COMPONENT
COMPOSANT
COMPONENTE
#690163
1/2" IMPACT WRENCH KIT INSTRUCTION MANUAL
MANUEL D’UTILISATION POUR CLÉ À CHOCS DE 1/2 PO
MANUAL DE INSTRUCCIONES PARA LA LLAVE
DE IMPACTO DE 1/2"
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA SÉCURITÉ, LE FONCTIONNEMENT ET LE
REMISAGE DE CE PRODUIT. LIRE, ÉTUDIER ET VEILLER À BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS
ET AUTOCOLLANTS APPOSÉS SUR LE PRODUIT AVANT DE L’UTILISER. NE PAS RESPECTER CES INSTRUCTIONS POURRAIT
ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS.
ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD, OPERACIÓN, MANTENIMIENTO Y ALMACE-
NAMIENTO DE ESTE PRODUCTO. ANTES DE USARLO, LEA Y COMPRENDA TODAS LAS PRECAUCIONES, ADVERTENCIAS,
INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO. DE LO CONTRARIO PODRÍA SUFRIR LESIONES GRAVES O CAUSAR DAÑOS
MATERIALES.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
POUR TOUTE QUESTION OU EN CAS DE PROBLÈME AVEC LE PRODUIT ALLTRADE, NE PAS LE RETOURNER AU MAGASIN OÙ IL
A ÉTÉ ACHETÉ. APPELER LE SERVICE APRÈS-VENTEAU 1-800-590-3723. AVANT D’APPELER, VEILLER À SE PROCURER LES
INFORMATIONS SUIVANTES : No. DE MODÈLE, DATE DE L’ACHAT ET ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE
PEUT RÉSOUDRE VOTRE PROBLÈME PAR TÉLÉPHONE. POUR TOUT COMMENTAIRE OU SUGGESTION, N’HÉSITEZ PAS À NOUS
APPELER OU NOUS CONTACTER PAR COURRIEL À L’ADRESSE : [email protected]. VOS COMMENTAIRES NOUS
SONT EXTRÊMEMENT PRÉCIEUX.
KAWASAKI™ EST UNE MARQUE DE COMMERCE DE KAWASAKI™
MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE
PAS CE PRODUIT THIS PRODUCT. LES QUESTIONS DES CONSOM-
MATEURS DOIVENT ÊTRE ADRESSÉES À :
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
KAWASAKI™ ES UNA MARCA REGISTRADA CON LICENCIA DE
KAWASAKI™ MOTORS CORP., E.U.A., QUE NO FABRICA NI
DISTRIBUYE ESTE PRODUCTO. LAS CONSULTAS DE LOS
CONSUMIDORES DEBEN DIRIGIRSE A:
PARA EL SERVICIO
PARA EL CONSUMIDOR
SI TIENE DUDAS O SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE, NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO
DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-590-3723. ANTES DE LLAMAR, TENGA A MANO LA SIGUIENTE
INFORMACIÓN: No. DE MODELO, FECHA DE COMPRA Y DIRECCIÓN DE LA TIENDA. UN REPRESENTANTE DE ALLTRADE PUEDE
RESOLVER SU PROBLEMA POR TELÉFONO. SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO, LLÁMENOS O ENVÍENOS
UN MENSAJE DE CORREO ELECTRÓNICO A. INFO@ALLTRADETOOLS.COM. SUS COMENTARIOS SON FUNDAMENTALES PARA
NOSOTROS.
1-800-590-3723
Printed in China
Imprimé dans la Chine French
Impreso en China Spanish
©COPYRIGHT 2005 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
690163 – 1/2" Corded Impact Wrench, Clé à chocs de 1/2 po, La llave
de impacto de 1/2"
Download from Www.Somanuals.com. All Manuals Search And Download.
WORK AREA
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
PERSONAL SAFETY
Some examples of these chemicals are:
• Lead from lead-based paints.
Stay alert, watch what you are doing, and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in
serious personal injury.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat or hearing protection must be used for appropriate conditions.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL USE AND CARE
SAFETY RULES FOR IMPACT WRENCHES
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Use only impact sockets. Non-impact sockets may shatter or break causing
injury and/or damage.
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Ensure fastener and/or system will withstand the level of torque generated
by the tool. Excessive torque may cause breakage and possible personal injury.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Always wear safety goggles or eye protection when using this tool. Use a dust
mask or respirator for applications which generate dust.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Do not grasp the tool or place your hands too close to the spinning anvil. Your
hand may be lacerated or may cause injury.
Secure the material being worked on. Never hold it in your hand or across your
legs. Unstable support can cause loss of control and injury.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
Position yourself to avoid being caught between the tool or side handle and walls
or posts. Should the socket or bit become bound in the work, the reaction torque
of the tool could crush your hand or leg.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Check to see that keys and adjusting wrenches are removed from the Impact
Wrench before switching the tool “ON”. Keys or wrenches can fly away at high
velocity striking you or a bystander.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used
on another tool.
When using the Impact Wrench, always maintain a firm grip on the tool with both
hands.
Keep the handle of the Impact Wrench dry, clean, and free from oil and grease.
Do not run the Impact Wrench while carrying it at your side. A spinning socket or
bit could become entangled with clothing and injury may result.
SERVICE
Tool service must be performed only by qualified repair personnel. Service or
Disconnect the plug from the power supply and place the switch in the locked or
“OFF” position before making any assembly adjustments, changing accessories,
performing any inspection, maintenance or cleaning procedures. Such preventive
safety measures reduce the risk of starting the tool accidentally.
maintenance by unqualified personnel may result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
Do not use the Impact Wrench if it has been damaged, left outdoors in the rain,
snow, wet or damp environments, or immersed in liquid.
Maintain labels and nameplates on the Impact Wrench. These carry important
information. If unreadable or missing, contact Alltrade for a replacement.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
OPERATING INSTRUCTIONS
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a “live” wire will also make
exposed metal parts of the tool “live” and shock the operator.
3
4
2
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
1
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
5
V
A
Hz
W
Kg
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
CONTROLS AND COMPONENTS:
1. Rocker Switch
2. Gear Enclosure
3. Brush Caps
4. Anvil
ACCESSORIES:
5. Impact Sockets (4)
6. Carbon Brushes (2) (not shown)
min
s
Grinding Wheels, etc.
No load speed
No-load Rotational Speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
COMPONENT
CARBON BRUSHES
MODEL NUMBER
690296
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ROCKER SWITCH AND DIRECTION OF ROTATION
• To rotate the Impact Wrench
in a clockwise direction, press
the lower portion of the
Rocker Switch.
MAINTENANCE AND CLEANING
Always UNPLUG the Impact Wrench from power source
before attempting cleaning or maintenance.
• To rotate the Impact Wrench
in a counter-clockwise
direction, press the upper
portion of the Rocker Switch.
CLOCKWISE
COUNTER-CLOCKWISE
This Impact Wrench is lubricated before it leaves the
factory. This lubrication should last for the life of the tool. No further
lubrication is required.
ROCKER
SWITCH
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Brushes will wear with use and should be inspected periodically by qualified
personnel. Unscrew the plastic caps on the sides of the motor housings to inspect
the spring and brush assembly. If the brushes are worn down to the line closest to
the spring, replace them immediately.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Never open the Impact Wrench case. Do not attempt to repair the Impact Wrench
yourself. Opening this tool will void your warranty.
INSTALLING / REMOVING SOCKET
When installing a socket,
ACCESSORIES
align the holes in the side
of the socket with the dent
pin. Press the socket on until
the dent pin engages in the hole.
To remove a socket, depress
the dent pin through the hole
using a small pointed object, and
pull the socket off.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
When removing the socket or bit
from the tool, avoid contact with
skin and use proper protective
gloves when grasping the socket,
bit or accessory. Accessories may
be hot after prolonged use.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
14
12
12
12
12
12
-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
SPECIFICATIONS
SPECIFICATIONS
Voltage
120V
60 Hz
Rated Current
No-Load Speed
Impacts Per Minute
Maximum Torque
7.0A
2100/min
2700
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #310-522-9008)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
220 ft.lbs.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Reciprocating Saws
Routers
Rotary Tools
Jigsaws
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
Circular Saws
Angle Grinders
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI(tm) power tool and no one else all
parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of three years from original date of purchase, except
that such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this Kawasaki(tm) power tool, including the battery, shall be effective
for only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Exclusions
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-310-522-9008 or toll free at 1-800-590-3723 for general repair
information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|