Operating Instructions and Parts Manual
14-inch Deluxe Band Saw
Models: JWBS-14DX
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. M-710115
Revision D 7/04
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty.....................................................................................................................................2
Safety Warnings ......................................................................................................................4-5
Safety Decal ...............................................................................................................................6
Grounding Instructions ................................................................................................................7
115 Volt Operation ......................................................................................................................7
230 Volt Operation ......................................................................................................................8
Specifications .............................................................................................................................9
Fasteners..................................................................................................................................10
Receiving..................................................................................................................................11
Assembly ..................................................................................................................................11
Tilting the Table ........................................................................................................................14
Adjusting 90O Stop ....................................................................................................................14
Changing Blades.......................................................................................................................15
Adjusting Blade Tension............................................................................................................15
Adjusting Blade Tracking...........................................................................................................16
Adjusting Upper Blade Guide Assembly ....................................................................................16
Adjusting Upper Blade Guides & Blade Support Bearing ...........................................................17
Adjusting Lower Blade Guides & Blade Support Bearing ...........................................................18
Trouble-shooting .......................................................................................................................19
Parts Breakdowns:
Body Assembly..............................................................................................................20-23
Closed Stand Assembly .................................................................................................24-25
Optional Accessories.................................................................................................................26
Electrical Schematic – 115V......................................................................................................27
Electrical Schematic – 230V......................................................................................................28
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
As with all machines, there is a certain amount of hazard involved with the use of this band saw.
Use the machine with the respect and caution demanded where safety precautions are concerned.
When normal safety precautions are overlooked or ignored, personal injury to the operator can
result.
•
READ, UNDERSTAND AND FOLLOW the safety and operating instructions found in this
manual. Know the limitations and hazards associated with this machine.
•
•
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys
and adjusting wrenches are removed from the tool before turning it on.
•
•
KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DO NOT USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet
locations, or expose them to rain. Keep work area well lighted.
•
•
KEEP CHILDREN AWAY. All visitors should be kept a safe distance from the work area.
MAKE THE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing
starter keys.
•
•
•
DON’T FORCE THE TOOL. It will do the job better and safer at the rate for which it was
designed.
USE THE RIGHT TOOL. Don’t force a tool or attachment to do a job for which it was not
designed.
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersize cord will cause a drop in line voltage resulting in loss of power
and overheating. The table below shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Cord Length
Cord Gauge
115 volt
25’
230 volt
50’
16 AWG
16 AWG
14 AWG
12 AWG
50’
100’
150'
100’
200’
300'
•
•
WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is
dusty. NOTE: Common eyeglasses only have impact resistant lenses, they are NOT safety
glasses.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
•
SECURE WORK. Use clamps or a vise to hold the work when it’s practical. It’s safer than
using your hand and it frees both hands to operate the tool.
•
•
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
•
•
•
•
•
DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits
cutters, and the like.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off
position before plugging in the machine.
USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended
accessories. The use of improper accessories may cause a risk of injury.
NEVER STAND ON A TOOL. Serious injury could occur if the tool is tipped or if the cutting
tool is unintentionally contacted.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.
•
•
•
•
DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the
blade or cutter only.
NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don’t
leave the tool until it comes to a complete stop.
DRUGS, ALCOHOL, MEDICATION. Do not operate this machine while under the influence of
drugs, alcohol, or medication.
HEALTH HAZARDS. Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
* Lead from lead-based paint.
* Crystalline silica from bricks and cement and other masonry products.
* Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals, work in a well-ventilated area, and work with
approved safety equipment, such as those dust masks that are specifically designed to filter out
microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECAL
Familiarize yourself with the location and content of this decal on your machine.
Fig. 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric
shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
The conductor, with insulation having an outer surface that is green with or without yellow stripes, is
the equipment-grounding conductor. If repair or replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly grounded. Use only three
wire extension cords that have three-prong grounding plugs and three-pole receptacles that accept
the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your bandsaw is ready to run at 115 volt operation. This bandsaw,
when wired for 115 volts, is intended for use on a circuit that has an outlet and a plug that looks like
the one illustrated in Fig. 2. A temporary adapter, like the adapter in Fig. 3, may be used to connect
this plug to a two-pole receptacle, as shown in Fig. 3, if a properly grounded outlet is not available.
The temporary adapter should only be used until a properly grounded outlet can be installed by a
qualified electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug,
or tab, extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box, as shown in Fig. 3.
Download from Www.Somanuals.com. All Manuals Search And Download.
230 Volt Operation
If 230V, single-phase operation is desired, the following instructions must be followed:
1. Disconnect the machine from the power source.
2. This band saw is supplied with four motor leads that are connected for 115V operation, as
shown in Fig. 4. Reconnect these four motor leads for 230V operation, as shown in Fig. 5.
3. The 115V attachment plug supplied with the band saw must be replaced with a UL/CSA listed
plug suitable for 230V operation (Fig. 6). Contact your local authorized WMH Tool Group
service center or qualified electrician for proper procedures to install the plug. The band saw
must comply with all local and national codes after the 230 volt plug is installed.
4. The band saw with a 230 volt plug should only be connected to an outlet having the same
configuration (Fig. 6). No adapter is available or should be used with the 230 volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly
grounded. If you are not sure, have a registered electrician check the receptacle.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
JWBS-14DX Band Saw
Stock Number.................................................................................................................710115K
Cutting Capacity (height)............................................................................................................6”
Cutting Capacity (width) .....................................................................................................13-1/2”
Minimum Blade Width.............................................................................................................1/8”
Maximum Blade Width............................................................................................................3/4”
Blade Length......................................................................................................................93-1/2”
Blade Speed .............................................................................................................. 3000 SFPM
Table Size.......................................................................................................................15” x 15”
Table Slot Size........................................................................................................3/8”D x 3/4”W
Table Height from Floor .....................................................................................................43-1/2”
Table Tilt (L-R)..............................................................................................................45°R / 10°
Dust Chute Diameter......................................................................................................... 4” O.D.
Overall Dimensions........................................................................................68”H x 26”W x 19”D
Motor .............................................................................1.25 HP, 1Ph, 115/230V (prewired 115V)
Net Weight (approx.).......................................................................................................... 185 lb.
Shipping Weight (approx.).................................................................................................. 197 lb.
The specifications in this manual are given as general information and are not binding. WMH Tool
Group reserves the right to effect, at any time and without prior notice, alterations to parts, fittings,
and accessory equipment deemed necessary for any reason whatsoever.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Fasteners for JWBS-14DX
A. Saw Body to Stand
4 – M8x40 hex cap screws
(approx. 1-1/2" long)
8 – M8 flat washers
4 – M8 lock washers
4 – M8 hex nuts
B. Strain Relief Plate to Stand
2 – M5x12 pan head machine screws
C. Belt Cover to Base
2 – Knobs
D. Trunnion Bracket to Saw Body
2 – M8x30 hex cap screws
(approx. 1-1/4" long)
2 – M8 lock washers
1 – M8x80 hex cap screw (for table stop -
(approx. 3-1/8” long)
1 – M8 hex nut
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving
Open both shipping containers and check for shipping
damage. Report any damage immediately to your
distributor and shipping agent. Read the instruction
manual thoroughly for assembly, maintenance and
safety instructions.
Contents of Shipping Containers
Container One
1
Stand with motor
Container Two
1
1
1
1
1
2
1
1
1
1
1
Saw body
V-belt
Belt cover
Trunnion support bracket
Table
Table lock knobs
Table pin
Table insert
Fastener package (see fastener page)
Instruction manual
Warranty card
Tools Required for Assembly
3/8" to 1" combination wrench set and
adjustable wrench
#1 and #2 cross point screwdrivers
Assembly
Exposed metal surfaces, such as the table, have
been given a protective coating. This should be
cleaned with a soft cloth and solvent, such as
kerosene. Do not use an abrasive pad, and do not
get solvents on plastic parts.
1. Remove belt cover from inside of stand.
2. Place cabinet stand upright on a level surface. If
desired, the stand can be further stabilized by
securing it to the floor with lag screws through
the inside corner holes. If using a mobile base,
lock the casters before assembling or operating
the band saw.
3. With the aid of a second person, lift the saw
body out of the shipping container and place
onto stand top. Be sure front of saw (with JET
logo) faces stand front (JET logo).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Saw body is heavy! Use caution when lifting
and stabilize until firmly attached to the
stand! Failure to comply may cause
serious injury!
4. Line up holes in saw body with holes in the top
of the stand. Fasten saw body to the stand with
four M8 x 40 hex cap screws, eight M8 washers,
four M8 lock washers, and four M8 hex nuts (as
shown in item A, page 10).
5. Push motor cord and strain relief plate through
the opening in the side of the stand (Fig. 8).
Fasten the strain relief plate to the stand with
two M5 x 12 pan head machine screws (shown
in item B, page 10).
6. Check the alignment of the pulleys by placing a
straight edge against the flat sides of the motor
and wheel pulleys (Fig. 8a). If the pulleys lie in a
straight plane (Fig. 8b) they are aligned. If they
do not lie in a straight plane, loosen the set
screw on one of the pulleys and shift the pulley
in or out until both pulleys lie in a straight plane.
Tighten set screw.
7. Open the lower door, and place the v-belt
around the motor pulley and the wheel pulley
(see Fig. 8a).
8. Loosen the nuts on the four motor mounting
bolts (Fig. 8c) and tension the v-belt by pushing
down on the motor. Tighten the four motor
mounting nuts.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
9. The v-belt is properly tensioned when finger
pressure between the two pulleys causes
approximately 1/2" deflection (fig. 8d).
10. Screw the two small knobs (Fig. 9) into the
threaded holes in the saw body. Slide the pulley
cover down over the knobs, and tighten the
knobs.
11. Attach trunnion support to saw body with two M8
x 30 hex cap screws and two M8 lock washers
(as in item D, page two). See Figure 12.
12. Thread nut on to table stop bolt (Fig. 12) and
attach to trunnion support bracket as shown.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
13. To mount the table, remove pin and insert from
the table (Fig. 13).
14. Rotate the table so that the saw blade will slide
through the slot in the table. Then orient the
table so the screws will slide into the holes on
the trunnion support brac ket. Attach lock knobs
to these screws (Fig. 13).
15. Replace pin and insert.
16. Connect the plugs of the motor cord and switch
cord (Fig. 13a).
17. Transportation and handling may have caused
some fasteners to loosen. Before operating,
check all screws, bolts, and nuts to make sure
they are snug. Operate machine only after
reading the entire manual including blade
tracking, blade guide adjustments, and safety
rules.
Tilting the Table
WARNING
Unplug the machine from the power
source before making any repair or adjustment!
Failure to comply may cause serious injury!
1.
2.
Loosen two lock knobs (Fig. 14).
Tilt table up to 45 degrees to the right or up to
10 degrees to the left, using the scale mounted
to the trunnion.
3.
Tighten two lock knobs (Fig.14).
Note: Table stop must be removed to tilt table to the
left.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting 90° Table Stop
1.
2.
Disconnect machine from the power source.
Loosen lock knobs (Fig. 14) and tilt table left
until it rests against table stop.
3.
Use a square placed on the table and against
the blade (Fig. 15) to see if the table is 90
degrees to the blade.
4.
5.
If an adjustment is necessary, loosen lock
knobs, tilt table to the right, and lock in place.
Loosen jam nut and turn table stop (Fig. 14) left
or right to raise or lower the stop. Tighten jam
nut to hold table stop in place.
6.
7.
Unlock table, tilt back onto table rest and
confirm table is 90 degrees with the blade.
If necessary, adjust scale pointer to zero.
Changing Blades
WARNING
Blade teeth are sharp! Use care when
handling the saw blade.
Failure to comply may cause serious injury!
1.
Disconnect machine from power source.
2.
Loosen blade tension by pushing up on the
release lever (Fig. 16).
3.
4.
5.
Remove the table insert and the table pin.
Open both wheel covers.
Remove the blade from between upper and
lower blade guides. Remove blade from upper
and lower wheels. Turn blade to direct through
slot in table.
6.
Guide new blade through table slot. Place
blade in upper and lower blade guides. Note:
Make sure blade teeth point down toward table.
7.
8.
Place blade in the middle of the upper and
lower wheel.
Replace table insert and table pin.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Tension and track blade before operating saw.
Find instructions for tensioning and tracking the
blade under "Adjusting Blade Tension" and
"Adjusting Blade Tracking".
Adjusting Blade Tension
1.
2.
Disconnect machine from power source.
Turn blade tension knob (Fig. 16) clockwise to
tension blade. A gauge on the upper wheel
slide bracket indicates the approximate tension
according to the width of the blade. Initially, set
the blade tension to correspond to blade width.
3.
4.
As you become familiar with the saw, you may
find it necessary to change the blade tension
from the initial setting. Changes in blade width
and the type of material being cut will have an
effect on blade tension.
Keep in mind that too little or too much blade
tension can cause blade breakage.
Adjusting Blade Tracking
WARNING
Disconnect machine from the power source!
Never adjust blade tracking with the
machine running!
Failure to comply may cause serious injury!
“Tracking” refers to how the blade is situated upon
the wheels while in motion. The blade should track in
the center of both wheels.
1.
The blade must be properly tensioned before
adjusting blade tracking. The release lever
should be in the down (tensioned) position.
Make sure blade guides and blade bearings do
not interfere with the blade.
2.
3.
Open top blade cover. Rotate the wheel
forward and observe the position of the blade on
the wheel - it should be in the center of the
wheel. See Fig. 17a.
If adjustment is necessary, loosen wing nut (Fig.
17), and tighten tracking knob slightly to move
blade toward rear of machine. Slightly
loosening the tracking knob will cause the blade
to track toward the front of the machine.
4.
Tighten wing nut after blade is tracking in the
center of the wheel.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Upper Blade Guide Assembly
1.
Disconnect machine from the power source.
2.
3.
Loosen lock knob (A, Fig. 18) and raise or lower
upper blade guide assembly (B, Fig. 18) to just
above the material being cut.
Tighten lock knob. Make sure blade guide
blocks (C, Fig. 18) are still flat to the blade. If
adjustment is necessary, loosen lock knob (A,
Fig. 18) and rotate assembly until guide blocks
are flat to blade.
4.
The upper blade guide is spring loaded. To
adjust the tension on the spring, remove knob
(A, Fig. 18), tighten or loosen set screw (D, Fig.
18) until desired tension is reached, and replace
knob.
Adjusting Upper Blade Guide and
Blade Support Bearing
WARNING
Blade guard has been removed for picture
clarity. Never operate the bandsaw without
all guards in place and in working order!
Failure to comply may cause serious injury!
1.
Disconnect machine from the power source.
2.
3.
Blade must already be tensioned and tracking
properly.
Loosen thumb screws (A, Fig. 19) and move
guide blocks (B, Fig. 19) as close to the blade
as possible without pinching it.
4.
5.
Tighten thumb screws (A, Fig. 19).
Loosen thumb screw (C, Fig. 19) and turn
knurled knob (D, Fig. 19) to move the guide
block bracket in or out until the front edge of the
guide blocks are just behind the "gullets" of the
saw teeth.
6.
7.
Tighten thumb screw (C, Fig. 19).
Loosen thumb screw (E, Fig. 19) and turn
knurled knob (F, Fig. 19) to move the support
bearing (G, Fig. 19) in or out until the bearing is
1/64" behind the blade.
8.
Tighten thumb screw (E, Fig. 19).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
The blade support bearing should be adjusted
so that the back edge of the blade overlaps the
front face of the ball bearing approximately 1/8".
To change position of the bearing, remove
screw (H, Fig. 19), and bearing (G, Fig. 19), and
back off knurled knob (F, Fig. 19) completely to
remove the bearing shaft. Notice the bearing
holder on the shaft is eccentric. Re-install the
bearing shaft, the bearing, and the screw.
Examine the overlap between the bearing face
and the blade. Change the position of the
bearing shaft until the overlap is approximately
1/8".
Adjusting Lower Blade Guides and Blade
Support Bearing
1.
2.
Disconnect machine from the power source.
Blade must already be tensioned and tracking
properly.
3.
Loosen thumb screws (A, Fig. 20) and move
guide blocks (B, Fig. 20) as close to blade as
possible without pinching it.
4.
5.
Tighten thumb screws (A, Fig. 20).
Loosen thumb screw (C, Fig. 20) and turn
knurled knob (D, Fig. 20) to move the guide
block bracket in or out until the front edge of the
guide blocks are just behind the "gullets" of the
saw teeth.
6.
7.
Tighten thumb screw (C, Fig. 20).
Loosen thumb screw (E, Fig. 20) and turn
knurled knob (F, Fig. 20) to move the support
bearing (G, Fig. 20) in or out until the bearing is
1/64" behind the blade.
8.
9.
Tighten thumb screw (E, Fig. 20).
The blade support bearing should be adjusted
so that the back edge of the blade overlaps the
front face of the ball bearing approximately 1/8".
To change position of the bearing, remove
screw (H, Fig. 20) and bearing (G, Fig. 20), and
back off knurled knob (F, Fig. 20) completely to
remove the bearing shaft.
10. Notice the bearing holder on the shaft is
eccentric. Re-install the bearing shaft, the
bearing, and the screw. Examine the overlap
between the bearing face and the blade.
Change the position of the bearing shaft until
the overlap is approximately 1/8". Re-tighten
thumb screw (E, Fig. 20).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING (JWBS-14DX Band Saw)
PROBLEM
POSSIBLE CAUSE
SOLUTION
Saw stops or will not start
1. Saw unplugged
1. Check plug connections
2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset
circuit breaker
3. Cord damaged
3. Replace cord
Does not make accurate
45 deg. or 90 deg. cuts
1. Stop not adjusted correctly
2. Angle pointer not set accurately
3. Miter gauge out of adjustment
1. Check blade with
square and adjust stop
2. Check blade with square
and adjust pointer
3. Adjust miter gauge
Blade wanders during cut
1. Fence not aligned with blade
2. Warped wood
1. Check and adjust fence
2. Select another piece of
wood
3. Excessive feed rate
4. Incorrect blade for cut
3. Reduce feed rate
4. Change blade to correct
type
5. Blade tension not set properly
6. Guides not set properly
5. Set blade tension
according to blade size
6. Adjust guides
Saw makes unsatisfactory
cuts
1. Dull blade
1. Replace blade
2. Blade mounted wrong
3. Gum or pitch on blade
4. Incorrect blade for cut
2. Teeth should point down
3. Remove blade and clean
4. Change blade to correct
type
5. Gum or pitch on table
5. Clean table
Blade does not come up
size and to speed
1. Extension cord too light or too long
2. Low shop voltage
1. Replace with adequate
length cord
2. Contact your local electric
company
Saw vibrates excessively
1. Base on uneven floor
1. Reposition on flat, level
surface
2. Bad v-belt
3. Motor mount is loose
2. Replace v-belt
3. Tighten motor mount
hardware
4. Loose hardware
4. Tighten hardware
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
JWBS-14DX Body Assembly
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
JWBS-14DX Body Assembly
Index Part
No. No.
Description
Size
Qty.
1 ......... 150100AW ...................Upper Arm Frame .............................................. ................................ 1
2 ......... 150037W......................Table.................................................................. ................................ 1
3 ......... 100038 .........................Table Pin ........................................................... ................................ 1
4 ......... 708719 .........................Guide Block ....................................................... ................................ 4
5 ......... 150005A.......................Upper Support Bracket Post............................... ................................ 1
6 ......... 150006A.......................Support Bracket ................................................. ................................ 2
7 ......... 150007A.......................Guide Post..................................................... ... ................................ 1
8 ......... TS-1490021..................Hex Cap Screw..................................................M8x16...................... 2
9 ......... TS-1550061..................Flat Washer .......................................................M8 ........................... 1
10 ....... 150010A.......................Nut..................................................................... ................................ 4
11 ....... 990708 .........................Screw.................................................................M8x40...................... 2
12 ....... TS-1482031..................Hex Cap Screw..................................................M6x16...................... 1
13 ....... 150013A.......................Thumb Screw.....................................................M6x16...................... 3
14 ....... 150014A.......................Thumb Screw ....................................................M6x12...................... 5
15 ....... 150015A.......................Upper Spacing Sleeve ................................... ... ................................ 2
16 ....... BB-6200ZZ...................Ball Bearing .......................................................6200ZZ .................... 2
17 ....... 990908 .........................Pan Head Screw*...............................................M6x8........................ 2
18 ....... 100002A.......................Upper Wheel Blade Guard ................................. ................................ 1
19 ....... TS-148201....................Hex Cap Screw..................................................M6X10 ..................... 2
20 ....... TS-1550041..................Flat Washer .......................................................M6 ........................... 4
21 ....... 990651 .........................Lock Knob..........................................................M10x30.................... 1
22 ....... 199037 .........................Table Insert........................................................ ................................ 1
23 ....... 992311 .........................Spring Pin.......................................................... ................................ 1
25 ....... TS-1482041..................Hex Cap Screw..................................................M6x20...................... 2
26 ....... 150024 .........................Catch Knob........................................................ ................................ 2
27 ....... TS-1551061..................Lock Washer*.....................................................M8 ......................2(2)*
28 ....... 150028W......................Inner Wheel Cover............................................. ................................ 1
29 ....... 155029W......................Outer Wheel Cover............................................ ................................ 1
30 ....... 100031 .........................Pin ..................................................................... ................................ 4
31 ....... 990180 .........................Hex Head Bolt....................................................M16x55.................... 1
32 ....... WF164030....................Washer ..............................................................M16.......................... 2
33 ....... TS-1540101..................Hex Nut..............................................................M16.......................... 1
34 ....... JWBS14DX-134 ...........Base .................................................................. ................................ 1
35 ....... 110045 .........................Trunnion Support Bracket................................... ................................ 1
36 ....... 100042 .........................Trunnion............................................................. ................................ 2
37 ....... 100051 .........................Scale.................................................................. ................................ 1
38 ....... 100041 .........................Trunnion Clamp Shoe ........................................ ................................ 2
39 ....... TS-1491081..................Hex Cap Screw..................................................M10x50.................... 2
40 ....... TS-1482021..................Hex Cap Screw..................................................M6x12...................... 6
41 ....... 110049 .........................Pointer ............................................................... ................................ 1
42 ....... 990821 .........................Pan Head Screw ................................................M5x6........................ 5
43 ....... TS-1490151..................Hex Cap Screw*.................................................M8x80...................... 1
44 ....... TS-1540061..................Nut*....................................................................M8 ........................... 1
45 ....... TS-1490051..................Hex Cap Screw*.................................................M8X30 ..................... 2
46 ....... 990554 .........................Lock Knob.......................................................... ............................... 2
47 ....... TS-152303....................Socket Set Screw...............................................M6x10...................... 1
48 ....... 100063 .........................Belt Pulley.......................................................... ................................ 1
49 ....... 992547 .........................Retaining Ring ................................................... ................................ 1
50 ....... 110065 .........................Lower Wheel Shaft............................................. ................................ 1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
JWBS-14DX Body Assembly
Index Part
No. No.
Description
Size
Qty.
51........992009......................... Key.................................................................... 5x5x20......................2
52........BB-6204RS.................. Ball Bearing....................................................... 6204RS ....................2
53........990293......................... Hex Head Bolt (Left Thread).............................. M8x25 ......................1
54........150054......................... Hex Head Bolt ................................................... .................................2
55........150055......................... Lower Support Bracket Post............................... .................................1
56........150056......................... Switch Backing Plate ......................................... .................................1
57........523028......................... Switch Box......................................................... .................................1
58........994542......................... Switch................................................................ .................................1
59........995001......................... Power Cord (Switch To Motor)........................... .................................1
60........995002......................... Power Cord (Switch To Power Soure)................ .................................1
61........990814......................... Self Tapping Screw............................................ M3.5x19 ...................2
62........TS-1550021 ................. Flat Washer ...................................................... M4............................2
63........TS-1533042 ................. Phillips Pan Head Machine Screw...................... M5x12 ......................6
64........523024......................... Wire Clip ........................................................... .................................1
65........TS-1533032 ................. Phillips Pan Head Machine Screw...................... M5x10 ......................4
66........150066......................... Stud................................................................... .................................2
67........150902......................... Lower Hinge ...................................................... .................................1
68........WF051210 ................... Washer.............................................................. M5............................2
69........JWBS14DX-169........... Lower Wheel Guard........................................... .................................1
70........100185......................... Lower Wheel ..................................................... .................................1
71........100025A ...................... Wheel Protector................................................. .................................2
72........100186......................... Upper Wheel ..................................................... .................................1
73........992522......................... Retaining Ring................................................... R35...........................2
74........BB-6202ZZ................... Ball Bearing....................................................... 6202ZZ.....................2
75........TS-1540083 ................. Hex Nut ............................................................. M12x1.25..................1
76........ .................................... Saw Blade (Local Purchase).............................. .................................1
77........990804......................... Self Tapping Screw............................................ M4x8 ......................16
78........150901......................... Upper Hinge ...................................................... .................................1
79........150079......................... Catch................................................................. .................................2
80........150080......................... Clip.................................................................... .................................2
81........150081......................... Bracket.............................................................. .................................2
82........110070......................... Blade Guard ...................................................... .................................1
83........990811......................... Self Tapping Screw............................................ M3.5x12 ...................2
............100016ACP.................. Sliding Bracket Assy (includes items 84 thru 88) .................................1
84........100016A....................... Sliding Bracket .................................................. .................................1
85........100019......................... Shaft Hinge........................................................ .................................1
86........150086......................... Upper Wheel Shaft ............................................ .................................1
87........100021......................... Steel Pin............................................................ .................................2
88........992314......................... Spring Pin.......................................................... .................................1
89........100015A....................... Coil Spring......................................................... .................................1
90........150090......................... Square Nut ........................................................ .................................1
91........990652......................... Lock Knob ......................................................... .................................1
92........NW080000................... Wing Nut ........................................................... M8............................1
93........JWBS14DX-193........... Blade Adjusting Screw....................................... .................................1
95........TS-1490071 ................. Hex Cap Screw* ................................................ M8x40 ......................4
96........TS-1550061 ................. Flat Washer*...................................................... M8............................4
97........150097......................... Washer.............................................................. .................................2
98........994181......................... Steel Ball........................................................... .................................1
99........150099......................... Spring................................................................ .................................1
100......TS-1525011 ................. Socket Set Screw .............................................. M10x10 ....................1
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
JWBS-14DX Body Assembly
Index Part
No. No.
Description
Size
Qty.
101...... 150101 .........................Lower Wheel Blade Guard ................................. ................................ 1
102...... WE050000 ...................Gear Washer .....................................................M5 ........................... 2
103...... 998654 .........................Strain Relief ....................................................... ................................ 2
104...... 100018 .........................Indicator............................................................. ................................ 1
105...... WI080000.....................Gear Washer .....................................................M8 ........................... 2
106...... 100174 .........................Fixed Collar ....................................................... ................................ 1
107...... TS-1522031..................Socket Set Screw...............................................M5x10...................... 1
108...... 130044 .........................Fixed Collar ....................................................... ................................ 1
109...... SS050100.....................Socket Set Screw...............................................M5x5........................ 1
110...... TS-1550071..................Flat Washer .......................................................M10.......................... 1
111...... 100234 .........................Tension Lever Knob...........................................M8 ........................... 1
112...... 100183 .........................Tension Lever Rod............................................. ................................ 1
113...... NH121900 ....................Hex Nut..............................................................M12.......................... 1
114...... 100205 .........................Gasket ...............................................................M8 ........................... 1
115...... 100182 .........................Tension Lever.................................................... ................................ 1
116...... 100176 .........................Bushing.............................................................. ................................ 1
117...... TS-2248202..................Socket Head Button Screw.................................M8x20...................... 1
118...... 100177 .........................Spacer ............................................................... ................................ 1
119...... TS-1490071..................Hex Cap Screw..................................................M8x40...................... 2
120...... TS-1541031..................Nylon Lock Hex Nut ...........................................M8 ........................... 2
121...... TS-1550061..................Flat Washer .......................................................M8 ........................... 6
122...... 100178 .........................Support Plate ..................................................... ................................ 2
123...... 100179 .........................Fixed Base......................................................... ................................ 1
124...... TS-2361081..................Lock Washer......................................................M8 ........................... 2
125...... TS-2248202..................Socket Head Button Screw.................................M8x20...................... 2
........... JWBS14-HK.................Hardware Kit (not shown) ................................... ................................ 1
* included in hardware kit
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
JWBS-14DX Closed Stand Assembly
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
JWBS-14DX Closed Stand Assembly
Index Part
No. No.
Description
Size
Qty.
1 ......... 150501W......................Stand ................................................................. ............................... 1
2 ......... 150502W......................Door................................................................... ............................... 1
3 ......... 150503 .........................Door Latch Assembly (Items 4 & 5).................... ............................... 1
4 ......... WBS14CS-04...............Washer .............................................................. ............................... 2
5 ......... WBS14CS-05...............Pan Head Screw ................................................M4x5....................... 2
6 ......... PG-M02........................Plaque ............................................................... ............................... 1
7 ......... TS-1533031..................Flat Head Screw.................................................M5x10..................... 2
8 ......... 150508W......................Plate .................................................................. ............................... 1
9 ......... 998621 .........................Stran Relief........................................................ ............................... 1
10 ....... TS-1533042..................Pan Head Screw*...............................................M5x12..................... 2
11 ....... 150511W......................Motor Plate ........................................................ ............................... 1
12 ....... 100180 .........................Motor (TEFC).......................................1-1/4 HP, 1Ph, 115/230V....... 1
13 ....... 600013 .........................Motor Pulley....................................................... ............................... 1
14 ....... VB-A50.........................V-Belt................................................................. ............................... 1
15 ....... TS-1523011..................Set Screw ..........................................................M6x6....................... 1
16 ....... 100254 .........................Belt Cover.......................................................... ............................... 1
17 ....... PWBS14-306................Knob*.................................................................M6x12..................... 2
20 ....... TS-1490041..................Hex Head Bolt....................................................M8x25..................... 4
21 ....... 991516 .........................Square Neck Bolt ...............................................M8x16..................... 4
22 ....... TS-1550051..................Washer*.............................................................M8 ...................16(4)*
23 ....... TS-155108....................Lock Washer*.....................................................M8 ...................12(4)*
24 ....... TS-1540061..................Nut*....................................................................M8 ...................12(4)*
26 ....... 995003A.......................Motor Cord......................................................... ............................... 1
27 ....... 150527 .........................Pad.................................................................... ............................... 2
........... WBS14CS-HK..............Hardware Kit (includes items marked with *)....... ............................... 1
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories for JWBS-14DX Band Saw
708114 Three speed kit for WBS-14CS
Produces speeds of 965, 1470, and 2465 SPFM. Includes four step motor pulley,
intermediate pulley, V-belts, fasteners, and mounting instructions with parts list.
708718 JRF-14 Rip Fence Assembly
Includes guide bars, rip fence assembly, fasteners, and mounting instructions with parts list.
708717 JRB-14 Riser Block Kit
Increases depth of cut from 6" maximum to 12" maximum. Includes 6" cast block, long
frame bolt, front and back blade guards, and mounting instructions with parts list.
(Blade not included - requires 105-1/2" blade).
708716 JMG-14 Miter Gauge Assembly
For straight and angle cutting. Includes guide bar, pivoting support body, and adjustable
stops.
708719 JRB-14 Blade Block Set
Includes upper and lower replacement blocks made from a non-metallic composite material
with a dry lubricant to reduce friction and heat.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
JWBS-14DX Electrical Schematic – 115V
27
Download from Www.Somanuals.com. All Manuals Search And Download.
JWBS-14DX Electrical Schematic - 230V
WMH TOOL GROUP
2420 Vantage Drive
Elgin, IL 60123
Ph: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|