GB Operator’s Manual
115 02 33-26
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Symbols
2
2
3
3
4
5
5
7
7
8
Slip clutch
11
11
11
Important! Read before using chain saw
Contents
Electronic overload protection 2000W
Cutting equipment
EC declaration of conformity
Technical specifications
Chain saw parts
Chain and guide bar lubrication
- Chain oil
12
12
12
12
- Filling chain oil
- Checking automatic
chain lubrication system
- Checking chain wear
Safe use
Starting and stopping
Daily inspection and maintenance
Kickback prevention
12
13
13
14
Filing chain
Limbing
Chain brake with kickback guard
- Kickback guard inspection
9
9
9
9
Crosscutting
Felling operations
- Danger zone
14
15
15
15
15
- Manual chain brake function check
- Inertia chain brake function check
- Felling direction
- Clearing branches/Line of retreat
- Felling
Mounting guide bar and adjusting chain
Chain catcher
10
11
11
Right hand guard
EC DECLARATION OF CONFORMITY
Husqvarna Norge AS, N-1708 Sarpsborg, Norway hereby declares that the following chain saws:
Jonsered CS 2117EL and Jonsered CS 2121EL, with serial numbers starting at 54000001 and onwards,
- are manufactured in compliance with EC Directive 98/37/EC (Machinery), EC Directive 73/23/EEC including amendments
(Low Voltage Directive), EC Directive 89/336/EEC including amendments (Electromagnetic Compatibility Directive), and in
accordance with annex V of Directive 2000/14/EC (Noise Emission in the environment by equipment for use outdoors)
- are manufactured in compliance with the following harmonized standards: EN 50144-1, EN 50144-2-13, IEC 60745-1
and IEC 60745-2-13.
Notified body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has:
- carried out the EC type examination in accordance with the machinery Directive (98/37/EC) Article 8(2)(c)
- issued EC type examination certificates No. 404/04/1038 - Jonsered CS 2117 EL
and 404/04/1037 - Jonsered CS 2121 EL pursuant to machinery Directive 98/37/EC, Annex IV (4)
The chain saw submitted is identical to the samples submitted for EC type examination.
The measured and guaranteed sound power levels in accordance with Directive 2000/14/EC are set forth under Technical Data
in the User’s Manual.
Sarpsborg, 1th of October 2005
--
Jan Hansen, President
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Motor
Rated voltage
1700
220-240
2000
230
2000
50
VAC
W
Rated output
1700
Frequency
Hz
50/60
Slip clutch
Yes
Yes
Electronic start control
Electronic speed control
Electronic overload protection
-
-
-
Yes
Yes
Yes
Weight
Without guide bar and chain
kg
kg
4,4
5,1
4,4
5,1
With 14” guide bar and chain
Chain lubrication
Oil tank volume
litres
litres
0.1
0.1
Oil consumption approx.
Oil pump
0.1/20 min.
auto
0.1/20 min.
auto
Noise levels
Equivalent noise intensity at operator’s ear,
according to international standards
dB(A)
95
95
Noise emissions
Sound power, measured
LW dB(A)
104
106
104
106
Sound power, guaranteed
LWA dB(A)
Vibration
Front handle
Rear handle
m/s2
m/s2
4.4
5,4
4.4
5,4
Chain/guide bar
Recommended bar length
inches/cm
inches/cm
inches/cm
inches/cm
inches/cm
inches/cm
m/sec. (drive)
m/sec. (drive)
inches
12/30
12/30
14/35
14/35
16/40
16/40
Effective cutting length
12/30
12/30
14/35
14/35
16/40
16/40
Chain speed, unloaded
Chain speed, rated output
Chain pitch
14,5 (6 tooth)
12,5 (6 tooth)
3/8
15,2 (6 tooth)
12,2 (6 tooth)
3/8
Gauge
inches/mm
12”/14”/16”
.050/1.3
45/52/56
.050/1.3
45/52/56
Number of drive links
inch
inch/mm
inch/mm
inch/mm
inch/cm/dl
(
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN SAW PARTS
1. Rear handle
2. Power trigger lockout
3. Front handle
11. Chain
12. Guide bar
4. Serial No. plate
5. Chain tensioner
6. Chain oil reservoir
7. Chain oil level
8. Ventilation slots
9. Power cable
18. Chain catcher - deflects chain in case
chain breaks or derails
19. Guide bar nut
13. Chain brake release button
14. Kickback guard
15. Chain drive cover
20. Nose sprocket
16. Right hand guard - protects right hand
in case chain breaks or derails
17. Drive sprocket
21. Scabbard
22. Combination tool
23. Operator’s manual
10. Power trigger
- concealed by chain drive cover
SAFE USE
CAUTION!
Never operate a chain saw with one hand only. Doing so may lead to i serious injury
to operator, helpers or bystanders. An electric chain saw is designed for operation
with both hands.
DANGER!
Use of accessories not conforming to the recommendations outlined in the
Operating Instructions could lead to injury.
• Dress safely. Avoid jewellery and loose-fitting clothing,
which may be caught in moving parts. Approved safety
mitts and sturdy footwear which gives a good footing are
recommended (also for helpers).
Wear: - Approved face mask or safety goggles
- Approved hearing protection
- Approved helmet
- Approved safety boots with protective rein-
forcement, steel toecap and non-slip soles
- Clothing which is snug without hampering
movement
- Approved gloves with protective reinforcement
Always keep a first-aid kit on hand!
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
See to it that others keep their distance as long as the
chain is in motion. Keep onlookers, children and animals
away from the work area. Do not let inexperienced persons
handle the chainsaw or power cable.
•
Ensure that you can move and stand safely at all times.
Watch out for roots, stones, branches, holes, mounds
and so forth when moving around. Be particularly careful
when working on slopes. Work with the trunk to your right,
keeping the log between you and the guide bar. Always grip
your chain saw with both hands, holding it as close to your
body as possible for best control. Wherever possible, let
the log take the weight of the chain saw. Always keep the
log between you and the guide bar when moving forward.
Keep work area clear and well-lighted. Do not operate chain
saw under wet or humid conditions, around water or in rain
or snow. Ingress of moisture into the motor can cause short-
circuiting.
Show caution, care and common sense. Do not operate
the chain saw when you are tired or under the influence
of alcohol or drugs which may affect vision, judgement or
physical control. Keep all body parts well away from the
chain as long as the motor is running. Always ensure that
the chain is not touching anything before starting the chain
saw.
•
Do not bear down hard when cutting. With the chain
properly sharpened, light pressure is sufficient. Forcing the
saw at the end of a cut can make you lose control when you
break through.
•
•
Secure short logs before sawing.
Show particular care when cutting small branches, and
avoid sawing bushes or many small branches at once.
Small branches can get caught in the chain with a violent
jerk and cause serious personal injury.
•
•
Be on your guard against electric shock. Avoid touching
metal objects imbedded in or in electrical contact with the
ground.
Do not abuse power cables. Never lift or carry the chain
saw by the power cable, and never disconnect the power
by jerking on the cable. Keep cable away from water, oil
and sharp objects. Avoid crushing cable in or against
doors, fences, or other metal objects which can conduct
electricity.
•
We recommend limiting tree diameter to guide bar length so
that the NOTCH and FELLING CUT may be done with single
cuts. (See «Technical Specifications» for recommended
guide bar lengths for your chain saw model).
•
Inspect the chain saw and power cable before use. Do not
use a chain saw with a damaged cable. Get it repaired by
qualified service personnel. Keep handles clean, dry and
free of grease and oil.
•
•
See to it that all tools are removed from the chain saw
before connecting the power.
Ensure that the extension cord is in good condition and
approved for outdoor use. It must be of sufficient dimension
for the chain saw’s rated power. See section «IMPORTANT!
READ BEFORE USING CHAIN SAW» on page 1.
•
The chain will keep rotating a short while after releaseing
the power trigger (slowness).
•
When carrying the chain saw, stop the motor, keep your
finger AWAY from the power trigger and turn the saw with
the guide bar to the rear and pointing away from your
body.
•
•
Disconnect power supply before servicing chain saw.
Your chain saw complies with all relevant safety standards.
Repairs should be performed only by qualified service
personnel using only original parts.
•
•
Connect chain saw to a power supply equipped with a
current-operated earth-fault protection device.
•
Examine saw closely for damaged parts before use to avoid
malfunctions and to ensure safe and efficient operation.
Verify that all moving parts are fitted and adjusted correctly.
Except for the maintenance described in this operator’s
manual, damaged parts must be replaced at an authorized
service centre. Defective power triggers are to be replaced
by authorized service personnel. Do not operate the saw if
the power trigger does not work properly.
Double-insulated! Your electric chain saw is double-
insulated for added protection against electric shock. A
double-insulated electric tool is designed with two separate
«layers» of electrical insulation or one layer of insulation
of double thickness between the operator and the tool’s
conducting parts. Double-insulated tools do not use earthed
mains connections and may therefore be connected to any
normal 220-240 VAC outlet. Observe the same precautions
required with all electric tools. Double insulation gives
added protection only against defective insulation.
•
Store the chain saw in a safe, dry place out of the reach of
children, with the power disconnected and the guide bar
scabbard in place.
•
Use chain saw only on wood. Do not attempt to cut metal, plastic,
masonry or any non-wood building materials. Do not use the
guide bar to push away branches, roots or other objects.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
CAUTION!
•
Make certain at all times that your footing is
secure and that the chain touches nothing
but the wood you are cutting.
•
Keep bystanders away from your work area.
Starting
•
•
•
Grip the front handle firmly with your left hand.
Grip the rear handle firmly with your right hand.
Press and hold the power trigger lockout button with the inside of your
hand and squeeze the power trigger with your index finger.
Stopping
Stop the saw by releasing the power trigger. If the saw does not stop,
trip the chain brake and disconnect the power cable.
DAILY INSPECTION AND MAINTENANCE
CAUTION!
Always disconnect the power before cleaning or performing maintenance.
Here are a few general instructions for maintaining your hand-
saw. If you are in doubt on any of these points, contact your
service dealer.
1. Inspect power cable and plug for defects.
A damaged power cable or plug must be replaced.
2. Clean ventilation openings and keep them open.
3. Check automatic chain lubrication.
4. Turn guide bar over at regular intervals to distribute the
wear on both sides. Check to see that the oil passage is
clear. Clean the guide bar groove.
5. Check chain tension, sharpen the cutters and ensure that
chain turns easily.
6. Check drive sprocket for abnormal wear, replacing it if
necessary.
7. Remove any burrs from the edges of the guide bar
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KICKBACK PREVENTION
DANGER!
Kickbacks occur suddenly and without warning. A kickback may be violent enough to throw a
chainsaw back at the user. A running chain can inflict severe and even fatal injury. It is imperative
for users to be familiar with the causes of kickbacks in order to exercise the proper care and use
working techniques to prevent kickback.
CAUTION!
Improperly sharpened cutters or the wrong chain and guide bar combination will
increase the risk of kickback. See «Technical Specifications» on page 3.
CAUTION!
Do not let the chain come in contact with the ground or any objects. Chain link and wire fencing
materials present a particular kickback hazard.
Observe all safety rules in order to avoid kickbacks and other
accidents which may cause injury.
•
A kickback is a sudden reaction in which a chain saw is
thrown back as a result from contact with the upper part of
the bar nose known as the kickback danger zone.
•
The direction of a kickback is always in the same plane as
the guide bar. The most common reaction is that the guide
bar and saw are thrown up and back towards the operator.
The saw can be thrown in other directions, depending on
the position of the saw at the moment of kickback.
Basic rules
•
Take extreme care when cutting with the top chain (on the
underside of a log). The force of the chain action pushes the
saw backwards, and if the operator does not maintain firm
control, the kickback danger zone may move far enough
back into the kerf to produce a kickback. Cutting with the
bottom chain (on the top side of the log) pulls the saw for-
ward. This presses the power head firmly against the tree,
providing a steady support and giving the operator added
control over the saw and consequently over the kickback
danger zone.
•
Knowing the cause and nature of a kickback helps reduce
or eliminate the element of surprise. Surprise increases the
danger of an accident. Most kickbacks are small, but some
are violent, and all are lightning-fast.
•
Always grip the chain saw firmly with thumb and fingers
wrapped around the handles, right hand on the rear handle
and left hand on the front handle. All users, whether right or
left-handed, must use this grip, which will reduce the effect
of a kickback and help keep the saw under control.
Do not let go of the chain saw handles!
•
Most accidents caused by kickbacks take place in con-
nection with limbing. Make certain your footing is secure
and that there are no objects nearby which may trip you
or make you lose your balance. If you are not careful, the
kickback danger zone could make contact with a branch,
a nearby tree or some other object which could cause a
kickback.
•
Follow the maintenance and sharpening instructions for the
chain and guide bar. When replacing chains and guide bars,
use only combinations recommended by us. See «Technical
Specifications».
•
•
The smaller the bar nose radius, the smaller the kickback
danger zone and thus
•
•
Never use a chain saw to cut above shoulder height, and
do not cut with the guide bar nose. Never operate a chain
saw while holding it with only one hand!
the kickback tendency.
By using low-kickback
cutting equipment and
keeping the cutters
properly sharpened, the
strength of a kickback
can be greatly reduced.
Maintain full speed while cutting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN BRAKE WITH KICKBACK GUARD
•
The chain brake may be activated manually or by the force
of inertia depending on the strength of the kickback and
the position of the saw in relation to the object which made
contact with the kickback danger zone.
Your chain saw is equipped with a chain brake designed to
stop the chain instantaneously in the event of a kickback.
A chain brake can reduce the risk of accident, but only the
operator can prevent accidents from happening. Be extremely
careful when operating a chain saw and do not allow the kick-
back danger zone to make contact with anything.
- If the kickback is sufficiently violent and the left hand
is too far from the kickback guard, the chain brake is
activated by the INERTIA of the chain brake against the
force of the kickback.
•
The chain brake (A) is activated either manually (with the left
hand) or by the force of inertia (the inertia of the kickback
guard resisting the motion of the saw from the force of the
kickback). However it is activated, the kickback protection
mechanism works in the opposite direction to the force of
the kickback. The saw incorporates a slip clutch which pro-
tects the saw against overload. If the chain stops while the
motor is running, the saw is overloaded. Ease up on the
cutting pressure until the chain starts running again. If the
saw jams in the tree, stop the saw immediately and free it.
- In the event of smaller kickbacks or when the left hand
is near the kickback guard, the chain brake is activated
manually with the left hand.
•
When the chain saw is turned on its side and the operator
is holding the side of the front handle, the kickback guard
will not strike the left hand in the event of a kickback and
will thus not activate the chain brake. In a situation of this
type, inertia is the only thing that can activate the chain
brake, but like manual activation, it will not work in every
situation.
Kickback guard inspection
•
The chain brake is also activated when the kickback guard
(B) is pushed forward. This releases a springloaded mecha-
nism which jerks the brake band tightly around the brake
drum.
•
Inspect kickback guard for visible defects, such as cracks.
•
Move kickback guard back and forth to ensure that it moves
freely without being loose.
Manual chain brake function check
•
Check chain brake daily or every time the saw is used.
Holding the running saw firmly with the left hand on the
front handle and the right hand on the rear handle, twist
your left wrist, pushing the kickback guard to activate the
chain brake without letting go of the front handle. The chain
should stop instantaneously. If the chain brake does not
perform as required, have it serviced by authorized per-
sonnel.
•
•
The purpose of the kickback guard is not only to activate
the chain brake. Its other important function is to reduce
the danger of contact with the chain in the event that the
operator loses his grip on the front handle.
Inertia chain brake function check
Use the chain brake as a «parking brake» when carrying
the chain saw around or putting it down for short periods!
Besides automatic activation in the event of a kickback, the
chain brake may also be activated manually and must be
activated in the event of any inadvertent contact with a ro-
tating chain.
•
Hold the running saw level with the guide bar approximately
45 cm above a stump or other solid wooden object.
Release the power trigger.
•
Release the front handle, letting
the chain saw pivot in your
right hand as the guide bar falls
down and strikes the stump.
The brake should activate when
the bar nose hits the stump.
•
•
An activated chain brake is released by pulling the kickback
guard back towards the front handle.
As pointed out on page 7, a kickback can be extremely
violent and lightning-fast. Most kickbacks are small and do
not activate the chain brake. When this happens, it is im-
portant to maintain a firm grip on the saw and not let go.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING GUIDE BAR AND ADJUSTING CHAIN
CAUTION!
Always disconnect power before performing cleaning or maintenance work.
CAUTION!
A loose chain can jump out of its groove during operation and cause serious
or even fatal injury.
6. Replace the chain drive cover and screw
the mounting nut hand tight.
1. Pull kickback guard back against the front handle
to ensure that the chain brake is not applied.
7. Tension the chain by screwing the
tensioning screw clockwise using the
screwdriver tip on the combination
tool.
2. Screw out the guide bar nut and remove
the chain drive cover.
8. Tighten chain firmly but not so hard that it does not turn easily
by hand force. Push the button to release the chain brake. To
avoid contact between your hands and the chain, use gloves
to turn the chain.
8
2
3. Fit the chain around guide bar nose with
the top cutters facing forwards.
9. Tighten the mounting nut with the combination tool while hold-
ing the tip of the guide bar up.
4. Holding the chain over the guide bar nose, position the
back end of the guide bar against the drive sprocket at a
45° angle to the power head. Pass the free end of the chain
around the drive sprocket, swing the guide bar into place
over the mounting bolt and against the power head, and
guide the chain into the guide bar groove.
The tension of a new chain must be checked frequently until it
is broken in. Continue to check the tension at regular intervals
to ensure good performance and a long service life.
•
•
Wear causes a chain to become looser with use. Regular
tensioning is important to compensate for this wear.
5. Seat the guide bar tensioner pin in its hole in the guide bar.
Check the chain tension at least every time you refill the chain
oil reservoir.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN CATCHER
The chain catcher is designed to catch a chain which breaks or jumps out of its groove.
This problem will generally be avoided, however, if the chain is tensioned properly (see
chapter on «Mounting guide bar and adjusting chain» page 9) and the chain and guide
bar properly maintained.
Ensure that the CHAIN CATCHER is undamaged.
RIGHT HAND GUARD
The right hand guard protects the right hand in the event that the chain breaks or
jumps out of its groove, as well as keeping twigs and branches from interfering with
your grip on the handle.
Ensure that the RIGHT HAND GUARD is undamaged.
SLIP CLUTCH
Your chain saw features a slip clutch which protects it from overload.
The slip clutch may require cleaning after long periods of operation.
Contact your nearest service dealer in the event of malfunction.
ELECTRONIC OVERLOAD PROTECTION 2000W
The 2000W electric chain saw is provided with electronic overload protection.
•
•
•
When the overload protection trips, the saw stops.
Release the power trigger. Ensure that the chain is not stuck.
Squeeze the power trigger.
CUTTING EQUIPMENT
This section explains how correct maintenance and use of the
right cutting equipment:
•
Ensure that the cutter teeth are always
correctly sharpened! Follow our
instructions and use the recommended
filing guide. A chain which is damaged or
improperly maintained increases the risk
of accident.
•
•
•
•
Reduces kickback tendencies
Reduces the frequency of chain derailing and breakage
Achieves maximum cutting effect
•
•
Maintain the correct depth-gauge height.
Worn depth gauges increase the risk of
kickback.
Increases the service life of the chain
Keep chain properly tensioned!
A loose chain derails more easily and
accelerates wear on guide bar, chain
and drive sprocket.
The five basic rules
•
Use only the recommended cutting equipment!
See «Technical Specifications» on page 3.
•
Ensure that the automatic oiling system
works and that the cutting equipment is
properly maintained.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN AND GUIDE BAR LUBRICATION
CAUTION!
Inadequate lubrication can lead to cutting equipment failure and serious or fatal
personal injury.
Chain oil
•
•
A full reservoir is sufficient for 20 minutes of steady use.
•
The chain and bar are lubricated by an automatic oiling
system. We recommend using only chain saw oil, which is
formulated for good adhesion and flow characteristics in hot
or cold weather. Nonetheless, it is important to use the vis-
cosity appropriate to the season. Oil thickens in subfreezing
temperatures and can overload the oil pump and cause
parts to fail.
If the lubrication system does not seem to be working, and
the following steps do not help, take your saw to a service
dealer.
-
Check the guide bar’s oil passage
and clean if necessary.
•
As a manufacturer of chain saws, we have developed an
ideal chain oil which, being based on vegetable oils, is
completely biodegradable. We recommend our oil for the
sake of your chain and guidebar and for the sake of the
environment.
-
Check guide bar groove and
clean if necessary.
•
•
•
Where chain oil is not available, EP 90 gear oil may be used.
If you need help choosing chain oil, contact your service dealer.
Never use old motor oil! Used motor oil contains impurities
which may be harmful to oil pump, guide bar and chain.
-
Ensure that the nose sprocket
turns easily and is not clogged.
Clean and grease if necessary.
Filling chain oil
•
All our chain saw models feature automatic chain lubrication.
Checking chain wear
•
Inspect chain every day for:
-
Visible cracks in rivets or links
Checking automatic chain lubrication system
-
-
-
-
Stiffness
•
Start the chain saw and point the guide bar towards a fixed,
light-coloured object at a distance of approximately 20 cm.
After running the saw for a minute, a streak of oil spatter
should be clearly visible on the light surface.
Abnormal wear in rivets or links
Min. 3 mm (1/8”) horizontal cutter length
Any deviation on any of these points indicates a worn
chain which must be discarded
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FILING CHAIN
See «Technical Specifications» for the details which apply to
General instructions regarding cutters
your chain. It is very difficult to file a chain saw correctly with-
out the proper aids. We recommend the use of a file guide to
ensure maximum cutting efficiency with the least tendency to
kickback.
•
Never cut wood using a dull chain. Having to press hard is a
sure sign of a dull chain, as are very small chips. A very dull
chain will produce sawdust rather than chips.
Filing cutters
To file cutters correctly, a ROUND FILE
and a FILE GUIDE are required. Look
under «Technical Specifications» for
the correct file diameter and file guide
for your saw and chain.
•
•
A sharp chain will produce large chips, and the saw will
feed itself through the wood.
The part of the chain that saws is
called the CUTTING LINK, which
consists of a CUTTER (A) and
DEPTH GAUGE (B). The difference
in height between them determines
the depth of the cut.
•
File only with the chain
properly tensioned. A loose
chain wiggles, making it
difficult to file.
•
•
•
Always file from the inside of each
cutter towards the outside. Lift
the file on the return stroke.
•
When filing a saw, pay close attention to:
TOP-PLATE ANGLE
CUTTING ANGLE
HORIZONTAL FILE ANGLE
FILE DIAMETER
File the cutters on one side first.
Then turn the saw around and file
the cutters on the other side.
Make certain that all cutters are of
equal length. When the horizontal
length is down to 3 mm (1/8”), the
chain is worn out and must be dis-
carded.
FILE DEPTH
CAUTION!
Improperly filed cutters heighten
kickback tendencies!
LIMBING
CAUTION!
Most kickback accidents take place when limbing. Pay very close attention to the
kickback danger zone when cutting limbs under tension!
All the principles which apply to crosscutting also apply when cutting thick branches.
Cut complicated branches in several stages.
Ensure that your footing is secure at all times, whether moving about or
standing in one place. Always work with the log to your right. For best control,
hold the chain saw as close to your body as possible.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CROSSCUTTING
•
Cutting a log supported at one end. The log is more than
CAUTION!
likely to splinter if cut straight through from the top down.
If the chain becomes stuck in the
kerf, STOP THE SAW!
Do not attempt to jerk the saw free.
You could be harmed by the chain
if the saw suddenly comes loose.
Lever the saw free instead.
- Make an initial cut from below (approx. 1/3 of the
diameter)
•
Cutting a log on the ground. There is little danger of the
saw jamming or the log splintering, but it is difficult to avoid
running the saw into the ground when breaking through at
the end of the cut.
- Finish the cut from above.
Saw straight through the log. Be careful at the end of the
cut to avoid contact with the ground. Keep the saw running
at full speed, but be prepared for the breakthrough.
•
Cutting a log supported at both ends. The saw is more than
likely to jam in the kerf if cut straight through from above.
- Make an initial cut from the top (approx. 1/3 of the
diameter).
- If it is possible to turn the log, stop cutting 2/3
of the way through the log.
- Finish the cut from below.
- Turn the log and cut the remaining section from above.
FELLING OPERATIONS
CAUTION!
Felling a tree is a job which calls for experience. Do not attempt to fell trees if you are
inexperienced. DO NOT CARRY OUT ANY OPERATIONS FOR WHICH YOU DO NOT
FEEL QUALIFIED!
CAUTION!
Beginning chain saw operators should gain experience cutting logs on a sawhorse or
similar arrangement.
CAUTION!
We advise operators without sufficient experience against felling trees with trunk
diameters exceeding their guide bar length.
14
´®z+R7@¶6T¨
´®z+R7@¶6T¨
Download from Www.Somanuals.com. All Manuals Search And Download.
Danger zone
Notch depth should be around 1/4 of the
diameter of the tree and the angle should
be around 45°.
A
danger zone surrounds the tree to
a
distance of
2 1/2 times the height of the tree. See to it that no one is
standing within this zone while you are felling the tree.
Felling direction
The line defined by the inside angle of the
notch must be precisely horizontal and
at a precise right angle to the direction
of fall.
When felling a tree, one always aims to place it where neither
objects nor difficult terrain will hamper limbing and cutting.
Unobstructed movement and secure footing are essential.
It is also important to avoid lodging the tree against another
tree. A lodged tree is extremely dangerous.
Felling cut
The felling cut is done from the opposite
side of the tree and must also be
horizontal. Stand with the tree to your left
and cut with the bottom of the guide bar
(pulling chain).
After determining where you want the tree to fall, you must
also consider the likely unaided direction of fall. This is
affected by the straightness and lean of the tree, wind direc-
tion, concentration of branches and any snow that may weigh
the tree down.
After assessing all these factors, you may find you have no
choice but to fell the tree in its natural direction of fall because
your preferred direction of fall is likely to fail.
Place the FELLING CUT approximately
3-5 cm (1 1/2 - 2”) above the BOTTOM
NOTCH CUT.
Another important factor affecting your personal safety, though
it has no bearing on the direction of fall, is the presence of any
dead branches which could fall while you are felling the tree.
Cut at full motor speed, feeding the saw
slowly into the tree. Watch out for tree
movement opposite to the intended direc-
tion of fall. Insert a WEDGE or FELLING
BAR in the FELLING CUT as soon as the
depth of the cut permits.
Clearing branches/Line of retreat
Remove any branches from around
Planned Direction of fall
the base of the tree which may in-
terfere with your work. It is safest to
Danger zone
work from the top down and to keep
the tree trunk between you and the
When complete, the FELLING CUT must
be parallel to the notch and leave a
strip of HINGE WOOD at least 1/10 the
diameter of the tree.
Retreat
Retreat
running chain. Never cut branches
above shoulder height. Clear under-
growth around the tree and identify
Danger zone
your line of retreat or escape, taking note of any obstructions
(stones, branches, holes, etc.).Your line of retreat should be at
an angle, around 135° behind the direction of fall.
The HINGE WOOD acts as a hinge,
steering the direction of the falling tree.
Felling
If the HINGE WOOD is too small or has
been sawn through, or if the
notch and the felling cut are
mismatched, the tree is no
longer under control.
Three cuts are made to fell a tree. The «TOP NOTCH CUT»
and the «BOTTOM» or «HORIZONTAL NOTCH CUT» forms
the «NOTCH», which determines the direction in which the
tree will fall. The final cut is the «FELLING CUT», which allows
the tree to topple over.
Notch
As the felling cut approaches the notch,
the tree should start falling, either by
itself or with the help of a WEDGE or
FELLING BAR.
To form the NOTCH, start with the TOP
NOTCH CUT. Using the bottom of the
guide bar (pulling chain), make a 45°
downward angled cut at right angles to
the intended direction of fall.
Next do the BOTTOM NOTCH CUT,
ensuring that it meets the bottom of the
TOP NOTCH CUT precisely.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Trøskenveien 36
P.O.B. 10
N - 1708 Sarpsborg
Norway
115 02 33-26
´®z+R7@¶6T¨
´®z+R7@¶6T¨
2006W11
Download from Www.Somanuals.com. All Manuals Search And Download.
|