7973 Rev 06/07
Pump 103RS/DV
Instruction Manual
Thank you for joining the AeroBed® family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care, and maintenance instructions for your new AeroBed
product. Always instruct and supervise others on your bed’s proper use, maintenance, and safety.
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children can reach it. Do not use
in or around water.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 10 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between complete inflation and deflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located at the foot of the bed is closed. Bed should be stored with valve in the closed and latched
position. If the Quick Release Valve is open, close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve
cover to the right or left as it snaps into the valve opening.
This is the closed position.
Open Air Release Valve
Close Valve Using 2 Thumbs
3. Remove AC plug, cord, and One Touch® Comfort Control Wand from plastic bag and shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.25A (Note: 230VAC product
sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety feature. This plug
will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Push and hold inflation/firmer button on the One Touch® Comfort Control Wand for approximately 60 seconds to inflate your AeroBed to the
full (firmest) capacity. Bed will not over-inflate.
6. Lie on the bed and use the Comfort Control Wand to adjust the firmness to your desired level. For firmer bed, press inflate/firmer button.
For softer bed, press deflate/softer button.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush under weight.
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electrical outlet prior to deflation.
2. To deflate your AeroBed, open the Quick Air Release Valve at the foot of the bed. Deflation takes approximately 15 seconds.
3. Roll or fold the AC cord with wand control and secure it. Fold sides of bed into the center along its length. Tightly roll your
AeroBed around the pump towards the air release end. When the bed is completely rolled, push the Quick Air Release Valve
closed until it locks.
4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing your AeroBed under 50°F (10°C)
and over 100°F (38°C) may affect its performance and will not be covered under warranty.
CARE AND MAINTENANCE
1. Inspect your AeroBed prior to each use.
2. Keep your AeroBed away from any sharp objects. Large cuts or snags may not be repairable and will not be covered by your warranty.
3. When not in use, store your AeroBed in a clean, dry place out of extreme temperatures. Product must be at room temperature
4. Do not store your AeroBed folded inside sofa beds or roll-aways. This may cause damage to your bed and will void your prior to inflating.
5. In case of incidental damage to your bed, a repair patch has been included. Please follow repair instructions carefully.
Download from Www.Somanuals.com. All Manuals Search And Download.
|