Operator′s manual
Please read the operator’s manual carefully and
make sure you understand the instructions
before using the machine.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
Note the following before starting:
KEY TO SYMBOLS
Please read the operator’s manual carefully.
Symbols .......................................................................
CONTENTS
2
WARNING! Long-term exposure to noise can
result in permanent hearing impairment. So
always use approved hearing protection.
Contents ......................................................................
Note the following before starting: ................................
INTRODUCTION
3
3
!
!
Dear Customer, ............................................................
WHAT IS WHAT?
4
5
WARNING! Under no circumstances may the
design of the machine be modified without
the permission of the manufacturer. Always
use genuine accessories. Non-authorized
modifications and/or accessories can result
in serious personal injury or the death of the
operator or others.
What is what? ..............................................................
GENERAL SAFETY PRECAUTIONS
Important ......................................................................
Personal protective equipment .....................................
Machine′s safety equipment ........................................
Cutting equipment ........................................................
ASSEMBLY
6
6
7
9
WARNING! A clearing saw, brushcutter or
trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
Fitting the main body ................................................... 11
Fitting the handlebar .................................................... 11
Connecting throttle cable and stop switch wires .......... 11
Assembling the cutting equipment ............................... 12
Adjusting the harness and clearing saw ...................... 13
Standard harness ........................................................ 13
FUEL HANDLING
!
Fuel safety ................................................................... 14
Fuel .............................................................................. 14
Fuelling ........................................................................ 15
STARTING AND STOPPING
Check before starting ................................................... 16
Starting and stopping ................................................... 16
WORKING TECHNIQUES
General working instructions ....................................... 18
MAINTENANCE
Carburettor ................................................................... 21
Muffler .......................................................................... 21
Cooling system ............................................................ 21
Air filter ......................................................................... 21
Bevel gear .................................................................... 22
Spark plug .................................................................... 22
Maintenance schedule ................................................. 23
TECHNICAL DATA
Technical data .............................................................. 24
EC-declaration of conformity ........................................ 25
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Jonsered product!
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to
come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be
necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service
workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s
manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value
of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator′s manual.
Good luck on using your Jonsered machine!
Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance
of products without prior notice.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
1
2
3
7
10
9
11
12
16
8
14 15
4
5
6
32
20
13
17
25
26
18
21
30
19
27
28
22
23
31
29
24
5
4
What is what?
1
2
3
4
5
6
7
8
9
Trimmer head
17 Air purge
Bevel gear
18 Air filter cover
19 Fuel tank
Grease filler cap, bevel gear
Cord cutter
20 Starter handle
21 Transport guard
22 Socket spanner
23 Spanner
Cutting attachment guard
Guard extension
Shaft
Handle adjustment
Throttle control
24 Locking pin
25 Locking nut
26 Support flange
27 Support cup
28 Blade
10 Stop switch
11 Start throttle button
12 Throttle lockout
13 Suspension ring
14 Clutch cover
29 Drive disc
30 Harness
15 Choke control
16 Cylinder cover
31 Operator′s manual
32 Handlebar
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Important
WARNING! Listen out for warning signals or
shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
!
IMPORTANT!
The machine is only designed for trimming grass.
HELMET
The only accessories you can operate with this engine unit
are the cutting attachments we recommend in the chapter
on Technical data.
A protective helmet where there is a risk of falling objects
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect your
vision, your judgement or your co-ordination.
HEARING PROTECTION
Wear personal protective equipment. See instructions
under the heading ”Personal protective equipment”.
Wear hearing protection that provides adequate noise
reduction.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual.Some maintenance and service measures must be
carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
EYE PROTECTION
Always wear approved eye protection. If you use a visor then
you must also wear approved protective goggles. Approved
protective goggles must comply with standard ANSI Z87.1 in
the USA or EN 166 in EU countries.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition lead
are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working. When
several operators are working in the same area the safety
distance should be at least twice the tree height and no less
than 15 metres.
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
WARNING! This machine produces an
electromagnetic field during operation.This
field may under some circumstances
interfere with active or passive medical
implants.To reduce the risk of serious or
fatal injury, we recommend persons with
medical implants to consult their physician
and the medical implant manufacturer
before operating this machine.
!
BOOTS
Wear boots with steel toe-caps and non-slip sole.
WARNING! Running an engine in a confined
or badly ventilated area can result in death
due to asphyxiation or carbon monoxide
poisoning.
!
CLOTHING
Personal protective equipment
Wear clothes made of a strong fabric and avoid loose clothing
that can catch on twigs and branches. Always wear heavy,
long pants. Do not wear jewellery, shorts sandals or go
barefoot. Secure hair so it is above shoulder level.
IMPORTANT!
A clearing saw, brushcutter or trimmer can be dangerous if
used incorrectly or carelessly, and can cause serious or
fatal injury to the operator or others. It is extremely
important that you read and understand the contents of this
operator’s manual.
FIRST AID KIT
Always have a first aid kit nearby.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen. Ask
your dealer for help in choosing the right equipment.
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Press the throttle lockout and make sure it returns to its
original position when you release it.
Machine′s safety equipment
This section describes the machine′s safety equipment, its
purpose, and how checks and maintenance should be carried
out to ensure that it operates correctly. See the ”What is
what?” section to locate where this equipment is positioned
on your machine.
The life span of the machine can be reduced and the risk of
accidents can increase if machine maintenance is not carried
out correctly and if service and/or repairs are not carried out
professionally. If you need further information please contact
your nearest service workshop.
Check that the throttle control and throttle lockout move freely
and that the return springs work properly.
IMPORTANT! All servicing and repair work on the machine
requires special training. This is especially true of the
machine′s safety equipment.If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee the
availability of professional repairs and service. If the retailer
who sells your machine is not a servicing dealer, ask him for
the address of your nearest service agent.
See instructions under the heading Start. Start the machine
and apply full throttle. Release the throttle and check that the
cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position
then the carburettor idle setting must be checked. See
instructions under the heading Maintenance.
WARNING! Never use a machine with faulty
safety equipment.The machine’s safety
equipment must be checked and maintained
as described in this section. If your machine
fails any of these checks contact your
service agent to get it repaired.
!
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock (A)
(i.e.when you grasp the handle) it releases the throttle control
(B). When you release the handle the throttle control and the
throttle lockout both move back to their original positions.This
movement is controlled by two independent return springs.
This arrangement means that the throttle control is
automatically locked at the idle setting.
Stop switch
Use the stop switch to switch off the engine.
A
B
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
Cutting attachment guard
This guard is intended to prevent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting attachment.
Check that the guard is undamaged and not cracked.Replace
the guard if it has been exposed to impact or is cracked.
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
Quick release
There is an easily accessible, quick release fitted at the front
as a safety precaution in case the engine catches fire, or in
any other situation that requires you to free yourself from the
machine and harness. See instructions under the heading
Adjusting the harness and clearing saw.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
Vibration damping system
Your machine is equipped with a vibration damping system
that is designed to minimize vibration and make operation
easier.
Check that the harness straps are correctly positioned. Once
the harness and machine have been adjusted, check that the
harness quick release works correctly.
Muffler
Using incorrectly wound cord or a blunt or incorrect cutting
attachment (wrong type or incorrectly filed, see instructions
under the heading Filing the blade) increases the level of
vibration.
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
The machine′s vibration damping system reduces the transfer
of vibration between the engine unit/cutting equipment and
the machine′s handle unit.
Regularly check the vibration damping units for cracks or
deformation.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with a
spark arrestor mesh. Check whether the muffler on your
machine is fitted with this kind of mesh.
Check that the vibration damping element is undamaged and
securely attached.
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve damage
in people who have impaired circulation.
!
Contact your doctor if you experience
symptoms of overexposure to vibration.
Such symptoms include numbness, loss of
feeling, tingling, pricking, pain, loss of
strength, changes in skin colour or
condition.These symptoms normally appear
in the fingers, hands or wrists.The risk
increases at low temperatures.
For mufflers it is very important that you follow the instructions
on checking, maintaining and servicing your machine.
Never use a machine that has a faulty muffler.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Regularly check that the muffler is securely attached to the
machine.
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
•
•
•
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
If the muffler on your machine is fitted with a spark arrestor
mesh this must be cleaned regularly. A blocked mesh will
cause the engine to overheat and may lead to serious
damage.
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to check
the correct way to load the cord and the correct cord
diameter.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
!
Keep the teeth of the blade correctly sharpened! Follow our
recommendations. Also refer to the instructions on the
blade packaging.
WARNING! Always stop the engine before
doing any work on the cutting attachment.
This continues to rotate even after the
throttle has been released. Ensure that the
cutting attachment has stopped completely
and disconnect the HT lead from the spark
plug before you start to work on it.
WARNING! The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of a
damaged muffler.
!
!
WARNING! Bear in mind that:The exhaust
fumes from the engine are hot and may
contain sparks which can start a fire. Never
start the machine indoors or near
combustible material!
!
WARNING! Using an incorrect cutting
attachment or an incorrectly sharpened
blade increases the risk of blade thrust.
!
Locking nut
Cutting equipment
A locking nut is used to secure some types of cutting
attachment.
Grass blades and grass cutters are intended for cutting
coarse grass.
A trimmer head is intended for trimming grass.
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove it,
undo the nut in the same direction as the cutting attachment
rotates. (CAUTION! The nut has a left-hand thread.) Tighten
the nut using the socket spanner.
General rules
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Keep the teeth of the blade correctly sharpened! Follow our
Trimmer head
instructions and use the recommended file gauge. An
incorrectly sharpened or damaged blade increases the risk of
accidents.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and evenly
around the drum, otherwise the machine will generate
harmful vibration.
•
Only use the recommended trimmer heads and trimmer
cords.These have been tested by the manufacturer to suit
a particular engine size.This is especially important when
a fully automatic trimmer head is used. Only use the
recommended cutting attachment. See the chapter on
Technical data.
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
•
•
Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using a
cord the engine must throw out the cord radially from the
trimmer head and overcome the resistance of the grass
being cleared.
Sharpening grass cutters and grass
blades
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
•
•
See the cutting attachment packaging for correct
sharpening instructions. Sharpen blades and cutters
using a single-cut flat file.
•
•
Make sure that the cutter on the trimmer guard is intact.
This is used to cut the cord to the correct length.
To increase the life of the cord it can be soaked in water
for a couple of days.This will make the line tougher so that
it lasts longer.
Sharpen all edges equally to maintain the balance of the
blade.
WARNING! Always discard a blade that is
bent, twisted, cracked, broken or damaged
in any other way. Never attempt to straighten
a twisted blade so that it can be reused. Only
use original blades of the specified type.
!
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting the main body
Connecting throttle cable and stop
switch wires
Connect the engine (A) to the tube (B) with four screws (C).
1
Remove the air filter cover.
2
Insert the throttle cable (A) through the carburettor bracket
(B), then screw the cable adjuster sleeve (C) into the
carburettor bracket fully.
A
C
B
Fitting the handlebar
•
Fit the handlebar in the handlebar clamp on the shaft
using six screws.
3
Position the slotted fitting (D) on the carburettor so the
recessed hole (E) for the cable lug (F) is away from the
cable adjuster sleeve.
4
Rotate the carburettor throttle cam and slip the throttle
cable through the slot in the slotted fitting, making sure the
cable lug drops into the recessed hole.
5
6
Operate the throttle trigger a few times to make sure that
it works correctly.
•
Attach the cabling to the shaft with two cabling holders.
Adjust the cable adjuster sleeve so the stop on the
carburettor throttle cam just contacts the throttle stop and
the cable position keep 1-2 mm play between the cable
lug and the slotted fitting when the throttle trigger is fully
depressed.
1-2mm
•
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness.
7
8
When the throttle cable is adjusted correctly, tighten the
locking nut (G).
Plug the stop switch wires (H) into the matching
connectors from the engine. Note that wire polarity is not
important.
H
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
9
Lap and fix the stop switch wires and connectors with
clamp (I).
Fitting a blade guard, grass blade and
grass cutter
I
•
Fit the guard (A) to the gear housing using the support
plate (M) and two screws (L).
B
L
C
M
10 Refit the air filter cover.
A
Assembling the cutting equipment
•
•
Fit the drive disc (B) on the output shaft.
WARNING! When fitting the cutting
attachment it is extremely important that the
raised section on the drive disc/support
flange engages correctly in the centre hole
of the cutting attachment. If the cutting
attachment is fitted incorrectly it can result
in serious and/or fatal personal injury.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
!
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D), support cup (E) and support flange
(F) on the output shaft.
G
E
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
F
!
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
D
IMPORTANT! If a saw blade or grass blade are to be used
the machine must be equipped with the correct handlebar,
blade guard and harness.
B
C
Fitting the cord cutter and guard extension
to the trimmer guard
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
guard as possible. To tighten the nut, turn the spanner in
the opposite direction to the direction of rotation (Caution!
left-hand thread).
•
Attach the cord cutter to the guard extension with screw
and washer as shown.
•
Fit the guard extension to the trimmer guard as shown.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting other guards and cutting
attachments
Standard harness
Quick release
At the front is an easily accessible, quick release. Use this if
the engine catches fire or in any other emergency situation
that requires you to free yourself from the machine and
harness.
•
Fit the guard (A) to the gear housing using the support
plate (M) and two screws (L).
B
L
C
M
A
•
•
Fit the drive disc (B) on the output shaft.
Spreading the load on your shoulders
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
A well-adjusted harness and machine makes work much
easier. Adjust the harness for the best working position.
Tension the side straps so that the weight is evenly distributed
across both shoulders.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Screw on the trimmer head (H) in the opposite direction to
the direction of rotation.
•
To dismantle, follow the instructions in the reverse order.
Correct height
Adjust the shoulder strap so that the cutting attachment is
parallel to the ground.
Adjusting the harness and clearing
saw
WARNING! When using a clearing saw it
must always be hooked securely to the
harness. Otherwise you will be unable to
control the clearing saw safely and this can
result in injury to yourself or others. Never
use a harness with a defective quick release.
!
Correct balance
Let the cutting attachment rest lightly on the ground. Adjust
the position of the suspension ring to balance the clearing
saw correctly.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Petrol
Fuel safety
Never start the machine:
1
2
If you have spilt fuel on it. Wipe off the spillage and allow
remaining fuel to evaporate.
NB! Always use a quality petrol/oil mixture at least 90 octane
(RON). If your machine is equipped with a catalytic converter
(see chapter on Technical data) always use a good quality
unleaded petrol/oil mixture. Leaded petrol will destroy the
catalytic converter.
If you have spilt fuel on yourself or your clothes, change
your clothes.Wash any part of your body that has come in
contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for leaks
from the fuel cap and fuel lines.
Use low-emission petrol, also known as alkylate petrol, if it is
available.
Transport and storage
•
Store and transport the machine and fuel so that there is
no risk of any leakage or fumes coming into contact with
sparks or naked flames, for example, from electrical
machinery, electric motors, electrical relays/switches or
boilers.
•
•
The lowest octane recommended is 90 (RON). If you run
the engine on a lower octane grade than 90 so-called
knocking can occur. This gives rise to a high engine
temperature, which can result in serious engine damage.
•
•
When storing and transporting fuel always use approved
containers intended for this purpose.
When storing the machine for long periods the fuel tank
must be emptied. Contact your local petrol station to find
out where to dispose of excess fuel.
When working at continuous high revs a higher octane
rating is recommended.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
Two-stroke oil
The transport guard must always be fitted to the cutting
attachment when the machine is being transported or in
storage.
•
For best results and performance use JONSERED two-
stroke engine oil, which is specially formulated for our air-
cooled two-stroke engines.
•
Secure the machine during transport.
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion and
inhaling fumes.
•
•
Never use oil intended for four-stroke engines.
!
A poor oil quality and/or too high oil/fuel ratio may
jeopardise function and decrease the life time of catalytic
converters.
Fuel
•
Mixing ratio
NB! The machine is equipped with a two-stroke engine and
must always been run using a mixture of petrol and two-stroke
oil. It is important to accurately measure the amount of oil to
be mixed to ensure that the correct mixture is obtained.When
mixing small amounts of fuel, even small inaccuracies can
drastically affect the ratio of the mixture.
1:50 (2%) with JONSERED two-stroke oil.
1:33 (3%) with oils class JASO FB or ISO EGB formulated
for air-cooled, two-stroke engines.
Two-stroke oil, litre
Petrol, litre
2% (1:50)
0,10
3% (1:33)
0,15
WARNING! Fuel and fuel fumes are highly
inflammable and can cause serious injury
when inhaled or allowed to come in contact
with the skin. For this reason observe
caution when handling fuel and make sure
there is adequate ventilation.
5
!
10
15
20
0,20
0,30
0,30
0,45
0,40
0,60
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing
Fuelling
•
Always mix the petrol and oil in a clean container intended
for fuel.
•
Always start by filling half the amount of the petrol to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of petrol.
WARNING!Taking the following precautions,
will lessen the risk of fire:
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
!
Do not smoke or place hot objects near fuel.
Always shut off the engine before refuelling.
Always stop the engine and let it cool for a
few minutes before refuelling.
When refuelling, open the fuel cap slowly so
that any excess pressure is released gently.
Tighten the fuel cap carefully after refuelling.
Always move the machine away from the
refuelling area before starting.
•
•
Do not mix more than one month’s supply of fuel at a time.
•
•
Always use a fuel container with an anti-spill valve.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Clean the area around the fuel cap. Contamination in the
tank can cause operating problems.
•
Ensure that the fuel is well mixed by shaking the container
before filling the tank.
WARNING! The catalytic converter muffler
gets very hot during and after use.This also
applies during idling. Be aware of the fire
hazard, especially when working near
flammable substances and/or vapours.
!
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Check before starting
Starting and stopping
•
Check the blade to ensure that no cracks have formed at
the bottom of the teeth or by the centre hole. The most
common reason why cracks are formed is that sharp
corners have been formed at the bottom of the teeth while
sharpening or that the blade has been used with dull
teeth. Discard a blade if cracks are found.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
!
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the cutting
attachment cannot come into contact with
any object.
Make sure no unauthorised persons are in
the working area, otherwise there is a risk of
serious personal injury.The safety distance
is 15 metres.
•
Check that the support flange is not cracked due to fatigue
or due to being tightened too much. Discard the support
flange if it is cracked.
Starting
•
•
Ensure the locking nut has not lost its captive force. The
nut lock should have a locking force of at least 1.5 Nm.
The tightening torque of the locking nut should be 35-50
Nm.
Cold engine
Ignition: Set the stop switch to the start position.
Check that the blade guard is not damaged or cracked.
Replace the blade guard if it is exposed to impact or is
cracked.
Primer bulb: Press the air purge repeatedly until fuel begins
to fill the bulb. The bulb need not be completely filled.
•
Check that the trimmer head and trimmer guard are not
damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or are
cracked.
Choke: Set the choke control in the choke position.
•
•
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged before
you start the machine.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Warm engine
Use the same starting procedure as for a cold engine but
without setting the choke control in the choke position.
WARNING! When the engine is started with
the choke in either the choke or start throttle
positions the cutting attachment will start to
rotate immediately.
!
Hold the body of the machine on the ground using your left
hand (CAUTION! Not with your foot!). Grip the starter handle,
slowly pull out the cord with your right hand until you feel
some resistance (the starter pawls grip), now quickly and
powerfully pull the cord.Never twist the starter cord around
your hand.
Repeat pulling the cord until the engine starts. When the
engine starts, return choke control to run position.
CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully extended.
This can damage the machine.
CAUTION! Do not put any part of your body in marked area.
Contact can result in burns to the skin, or electrical shock if
the spark plug cap has been damaged. Always use gloves.
Do not use a machine with damaged spark plug cap.
Stopping
Stop the engine by switching off the ignition.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
6
Always hold the machine with both hands. Hold the
machine on the right side of your body.
General working instructions
IMPORTANT!
This section describes the basic safety precautions for
working with clearing saws and trimmers.
If you encounter a situation where you are uncertain how to
proceed you should ask an expert. Contact your dealer or
your service workshop.
Avoid all usage which you consider to be beyond your
capability.
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
7
8
Keep the cutting attachment below waist level.
Switch off the engine before moving to another area. Fit
the transport guard before carrying or transporting the
equipment any distance.
Basic safety rules
9
Never put the machine down with the engine running
unless you have it in clear sight.
1
•
Look around you:
WARNING! Neither the operator of the
machine nor anyone else may attempt to
remove the cut material while the engine is
running or the cutting equipment is rotating,
as this can result in serious injury.
To ensure that people, animals or other things cannot
affect your control of the machine.
!
•
To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects that
are thrown out by the cutting attachment.
Stop the engine and cutting equipment
before you remove material that has wound
around the blade shaft as otherwise there is
a risk of injury.The bevel gear can get hot
during use and may remain so for a while
afterwards.You could get burnt if you touch
it.
•
NB! Do not use the machine unless you are able to call
for help in the event of an accident.
2
Inspect the working area. Remove all loose objects, such
as stones, broken glass, nails, steel wire, string, etc. that
could be thrown out or become wrapped around the
cutting attachment.
3
4
Do not use the machine in bad weather, such as dense
fog, heavy rain, strong wind, intense cold, etc. Working in
bad weather is tiring and often brings added risks, such as
icy ground, unpredictable felling direction, etc.
WARNING! Watch out for thrown objects.
Always wear approved eye protection. Never
lean over the cutting attachment guard.
Stones, rubbish, etc. can be thrown up into
the eyes causing blindness or serious injury.
!
Make sure you can move and stand safely.Check the area
around you for possible obstacles (roots, rocks, branches,
ditches, etc.) in case you have to move suddenly. Take
great care when working on sloping ground.
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be kept outside the safety zone of 15
m. Stop the machine immediately if anyone
approaches. Never swing the machine
around without first checking behind you to
make sure no-one is within the safety zone.
Basic working techniques
Always slow the engine to idle speed after each working
operation. Long periods at full throttle without any load on the
engine can lead to serious engine damage.
5
Keep a good balance and a firm foothold.
WARNING! Sometimes branches or grass
get caught between the guard and cutting
attachment. Always stop the engine before
cleaning.
!
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Grass trimming with a trimmer head
WARNING! Machines fitted with saw blades
or grass blades can be thrown violently to
the side when the blade comes into contact
with a fixed object.This is called blade
thrust. A blade thrust can be violent enough
to cause the machine and/or operator to be
propelled in any direction, and possibly lose
control of the machine. Blade thrust can
occur without warning if the machine snags,
stalls or binds. Blade thrust is more likely to
occur in areas where it is difficult to see the
material being cut.
!
Trimming
•
Hold the trimmer head just above the ground at an angle.
It is the end of the cord that does the work. Let the cord
work at its own pace. Never press the cord into the area
to be cut.
Avoid cutting with the area of the blade
between the 12 o'clock and 3 o'clock
positions. Because of the speed of rotation
of the blade, blade thrust can occur if you
attempt to cut thick stems with this area of
the blade.
•
•
The cord can easily remove grass and weeds up against
walls, fences, trees and borders, however it can also
damage sensitive bark on trees and bushes, and damage
fence posts.
Grass clearing using a grass blade
Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
Clearing
•
Grass blades and grass cutters must not be used on
woody stems.
•
The clearing technique removes all unwanted vegetation.
Keep the trimmer head just above the ground and tilt it.Let
the end of the cord strike the ground around trees, posts,
statues and the like. CAUTION! This technique increases
the wear on the cord.
•
•
A grass blade is used for all types of tall or coarse grass.
The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left is the
clearing stroke and the movement from left-to-right is the
return stroke. Let the left-hand side of the blade (between
8 and 12 o’clock) do the cutting.
•
•
The cord wears quicker and must be fed forward more
often when working against stones, brick, concrete, metal
fences, etc., than when coming into contact with trees and
wooden fences.
When trimming and clearing you should use less than full
throttle so that the cord lasts longer and to reduce the
wear on the trimmer head.
•
•
If the blade is angled to the left when clearing grass, the
grass will collect in a line, which makes it easier to collect,
e.g. by raking.
Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly
again.
Cutting
•
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel
to the ground when cutting. Avoid pressing the trimmer
head against the ground as this can ruin the lawn and
damage the tool.
•
•
Let the support cup rest lightly against the ground. It is
used to protect the blade from hitting the ground.
Reduce the risk of material wrapping around the blade by
following these instructions:
1
2
Always work at full throttle.
Avoid the previously cut material during the return
stroke.
•
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting. Constant
contact of this type can cause damage and wear to the
trimmer head.
•
Stop the engine, unclip the harness and place the
machine on the ground before you start to collect the cut
material.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Sweeping
•
The fan effect of the rotating cord can be used for quick
and easy clearing up. Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
•
When cutting and sweeping you should use full throttle to
obtain the best results.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
blocked, this can be a sign that the performance of the
Carburettor
catalytic converter is impaired. Contact your dealer to inspect
the muffler. A blocked mesh will cause the machine to
overheat and result in damage to the cylinder and piston.
Adjusting the idle speed (T)
Check that the air filter is clean. When the idle speed is
correct, the cutting attachment should not rotate. If
adjustment is required, close (turn clockwise) the idle
adjustment screw T, with the engine running, until the cutting
attachment starts to rotate. Open (turn anticlockwise) the
screw until the cutting attachment stops. The idle speed is
correctly set when the engine runs smoothly in all positions,
and there is a clear margin to the speed at which the cutting
attachment starts to rotate.
CAUTION! Never use a machine with a defective muffler.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
!
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
3
4
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
Muffler
2
1
The cooling system consists of:
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether your
machine is fitted with a catalytic converter.
1
2
3
4
Air intake on the starter.
Fins on the flywheel.
The muffler is designed to reduce the noise level and to direct
the exhaust gases away from the operator. The exhaust
gases are hot and can contain sparks, which may cause fire
if directed against dry and combustible material.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Air filter
The air filter must be regularly cleaned to remove dust and dirt
in order to avoid:
•
•
•
•
Carburettor malfunctions
Starting problems
Loss of engine power
Some mufflers are equipped with a special spark arrestor
mesh. If your machine has this type of muffler, you should
clean the mesh at least once a week.This is best done with a
wire brush.On mufflers without a catalytic converter the mesh
should be cleaned weekly, or replaced if necessary. On
mufflers fitted with a catalytic converter the mesh should be
checked, and if necessary cleaned, monthly. If the mesh is
damaged it should be replaced. If the mesh is frequently
Unnecessary wear to engine parts.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
•
Excessive fuel consumption.
Bevel gear
The bevel gear is filled with the right amount of grease at the
factory. However, before using the machine you should check
that the bevel gear is filled 3/4 full with grease. Use
JONSERED special grease.
The grease in the bevel gear does not normally need to be
changed except if repairs are carried out.
Clean the filter every 25 hours, or more regularly if conditions
are exceptionally dusty.
Cleaning the air filter
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Ensure that the filter is dry before
refitting it.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
Spark plug
If the machine is used in dusty conditions the air filter should
be soaked in oil.See instructions under the heading Oiling the
air filter.
The spark plug condition is influenced by:
•
•
Incorrect carburettor adjustment.
Oiling the air filter
An incorrect fuel mixture (too much or incorrect type of
oil).
•
A dirty air filter.
Always use special filter oil. Filter oil contains a solvent to
make it spread evenly through the filter.You should therefore
avoid skin contact.
These factors cause deposits on the spark plug electrodes,
which may result in operating problems and starting
difficulties.
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour off
the excess before fitting the filter to the machine. Never use
common engine oil. This would drain through the filter quite
quickly and collect in the bottom.
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0,6-0,7 mm. The spark plug should
be replaced after about a month in operation or earlier if
necessary.
CAUTION! Always use the recommended spark plug type!
Use of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More
extensive work must be carried out by an authorized service workshop.
Daily
Weekly
Monthly
Maintenance
maintenance maintenance maintenance
Clean the outside of the machine.
X
X
Check that the harness is not damaged.
Make sure the throttle trigger lock and the throttle function correctly from a
safety point of view.
X
Check that the handle and handlebar are undamaged and secured correctly.
Check that the stop switch works correctly.
X
X
X
X
Check that the cutting attachment does not rotate at idle.
Clean the air filter. Replace if necessary.
Check that the guard is undamaged and not cracked. Replace the guard if it has
been exposed to impact or is cracked.
X
X
Check that the blade is correctly centred, is sharp, and is not cracked. An off-
centre blade will cause vibration that could result in damage to the machine.
Check that the trimmer head is undamaged and not cracked. Replace the
trimmer head if necessary.
X
X
X
Check that the locking nut of the cutting equipment is tighten correctly.
Check that the transport guard for the blade is intact and that it can be secured
correctly.
Check that nuts and screws are tight.
X
X
X
X
Check that there are no fuel leaks from the engine, tank or fuel lines.
Check the starter and starter cord.
Check that the vibration damping elements are not damaged.
Clean the outside of the spark plug. Remove it and check the electrode gap.
Adjust the gap to 0.5 mm or replace the spark plug. Check that the spark plug
is fitted with a suppressor.
X
Clean the machine’s cooling system.
X
X
X
X
Clean or replace the spark arrestor mesh on the muffler (only applies to mufflers
without a catalytic converter).
Clean the outside of the carburettor and the space around it.
Check that the bevel gear is filled three-quarters full with lubricant. Fill if
necessary using special grease.
Check the fuel filter from contamination and the fuel hose from cracks or other
defects. Replace if necessary.
X
X
X
X
X
Check all cables and connections.
Check the clutch, clutch springs and the clutch drum for wear. Replace if
necessary by an autorized service workshop.
Replace the spark plug. Check that the spark plug is fitted with a suppressor.
Check and clean the spark arrestor mesh on the muffler (only applies to mufflers
fitted with a catalytic converter).
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
BC2043
BC2053
Engine
3
Cylinder displacement, cm
Cylinder bore, mm
Stroke, mm
41,5
40
49,9
43,9
33
33
Idle speed, rpm
2600
10400
8060
1,77/7500
No
2600
10400
8060
1,91/7500
No
Recommended max. speed, rpm
Speed of output shaft, rpm
Max. engine output, acc. to ISO 8893, kW/ rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
No
No
Spark plug
NGK BPMR 6Y NGK BPMR 6Y
Electrode gap, mm
0,6-0,7
0,6-0,7
Fuel and lubrication system
Fuel tank capacity, litre
1,0
1,0
Weight
Weight without fuel, cutting attachment and guard, kg
Noise emissions
7,8
7,8
(see note 1)
Sound power level, measured dB(A)
109
111
109
111
Sound power level, guaranteed L
Noise levels
dB(A)
WA
(see note 2)
Equivalent sound pressure level at the operator’s ear,
measured according to EN ISO 11806 and ISO 22868,
dB(A):
Equipped with grass blade (original)
Equipped with trimmer head (original)
Vibration levels
94
96
95
96
(see note 3)
Equivalent vibration levels (a
) at handles, measured
hv,eq
2
according to EN ISO 11806 and ISO 22867, m/s
Equipped with grass blade (original), left/right
Equipped with trimmer head (original), left/right
3,8/4,4
5,6/5,3
6,2/5,3
4,7/5,3
Note 1:Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC.Reported
WA
sound power level for the machine has been measured with the original cutting attachment that gives the highest level. The
difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in the
measurement result and the variations between different machines of the same model according to Directive 2000/14/EC.
Note 2: Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation)
of 1 dB (A).
2
Note 3: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Approved accessories
Type
Cutting attachment guard, Art. no.
Centre hole in blades/cutters, Ø 25,4 mm
Output shaft thread M12
Multi 255-4 (Ø 255 4 teeth)
Multi 275-4 (Ø 275 4 teeth)
Multi 300-3 (Ø 300 3 teeth)
523 09 54-01
523 09 54-01
523 09 54-01
Grass blade/grass cutter
Plastic blades
Polytrim Ø 300 mm (Separate blades
have part number 531 01 77-15)
523 09 54-01
Tap-N-Go 35 Spin (Ø 2.4 - 3.0 mm cord) 523 09 54-01
Tap-N-Go 45 Spin (Ø 2.7 - 3.3 mm cord) 523 09 54-01
Tap-N-Go 55 Spin (Ø 2.7 - 3.3 mm cord) 523 09 54-01
Trimmer head
Support cup
Trimmy S II (Ø 2.4 - 3.3 mm cord)
Fixed
523 09 54-01
-
EC-declaration of conformity (Applies to Europe only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the brush cutters Jonsered BC2043 and
BC2053 with serial numbers dating from 2009 onwards (the year is clearly stated on the rating plate, followed by the serial number),
comply with the requirements of the COUNCIL’S DIRECTIVE:
- of May 17, 2006 "relating to machinery" 2006/42/EC
- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according to
Annex V. For information relating to noise emissions, see the chapter Technical data.
The following standards have been applied: EN ISO 12100-2:2003, CISPR 12:2007, EN ISO 11806:2008
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type examination on
behalf of Husqvarna AB. The certificates are numbered: SEC/09/2065
Huskvarna December 29, 2009
Bo Jonsson, Development manager (Authorized representative for Husqvarna AB and responsible for technical documentation.)
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Poly Trim
1
2
<20mm
B
A
3
4
5
>20mm
7
6
6 Nm
!
8
X 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap n’ Go 35 Spin
1
2
3
8,5 m
28'
10 cm
4"
4,3 m
14'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap n’Go 45 Spin
1
2
3
10 m
32'
10 cm
4"
4,3 m
14'
4
5
7
6
8
15 cm
6"
"Clic"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap n’Go 55 Spin
1
2
3
B
C
2,7 - 4,0 mm / .105 - .160"
8 m / 26’
A
B
C 15 cm / 5.9"
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy SII
1
2
7,0 m
23'
12 cm
5"
~ 3,5 m
11'
3
4
~ 15 cm
7
5
6
6'
"Clic"
8
9
35-50 NM
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1152665-26
´®z+TbT¶6v¨
´®z+TbT¶6v¨
2009-11-06
Download from Www.Somanuals.com. All Manuals Search And Download.
|