Use & Care Guide
Model: 122.16134110
Kenmore
®
Liquid Propane
Gas Grill
P/N 19000343A1 (1110)
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
™
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
• Have your LP gas tank filled by a reputable
propane gas dealer and visually inspected and re-
qualified at each filling.
• Do not store a spare LP gas tank under or
• near this appliance.
A tank of approximately 12 inches in diameter by 18-1/2
inches high is the maximum size LP gas tank to use.
You must use an OPD gas tank which offers an
Overfill Prevention Device.
• Never fill the tank beyond 80 percent full . If this
information is not followed exactly a fire causing
death or serious injury may occur.
This safety feature prevents the tank from being
overfilled which can cause malfunction of the LP gas
tank, pressure regulator and/or grill.
• Always keep LP gas tanks in an upright position.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this gas grill.
• Do not subject the LP gas tank to excessive heat.
• Never store an LP gas tank indoors. If you store
your gas grill in the garage or other indoor
location, always disconnect the LP gas tank first
and store it safely outside.
The LP gas tank must be constructed and marked in
accordance with specifications of the U.S. Dept. of
Transportation (DOT). In Canada, the LP gas tank must
meet the National Standard of Canada ,CAN/CSA-B339 ,
Cylinders , spheres and Tubes for Transportation of
Dangerous Goods and Commission .
Always keep the LP cylinder at
90° (upright) orientation to
provide vapor withdraw.
1. The LP gas tank must have a shutoff valve,
terminating in an LP gas supply tank valve outlet, that is
compatible with a Type 1 tank connection device. The LP
gas tank must also have a safety relief device that has a
direct connection with the vapor space of the tank.
2. The tank supply system must be arranged for vapor
withdraw.
• Place dust cap on cylinder valve outlet whenever
the cylinder is not in use. Only install the type of
dust cap on the cylinder valve outlet that is
provided with the cylinder valve. Other types of
caps or plugs may result in leakage of propane.
• LP gas tanks must be stored outdoors in a well-
ventilated area and out of reach of children.
Disconnected LP gas tanks must not be stored in
a building, garage or any other enclosed area.
• When your gas grill is not in use the gas must be
turned off at the LP gas tank.
• The pressure regulator and hose assembly must
be inspected before each use of the grill. If there
is excessive abrasion or wear or if the hose is cut,
it must be replaced prior to the grill being used
again.
• Keep the gas pressure regulator hose away from
hot grill surfaces and dripping grease. Avoid
unnecessary twisting of hose. Visually inspect the
hose prior to each use for cuts, cracks, excessive
wear or other damage. If the hose appears
damaged do not use the gas grill. Call 1-800-4-
MY-HOME for a replacement hose.
• Never light your gas grill with the lid closed or
before checking to ensure the burner tubes are
fully seated over the gas valve orifices.
3. The LP gas tank used must have a collar to protect the
tank valve.
Proper Placement and Clearance of Grill
Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area. Your gas grill is
to be used outdoors only, at least 24 inches from the
back and side of any combustible surface. Your gas grill
should not be used under overhead combustible
construction . Do not obstruct the flow of ventilation air
around the gas grill housing.
• Do not install this outdoor gas grill in or on recreational
vehicles or boats
• Keep outdoor gas grill area clear and free from
combustible materials, gasoline and other flammable
vapors and liquids
• Do not obstruct the flow of combustion and ventilation
air. Check for this each time prior to using grill.
• Never connect an unregulated LP gas tank to your gas
grill. The gas pressure regulator assembly supplied with
your gas grill is adjusted to have an outlet pressure of 11”
water column (W.C.) for connection to an LP gas tank.
• Only use the pressure regulator and the hose assembly
supplied with your gas grill. Replacement pressure
regulators and hose assemblies must be those specified
in this manual.
• Never allow children to operate your grill.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner Flame Check
WARNING
!
A strong gas smell, or the hissing sound of gas
indicates a serious problem with your gas grill or
the LP gas tank. Failure to immediately follow the
steps listed below could result in a fire or
explosion that could cause serious bodily injury,
death, or property damage.
• Shut off gas supply to the gas grill.
• Turn the control knobs to OFF position.
• Put out any flame with a proper fire extinguisher.
• Open Grill Lid.
• Get away from the LP gas tank.
Visually check the burner flames prior to each use. The
flames should look like picture, if they do not, refer to the
cleaning burner tubes and ports, see page 15 of this
manual.
• Do not try to fix the problem yourself.
• If odor continues or you have a fire you can not
extinguish, call your fire department. Do not call
near the LP gas tank because your telephone is
a form of electrical device and could create a
spark resulting in fire and/or explosion.
Repair Protection Agreements
Congratulations on making a smart purchase. Your new
Kenmore product is designed and manufactured for
years of dependable operation. But like all products, it
may require repair from time to time. That's when having
a Repair Protection Agreement can save you money and
aggravation.
Here’s what the Repair Protection Agreement *
includes:
Expert service by our 10,000 professional repair
specialists
NOTE: The normal flow of gas through the pressure
regulator and hose assembly can create a humming
noise. A low volume of noise is perfectly normal and
will not interfere with operation of the grill. If humming
noise is loud and excessive you may need to purge
air from the gas line or reset the pressure regulator
excess gas flow device. This purging procedure
should be done every time a new LP gas tank is
connected to your grill. For help with this procedure
refer to page 16, Item 4 of “If Grill Still Fails To Light”,
or call the Grill Information Center at 1-800-913-8999.
Unlimited service and no charge for parts and labor
on all covered repairs
Product replacement up to $1500 if your covered
product can’t be fixed
Fast help by phone - we call it Rapid Resolution -
phone support from a Sears representative. Think of
us as a “talking owner’s manual”
CAUTION: Beware of Flash-Back
Once you purchase the Repair Protection Agreement, a
simple phone call is all that it takes for you to schedule
service. You can call anytime day or night, or schedule a
service appointment online.
The Repair Protection Agreement is a risk-free purchase.
If you cancel for any reason during the product warranty
period, we will provide a full refund. Or, a prorated refund
anytime after the product warranty period expires.
Purchase your Repair Protection Agreement today!
Some limitations and exclusions apply. For prices
and additional information in the U.S.A. call 1 -800-
827-6655.
CAUTION: Spiders and small insects occasionally
spin webs or make nests in the grill burner tubes
during transit and warehousing. These webs can lead
to gas flow obstruction which could result in a fire in
and around burner tubes. This type of fire is known as
“FLASH-BACK” and can cause serious damage to
your grill and create an unsafe operating condition for
the user.
Although an obstructed burner tube is not the only
cause of “FLASH-BACK”, it is the most common
cause.
To reduce the chance of “FLASH-BACK”, you must
clean the burner tubes before assembling your grill,
and at least once a month in late summer or early fall
when spiders are most active. Also perform this
burner tube cleaning procedure if your grill has not
been used for an extended period of time.
*Coverage in Canada varies on some items. For Full
details call Sears Canada at 1-800-361-6665
Sears Installation Service
For Sears professional installation of home appliances,
garage door openers, water heaters, and other major
home items, in the U.S.A. or Canada call 1-800-4-MY-
HOME.
See Cleaning Burner Tubes and Ports on page # 18.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CONTENTS LIST
A. Firebox--------1pc.
B. Bottom panel----1pc.
C. Tank Tray Bolt---1pc.
D. Swivel Caster with Brake---1pc.
E. Swivel Caster---------1pc.
F. Caster----------2pcs.
G. Side Panel, Left-----1pc.
H. Side Panel, Right-----1pc.
I. Back panel----1pc.
J. Gas Tank Barrier Bar---1pc.
K. Door handle-----2pcs.
L. Door, Left------1pc.
M. Door Right-----1pc.
N. Side Burner bowl assembly frame
O. Left side shelf with side
with Side burner control panel-----1pc. shelf front panel---------1pc.
P. Heat Diffuser--------4pcs.
R. Cooking Grid---2pcs.
S. Warming Rack-------1pcs.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
T. Bezel---------------------------1 pc
U.. Control Knob-------------1 pc
X. Grease Cup----------------1pc
V.1.5 Volt “AA” Size Alkaline
Battery----------1pc.
W. Grease Tray -----1pc.
Y. Manual Lighting Stick-----1pc.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Pack Contents
Item
AA
Description
Specification
1/4 x 15mm
Quantity
16 pcs
Phillips Head Screw
Phillips Head Screw
Phillips Head Screw
Flat Head Screw
BB
CC
DD
1/4 x 10mm
5/32 x 8mm
5/32 x 8mm
14 pcs
19pcs
8 pcs
Flat Washer
Lock Washer
EE
FF
1/4
1/4
4pcs
26pcs
15 pcs
Lock Washer
Hex Wrench
GG
5/32
HH
5/64
1pc
Preparation
Before beginning assembly, make sure all parts are present. Compare parts with package contents list and
diagram above. If any part is missing or damaged, do not attempt to assemble the product. Contact
customer service for replacement parts.
•Tools required for Assembly.
Phillips Screwdriver
Wrench
Phillips Screwdriver (not included) and Wrench (not included)·
• Note: The left and right sides of the grill are on your left and right as you face the front of the grill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 122.16134110 Parts diagram
0 2
0 3
0 4
0 1
0 5
5 7
0 6
0 7
0 2
5 6
0 6
0 6
5 3
5 5
5 2
5 1
5 4
0 8
5 0
0 6
4 9
4 8
1 0
1 1
1 6
1 7
4 6
4 5
1 8
0 9
12
1 3
1 4
1 5
3 7
5 8
4 7
1 9
4 4
4 3
4 2
4 1
2 0
4 0
2 3
3 9
3 8
2 1
2 6
2 5
2 8
2 2
3 0
3 1
2 9
2 4
2 7
2 7
3 3
3 0
3 0
3 5
3 6
3 3
3 4
3 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 122.16134110 Parts List
QUANTIT
Y
KEY# PARTS
DESCRIPTION
QUANTITY KEY# PARTS
DESCRIPTION
1
2
0773-001 Main Lid
0773-002 Main Lid Screw
1
2
30
31
0773-030 Door Hinge
4
1
0773-031 Front Door, Left
3
4
0773-003 Temperature Gauge Housing
0773-004 Temperature Gauge
0773-005 Logo
1
1
1
4
1
1
1
1
1
1
1
32
33
34
35
36
37
38
39
40
41
42
0773-032 Front Door, Right
1
2
1
1
1
1
1
1
1
1
1
1
0773-033 Door Handle
5
0773-034 Lighting Rod
6
0773-006 Hood Buffer
0773-035 Lighting Rod Cover
0773-036 Gas Tank Barrier Bar
0773-037 control panel support bracket, Right
0773-038 Back Panel
7
0773-007 Main Lid Handle
0773-008 Flange, Left
8
9
0773-009 Flange, Right
10
11
12
13
0773-010 control panel support bracket, left
0773-011 Pulse Igniter Module
0773-012 Regulator, LP
0773-039 Back Panel, Top
0773-040 Side Burner Gas Valve
0773-041 Side Burner Front Panel
0773-042 Side Burner Pipe Assembly
0773-013 Side Manifold
14 0773-014 Side Burner Flex Gas Line
1
43 0773-043 Side Burner Igniter Wire
15
0773-015 Main Manifold
1
44
0773-044 Side Burner Bowl Assembly
1
16
17
18
19
20
21
22
23
24
25
0773-016 Main Control Panel
0773-017 Bezel
1
5
5
1
1
1
1
1
1
1
45
46
47
48
49
50
51
52
53
54
0773-045 Side Burner Cooking Grate
0773-046 Side Burner Lid
1
1
1
1
1
1
1
1
1
4
0773-018 Control Knob
0773-047 Gas Tank Heat Shield
0773-048 Grease Slide Panel
0773-049 Grease Box
0773-019 Side Shelf, Left
0773-020 Side Shelf Front Panel, Left
0773-021 Side Panel, Left
0773-022 Side Panel, Right
0773-023 Swivel Caster with Brake
0773-024 Swivel Caster
0773-050 Main Burner Igniter Wire A
0773-051 Main Burner Igniter Wire B
0773-052 Main Burner Igniter Wire C
0773-053 Main Burner Igniter Wire D
0773-054 Main Burner
0773-025 Bottom Panel, LP
26
27
28
29
0773-026 Tank Tray Bolt
0773-027 Caster
1
2
1
2
55
56
57
58
0773-055 Heat Diffuser
4
2
1
4
0773-056 Cooking Grid with Hole
0773-057 Warming Rack
0773-058 Main Gas Valve
0773-028 Cart Frame, Front
0773-029 Door Magnet
If you are missing hardware or have damaged
Important: Use only parts listed above. When ordering
parts after unpacking grill, call 1-800-913-8999 for parts, providing the following information:
replacements.
1. Model #
To order replacement parts after using grill, call:
1-800-4-MY-HOME®
2. Serial # (found inside the front panel of your grill)
3. Part Number (see PART# in chart)
4. Part Description
To make sure you obtain the correct replacement
parts for your Kenmore gas grill, please refer to
the part numbers on this page.
5. Quantity of parts needed
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 1
Assembly Instructions
C
CAUTION: While it is possible for one person to
assemble this grill, obtain assistance from another
person when handling some of the larger, heavier
pieces.
B
D
E
Note: Be sure to slide grease tray out of back of grill
head and remove all packaging from tray.
F
1. Use the parts list to check that all parts have been
included.
F
2. Inspect the grill for damage as you assemble it. Do not
assemble or operate the grill if it appears damaged. If there
are damaged or missing parts when you unpack the
shipping box, or you have questions during the assembly
process, call:
Fig. 2
G
For Assembly Questions, call 1-800-913-8999
8AM – 5 PM PST, Monday through Friday.
1. Assembling Grill Cart
H
(a) Loosen and take out the bolt (C) pre-assembled on the
inner side of bottom panel,and insert it from the back of the
bottom panel, see (Fig. 1).
Fig. 3
(b) Attach four casters to bottom panel (B) using (16) 1/4
x15mm Phillips head screws (AA), (16) 1/4 lock washers
(FF). Note: (D) is swivel caster with brake, (E) is swivel
caster, (F) are straight casters. (Fig.1)
I
G
Note: Make sure the flat side of straight casters face out to
the exterior side when attaching. As shown in Fig.1.
Hint: For ease of caster assembly, turn bottom panel
upside down.
B
H
(c) Attach left & right side panels (G & H) to bottom panel
(B) using (4) 5/32 x 8mm Phillips head screws (CC) with (4)
5/32 lock washers (GG). (Fig.2)
Fig. 4
(d) Attach back panel (I) to bottom panel (B) using (3) 5/32
x 8mm Phillips head screws (CC) with (3) 5/32 washers
(GG). Attach back panel (I) to side panel (G&H) using (4)
1/4 x 10mm Phillips head screws (BB) with (4)1/4 lock
washers (FF) . (Fig.3)
J
(e) Attach gas tank barrier bar (J) to back panel (I) using (1)
5/32 x 8mm Phillips head screw (CC) and (1) 5/32 lock
washer (GG) from the back panel side. Attach bar to bottom
panel using same size screw and lock washer. (Fig. 4)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 5
(f) Attach door handle (K) to left door (L) using (2) 5/32 x
8mm Phillips head screws (CC). Repeat to assemble the
other door handle to right door (M). (Fig.5)
(g) Attach two doors (L & M) to side panels (G & H) using
(8) 5/32 x 8mm flat head screws (DD). (Fig. 6)
2. Firebox Assembly
L
K
M
(a) Be sure grill cart doors are closed to stabilize cart.
Remove grill head (A) from carton. Place onto cart from
above as shown in (Fig. 7)
CAUTION: Grill head is heavy. To avoid injury, obtain
the help of an assistant for this step. Also, make sure
doors remain closed when placing grill head onto
cart. DO NOT open doors until grill head is securely
mounted to cart.
Fig. 6
G
H
(b) Attach grill head (A) to left and right side panels (G &
H) using (6) 1/4 x 10mm Phillips head screws (BB) and (6)
lock washers (FF). (Fig. 8)
L
Fig. 7
A
Fig. 8
A
G
H
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Side Burner & Side Shelf Assembly
(a) Loosen (2) preinstalled 1/4 x 10mm Phillips head
screws from right side of grill head (A) as shown. Do
not screw out fully; leave ¼ extended for shelf
assembly. (Fig. 9)
Fig.9
A
(b) Through side burner shelf keyholes, hang side
burner shelf (N) on two loosened screws. (Fig. 10)
(c) Using (2) 1/4 x 10mm Phillips head screws (BB) and
(2) 1/4 flat washers (EE), attach side burner shelf (N) to
grill head from inside the firebox. Insert (1) 5/32 x 8
mm Phillips head screws (CC) and (1) 5/32 lock
washers (GG) to attach the side burner shelf front panel
to the control panel (Fig 11).Fully tighten the two
loosened screws to secure shelf to firebox.
(d) Repeat steps (a) through (c) to install side shelf.
Fig.10
N
Fig.11
N
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Side Burner Valve Assembly
Fig. 12
N
(a) Remove side burner grate from side burner shelf and
set aside. Remove the two Phillips head screws
attaching side burner (N) to shelf to make room to install
side burner valve. See (Fig.12)
(b) Remove two screws from side burner control valve
face. Insert side burner valve control stem through hole
in side burner control panel . Place side burner control
knob bezel (T) over side burner valve control stem.
Secure bezel to control panel and valve with 2 screws
removed above. (Fig . 13A1).
(c) Insert side burner tube over side burner valve orifice
(Fig. 13B1). Use the two previously removed side burner
screws to reattach side burner to side burner shelf.
Fig. 13
B1
(d) Push control knob (U) onto valve control stem, and
tighten use hex wrench. (Fig.14.)
(e) Plug ignition wire into igniter wire hanging from
electrode on underside of burner (Fig.15).
(f) Replace the side burner grate into the side burner
shelf.
T
A1
Fig. 14
U
Fig. 15
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Grease Cup Assembly
Fig.16
From the back, pull out grease tray (W), remove any
packaging materials from it, then insert grease cup (X) into
grease tray (W) as shown in (Fig.16). Push grease tray
back into grill.
6. Installing Cooking Components
(a) Place heat diffusers over burners as shown. Diffuser
ends insert into channels on front and back of firebox.
(Fig. 17)
w
X
(b) Evenly space cooking grates (R) on the ledge above
heat diffusers. (Fig.17)
Fig.17
S
To obtain sear marks in cooked meat, be sure to insert
grates so that side with four corner feet faces down.
R
P
(c) Insert legs of warming rack (S) into the holes in the top
of firebox side panels. (Fig.17)
7. Battery Assembly
(a) Unscrew the ignition battery cap. (Found at far left of
control panel)
(b) Install battery (V) into ignition box with positive terminal
facing outward.
Fig.18
(c) Replace the ignition battery cap after the battery has
been installed. (Fig. 18)
V
14
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connecting LP Gas Tank to LP Grill
Fig.19
(a) From front of the cart, place foot ring of 20 lb tank into
the hole in bottom panel. Make sure the tank valve is in
OFF position. Use the tank bolt to secure the tank in a
fixed position (Fig.19).
(b) Check the tank valve to ensure it has proper external
mating threads to fit the hose and pressure regulator
assembly provided.
(c) Make sure all burner valves are in OFF position.
(d) Inspect the valve connection port and pressure regulator
assembly. Look for damage or debris. Remove any debris.
Inspect hose for damage. Never use damaged or plugged
equipment.
Fig.20
pressure regulator
Connection
(e) When connecting pressure regulator and hose
assembly to tank valve, hand tighten quick coupling nut
clockwise to a full stop. (Fig.20) Do not use a wrench to
tighten because it could damage the quick coupling nut and
result in a hazardous condition.
(f) Slowly open tank valve fully (counterclockwise). Use a
soapy water solution to check all connections for leaks
before attempting to light your grill (see next page for gas
leak check instructions). If a leak is found, turn tank valve
off and do not use your grill until the leak is repaired.
Congratulations
Your Kenmore gas grill is now ready for use.
Before the first use and at the beginning of each
season (and whenever the LP gas tank has
been changed):
CAUTION: When the appliance is not in use, gas must
be turned off at the supply tank.
1. Read all safety, lighting and operating
instructions.
2. Check gas valve orifices, burner tubes and
burner ports for any obstructions.
3. Perform gas leak check according to
instructions found on next page of the manual.
DISCONNECTING THE LIQUID PROPANE
CYLINDER
Turn the grill burner valves “OFF” and make sure the
grill is cool.
Turn the Liquid Propane Cylinder valve “OFF” by
turning clockwise until it stops.
Detach the pressure regulator assembly from the
cylinder valve by turning the quick coupling nut
counterclockwise.
Place dust cap on cylinder valve outlet whenever the
cylinder is not in use. Only install the type of dust cap
on the cylinder valve outlet that is provided with the
cylinder valve. Other types of caps or plugs may
result in leakage of propane.
Important
Before cooking on your grill the first time, wash
cooking grids and cooking rack with warm ,
soapy water. Rinse and dry thoroughly. Season
with cooking oil regularly. After cooking is
completed, turn grill to HIGH setting for 3 to 5
minutes to burn off excess grease or food
residue.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Be sure all gas connections are securely
tightened.
Checking for LP gas leaks
4. Turn on gas supply.
5. Open the grill main lid.
6. Push and turn any main burner control knob to
HI position. Push Electronic Ignition button for
3 to 5 seconds to light burner.
Never test for leaks with a flame. Prior to first use, at
the beginning of each season, or every time your LP
gas tank is changed, you must check for gas leaks.
1. Make a 50/50 (soap/water) mild soap solution.
2. Turn the control knobs to full OFF position; then turn
gas ON at supply tank.
3. Apply the soap solution with a clean brush to all gas
connections. See below. If growing bubbles appear
in the solution the connections are not properly
sealed. Check each fitting and tighten or repair as
necessary.
Gas Connection Leak Check
7. If the burner does not light after 5 seconds, turn
knob to OFF. Turn gas OFF at LP tank and wait
5 minutes for gas to clear. Then turn gas ON at
tank and repeat step 5
8. If burner still does not light, see Match Lighting
section and If Grill Still Fails to Light section on
following page.
9. To light additional burners, turn burner knob(s)
to HI . Push and hold electronic ignition button
to light burner. Adjust knob(s) to desired setting.
4. If you have a gas connection leak you cannot repair,
turn gas OFF at supply tank, disconnect fuel line
from your grill and call 1-800-913-8999 or your gas
supplier for repair assistance.
5. Also apply soapy solution to the tank seams. See
below. If growing bubbles appear, shut tank OFF
and do not use or move it! Contact an LP gas
supplier or your fire department for assistance.
USING THE SIDE BURNER:
Inspect the gas supply hose prior to turning the gas
“ON”. If there is evidence of cuts, wear or abrasion,
it must be replaced prior to use. Do not use the
side burner if the odor of gas is present.
WARNING: Always keep your face and body as
far away from the burner as possible when
lighting.
Gas Tank Leak Check
LIGHTING INSTRUCTIONS FOR SIDE BURNER
1. Open side burner lid fully.
2. Push and turn side burner knob to
HI position.
Push and hold Electronic Ignition button for 3-5
seconds to light burner.
Grill Lighting Instruction
3. If the side burner does not light after 5 seconds,
turn knob to OFF. Turn gas OFF at LP tank and
wait 5 minutes for gas to clear. Then turn gas
ON at tank and repeat step 2.
4. If burner still does not light, see Match Lighting
section and If Grill Still Fails to Light Section on
following page.
Grill Lighting Instructions for Main Burners
1. Do not smoke while lighting grill or checking gas
supply connections.
2. Be sure that LP gas tank is sufficiently full.
WARNING
!
Failure to open grill lid during the lighting
procedure could result in a fire or explosion
that could cause serious bodily injury, death,
or property damage.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
!
WARNING
If Grill Still Fails To Light
Never lean over the grill cooking area while
lighting your gas grill. Keep your face and body
a safe distance (at least 18 inches) from the
cooking grid surface when lighting your grill by
match.
1. Check gas supply and connections for leaks. Check
that all wire connections are secure.
2. Repeat basic lighting procedure. If your grill still
fails to operate, turn the gas off at source, turn the
control knobs to OFF, then check the following:
Manually Lighting Your Grill by Match
1. Insert a match into the manual lighting stick.
• Misalignment of burner tubes over orifices
Correction: Reposition burner tubes over orifices.
2. Follow steps 1 through 5 of the Basic Lighting
Procedure.
• Plugged orifice
Correction: Remove burners from grill, carefully lift
each burner up and away from gas valve orifice.
Remove the orifice from gas valve and gently clear
any obstruction with a fine wire. Then reinstall all
orifices, burners, and cooking components.
3. Light the match and extend the lighting stick to
cooking grid surface.
4. Turn the desired control knob to the HI
position setting to release gas. The burner should
light immediately.
3. If an obstruction is suspected in grill burner valves,
please call for repair service at 1-800-4-MY-HOME.
4. If the grill still does not light you may need to purge
air from the gas line or reset the pressure regulator
excess gas flow device. Note: This procedure should
be done every time a new LP gas tank is connected to
your grill.
OFF
To purge air from your gas line and/or reset the
pressure regulator excess gas flow device:
• Turn all control knobs to the OFF position.
• Turn off the gas at the tank valve.
IGNITE / HI
LO
• Disconnect pressure regulator from LP gas tank.
• Let unit stand for 5 minutes.
• Reconnect pressure regulator to the LP gas tank.
• Turn the tank valve on slowly until ¼ to ½ open.
• Open the grill lid.
• Push and turn any control knob to HIGH.
• Turn control knobs to HIGH until all the burners are
lit
!
WARNING
• You may start to use the grill
Should a “FLASH-BACK” fire occur in/or
around the burner tubes, follow the instructions
below. Failure to comply with these instructions
could result in a fire or explosion that could
cause serious bodily injury, death, or property
damage.
5. If all checks or corrections have been made and
you still have questions about operating your gas grill,
call the Grill Information Center at 1-800-913-8999
• Shut off gas supply to the gas grill.
• Turn the control knobs to OFF position.
• Put out any flame with a proper fire extinguisher.
• Open grill lid.
• Once the grill has cooled down, clean the burner
tubes and burners according to the cleaning
instructions found on page 18.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Exterior Stainless Steel Surfaces
Weathering and extreme heat can cause exterior
stainless steel surfaces to turn tan in color. Machine oils
used in manufacturing process of stainless steel can also
cause this tanning color. Use a stainless steel cleaner to
polish stainless steel surfaces of your grill. Never use
abrasive cleaners or scrubbers because they will scratch
and damage your grill.
Cleaning and Maintenance
To ensure a proper working unit the following proper
care and maintenance is suggested.
Cleaning Cooking Grids
We suggest you wash your cooking grids in a mild
soap and warm water solution. You can use a wash
cloth or soft brush to clean your cooking grids.
Cleaning Burner Tubes and Burner Ports
To reduce the chance of “FLASH-BACK” the procedure
below should be followed at least once a month in late
summer or early fall when spiders are most active or
when your grill has not been used for a period of time.
Cleaning Heat diffusers
Periodically you should wash the heat diffusers in a
soap and warm water solution. Use a soft brush to
remove stubborn burnt-on cooking residue. The heat
diffusers should be dry before you reinstall them.
1. Turn all burner valves and gas tank valve to off position.
2. Detach the LP gas pressure regulator assembly from
your gas grill.
3. Remove cooking grids, heat diffusers, and grease tray
from the grill.
Cleaning Grease Tray
The grease tray should be emptied and wiped down
periodically and washed in a mild detergent and warm
water solution. A small amount of sand or cat litter may
be placed in bottom of grease tray to absorb the grease.
Check the grease tray frequently, don’t allow excess
grease to accumulate and overflow out of the grease
tray.
4. Remove the screws from the underside of each burner
and lift the burners up and away from the gas valve orifice.
5. Using a bent stiff wire in the shape of a hook , air hose
or a bottle brush, run it through the burner tube and inside
several times to remove any debris.
6. Replace burners, see illustration below.
Step 1. Remove screw which locks ignite wire.
Step 2. Take off R clip which fixes burner at the end side.
Step 3. Locate the new burner onto the orifice.
(a) Insert the burner over the main burner gas valve .
(b) Make sure the orifice stud (C1) is inside the burner
venture (D1) as shown in (Fig.23).
Annual Cleaning of Grill Interior
Burning-off the grill after every use will keep it ready for
your next use. However, once a year you should give
the entire grill a thorough cleaning to keep it in top
operating condition. Follow these steps.
Step 4. Secure the main burner on the back wall use R
clip, and fix on ignite wire.
1. Turn all burner valves to full OFF position.
2. Turn LP gas tank valve to full OFF position.
3. Detach LP gas hose and pressure regulator
assembly from your gas grill. Inspect for any damage
and replace as necessary with manufacturer
replacement part number found on parts list.
4. Remove and clean heat diffusers, cooking grids and
grill burners.
5. Cover each gas valve orifice with aluminum foil.
6. Brush inside and bottom of grill with a nylon brush,
and wash with a mild soap and warm water solution.
Rinse thoroughly and let dry.
7. Remove the aluminum foil, then reinstall heat
diffusers, and cooking grids.
Fig. 23
D1
8. Reconnect gas source and observe burner flame for
correct operation.
Cleaning Exterior Surface
C1
We suggest you wash your grill using a mild soap and
warm water solution. You can use a wash cloth or
sponge for this process. Do not use abrasives or a
brush that might remove finish during the cleaning
process.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
!
WARNING
2. Clean any clogged ports with a stiff wire, such as
an open paper clip.
The location of the burner tube with respect to the
orifice is vital for safe operation. Check to ensure the
orifice is inside the burner tube before using the gas
grill. If the burner tube does not fit over the valve
orifice, lighting the burner may cause explosion
and/or fire.
3. Inspect each burner for damage (cracks or holes)
and if such damage is found, order and install a new
burner. After installation check to ensure that gas
valve orifices are correctly placed inside the ends of
the burner tubes.
Regardless of which burner cleaning procedure you
use, we recommend you also complete the following
steps to help prolong burner life.
WARNING
!
Spiders and insects can nest inside the burners of
the grill and disrupt gas flow. This very dangerous
condition could cause a fire behind the valve panel,
thereby damaging the grill and making it unsafe
for operation. Inspect the grill at least twice a year.
1. Use a fiber pad or nylon brush to clean the entire
outer surface of each burner until free of food residue
and dirt.
Troubleshooting
BEFORE CALLING FOR SERVICE
If the grill does not function properly, use the following check list before calling for service.
You should inspect the burners at least once a year or immediately after any of the following
conditions occur:
PROBLEMS
Grill won’t light when the control knob is
rotated.
WHAT TO DO
Check to see if LP tank is empty.
Clean wires and/or electrode by rubbing
with alcohol and clean swab.
Wipe with dry cloth.
Make sure the wire is connected to
electrode assembly.
Do other burners on the unit operate?
Check to see if other burners operate. If
so, check the gas orifice on the
malfunctioning burner for an obstruction.
Burner flame is yellow or orange, in
combination with the odor of gas.
Refer to Clean Burner Tubes and Burner
Ports on page 19. If problem still exists,
please call 1-800-913-8999.
Low heat with knob in “HI” position.
Is the fuel hose bent or kinked?
Is the grill in a dusty area?
Is there adequate gas supply available?
If it is only one burner that appears low,
does the orifice or burner need cleaning?
Is the gas supply or gas pressure low?
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooking Instructions
Indirect Cooking
To cook indirectly, the food should be placed on
the left or right side of your grill with the burner lit
on the opposite side.
WARNING
!
Do not leave the grill unattended.
Your grill will get very hot. Never lean over
the cooking area while using your grill. Do not
touch cooking surfaces, grill housing. Grill Lid
or any other grill parts while the grill is in
operation, or until the grill has cooled down
after use. Failure to comply with these
Flare-ups
The fats and juices dripping from grilled food can
cause flare-ups. Since flare-ups impart a
favorably,distinctive taste and color to food cooked
cover an open flame, they should be accepted up
to a point. Nevertheless, uncontrolled flaring can
result in a ruined meal.
instructions may result in serious bodily injury.
Burn-off
Before cooking on your gas grill for the first time,
you will want to “burn off” the grill to eliminate any
odor or foreign matter. Just ignite the burners,lower
the Lid, and operate grill on the HIGH setting for 3 to
5 minutes.
Cooking Temperatures
High setting: Only use this setting for fast warm-
up,searing steaks or chops and for burning food
residue off the grill after cooking is complete. Never
use the HIGH setting for extended cooking.
Medium to Low Settings: Most recipes specify
medium to low settings, including all smoking,
rotisserie cooking and for cooking lean cuts such as
fish.
NOTE: Temperature settings will vary with the
temperature and the amount of wind outside your
home.
Direct Cooking
The direct cooking method can be used with the
supplied cooking grids and food placed directly over
the lit grill Burners. The method is ideal for searing
and whenever you want meat, poultry or fish to have
and open-flame barbecued taste. Deep frying and
smoking are also best cooked in this manner
because they require direct heat.
WARNING
!
Do not line the bottom of the grill housing with
aluminum foil, sand or any substance that will
restrict the flow of grease into the grease tray.
Failure to comply with these instructions could
result in a fire or explosion which could cause
serious bodily injury, death, or property
damage.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Grill Cooking Chart
FOOD
Weight or thickness Temperature
Time
Special instructions and tips
Slice or chop vegetables and dot with butter or
Vegetables
NA
Medium
8 to 20 minutes margarine. Wrap tightly in heavy duty foil. Grill
turning occassionally.
Wrap individually in heavy duty foil. Cook
40 to 60 minutes
Potatoes
Whole
Medium
rotating occassionally.
Pre heat grill for 15-20 minutes then sear
steaks on each side for two minutes. Next
grill 3 to 5 minutes on each side or until
desired doneness.
Meat/Steaks
1/2 to 3/4 inches
1/2 to 3/4 inches
High-Medium
Medium
4 to 15 minutes
Grill turning once when juices rise to the
surface or until desired amount of doneness.
Do not leave hamburgers unattended since a
Ground Meats
8 to 15 minutes
flare-up could occur quickly.
Grill turning occassionally. During last few
20 to 40 minutes minutes brush with barbecue sauce, turn
several times.
Ribs
1/2 or full rack
NA
Medium
Medium
Grill turning four times. 2-4 minutes on each of
Hot dogs
Poultry-Cut
5 to 10 minutes
four sides.
Grill turning occassionally. During last few
20 to 40 minutes minutes brush with barbecue sauce if desired,
turn several times.
1/4 to 1/2 pounds
Low or Medium
Use poultry stand and brush frequently as
Low or
1 to 1-1/2 hours
desired
Poultry Whole
Fish
2 to 3 pounds
3/4 to 1 inch
Use poultry stand and brush frequently as
Medium
40 to 60 minutes
desired
Grill turning once to desired doneness. Brush
with melted butter, margarine or oil.
Medium
8 to 15 minutes
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For troubleshooting, product manuals and expert advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada / TM Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros países
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
|