Jwin Telephone JT P433 User Manual

Vintage design big button Dual (FSK & DTMF)  
Caller ID telephone with LCD display  
Instruction Manual  
JT-P433  
Please read this manual carefully before operating and save it for future reference.  
Have a question? Please visit http://www.jWIN.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
USER SAFETY GUIDE  
Compliance (USA and Canada)  
This product complies with the standards in Part 68 of the FCC Rules in the USA  
and CS-03 in Canada.  
1. This product must be connected to the public switched telephone network  
through a modular telephone outlet or jack.  
2. Upon the request of the local telephone service provider, the user of this product  
must provide the following information:  
The “line” to which this telephone equipment will be connected (telephone  
number)  
The telephone equipment’s FCC registration number and ringer equivalence  
number. This information is printed on the back or bottom of the unit.  
3. If it is determined that this equipment is malfunctioning, the FCC requires that it  
not be used and that it must be unplugged from the modular outlet until the  
problem has been corrected.  
4. If the product causes harm to the telephone network, the telephone company  
may temporarily discontinue telephone service. Whenever possible, the  
telephone company will contact a customer prior to a service interruption. If  
advanced notice is not possible, the customer will be notifies as soon as possible.  
The customer will be given the opportunity to correct the problem.  
Download from Www.Somanuals.c-om2. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
Download from Www.Somanuals.c-om3. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
TABLE OF CONTENTS  
Getting Started  
General Features ……………………………………………………………………...  
In the Package ………………………………………………………………………...  
Location of Controls ………………………………………………………………..…  
Getting the Telephone Ready for Use ……………………………………………...  
Installing the Batteries ………………………………………………………………..  
6
6
7
8
8
Operational Instructions  
Basic Setup …………………………………………………………………………….  
9
Receiving Caller ID Information …………………………………………………….. 11  
Reviewing the Caller ID List …………………………………………………………. 11  
Erasing Data from the Caller ID List ………………………………………………... 11  
Calling a Number from the Caller ID List …………………………………………... 11  
Last Number Redial ………………………………………………………………….. 11  
Flash Function ………………………………………………………………………… 12  
Basic Instructions for Making a Phone Call ………………………………………... 12  
Basic Instructions for Receiving a Phone Call …………………………………….. 12  
Troubleshooting and Specifications …………………………………………….. 13  
Download from Www.Somanuals.c-om4. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
GETTING STARTED  
Thank you for purchasing the JT-P433 Vintage design big button Dual (FSK &  
DTMF) Caller ID telephone with LCD display. Please read and follow the instructions  
in this manual carefully to ensure that your product operates correctly.  
General Features  
Supports Dual caller ID systems (FSK and DTMF)  
Voice reporting functions for incoming calls  
Wide angle view LCD  
Extra large milk white backlight LCD  
Extra large dial pad  
Extra loud receiver volume up to 90dB  
Extra loud ringer volume up to 90dB  
Extra bright incoming call LED  
Supports 4 languages (English, Turkish, Spanish, and French)  
Incoming call memory (maximum 90 numbers)  
Built-in phonebook up to 25 numbers  
Outgoing call up to 17 numbers  
New incoming call indication  
16-digit telephone number and name display  
16 selectable ringer melodies  
4 level LCD contrast  
Full-performance speakerphone for hands-free operation  
Visual ringer LED  
Tone/Pulse selectable  
Ringer Volume Control (1/ 2/Off)  
Receiver Volume Control (1~4)  
Redial function  
Real time clock and date display  
In the Package  
Vintage design big button telephone with LCD display  
Telephone line cord  
AC adapter (UL/cUL listed)  
o
o
o
Input: 120V 60Hz,  
Output: DC 9V, 100mA  
Center Negative  
Instruction manual  
Warranty card  
Download from Www.Somanuals.c-om5. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
GETTING STARTED  
Location of Controls  
1
2
3
4
5
6
9
10  
11  
12  
13  
14  
7
8
15  
16  
1. RECEIVER  
2. NUMBER  
keypad  
5. DEL button  
6. AUTO / VIP  
button  
7. STORE / M1 /  
M2 buttons  
9. VOLUME button 13. FLASH button  
10. SPEAKER  
PHONE button  
11. UP/ DOWN  
button  
14. HOLD button  
3. LCD SCREEN  
15. speaker  
4. SET / BACK  
button  
8. SNOOZE button 12. REDIAL / P  
button  
16. DC 9V JACK  
Download from Www.Somanuals.c-om6. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
GETTING STARTED  
V10M10_IM_EN_01282008  
Getting the Telephone Ready for Use  
1. Choose a desired flat, level surface location for the unit.  
2. Plug one end of the coiled telephone cord into the jack on the handset, and the  
other into the matching jack on the unit’s base.  
3. Plug one end of the flat telephone cord into the jack in the rear of the unit’s base  
(marked TEL-LINE), and the other end into the wall jack which supplies  
telephone service.  
Installing the Batteries  
The JT-P433 requires three (3) AA batteries, which are used to operate the  
telephone, the LCD display, and to retain Caller ID data and any settings  
programmed into the phone. Using an optional 9V adapter (see Notes below) will  
increase the battery’s life span, requiring less frequent battery replacement.  
1. Remove the battery compartment cover at the bottom of the unit.  
2. Carefully install four (3) AA batteries by observing the polarity direction shown in  
the battery compartment.  
3. Replace the cover.  
Notes:  
Whether installing batteries for the first time or replacing them, do not mix old  
and new batteries, nor should alkaline, standard (zinc-carbon), or rechargeable  
(nickel-cadmium) batteries be used together.  
When not using the phone for a long period of time, remove the batteries to  
prevent possible leakage and corrosion. Keeping the phone powered by the  
optional AC adapter, discussed below, will preserve all data and settings in the  
phone’s memory.  
If neither the batteries nor an AC adapter are connected, the JT-P430 will still be  
able to place and receive calls, but the telephone, the ability to store Caller ID  
data, and the LCD display functions will not operate.  
When batteries are used without an AC adapter, they should be replaced when  
the display dims.  
When replacing the batteries without an AC adapter connected, it’s the best to  
pick up the handset before removing the batteries. Doing so prevents the loss of  
stored Caller ID data and programmed settings while the batteries are being  
replaced. If not done, it’s possible that all settings and data in the phone’s  
memory will be lost.  
Download from Www.Somanuals.c-om7. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Basic Setup  
Note: Please be sure the telephone lines are connected well and batteries or AC  
adapter are installed before starting setting. Press the SET/BACK button to enter the  
setting menu, use UP or DOWN buttons to select from the menu including Set  
Language, Set Local Area Code, Set Time/Date and LCD Contrast. Press the  
FLASH button to exit the setting manual.  
A. SET LANGUAGE  
-
-
-
When the LCD displays “SET LANGUAGE”, press the SET/BACK button  
to enter.  
Use the UP or DOWN buttons to select the desired language (English,  
French, Spanish, Turkish).  
Press the SET/BACK button to confirm.  
B. LCD CONTRAST  
-
-
-
When the LCD displays “LCD CONTRAST”, press the SET/BACK button  
to enter.  
Press the UP or DOWN buttons to select the desired contrast level  
from 1 to 4.  
Press the SET/BACK button to confirm.  
C. SET DATE/TIME  
-
When the LCD displays “SET DATE/TIME”, press the SET/BACK button  
to enter.  
-
-
-
Press the UP or DOWN buttons to set the present year.  
Press the SET/BACK button to confirm the year.  
Use the same method to set month ,day, hour and minute  
D. SET LOCAL AREA CODE  
-
When the LCD displays “LOCAL AREA CODE”, press the SET/BACK  
button to enter.  
-
-
-
Press the UP or DOWN buttons to select the first digit of area code.  
Press the SET/BACK button to confirm the first digit.  
Use the same method to set the rest of the digits  
E. SET LONG DISTANCE CODE  
-
When the LCD displays “LONG PREFIX”, press the SET/BACK button to  
enter  
-
-
Press UP or DOWN to select the code  
Press the SET/BACK button to confirm the code  
F. SET IP NUMBER (SSN=SPECIAL SERVICE NUMBER)  
Note: The Special Service Number (SSN) is a sequence of digits that can be  
stored in your telephone and used to gain access to certain features of a  
telephone network prior to dialing an actual phone number. Unless you are  
completely familiar with the use of an SSN sequence, it is best to skip this  
feature.  
-
-
-
-
When the LCD displays “SET SSN”, press the SET/BACK button to enter  
Press UP or DOWN to select the first digit  
Press the SET/BACK button to confirm the first digit  
Use the same method to set the rest of the digits  
Download from Www.Somanuals.c-om8. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Basic Setup-continued  
G. SET ALARM CLOCK  
-
-
When the LCD displays “ALARM”, press the SET/BACK button to enter  
The LCD will display “OFF” and “-1-“ (means the 1st group of alarm clock).  
Press UP or DOWN to select the alarm group. There are a total of  
three (3) groups to be selected.  
-
-
-
-
-
Press the SET/BACK button to enter the setting  
Press UP or DOWN to select “ONE TIME”, “P.D”(everyday) or “OFF”  
Press the SET/BACK button to confirm  
Press the SET/BACK button to enter hour setting  
Press UP or DOWN buttons to select the desired alarm hour from 1  
to 12 am or pm  
-
-
-
Press the SET/BACK button to confirm  
Use the same method to set the alarm minute  
Press the FLASH button to set the alarm time  
Notes:  
1. The alarm will keep around 50 seconds every time. Press any button  
(except the star & SNOOZE button) or pick the handset to stop the alarm.  
2. During alarm period, any incoming call will stop the alarm function  
3. During alarm period, press SNOOZE to delay the alarm time. It will alarm  
again after five (5) minutes. Press any button (except the star button and  
SNOOZE) or put the handset to stop the alarm function.  
H. SET RINGER MELODY  
-
When the LCD displays “RING MELODY”, press the SET/BACK button to  
enter  
-
The LCD will display “RING MELODY” and “-01-”, press UP or  
DOWN to select the desired melody from 01-16.  
-
Press the SET/BACK button to confirm  
I. SET VIP RING MELODY  
-
-
When the LCD displays “VIP RING MELODY”, press the SET/BACK  
button to enter  
The LCD will display “VIP RING MELODY” and “-01-”, press UP or  
DOWN to select the desired VIP melody from 01-16  
Press the SET/BACK button to confirm  
-
J. SET FLASH TIME  
-
-
-
When the LCD displays “FLASH TIME”, press the SET/BACK button to  
enter  
Press UP or DOWN to select the flash time among 100MS,  
120MS,180MS, 270MS, 300MS, 600MS and 1000MS  
Press the SET/BACK button to confirm  
K. SET PAUSE TIME  
-
-
-
When the LCD displays “PAUSE TIME”, press the SET/BACK button to  
enter  
Press UP or DOWN to select the pause time among 1S, 2S, 3S and  
4S. (S=Seconds)  
Press the SET/BACK button to confirm  
Download from Www.Somanuals.c-om9. -All Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Basic Setup-continued  
L. SET DIALING MODE  
-
-
-
When the LCD displays “DIAL MODE”, press the SET/BACK button to  
enter.  
Press UP or DOWN to select the desired dialing mode. ‘TONE’ for  
tone dialing and ‘PULSE’ for pulse dialing  
Press the SET/BACK button to confirm  
Note: Under the pulse dial state, press the Star button to change to tone dial.  
M. SET VOICE TARGET NUMBER  
The voice target number is very useful when you are not at home/office to pick  
the call. After setting the voice dialing number, the phone will announce “please  
call XXXXXX (the setting number)” after five (2 ) ringing sounds.  
-
When the LCD displays “TARGET NUMBER”, just press the desired  
number (at most 16 digits)  
-
Press the SET/BACK button to confirm  
N. SET VOICE REPORTING ON/OFF  
-
-
-
Under off-hook state, press the Star button for three (3) seconds to enter  
the setting.  
Press the Star button to choose “VOICE NUMBER/ON” or “VOICE  
NUMBER/OFF”  
If you select “VOICE NUMBER/ON”, the phone will announce the  
incoming number twice. Select “VOICE NUMBER/OFF” to disable the  
function of voice reporting  
O. SET CALL FORWARD TO VOICE MAIL  
-
-
-
Under off-hook state, press “” for three (3) seconds to enter the setting  
Press “” to choose “CALL FORWARD/ON” or “CALL FORWARD/OFF”  
If select “CALL FORWARD/ON” and there is any incoming call, the phone  
will announce the voice target number (please refer setting point M) three  
times after 2 ringing sounds.  
P. SET CALL FORWARD TO EXTENTION LINE  
-
Under off-hook state, press the SET/BACK button for 3 seconds, the LCD  
will display “OFF” and “- -“  
-
-
Press UP or DOWN to select “ON”  
Enter one or two digit(s) from 0-9, Press UP or DOWN to select  
desired number (Press the SET/BACK button to confirm the first digit and  
then set the second digit)  
Note: If you want to set “OFF” from “ON”, under off-hook state, press the  
SET/BACK button for 3 seconds and the LCD will display “ON” and “- -“. Then  
press UP or DOWN to select the “OFF”  
Q. MUSIC ON HOLD FUNCTION  
-
-
-
Under off hook state (Pick the phone or during speakerphone in use  
status), press [HOLD] to enter music on hold status  
The LCD will display “HOLD” and “-01-” , press UP or DOWN to  
select the music hold melody from 01-04.  
Press HOLD again to recover the conversation  
Note: During the incoming call, if press HOLD once, the ringing sound will be  
turn off immediately. However, it will resume the ringing sound in next  
incoming call.  
Download from Www.Somanuals.-co1m0. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Basic Setup-continued  
R. RINGER VOLUME CONTROL  
-
-
-
Under off- hook state, press VOLUME to enter the setting  
The LCD will display “RING VOLUME” and “-2-”(the volume level).  
Press VOLUME to select the ringer volume level.“1”is low level, “2”is high  
level and “OFF” is ringer off.  
Note: If you choose ringer off, you can still dial out, but cannot hear ringer  
sound of any incoming calls. (Ringer LED will still flash to remind you there is  
incoming call.) Don’t forget to set the ringer to ‘ON’ (i.e. select volume level ‘1’  
or ‘2’), otherwise, you cannot hear the ringer on next time  
S. HANDSET VOLUME CONTROL  
-
-
-
Pick the handset and press VOLUME to enter the setting  
The LCD will display “HANDSET VOLUME” and “-3-” (the volume level).  
Press VOLUME to select the handset volume level from 1-4. (‘1’ is the  
lowest volume and ‘4’ is the highest.)  
T. SPEAKER VOLUME CONTROL  
-
Under the speakerphone in use status, press VOLUME to enter the  
setting  
-
-
The LCD will display “SPEAKER VOLUME” and “-3-” (the volume level).  
Press VOLUME to select the speakerphone volume level from 1-4. (‘1’ is  
the lowest volume and ‘4’ is the highest.)  
U. KEYPAD SECURITY LOCK  
-
-
-
Under off-hook state, press “*#0000#” (‘0000’ is default as security code)  
to set as keypad unlock or all lock.  
For example, if press “*#0000#” once, the keypad will be locked. No any  
outgoing call is allowed. Press “*#0000#” again to unlock the keypad.  
If you want to change the security code, under off-hook state, press  
“*#xxxx*yyyy#” (xxxx means the old security code, yyyy means the new  
security code)  
Note: If you forget the old security code, then use ‘6666’ as old security code  
Download from Www.Somanuals.-co1m1. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Recieving Caller ID Information  
Note: You must make sure your Telephone Company offer caller ID service so that  
the caller ID function can be activated.  
A. Incoming Call Display  
When there is an incoming call, the LCD will display the number, area code, name,  
time and date of the call.  
B. Please note the following indicator:  
“UNAVAILABLE”  
The call is made through a telephone company, which does not offer Caller ID  
service or does not transfer calls by long distance net  
“BLOCKED CALL”  
Some areas allow the option for callers to prevent the telephone data from being  
displayed on others’ telephone. If you received such a call, “BLOCKED CALL” will be  
shown on LCD  
“Message Icon”  
If you apply message service to your telephone company, LCD will display Message  
icon of post box when there is a message left. When you read this message, the  
message icon will disappear.  
Reviewing the Caller ID List  
-
Press UP or DOWN to review the incoming calls (at most 80 calls)  
Erasing Data From the Caller ID List  
-
Under on-hook or off-hook state, press UP or DOWN to select the  
wanted number, press the DEL button twice to erase the number.  
Under on-hook or off-hook state, if press the DEL button continuously  
more than three seconds and the entire Caller ID list will be erased.  
-
Calling Back a Number from the Caller ID List  
-
Under on-hook state, press UP or DOWN to select the wanted  
number  
-
Press the SET/BACK button and the LCD will display “PICKUP OR ADJ”  
(if the incoming number is 10 digits) or “PICKUP PHONE” (if the incoming  
number is 7 or 11 digits)  
-
-
Press the SET/BACK button to adjust showing 7, 10 or 11 digits  
Pick the handset or press the SPEAKER button to dial out the number  
automatically.  
-
-
Under off-hook state, if area code was set, press UP or DOWN to  
select the desired number  
Press the SET/BACK button, if the displaying number is 10 digits, the  
number will be dialed out automatically with adding “1” as first digit. If the  
displaying number is 7 or 11 digits, the number will be dialed out  
automatically.  
Download from Www.Somanuals.-co1m2. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Phonebook Review  
-
-
-
-
Under on-hook or off-hook state, press the BOOK button to enter the  
phonebook review  
When the LCD displays “SEARCH”, press UP or DOWN to review the  
phonebook number or  
Enter the letter of the name by using keypad, the wanted telephone  
number will display on LCD, press UP or DOWN to review one by one  
Press [FLASH] to exit the phonebook review  
Phonebook Input  
-
-
-
-
-
Press [BOOK] twice continuously, the LCD will display “EDIT”  
Press UP or DOWN and the LCD will display “PLS INPUT NUMBER”.  
Input the desired directly by using keypad.  
Press the BOOK button to confirm  
Then the LCD will display “PLS INPUT NAME”, use the key pad to enter  
the name (at most 16 letters) and use the DEL button to correct (For  
example: enter “C”, just continuously press [2] key three times )  
Press the BOOK button to confirm  
Repeat the steps to input another name and number  
When “MEMEORY FULL” displays on the LCD, it means the phonebook  
memory is full, no more new name and number can be input  
Press the DEL button to exit the phonebook input  
-
-
-
-
Phonebook Delete or Edit  
-
-
-
When reviewing the phonebook record, press the DEL button twice to  
erase the record.  
When reviewing the phonebook record, press the BOOK button to enter  
edit  
The LCD will display “EDIT”, press UP or DOWN and the LCD will  
display “PLS INPUT NUMBER”.  
-
-
-
Input the desired directly by using keypad.  
Press the BOOK button to confirm  
Then the LCD will display “PLS INPUT NAME”, use the key pad to enter  
the name (at most 16 letters) and use the DEL button to correct (For  
example: enter “C”, just continuously press [2] key three times )  
Press the BOOK button to confirm  
-
Set Auto IP On/Off  
-
Under off-hook state, press UP for three (3) seconds to set IP On or Off.  
(IP number must be set in advance).  
-
For example, if the IP number is 234567 and the long distance code is 1,  
press UP for three seconds to set IP ‘On’ and the LCD will display  
“234567-1”  
-
Press UP for three seconds again to set IP ‘Off’  
Download from Www.Somanuals.-co1m3. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Dialing IP Number  
-
When the IP was set as ‘On’, pick the handset and if press the first digit is  
long distant code, then it will run by IP format automatically or  
Under off-hook state, when reviewing the incoming and outgoing call, if  
the first digit of displaying number is long distant code, press the  
SET/BACK button, then it will run by IP format after hook the phone once.  
Under on-hook state, when reviewing the incoming and outgoing call, if  
the first digit of displaying number is long distant code, press the  
SET/BACK button and it will run by IP format automatically.  
-
-
Storing 2 One-Touch Dialing Memories  
-
-
Under the on-hook state, press the STORE button.  
The LCD will display “PLS INPUT NUMBER”. Enter the desired number  
by using keypad  
-
Press M1 or M2.  
Storing 2 One-Touch Dialing Memories from Incoming Calls  
-
-
During the incoming call, press the STORE button.  
The LCD will display “PLS INPUT NUMBER”. Press M1 or M2 to store the  
incoming number.  
Dialing From One-Touch Memories  
-
-
Under off-hook state, press the desired one-touch button (M1/M2)  
Press the SET/BACK button and the number will be dialed out  
automatically.  
-
Under off-hook state, press the desired one-touch button (M1/M2) and the  
number will be dialed out automatically.  
Deleting a One-Touch Memory Number  
-
-
Under off-hook state, press M1/M2 and it will show the stored number.  
Press the DEL button twice to erase the number and the LCD will display  
“NO CODE”  
Storing 10 Two-Touch Dialing Memories  
-
-
Under the off-hook state, press the STORE button.  
The LCD will display “PLS INPUT NUMBER”. Enter the desired number  
by using keypad  
-
-
Press the STORE button again and the LCD display “INPUT ADDR”  
Press the desired two-touch location from 0-9.  
Storing 10 Two-Touch Memories from Incoming Calls  
-
-
-
During the incoming call, press the STORE button.  
The LCD will display “PLS INPUT NUMBER”. Press STORE button again  
Then the LCD will display “PLS INPUT ADDR”, press the desired two-  
touch location from 0-9  
Download from Www.Somanuals.-co1m4. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
Dialing from Two-Touch Memories  
-
-
-
-
-
Under off-hook state, press the AUTO/VIP button, the LCD will display  
“INPUT ADDR”  
Press the desired two-touch location from 0-9 and the LCD will display the  
number  
Press the SET/BACK button and the number will be dialed out  
automatically.  
Under on-hook state, press the AUTO/VIP button, the LCD will display  
“INPUT ADDR”  
Press the desired two-touch location from 0-9, the LCD will display the  
number and it will be dialed out automatically.  
Deleting a Two-Touch Memory Number  
-
-
-
Under off-hook state, press the RECALL/VIP button, the LCD will display  
“INPUT ADDR”  
Press the desired two-touch memory from 0-9 and the LCD will display the  
number  
Press the DEL button twice to erase the number and the LCD will display  
“NO CODE”  
Forwarding a Call to an Extension Line  
-
When the call forwarding to extension line was set as “ON”, under DTMF  
mode, if you want to transfer the call to the extension line, press “” and  
then press the extension number  
-
-
You will here the ‘beep’ sound and wait for the extension line to receive  
the call  
When the extension line is received successfully, you may have  
conference call with the extension line and the third party or just place  
back the handset to complete the call. The extension line and the third  
party can continue the conversation.  
Note:1. You must forward the call to extension line within one minute after  
picking the phone, otherwise, the forwarding function will be exit automatically.  
2. When entering the extension number, wait one second between the digits.  
3. When entering the extension number, if wait more than 10 seconds between  
the digits, the call forwarding will be cancelled automatically.  
VIP Function  
-
When reviewing the incoming call, press the AUTO/VIP button once to  
save this number as VIP.  
-
When there is an incoming call, the VIP ringer melody will indicate this is  
the caller from VIP.  
-
-
VIP cannot be erased from the caller Id list  
If you want to cancel the VIP of the number, press the AUTO/VIP button  
again.  
Download from Www.Somanuals.-co1m5. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
OPERATIONAL INSTRUCTIONS  
New Incoming Call Indicator  
Under on-hook or off-hook state, when there is new incoming call, the new call LED  
will be lighted for 10 seconds and the new call icon will display on LCD at the same  
time. The new call icon will disappear after the new call has been reviewed.  
Last Number Redial  
The last outgoing number can be redialed automatically just by pressing the REDIAL  
button under on-hook state. This is useful especially if the line is busy.  
Flash Function  
- When in an office equipped with PABX, this telephone makes it easy to transfer  
calls  
- Ask caller to wait and press the FLASH button once  
- Dial the extension number which caller intended  
- When the party answers, just hang up the handset  
- When the line is busy or nobody answers, press FLASH button again to re-connect  
with the caller  
Conversation Time Indication  
During the conversation with another party, the LCD will display the conversation  
time, until to stop the conversation, and put back the handset or turn off the  
[SPEAKER] button.  
IMPORTANT NOTE: To operate this unit, you must have “CALLER ID SERVICE”  
setup with your local telephone company. Some functions such as CALLER NAME  
INDICATION will only operate if such services are included in the user’s Caller I.D.  
program with the local telephone company.  
Basic Instructions for Making a Phone Call  
1. Remove the handset from base and listen for dial tone.  
2. Listen for a dial tone to indicate that the phone is connected.  
3. Dial the number you wish to call using the number pad.  
Basic Instructions for Receiving a Phone Call  
Telephone will ring to alert the user of an incoming call.  
1. Lift the handset, hold earpiece to your ear and speak into the mouthpiece.  
2. To hang up, return the handset to the base at the conclusion of call.  
Download from Www.Somanuals.-co1m6. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
TROUBLESHOOTING & SPECIFICATIONS  
Troubleshooting  
No Display on LCD Screen  
o
Brightness on display may be turned down.  
ƒ Increase brightness level.  
o
No batteries or batteries are improperly installed.  
ƒ If no batteries, install three (3) AA batteries as directed or  
ƒ Install optional AC Adapter  
ƒ Make sure batteries observe to polarities (+/-) as indicated inside the  
battery compartment.  
No Dial Tone when handset is picked up  
o
Phone may not be connected properly.  
ƒ Make sure the handset jack is connected to the base jack using the  
colied wire.  
ƒ Make sure the base jack (TEL-LINE) jack is connected to the wall  
telephone jack using the flat wire.  
o
Telephone service may be interrupted by the telephone company  
ƒ Contact your telephone company to check the status of your service.  
Static or interruptions during phone conversation  
o
Bad connection between phones  
ƒ Hang up and dial number again  
o
Harsh weather conditions and/or lightning  
ƒ Hang up and dial number when weather conditions improve  
Can only receive incoming calls and cannot make outgoing calls  
o
Telephone service may be limited or suspended by your telephone company  
ƒ Contact your telephone company to check the status of your service.  
Specifications  
Inputs & Outputs  
o
o
o
Telephone line jack  
Handset jack  
DC Power input jack  
Power Sources  
o
o
9V (AC/DC) Power Adapter  
4.5V DC Battery (AA x 3) (for backup)  
Download from Www.Somanuals.-co1m7. A-ll Manuals Search And Download.  
Vintage Design Telephone with Caller ID  
V10M10_IM_EN_01282008  
Download from Www.Somanuals.-co1m8. A-ll Manuals Search And Download.  
TEL: 516-626-7188  
FAX: 516-626-7105  
© 2008 jWIN Electronics Corp. All rights reserved. No portion of this printed material or product  
enclosed herewith including design, shape and graphics, may be reproduced or transmitted in  
any form without the expressed written consent of jWIN Electronics Corp. by any means,  
electronic or mechanical, including photocopying, recording, or by use of an information storage  
and retrieval system. Any unauthorized distribution or reproduction of this printed material or  
product, or any portion thereof, will be prosecuted to the fullest possible extent of the law.  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Freezer BA 139 PS User Manual
Intel Laptop M980NU User Manual
Invacare Oxygen Equipment CE0123 User Manual
Invacare Personal Lift 1150703 User Manual
John Lewis Range JLBICH601 User Manual
Kawai Musical Instrument CP115 User Manual
Kenwood Stereo System XD A950DV User Manual
Kicker Speaker DES12 User Manual
Kodak Scanner Digital Ice Technology User Manual
Kompernass Wok KH1099 04 08 V2 User Manual