CD-RECEIVER
KDC-X959
INSTRUCTION MANUAL
COMPACT
DIGITAL AUDIO
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the
best performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on
the warranty card, and in the space provided below. Refer to the model and serial
numbers whenever you call upon your KENWOOD dealer for information or service on
the product.
Model KDC-X959
Serial number
© B64-2257-00 (KV)
Download from Www.Somanuals.com. All Manuals Search And Download.
2Warning
NOTE
2CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
Use of controls or adjustments or performance
of procedures other than those specified
herein may result in hazardous radiation
exposure.
In compliance with Federal Regulations,
following are reproductions of labels on, or
inside the product relating to laser product
safety.
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference to
radio communications, if it is not installed and
used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
Location : Bottom Panel
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
NOTE
This Class B digital apparatus complies with
Canadian ICES-003.
— 3 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
IMPORTANT INFORMATION
About the disc changer/CD player to
be connected:
To connect a disc changer having the "O-N"
switch to this unit, set the "O-N" switch to "N".
Precautions when connecting disc
changers/CD players released in 1997 or
earlier.
When you connect a model with no "O-N"
switch, the converter cord CA-DS100
available as an option may be required. For
details, consult your Kenwood dealer.
A disc changer doesn't work when it is
connected without using these options.
If a model with no "O-N" switch is
connected, some unavailable functions and
information that cannot be displayed are
generated.
2WARNING
2CAUTION
To prevent injury or fire, take the
following precautions:
• Insert the unit all the way in until it is fully
locked in place. Otherwise it may fall out of
place when jolted.
• When extending the ignition, battery, or
ground wires, make sure to use automotive-
grade wires or other wires with a 0.75mm
(AWG18) or more to prevent wire
deterioration and damage to the wire
coating.
• To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not open the top or bottom covers of the
unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
• To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
2
Note that none of the KDC-C100, KDC-C302,
C205, C705, and non-Kenwood CD changers
can be connected.
You can damage both your unit and the CD
changer if you connect them incorrectly.
• Be careful not to drop the unit or subject it to
strong shock.
The unit may break or crack because it
contains glass parts.
Do Not Load 8-cm (3-in.) CDs in the CD
slot
If you try to load an 8-cm CD with its adapter
into the unit, the adapter might separate from
the CD and damage the unit.
• Do not apply excessive force to the moving
faceplate. Doing so will cause damage or
malfunction.
• Do not apply excessive force to the open
faceplate or place objects on it. Doing so will
cause damage or breakdown.
— 4 —
Download from Www.Somanuals.com. All Manuals Search And Download.
About RDS
Lens Fogging
RDS (Radio Data System)
NOTE
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a while,
consult your Kenwood dealer.
RDS is a service used by radio stations to
transmit data outside normal radio broadcast
signals.
• If you experience problems during
installation, consult your Kenwood dealer.
When an RDS station is received, you can
immediately find out what kind of data is being
transmitted by looking at the program service
name, which appears in the display after the
frequency.
The RDS indicator turns on when an RDS
station is being received.
• If the unit fails to operate properly, press the
Reset button. The unit returns to factory
settings when the Reset button is pressed.
If the unit still fails to operate properly after
the Reset button has been pressed, contact
your local KENWOOD dealer for assistance.
• Press the reset button if the disc auto
changer fails to operate correctly. Normal
operation should be restored.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Alarm
When an emergency transmission (announcing
disasters, etc.) is made, the current function
will be interrupted to allow the warning to be
received under the following conditions:
during tuner reception, or when the Traffic
Information function is turned on.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it
with a dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain
off with a cloth moistened with neutral
cleaner, then wipe neutral detergent off.
Applying spray cleaner directly to the unit may
affect its mechanical parts. Wiping the
faceplate with a hard cloth or using a volatile
liquid such as thinner or alcohol may scratch
the surface or erases characters.
Reset button
• We recommend the use of the Security
Code function (see p. 34) to prevent theft.
• The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
Cleaning the CD Slot
As dust tends to accumulate in the CD slot,
clean it every once in a while. Your CDs can
get scratched if you put them in a dusty CD
slot.
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
— 5 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on playing MP3/WMA
This unit can play MP3(MPEG1, 2, 2.5 Audio Layer 3)/WMA. Note,
however, that the MP3/WMA recording media and formats
acceptable are limited. When writing MP3/WMA, pay attention to
the following restrictions.
Entering ID3 tag and Contents
Description
The Displayable ID3 tag is ID3 version
1.x.
For the character code, refer to the List
of Codes.
Acceptable media
The MP3/WMA recording media acceptable to this unit are CD-ROM,
CD-R, and CD-RW.
Please use the full format when using CD-RW. If you use the quick
format, media may not be played.
Acceptable medium formats
The following formats are available for the media used in this unit. The
maximum number of characters used for file name including the
delimiter (".") and three-character extension are indicated in
parentheses.
• ISO 9660 Level 1 (12 characters)
• ISO 9660 Level 2 (31 characters)
• Joliet (64 characters)
• Romeo (128 characters)
Entering file and folder names
The code list characters are the only file
names and folder names that can be
entered and displayed.
If you use any other character for entry,
the file and folder names are not displayed correctly. They may neither
be displayed correctly depending on the CD writer used.
The unit recognizes and plays only those MP3/WMA which have the
MP3/WMA extension (.MP3/.WMA).
A file with a name entered with characters not on the code list may not
play correctly.
Up to 200 characters can be displayed in the long file name format.
For a list of available characters, see the instruction manual of the
writing software and the section Entering file and folder names below.
The media reproducible on this unit has the following limitations:
• Maximum number of directory levels: 8
• Maximum number of files per folder: 255
• Maximum number of characters for folder name: 64
• Maximum number of folders: 100
Writing files into a medium
When a medium containing MP3/WMA data is loaded, the unit checks
all the data on the medium. If the medium contains a lot of folders or
non-MP3/WMA files, therefore, it takes a long time until the unit starts
playing MP3/WMA.
In addition, it may take time for the unit to move to the next
MP3/WMA file or a Track Search or Album Search may not be
performed smoothly.
MP3/WMA written in the formats other than the above may not be
successfully played and their file names or folder names are not
properly displayed.
Loading such a medium may produce loud noise to damage the speakers.
• Do no attempt to play a medium containing a non-MP3/WMA file
with the MP3/WMA extension.
The unit mistakes non-MP3/WMA files for MP3/WMA data as long as
they have the MP3/WMA extension.
Settings for your MP3/WMA encoder and CD writer
Do the following setting when compressing audio data in WMA data
with the WMA encoder.
• Do not attempt to play a medium containing non MP3/WMA.
• Transfer bit rate: 48k —192 kbps
• Sampling frequency: 32k, 44.1k 48k Hz
When you use your CD writer to record MP3/WMA up to the
maximum disc capacity, disable additional writing. For recording on an
empty disc up to the maximum capacity at once, check Disc at Once.
— 6 —
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3/WMA playing order
When a Track Search is executed with file ¡$ being played ...
When selected for play, Album Search, Track Search, or for Album
Select, files and folders are accessed in the order in which they were
written by the CD writer.
Operation of the button
¢ Button
Current
file number
4 Button
Beginning of file
Because of this, the order in which they are expected to be played
may not match the order in which they are actually played. You may be
able to set the order in which MP3/WMA are to be played by writing
them onto a medium such as a CD-R with their file names beginning
with play sequence numbers such as "01" to "99", depending on your
CD writer.
When an Album Search is executed with file ¡$ being played ...
Operation of the button
Current
folder number
AM Button
FM Button
For example, a medium with the following folder/ file hierarchy is
subject to Album Search, Track Search, or Album Select as shown
below.
Example of a medium's folder/file hierarchy
When Album Select is selected with file ¡$ being played to move
from folder to folder ...
Operation of the button
Current
folder number
4 Button
¢ Button
AM Button
FM Button
Folder
File
Root
Level 1
Level 3
Level 2
Level 4
— 7 —
Download from Www.Somanuals.com. All Manuals Search And Download.
About CDs
Handling CDs
• Don’t touch the recording surface of the CD.
CD cleaning
Clean from the center of the disc and move
outward.
Removing CDs
When removing CDs from this unit pull them
• CD-R and CD-RW are easier to damage than
a normal music CD. Use a CD-R or a CD-RW
after reading the caution items on the
package etc.
• Don’t stick tape etc. on the CD.
Also, don’t use a CD with tape stuck on it.
out horizontally.
CDs that can’t be used
• CDs that aren’t round can’t be used.
When using a new CD
If the CD center hole or outside rim has burrs,
use it after removing them with a ball pen etc.
• CDs with coloring on the recording surface
or that are dirty can’t be used.
• Don’t use CDs without disc mark
.
Burrs
• A CD-R or CD-RW that hasn’t been finalized
can’t be played. (For the finalization process
refer to your CD-R/CD-RW writing software,
and your CD-R/CD-RW recorder instruction
manual.)
Burrs
CD storage
• Don’t place them in direct sunlight (On the
seat or dashboard etc.) and where the
temperature is high.
CD accessories
Don’t use disc type accessories.
• Store CDs in their cases.
— 8 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Power
Release button
FM
Turning ON the Power
S.A
u
¢
Press the [SRC] button.
When the power is ON, the <Security Code> (page 34) is displayed
as "CODE ON" or "CODE OFF".
Turning OFF the Power
Press the [SRC] button for at least 1 second.
4
d
ATT/
/
AM/
NF
LOUD
MENU
Q/
AUD
Selecting the Source
Press the [SRC] button.
SRC
DISP/
NAME.S
Source required
Display
Tuner
"TUNER"
CD
"Compact Disc"
"DiscChanger"
"AUX"
External disc
Auxiliary input
Standby (Illumination only mode)
"ALL OFF"
"AUX" is displayed in both the built-in Auxiliary input of this unit and
optional Auxiliary inputs.
Enter an Auxiliary input name in <Auxiliary Input Display Setting>
(page 20) to show the individual display.
The display above is an example when Display type is set to "Display Type A".
The function indicator is displayed only if it is "Display Type A".
— 9 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Volume
System Q
You can recall the best sound setting preset for different types of
the music.
Increasing Volume
Press the [u] button.
Decreasing Volume
1 Select the source to set
Press the [SRC] button.
Press the [d] button.
2 Select the Sound type
Press the [Q] button.
Each time the button is pressed the sound setting switches.
Sound setting
Display
Flat
User memory
Rock
Pops
Easy
"FLAT"
Attenuator
Turning the volume down quickly.
"User Preset"
"ROCK"
"POPS"
"EASY"
"TOP 40"
"JAZZ"
Press the [ATT] button.
Each time the button is pressed the Attenuator turns ON or OFF.
When it's ON, "ATT ON" is displayed.
Top 40
Jazz
• User memory: The values set on the <Audio control> (page 10).
• Each setting value is changed with the <Speaker & Woofer
Setting> (page 12).
First, select the speaker type with the Speaker setting.
Loudness
Compensating for low and high tones during low volume.
Press the [LOUD] button for at least 1 second.
Each time the button is pressed for at least 1 second the
Loudness turns ON or OFF.
Audio Control
When it's ON, "LOUD ON" is displayed.
1 Select the source for adjustment
Press the [SRC] button.
2 Enter Audio Control mode
Press the [AUD] button for at least 1 second.
— 10 —
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select the Audio item for adjustment
Press the [FM] or [AM] button.
Each time the button is pressed the items that can be adjusted
switch as shown below.
• According to the Bass Q Factor setting value, the frequencies that
can be set in Bass Center Frequency change as shown below.
Bass Q Factor
1.00/1.25/1.50
2.00
Bass Center Frequency
60/70/80/100
60/70/80/150
4 Adjust the Audio item
• When the bass extend is set to ON, low frequency response is
extended by 20%.
• Volume offset: Each source's volume can be set as a difference
from the basic volume.
• *: This mode is available only when <Non-fading Output> (page
19) is ON.
Press the [4] or [¢] button.
Adjustment Item
Display
Range
Bass Center
Frequency
"Bass FRQ"
60/70/80/100 or 150 (Hz)
Bass level
"Bass"
–8 — +8
1.00/1.25/1.50/2.00
ON/OFF
5 Exit Audio Control mode
Press the [AUD] button.
Bass Q Factor
Bass Extend
"Bass Q"
"Bass EXT"
Middle Center
Frequency
"Middle FRQ" 0.5/1.0/1.5/2.0
(kHz)
Middle level
Middle Q Factor
Treble Center
Frequency
"Middle"
"Middle Q"
"Treble FRQ"
–8 — +8
1.0/2.0
10.0/12.5/15.0/17.5 (kHz)
Treble level
Balance
Fader
"Treble"
"Balance"
"Fader"
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
–15 — +15
Non-Fading level*
"NF Level"
Front High Pass Filter "HPF Front"
Through/40/60/80/100/120/
150/180/220
(Hz)
Rear High Pass Filter "HPF Rear"
Through/40/60/80/100/120/
150/180/220
(Hz)
(Hz)
Non-Fading
"LPF NF"
50/80/120/Through
Low Pass Filter*
Non-Fading Phase*
Volume offset
"NF Phase"
"Volume Offset"–8 —
Normal (0°)/Reverse (180°)
0
— 11 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
In Woofer setting mode
Speaker & Woofer Setting
Speaker setting allows the System Q settings to be fine-tuned
according to the type of speakers.
Woofer type
Display
OFF
"Woofer OFF"
"12in type A"
"10in type A"
"12in type B"
"10in type B"
"12in type C"
"10in type C"
"8inch"
12 in. A type
10 in. A type
12 in. B type
10 in. B type
12 in. C type
10 in. C type
8 in. type
Woofer setting allows for Network configuration according to the
type of subwoofers.
1 Enter Standby
Press the [SRC] button.
Select the "ALL OFF" display.
2 Enter Speaker & Woofer Setting mode
Press the [Q] button.
"Speaker Setting" is displayed.
12 in. D type
10 in. D type
"12in type D"
"10in type D"
5 Exit Speaker & Woofer Setting mode
Press the [Q] button.
3 Select the Setting mode
Press the [FM] or [AM] button.
Each time the button is pressed it switches between Speaker
setting mode and Woofer setting mode.
4 Select the Speaker and Woofer type
Press the [4] or [¢] button.
Each time the button is pressed the setting switches as shown
below.
Switching Display Type
Setting the Display type.
Press the [DISP] button.
In Speaker setting mode
Each time the button is pressed the Display type switches as
shown below.
Speaker type
Display
OFF
"OFF"
"5/4 inch"
Display
Display mode
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
"6 9/6inch"
*
Picture
"O.E.M."
"Display Type D"
"Display Type A"
Character
information display
— 12 —
Download from Www.Somanuals.com. All Manuals Search And Download.
"Display Type B"
Character
information display
Character information display part a
Source type icon
Character information display part b
"Display Type B"
"Display Type C"
Picture
Character
information display
1 Select the Display Type
Press the [DISP] button.
2 Enter Display Control mode
Press the [S.A] button.
The display of each part can be changed.
- Picture:
"Display Control" is displayed.
<Display switching part for "Display Type C" and "Display Type
D"> (page 16)
3 Switch character information display part b
Press the [FM] or [AM] button.
- Character information display:
<Display switching part for "Display Type A" and "Display Type
B">: (page 13)
<Display switching part for "Display Type C" and "Display Type
D">(page 16)
Switch character information display part c
(Only when Display Type is "Display Type A")
Press the [4] or [¢] button.
Each time the button is pressed the display switches.
The Reference for the display content is after this operation's
explanation.
4 Exit Display Control mode
Press the [S.A] button.
Display switching part for "Display Type A" and
"Display Type B"
When Display Type is set to "Display Type A" or "Display Type
B", the displayed contents are changed.
Character information display part c cannot display the same
information as character information display part b.
"Display Type A"
Character information display part a
Character information display part b
Character information display part c
— 13 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
In Tuner source
In CD/ External disc source
Character information display part b Display
Character information display part b Display
Information
Display
Information
Display
Station name
or
Program Service name or Frequency
Radio text
Date & Clock
(Only when Display Type is "Display Type B")
Date
"SNPS+FREQ"
Disc name
Disc title
Track title
"DNPS"
"DISC-TITLE"
"TRACK-TITLE"
"DATE+CLOCK"
"R-TEXT"
"DATE+CLOCK"
Date & Clock
(Only when Display Type is "Display Type B")
Date
"DATE"
"DATE"
Blank (Only when Display Type is "Display Type A")
Blank (Only when Display Type is "Display Type A")
Frequency
Character information display part c Display
Information
"Frequency"
Display
Character information display part c Display
Information
Spectrum Analyzer & Clock
Track Title
Disc Title
Disc name
Blank
Date
"S/ANA+CLOCK"
"TRACK-TITLE"
"DISC-TITLE"
"DNPS"
Display
Spectrum Analyzer & Clock
Radio text
Blank
Date
Date & Clock
"S/ANA+CLOCK"
"R-TEXT"
"DATE"
"DATE"
"DATE+CLOCK" or "CLOCK"
Date & Clock
"DATE+CLOCK" or "CLOCK"
• The band display is always displayed on the a part display.
• For Station name registration refer to <Station/Disc Naming
(SNPS/DNPS)> (page 20).
• The Track Time is always displayed on the a part display.
• For Disc name registration refer to <Station/Disc Naming
(SNPS/DNPS )> (page 20).
— 14 —
Download from Www.Somanuals.com. All Manuals Search And Download.
In MP3/WMA source
In Auxiliary input source
Character information display part b Display
Character information display part b Display
Information
Display
Information
Display
Disc name
"DNPS"
Blank (Only when Display Type is "Display Type A")
Folder name
File name
Song title & Artist name
Album name & Artist name
Date & Clock
"FOLDER NAME"
"FILE NAME"
"TITLE/ARTIST"
"ALBUM/ARTIST"
"DATE+CLOCK"
Date
Date & Clock
(Only when Display Type is "Display Type B")
"DATE"
"DATE+CLOCK"
Character information display part c Display
Information
(Only when Display Type is "Display Type B")
Display
Date
"DATE"
Spectrum Analyzer & Clock
Blank
"S/ANA+CLOCK"
Blank (Only when Display Type is "Display Type A")
Date
Date & Clock
"DATE"
Character information display part c Display
"DATE+CLOCK" or "CLOCK"
Information
Display
Spectrum Analyzer & Clock
Album name & Artist name
Song title & Artist name
File name
Folder name
Disc name
Blank
Date
Date & Clock
"S/ANA+CLOCK"
"ALBUM/ARTIST"
"TITLE/ARTIST"
"FILE NAME"
"FOLDER NAME"
"DNPS"
The Auxiliary input name is always displayed on the a part display.
In Standby mode
Character information display part b Display
Information
Display
Blank (Only when Display Type is "Display Type A")
"DATE"
Date
"DATE"
"DATE+CLOCK" or "CLOCK"
Date & Clock
(Only when Display Type is "Display Type B")
"DATE+CLOCK"
• The Track Time is always displayed on the a part display.
• For Disc name registration refer to <Station/Disc Naming
(SNPS/DNPS)> (page 20).
Character information display part c Display
• The Album name cannot be displayed during WMA play.
Information
Display
Blank
Date
"DATE"
Date & Clock
"DATE+CLOCK" or "CLOCK"
The "ALL OFF" is always displayed on the a part display.
— 15 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Downloaded movie
Spectrum Analyzer 1
Spectrum Analyzer 2
Spectrum Analyzer 3
Spectrum Analyzer 4
Spectrum Analyzer 5
Wallpaper
Display switching part for "Display Type C" and
"Display Type D"
When Display Type is set to "Display Type C" or "Display Type
D", the displayed contents are changed.
"Display Type C"
Picture part a
4 Exit Display Control mode
Press the [S.A] button.
Character information display part b
• Wallpapers can be changed.
This unit comes with 5 types of wallpaper registered.
"Display Type D"
A downloaded wallpaper is added to the place after the last
original wallpaper of this unit.
Refer to <Wallpaper selecting> (page 18).
• A downloaded movie can be selected when it has been
downloaded into this unit.
Picture part a
1 Select the Display Type
Press the [DISP] button.
Refer to <Picture downloading> (page 18).
2 Enter Display Control mode
Press the [S.A] button.
"Display Control" is displayed.
3 Switch character information display part b
Press the [AM] button.
Each time the button is pressed the display switches.
The Reference for the display content is after this operation's
explanation.
In Tuner source
Character information display part b Display
Information
Display
Station name
"BAND+ch+SNPS"
Switch the Picture part a
Press the [FM] button.
Each time the button is pressed the display switches.
Display
or
Program Service name or Frequency
Frequency
Date
"BAND+ch+FREQ"
"DATE"
Demonstration
Movie 1
Date & Clock
Radio text
"DATE+CLOCK"
"R-TEXT"
Movie 2
— 16 —
Download from Www.Somanuals.com. All Manuals Search And Download.
For Station name registration refer to <Station/Disc Naming
(SNPS/DNPS)> (page 20).
• For Disc name registration refer to <Station/Disc Naming
(SNPS/DNPS)> (page 20).
• The Album name cannot be displayed during WMA play.
In CD/ External disc source
Character information display part b Display
In Auxiliary input source
Character information display part b Display
Information
Display
Disc name
Track Time
Date
"DNPS"
"P-Time"
"DATE"
Information
Display
Date
"DATE"
Date & Clock
Auxiliary input name
"DATE+CLOCK"
"AUX NAME"
Date & Clock
Track title
Disc title
"DATE+CLOCK"
"TRACK-TITLE"
"DISC-TITLE"
For Disc name registration refer to <Station/Disc Naming
(SNPS/DNPS )> (page 20).
In Standby mode
Character information display part b Display
In MP3/WMA source
Character information display part b Display
Information
Display
Date
Date & Clock
Standby display
"DATE"
"DATE+CLOCK"
"ALL OFF"
Information
Display
Disc name
"DNPS"
Track Time
"P-Time"
Date
"DATE"
Date & Clock
Album name & Artist name
Song title & Artist name
File name
"DATE+CLOCK"
"ALBUM/ARTIST"
"TITLE/ARTIST"
"FILE NAME"
"FOLDER NAME"
Folder name
— 17 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
1 Inset a CD-R/CD-RW.
Wallpaper selecting
Insert a CD-R/CD-RW containing files to be downloaded into this
unit. Refer to <Playing CD & MP3/WMA> (page 28) for details.
Our URL
Select a wallpaper to display when Display Type is set to
"Display Type C" or "Display Type D".
describes how to make CD-R/CD-RW.
1 Select the wallpaper display
Refer to <Display switching part for "Display Type C" and "Display
Type D"> (page 16).
2 Enter Standby
Press the [SRC] button.
Select the "ALL OFF" display.
2 Select the wallpaper
Display the wallpapers one after another and select one
1 Turn the wallpaper scan ON
3 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
Press the [38] button.
Each time the button is pressed the Wallpaper scan is turned
ON and OFF.
When it's ON, "SCAN" is displayed.
When it’s ON, each wallpaper is displayed every several
seconds.
4 Select the downloading mode
Press the [FM] or [AM] button.
Select the "Disp Data DL" display.
5 Enter the downloading mode
Press the [4] or [¢] button.
"File Check!!" is displayed.
2 At the wallpaper you want to display
Press the [38] button.
Select wallpaper manually
6 Select files to be downloaded
1 Turn the wallpaper scan OFF.
Press the [38] button.
Press the [FM] or [AM] button.
Each time the button is pressed the Wallpaper scan is turned
ON and OFF.
7 Start downloading
Press the [4] or [¢] button for at least 2 seconds.
"Downloading" is displayed.
When the downloading finishes, "Finished Download" is
displayed.
2 Select the wallpaper.
Press the [4] or [¢] button.
Each time the button is pressed the wallpaper changes.
3 Exit Display Control mode
Press the [S.A] button.
Picture download may take as long as 10 minutes.
Quantity
Gradation Level
Picture downloading
Downloading movies and wallpapers. Downloaded pictures can
be used for the display of this unit.
— 18 —
Download from Www.Somanuals.com. All Manuals Search And Download.
When you would like to cancel
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken with you,
helping to deter theft.
Press the [MENU] button.
8 Exit the downloading mode
Press the [MENU] button.
Removing the Faceplate
• Do not operate this unit, while "Data Writing" is displayed, to
prevent data from being damaged.
• The number of files that can be downloaded.
- Downloaded movie: 1 file
- Wallpaper: 1 file
• When a new movie is downloaded, it is overwritten to the
currently downloaded movie.
1 Press the Release button.
Drop open the faceplate.
2 Drawing the faceplate to left side pull it to the front and
remove it.
Also, when a new wallpaper is downloaded, it is overwritten to
the currently downloaded wallpaper.
Note! There is no way to delete the downloaded pictures.
• The downloaded pictures can be used for display.
<Display switching part for "Display Type C" and "Display Type D">
(page 16)
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate in
its special storage case while detached.
• Do not expose the faceplate or its storage case to direct sunlight
or excessive heat or humidity. Also avoid places with too much
dust or the possibility of water splashing.
<Wallpaper selecting> (page 18)
• When you can't download the pictures to this unit, there may be a
problem with the CD-R/CD-RW write method.
Refer to the URL
rewrite the CD-R/CD-RW.
Reattaching the Faceplate
1 Align the shaft on the unit with the depression on the
faceplate.
Non-fading Output
Turning the Non-fading output ON or OFF.
Press the [NF] button for at least 1 second.
Each time the button is pressed Non-fading output switches ON
or OFF.
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use the unit.
When it’s ON, "NF ON" is displayed.
— 19 —
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
6 Repeat steps 3 through 5 and enter the name.
Station/Disc Naming (SNPS/DNPS)
7 Exit name set mode
Attaching a title to a Station or CD.
Press the [NAME.S] button.
1 Receive/play the station/disc you want to attach a title to
• When operation stops for 10 seconds the name at that time is
registered, and Name Set mode closes.
• Memory numbers
• A title can't be attached to a MD.
• Disc Naming can't be done during CD text or MP3/WMA text
display in the Character information display part b.
- FM: 32 stations
- AM: 16 stations
- Internal CD player: 30 discs
- External CD changer/ player: Varies according to the CD changer/
player. Refer to the CD changer/ player manual.
• The title of station/CD can be changed by the same operation
used to name it.
2 Enter name set mode
Press the [NAME.S] button for at least 2 seconds.
"Name Set" is displayed.
3 Move the cursor to the enter character position
Press the [4] or [¢] button.
4 Select the character type
Press the [38] button.
Each time the button is pressed the character type switches as
shown below.
Character type
Auxiliary Input Display Setting
Alphabet upper case
Alphabet lower case
Numbers and symbols
Special characters (Accent characters)
Selecting the display when this device is switched to internal
and optional Auxiliary input sources.
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX" display.
5 Select the characters
Press the [FM] or [AM] button.
2 Enter Auxiliary input display setting mode
Press the [NAME.S] button for at least 2 seconds.
The presently selected AUX Name is blinks.
Characters can be entered by using a remote with a number
buttons.
Example: If "DANCE" is entered.
Character
Button
#Times pressed
3 Select the Auxiliary input display
Press the [4] or [¢] button.
Each time the button is pressed it switches through the below
displays.
"D"
"A"
"N"
"C"
"E"
[#3]
[#2]
[#6]
[#2]
[#3]
1
1
2
3
2
— 20 —
Download from Www.Somanuals.com. All Manuals Search And Download.
• The Dual Zone System can be used with the optional Auxiliary
input sources shown below.
- KCA-S210A
• "AUX"
• "TV"
• "VCP"
• "GAME"
• "PORTABLE"
• "DVD"
- CA-C1AX
- CD changer with an Auxiliary input function installed.
The Dual Zone System cannot be used in the built-in Auxiliary input.
• This function can be used in Auxiliary input source.
• The front channel and rear channel can be set to be the internal
source or the Auxiliary input source. Refer to the <Dual Zone
System Setting> (page 36).
4 Exit Auxiliary input display setting mode
Press the [NAME.S] button.
When operation stops for 10 seconds, the name at that time is
selected, and Auxiliary input display setting mode closes.
Dual Zone System
Makes the sound different for the front channel and rear
channel.
One side of both the front and rear channels outputs the internal
source sound, and the other side outputs the Auxiliary input
source sound.
Press the [S.A] button for at least 1 second.
Each time the button is pressed for at least 1 second Dual Zone
System switches ON or OFF.
When it’s ON, "Zone 2 ON" is displayed.
• When the Dual Zone System is ON, there is no Auxiliary input
source channel audio control or other effect.
• When the Dual Zone System is being used the internal source
channel can't be used with an External disc source.
• When you set the Dual zone system to ON while the non-fading
preout is switched ON, the sound of the non-fading preout isn’t
output.
— 21 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner features
Tuning Mode
Choose the tuning mode.
4
¢
FM
Press the [AUTO] button.
Each time the button is pressed the Tuning mode switches as
shown below.
Tuning mode
Display
Operation
Auto seek
Preset station
seek
"Auto1"
"Auto2"
Automatic search for a station.
Search in order of the stations
in the Preset memory.
Manual
"Manual"
Normal manual tuning control.
AM
#1 #6
SRC
AUTO/
AME
Tuning
Selecting the station.
Frequency display
ST indicator
1 Select tuner source
Press the [SRC] button.
Select the "TUNER" display.
2 Select the band
Press the [FM] or [AM] button.
Each time the [FM] button is pressed it switches between the
FM1, FM2, and FM3 bands.
3 Tune up or down band
Press the [4] or [¢] button.
• During reception of stereo stations the "ST" indicator is ON.
• The sound will be temporarily muted while the faceplate is
opening.
The display above is an example when Display type is set to "Display Type A".
The function indicator is displayed only if it is "Display Type A".
— 22 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Access Tuning (Function of remote)
Auto Memory Entry
Entering the frequency and tuning.
Putting stations with good reception in the memory
automatically.
1 Select the band
Press the [FM] or [AM] button.
1 Select the band for Auto Memory Entry
Press the [FM] or [AM] button.
2 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote.
"– – – –" is displayed.
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in the memory
Auto Memory Entry closes.
3 Enter the frequency
Press the number buttons on the remote.
Example:
Desired frequency
Press button
92.1 MHz (FM)
810 kHz (AM)
[#0], [#9], [#2], [#1]
[#0], [#8], [#1], [#0]
Canceling Direct Access Tuning
Preset Tuning
Calling up the stations in the memory.
Press the [DIRECT] button on the remote.
1 Select the band
Press the [FM] or [AM] button.
2 Call up the station
Press the [#1] — [#6] button.
Station Preset Memory
Putting the station in the memory.
1 Select the band
Press the [FM] or [AM] button.
2 Select the frequency to put in the memory
Press the [4] or [¢] button.
3 Put the frequency in the memory
Press the [#1] — [#6] button for at least 2 seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the memory on each [#1]
— [#6] button.
— 23 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner features
RDS features
SNPP (Station Name Preset Play)
(Function of Remote)
¢
FM
Selecting the stations to display SNPS.
1 Enter SNPP mode
Press the [DNPP] button on the remote.
When "SNPP" is displayed, SNPS displays the FM1, FM2, FM3
and AM bands in order.
If the station has no name, the frequency or program service name
is displayed instead.
4
Changing the display order
Press the [4] or [¢] button.
AM
#1 #6
PTY
DISP
Changing the displayed band
Press the [FM] or [AM] button.
2 If the station you want is displayed
Press the [OK] button on the remote.
The displayed SNPS station is received.
Canceling the SNPP mode
Radio text
Program Service name
Press the [DNPP] button on the remote.
The display above is an example when Display type is set to "Display Type A".
The function indicator is displayed only if it is "Display Type A".
— 24 —
Download from Www.Somanuals.com. All Manuals Search And Download.
23. Personality
24. Public
25. College
26. Weather
"Personality"
"Public"
"College"
"Weather"
PTY (Program Type)
Selecting the Program Type and searching for a station.
1 Enter PTY mode
Press the [PTY] button.
"PTY Select" is displayed.
• Speech and Music include the Program type below.
Speech: No.3 — 6, 20, 22 — 26
Music: No.7 — 19, 21
This function can't be used during a traffic bulletin or AM reception.
• The Program Type can be put in the [#1] — [#6] button memory
and called up quickly. Refer to the <Program Type preset> (page
26).
2 Select the Program Type
Press the [FM] or [AM] button.
3 Search for the selected Program Type station
Press the [4] or [¢] button.
No. Program Type
Display
1.
2.
3.
4.
5.
6.
7.
8.
9.
Speech
Music
News
"All Speech"
"All Music"
"News"
When you want to search for other stations press the [4] or
[¢] button again.
When the selected Program Type isn't found, "NO PTY" is displayed.
Select another Program Type.
Information
Sports
"Information"
"Sports"
4 Exit PTY mode
Press the [PTY] button.
Talk
"Talk"
Rock
"Rock"
Confirming the Program Type
Press the [DISP] button.
Classic Rock
Adult Hits
10. Soft Rock
11. Top 40
"Classic Rock"
"Adult Hits"
"Soft Rock"
"Top 40"
The Program Type is displayed for 5 seconds.
12. Country
13. Oldies
"Country"
"Oldies"
14. Soft
"Soft"
15. Nostalgia
16. Jazz
"Nostalgia"
"Jazz"
17. Classical
18. R & B
19. Soft R & B
20. Language
21. Religious Music
22. Religious Talk
"Classical"
"Rhythm & Blues"
"Soft R & B"
"Foreign Language"
"Religious Music"
"Religious Talk"
— 25 —
Download from Www.Somanuals.com. All Manuals Search And Download.
RDS features
Registration of a station as a PTY
Radio Text Scroll
Registering a Program Type for stations with no PTY data.
Scrolling the displayed radio text.
Press the [DISP] button for at least 1 second.
1 Receive the station you want to register
The following parts show texts that can be scrolled.
- Character information display part b
Refer to <Display switching part for "Display Type A" and "Display
Type B"> (page 13).
Refer to <Display switching part for "Display Type C" and "Display
Type D"> (page 16).
2 Select the Program Type to register
Refer to <PTY(Program Type)> (page 25).
3 Register the Program Type
Press the [NAME.S] button for at least 2 seconds.
4 Exit PTY mode
Press the [PTY] button.
Program Type preset
Putting the Program Type in the Preset button memory and
calling it up quickly.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY(Program Type)> (page 25).
2 Preset the Program Type
Press the [#1] — [#6] button for at least 2 seconds.
Calling up the preset Program Type
1 Enter PTY mode
Refer to <PTY(Program Type)> (page 25).
2 Call up the Program Type
Press the [#1] — [#6] button.
— 26 —
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA/External disc control features
Release button
FM
¢
4
RDM
F.SEL
AM
SCAN
M.RDM
REP
DISP
SRC
Track title/ Disc title
Folder name/ File name/ MP3/WMA text
IN indicator
The display above is an example when Display type is set to "Display Type A".
The function indicator is displayed only if it is "Display Type A".
— 27 —
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA/External disc control features
Playing CD & MP3/WMA
When there is no disc inserted
1 Drop open the faceplate
Press the Release button.
2 Insert a disc.
3 Press the faceplate on the right side, and return it to its
former position.
3 Press the faceplate on the right side, and return it to its
• When the faceplate has been dropped open, it might interfere
with the shift lever or something else. If this happens, pay
attention to safety and move the shift lever or take an appropriate
action, then operate the unit.
• Do not use the unit with the faceplate in the open condition. If it's
used in the open position dust can enter the inside part and cause
damage.
former position.
3 in. (8cm) disc can't be played. Using an adapter and inserting them
into this unit can cause damage.
The MP3/WMA media that this unit can play are CD-ROM, CD-R,
and CD-RW.
The medium formats must be ISO 9660 Level 1, Level 2, Joliet, or
Romeo. The methods and precautions to be followed for writing
MP3/WMA data are covered in <Notes on playing MP3/WMA>
(page 6).
When a disc is inserted, the "IN" indicator is ON.
Check that section before creating your MP3/WMA media.
When a disc is inserted
Press the [SRC] button.
Select the "Compact Disc" display.
Pause and play
Press the [38] button.
Each time the button is pressed it pauses and plays.
Playing External Disc
Playing discs set in the optional accessory disc player connected
to this unit.
Eject the disc
1 Drop open the faceplate
Press the Release button.
Press the [SRC] button.
Select the display for the disc player you want.
Display examples:
2 Eject the disc
Press the [0] button.
Display
Disc player
"Compact Disc2"
"DiscChanger"
CD player
CD changer/ MD changer
— 28 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Pause and play
Album Search
Selecting the disc set in the Disc changer or the folder recorded
on the MP3/WMA media.
Press the [38] button.
Each time the button is pressed it pauses and plays.
The functions that can be used and the information that can be
displayed will differ depending on the external disc players being
connected.
Press the [FM] or [AM] button.
Direct Track Search (Function of remote)
Doing Track Search by entering the track number.
Fast Forwarding and Reversing
Fast Forwarding
1 Enter the track number
Press the number buttons on the remote.
Hold down on the [¢] button.
Release your finger to play the disc at that point.
2 Do Track Search
Reversing
Press the [4] or [¢] button.
Hold down on the [4] button.
Release your finger to play the disc at that point.
Canceling Direct Track Search
Press the [38] button.
Track Search
Searching for a song on the disc or in the MP3/WMA folder.
Press the [4] or [¢] button.
— 29 —
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA/External disc control features
Track Scan
Direct Album Search
(Function of disc changers with remote)
Playing the first part of each song on the disc or MP3/WMA
folder you are listening to and searching for the song you want
to listen to.
Doing Disc Search by entering the disc number.
1 Enter the disc number
Press the number buttons on the remote.
1 Start Track Scan
Press the [SCAN] button.
"Scan ON" is displayed.
2 Do Album Search
Press the [DISC+] or [DISC–] button.
2 Release it when the song you want to listen to is played
Press the [SCAN] button.
Canceling Direct Album Search
Press the [38] button.
Random Play
Play all the songs on the disc or MP3/WMA folder in random
order.
Track/Album Repeat
Replaying the song, disc in the Disc changer or MP3/WMA folder
you're listening to.
Press the [RDM] button.
Each time the button is pressed Random Play turns ON or OFF.
When it's ON, "Random ON" is displayed.
Press the [REP] button.
Each time the button is pressed the Repeat Play switches as
shown below.
When the [¢] button is pressed, the next song select starts.
Repeat play
Display
Track Repeat (In CD/MD)
"Track Repeat ON"/
"Repeat ON"
(In MP3/WMA)
Album Repeat (In Disc Changer)
"File Repeat ON"
"Disc Repeat ON"
(In MP3/WMA media) "Folder Repeat ON"
"Repeat OFF"
Magazine Random Play
OFF
(Function of disc changer)
Play the songs on all the discs in the disc changer in random
order.
— 30 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the [M.RDM] button.
Selecting a folder in the same level
Each time the button is pressed the Magazine Random Play turns
ON or OFF.
When it's ON, "M.Random ON" is displayed.
Press the [4] or [¢] button.
With the [4] button you move to the previous folder, and with
the [¢] button to the next folder.
Returning to the top level
Press the [#3] button.
When the [¢] button is pressed, the next song select starts.
3 Decide the folder to play
Press the [38] button.
The Album Select mode releases, and the MP3/WMA in the
folder being displayed is played.
Album Select (Function of MP3/WMA)
Quickly selecting the folder you want to listen to.
The methods for moving to other folders in the album select mode
are different from those in the album search mode.
See <Notes on playing MP3/WMA> (page 6) for details.
1 Enter Album Select mode
Press the [F.SEL] button.
"Select Mode" is displayed.
Canceling the Album Select mode
Press the [F.SEL] button.
During Select mode the folder information is displayed as shown
below.
- Folder name display: Display the currently selected folder name.
- Folder number display: Displays the number in the folder belonging
to the currently selected folder.
Folder name display
Text/Title Scroll
Scrolling the displayed CD text, MP3/WMA text, or MD title.
Press the [DISP] button for at least 1 second.
The following parts show texts that can be scrolled.
Folder number display
2 Select the folder level
Press the [FM] or [AM] button.
With the [FM] button you move 1 level down and with the [AM]
button 1 level up.
- Character information display part b
Refer to <Display switching part for "Display Type A" and "Display
Type B"> (page 13).
Refer to <Display switching part for "Display Type C" and "Display
Type D"> (page 16).
— 31 —
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA/External disc control features
Menu system
DNPP (Disc Name Preset Play)
(Function of disc changers with remote)
Selecting the CD displayed in the DNPS of the CDs set in the
Disc changer.
¢
FM
1 Enter DNPP mode
Press the [DNPP] button on the remote.
When "DNPP" is displayed the DNPS display in order.
Forward / Reverse display
Press the [DISC–] or [DISC+] button.
4
2 When the disc you want is displayed
Press the [OK] button on the remote.
The disc being displayed is played.
AM
DISP
SRC
MENU
Canceling the DNPP mode
Press the [DNPP] button on the remote.
Menu display
— 32 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu System
Setting during operation beep sound etc. functions.
The Menu system basic operation method is explained here. The
reference for the Menu items and their setting content is after
this operation explanation.
1 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Press the [FM] or [AM] button.
Example: When you want to set the beep sound select the
"Beep" display.
3 Set the menu item
Press the [4] or [¢] button.
Example: When "Beep" is selected, each time the button is
pressed it switches "Beep :ON" or "Beep :OFF". Select
1 of them as the setting.
You can continue by returning to step 2 and setting other items.
4 Exit Menu mode
Press the [MENU] button.
When other items that are applicable to the basic operation method
above are displayed afterwards their setting content chart is
entered. (Normally the uppermost setting in the chart is the original
setting.)
Also, the explanation for items that aren't applicable (<Manual Clock
Adjustment>etc.) are entered step by step.
— 33 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
Press the Reset button and when it's removed from the
battery power source
Security Code <In Standby mode>
Because authorization by the Security Code is required when it's
removed from the vehicle, personalizing this unit is by using the
Security Code is a help in preventing theft.
1 Turn the power ON.
2 Do the step 4 through 7 operation, and enter the Security
Code.
"APPROVED" is displayed.
The unit can be used.
When the Security Code function is activated, the code can't be
changed and the function can't be released.
Note, the Security Code can be set as the 4 digit number of your
choice.
1 Enter Standby
Press the [SRC] button.
Select the "ALL OFF" display.
2 Enter Menu mode
Touch Sensor Tone
Setting the operation check sound (beep sound) ON/OFF.
Press the [MENU] button for at least 1 second.
When "MENU" is displayed, "Security" is displayed.
Display
Setting
3 Enter Security Code mode
Press the [4] or [¢] button for at least 1 second.
When "ENTER" is displayed, "CODE" is displayed.
"Beep :ON"
"Beep :OFF"
Beep is heard.
Beep canceled.
4 Select the digits to enter
Press the [4] or [¢] button.
5 Select the Security Code numbers
Press the [FM] or [AM] button.
6 Repeat steps 4 and 5, and complete the Security Code.
Manual Clock Adjustment
7 Confirm the Security Code
This adjustment can be done when the <Synchronize Clock> (page
35) is set as OFF.
Press the [¢] button for at least 3 seconds.
When "RE-ENTER" is displayed, "CODE" is displayed.
1 Select Clock Adjustment mode
Press the [FM] or [AM] button.
Select the "Clock Adjust" display.
8 Do the step 4 through 7 operation, and reenter the Security
Code.
"APPROVED" is displayed.
2 Enter Clock Adjust mode
Press the [4] or [¢] button for at least 1 second.
The clock display blinks.
The Security Code function activates.
When the wrong Code is entered in steps 4 through 6, repeat from
step 4.
— 34 —
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Adjust the hours
Press the [FM] or [AM] button.
Date Mode
Setting the date format.
Adjust the minutes
Press the [4] or [¢] button.
1 Select Date Mode
Press the [FM] or [AM] button.
Select the "Date Mode" display.
4 Exit Clock adjustment mode
Press the [MENU] button.
2 Select the date format
Press the [4] or [¢] button.
Date Adjustment
1 Select Date Adjust mode
Press the [FM] or [AM] button.
Select the "Date Adjust" display.
Synchronize Clock
Synchronizing the RDS station time data and this unit's clock.
Display
Setting
2 Enter Date Adjust mode
Press the [4] or [¢] button for at least 1 second.
The date display blinks.
"SYNC :OFF"
"SYNC :ON"
Adjust the time manually.
Synchronizes the time.
It takes 3 to 4 minutes to synchronize the clock.
3 Selecting the item (day, month, or year) to adjust
Press the [4] or [¢] button.
The items that are blinking are items that can be adjusted.
4 Adjust each item
Press the [FM] or [AM] button.
5 Repeat step 3 and 4 operation and adjust the date.
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the faceplate is
removed, warning potential thieves.
6 Exit Date adjustment mode
Press the [MENU] button.
Display
Setting
"DSI :ON"
"DSI :OFF"
LED flashes.
LED OFF.
— 35 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
Contrast Adjustment
Built-in Amp Mute Setting <In Standby mode>
Adjusting the display contrast.
Toggles ON or OFF the mute control on the built-in amplifier.
Turning ON this control enhances the preout quality.
Display and Setting
Display
Setting
"Contrast :0"
"AMP Mute :OFF"
"AMP Mute :ON"
The built-in amplifier activates.
The built-in amplifier deactivates.
"Contrast :1"
"Contrast :2" (Original setting)
"Contrast :3"
Dual Zone System Setting
<When the Dual Zone System is OFF >
Setting the Front channel and Rear channel sound when the
Dual Zone System is ON.
Dimmer
Dimming this unit's display automatically when the vehicle light
switch is turned ON.
Display
Setting
Display
Setting
"Dimmer :ON"
"Dimmer :OFF"
The display dims.
The display doesn't dim.
"Zone 2 :Rear" The front is this unit's internal source, and the
rear is Auxiliary input sound.
"Zone 2 :Front" The rear is this unit's internal source, and the
front is Auxiliary input sound.
System Q
Setting display/don't display for the System Q factors (Bass
center frequency, Bass Q factor, Bass extend, Middle center
frequency, Middle Q factor, and Treble center frequency) in
Audio control.
Display
Setting
"System Q :ON"
"System Q :OFF"
The System Q factors are displayed.
The System Q factors aren't displayed.
— 36 —
Download from Www.Somanuals.com. All Manuals Search And Download.
B.M.S. (Bass Management System)
Traffic Information
Adjust the bass boost level of the external amplifier using the
main unit.
Switching to traffic information automatically when a traffic
bulletin starts even when you aren't listening to the radio.
Display
Setting
Display
Setting
"AMP Bass Flat"
"AMP Bass +6"
"AMP Bass +12"
"AMP Bass +18"
Bass boost level is flat.
"TI :OFF"
"TI :ON"
The Traffic Information function is OFF.
The Traffic Information function is ON.
Bass boost level is low (+6dB).
Bass boost level is mid (+12dB).
Bass boost level is high (+18dB).
When a traffic bulletin starts, "Traffic Info" is displayed it and it
switches to traffic information.
• Refer to the catalog or instruction manual for power amplifiers that
can be controlled from this unit.
• For amplifiers there are the model that can be set from Flat to +18
dB, and the model that can be set from Flat to +12 dB.
When an amplifier that can only be set to +12 is connected to the
unit, "AMP Bass +18" won't work correctly even if it's selected.
• During reception of a AM station when the Traffic Information
function is turned on ON it switches to a FM station.
• During reception of traffic information the adjusted volume is
automatically remembered, and the next time it switches to traffic
information it's automatically the remembered volume.
Receiving other traffic information stations (In tuner
source)
Press the [4] or [¢] button.
Traffic information station switching can be done when listening to
the radio.
B.M.S. Frequency Offset
Setting the central frequency boosted by B.M.S.
Display
Setting
CRSC (Clean Reception System Circuit)
<In FM reception>
Temporarily have reception switched from stereo to mono to
reduce multi-path noise when listening to the FM station.
"AMP Frq :Normal"
"AMP Frq :Low"
Boost with the normal central frequency
Drop the normal central frequency 20%
Display
Setting
"CRSC :ON"
"CRSC :OFF"
The CRSC is ON.
The CRSC is OFF.
Strong electrical fields (such as from power lines) may cause
unstable sound quality when CRSC is turned ON. In such a situation,
turn it OFF.
— 37 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
Basic Operations of remote
Text Scroll
Setting the displayed text scroll.
Display
Setting
"Scroll :Auto"
Repeats scroll.
"Scroll :Manual"
Scrolls when the display changes.
The text scrolled is shown below.
• CD text
• Folder name/ File name/ MP3/WMA text
• MD title
• Radio text
Built-in Auxiliary input Setting
Set the Built-in Auxiliary Input function.
Display
Setting
"AUX IN :OFF" When selecting the source there's no Auxiliary
Input.
"AUX IN :ON" When selecting the source there's Auxiliary
Input.
Picture downloading <In Standby mode>
For the setting method refer to the <Picture downloading> (page
18).
— 38 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and Replacing the battery
In Tuner source
Use one lithium battery (CR2025).
Insert the batteries with the + and – poles aligned properly,
following the illustration inside the case.
[FM]/ [AM] buttons
Select the band.
Each time the [FM] button is pressed it switches between the
FM1, FM2, and FM3 bands.
[4]/ [¢] buttons
Tune up or down band.
[#0] — [#9] buttons
Press buttons [#1] — [#6] to recall preset stations.
[DIRECT] button
Enters and cancels the <Direct Access Tuning> (page 23) mode.
2WARNING
Store unused batteries out of the reach of children. Contact a doctor
immediately if the battery is accidentally swallowed.
[38] button
Enters and cancels the <PTY (Program Type)> (page 25) mode.
[DNPP]/ [OK] button
Do not set the remote on hot places such as above the dashboard.
Enters and cancels the <SNPP (Station Name Preset Play)> (page
24) mode.
Basic operations
[VOL.] buttons
Adjusting the volume.
[SRC] button
Each time the button is pressed the source switches.
For the source switching order refer to <Selecting the Source>
(page 9).
[ATT] button
Turning the volume down quickly.
When it is pressed again it returns to the previous level.
— 39 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations of remote
In Disc source
[4]/ [¢] buttons
Doing track forward and backward.
[DISC+]/ [DISC–] buttons
Doing album forward and backward.
[38] button
Each time the button is pressed the song pauses and plays.
[DNPP]/ [OK] button
Enters and cancels the <DNPP (Disc Name Preset Play)> (page
32) mode.
[#0] — [#9] buttons
When in <Direct Track Search> (page 29) and <Direct Album
Search> (page 30), enter the track/disc number.
— 40 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
External view
External view
......... Number of items
2WARNING
......... Number of items
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
1
2
3
4
5
.........4
.........4
.........2
.........1
.........2
2CAUTION
• If your car's ignition does not have an ACC position, connect the
ignition wires to a power source that can be turned on and off
with the ignition key. If you connect the ignition wire to a power
source with a constant voltage supply, as with battery wires, the
battery may die.
• If the console has a lid, make sure to install the unit so that the
faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching to
cause a short circuit, then replace the old fuse with one with the
same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps on
the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to which
they correspond. The unit may be damaged or fail to work if you
share the - wires or ground them to any metal part in the car.
• When only two speakers are being connected to the system,
connect the connectors either to both the front output terminals
or to both the rear output terminals (do not mix front and rear).
For example, if you connect the + connector of the left speaker
to a front output terminal, do not connect the - connector to a
rear output terminal
The use of any accessories except for those provided might result in
damage to the unit. Make sure only to use the accessories shipped with
the unit, as shown above.
Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and
disconnect the - battery.
2. Make the proper input and output wire connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following order: ground,
battery, ignition.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
— 41 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Front right output (Red) 28
AUX left input (White)
AUX right input (Red)
Front left output (White) 23
Non-fading right output (Red) 27
Rear left output (White)
Rear right output (Red)
Non-fading left output (White) 26
To KENWOOD disc changer/
DAB control input/KPA-SD100/
KPA-HD100/KPA-SS100
To connect the Disc changer, consult your
Disc changer manual. 3
FM/AM antenna input 1
If no connections are made, do not let the wire come out from the tab.
4
Fuse (10A) 24
5 When using the optional power amplifier,
Wiring harness
(Accessory1)25
connect to its power control terminal.
Power control wire (Blue/White) 15
7 Depending on what antenna you are using,
connect either to the control terminal of the
motor antenna, or to the power terminal for
the booster amplifier of the film-type antenna.
Motor antenna control wire (Blue)
29
17
White/Black
To front left
speaker 30
8 To "EXT.AMP.CONT." terminal of the amplifier
External amplifier control wire
(Pink / Black) 20
White
31
having the external amp control function.
32
Gray/Black
To car light control switch
To front right
speaker 33
Dimmer control wire (Orange / White)
18
8
Gray
34
35
Ignition key
switch
10
Green/Black
To rear left
speaker 36
Ignition wire (Red) 20
ACC 13
Green
37
38
Purple/Black
Car fuse box
(Main fuse)
11
Battery wire (Yellow) 21
Car fuse
box 14
To rear right
speaker 39
Purple
40
Ground wire (Black) · (To car chassis) 22
–
+
Battery 12
— 42 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
■ Installation
■ Installing in Japanese-Made Cars
1 Refer to the section "Removing the hard rubber frame" (page 44)
and then remove the hard rubber frame.
Firewall or metal support
2 Align the holes in the unit (two locations on each side) with the
vehicle mounting bracket and secure the unit with the accessory
screws.
Screw (M4X8)
(commercially
available)
N
T
8 mm
8mm
MAX.
MAX.
N
T/N
3
T
4
ø5mm
ø5mm
Bend the tabs of the
mounting sleeve
with a screwdriver or
similar utensil and
attach it in place.
T: Toyota cars
N: Nissan cars
Accessory3...for Nissan car
Accessory4 ...for Toyota car
• During installation, do not use any screws except for those provided.
The use of different screws might result in damage to the main unit.
• Damage may occur if a screwdriver or similar tool is used with
excessive force during the installations.
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Make sure that the unit is installed securely in place. If the unit is
unstable, it may malfunction (for example, the sound may skip).
■ Screwing the Faceplate on the Unit
If you want to fasten the
faceplate to the main unit so
that it does not fall off,
screw in the provided
Accessory5
Bottom panel
screws (ø2.6 × 12 mm) in
the holes shown below.
Never insert the taptite screw (ø2.6 × 12 mm) in any other screw hole
than the one specified. If you screw it in another hole, it will contact
and may cause damage to the mechanical parts inside the unit.
— 43 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
■ Removing the hard rubber frame
■ Removing the Unit
1 Refer to the section “Removing the hard rubber frame” and then
remove the hard rubber frame.
1 Engage the catch pins on the removal tool and remove the two
locks on the lower level.
Lower the frame and pull it forward as shown in the figure.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots on each side,
as shown.
Catch
Lock
Accessory2
Screw (M4X8)
Removal tool
(commercially
available)
Accessory2
Removal tool
2 When the lower level is removed, remove the upper two
locations.
4 Lower the removal tool
toward the bottom, and pull
out the unit halfway while
pressing towards the inside.
Be careful to avoid injury from
the catch pins on the removal
tool.
5 Pull the unit all the way out
with your hands, being
careful not to drop it.
The frame can be removed from the top side in the same manner.
— 44 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
? Even if Loudness is turned ON, high-pitched tone isn't compensated
for. 17
✔
Tuner source is selected.
☞ High-pitched tone isn't compensated for when in Tuner source.
? The Bass center frequency, Bass quality factor, Bass extend, Middle
center frequency, Middle quality factor, and Treble center frequency
can’t be adjusted.19
General
? The power does not turn ON.01
✔
The <System Q> (page 36) is set OFF.
✔
The fuse has blown.
☞ Set it ON.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
? No sound can be heard, or the volume is low.
✔
The fader or balance settings are set all the way to one side.21
☞ Center the fader and balance settings.
✔
No ACC position on vehicle ignition.02
☞ Connect the same wire to the ignition as the battery wire.
✔
The input/output wires or wiring harness are connected incorrectly.22
☞ Reconnect the input/output wires or the wiring harness correctly.
See the section on <Connecting Wires to Terminals>.
? Nothing happens when the buttons are pressed.04
✔
The computer chip in the unit is not functioning normally.
☞ Press the reset button on the unit (page 5).
✔
The values of Volume offset are low.24
☞ Increase the values of Volume offset. (page 11)
? There’s a source you can’t switch.06
✔
There’s no CD inserted.
? The sound quality is poor or distorted.25
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
✔
One of the speaker wires is being pinched by a screw in the car.
☞ Check the speaker wiring.
✔
The Disc changer isn’t connected.08
✔
The speakers are not wired correctly.27
☞ Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
☞ Connect the Disc changer. If the Disc changer isn’t connected to
it's input terminal, You can't switch to an external disc source.
? The faceplate does not open or close.09
? Non-fading output, Non-fading Low Pass Filter and Non-fading
✔
The faceplate is incorrectly attached.
setting can’t be done.28
☞ Reattach the faceplate correctly, See the section on <Removing
the Faceplate>(page 19).
✔
The <Non-fading output> (page 19) is OFF.29
☞ Turn it ON.
? The memory is erased when the ignition is turned OFF.10
✔
The <Dual zone system> (page 21) is ON.30
☞ Turn it OFF.
✔
The battery wire has not been connected to the proper terminal.
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
✔
The ignition and battery wire are incorrectly connected.11
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? There’s no loudness effect.12
✔
You’re using Non-fading preout.
☞ Loudness has no effect in Non-fading preout.
— 45 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Tuner source
? There’s no Front High Pass Filter and Rear High Pass Filter effect.31
✔
The Non-fading preout is being used.
? Radio reception is poor.39
☞ There’s no effect in Non-fading preout.
✔
✔
The car antenna is not extended.
☞ Pull the antenna out all the way.
? The Security Code item isn’t displayed in the Menu System.32
✔
The Security Code function is already activated.
☞ When the Security Code function is activated it isn’t displayed in
the menu items.
The antenna control wire is not connected.40
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? The Touch Sensor Tone doesn’t sound.34
? The desired frequency can’t be entered with the Direct Access
✔
The preout jack is being used.
Tuning.41
☞ The Touch Sensor Tone can’t be output from the preout jack.
✔
A station that can’t be received is being entered.
☞ Enter a station that can be received.
? Even though the vehicle light switch is turned ON, the unit’s display
✔
You’re trying to enter a frequency with a 0.01 MHz unit.42
☞ What can be designated in the FM band is to 0.1 MHz.
won’t dim.36
✔
The dimmer wire isn’t connected.
☞ Connect the dimmer wire correctly.
? It isn't the set Traffic information sound volume. 43
✔
The set sound volume is less than the tuner sound volume.
☞ If the tuner sound volume is louder than the set sound volume,the
tuner sound volume is used.
? The Dimmer function doesn’t work. 38-1
✔
The Dimmer wire isn’t connected correctly.
☞ Check the Dimmer wire connection.
✔
The <Built-in Amp Mute Setting> (page 36) is ON.100
☞ Turn it OFF.
? AUX cannot be selected. 103
✔
<Built-in Auxiliary input Setting> is turned off.
☞ Refer to the <Built-in Auxiliary input Setting> (page 38) in the
menu setting and turn on the <Built-in Auxiliary input Setting> .
— 46 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Disc source
? A CD ejects as soon as it is loaded.62
✔
The CD is upside-down.
? "AUX" is displayed without achieving External disc control mode.50
☞ Load the CD with the labeled side up.
✔
✔
O-N switch is set to "O" side.
✔
The CD is quite dirty.63
☞ Set the switch to "N" side.
☞ Clean the CD, referring to the section on <CD cleaning> (page 8).
Unsupported disc changer is connected.51
☞ Connect the supported disc changer. (page 4)
? Can’t remove disc.64
✔
The cause is that more than 10 minutes has elapsed since the vehicle
ACC switch was turned OFF.
? The specified disc does not play, but another one plays instead.52
✔
✔
✔
The specified CD is quite dirty.
☞ The disc can only be removed within 10 minutes of the ACC
switch being turned OFF. If more than 10 minutes has elapsed,
turn the ACC switch ON again and press the Eject button.
☞ Clean the CD.
The CD is upside-down.53
☞ Load the CD with the labeled side up.
? The disc won’t insert.65
The disc is loaded in a different slot from that specified.54
☞ Eject the disc magazine and check the number for the specified
disc.
✔
There’s already another disc inserted.
☞ Press the [0] button and remove the disc.
? Direct Track Search and Direct Album Search can’t be done.66-1
✔
The disc is severely scratched.55
✔
Another function is ON.
☞ Try another disc instead.
☞ Turn Random Play or other functions OFF.
? The specified track will not play.58
? Track Search can't be done.66-2
✔
Random play or magazine random play has been selected.
☞ Turn off random play or magazine random play.
✔
For the albums first or last song.
☞ For each album, Track Search can't be done in the backward
direction for the first song or in the forward direction for the last
song.
? Cannot play CD-R or CD-RW.60
✔
Finalization processing is not being conducted for CD-R/CD-RW.
☞ Conduct finalization processing with CD recorder.
✔
A non-compatible CD changer is being used to play the CD-R/CD-
RW.61
☞ Use a CD changer compatible with CD-R/CD-RW to play.
— 47 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
MP3/WMA source
? Can't display the ID3 tag information correctly.75
✔
Record is not made in conformity with the ID 3 tag version1.x.
? Cannot play an MP3/WMA.67
☞ Record in conformity with the ID 3 tag version1.x.
✔
Not conforming to ISO 9660 Level 1/2, Joliet, and Romeo.
☞ Use a medium conforming to ISO 9660 Level 1/2, Joliet, and
Romeo.
? Can’t enter Album Select mode.101
✔
There’s no folder recorded in the MP3/WMA media.
☞ Use a media with levels.
✔
✔
The MP3/WMA has no or invalid track name extension.68
☞ Add the ".MP3/.WMA" extension to the MP3/WMA track name.
? The songs in the selected folder aren’t played in Album Select
The media is scratched or dirty.69
mode.102
☞ Clean the media, referring to the section on <CD cleaning> (page
✔
There are no MP3/WMA in the selected folder.
8).
☞ Make sure there’s recorded content in the MP3/WMA media.
✔
The CD-RW is used with the quick format.
?The MP3/WMA track/album search takes time.78
☞ Select the full format to use CD-RWs.
✔
Many tracks are recorded on the media.
☞ When the media directory is complex, the track/album search can
take time.
? Noise or no sound generated when an MP3/WMA is played.70
✔
The track has the MP3/WMA track name extension while it is not an
MP3/WMA.
☞ Do not use the ".MP3/.WMA" extension in non-MP3/WMA.
? The MP3/WMA related text isn’t displayed correctly.79
✔
A character is entered that this unit can't display.
☞ For the characters that can be used for MP3/WMA text entry,
refer to <Notes on playing MP3/WMA> (page 6).
? Takes time before the unit starts playing MP3/WMA.71
✔
The medium contains many albums, tracks, and hierarchical levels.
☞ The unit checks all tracks on the loaded medium first. If the
medium has many tracks recorded, it may take a long time for the
unit before it starts playing MP3/WMA.
? The MP3/WMA track time isn’t displayed correctly.80
✔
---
☞ There are times when it isn’t displayed correctly according to the
MP3/WMA recording conditions.
? Fails to play MP3/WMA in the intended order.72
✔
The MP3/WMA tracks were not written by the CD writer in the order
in which you wanted them to be played.
☞ Depending on the CD writer, you may be able to set the order in
which MP3/WMA tracks are to be played by writing them onto a
medium with their track names beginning with play sequence
numbers such as "01" to "99".
? The sound skips when an MP3/WMA is being played.73-1
✔
The media is scratched or dirty.
☞ Clean the media, referring to the section on <CD cleaning> (page
8).
✔
The recording condition is bad.73-2
☞ Record the media again or use another media.
— 48 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Mecha Error: Something is wrong with the disc magazine. Or the
unit is malfunctioning for some reason.E99
The messages shown below display your systems
condition.
➪ Check the disc magazine. And then press the reset
button on the unit. If the "Mecha Error" code does
not disappear, consult your nearest service center.
Eject:
No disc magazine has been loaded in the changer.
The disc magazine is not completely loaded.E01
➪ Load the disc magazine properly.
No CD in the unit.
Hold Error:
NO NAME:
The protective circuit in the unit activates when the
temperature inside the automatic disc changer
exceeds 60°C (140°F), stopping all operation.E0d
➪ Cool down the unit by opening the windows or
turning on the air conditioner. As the temperature
falls below 60°C (140°F), the disc will start playing
again.
➪ Insert the CD.
No Disc:
No disc has been loaded in the disc magazine.E02
➪ Load a disc into the disc magazine.
TOC Error:
No disc has been loaded in the disc magazine.E04
➪ Load a disc into the disc magazine.
The CD is quite dirty. The CD is upside-down. The CD
is scratched a lot.
• Attempted to display DNPS during the CD play
having no disc names preset.E51
➪ Clean the CD and load it correctly.
• Attempted to display SNPS during the receiving
session of the station having no station name
preset.E50
E-05:
The CD is upside-down.E05
➪ Load the CD correctly.
NO TITLE:
NO TEXT:
Attempted to display the disc title or track title while
Blank Disc:
Nothing has been recorded on the MD.E10
the MD having no MD title is being played.E53
No Track Disc: No tracks are recorded on the MD, although it has a
• Attempted to display the disc text or track text
while the CD having no CD text is being played.E54
• Attempted to display text during reception of the
station that isn't sending text data.E55
• Attempted to display the ID3 tag or contents
description while the MP3/WMA having no ID3 tag
or contents description is being played. E52
title.E11
No Music Data:
Media was played that doesn’t have data recorded
that the unit can play. E15
➪ Use media that has data recorded that the unit can
play.
Files for picture downloading only are recorded in
CD-R/CD-RW.
Waiting:
Load:
Radio text data is being received.E56
Discs are being exchanged in the Disc changer.E57-1
The unit is reading the data on the disc.E57-2
No Panel:
E-77:
The faceplate of the slave unit being connected to
this unit has been removed.E30
➪ Replace it.
Reading:
NO ACCESS: After setting it in the Disc Changer, DNPP was done
The unit is malfunctioning for some reason.E77
➪ Press the reset button on the unit. If the "E-77"
code does not disappear, consult your nearest
service center.
without having it been played at least 1 time.E58
— 49 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
IN (Blink):
The CD player section is not operating properly.E59
➪ Reinsert the CD. If the CD cannot be ejected or the
display continues to flash even when the CD has
been properly reinserted, please switch off the
power and consult your nearest service center.
Unsupported File:
A WMA is played with a format that this unit can't
support.E63
Protected File: A copy-protected file is played.E64
Can’t Download:
Download Error:
This unit does not work properly for some reason.
➪ Press the reset button to download it again. If this
error is still displayed, consult a local Kenwood
dealer.
No Display Data File:
No file that can be downloaded is contained in the
CD-ROM.
➪ Make sure that a files created with referring to
yId=3> is contained in the CD-ROM.
Do not delete the extension (.kbm) created when
the file was created.
Incorrect File: The file selected to be downloaded has a format that
this unit cannot read.
➪ Recreate the file.
Writing Error: Writing failed while the file was downloaded.
➪ Try the downloading again.
— 50 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz
Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)
Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)
Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz
Signal to Noise ratio (MONO)..............................................70 dB
Selectivity ( 400 kHz).......................................................≥ 80 dB
Stereo separation (1 kHz) ....................................................40 dB
Maximum output power.................................................50 W x 4
Full Bandwidth Power (at less than 1% THD) ...............22 W x 4
Tone action
Bass : ..............................................................100 Hz 10 dB
Middle : .............................................................1 kHz 10 dB
Treble : ............................................................10 kHz 10 dB
Preout level / Load (during disc play)....................4500 mV/10 kΩ
Preout impedance.................................................................80 Ω
AM tuner section
Frequency range (10 kHz space) ...................530 kHz – 1700 kHz
Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)
Auxiliary input
Frequency response ( 1 dB).................................20 Hz – 20 kHz
Input Maximum Voltage .........................................................1.2 V
Input Impedance...............................................................≥ 44 kΩ
CD player section
Laser diode....................................................GaAlAs (λ=780 nm)
Digital filter (D/A)......................................8 Times Over Sampling
D/A Converter .......................................................................1 Bit
Spindle speed ..(CD-DA/MP3/WMA)1000 – 400 rpm (CLV 2times)
Wow & Flutter........................................Below Measurable Limit
Frequency response ( 1 dB).................................10 Hz – 20 kHz
Total harmonic distortion (1 kHz) ......................................0.01 %
Signal to Noise ratio (1 kHz) ................................................96 dB
Dynamic range ....................................................................95 dB
Channel separation..............................................................90 dB
MP3 decode ......Compliant with MPEG-1.0/2.0/2.5 Audio Layer-3
WMA decode...................Compliant with Windows Media Audio 8
General
Operating voltage (11 – 16V allowable) .............................14.4 V
Current consumption.............................................................10 A
Installation Size (W x H x D) .........................180 x 50 x 159 mm
7-1/16 x 1-15/16 x 6-1/4 inch
Weight.................................................................3.08 lbs (1.4 kg)
— 51 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|