the main unit.
● The rating information and safty caution of the AC
Adapter are on its upper and lower sides.
When the equipment is installed in a cabinet or on a shelf,
make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and at
the rear).
obtain an appropriate safety approved extension lead or
consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted, and to replace the
fuse cover.
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or
cloth etc. the heat may not be able to get out.)
If nonetheless the mains plug is cut off be sure to remove
the fuse and dispose of the plug immediately, to avoid
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
DO NOT make any connection to the Larger Terminal
coded E or Green.
The wires in the mains lead are coloured in accordance
with the following code:
No naked flame sources, such as lighted candles, should
be placed on the apparatus.
When discarding batteries, environmental problems must
be considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or places with
water.
Blue to N (Neutral) or
Black
Also do not place any containers filled with water or liquids
(such as cosmetics or medicines, flower vases, potted
plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
Brown to L (Live) or
Red
If these colours do not correspond with the terminal
identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
Do not point the lens or the viewfinder directly into the sun.
This can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a risk of
fire or electric shock.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION!
The following notes concern possible physical damage to
the camcorder and to the user.
CAUTIONS:
● To prevent shock, do not open the cabinet. No user
serviceable parts inside. Refer servicing to qualified
personnel.
● When you are not using the AC Adapter for a long period
of time, it is recommended that you disconnect the
power cord from AC outlet.
When carrying, be sure to always securely attach and use
the provided strap. Carrying or holding the camcorder by
the viewfinder and/or the LCD monitor can result in
dropping the unit, or in a malfunction.
Take care not to get your finger caught in the cassette
holder cover. Do not let children operate the camcorder, as
they are particularly susceptible to this type of injury.
CAUTION:
To avoid electric shock or
damage to the unit, first
firmly insert the small end
of the power cord into the
AC Adapter until it is no
longer wobbly, and then
plug the larger end of the
power cord into an AC
outlet.
Do not use a tripod on unsteady or unlevel surfaces. It
could tip over, causing serious damage to the camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the
camcorder and leaving it on top of the TV is not
recommended, as tripping on the cables will cause the
camcorder to fall, resulting in damage.
CAUTIONS:
● This camcorder is designed to be used with PAL-type
colour television signals. It cannot be used for playback
with a television of a different standard. However, live
recording and LCD monitor/viewfinder playback are
possible anywhere.
● Use the JVC BN-V408U/V416U/V428U battery packs
and, to recharge them or supply power to the camcorder
from an AC outlet, use the provided multi-voltage AC
Adapter. (An appropriate conversion adapter may be
necessary to accommodate different designs of AC
outlets in different countries.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
SOME DO’S AND DON’TS ON THE SAFE USE OF
EQUIPMENT
This equipment has been designed and
manufactured to meet international safety standards
but, like any electrical equipment, care must be taken
if you are to obtain the best results and safety is to
be assured.
This camcorder is designed exclusively for the digital video
cassette. Only cassettes marked “
this unit.
” can be used with
DO read the operating instructions before you attempt to use
the equipment.
Before recording an important scene…
…make sure you only use cassettes with the Mini DV mark
.
…remember that this camcorder is not compatible with other
digital video formats.
…remember that this camcorder is intended for private
consumer use only. Any commercial use without proper
permission is prohibited. (Even if you record an event such as
a show, performance or exhibition for personal enjoyment, it
is strongly recommended that you obtain permission
beforehand.)
DO ensure that all electrical connections (including the mains
plug, extension leads and interconnections between pieces
of equipment) are properly made and in accordance with the
manufacturer’s instructions. Switch off and withdraw the
mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or if it is damaged in any way
— switch off, withdraw the mains plug and consult your
dealer.
DON’T remove any fixed cover as this may expose
dangerous voltages.
DON’T leave equipment switched on when it is unattended
unless it is specifically stated that it is designed for
unattended operation or has a standby mode. Switch off
using the switch on the equipment and make sure that your
family knows how to do this. Special arrangements may need
to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so
that you are distracted from the requirements of road safety. It
is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can
permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example
with curtains or soft furnishings. Overheating will cause
damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood
screws — to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings
provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ABOVE ALL
● NEVER let anyone especially children push anything into
holes, slots or any other opening in the case — this could
result in a fatal electrical shock;
● NEVER guess or take chances with electrical equipment of
any kind — it is better to be safe than sorry!
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
How To Attach The Lens Cap
To protect the lens, attach
the provided lens cap to
the camcorder as shown
in the illustration.
EN
5
Provided Accessories
or
NOTE:
To confirm the lens cap is on
correctly make sure the cap
is flush to the camcorder.
Push.
Place here during
shooting.
How To Attach The Shoulder Strap
Follow the illustration.
1 Thread the strap through the eyelet.
2 Fold it back and thread it through the strap guide and
the buckle.
● To adjust the length of the strap, loosen and then tighten
the strap in the buckle.
a AC Adapter AP-V14E or AP-V15E
b Power Cord
c Battery Pack BN-V408U-B
3 Slide the strap guide fully towards the eyelet.
d Audio/Video Cable (ø3.5 mini-plug to RCA plug)
e Core Filter (for optional S-Video Cable. ੬ pg. 6 for
attachment)
Strap guide
2
f Shoulder Strap (See the right column for attachment)
g CD-ROM
h Lens Cap (See the right column for attachment)
i Cable Adapter
Buckle
NOTES:
● In order to maintain optimum performance of the
camcorder, provided cables may be equipped with one or
more core filter. If a cable has only one core filter, the end
that is closest to the filter should be connected to the
camcorder.
3
● Make sure to use the provided cables for connections. Do
not use any other cables.
1
Eyelet
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
6
EN
How To Attach The Core Filter (for optional S-Video
Cable)
Power
Power Switch
Attach the core filters to the cables. The core filter
reduces interference.
POWER/CHARGE lamp
Lock Button
1 Release the stoppers on both ends of the core filter.
Stopper
Battery pack
mount
2 Run the cable through the core filter, leaving approx.
3 cm of cable between the cable plug and the core filter.
Wind the cable once around the outside of the core filter
as shown in the illustration.
Arrow
To DC connector
Mark
● Wind the cable so that it is not slack.
3 cm
Battery pack
BATT.RELEASE
AC Adapter
Power Cord
Wind once.
3 Close the core filter until it clicks shut.
To AC outlet
This camcorder’s 2-way power supply system lets you
choose the most appropriate source of power. Do not use
provided power supply units with other equipment.
Charging The Battery Pack
NOTES:
● Take care not to damage the cable.
● When connecting a cable, attach the end with the core filter
to the camcorder.
1 With the arrow on the battery pack pointing upward,
push the battery pack slightly against the battery pack
mount a.
2 Slide up the battery pack until it locks in place b.
3 Set the Power Switch to “OFF (CHARGE)”.
4 Connect the AC Adapter to the camcorder, then
connect the Power Cord to the AC Adapter.
5 Plug the AC Adapter into an AC outlet. The POWER/
CHARGE lamp on the camcorder blinks to indicate
charging has started.
6 When the POWER/CHARGE lamp goes out, charging
is finished. Unplug the AC Adapter from the AC outlet.
Disconnect the AC Adapter from the camcorder.
To detach the battery pack
Slide the battery pack down slightly while sliding BATT.
RELEASE to detach it.
Battery pack
BN-V408U*
Charging time
Approx. 1 hr. 30 min.
Approx. 3 hr.
BN-V416U
BN-V428U
* Provided
NOTES:
Approx. 5 hr.
● If the protective cap is attached to the battery pack, remove
it first.
● During charging, the camcorder cannot be operated.
● Charging is not possible if the wrong type of battery is used.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
7
● When charging the battery pack for the first time or after a
long storage period, the POWER/CHARGE lamp may not
light. In this case, remove the battery pack from the
camcorder, then try charging again.
● If the battery operation time remains extremely short even
after having been fully charged, the battery is worn out and
needs to be replaced. Please purchase a new one.
● For other notes, ੬ pg. 27.
The Benefits Of
Lithium-Ion Batteries
Lithium-ion battery packs
are small but have a large
power capacity. However,
when one is exposed to
cold temperatures (below
10°C), its usage time
becomes shorter and it
may cease to function. If
this happens, place the
battery pack in your pocket
or other warm, protected
place for a short time, then
re-attach it to the camcorder. As long as the battery pack
itself is not cold, it should not affect performance.
(If you’re using a heating pad, make sure the battery pack
does not come in direct contact with it.)
Using The Battery Pack
Perform steps 1 – 2 in “Charging The Battery Pack”.
Lithium-ion is vulnerable in
colder temperatures.
Maximum continuous recording time
Battery pack
BN-V408U*
BN-V416U
LCD monitor on
1 hr. 10 min.
Viewfinder on
1 hr. 40 min.
2 hr. 20 min.
3 hr. 15 min.
5 hr. 50 min.
BN-V428U
4 hr. 10 min.
For other notes, ੬ pg. 27.
* Provided
NOTES:
● Recording time is reduced significantly under the following
conditions:
Grip Adjustment
• Zoom or Record-Standby mode is engaged repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
• The White LED Light is used.
● Before extended use, it is recommended that you prepare
enough battery packs to cover 3 times the planned
shooting time.
1 Adjust the velcro strip.
2 Pass your right hand through the loop and grasp the
grip.
3 Adjust your thumb and fingers through the grip to
easily operate the Recording Start/Stop Button, Power
Switch and Power Zoom Lever. Be sure to fasten the
velcro strip to your preference.
ATTENTION:
Before detaching the power source, make sure that the
camcorder’s power is turned off. Failure to do so can result in
a camcorder malfunction.
Using AC Power
Connect the AC Adapter to the camcorder, then connect
the Power Cord to the AC Adapter as shown in the
illustration on page 6.
NOTES:
● The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
● Do not allow the DC terminals of the AC Adapter to come in
contact with metals, as this can result in a short circuit and
cause malfunction.
● For other notes, ੬ pg. 27.
About Batteries
DANGER! Do not attempt to take the batteries apart, or
expose them to flame or excessive heat, as it may cause
a fire or explosion.
WARNING! Do not allow the battery or its terminals to
come in contact with metals, as this can result in a short
circuit and possibly start a fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
8
EN
3 Press the MMENU/VOL. Wheel in. The Menu Screen
Operation Mode
To turn on the camcorder, set the Power Switch to any
operation mode except “OFF (CHARGE)” while pressing
down the Lock Button located on the switch.
appears.
CAMERA DISPLAY
4 Rotate the MMENU/VOL.
BR I GHT
Wheel to select “n”, and press it.
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF
2 0 . 1 2
1 7
The CAMERA DISPLAY Menu
appears.
.
:
0 4
3 0
ADJ .
POWER/CHARGE lamp
5 Rotate the MMENU/VOL.
Wheel to select “CLOCK ADJ.”,
and press it. The parameter for
“Day” is highlighted.
RETURN
Power Switch
Lock Button
CAMERA DISPLAY
6 Rotate the MMENU/VOL.
Wheel to input the day, and press
it. Repeat to input the month, year,
hour and minute.
CLOCK
ADJ .
2 0 . 1 2
.
0 4
MMENU/VOL.
1 7 : 3 0
7 Rotate the MMENU/VOL.
Wheel to select “BRETURN”, and
press it twice. The Menu Screen closes.
NOTE:
Even if you select “CLOCK ADJ.”, if the parameter is not
highlighted, the camcorder’s internal clock continues to
Choose the appropriate operation mode according to
your preference using the Power Switch.
operate. Once you move the highlight bar to the first date/
time parameter (day), the clock stops. When you finish
setting the minute and press the MMENU/VOL. Wheel in, the
date and time begin operation from the date and time you
have just set.
Power Switch Position
A (Full Auto Recording):
Allows you to record using NO special effects or
The “A” indicator appears on the display.
Viewfinder Adjustment
M (Manual Recording):
Allows you to set various recording functions using the
Menus. (੬ pg. 14)
1 Set the Power Switch to “A” or “M” while pressing
down the Lock Button located on the switch.
If you want more creative capabilities than Full Auto
Recording, try this mode.
There is no indication on the display.
2 Make sure the LCD monitor is closed and locked. Pull
out the viewfinder fully and adjust it manually for best
viewability.
3 Turn the Dioptre Adjustment Control until the
OFF:
indications in the viewfinder are clearly focused.
Allows you to switch off the camcorder.
PLAY:
● Allows you to play back a recording on the tape.
● Allows you to set various playback functions using
the Menus. (੬ pg. 14)
Power-Linked Operation
turn on/off the camcorder by opening/closing the LCD
monitor or pulling out/pushing in the viewfinder.
PAUSE
INFORMATION:
The following explanations in this manual supposes the
use of LCD monitor in your operation. If you want to use
the viewfinder, close the LCD monitor and pull out the
viewfinder fully.
Dioptre Adjustment Control
CAUTION:
When retracting the viewfinder, take care not to pinch your
fingers.
Date/Time Settings
The date/time is recorded onto the tape at all times, but
its display can be turned on or off during playback.
(੬ pg. 14, 17)
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
9
Brightness Adjustment Of The Display
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or eject a
1 Set the Power Switch to “M”
MMENU/VOL.
or “PLAY” while pressing down
the Lock Button located on the
switch.
cassette.
OPEN/EJECT
Cassette holder
cover
2 Open the LCD monitor fully.
(੬ pg. 10)
3 Press the MMENU/VOL.
Wheel in. The Menu Screen
appears.
PUSH HERE
4 Rotate the MMENU/VOL.
Wheel to select “n”, and
press it. The CAMERA
Make sure the
DISPLAY Menu appears.
BRIGHT
window side is facing
out.
Cassette holder
5 Rotate the MMENU/VOL.
Wheel to select “BRIGHT”, and press it. The Menu
Screen closes and the brightness control indicator
appears.
Erase protection tab
1 Slide and hold OPEN/EJECT in the direction of the
arrow, then pull the cassette holder cover open until it
locks. The cassette holder opens automatically.
● Do not touch internal components.
6 Rotate the MMENU/VOL. Wheel until the appropriate
brightness is reached.
7 Press the MMENU/VOL. Wheel in.
● It is also possible to adjust the brightness of the viewfinder
by pulling out the viewfinder, setting “PRIORITY” in the
SYSTEM Menu to “FINDER” (੬ pg. 14, 16) and adjusting
as described above.
2 Insert or remove a tape and press “PUSH HERE” to
close the cassette holder.
● Be sure to press only the section labelled “PUSH HERE” to
close the cassette holder; touching other parts may cause
your finger to get caught in the cassette holder, resulting in
injury or product damage.
Tripod Mounting
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
● When the battery pack’s charge is low, you may not be able
to close the cassette holder cover. Do not apply force.
Replace the battery pack with a fully charged one or use
AC power before continuing.
To attach the camcorder to a
tripod, align the direction stud
and screw to the mounting
socket and stud hole on the
camcorder. Then tighten the
screw clockwise.
● Some tripods are not
equipped with studs.
3 Close the cassette holder cover firmly until it locks into
place.
CAUTION:
Approximate recording time
When attaching the camcorder
Recording mode
Tape
to a tripod, extend its legs to
stabilise the camcorder. It is not advised to use small sized
tripods. This may cause damage to the unit by falling over.
SP
LP
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
45 min.
90 min.
120 min.
To switch the recording mode, refer to pages 14 and 15.
To protect valuable recordings
Slide the erase protection tab on the back of the tape in
the direction of “SAVE”. This prevents the tape from
being recorded over. To record on this tape, slide the tab
back to “REC” before loading it.
For other notes, ੬ pg. 27.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN VIDEO RECORDING
10
Basic Recording
● To turn the beep sounds off, ੬ pg. 14, 16.
● For other notes, ੬ pg. 27.
LCD Monitor And Viewfinder
While using the LCD monitor:
Make sure the viewfinder is pushed back in. Press the
Monitor Opening Button and open the LCD monitor fully.
It can rotate 270° (90° downward, 180° upward).
NOTE:
Before continuing, perform the procedures listed below:
● Power (੬ pg. 6)
● Loading a Cassette (੬ pg. 9)
While using the viewfinder:
Make sure the LCD monitor is closed and locked. Pull out
the viewfinder fully.
Push.
● Be sure to pull out the viewfinder until you hear a click,
otherwise it may be pushed back in during use.
POWER/CHARGE lamp
Power Zoom Lever
Monitor Opening Button
NOTES:
monitor and the viewfinder. When the viewfinder is pulled
out while the LCD monitor is opened, you can select which
one to use. Set “PRIORITY” to the desired mode in
SYSTEM Menu. (੬ pg. 14, 16)
Power Switch
Lock Button
Recording Start/Stop Button
●
Coloured bright spots may appear all over the LCD monitor or
the viewfinder. However, this is not a malfunction. (੬ pg. 30)
Tape Remaining Time
1 Remove the lens cap.
Approximate tape remaining time appears on the display.
“– h – – m” means the camcorder is calculating the
remaining time. When the remaining time reaches
2 minutes, the indication starts blinking.
2 Open the LCD monitor fully. (See the right column)
3 Set the Power Switch to “A” or “M” while pressing
down the Lock Button located on the switch.
● The POWER/CHARGE lamp lights and the camcorder
enters the Record-Standby mode. “PAUSE” is displayed.
● To record in LP (Long Play) mode, ੬ pg. 14, 15.
0
h
25
m
4 To start recording, press the Recording Start/Stop
Button. The “T REC” appears on the display while
recording is in progress.
–h––m
(Now calculating)
1h 0m
0h59m
0h 1m
0h 3m
5 To stop recording, press the Recording Start/Stop
Button again. The camcorder re-enters the Record-
Standby mode.
0h 2m
NOTES:
(Blinking)
(Blinking)
(Blinking)
● The image will not appear simultaneously on the LCD
monitor and the viewfinder.
Zooming
● If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the viewfinder
again or close and re-open the LCD monitor.
● LCD monitor/viewfinder indications:
• When power is supplied from a battery: the “
battery indicator is displayed. (੬ pg. 31)
• When power is supplied from an AC outlet: the “
battery indicator does not appear.
● When a blank portion is left between recorded scenes on
the tape, the time code is interrupted and errors may occur
when editing the tape. To avoid this, refer to “Recording
From The Middle Of A Tape” (੬ pg. 11).
Produces the zoom in/out effect, or an instantaneous
change in image magnification.
Zoom In
”
Slide the Power Zoom Lever towards “T”.
Zoom Out
”
Slide the Power Zoom Lever towards “W”.
● The further you slide the Power Zoom Lever, the quicker the
zoom action.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO RECORDING EN
11
If recording starts from a blank portion, the time code
Zoom in (T: Telephoto)
begins counting from “00:00:00” (minute:second:frame).
If recording starts from the end of a previously recorded
scene, the time code continues from the last time code
number.
If during recording a blank portion is left partway through
the tape, the time code is interrupted. When recording is
resumed, the time code starts counting up again from
“00:00:00”. This means the camcorder may record the
same time codes as those existing in a previously
recorded scene. To prevent this, perform “Recording
cases;
● When shooting again after playing back a recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during shooting.
● When shooting using a partially recorded tape.
the tape.
1
x
W
T
10
x
W
T
20
x
W
T
40
xW
T
Zoom out (W: Wide angle)
10
x
W
T
Digital zoom zone
16X zoom zone
Approximate zoom ratio
● When shooting again after shooting a scene then opening/
closing the cassette holder cover.
NOTES:
● Focusing may become unstable during Zooming. In this
case, set the zoom while in Record-Standby, lock the focus
by using the manual focus (੬ pg. 21), then zoom in or out
in Record mode.
Recording From The Middle Of A Tape
1) Play back a tape or use Blank Search (੬ pg. 12) to
find the spot at which you want to start recording, then
engage the Still Playback mode. (੬ pg. 12)
2) Set the Power Switch to “A” or “M” while pressing
down the Lock Button located on the switch, then start
recording.
●
Zoomingispossibletoamaximumof700X,oritcanbeswitched
to 16X magnification using the optical zoom. ( pg. 15)
੬
● Zoom magnification of over 16X is done through Digital
image processing, and is therefore called Digital Zoom.
● During Digital zoom, the quality of image may suffer.
● Macro shooting (as close as approx. 5 cm to the subject) is
possiblewhenthePowerZoomLeverissetallthewayto“W”.
Also see “TELE MACRO” in MANUAL Menu on page 15.
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time code
indication does not move smoothly.
● The time code is displayed only when “TIME CODE” is set
to “ON”. (੬ pg. 16)
Journalistic Shooting
In some situations, different
shooting angles may provide
more dramatic results. Hold the
camcorder in the desired position
and tilt the LCD monitor in the
most convenient direction. It can
rotate 270° (90° downward, 180°
upward).
When a blank portion is recorded on a tape
Time code
00:00:00
Time code Time code
05:43:21 00:00:00
Already
recorded scene
Newlyrecorded
scene
Blank
Tape
Self Recording
Shooting start Shooting stop Shooting start
Open the LCD monitor and tilt
it upward to 180° so that it
faces forward, then point the
lens toward yourself and start
point
point
point
Proper recording
recording.
Self Recording
Time code
00:00:00
Time code Time code
05:43:21 05:44:00
Time Code
During recording, a time code is recorded on the tape.
This code is to confirm the location of the recorded scene
on the tape during playback.
Already
recorded scene
New
scene
Tape
Latest scene
Display
Shooting start Shooting start Shooting start
point point point
Minutes
Seconds
Frames*
(25 frames = 1 second)
12 : 34 : 24
* Frames are not displayed during recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN VIDEO PLAYBACK
12
Shuttle Search
MMENU/VOL.
BLANK SEARCH
Allows high-speed search in either direction during video
playback.
1) During playback, press 5 for forward search, or
3 for reverse search.
2) To resume normal playback, press 4/9.
● During playback, press and hold 5 or 3. The search
continues as long as you hold the button. Once you release
the button, normal playback resumes.
Search. This is not a malfunction.
ATTENTION:
During Shuttle Search, parts of the
picture may not be clearly visible,
particularly on the left side of the
screen.
Power Switch
Lock Button
8
4/9
Blank Search
Helps you find where you should start recording in the
middle of a tape to avoid time code interruption.
(੬ pg. 11)
1 Load a cassette. (੬ pg. 9)
2 Set the Power Switch to “PLAY” while pressing down
the Lock Button located on the switch.
3 During Stop mode, press BLANK SEARCH.
● The “BLANK SEARCH” indication appears and the
camcorder automatically starts reverse or forward search,
then stops at the spot which is about 3 seconds of tape
before the beginning of the detected blank portion.
● To cancel Blank Search midway, press 8.
3
5
Speaker
NOTES:
● Before starting Blank Search, if the current position is at a
blank portion, the camcorder searches in the reverse
direction. If the current position is at a recorded portion, the
camcorder searches in the forward direction.
● Blank Search does not work if “USE CLEANING
CASSETTE” has appeared with the tape.
Normal Playback
1 Load a cassette. (੬ pg. 9)
2 Set the Power Switch to “PLAY” while pressing down
the Lock Button located on the switch.
● If the beginning or end of the tape is reached during Blank
Search, the camcorder stops automatically.
● A blank portion which is shorter than 5 seconds of tape
may not be detected.
● The detected blank portion may be located between
recorded scenes. Before you start recording, make sure
there is no recorded scene after the blank portion.
3 To start playback, press 4/9.
4 To stop playback, press 8.
● During Stop mode, press 3 to rewind, or 5 to fast-
forward the tape.
To control the speaker volume
Rotate the MMENU/VOL. Wheel towards “+” to turn up
the volume, or towards “–” to turn down the volume.
NOTES:
● The playback picture can be viewed in the LCD monitor,
viewfinder or on a connected TV. (੬ pg. 13)
● For other notes, ੬ pg. 27.
Still Playback
Pauses during video playback.
1) Press 4/9 during playback.
2) To resume normal playback, press 4/9 again.
● If still playback continues for more than about 3 minutes,
the camcorder’s Stop mode is automatically engaged.
● When 4/9 is pressed, the image may not pause
immediately while the camcorder stabilises the still image.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO PLAYBACK EN
13
1 Make sure all units are turned off.
Connections To A TV Or VCR
These are some basic types of connections. When
making the connections, refer also to your VCR and TV
instruction manuals.
2 Connect the camcorder to a TV or VCR as shown in
the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
3 Connect the VCR output to the TV input, referring to
your VCR’s instruction manual.
4 Turn on the camcorder, the VCR and the TV.
5 Set the VCR to its AUX input mode, and set the TV to
its VIDEO mode.
To choose whether or not the following displays
appear on the connected TV
● Date/Time
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”. (੬ pg. 14, 17)
● Time Code
To AV
To S
Set “TIME CODE” to “ON” or “OFF”. (੬ pg. 14, 17)
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
(੬ pg. 14, 17)
Audio/Video
cable
(provided)
S-Video cable
(optional)
NOTES:
● It is recommended to use the AC Adapter as the power
supply instead of the battery pack. (੬ pg. 7)
● To monitor the picture and sound from the camcorder
without inserting a tape, set the camcorder’s Power Switch
to “A” or “M”, then set your TV to the appropriate input
mode.
1
2
3
4
● Make sure you adjust the TV sound volume to its minimum
level to avoid a sudden burst of sound when the camcorder
is turned on.
● If you have a TV or speakers that are not specially shielded,
do not place the speakers adjacent to the TV as
interference will occur in the camcorder playback picture.
● When a cable is connected to the AV connector, the sound
is not heard from the speaker.
Cable Adapter*
“Y/C”/“CVBS”Video
Out Select Switch
To TV or VCR
TV
VCR
A White to AUDIO L IN**
B Red to AUDIO R IN**
C Yellow to VIDEO IN
D To S-VIDEO IN***
*
If your VCR has a SCART connector, use the provided
cable adapter.
** Not required for watching still images only.
*** Connect when your TV/VCR has S-VIDEO IN and A/V
input connectors. In this case, it is not necessary to
connect the yellow video cable.
NOTE:
Set the video out select switch of the cable adapter as
required:
Y/C: When connecting to a TV or VCR which accepts Y/
C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which does not
accept Y/C signals and uses an audio/video cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN MENUS FOR DETAILED ADJUSTMENT
14
Menus without Sub Menus
Changing The Menu Settings
This camcorder is equipped with an easy-to-use, on-
screen menu system that simplifies many of the more
detailed camcorder settings. (੬ pg. 15 – 17)
v WIPE/FADER (੬ pg. 19)
r PROGRAM AE (੬ pg. 19)
p EXPOSURE (੬ pg. 22)
u W. BALANCE (੬ pg. 23)
Selected menu icon
blinks.
Selected
parameter
PROGRAM AE
1) Rotate the MMENU/VOL.
Wheel to select the desired
parameter.
● Example: r PROGRAM AE
Menu
Wheel in. Selection is complete.
The Menu Screen returns.
● Repeat the procedure if you wish
to set other function menus.
3) Press the MMENU/VOL.
Wheel in again. The Menu Screen
closes.
MMENU/VOL.
SHUTTER
TWILIGHT
SEPIA
Power Switch
Lock Button
MONOTONE
m CAMERA (੬ pg. 15)
q MANUAL (੬ pg. 15)
s SYSTEM (੬ pg. 16)
n CAMERA DISPLAY
(੬ pg. 16)
Selected menu icon
blinks.
Selected function
CAMERA
REC MODE
–
t VIDEO (੬ pg. 17)
SOUND MODE– 1 2b i
t
ZOOM
SNAP MODE
GA I N UP
–
–
–
4 0 x
1 For Video Recording Menus:
n VIDEO DISPLAY (੬ pg. 17)
1) Rotate the MMENU/VOL.
Wheel to select the desired
function, and press it. The Sub
Menu appears.
FULL
AUTO
A
Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
For Video Playback Menus:
RETURN
Set the Power Switch to “PLAY” while pressing down the
Lock Button located on the switch.
● Example: m CAMERA Menu
2) Rotate the MMENU/VOL.
Wheel to select the desired
parameter.
3) Press the MMENU/VOL.
Wheel in. Selection is complete.
● Repeat the procedure if you wish
to set other function menus.
4) Press the MMENU/VOL.
Wheel in. The Menu Screen
returns.
● Repeat the procedure if you wish
to set other function menus.
5) Press the MMENU/VOL.
Wheel in again. The Menu
Screen closes.
Sub Menu
CAMERA
REC MODE
2 Open the LCD monitor fully. (੬ pg. 10)
–
3 Press the MMENU/VOL. Wheel in. The Menu Screen
appears.
4 Rotate the MMENU/VOL. Wheel to select the desired
function, and press it. The selected function menu
appears.
RETURN
CAMERA
REC MODE
–
Screen for Video
Recording Menu
Screen for Video
Playback Menu
SOUND MODE– 1 2b i
t
ZOOM
–
–
–
4 0 x
SNAP MODE
GA I N UP
FULL
AUTO
WI PE / FADER
OFF
FADER–WH I TE
FADER–BLACK
FADER–B .W
V I DEO
A
SOUND MODE– STEREO
NARRAT I ON
REC MODE
–
–
OFF
WI PE–CORNER
WI PE–WI NDOW
WI PE–SL I DE
WI PE–DOOR
RETURN
WI PE–SCROLL
WI PE–SHUTTER
RETURN
5 Setting procedure hereafter depends on the selected
function.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT EN
15
AGC mode, but the subject’s movements are not smooth
or natural. The overall appearance may be grainy. While
Recording Menus
the shutter speed is being automatically adjusted, “
is displayed.
”
CAMERA
The “m” settings are effective when the Power Switch is
set to both “A” and “M”. However, the menu settings can
be changed only when the Power Switch is set to “M”.
[ ] = Factory-preset
MANUAL
The “q” settings are effective only when the Power
Switch is set to “M”.
[ ] = Factory-preset
REC MODE
DIS
[SP]: To record in the SP (Standard Play) mode
LP: Long Play—more economical, providing 1.5 times
the recording time.
OFF: Disables the function.
]: To compensate for unstable images caused
by camera-shake, particularly at high magnification.
[ON
NOTES:
NOTES:
● If the recording mode is switched, the playback picture will
be blurred at the switching point.
● Accurate stabilisation may not be possible if hand shake is
excessive, or under the following conditions:
• When shooting subjects with vertical or horizontal stripes.
• When shooting dark or dim subjects.
• When shooting subjects with excessive backlighting.
• When shooting scenes with movement in various
directions.
• When shooting scenes with low-contrast backgrounds.
● Switch off this mode when recording with the camcorder on
a tripod.
● It is recommended that tapes recorded in the LP mode on
this camcorder be played back on this camcorder.
● During playback of a tape recorded on another camcorder,
blocks of noise may appear or there may be momentary
pauses in the sound.
SOUND MODE
[12 bit]: Enables video recording of stereo sound on four
separate channels, and is recommended for use when
performing Audio Dubbing. (Equivalent to the 32 kHz
mode of previous models)
● The “
cannot be used.
” indicator blinks or goes out if the Stabiliser
16 bit: Enables video recording of stereo sound on two
separate channels. (Equivalent to the 48 kHz mode of
previous models)
TELE MACRO
[OFF]: Disables the function.
ON: Usually the distance to a subject where the lens is in
focus depends on the zoom magnification. Unless there
is a distance more than 1 m to the subject, the lens is out
of focus at the maximum telephoto setting. When set to
“ON”, you can shoot a subject as large as possible at a
distance of approx. 60 cm.
ZOOM
16X: When set to “16X” while using digital zoom, the
zoom magnification will reset to 16X since digital zoom
will be disengaged.
[40X]: Allows you to use the Digital Zoom. By digitally
processing and magnifying images, zooming is possible
from 16X (the optical zoom limit), to a maximum of 40X
digital magnification.
NOTE:
Depending on the zoom position, the lens may go out of
focus.
700X: Allows you to use the Digital Zoom. By digitally
processing and magnifying images, zooming is possible
WIDE MODE
from 16X (the optical zoom limit), to a maximum of 700X [OFF]: Records with no change in the screen ratio. For
digital magnification.
playback on a TV with a normal screen ratio.
CINEMA : Inserts black bands at the top and bottom of
SNAP MODE
the screen. The
indicator appears. During playback
on wide-screen TVs, the black bands at the top and
bottom of the screen are cut and the screen ratio
becomes 16:9. When using this mode, refer to your wide-
screen TV’s instruction manual. During playback/
recording on 4:3 TVs/LCD monitor/viewfinder, black
bands are inserted at the top and bottom of the screen
and the image appears like a letter boxed 16:9 movie.
SQUEEZE : For playback on TVs with an aspect ratio
of 16:9. Naturally expands the image to fit the screen
[FULL]: Snapshot mode with no frame
PIN-UP: Pin-Up mode
FRAME: Snapshot mode with frame
[FULL]
PIN-UP
FRAME
For details on the procedure, refer to “Snapshot (For
Video Recording)” (੬ pg. 20).
without distortion. The
indicator appears. When using
this mode, refer to your wide-screen TV’s instruction
manual. During playback/recording on 4:3 TVs/LCD
monitor/viewfinder, the image is elongated vertically.
GAIN UP
OFF: Allows you to shoot dark scenes with no picture
brightness adjustment.
[AGC]: The overall appearance may be grainy, but the
image is bright.
AUTO
adjusted. Shooting a subject in low or poor lighting at
slow shutter speed provides a brighter image than in the
WIND CUT
[OFF]: Disengages the function.
ON
“
: Helps cut down on noise created by wind. The
” indicator appears. The quality of the sound will
: The shutter speed is automatically
change. This is normal.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN MENUS FOR DETAILED ADJUSTMENT
16
SYSTEM
CAMERA DISPLAY
● The “n” (CAMERA DISPLAY) settings are effective even
when the Power Switch is set to “A”. However, the menu
settings can be changed only when the Power Switch is set
to “M”.
● The “n” (CAMERA DISPLAY) settings are effective only
for shooting except “BRIGHT”.
The “s” functions which are set when the Power Switch
set to “PLAY”.
[ ] = Factory-preset
BEEP
[ ] = Factory-preset
OFF: Turns off sounds when performing any operations.
It also deactivates the shutter sound effect, however the
shutter sound is recorded onto the tape during Snapshot
for Video Recording (੬ pg. 20).
BRIGHT
੬ pg. 9, “Brightness Adjustment Of The Display”
BEEP: The beep sounds when the power is turned on or
off, and at the beginning and end of recording. It also
activates the shutter sound effect. (੬ pg. 20)
[MELODY]: Instead of a beep, a melody sounds when
any operation is performed. It also activates the shutter
sound effect. (੬ pg. 20)
ON SCREEN
LCD: Keeps the camcorder’s display (except the date,
time and time code) from appearing on the connected TV
screen.
[LCD/TV]: Makes the camcorder’s display appear on
screen when the camcorder is connected to a TV.
DEMO MODE
DATE/TIME
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as Program
AE with special effects, etc., and can be used to confirm
how these functions operate. Demonstration starts in the
following cases:
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5 seconds
when the Power Switch is set from “OFF” to “A” or “M”.
ON: The date/time is always displayed.
● When the Menu Screen is closed after “DEMO MODE” is
turned “ON”.
TIME CODE
● With “DEMO MODE” set to “ON”, if there is no operation for
about 3 minutes after the Power Switch is set to “A” or “M”.
Performing any operation during the demonstration stops
the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder and on the
connected TV. Frame numbers are not displayed during
recording. (੬ pg. 11)
CLOCK ADJ.
੬ pg. 8, “Date/Time Settings”
NOTES:
● If a cassette is in the camcorder, the demonstration cannot
be turned on.
● “DEMO MODE” remains “ON” even if the camcorder power
is turned off.
● If “DEMO MODE” remains “ON”, some functions will not be
available. After viewing demo, set to “OFF”.
PRIORITY
[LCD]: The image is displayed on the LCD monitor when
the viewfinder is pulled out while the LCD monitor is
opened.
FINDER: The image is displayed in the viewfinder when
the viewfinder is pulled out while the LCD monitor is
opened.
CAM RESET
EXECUTE: Resets all settings to the factory-preset.
RETURN: Does not reset all settings to the factory-
preset.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT EN
17
SYSTEM
Playback Menus
Each setting is linked with “s”, which appears when the
Power Switch is set to “M”. (੬ pg. 14)
● The parameters are the same as in the description on
page 16.
VIDEO
[ ] = Factory-preset
[ ] = Factory-preset
SOUND MODE and NARRATION
During tape playback, the camcorder detects the sound
mode in which the recording was made, and plays the
sound back. Select the type of sound to accompany your
playback picture. According to the menu access
explanation on page 14, select “SOUND MODE” or
“NARRATION” from the Menu Screen and set it to the
desired parameter.
BEEP
OFF / BEEP / [MELODY]
OFF / [ON]
DEMO MODE
PRIORITY
CAM RESET
[LCD] / FINDER
EXECUTE / RETURN
VIDEO DISPLAY
SOUND MODE
The “n” (VIDEO DISPLAY) settings are effective only for
video playback except “BRIGHT”.
● The parameters (except “OFF” in ON SCREEN settings)
are the same as in the description on page 16.
[ ] = Factory-preset
[STEREO
channels in stereo.
SOUND L : Sound from the “L” channel is output.
SOUND R : Sound from the “R” channel is output.
]: Sound is output on both “L” and “R”
NARRATION
BRIGHT
[OFF]: Original sound is output on both “L” and “R”
channels in stereo.
੬ pg. 9, “Brightness Adjustment Of The Display”
ON: Dubbed sound is output on both “L” and “R”
channels in stereo.
MIX: Original and dubbed sounds are combined and
output in stereo on both “L” and “R” channels.
ON SCREEN
When set to “OFF”, the camcorder’s display disappears.
DATE/TIME [OFF] / AUTO / ON
OFF / [LCD] / LCD/TV
NOTES:
When set to “AUTO”, the date/time are displayed in the
following cases:
● When playback starts. The camcorder displays the date/
time when scenes are recorded.
● The “SOUND MODE” setting is available for both 12-bit and
16-bit sound. (In previous models’ functions, “12-bit” is
called “32 kHz” and “16-bit” is called “48 kHz”.)
● The camcorder cannot detect the sound mode in which the
recording was made during fast-forward or rewind. During
playback the sound mode is displayed in the upper left
corner.
● When the date is changed during playback.
TIME CODE
[OFF] / ON
REC MODE
[SP] / LP
Allows you to set the video recording mode (SP or LP)
depending on your preference. It is recommended you
use “REC MODE” in VIDEO Menu when using this
camcorder as a recorder during dubbing. (੬ pg. 25)
NOTE:
“REC MODE” can be set when the Power Switch is set to
“PLAY” or “M”.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN FEATURES FOR RECORDING
18
SNAPSHOT
Power Switch
Night Scope
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is
strobing due to the slow shutter speed.
Lock Button
Recording Start/Stop Button
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
3 Press NIGHT so that the Night-Scope indicator “
”
appears.
● The shutter speed is automatically adjusted to provide up to
LIGHT
30 times sensitivity.
● “ ” appears beside “
” while the shutter speed is being
automatically adjusted.
NIGHT
To deactivate Night-Scope
Press NIGHT again so that the Night-Scope indicator
disappears.
White LED Light
NOTES:
● During Night-Scope, the following functions or settings
cannot be activated and its indicator blinks or goes out:
• Some modes of “Program AE With Special Effects”
(੬ pg. 19).
• “GAIN UP” in CAMERA Menu. (੬ pg. 15)
• “DIS” in MANUAL Menu. (੬ pg. 15)
● During Night-Scope, it may be difficult to bring the
camcorder into focus. To prevent this, use of a tripod is
recommended.
White LED Light
White LED Light can be used to brighten the subject in
the dark place during video recording.
1 Press LIGHT repeatedly to change the setting.
OFF: Turns off the light.
ON: The light is on always. (
AUTO: The light turns on automatically when dark.
appears.)
appears.)
(
2 Press the Recording Start/Stop Button to start video
recording or SNAPSHOT to shoot a still image.
NOTES:
● Be careful not to point the LED Light directly to eyes.
● If the light does not reach the subject, the Night-Scope
function will be activated, and makes it possible to shoot
the subject brighter.
● There is a difference in the brightness of the images shot
between the centre area which is illuminated by the LED
Light and the surrounding areas (which will be darker).
● Since subjects are shot at a reduced shutter speed when
the White LED Light setting is “ON”, they will appear slightly
blurred.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING EN
19
WIPE–CORNER: Wipe in on a black screen from
the upper right to the lower left corner, or wipe out from
lower left to upper right, leaving a black screen.
SNAPSHOT
MMENU/VOL.
Power Switch
WIPE–WINDOW: The scene starts in the centre of
a black screen and wipes in toward the corners, or
comes in from the corners, gradually wiping out to the
centre.
Lock Button
WIPE–SLIDE: Wipe in from right to left, or wipe out
from left to right.
WIPE–DOOR: Wipe in as the two halves of a black
screen open to the left and right, revealing the scene, or
wipe out and the black screen reappears from left and
right to cover the scene.
WIPE–SCROLL: The scene wipes in from the
bottom to the top of a black screen, or wipes out from top
to bottom, leaving a black screen.
WIPE–SHUTTER: Wipe in from the centre of a
black screen toward the top and bottom, or wipe out from
the top and bottom toward the centre leaving a black
screen.
Wipe Or Fader Effects
IMPORTANT:
Some Wipe/Fader Effects cannot be used with certain modes
of Program AE with special effects. (See the right column.) If
an unusable Wipe/Fader Effect is selected, its indicator blinks
in blue or goes out.
IMPORTANT:
Some modes of Program AE with special effects cannot be
used with certain Wipe/Fader effects. (See the left column.) If
an unusable mode is selected, the indicator of Program AE
with Special Effects blinks or goes out.
These effects let you make pro-style scene transitions.
Use them to spice up the transition from one scene to the
next.
Wipe or Fader works when video recording is started or
stopped.
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
3 Set “r” to the desired mode. (੬ pg. 14)
● The PROGRAM AE menu disappears and the selected
effect is activated.
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
● The selected effect indicator appears.
3 Set “v” to the desired mode. (੬ pg. 14)
● The WIPE/FADER menu disappears and the effect is
reserved.
To deactivate the selected effect
Select “OFF” in step 3. The effect indicator disappears.
NOTES:
● The selected effect indicator appears.
● Program AE with special effects can be changed during
recording or during Record-Standby.
● Some modes of Program AE with special effects cannot be
used during Night-Scope.
4 Press the Recording Start/Stop Button to activate the
Fade-in/out or Wipe-in/out.
To deactivate the selected effect
Select “OFF” in step 3. The effect indicator disappears.
PROGRAM AE
NOTE:
You can extend the length of a Wipe or Fader by pressing and OFF: Disables the function. (Factory-preset)
holding the Recording Start/Stop Button.
SHUTTER 1/50: The shutter speed is fixed at 1/
50th of a second. Black bands that usually appear when
shooting a TV screen become narrower.
WIPE/FADER
SHUTTER 1/120: The shutter speed is fixed at 1/
120th of a second. The flickering that occurs when
shooting under a fluorescent light or mercury-vapour
lamp is reduced.
OFF: Disables the function. (Factory-preset)
FADER–WHITE: Fade in or out with a white
screen.
FADER–BLACK: Fade in or out with a black
screen.
SPORTS
(Variable Shutter Speed: 1/250 – 1/4000)
This setting allows fast-moving images to be captured
one frame at a time, for vivid, stable slow-motion
playback. The faster the shutter speed, the darker the
picture becomes. Use the shutter function under good
lighting conditions.
FADER–B.W: Fade in to a colour screen from a
black and white screen, or fade out from colour to black
and white.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN FEATURES FOR RECORDING
20
● When a cable is connected to the AV connector, the shutter
sound is not heard from the speaker, however it is recorded
onto the tape.
SNOW: Compensates for subjects that may
otherwise appear too dark when shooting in extremely
bright surroundings such as in the snow.
SPOTLIGHT: Compensates for subjects that may
otherwise appear too bright when shooting under
extremely strong direct lighting such as spotlights.
Motor Drive Mode
Keeping SNAPSHOT pressed in step 4 provides an
effect similar to serial photography. (Interval between still
images: approx. 1 second)
NOTE:
“SPOTLIGHT” has the same effect as –3 with the exposure
control. (੬ pg. 22)
TWILIGHT: Makes evening scenes look more
natural. White Balance (੬ pg. 23) is automatically set to
“
”, but can be changed to your desired setting. When
Twilight is chosen, the camcorder automatically adjusts
the focus from approx. 10 m to infinity. From less than 10
m, adjust the focus manually.
SEPIA: Recorded scenes have a brownish tint like
old photos. Combine this with the Cinema mode for a
classic look.
MONOTONE: Like classic black and white films,
your footage is shot in B/W. Used together with the
Cinema mode, it enhances the “classic film” effect.
CLASSIC FILM: Gives recorded scenes a strobe
effect.
STROBE: Your recording looks like a series of
consecutive snapshots.
Snapshot (For Video Recording)
This feature lets you record still images that look like
photographs onto a tape.
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
3 Set “SNAP MODE” to the desired mode.
(੬ pg. 14, 15)
4 Press SNAPSHOT.
● There is the sound effect of a shutter closing.
● The “O” indication appears and a still image will be
recorded for approx. 6 seconds, then the camcorder re-
enters the Record-Standby mode.
● You can perform Snapshot also during recording. A still
normal recording resumes.
● Regardless of the Power Switch position (“A” or “M”),
Snapshot recording takes place using the selected
Snapshot mode.
NOTES:
● To remove the shutter sound, refer to “BEEP” on page 16.
● When “WIDE MODE” is set to “SQUEEZE
” (੬ pg. 15),
the “O” indication blinks in blue and Snapshot recording
becomes impossible.
● If Program AE with special effects (੬ pg. 19) is engaged,
certain modes of Program AE with special effects are
disabled during Snapshot recording. In such a case, the
icon blinks.
● If SNAPSHOT is pressed when “DIS” is set to “ON”
(੬ pg. 15), the Stabiliser will be disabled.
● During Snapshot recording, the image displayed in the
viewfinder may be partially missing. However, there is no
effect in the recorded image.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING EN
21
FOCUS
Manual Focus
SNAPSHOT
NOTE:
If you are using the viewfinder, you should already have
performed “Viewfinder Adjustment” (੬ pg. 8).
MMENU/VOL.
1 Set the Power Switch to “M”
While focusing on a
further subject
while pressing down the Lock
Button located on the switch.
Lock Button
2 Press FOCUS. The manual
focus indicator appears.
3 To focus on a further subject,
rotate the MMENU/VOL. Wheel
towards “+”. The “ ” indicator
appears and blinks.
Manual focus indicator
To focus on a nearer subject,
rotate the MMENU/VOL. Wheel
towards “–”. The “ ” indicator
appears and blinks.
While focusing on a
nearer subject
Auto Focus
The camcorder’s Full Range AF
system offers continuous shooting
ability from close-up (as close as
approx. 5 cm to the subject) to
infinity.
To reset to Auto Focus
Press FOCUS twice or set the
Power Switch to “A”.
If FOCUS is pressed once, the
camcorder will enter the focus
adjustment mode again.
However, correct focus may not be
obtainable in the situations listed
below (in these cases perform
“Manual Focus”):
● When two subjects overlap in the
same scene.
Manual focus indicator
Focus detection zone
NOTES:
● Be sure to focus the lens in the maximum telephoto position
when you use the Manual Focus mode. If you focus in on a
subject in the wide-angle position, sharply focused images
cannot be obtained when zoomed up because the depth-
of-field is reduced at longer focal lengths.
● When illumination is low.*
● When the subject has no contrast (difference in brightness
and darkness), such as a flat, one-colour wall, or a clear,
blue sky.*
the viewfinder.*
● When the focus level cannot be adjusted any further or
closer, “ ” or “ ” will blink.
● When the scene contains minute patterns or identical
patterns that are regularly repeated.
● When the scene is affected by sunbeams or light reflecting
off the surface of a body of water.
● When shooting a scene with a high-contrast background.
* The following low-contrast warnings appear blinking:
,
,
and
NOTES:
● If the lens is smeared or blurred, accurate focusing is not
possible. Keep the lens clean. (੬ pg. 34) When
condensation occurs, wipe with a soft cloth or wait for it to
dry naturally.
● When shooting a subject close to the lens, zoom out first.
(੬ pg. 10) If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out depending on the
distance between the camcorder and the subject. This will
not occur when “TELE MACRO” is set to “ON”. (੬ pg. 15)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN FEATURES FOR RECORDING
22
Exposure Control
Iris Lock
Manual exposure control is recommended in the
following situations:
● When shooting using reverse lighting or when the
background is too bright.
● When shooting on a reflective natural background such as
at the beach or when skiing.
Like the pupil of the human eye, the iris contracts in well-
and dilates in dim environments to allow in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so its size in the
LCD monitor or the viewfinder changes), such as when the
subject is backing away.
● When shooting on a reflective natural background such as
at the beach or when skiing.
● When shooting objects under a spotlight.
● When zooming.
● When the background is overly dark or the subject is bright.
1 Set the Power Switch to “M” while pressing down the
Lock Button located on the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
3 Press the MMENU/VOL. Wheel in. The Menu Screen
appears.
When the subject is close, keep the iris locked. Even
when the subject moves away from you, the image will
not darken or brighten.
“Exposure Control”.
4 Rotate the MMENU/VOL. Wheel to select
“p (EXPOSURE)”, and press it.
5 Rotate the MMENU/VOL. Wheel to select “MANUAL”,
and press it.
● The exposure control indicator appears.
6 Adjust zoom so that the subject fills the LCD monitor
or the viewfinder, then press and hold the MMENU/VOL.
and the “ ” indication appear.
6 To brighten the image, rotate the MMENU/VOL.
MMENU/VOL. Wheel towards “–”. (maximum 6)
● +3 exposure has the same effect as the backlight
compensation. (੬ pg. 23)
in. The “ ” indication changes to
“
” and the iris is locked.
● –3 exposure has the same effect as when “r” is set to
3
“SPOTLIGHT”. (੬ pg. 20)
To return to automatic iris
control
Rotate the MMENU/VOL. Wheel
to select “AUTO”, then press it in
step 5. Or, set the Power Switch to
“A”.
7 Press the MMENU/VOL. Wheel in. Exposure
adjustment is complete.
Iris Lock Indicator
To return to automatic exposure control
Select “AUTO” in step 5. Or, set the Power Switch to “A”.
NOTES:
● The exposure control indicator and “ ” disappear.
● You cannot use the manual exposure control at the same
time when “r” is set to “SPOTLIGHT” or “SNOW”
(੬ pg. 19), or with the backlight compensation. (੬ pg. 23)
● If the adjustment does not cause any visible change in
brightness, set “GAIN UP” to “AUTO”. (੬ pg. 14, 15)
To lock the exposure control and the iris
After step 5 of “Exposure Control”, adjust the exposure
by rotating the MMENU/VOL. Wheel. Then lock the iris in
steps 6 and 7 of “Iris Lock”. For automatic locking, rotate
the MMENU/VOL. Wheel to select “AUTO”, then press it
in step 5. The exposure control and the iris become
automatic.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING EN
Backlight Compensation
Manual White Balance Adjustment
Backlight compensation
brightens the subject quickly.
Press BACKLIGHT. The
indicator is displayed and the
subject is brightened. If
pressed again,
Adjust the white balance
manually when shooting
under various types of
lighting.
1 Set the Power Switch to
“M” while pressing down
the Lock Button located on
disappears and the
BACKLIGHT Button
White paper
brightness returns to the
previous level.
● Using the BACKLIGHT
Button may cause the light around the subject to become
too bright and the subject to become white.
● Backlight compensations is also available when the Power
Switch is set to “A”.
the switch.
2 Open the LCD monitor fully. (੬ pg. 10)
3 Set “u” to “MWB”. (੬ pg. 14)
indication blinks slowly.
4 Hold a sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so that the
white paper fills the screen.
White Balance Adjustment
begins
blinking rapidly.
The white balance that refers to the correctness of colour
reproduction under various lighting. If the white balance
is correct, all other colours will be accurately reproduced.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators control
this function manually to achieve a more professional
colour/tint reproduction.
● When the setting is completed,
resumes normal
blinking.
6 Press the MMENU/VOL. Wheel in twice. The Menu
Screen closes and the Manual White Balance indicator
is displayed.
NOTES:
● In step 4, it may be difficult to focus on the white paper. In
such a case, adjust focus manually. (੬ pg. 21)
● A subject can be shot under various types of lighting
conditions indoors (natural, fluorescent, candlelight, etc.).
Because the colour temperature is different depending on
the light source, the subject tint will differ depending on the
white balance settings. Use this function for a more natural
result.
To change the setting
Set “u” to the desired mode. (੬ pg. 14)
● The selected mode indicator except “AUTO” appears.
[AUTO]: White balance is adjusted automatically.
shooting under various types of lighting. (੬ “Manual
White Balance Adjustment”)
● Once you adjust white balance manually, the setting is
retained even if the power is turned off or the battery
removed.
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
HALOGEN: A video light or similar type of lighting
is used.
[ ] = Factory-preset
To return to automatic white balance
Set “u” to “AUTO”. (੬ pg. 14)
Or, set the Power Switch to “A”.
NOTE:
White balance cannot be used when “r” is set to “SEPIA” or
“MONOTONE”. (੬ pg. 20)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN EDITING
24
Dubbing To A VCR
To use this camcorder as a player
1 Following the illustrations, connect the camcorder and
the VCR. Also refer to page 13.
2 Set the camcorder’s Power Switch to “PLAY” while
3 Turn on the VCR’s power.
4 Insert the source cassette in the camcorder.
5 Insert the recording cassette in the VCR.
6 Engage the VCR’s AUX and Record-Pause modes.
● Refer to the instruction manual for the VCR.
7 Press 4/9 on the camcorder to start playback of the
source tape.
8 At the point you want to start dubbing, engage the
To AV
To S
VCR’s Record mode.
Audio/Video
cable
(provided)
S-Video cable
(optional)
9 To pause dubbing, engage the VCR’s Record-Pause
mode and press 4/9 on the camcorder.
VCR and camcorder.
NOTES:
● It is recommended to use the AC Adapter as the power
supply instead of the battery pack. (੬ pg. 7)
on your TV. This will confirm the connections and the AUX
channel for dubbing purposes.
1
2
3
4
● Before you start dubbing, make sure that the indications do
not appear on the connected TV. If they do, they are being
recorded onto the new tape.
To choose whether or not the following displays appear
on the connected TV
Cable Adapter*
“Y/C”/“CVBS”Video
Out Select Switch
• Date/time
To TV or VCR
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 14, 17)
• Time code
TV
Set “TIME CODE” to “OFF” or “ON”. (੬ pg. 14, 17)
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
(੬ pg. 14, 17)
VCR
A White to AUDIO L IN
B Red to AUDIO R IN
C Yellow to VIDEO IN
D To S-VIDEO IN**
*
If your VCR has a SCART connector, use the provided
cable adapter.
** Connect when your TV/VCR has an S-VIDEO IN
connector. In this case, it is not necessary to connect the
yellow video cable.
NOTE:
Set the video out select switch of the cable adapter as
required:
Y/C: When connecting to a TV or VCR which accepts Y/
C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which does not
accept Y/C signals and uses an audio/video cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING EN
25
To use this camcorder as a player
Dubbing To A Video Unit Equipped With A
DV Connector (Digital Dubbing)
It is also possible to copy recorded scenes from the
camcorder onto another video unit equipped with a DV
connector. Since a digital signal is sent, there is little if
any image or sound deterioration.
1 Make sure all units are turned off.
2 Connect this camcorder to a video unit equipped with
a DV input connector using a DV cable as shown in the
illustration.
3 Set this camcorder’s Power Switch to “PLAY” while
pressing down the Lock Button located on the switch.
4 Turn on the video unit’s power.
5 Insert the source cassette in this camcorder.
6 Insert the recording cassette in the video unit.
7 Press 4/9 on this camcorder to start playback of the
source cassette.
8 At the point you want to start dubbing, engage the
video unit’s Record mode.
9 To pause dubbing, engage the video unit’s Record-
Pause mode and press 4/9 on this camcorder.
10 Repeat steps 7 – 9 for additional editing. Stop the
To DV OUT
video unit and camcorder.
NOTES:
supply instead of the battery pack. (੬ pg. 7)
● If a blank portion or disturbed image is played back on the
player during dubbing, the dubbing may stop so that an
unusual image is not dubbed.
DV cable
(optional)
Core filter
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 8. If this
occurs, turn off the power and make connections again.
● If SNAPSHOT is pressed during playback, only the original
playback image recorded on the tape is output from the DV
connector.
To DV IN
● When using a DV cable, be sure to use the optional
JVC VC-VDV204U DV cable.
Video unit equipped
with DV connector
Download from Www.Somanuals.com. All Manuals Search And Download.
EN EDITING
26
Connection To A Personal Computer
It is also possible to transfer still/moving images to a PC
with a DV connector by using the provided software,
software equipped with the PC or commercially available
software.
NOTES:
● Refer to “SOFTWARE INSTALLATION AND DV
CONNECTION GUIDE” for the installation of the bundled
software and drivers.
To DV OUT
● The software operation manual is provided as PDF file on
the CD-ROM.
● It is recommended to use the AC Adapter as the power
supply instead of the battery pack. (੬ pg. 7)
● When using a DV cable, be sure to use the optional
JVC VC-VDV206U or VC-VDV204U DV cable depending
on the type of DV connector (4 or 6 pins) on the PC.
● The date/time information cannot be captured into the PC.
● Refer to the instruction manuals of the PC and Software.
● The system may not work properly depending on the PC or
capture board you are using.
Core filter
DV cable (optional)
Core filter
To DV
connector
PC with DV
connector
Download from Www.Somanuals.com. All Manuals Search And Download.
27
● The time required to calculate and display the remaining
tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
Power (pg. 6)
● Perform charging where the temperature is between 10°C
and 35°C. 20°C to 25°C is the ideal temperature range for
charging. If the environment is too cold, charging may be
incomplete.
● Charging time is based on room temperature of 20°C.
● Charging times are for a fully discharged battery pack.
● Charging time varies according to the ambient temperature
and the status of the battery pack.
● To avoid interference with reception, do not use the AC
Adapter near a radio.
● Since the AC Adapter processes electricity internally, it
becomes warm during use. Be sure to use it only in well-
ventilated areas.
● “TAPE END” appears when the tape reaches its end, and
the power goes off automatically if left in this condition for 5
minutes. “TAPE END” also appears when a cassette at its
end is loaded.
VIDEO PLAYBACK (pg. 12)
cassette when:
• No picture during playback.
• Blocks of noise appear during playback.
For details, ੬ pg. 33.
● If Stop mode continues for 5 minutes when power is
supplied from a battery, the camcorder shuts off
automatically. To turn on again, set the Power Switch to
“OFF”, then to “PLAY”.
● You can also view the playback picture on the LCD monitor
with it flipped over and pushed against the camcorder body.
● LCD monitor/viewfinder indications:
● The following operation stops charging:
• Set the Power Switch to “PLAY”, “A” or “M”.
• Disconnect the AC Adapter from the camcorder.
• Unplug the AC Adapter from the AC outlet.
• Detach the battery from the camcorder.
● Using the optional AA-V40 AC Power Adapter/Charger, you
can charge the BN-V408U/V416U/V428U battery pack
without the camcorder. However, it cannot be used as an
AC Adapter.
• When power is supplied from a battery: the “
battery indicator is displayed. (੬ pg. 31)
• When power is supplied from an AC outlet: the “
battery indicator does not appear.
”
”
Loading/Unloading A Cassette (pg. 9)
● It takes a few seconds for the cassette holder to open. Do
not apply force.
● When a cable is connected to the AV connector, the sound
is not heard from the speaker.
● If you wait a few seconds and the cassette holder does not
open, close the cassette holder cover and try again. If the
cassette holder still does not open, turn the camcorder off
then on again.
● If the tape does not load properly, open the cassette holder
cover fully and remove the cassette. A few minutes later,
insert it again.
● When the camcorder is suddenly moved from a cold place
to a warm environment, wait a short time before opening
the cassette holder cover.
● Closing the cassette holder cover before the cassette
holder recedes may cause damage to the camcorder.
● Even when the camcorder is switched off, a cassette can
be loaded or unloaded. After the cassette holder is closed
with the camcorder switched off, however, it may not
recede. It is recommended to turn the power on before
loading or unloading.
● When resuming recording, once you open the cassette
holder cover a blank portion will be recorded on the tape or
a previously recorded scene will be erased (recorded over)
regardless of whether the cassette holder came out or not.
See “Recording From The Middle Of A Tape” (੬ pg. 11).
VIDEO RECORDING (pg. 10)
● When you use the LCD monitor outdoors in direct sunlight,
the LCD monitor may be difficult to see. If this happens, use
the viewfinder instead.
● The cassette holder cannot be opened unless a power
supply is attached.
● There may be a delay after you open the cassette holder
cover until the cassette holder opens. Do not use force.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
● When the Recording Start/Stop button is pressed, it may
take a few seconds before actual recording starts. The “T”
indicator starts rotating when the camcorder actually starts
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN TROUBLESHOOTING
28
If the problem still exists after following the steps below,
please consult your nearest JVC dealer.
During recording, the date/ time does not appear.
● “DATE/TIME” is set to “OFF”.
HSet “DATE/TIME” to “ON”. (੬ pg. 14, 16)
The camcorder is a microcomputer-controlled device.
might prevent it from functioning properly. In such
cases, first disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few minutes; and
then re-connect it and proceed as usual from the
beginning.
During recording, sound cannot be heard.
● This is normal.
The LCD monitor or viewfinder indications blink.
● Certain Wipe/Fader effects, certain modes of Program AE
with special effects, “DIS” and other functions that cannot
be used together are selected at the same time.
HRe-read the sections covering Wipe/Fader effects,
Program AE with special effects and “DIS”. (੬ pg. 14 – 20)
Power
No power is supplied.
● The power is not connected properly.
HConnect the AC Adapter securely. (੬ pg. 7)
● The battery is dead.
HReplace the dead battery with a fully charged one.
(੬ pg. 6, 7)
Digital Zoom does not work.
● 16X optical zoom is selected.
HSet “ZOOM” to “40X” or “700X”. (੬ pg. 15).
Coloured bright spots appear all over the LCD
monitor.
● The LCD monitor is not open fully or the viewfinder is not
pulled out when recording.
HOpen the LCD monitor fully or pull out the viewfinder.
● White spots or bright spots of light (red, green or blue) may
appear on the LCD monitor. This may occur when the
not a malfunction.
The POWER/CHARGE lamp blinks in the Record-
Standby mode.
● If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically.
Video Playback
Then, the POWER/CHARGE lamp will blink to indicate for
charging if the battery pack is attached to the camcorder
and its power is supplied from the AC Adapter.
HPush back and pull out the viewfinder again or close and
re-open the LCD monitor to return to the Record-Standby
mode.
Play, Rewind and Fast-Forward functions do not
work.
HSet the Power Switch to “PLAY”. (੬ pg. 12)
The tape is moving, but there is no picture.
Video Recording
● Your TV has AV input terminals, but is not set to its VIDEO
mode.
HSet the TV to the mode or channel appropriate for video
playback. (੬ pg. 13)
● The cassette holder cover is open.
HClose the cassette holder cover. (੬ pg. 9)
Recording cannot be performed.
● The Power Switch is set to “PLAY” or “OFF”.
HSet the Power Switch to “A” or “M”. (੬ pg. 10)
● The tape’s erase protection tab is set to “SAVE”.
HSet the tape’s erase protection tab to “REC”. (੬ pg. 9)
● “TAPE END” appears.
HReplace with new cassette. (੬ pg. 9)
● The cassette holder cover is open.
HClose the cassette holder cover.
Blocks of noise appear during playback, or there is
no playback picture and the screen becomes blue.
HClean the video heads with an optional cleaning cassette.
(੬ pg. 33)
When shooting a subject illuminated by bright light,
vertical lines appear.
● This is a result of exceedingly high contrast, and is not a
malfunction.
When the screen is under direct sunlight during
shooting, the screen becomes red or black for an
instant.
● This is not a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced features
Other problems
The focus does not adjust automatically.
The POWER/CHARGE lamp on the camcorder does
not light.
● Focus is set to the Manual mode.
HSet Focus to the Auto mode. (੬ pg. 21)
● The lens is dirty or covered with condensation.
HClean the lens and check the focus again. (੬ pg. 34)
● The recording was done in a dark place, or the contrast
was low.
● The temperature of the battery is extremely high/low.
● Charging is difficult in places subject to extremely high/low
temperatures.
HTo protect the battery, it is recommended to charge it in
places with a temperature of 10°C to 35°C. (੬ pg. 32)
Snapshot mode cannot be used.
“SET DATE/TIME!” appears.
● The Squeeze mode (SQUEEZE) is selected.
● The date/time is not set.
HSet the date/time. (੬ pg. 8)
● The built-in clock battery has run out and the previously set
date/time has been erased.
The colour of Snapshot looks strange.
HConsult your nearest JVC dealer for replacement.
● The light source or the subject does not include white. Or
there are various different light sources behind the subject.
HFind a white subject and compose your shot so that it also
appears in the frame. (੬ pg. 20)
● The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
There is no picture.
● The camcorder is not getting power, or some other
malfunction exists.
HTurn the camcorder’s power off and on again. (੬ pg. 8)
HDisengage the Sepia (SEPIA) and Monotone
(MONOTONE). (੬ pg. 14, 20)
Some functions are not available using the
MENU/VOL. Wheel.
The image taken using Snapshot is too dark.
● The Power Switch is set to “A”.
HSet the Power Switch to “M”. (੬ pg. 8)
● Shooting was performed under backlit conditions.
HPress BACKLIGHT. (੬ pg. 23)
When the image is printed from the printer, a black
bar appears at the bottom of the screen.
The image taken using Snapshot is too bright.
● The subject is too bright.
HSet “r” to “SPOTLIGHT”. (੬ pg. 20)
● This is not a malfunction.
HBy recording with “DIS” activated (੬ pg. 14, 15) this can
be avoided.
White Balance cannot be activated.
● The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
HDisengage the Sepia (SEPIA) or Monotone (MONOTONE)
mode before setting White Balance. (੬ pg. 20)
Wipe/Fader effects do not work.
● The Power Switch is set to “A”.
HSet the Power Switch to “M”. (੬ pg. 8)
The Black & White Fader does not work.
● The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
HDisengage the Sepia (SEPIA) and Monotone
(MONOTONE). (੬ pg. 14, 20)
Program AE with special effects does not work.
● The Power Switch is set to “A”.
HSet the Power Switch to “M”. (੬ pg. 8)
The image looks like the shutter speed is too slow.
● When shooting in the dark, the unit becomes highly
sensitive to light when “GAIN UP” is set to “AUTO”.
HIf you want the lighting to look more natural, set “GAIN UP”
to “AGC” or “OFF”. (੬ pg. 14, 15)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN TROUBLESHOOTING
30
When the camcorder is connected via the DV
connector, the camcorder does not operate.
Images on the LCD monitor are jittery.
● The speaker volume is too great.
HTurn the speaker volume down. (੬ pg. 12)
● The DV cable was plugged/unplugged with power turned
on.
The LCD monitor, the viewfinder and the lens have
become dirty (ex. fingerprints).
HTurn the camcorder’s power off and on again, then operate
it.
HWipe them gently with soft cloth. Wiping strongly can
cause damage. (੬ pg. 34) To clean the viewfinder, please
consult your nearest JVC dealer.
The rear of the LCD monitor is hot.
● The light used to illuminate the LCD monitor causes it to
become hot.
HClose the LCD monitor to turn it off or set the Power Switch
to “OFF”, and let the unit cool down.
Time code does not appear.
● “TIME CODE” is set to “OFF”.
HSet “TIME CODE” to “ON”. (੬ pg. 14, 16, 17)
Images on the LCD monitor appear dark or whitish.
An error indication (E01, E02 or E06) appears.
● In places subject to low temperature, images become dark
due to the characteristics of the LCD monitor. When this
happens, the displayed colours differ from those that are
actually recorded. This is not a defect of the camcorder.
HAdjust the brightness and angle of the LCD monitor.
(੬ pg. 9, 10)
● A malfunction of some kind has occurred. In this case the
camcorder’s functions become unusable.
H੬ pg. 31.
An error indication (E03 or E04) appears.
● When the LCD monitor’s fluorescent light reaches the end
of its service life, images on the LCD monitor become dark. ● A malfunction of some kind has occurred. In this case the
HConsult your nearest JVC dealer.
camcorder’s functions become unusable.
H੬ pg. 31.
Coloured bright spots appear all over the LCD
monitor or the viewfinder.
● The LCD monitor and the viewfinder are made with high-
precision technology. However, black spots or bright spots
of light (red, green or blue) may appear constantly on the
LCD monitor or the viewfinder during recording or
playback. These spots are not recorded on the tape. This is
not due to any defect of the unit. (Effective dots: more than
99.99 %)
The indicators and the image colour on the LCD
monitor are not clear.
● This may occur when the surface or the edge of the LCD
monitor is pressed.
The cassette will not load properly.
● The battery’s charge is low.
HInstall a fully charged battery. (੬ pg. 6, 7)
Picture does not appear on the LCD monitor.
● The viewfinder is pulled out and “PRIORITY” is set to
“FINDER”.
HPush the viewfinder back in or set “PRIORITY” to “LCD”.
(੬ pg. 10, 14, 16)
● The LCD monitor’s brightness setting is too dark.
HAdjust the brightness of the LCD monitor. (੬ pg. 9)
HIf the monitor is tilted upward 180 degrees, open the
monitor fully. (੬ pg. 10)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING EN
31
Warning Indications
E01, E02 or E06
UNIT IN SAFEGUARD MODE REMOVE AND
REATTACH BATTERY
of malfunction has occurred. When an error indication
appears, the camcorder turns off automatically. Remove
the power supply (battery, etc.) and wait a few minutes for
the indication to clear. When it does, you can resume
using the camcorder. If the indication remains, consult
your nearest JVC dealer.
Displays the battery remaining power.
Remaining power level
High
Exhausted
As the battery power comes close to nil, the battery
indicator blinks.
When the battery power is exhausted, power turns off
automatically.
E03 or E04
UNIT IN SAFEGUARD MODE EJECT AND REINSERT
TAPE
Appears when no tape is loaded. (੬ pg. 9)
The error indications (E03 or E04) show what type of
malfunction has occurred. When an error indication
appears, the camcorder turns off automatically. Eject the
cassette once and re-insert it, then check if the indication
clears. When it does, you can resume using the
camcorder. If the indication remains, consult your nearest
JVC dealer.
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to “SAVE”
while the Power Switch is set to “A” or “M”. (੬ pg. 8)
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during recording.
Use an optional cleaning cassette. (੬ pg. 33)
CONDENSATION, OPERATION PAUSED
PLEASE WAIT
Appears if condensation occurs. (The two indications
above swiches alternately every 3 seconds.) When this
indication is displayed, wait more than 1 hour until
condensation disappears.
TAPE!
Appears if a tape is not loaded when the Recording Start/
Stop Button or SNAPSHOT Button is pressed while the
Power Switch is set to “A” or “M”.
TAPE END
Appears when the tape ends during recording or
playback. (੬ pg. 27)
SET DATE/TIME!
● Appears when the date/time is not set. (੬ pg. 8)
● Appears when the built-in clock (lithium) battery is
discharged and the previously set date/time is erased.
(੬ pg. 8)
LENS CAP
Appears for 5 seconds after power is turned on if the lens
cap is attached.
COPYING FAILED
● Appears if dubbing of copyguarded signals is attempted
while this camcorder is being used as a recorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN CAUTIONS
32
Battery Packs
Cassettes
The supplied battery pack is
a lithium-ion battery. Before
using the supplied battery
pack or an optional battery
pack, be sure to read the
following cautions:
● To avoid hazards…
...do not burn.
...do not short-circuit the
terminals. When transporting, make sure the provided
battery cap is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
...do not modify or disassemble.
...do not expose the battery to temperatures exceeding
60°C, as this may cause the battery to overheat, explode
or catch fire.
...use only specified chargers.
● To prevent damage and prolong service life…
...do not subject to unnecessary shock.
...charge in an environment where temperatures are within
the tolerances shown in the chart below. This is a chemical
reaction type battery — cooler temperatures impede
chemical reaction, while warmer temperatures can prevent
complete charging.
...store in a cool, dry place. Extended exposure to high
temperatures will increase natural discharge and shorten
service life.
...fully charge and then fully discharge the battery every 6
months when storing the battery pack over a long period
time.
...remove from charger or powered unit when not in use, as
some machines use current even when switched off.
To properly use and store your cassettes, be sure to read
the following cautions:
● During use…
...make sure the cassette bears the Mini DV mark.
...be aware that recording onto prerecorded tapes
automatically erases the previously recorded video and
audio signals.
Terminals
...make sure the cassette is positioned properly when
inserting.
...do not load and unload the cassette repeatedly without
allowing the tape to run at all. This slackens the tape and
can result in damage.
...do not open the front tape cover. This exposes the tape to
fingerprints and dust.
● Store cassettes…
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary shock or
vibration.
...where they won’t be exposed to strong magnetic fields
(such as those generated by motors, transformers or
magnets).
...vertically, in their original cases.
LCD Monitor
● To prevent damage to the LCD monitor, DO NOT…
...push it strongly or apply any shocks.
...place the camcorder with the LCD monitor on the bottom.
● To prolong service life…
...avoid rubbing it with coarse cloth.
● Be aware of the following phenomena for LCD
monitor use. These are not malfunctions…
...While using the camcorder, the surface around the LCD
monitor and/or the back of the LCD monitor may heat up.
...If you leave power on for a long time, the surface around
the LCD monitor becomes hot.
NOTES:
● It is normal for the battery pack to be warm after charging,
or after use.
Temperature Range Specifications
Charging: 10°C to 35°C
Operation: 0°C to 40°C
Storage: –20°C to 50°C
● The lower the temperature, the longer recharging takes.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS EN
33
Main Unit
How To Handle A CD-ROM
● Take care not to soil or scratch the mirror surface (opposite
to the printed surface). Do not write anything or put a sticker
on either the front or back surface. If the CD-ROM gets
dirty, gently wipe it with a soft cloth outward from the centre
hole.
● Do not use conventional disc cleaners or cleaning spray.
● Do not bend the CD-ROM or touch its mirror surface.
● Do not store your CD-ROM in a dusty, hot or humid
environment. Keep it away from direct sunlight.
● For safety, DO NOT…
...open the camcorder’s chassis.
...disassemble or modify the unit.
...short-circuit the terminals of the battery pack. Keep it away
from metallic objects when not in use.
...allow inflammables, water or metallic objects to enter the
unit.
...remove the battery pack or disconnect the power supply
while the power is on.
...leave the battery pack attached when the camcorder is not
in use.
● Avoid using the unit…
About moisture condensation
● You have observed that pouring a cold liquid into a glass
will cause drops of water to form on the glass’ outer
surface. This same phenomenon occurs on the head
drum of a camcorder when it is moved from a cool place
to a warm place, after heating a cold room, under
extremely humid conditions or in a place directly
subjected to the cool air from an air conditioner.
● Moisture on the head drum can cause severe damage to
the video tape, and can lead to internal damage to the
camcorder itself.
...in places subject to excessive humidity or dust.
...in places subject to soot or steam such as near a cooking
stove.
...in places subject to excessive shock or vibration.
...near a television set.
...near appliances generating strong magnetic or electric
fields (speakers, broadcasting antennas, etc.).
...in places subject to extremely high (over 40°C) or
extremely low (under 0°C) temperatures.
● DO NOT leave the unit…
...in places of over 50°C.
...in places where humidity is extremely low (below 35%) or
extremely high (above 80%).
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
...in direct sunlight.
...in a closed car in summer.
...near a heater.
● To protect the unit, DO NOT…
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during
transportation.
...keep the lens directed at extremely bright objects for long
periods.
The camcorder is a microcomputer-controlled device.
External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such
cases, first disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few minutes and
then re-connect it and proceed as usual from the
beginning.
...expose the lens and viewfinder’s lens to direct sunlight.
...carry it by holding the LCD monitor or the viewfinder.
...swing it excessively when using the hand strap or the grip.
...swing the soft camera case excessively when the
camcorder is inside it.
● Dirty heads can cause the following problems:
...No picture during playback.
...Blocks of noise appear during playback.
...During recording, the Head Clog Warning indicator “
appears.
”
...Recording cannot be performed properly.
In such cases, use an optional cleaning cassette. Insert it and
play back. If the cassette is used more than once
consecutively, damage to the video heads may result. After
the camcorder plays back for about 20 seconds, it stops
automatically. Also refer to the cleaning cassette’s
instructions.
If, after using the cleaning cassette, the problems still exist,
consult your nearest JVC dealer.
Mechanical moving parts used to move the video heads and
video tape tend to become dirty and worn out over time. In
order to maintain a clear picture at all times, periodic check-
ups are recommended after using the unit for about 1,000
hours. For periodic check-ups please consult your nearest
JVC dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN USER MAINTENANCE
34
After Use
Cleaning The Camcorder
1 Turn off the camcorder.
1 To clean the exterior, wipe gently with a soft cloth. Put
the cloth in diluted mild soap and wring it well to wipe off
heavy dirt. Then wipe again with a dry cloth.
2 Slide and hold OPEN/EJECT in the direction of the
arrow, then pull the cassette holder cover open until it
locks. The cassette holder opens automatically. Remove 2 Press the Monitor Opening Button and open the LCD
the cassette.
monitor. Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
3 Press “PUSH HERE” to close the cassette holder.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
3 To clean the lens, blow it with a blower brush, then
wipe gently with lens cleaning paper.
NOTES:
4 Slide BATT.RELEASE 1 and remove the battery pack
2 3.
● Avoid using strong cleaning agents such as benzine or
alcohol.
● Cleaning should be done only after the battery pack has
been removed or other power units have been
disconnected.
● Mould may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth refer to
the cautions of each product.
OPEN/EJECT
Cassette holder
cover
● To clean the viewfinder, please consult your nearest JVC
dealer.
PUSH HERE
Remove.
Cassette holder
BATT.RELEASE
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS EN
35
Camcorder
For Digital Video Camera
Format
DV format (SD mode)
Signal format
PAL standard
Recording/Playback format
Video: Digital component recording
Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
Mini DV cassette
For General
Power supply
DC 11.0 V (Using AC Adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 3.3 W (LCD monitor off, viewfinder on)
Approx. 4.6 W (LCD monitor on, viewfinder off)
Approx. 8.6 W (Maximum)
Dimensions (W x H x D)
71 mm x 91 mm x 118 mm
(with the LCD monitor closed and the viewfinder pushed
back in)
Weight
Approx. 500 g
(without cassette and battery)
Approx. 590 g
Tape speed
SP: 18.8 mm/s, LP: 12.5 mm/s
Maximum recording time (using 80 min. cassette)
SP: 80 min., LP: 120 min
For Connectors
S
(incl. cassette and battery)
Operating temperature
0°C to 40°C
Operating humidity
35% to 80%
Storage temperature
–20°C to 50°C
Pickup
S-Video output:
Y: 1.0 V (p-p), 75 Ω, analogue
C: 0.29 V (p-p), 75 Ω, analogue
AV
Video output: 1.0 V (p-p), 75 Ω, analogue
Audio output: 300 mV (rms), 1 kΩ, analogue, stereo
DV
Output: 4-pin, IEEE 1394 compliant
1/6" CCD
Lens
AC Adapter
Power requirement
AC 110 V to 240 Vd, 50 Hz/60 Hz
Output
F 1.6, f = 2.7 mm to 43.2 mm, 16:1 power zoom lens
Filter diameter
ø30.5 mm
LCD monitor
DC 11 V G, 1 A
2.37" diagonally measured, LCD panel/TFT active matrix
system
Viewfinder
Electronic viewfinder with 0.24" colour LCD
Speaker
Monaural
Specifications shown are for SP mode unless otherwise
indicated. E & O.E. Design and specifications subject to
change without notice.
White LED Light
Effective distance: 1.5 m
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX EN
37
Controls
a Menu Wheel [MMENU/VOL.] (੬ pg. 14)
Speaker Volume Control [MMENU/VOL.] (੬ pg. 12)
c Power Zoom Lever [T/W] (੬ pg. 10)
d Manual Focus Button [FOCUS] (੬ pg. 21)
Blank Search Button [BLANK SRCH] (੬ pg. 12)
e Dioptre Adjustment Control (੬ pg. 8)
f Recording Start/Stop Button (੬ pg. 10)
g Power Switch [A, M, PLAY, OFF] (੬ pg. 8)
h Lock Button (੬ pg. 8)
* i.Link refers to the IEEE1394-1995 industry specification
compliant with the i.Link standard.
Indicators
U POWER/CHARGE Lamp (੬ pg. 8, 10)
i Stop Button [8] (੬ pg. 12)
j Rewind Button [3] (੬ pg. 12)
Night Button [NIGHT] (੬ pg. 18)
Other Parts
V Shoulder Strap Eyelet (੬ pg. 5)
W Battery Pack Mount (੬ pg. 6)
X Grip Strap (੬ pg. 7)
k Play/Pause Button [4/9] (੬ pg. 12)
l Fast-Forward Button [5] (੬ pg. 12)
Backlight Compensation Button [BACKLIGHT]
(੬ pg. 23)
m Battery Release Switch [BATT.RELEASE] (੬ pg. 6)
n Cassette Open/Eject Switch [OPEN/EJECT] (੬ pg. 9)
o White LED Light Switch [LIGHT] (੬ pg. 18)
p Monitor Opening Button (੬ pg. 10)
For models without button, simply pull on bottom end
of LCD monitor to open.
Y LCD Monitor (੬ pg. 10, 11)
Z Speaker (੬ pg. 12)
b Stud Hole (੬ pg. 9)
c Tripod Mounting Socket (੬ pg. 9)
d Cassette Holder Cover (੬ pg. 9)
e Stereo Microphone
f White LED Light (੬ pg. 18)
g Viewfinder (੬ pg. 8)
h Camera Sensor
(Be careful not to cover this area, a sensor necessary
for shooting is built-in here.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN INDEX
38
During Video Playback
LCD Monitor/Viewfinder Indications
1
2
3 4
During Video Recording
12 b i t / M I X
L
I
J
g
K LM
N
O
1h40m
A
B
40
x
W
T
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
P
REC
C
D
E
F
G
Q
g
3
VOLUME
5
BRIGHT
1 0
.
11. 04
10: 00
R
S
20 : 21 : 25
SOUND 12 b i t
g
10
.
11. 04
8
7
6
15:55
H
d U : Playback
W
V U
T
a Operation Mode (੬ pg. 8)
b
: Night-Scope Indicator (੬ pg. 18)
(Appears when Night-Scope is engaged.)
: Gain Up Mode (੬ pg. 15)
(Appears when “GAIN UP” is set to “AUTO” and the
shutter speed is automatically adjusted.)
c White LED Light Indicator (੬ pg. 18)
d White Balance Indicator (੬ pg. 23)
: Backlight Compensation Indicator (੬ pg. 23)
: Exposure Adjustment Indicator (੬ pg. 22)
(੬ pg. 19)
5
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
3
9 : Pause
Motion
Y 9 : Reverse Frame-By-Frame Playback/Slow-
e
(੬ pg. 12)
(The level indicator g moves.)
Viewfinder) (੬ pg. 9)
i Approximate Zoom Ratio (੬ pg. 10)
(Appears during zooming.)
j Zoom Indicator (੬ pg. 10)
(Appears during zooming.)
(The level indicator g moves.)
h Time Code (੬ pg. 16, 17)
(The level indicator g moves.)
l Tape Running Indicator (੬ pg. 10)
(Rotates while tape is running.)
m Selected Wide Mode Indicator (੬ pg. 15)
n Recording Speed Mode (SP/LP) (੬ pg. 15)
o Tape Remaining Time (੬ pg. 10)
PAUSE: (Appears during Record-Standby mode.)
(੬ pg. 10)
O: (Appears when taking Snapshot.) (੬ pg. 20)
q BRIGHT: Brightness Control Indicator (LCD monitor/
Viewfinder) (੬ pg. 9)
(The level indicator g moves.)
r Wind Cut Indicator (੬ pg. 15)
s Battery Indicator (੬ pg. 31)
t Date/Time (੬ pg. 8, 16)
u Sound Mode Indicator (੬ pg. 15)
(Appears for approx. 5 seconds after turning on the
camcorder.)
v Manual Focus Adjustment Indicator (੬ pg. 21)
w Time Code (੬ pg. 16, 17)
Download from Www.Somanuals.com. All Manuals Search And Download.
A
AC Adapter ................................................................6, 7 Night-Scope ................................................................ 18
Auto Focus ...................................................................21
Auto Shut Off .........................................................10, 27
Playback sound (SOUND MODE, NARRATION) ....... 17
B
Power Switch Position ................................................... 8
Backlight Compensation ..............................................23
Beep (BEEP) ...............................................................16
Blank search ................................................................12
Brightness Adjustment Of The Display (BRIGHT) .........9
Program AE With Special Effects (PROGRAM AE)
Classic Film (CLASSIC FILM) .............................. 20
Sports (SPORTS) ................................................. 19
Spotlight (SPOTLIGHT) ........................................ 20
Twilight (TWILIGHT) ............................................. 20
Provided Accessories .................................................... 5
C
Changing The Menu Settings ......................................14
Charging The Battery Pack ............................................6
Cleaning The Camcorder .............................................34
Clock adjustment (CLOCK ADJ.) ...................................8
Connections
Charging .................................................................6
Dubbing ..........................................................24, 25
To A PC ................................................................26
Recording Mode (REC MODE) ............................. 15, 17
Recording Time
Tape ....................................................................... 9
Resetting Menu Settings (CAM RESET) ..................... 16
Rewind The Tape ........................................................ 12
D
Date/Time
Display (DATE/TIME) ......................................16, 17
Settings ...................................................................8
Digital Image Stabilisation (DIS) ..................................15
Dubbing .................................................................24, 25
S
Shuttle Search ............................................................. 12
Snapshot Mode (SNAP MODE) .................................. 15
Sound Mode (SOUND MODE) .............................. 15, 17
Specifications .............................................................. 35
Still Playback ............................................................... 12
E
Erase Protection ............................................................9
Exposure Control (EXPOSURE) ..................................22
F
Fade-In/Out ..................................................................19
T
G
Telephoto setting (TELE MACRO) .............................. 15
Grip Adjustment .............................................................7
I
Indications on the LCD Monitor/Viewfinder ..................38
Iris ................................................................................22
J
Journalistic Shooting ....................................................11
W
White Balance (W.BALANCE) .................................... 23
White LED Light .......................................................... 18
Wide Mode (WIDE MODE)
L
Loading A Cassette .......................................................9
M
Cinema (CINEMA) ................................................ 15
Squeeze (SQUEEZE) ........................................... 15
Wipe In/Out ................................................................. 19
Manual Focus ..............................................................21
Menu Screen
CAMERA ...............................................................15
CAMERA DISPLAY ..............................................16
MANUAL ...............................................................15
SYSTEM .........................................................16, 17
VIDEO ...................................................................17
VIDEO DISPLAY ...................................................17
Motor Drive Mode ........................................................20
Z
Zooming (ZOOM) .................................................. 10, 15
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in Malaysia
1203-FO-ID-PJ
COPYRIGHT© 2003 VICTOR COMPANY OF JAPAN, LTD.
EK
Download from Www.Somanuals.com. All Manuals Search And Download.
|
