Jaguar
Vacuum Cleaners
Download from Www.Somanuals.com. All Manuals Search And Download.
KVC20/21/22
Issue 1/05
Features of your Kambrook JaguarVacuum (KVC22 shown)
15
19
12
11
9
14
7
8
1
13
5
6
16
17
2
18
3
20
10
4
1. Hose inlet connection point
2. Cord rewind foot pedal
3. On/off foot pedal
11. Motor protection filter (not shown)
12. 360 degree crush proof hose
13. Telescopic wand
4. Park tool
14. Turbo floor head (KVC22 only)
5. On board tool storage lid release lever 15. Hard floor brush (KVC21 only)
6. On board tool storage compartment
7. Dust bag compartment
16. Crevice tool & brush attachments
17. Variable power control
18. Cord storage outlet
19. Carry handle
8. Dust bag full indicator
9. Dust bag compartment opening
10. HEPA filter (KVC21/22)
20. Multi terrain floor tool
4 stage filter (KVC20)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To retract the cord push down on the
‘cord rewind’ pedal.
UsingYour Kambrook Jaguar
Vacuum Cleaner
IMPORTANT: HOLDTHE PLUG
END WHEN RETRACTINGTHE
CORDTO PREVENT IT FROM
STRIKINGYOU ORTHEVACUUM.
Remove all packaging from the unit, hose
and other accessories; ensure that you
have removed all of the accessories before
discarding the packaging.
ALWAYS ENSURETHATTHE
DUST BAG ANDTHE MOTOR
PROTECTION FILTER ARE
CORRECTLY FITTED. NEVER
OPERATE WITHOUTTHE DUST
BAG OR FILTERS IN PLACE.
Ensure that the dust bag and filters are
correctly fitted.
Locate the crush proof hose and push the
connection point into the hose inlet
connection on the top of the unit, until a
“click” sound is heard.
Connect the wide end of the metal wand
to the hose end, and push together firmly.
Variable Power Control
The variable power control slide switch is
located on the top of the vacuum cleaner.
Slide the control to the right for
Fit the floor tool to the narrow end of
the wand/s and push together firmly.
maximum power for vacuuming hard floor
and carpet surfaces. Slide the control to
the left at the minimum power level when
using the crevice and brush tools.
Fully extend the power cord by pulling
the power plug (situated at the rear of the
unit) out from the unit, until the
red/yellow tape on the cord is shown.
Crevice and brush tool
accessories
ENSURETHATYOU DO NOT
OVER EXTENDTHE POWER
CORD – DO NOT EXTEND PAST
THE RED/YELLOW WARNING
TAPE ONTHE CORD
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards.
Plug into a 230/240v power point and
switch the power on.
The brush tools can be used to vacuum
delicate surfaces and areas such as shelves
and venetian blinds.
To commence vacuuming push down on
the on/off foot pedal, at the top, rear of
the unit.
Set the variable temperature control
between minimum and medium power
when using the tool accessories.
When vacuuming is complete, push down
on the ‘on/off’ pedal to switch off.Turn
the power off at the outlet and then
remove the power cord from the power
outlet (when removing plug from the
power outlet grasp the plug not the cord).
Separate crevice and brush tools are
located inside the on-board tool storage
compartment.The opening for this
compartment is located directly below the
hose connection inlet.To open place a
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HINT: once the bag is inserted ‘puff-out’ the bag as
much as possible to ensure the full capacity of the
bag can be taken up.
finger inside the thumb groove and pull
the compartment lid upwards.
Turn off the vacuum cleaner when
changing any attachments.
When vacuuming fine dust particles, the
fine dust particles can clog the pores of
the dust bag and the dust bag indicator
will indicate full. If this happens the bag
could appear relatively empty, however
the bag will still need to be changed to
avoid strain on the motor.
Dust bag indicator and
changing the dust bag
The dust bag should be changed when full.
The dust bag indicator window will
gradually turn red as the bag fills up and
when the dust bag indicator displays ‘red’
it is time to change the dust bag.
NOTE:The bag compartment lid may not close if
the bag is not correctly fitted.
IMPORTANT: DO NOT USETHE
UNIT WITH OUT A DUST BAG
IN PLACE
Always switch appliance off, then switch off
at the power outlet and unplug the appliance
prior to replacing dust bags or filters.
To remove the dust bag, ensure the unit is
down on its wheels, remove the crush
proof hose and push the ‘Dust bag
compartment lid release lever’ underneath
the handle. Once the lid has released, pull
the top cover back.
Replacing filters
Filters must be cleaned from time to time
to remove the fine dust particles that have
been collected.This can be done by shaking
them; however after approximately 5 dustbag
changes the filters should be replaced.
To remove the bag, grasp the top of dust bag
and pull out, and dispose in a rubbish bin.
Motor protection filter
The motor protection filter must always
be in place when operating the vacuum
otherwise damage to the motor may occur
To place a new dust bag, take a fresh dust
bag and with the arrow (printed on the
material section of the dust bag) pointing
down slide the material down into the
dust bag holder, until it comes in contact
with the bottom of the holder.
To replace the motor protection filter –
Remove the dustbag or pull the bag
forward.The motor protection filter is
located at the rear, right hand side of this
inner chamber. Pull the plastic filter holder
upward to remove.
HEPA filter
Filter holder
Filter holder
Dust bag holder
Removable filter
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Always switch appliance off, then switch
off at the power outlet and then unplug
the appliance prior cleaning or replacing
either filter.
To clean the outside of the unit, wipe the
exterior with a soft, damp cloth. Never
use an abrasive cleaner.
Check and replace both the motor
protection and HEPA dust filters on a
regular basis.
From time to time hair, cotton and other
items may get caught in the brushes of the
floor head.To remove such items, take a
pair of scissors and cut across the cotton,
hair, etc to loosen, then gently pull to
remove.
NOTE: Do not continue to pull if the item/s does
not easily come out as this may permanently
damage the floor tools.
The Turbo brush (KVC22 only) should be
cleaned regularly for optimum performance.
Without regular cleaning the turbo head
may block and restrict the rapid
movement of the bristles.To clean the
bristles, take a pair of scissors and cut
across the cotton, hair, etc to loosen, then
gently pull to remove.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KAMBROOK
2YEAR REPAIR
WARRANTY
KAMBROOK warrants the purchaser
If the product includes one or a number of
against defects in workmanship and material, accessories only the defective accessory
for a period of 2 years from the date
of purchase (3 months commercial use).
or product will be replaced.
In the event of KAMBROOK choosing to
replace the appliance, the guarantee will
expire at the original date, ie. 12 months
from the original purchase date.
Guarantee and purchase receipt for this
product are to be retained as proof
of purchase and must be presented
if making a claim under the terms of the
KAMBROOK guarantee.
In Australia, this KAMBROOK Guarantee
is additional to the conditions and
guarantees which are mandatory as
implied by the Trade Practices Act 1974
and State Territory legislation.
KAMBROOK reserves the right to repair
the appliance within the warranty period.
Warranty does not apply to any defect,
deterioration, loss or injury or damage
occasioned by, or as a result of the misuse
or abuse, negligent handling or if the product
has not been used in accordance with the
instructions. Items subject to wear and
tear, such as filters, accessories and drive
belts, are not covered by this warranty.
The guarantee excludes breakages and
consumables.
For service, spare parts or product
information in Australia, please call
KAMBROOK on the customer Service
Line (free call) 1800 800 634.
For service, spare parts or product
information in New Zealand,
please call KAMBROOK New Zealand,
Greenmount, Auckland Phone 09 271 3980
Fax 0800 288 513. For spare parts phone
09 271 3980.
This warranty is void if there is evidence
of the product being tampered with by
unauthorised persons.
If claiming under this guarantee the product
must be returned to freight prepaid.
YOUR PURCHASE RECORD (Please complete)
Attach purchase receipt here.
DATE OF PURCHASE___________________________
MODEL NUMBER _____________________________
SERIAL NUMBER (If applicable) ___________________
Please don’t return purchase record
unless you are making a claim
PURCHASED FROM ___________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Kambrook 461 Plummer Street, Port Melbourne 3207, Australia
Customer Service Line (free call) 1800 800 634 Customer Service Fax 1800 621 337
Kambrook New Zealand, Private Bag 94411, Greenmount, Auckland, New Zealand
Customer Service Line/Spare Parts 09 271 3980 Customer Service Fax 0800 288 513
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the one illustrated in this book. Issue 1/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|