Juke Box With CD/Radio
Instruction Manual
JK-333
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lighting flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
Download from Www.Somanuals.com. All Manuals Search And Download.
6A. An appliance and cart combination should be moved with care. Quick stops, ex-
cessive force, and uneven surfaces may cause the appliance and cart combina-
tion to overturn.
7. Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling
only as recommended by the manufacturer.
8. Ventilation – The appliance should be situated so that its location or position
does not interfere with its proper ventilation. For example, the appliance should
not be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings or placed in a built-in installation, such as a bookcase or
cabinet that may impede the flow of air through the ventilation openings.
9. Heat – The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers) that
produce heat.
10. Power Sources – The appliance should be connected to a power supply of the
type described in the operating instructions or as marked on the appliance.
11. Grounding or Polarization – Observe the precautions that should be taken so
that the grounding or polarization protective features of an appliance are not
defeated.
12. Power – Cord Protection – Power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
13. Protective Attachment Plug – The appliance is equipped with an attactment plug
that has overload protection. This is a safety feature. If replacement of the plug
is required, be sure the service technician uses a replacement plug specified by
the manufacturer that has the same overload protection as the original plug.
14A. Cleaning – The appliance should be cleaned only as recommended by the
manufacturer.
14B. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
15. Power Lines – An outdoor antenna should be located away from power lines.
16. Outdoor Antenna Grounding – If an outside antenna is connected to the receiver,
be sure the antenna system is grounded so as to provide some protection
against voltage surges and built up static charges. Section 801 of the National
Electrical Code. ANSI/NFPA NO. 70-1984, provides information with respect to
proper grounding of the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding electrodes, and
requirements for the grounding electrode. See Figure 73.1.
17. Nonuse Periods – The power cord of the appliance should be unplugged from
the outlet when left unused for a long period of time.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Object and Liquid Entry – Care should be taken so that objects do not fall and
liquids are not spilled into the unit through openings.
19. Damage Requiring Service – The appliance should be serviced by qualified
service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
E. The appliance has been dropped, or damaged.
20. Servicing – The user should not attempt to service the appliance beyond
instructions given in the operating instructions. All other servicing should be
referred to qualified service personnel.
POWER LINES
GROUND CLAMPS
SERVICE ENTRANCE
STANDOFF
INSULATORS
CONDUCTORS
b
MAST
ANTENNA
LEAD IN WIRE
SERVICE
ENTRANCE
EQUIPMENT
GROUND WIRE
GROUND CLAMPS
ANTENNA
DISCHARGE
UNIT
a.
a
c
TO EXTERNAL ANTENNA
TERMINALS OF PRODUCT
a.
a
GROUND WIRE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
GROUND CLAMPS
(e.g. ntenor water pipe)
c
OPTIONAL ANTENNA GROUNDING ELECTRODE
DRI/ENG FEET (2.44 m) INTO THE EARTH
IF REQUIRED BY LOCAL CODES SEE NEC
SECTION 810-21 (1)
BONDING JUMPER
FIGURE 73.1
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
INSTRUCTIONS CONTAINED IN ARTICLE 810-
“RADIO AND TELEVISION EQUIPMENT”
a. Use No. 10 AWG (5.3 mm2) copper, No. 8 AWG (8.4 mm2) aluminium, No. 17
AWG (1.0 mm2) copper-clad steel or bronze wire, or larger, as a ground wire.
b. Secure antenna lead-in and ground wire to house with stand-off insulators
spaced from 4 - 6 feet (1.22 - 1.83 m) apart.
c. Mount antenna discharge unit as close as possible to where lead-in enters
house.
d. Use jumper wire not smaller than No. 6 AWG (13.3 m 2) copper, or the
equivalent when a separate antenna-grounding electrode is used. See NEC
Section 810 - 21 (i).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF PARTS
2
3
1
12
11
13
14
19
15
16
18
17
6
7
8
4
5
9
10
1. Dial Display Door
2. Dial Display
3. Tuning Knob
4. Speaker
5. CD Door
6. AM/FM Band Switch
7. Function Switch
8. Volume Control
9. FM Antenna
10. Power Plug
11. Fast Forward Button
12. Power Indicator
13. FM Stereo Indicator
14. Stop Button
15. Fast Reverse Button
16. Repeat Button
17. Play/Pause Button
18. Program Button
19. Program Indicator
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SOURCE
Unwind the AC power cord at the back of the unit and connect it to a power outlet.
RADIO OPERATION
1. Switch the unit ON by turning the FUNCTION switch to the RADIO position.
2. Adjust the volume by turning the VOLUME control.
3. Select the desired waveband by adjusting the BAND selector to either the AM or
FM position.
4. Open the DIAL DISPLAY DOOR. Select the desired station on the DIAL DISPLAY
by rotating the TUNING KNOB.
5. Switch the unit OFF by turning the FUNCTION switch to the OFF position.
ANTENNA
For FM operation, the unit is provided with an antenna wire. Move the wire until the
reception is clear with no interference. Do not connect external FM antenna to an
outside antenna.
This device has a built-in Am antenna, rotate the unit for best Am reception.
CD OPERATION
PLAYBACK
1. Rotate the FUNCTION switch to CD position.
2. Press the Open Symbol " " on the door to open the disc door. Place a disc in the
tray with the labeled side facing out.
3. Close the door, the display will show "_ _" for a few seconds, then the total number
of tracks on the disc will be displayed.
4. Press the PLAY/PAUSE BUTTON to start playback.
5. Adjust the VOLUME CONTROL as desired.
6. To stop playback temporarily, press the PLAY/PAUSE BUTTON. The play mode
indicator will flash. Press the PLAY/PAUSE BUTTON again to resume playback.
7. To stop playback, press the STOP BUTTON and the play mode indicator will go off.
FAST FORWARD AND FAST REVERSE
1. Press the FAST FORWARD or FAST REVERSE BUTTON to select a desired track.
2. Press the PLAY/PAUSE BUTTON to start playback of the selected track.
SEARCH FORWARD AND REVERSE DURING PLAYBACK
1. Press the FAST FORWARD or FAST REVERSE BUTTON and keep it pressed to
search forward or backward for the desired point on the track.
2. Release the button at the desired point, playback will resume automatically.
REPEAT PLAYBACK
1. To select the single track repeat function, choose the track that you want to repeat,
then press PLAY/PAUSE BUTTON to play the track. Press the REPEAT BUTTON
once, to activate the single track repeat and the repeat indicator will flash.
2. To select the all tracks repeat function. Press the PLAY/PAUSE BUTTON to start
the track. Press the REPEAT BUTTON twice, to activate the all tracks repeat
function and the indicator will remain on.
3. To erase the repeat function, press again the REPEAT BUTTON until the indicator
turns off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMED PLAYBACK
1. In stop mode, press the PROGRAM BUTTON "0" (flashing) wil show on the display
and the program indicator will flash.
2. Press the FAST FORWARD or REVERSE BUTTON to make track selection.
3. Press the PROG BUTTON again to store the selected track number.
4. Repeat steps 2 and 3 above to program other tracks.
5. Press the PLAY/PAUSE BUTTON to start programmed playback and the program
indicator will on.
6. To erase the programmed, press the PROG BUTTON and press the STOP
BUTTON once or open the CD door.
NOTE: Maximum of 19 tracks can be programmed to play in any order.
SPECIFICATIONS:
Power Source
Speaker Impedance
Output Power
:
:
:
120V/60Hz
3½" 8 ohm
1.5W x 2 R.M.S.
CD
Frequency Response
Sampling Frequency
:
:
100 - 16,000 Hz
44.1 KHz
Tape
Frequency Response
Tape Speed
:
:
100 - 8,000 Hz
4.75 cm/sec.
TROUBLE SHOOTING GUIDE
The unit does not operate
•
•
Is the AC power cord connected to a power outlet and fully inserted?
Is the unit turned on? Rotate the FUNCTION switch from the OFF position to turn
on the unit.
No radio
•
Is the FUNCTION switch in the correct position?
Turn FUNCTION switch to Radio.
Adjust the VOLUME knob.
Rotate the TUNING knob to find a radio station.
•
•
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MUST RETURN BY MAIL
IMPORTANT! PLEASE READ:
In order to validate this warranty, fill out this portion in its entirety and return to jWIN within 10 DAYS of
purchase. Please print clearly. jWIN will not be liable if we are unable to process your warranty due to
illegibility, failure to complete the form properly, or failure to return the form as specified.
Model Number:
Owner's Name:
Address:
Serial No.
Date of Purchase:
City:
State:
Zip Code:
Store Name:
Store Address:
City:
State:
Zip Code:
Cut along this line
1
YEAR PARTS
/
90 DAYS LABOR LIMITED WARRANTY
This warranty applies to customers in the U.S. (mainland) only. Please refer to our website for international
serivice information.
jWIN Electronics Corp. (“jWIN”) warrants this product to the original purchaser ONLY, to be free from
defects in materials and workmanship under normal use during the period specified under this warranty
effective from the date of original purchase. jWIN agrees, at our option, to replace or repair your product
with
a
new or reconditioned product without any charge. This warranty, of course, does not cover cosmetic
damage, cabinets, cabinet parts, knobs, stylus, antennas, handles, batteries, plugs, line cords, tapes and
accessories, or damage due to line power surges, connection to improper voltage supply or settings, misuse,
mishandling, acts of God, or attempted repair by an unauthorized service agent, or any product whose serial
number has been removed, altered, replaced, defaced, or rendered illegible.
A
minimum $25.00 fee will be charged for any repair service beyond 90 Days from the date of original
purchase. To obtain factory service, the original purchaser MUST present proof of purchase and send the unit
pre-paid to the address below. Also, $10.00 money order made payable to jWIN Electronics Corp. must be
a
included to cover return shipping charges.
jWIN Customer Service, 51-41 59th Place, Woodside, N.Y.11377
There are no express warranties except as listed above. REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. jWIN SHALL NOT BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A
PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
jWIN Electronics Corp.
51-41, 59th Place
Woodside, N.Y. 11377
Attn: Customer Service
Download from Www.Somanuals.com. All Manuals Search And Download.
|