JaguarVacuum
Cleaners
Download from Www.Somanuals.com. All Manuals Search And Download.
KVC11/12/15/16
Issue 2/01
Features of your Kambrook KVC11 JaguarVacuum Cleaner
11
5
7
6
10
4
8
12
13
9
3
2
14
1
15
16
1. Carry handle
9. Carry strap connection tabs
2. Dust bag compartment lid release lever 10. 2 x wands
3. Hose inlet connection point
4. Crush proof hose
5. Dust bag indicator
6. On/off foot pedal
7. Micro filter
11. Finger tip suction control
12. Brush attachment
13. Crevice tool
14. Cord storage outlet
15. Floor head
8. Cord rewind foot pedal
16. Carry strap
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features of your Kambrook KVC12/15/16 JaguarVacuum Cleaners
8
11
6
9
5
7
10
4
12
13
14
3
2
1
16
15
17
1. Carry handle
10. Cord rewind foot pedal
11. Finger tip suction control
12. Telescopic wand (KVC16)
13. 2 x wands (KVC12,15)
14. Cord storage outlet
15. Floor head
2. Dust bag compartment lid release lever
3. Hose inlet connection point
4. On board tool storage compartment
5. Crush proof hose
6. Dust bag indicator
7. On/off foot pedal
16. Crevice tool
8. Variable power control (KVC15 & 16)
17. Brush tool
9. HEPA filter (KVC15 &16) Micro filter
(KVC12)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Plug into a 230/240v power point and
switch the power on.
UsingYour Kambrook Jaguar
Vacuum Cleaner
To commence vacuuming push down on
the on/off foot pedal, at the top, rear of
Remove all packaging from the unit, hose
and other accessories; ensure that you
have removed all of the accessories before
discarding the packaging.
the unit
.
For full suction power ensure that the
fingertip suction control cover (on the
hose handle) is closed.
Ensure that the dust bag and filters are
correctly fitted.
Variable Power Control (models
KVC15 and 16 only)
Locate the crush proof hose and push the
connection point into the hose inlet
connection on the top of the unit, until a
“click” sound is heard.
The variable power control slide switch
is located on the top of vacuum. Slide
the control to the ‘MAX’ position for
vacuuming hard floors and carpet
surfaces and to ‘MIN’ position when
using the accessory tools.
KVC11,12,15 only.
Connect the wands together by placing
the narrower end inside the wider end of
the other wand and push together firmly.
When vacuuming is complete, push down
on the ‘on/off’ pedal to switch off.
Model KVC16 only features a telescopic
adjustable height wand.To extend the
wand push the extension lever in the
direction of the arrow (printed on the
lever) and pull out the narrower tube to
the desired height.
Turn the power off at the outlet and then
remove the power cord from the power
outlet (when removing plug from the
power outlet grasp the plug not the cord).
To retract the cord push down on the
‘cord rewind’ pedal.
Connect the wide end of the connected
wands (or telescopic tube [KVC16]) on
to the hose end, and push together firmly.
IMPORTANT: HOLDTHE PLUG
END WHEN RETRACTINGTHE
CORDTO PREVENT IT FROM
STRIKINGYOU ORTHEVACUUM.
Fit the floor head to the narrow end of
the wand/s and push together firmly.
Fully extend the power cord by pulling
the power plug (situated at the rear of
the unit) out from the unit, until the
yellow tape on the cord is shown.
ALWAYS ENSURETHATTHE
DUST BAG ANDTHE MOTOR
PROTECTION FILTER ARE
CORRECTLY FITTED. NEVER
OPERATE WITHOUTTHE DUST
BAG OR FILTERS IN PLACE.
ENSURETHATYOU DO NOT
OVER EXTENDTHE POWER
CORD - DO NOT EXTEND PAST
THE RED WARNINGTAPE ONTHE
CORD
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Crevice and brush tool
accessories
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards.
Using the ParkTool feature
The vacuum features a 2-way park tool
feature, which allows you to easily store
the wands with the floor tool directly on
the vacuum body.This is ideal when storing
the vacuum or if you need to temporarily
‘park’ the vacuum while you are cleaning.
The brush tool can be used to vacuum
delicate surfaces and areas such as shelves
and venetian blinds.
To park the vacuum in the
upright (storage) position
The park tool attachment
hook, for upright storage is
located on the lower wand.
For models withVariable Power Control,
set between Minimum and Medium power
when using the tool accessories.
For models withoutVariable Power
Control, slide the Fingertip Suction
Control cover (located on the hose
handle) to the open position.
With the vacuum switched off
and unplugged from the power point, place
the vacuum on its end (in an upright
position), insert the park tool hook into
the park tool receptacle on the underside
of the vacuum body (located to the upper
right of the front
Models KVC12/KVC15 and KVC16
Separate crevice and brush tools are
located inside the on-board tool storage
compartment.The opening for this
compartment is located directly below the
hose connection inlet.To open place a
finger inside the thumb groove and pull
the compartment lid upwards.
wheel).
Note:The floor tool should
be attached and in contact
with the floor to give
stability, if correctly
Model KVC11 only
assembled.
The crevice tool with detachable
brush attachment can be stored
on the wand attachment for easy
access and storage.
To park the vacuum
in the horizontal position
The park tool attachment hook, to park
the vacuum in the horizontal position, is
located on the floor tool head (on the
wand connection point).
To use the crevice tool, detach
the brush attachment from the
top to reveal the crevice tool.When the
brush attachment is required, push the back
onto the top of the crevice tool until it is
firmly in place.
With the vacuum on the floor in a
horizontal position, hold the floor tool
head facing outwards
and insert the park
tool hook into the
park tool receptacle
located at the rear of
the unit.
Turn off the vacuum when changing any
attachments.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
To place a new dust bag, take a fresh dust
bag and with the arrow (printed on the
cardboard section of the dust bag)
Replacing dustbag and filters
Dust bag indicator and changing the
dust bag
pointing down, slide the cardboard down
into the dust bag holder, until it comes in
contact with the bottom of the holder.
HINT: once the bag is inserted ‘puff-out’ the bag as
much as possible to ensure the full capacity of the
bag can be taken up. When vacuuming fine dust
particles, the fine dust particles can clog the pores
of the dust bag and the dust bag indicator will
indicate full. If this happens the bag could appear
relatively empty, however the bag will still need to
be changed to avoid strain on the motor.
The dust bag should be changed when full.
The dust bag indicator window will
gradually turn red as the bag fills up and
when the dust bag indicator displays ‘red’
it is time to change the dust bag.
Always switch appliance to off, then switch
off at the power outlet, then unplug the
appliance prior to replacing dust bags or
filters.
To remove the dust bag, have the unit
down on its wheels, remove the crush
proof hose and then lift the ‘Dust bag
compartment lid release lever’ and pull
the top cover back (Fig. 1/2-A)
NOTE:The bag compartment lid may not close if
the bag is not correctly fitted.
IMPORTANT: DO NOT USETHE
UNIT WITH OUT A DUST BAG IN
PLACE
To remove the bag, grasp the top of dust
bag and pull out (Fig. 2-B), and dispose in a
rubbish bin.
Replacing filters
Filters must be cleaned from time to time
to remove the fine dust particles that have
been collected.This can be done by shaking
them, however after approximately 5
dustbag changes the filters should be
replaced.
Fig. 1. KVC11
A
Dust bag holder
B
Motor protection filter
The motor protection filter must always
be in place when operating the vacuum
otherwise damage to the motor may
occur.To replace the motor protection
filter - Remove the dustbag or pull the bag
forward.The motor protection filter is
located at the rear, right hand side of this
Filter holder
Fig. 2. KVC12/15/16
A
Filter holder
B
KVC12/15/16
Dust bag holder
Filter holder
Removable foam filter
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KVC11
Attaching the carry strap (KVC11)
Unclasp the attachment clip and thread
the flat edged piece through the carrying
handle, clip the two ends together.
Filter holder
Removable foam filter
inner chamber. Pull the plastic filter holder
upward to remove. Remove foam filter
from holder.
HEPA and Micro dust filter
Replacing the micro dust filter (models
KVC11 & 12) or HEPA filter (models
KVC15 &16) - Remove the filter cover at
the top rear of the vacuum by pulling up
on the back tab. Remove the filter from
the cover (KVC11) or remove from
cavity (KVC12/15/16),
Ensure that the strap has no twists and
connect the strap to the other end of the
unit by taking the two metal clips on the
strap and connect them to the two strap
connection tabs.
Above: KVC12/15/16
Below: KVC11
Strap connection tabs
When attaching the clips connect from
underneath the tab.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Always switch appliance to off, then switch
off at the power outlet, then unplug the
appliance prior cleaning or replacing
either filter.
To clean the outside of the unit, wipe the
exterior with a soft, damp cloth. Never
use an abrasive cleaner.
Check and replace both the motor
protection and micro dust filters on a
regular basis.
Turbo Brush Head (model KVC16
only)
The KVC16 comes with a specially
designedTurbo brush head ideal for picking
up pet hair and other difficult to vacuum
items.
Use the switch on top of the head for long
pile carpet
bare floors use
and for short pile and
.
From time to time hair, cotton and other
items may get caught in the brushes of the
Turbo Head and prevent it from spinning
around.To remove such items, take a pair
of scissors and cut the across the cotton,
hair etc. to loosen, then gently pull to
remove.
NOTE: Do not continue to pull if the item/s does
not easily come out as this may permanently
damage theTurbo Head.
KVC 11/12/15 FloorTool
Use the switch on top of the head for long
pile carpet
bare floors use
and for short pile and
.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Kambrook 4 Kingston Town Close Oakleigh,Victoria 3166,Australia
Customer Service Line (free call) 1800 800 634 Customer Service Fax 1800 621 337
Kambrook (New Zealand) Mono Place Ellerslie,Auckland, New Zealand
Customer Service Line/Spare Parts 0800 253 007 Customer Service Fax 0800 263 001
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the one illustrated in this book. Issue 2/01
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
10
Download from Www.Somanuals.com. All Manuals Search And Download.
KAMBROOK
12 MONTH
REPLACEMENT WARRANTY
If the product includes one or a number of
accessories only the defective accessory
or product will be replaced.
KAMBROOK warrants the purchaser
against defects in workmanship and
material, for a period of 12 months from
the date of purchase (3 months
commercial use).
In the event of KAMBROOK choosing to
replace the appliance, the guarantee will
expire at the original date, ie. 12 months
from the original purchase date.
Guarantee and purchase receipt for this
product are to be retained as proof of
purchase and must be presented if making
a claim under the terms of the
In Australia, this KAMBROOK Guarantee
is additional to the conditions and
guarantees which are mandatory as
implied by the Trade Practices Act 1974
and State Territory legislation.
KAMBROOK guarantee.
KAMBROOK reserves the right to
replace or repair the appliance within
the warranty period.
For service, spare parts or product
information in Australia, please call
KAMBROOK on the customer Service
Line (free call) 1800 800 634.
Warranty does not apply to any defect,
deterioration, loss or injury or damage
occasioned by, or as a result of the misuse
or abuse, negligent handling or if the product
has not been used in accordance with the
instructions.The guarantee excludes
breakages and consumable items such as
kneading blades.
For service, spare parts or product
information in New Zealand, please
call KAMBROOK New Zealand, Mono
Place, Ellerslie,Auckland. Phone 0800 253
007, FAX 0800 263 001.
This warranty is void if there is evidence
of the product being tampered with by
unauthorised persons.
If claiming under this guarantee the product
must be returned to freight prepaid.
YOUR PURCHASE RECORD (Please complete)
Attach purchase receipt here.
DATE OF PURCHASE___________________________
MODEL NUMBER _____________________________
SERIAL NUMBER (If applicable) ___________________
Please don’t return purchase record
unless you are making a claim
PURCHASED FROM ___________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|