Instruction manual
Model SC300
Model SC400
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SC300
DESCRIPTION OF THE APPLIANCE
A
B
C
D
E
F
G
H
I
Floorcloth
Main part of the appliance
On/Off switch
Safety Filling Cap
On/Off pilot light
Power cable
Telescopic tube
165ml measuring cup
Funnel
L
Preheating/cool down stand
L
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR USE MODEL SC300
Using KENWOOD STEAM MOP is really very simple:
1. After having taken the appliance out of its box, screw the telescopic tube onto the main part of the appliance (Fig.1). Then
turn the two ends and pull them out to the desired length. Lock the upper part by turning clockwise (Figs 1a-1b).
2. Secure the cable onto the hook at the top of the tube (Fig.2).
3. Rest the base of KENWOOD STEAM MOP on the floorcloth, secure the floor cloth to the KENWOOD STEAM MOP using
the Velcro straps, making sure the cloth is secured on the base (Fig.3).
4. Unscrew the Safety cap (D) and pour 2 measuring cups (H) (330 ml) into the tank using the provided funnel, then screw
the Safety cap back on (Fig 4).
5. Place the Steam mop on the provided preheat tray. Plug the power cord into the power supply. Press switch (C) and wait
for about 3 minutes (Fig.5). Do not leave the device unattended during the waiting period.
6. As soon as steam appears from your KENWOOD STEAM MOP you can start to use it. Slowly run the KENWOOD STEAM
MOP over the surfaces to be cleaned. DO NOT LEAVE in one spot for more than 15 seconds as it may cause a whitish
halo to form on the surface. This is no call for concern as it may be removed using a normal decalcifying product or with
a few drops of vinegar directly onto the floor.
7. When KENWOOD STEAM MOP SC300 no longer emits steam it means that there is no more water (this will take place
approximately every 15 minutes when in use).Turn off the appliance, take out the plug, and supply more water as
described in Point 4 above.
8. Turn your KENWOOD STEAM MOP on again and steam will start to be produced as before.
9. When finished wash the cloth with water and soap or in washing machine. Every time you replace the cloth, turn off the
switch (C) and do not touch the appliances hot parts.
10. After using and before putting the appliance away, wind the power cord around the provided hooks (see Fig. 6) and empty
any water left in the tank of the Steam Mop. Before using the appliance again, unwind the power cord completely. Be sure
the power cord is completely unwound before you plug it in.
CLEANING AND MAINTENANCE
The following operation must be carried out only if the appliance is unplugged from its power source.
In order to guarantee perfect functioning over a long period of time the tank needs to be rinsed out at least once a week with
cold water to eliminate any accumulated calcium deposits.
DO NOT USE VINEGAR OR OTHER DECALCIFYING SUBSTANCES.
KENWOOD STEAM MOP does not need to be used with its own specially developed floor cloths but can be used with the
floor cloths that you normally use in your home.
Spare floor cloths are available by mail order from Hagemeyer.
Attention.
Before washing the Magic Cloth, Kenwood recommends the Magic Cloth straps be neatly joined together
to avoid lint clogging the magic tape hooks.
PROBLEM
CAUSE
SOLUTION
Appliance
won’t start
* Electric plug
*Push plug securely into outlet
*Try another outlet
*Check circuit breaker
* Power switch not turned on
* No water in tank
*Make sure power switch is on
*Check the tank for water
Appliance won’t make steam
*No water in tank
*Check the tank for water
Appliance leaves water on the floor
*Floorcloth is too wet
*Change floorcloth
*If wood floor, dry the floor before proceeding.
*Too much water in tank, Do not overfill
*Turn off, unplug from electrical outlet, change
floorcloth and reheat appliance.
*Appliance did not remain flat on surface
while turned on
Appliance leaves a whitish halo on
floor
*Left in one spot too long
*Remove with few drops of vinegar.
*If above step doesn’t remove halo, then reheat
area for one minute and discoloration will be
removed. Do not overheat area.
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SC400
DESCRIPTION OF THE APPLIANCE
A
B
C
D
E
F
G
H
I
Floorcloth
Main part of the appliance
On/Off switch
Safety Filling Cap
On/Off pilot light
Water exhaustion light
Power cable
Telescopic tube
165ml measuring cup
Funnel
H
I
L
F
E
D
C
L
M
B
G
Preheating/cool down stand
A
M
Fig. 3
Fig. 1
Fig. 2
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR USE MODEL SC400
Using KENWOOD STEAM MOP is really very simple:
1. Once the appliance has been unpacked, fit the extension tube in the appliance’s body and then extend it to the desired
length (fig. 1).
2. Fix the top part of the tube by turning it in a clockwise direction (fig. 2).
3. Fix the cord into the hook which is provided along the tube (fig. 3)
4. Rest the base of KENWOOD STEAM MOP on the floorcloth, secure the floor cloth to the KENWOOD STEAM MOP using
the Velcro straps, making sure the cloth is secured on the base (fig. 4).
5. Unscrew the cap (D) and pour 2 measuring jugs (I) of water into the tank using the provided funnel (L) (fig. 5). Then screw
the safety cap on tightly. Now insert the plug into the power outlet.
6. Place the Steam Mop on the provided preheat tray. Press the switch (C), the pilot light (E) will go on (fig. 6). Do not leave
the appliance unattended while you are waiting for the Steam Mop to heat up.
7. When steam starts coming out, slowly run the appliance over the surfaces to be cleaned. This way your floors will
become perfectly clean.DO NOT LEAVE in one spot for more than 15 seconds as it may cause a whitish halo to form on
the surface. This is no call for concern as it may be removed using a normal decalcifying product or with a few drops of
vinegar directly onto the floor.
8. When Steam Mop stops producing steam and the water exhaustion light (F) goes on it means that the water has run
out (approximately every 15 minutes use). In this case, press the switch (C), unplug the appliance and refill with water as
described at point 5. During this operation, mind not to touch the appliances hot parts.
9. Press the switch (C) again. Steam Mop will restart producing steam.
10. When finished wash the cloth with water and soap or in washing machine.Every time you replace the cloth, turn off the
switch (C) and do not touch the appliances hot parts.
11. After using and before putting the appliance away, wind the power cord around the provided hooks (see fig. 7) and empty
any water left in the tank of the Steam Mop. Before using the appliance again, unwind the power cord completely. Be sure
the power cord is completely unwound before you plug it in.
CLEANING AND MAINTENANCE
The following operation must be carried out only if the appliance is unplugged from its power source.
In order to guarantee perfect functioning over a long period of time the tank needs to be rinsed out at least once a week with
cold water to eliminate any accumulated calcium deposits.
DO NOT USE VINEGAR OR OTHER DECALCIFYING SUBSTANCES.
KENWOOD STEAM MOP does not need to be used with its own specially developed floor cloths but can be used with the
floor cloths that you normally use in your home.
Spare floor cloths are available by mail order from Hagemeyer.
Attention.
Before washing the Magic Cloth, Kenwood recommends the Magic Cloth straps be neatly joined together
to avoid lint clogging the magic tape hooks.
PROBLEM
CAUSE
SOLUTION
Appliance
won’t start
* Electric plug
*Push plug securely into outlet
*Try another outlet
*Check circuit breaker
* Power switch not turned on
* No water in tank
*Make sure power switch is on
*Check the tank for water
Appliance won’t make steam
*No water in tank
*Check the tank for water
Appliance leaves water on the floor
*Floorcloth is too wet
*Change floorcloth
*If wood floor, dry the floor before proceeding.
*Too much water in tank, Do not overfill
*Turn off, unplug from electrical outlet, change
floorcloth and reheat appliance.
*Appliance did not remain flat on surface
while turned on
Appliance leaves a whitish halo on
floor
*Left in one spot too long
*Remove with few drops of vinegar.
*If above step doesn’t remove halo, then reheat
area for one minute and discoloration will be
removed. Do not overheat area.
Download from Www.Somanuals.com. All Manuals Search And Download.
HAGEMEYER AUSTRALASIA B.V.
104 Vanessa street
Kingsgrove
NSW 2208
Ph: (02) 93.70.88.77
LIMITED
New Lane. Havant. Hants. P09 2NH
Download from Www.Somanuals.com. All Manuals Search And Download.
|