Jet Tools Saw JPS 10TS User Manual

This .pdf document is bookmarked  
Operating Instructions and Parts Manual  
10-inch ProShop Table Saw  
with Riving Knife  
Model JPS-10TS  
(shown with steel wings and 30” rail set)  
for serial no. 11120136 and higher  
WALTER MEIER (Manufacturing) Inc.  
427 New Sanford Road  
LaVergne, Tennessee 37086  
Ph.: 800-274-6848  
Part No. M-708490  
Revision B1 04/2012  
Copyright © 2012 Walter Meier (Manufacturing) Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.0 Table of contents  
Section  
Page  
1.0 Warranty and service....................................................................................................................2  
2.0 Table of contents..........................................................................................................................3  
3.0 Safety warnings ...........................................................................................................................4  
3.1 Kickback ..................................................................................................................................5  
4.0 About this manual ........................................................................................................................6  
5.0 Glossary......................................................................................................................................7  
6.0 Features......................................................................................................................................8  
7.0 Specifications...............................................................................................................................8  
8.0 Setup and assembly...................................................................................................................10  
8.1 Shipping contents ...................................................................................................................10  
8.2 Unpacking and cleanup...........................................................................................................11  
8.3 Installing legs..........................................................................................................................11  
8.4 Handwheels ...........................................................................................................................11  
8.5 Extension wings......................................................................................................................12  
8.6 Extension wing adjustment ......................................................................................................12  
8.7 Rails and fence.......................................................................................................................12  
8.8 Wood extension table..............................................................................................................12  
8.9 Switch bracket........................................................................................................................12  
8.10 Dust Hood ............................................................................................................................12  
8.11 Riving knife...........................................................................................................................13  
8.12 Anti-kickback pawls...............................................................................................................13  
8.13 Blade guard..........................................................................................................................14  
8.14 Blade installation/replacement ...............................................................................................14  
8.15 Aligning blade guard and riving knife ......................................................................................15  
8.16 Low profile riving knife...........................................................................................................15  
8.17 Table insert ..........................................................................................................................15  
8.18 Miter gauge ..........................................................................................................................15  
9.0 Electrical connections.................................................................................................................16  
9.1 Grounding instructions ............................................................................................................16  
9.2 Voltage conversion .................................................................................................................16  
9.3 Overload reset button..............................................................................................................17  
9.4 Extension cords......................................................................................................................17  
9.5 On-off switch padlock..............................................................................................................17  
10.0 Adjustments.............................................................................................................................17  
10.1 Blade raising/tilt mechanism ..................................................................................................17  
10.2 Adjusting 45º and 90º positive stops.......................................................................................17  
10.3 Table to blade alignment .......................................................................................................19  
11.0 Operations...............................................................................................................................19  
12.0 Safety devices..........................................................................................................................24  
13.0 Maintenance ............................................................................................................................25  
14.0 Optional accessories ................................................................................................................26  
15.0 Troubleshooting the JPS-10TS..................................................................................................27  
16.0 Replacement Parts...................................................................................................................27  
16.1.1 Motor and Trunnion – Exploded View ..................................................................................28  
16.1.2 Motor and Trunnion – Parts List ..........................................................................................29  
16.2.1 Table and Cabinet – Exploded View ....................................................................................32  
16.2.2 Table and Cabinet – Parts List ............................................................................................33  
16.3.1 Stand Assembly – Exploded View .......................................................................................35  
16.3.2 Stand Assembly – Parts List ...............................................................................................35  
16.4.1 Cast Iron Wings – Exploded View........................................................................................36  
16.4.2 Cast Iron Wings – Parts List................................................................................................36  
17.1 Electrical Connections – 115V...................................................................................................37  
17.2 Electrical Connections – 230V...................................................................................................38  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lead from lead based paint.  
Crystalline silica from bricks, cement and  
other masonry products.  
Arsenic and chromium from chemically  
treated lumber.  
3.0 Safety warnings  
1. Read and understand the entire owner's  
manual before attempting assembly or  
operation.  
Your risk of exposure varies, depending on  
how often you do this type of work. To  
reduce your exposure to these chemicals,  
work in a well-ventilated area and work with  
approved safety equipment, such as face or  
dust masks that are specifically designed to  
filter out microscopic particles.  
2. Read and understand the warnings posted  
on the machine and in this manual. Failure  
to comply with all of these warnings may  
cause serious injury.  
12. Do not operate this machine while tired or  
under the influence of drugs, alcohol or any  
medication.  
3. Replace the warning labels if they become  
obscured or removed.  
4. This table saw is designed and intended for  
use by properly trained and experienced  
personnel only. If you are not familiar with  
the proper and safe operation of a table  
saw, do not use until proper training and  
knowledge have been obtained.  
13. Make certain the switch is in the OFF  
position before connecting the machine to  
the power supply.  
14. Make certain the machine is properly  
grounded.  
5. Do not use this table saw for other than its  
intended use. If used for other purposes,  
Walter Meier (Manufacturing) Inc., disclaims  
any real or implied warranty and holds itself  
harmless from any injury that may result  
from that use.  
15. Make  
all  
machine  
adjustments  
or  
maintenance with the machine unplugged  
from the power source.  
16. Remove adjusting keys and wrenches. Form  
a habit of checking to see that keys and  
adjusting wrenches are removed from the  
machine before turning it on.  
6. Always wear approved safety glasses/face  
shields while using this table saw. Everyday  
eyeglasses only have impact resistant  
lenses; they are not safety glasses.  
17. Keep safety guards in place at all times  
when the machine is in use. If removed for  
maintenance purposes, use extreme caution  
and replace the guards immediately after  
completion of maintenance.  
7. Before operating this table saw, remove tie,  
rings, watches and other jewelry, and roll  
sleeves up past the elbows. Remove all  
loose clothing and confine long hair. Non-  
slip footwear or anti-skid floor strips are  
recommended. Do not wear gloves.  
18. Check damaged parts. Before further use of  
the machine, a guard or other part that is  
damaged should be carefully checked to  
determine that it will operate properly and  
perform its intended function. Check for  
alignment of moving parts, binding of  
moving parts, breakage of parts, mounting  
and any other conditions that may affect its  
operation. A guard or other part that is  
damaged should be properly repaired or  
replaced.  
8. Always use the blade guard on all ''through-  
sawing'' operations.  
A
through-sawing  
operation is one in which the blade cuts  
completely through the workpiece.  
9. Kickback occurs when the workpiece is  
thrown towards the operator at a high rate of  
speed. If you do not have  
a
clear  
understanding of kickback and how it  
occurs, DO NOT operate this table saw!  
19. Provide for adequate space surrounding  
work area and non-glare, overhead lighting.  
10. Wear ear protectors (plugs or muffs) during  
extended periods of operation.  
20. Keep the floor around the machine clean  
and free of scrap material, oil and grease.  
11. Some dust created by power sanding,  
sawing, grinding, drilling and other  
construction activities contain chemicals  
known to cause cancer, birth defects or  
other reproductive harm. Some examples of  
these chemicals are:  
21. Keep visitors a safe distance from the work  
area. Keep children away.  
22. Make your workshop child proof with  
padlocks, master switches or by removing  
starter keys.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
23. Give your work undivided attention. Looking  
around, carrying on a conversation and  
“horse-play” are careless acts that can result  
in serious injury.  
Kickback can also result in the operator’s hands  
being pulled into the blade.  
Kickback Prevention  
Tips to avoid the most common causes of  
kickback:  
24. Maintain a balanced stance at all times so  
that you do not fall into the blade or other  
moving parts. Do not overreach or use  
excessive force to perform any machine  
operation.  
Make sure the riving knife is always aligned  
with the blade. A workpiece can bind or stop  
the flow of the cut if the riving knife is  
misaligned, and result in kickback.  
25. Use the right tool at the correct speed and  
feed rate. Do not force a tool or attachment  
to do a job for which it was not designed.  
The right tool will do the job better and more  
safely.  
Use a riving knife during every cut. The  
riving knife maintains the kerf in the  
workpiece, which will reduce the chance of  
kickback.  
26. Use recommended accessories; improper  
accessories may be hazardous.  
Never attempt freehand cuts. The workpiece  
must be fed parallel to the blade, otherwise  
kickback will likely occur. Always use the rip  
fence or miter gauge to support the  
workpiece.  
27. Maintain tools with care. Keep saw blades  
sharp and clean for the best and safest  
performance.  
Follow  
instructions  
for  
lubricating and changing accessories.  
Make sure that rip fence is parallel to blade.  
If not, the chances of kickback are very high.  
Take the time to check and adjust the rip  
fence.  
28. Turn off the machine before cleaning. Use a  
brush or compressed air to remove chips or  
debris — do not use your hands.  
Feed cuts through to completion. Anytime  
you stop feeding a workpiece that is in the  
middle of a cut, the chance of binding,  
resulting in kickback, is greatly increased.  
29. Do not stand on the machine. Serious injury  
could occur if the machine tips over.  
30. Never  
leave  
the  
machine  
running  
unattended. Turn the power off and do not  
leave the machine until it comes to a  
complete stop.  
Protection Tips from Kickback  
Kickback can happen even if precautions are  
taken to prevent it. Listed below are some tips to  
protect you if kickback does occur:  
31. Remove loose items and unnecessary work  
pieces from the area before starting the  
machine.  
Stand to the side of the blade when cutting.  
An ejected workpiece usually travels directly  
in front of the blade.  
32. Keep hands out of the line of saw blade.  
33. Use a push-stick when required.  
34. Pay particular attention to instructions on  
reducing risk of kickback.  
Wear safety glasses or a face shield. Your  
eyes and face are the most vulnerable part  
of your body.  
35. Do not perform any operation freehand.  
36. Never reach around or over saw blade.  
Never place your hand behind the blade. If  
kickback occurs, your hand will be pulled  
into the blade.  
37. Don’t use in dangerous environment. Don’t  
use power tools in damp or wet location, or  
expose them to rain. Keep work area well  
lighted.  
Use a push stick to keep your hands farther  
away from the moving blade. If a kickback  
occurs, the push stick will most likely take  
the damage that your hand would have  
received.  
3.1 Kickback  
The most common accidents among table saw  
users, according to statistics, can be linked to  
kickback, the high-speed expulsion of material  
from the table that can strike the operator.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Familiarize yourself with the following safety notices used in this manual:  
This means that if precautions are not heeded, it may result in minor injury and/or  
possible machine damage.  
This means that if precautions are not heeded, it may result in serious injury or possibly  
even death.  
4.0 About this manual  
This manual is provided by Walter Meier (Manufacturing) Inc. covering the safe operation and  
maintenance procedures for a JET Model JPS-10TS ProShop™ Table Saw. This manual contains  
instructions on installation, safety precautions, general operating procedures, maintenance instructions  
and parts breakdown. Your machine has been designed and constructed to provide years of trouble-free  
operation if used in accordance with the instructions as set forth in this document.  
This manual is not intended to be an exhaustive guide to table saw operational methods, use of jigs or  
after-market accessories, choice of stock, etc. Additional knowledge can be obtained from experienced  
users or trade articles. Whatever accepted methods are used, always make personal safety a priority.  
If there are questions or comments, please contact your local supplier or Walter Meier. Walter Meier can  
Retain this manual for future reference. If the machine transfers ownership, the manual should  
accompany it.  
Read and understand the entire contents of this manual before attempting  
assembly or operation! Failure to comply may cause serious injury!  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.0 Glossary  
Arbor: Metal shaft that connects the drive  
mechanism to the blade.  
Parallel: Position of the rip fence equal in  
distance at every point to the side face of the  
saw blade.  
Bevel Edge Cut: Tilt of the saw arbor and blade  
between 0° and 45° to perform an angled cutting  
operation.  
Perpendicular: 90° (right angle) intersection or  
position of the vertical and horizontal planes  
such as the position of the saw blade (vertical)  
to the table surface (horizontal).  
Blade Guard: Mechanism mounted over the  
saw blade to prevent accidental contact with the  
cutting edge.  
Push Board/Push Stick: An instrument used to  
safely push the workpiece through the cutting  
operation.  
Crosscut: Sawing operation in which the miter  
gauge is used to cut across the grain of the  
workpiece.  
Rabbet: A cutting operation that creates an  
L-shaped channel along the edge of the board.  
Dado Blade: Blade(s) used for cutting grooves  
and rabbets. A stacked dado set can be used for  
wider grooves.  
Rip Cut: A cut made along the grain of the  
workpiece.  
Dado Cut: Flat bottomed groove in the face of  
the workpiece made with a dado blade.  
Riving Knife: A metal plate fixed relative to the  
blade, which moves with the blade as cutting  
depth is adjusted. Thus, it maintains not only the  
kerf opening in the workpiece, but also the knife-  
to-blade distance. A low-profile riving knife is  
Featherboard: Device used to keep a board  
against the rip fence or table that allows the  
operator to keep hands away from saw blade.  
used when performing  
a
non-through cut  
Freehand: Moving the workpiece into the blade  
using only the hands, without a fixed positioning  
device. (This is a dangerous, unacceptable  
procedure – always use appropriate devices to  
feed the workpiece though the saw blade during  
cutting operations.)  
because it sits lower than the top edge of the  
blade.  
Splitter (Spreader): A stationary metal plate to  
which the blade guard is attached that maintains  
the kerf opening in the workpiece when  
performing a cutting operation.  
Kerf: The resulting cut or gap made by a saw  
blade.  
Standard Kerf: 1/8" gap made with a standard  
blade.  
Kickback: An event in which the workpiece is  
lifted up and thrown back toward an operator,  
caused when a workpiece binds on the saw  
blade or between the blade and rip fence (or  
other fixed object). To minimize or prevent injury  
from kickbacks, see the Operations section.  
Straightedge: A tool used to check that a  
surface is flat or parallel.  
Through Sawing: A sawing operation in which  
the workpiece thickness is completely sawn  
through. Proper blade height usually allows 1/8"  
of the top of blade to extend above the wood  
stock. Keep the blade guard down, the anti-  
kickback pawls down, and the riving knife in  
place over the blade.  
Miter Gauge: A component that controls the  
workpiece movement while performing  
crosscut of various angles.  
a
Non-Through Cut: A sawing operation that  
requires the removal of the blade guard and  
standard riving knife, resulting in a cut that does  
not protrude through the top of the workpiece  
(includes Dado and rabbet cuts).  
The blade guard and riving knife must be re-  
installed after performing a non-through cut to  
avoid accidental contact with the saw blade  
during operation.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.0 Features  
Figure 1  
7.0 Specifications  
Model number................................................................................................... ............................................... JPS-10TS  
Stock numbers: (Steel Wings) (Cast Iron Wings)  
Saw Unit only with Steel Wings.......................................................708490 ................................................................  
Saw Unit only with Cast Iron Wings ............................................................ ....................................................708491  
Saw with 30” Rails/Fence Kit........................................................ 708492K .................................................708494K  
Saw with 52” Rails/Fence Kit & Wood Ext. Table ........................ 708493K .................................................708495K  
Motor and electricals:  
Motor type ....................................................totally enclosed fan cooled, induction, capacitor start, with reset button  
Horsepower................................................................................................................................................... 1-3/4 HP  
Phase ................................................................................................................................................................. single  
Voltage ...............................................................................................................................115/230V (prewired 115V)  
Cycle ................................................................................................................................................................... 60Hz  
Listed FLA (full load amps)................................................................................................................................ 14/7 A  
Starting amps ....................................................................................................................................................... 84 A  
Running amps (no load) ......................................................................................................................................... 4 A  
Start capacitor ................................................................................................................................ 200MFD, 125VAC  
Run capacitor .......................................................................................................................................35μF, 300VAC  
Power transfer.....................................................................................................................................................v-belt  
On/off switch..............................................................................................................................................push button  
Motor speed ................................................................................................................................................3450 RPM  
Power cord length ................................................................................................................................... 6 ft. (183cm)  
Power plug installed ...............................................................................................................................................yes  
Recommended circuit and fuse/breaker size1 ...................................................................20A (115V), or 15A (230V)  
Sound emission................................................................................. 80 dB at 30” (762mm) from blade, without load  
1 subject to local/national electrical codes.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Arbor and blade:  
Blade included...................................................................................................................................... 40 Tooth, ATB  
Blade diameter ........................................................................................................................................10” (254mm)  
Arbor diameter.....................................................................................................................................5/8” (15.88mm)  
Arbor speed (RPM) ..............................................................................................................................................4000  
Arbor lock ...............................................................................................................................................................yes  
Maximum depth of cut at 90 degrees ....................................................................................................3-1/8” (79mm)  
Maximum depth of cut at 45 degrees ....................................................................................................2-1/8” (54mm)  
Maximum rip to right of blade ........................................................................................ 30” (52” with wood ext. table)  
Maximum rip to left of blade ....................................................................................................................12” (305mm)  
Dado maximum width........................................................................................................................13/16” (20.6mm)  
Dado maximum diameter ..........................................................................................................................8” (200mm)  
Blade height per one revolution of handwheel ......................................3/32” (2.3mm) for 90°; 1/16” (1.7mm) for 45°  
Blade tilt..............................................................................................................................................left, 0 to 45 deg.  
Materials:  
Main table...........................................................................................................................................ground cast iron  
Trunnion.........................................................................................................................................................cast iron  
Enclosed cabinet..................................................................................................................................................steel  
Legs......................................................................................................................................................................steel  
Extension wings ................................................................................................................................ steel or cast iron  
Table:  
Table dimensions ............................................................................................................20”L x 27”W (508 x 686mm)  
Table dimensions with wings.........................................................................................44”L x 27”W (1118 x 686mm)  
Table area in front of blade at maximum height ......................................................................................10” (259mm)  
Table height from floor, approximate.................................................................................................34-3/4” (883mm)  
Miter slot.......................................................................................................two T-slots, 3/4 ”W x 3/8”D (19 x 10mm)  
Edge bevel ........................................................................................................................................................... front  
Dimensions:  
Stand footprint...........................................................................................................29”L x 26-1/2”W (737 x 673mm)  
Overall dimensions of shipping carton (basic saw only)........................... 30”L x 29-3/4”W x 29”H (76x75.5x74.5cm)  
Overall dimensions, fully assembled, accessories mounted:  
with 30” rip...................................................................................... 60”L x 40”W x 41”H (1524 x 1016 x 1041mm)  
with 52” rip...................................................................................... 82”L x 40”W x 41”H (2083 x 1016 x 1041mm)  
Dust collection:  
Dust port outside diameter ........................................................................................................................4” (100mm)  
Minimum extraction volume required ............................................................................................350 CFM (18CMM)  
Weights:  
(Steel Wings)  
(Cast Iron Wings)  
Saw Only (Net/Shipping)...................................210/223 lb (95.5/101.5 kg) ....................250/263 lb (113.9/119.5 kg)  
Saw assembled with 30” Rail/Fence ...................................252 lb (114 kg) .....................................292 lb (132.5 kg)  
Saw assembled with 52” Rail/Fence ...................................302 lb (137 kg) ........................................342 lb (155 kg)  
The specifications in this manual were current at time of publication, but because of our policy of continuous  
improvement, Walter Meier (Manufacturing) Inc., reserves the right to change specifications at any time and without  
prior notice, without incurring obligations.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hardware Package (p/n JPS10TSR-HP)  
8.0 Setup and assembly  
Remove contents from all packets and sort. Use  
Figures 3 and 4 to help identify hardware.  
8.1 Shipping contents  
Carton contents (see Figure 2)  
1
1
4
8
2
8
Lock knob (HP-1)  
Bushing (HP-2)  
Knobs for dust hood (HP-3)  
M8x20 Hex cap screws (HP-4)  
M8x10 Hex cap screws (HP-5)  
M6x16 Hex cap screws (HP-6)  
NOTE: Some parts may have come pre-  
assembled to the table saw.  
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
1
Table saw (not shown)  
Blade (not shown)  
Extension wing – Left (A)  
Extension wing – Right (B)  
Dust hood (C)  
Legs (D)  
Feet (E)  
Miter gauge (F)  
Handwheel – large mounting hole (G)  
Handwheel – small mounting hole (H)  
Push stick (J)  
Guard assembly (K)  
Riving knife (L)  
Low profile riving knife (M)  
Owner’s manual (not shown)  
Warranty card (not shown)  
16 M6x12 Socket head button screws (HP-7)  
10 8mm Flat washers (HP-8)  
8
8
1
1
6mm Flat washers (HP-9)  
6mm Hex nuts (HP-10)  
M5x12 Socket head cap screw (HP-11)  
5mm Lock washer (HP-12)  
Figure 3  
Tools included for assembly  
1
1
1
1
1
23mm Combination wrench  
10-12mm Open end wrench  
11-13mm Open end wrench  
4mm Hex key  
2.5mm Hex key  
Note: other tools not provided may be required  
for assembly.  
Figure 4  
Note: Fence and rail assemblies, and wood  
extension tables and legs, are shipped in  
separate cartons.  
Figure 2  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
with the larger mounting hole, making sure  
to line up the flat side in the hole with the flat  
side on the shaft.  
Read and understand all  
assembly instructions before attempting  
assembly. Failure to comply may cause  
serious injury.  
2. Fasten in place with lock knob (HP-1).  
3. Slide the remaining handwheel (E) with the  
smaller mounting hole onto the shaft (F) on  
the right side of table saw, lining up the flat  
side in the hole with the flat side on the  
shaft.  
The main saw unit is heavy;  
use of an assistant is highly recommended  
when moving or turning it right side up.  
4. Secure handwheel with lock washer and  
Tools required for assembly:  
screw (HP-11/12), using 4mm hex key.  
4mm hex key  
10mm open-end wrench  
Rubber mallet (for wing adjustment)  
Cross point (Phillips) screwdriver  
8.2 Unpacking and cleanup  
1. Remove all contents from shipping carton.  
Keep saw table upside down (see Figure 5),  
and place a two-by-four or similar piece of  
wood under the rear of the saw – this will  
help when picking up the table again. Do not  
discard carton or packing material until saw  
is assembled and running satisfactorily.  
2. Inspect contents for shipping damage.  
Report damage, if any, to your distributor.  
3. Compare contents of shipping carton with  
the contents list in this manual. Report  
shortages, if any, to your distributor.  
8.3 Installing legs  
Referring to Figure 5:  
1. Install a foot (C) on the bottom of each leg,  
using two screws, washers and hex nuts  
(HP-6/9/10) for each foot. Hand tighten only.  
2. Mount four steel legs (A) to cabinet using  
sixteen button head screws (HP-7). Install all  
four screws first, then tighten with 4mm hex  
key.  
Figure 5  
NOTE: Remove right side motor cover for  
installing last leg screw. (Leave cover off  
until wings are installed.)  
3. Turn saw right side up and allow the feet to  
adjust to floor surface. Tighten hex nuts with  
10mm wrench.  
8.4 Handwheels  
Figure 6  
Referring to Figure 6:  
The JPS-10TS Table Saw is equipped with two  
handwheels which look identical except for the  
mounting holes, as follows:  
1. On front of table saw, slide bushing (HP-2)  
onto shaft (A) followed by handwheel (C)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
extension wing level with saw table. When  
extension wing is level with table, securely  
tighten each of the four screws.  
8.5 Extension wings  
Referring to Figure 7:  
4. Repeat steps 1 through 3 for opposite  
extension wing.  
Make sure mating surfaces are clean and free of  
burrs.  
5. Reinstall right side motor cover.  
1. Attach right extension wing (J) to saw table  
using four screws and washers (HP-4/8).  
Hand-tighten only at this time.  
8.7 Rails and fence  
2. Repeat for left side.  
To install front and rear rails and fence, consult  
manual M-708482 which accompanies your  
fence assembly, then proceed to section 8.9.  
8.8 Wood extension table  
To install the optional wood table, consult  
manual M-708482, which accompanies your  
fence assembly, then proceed to section 8.9.  
8.9 Switch bracket  
Referring to Figure 9:  
Use two screws and washers (HP-5/8) to secure  
switch bracket (M) to front rail.  
Figure 7  
8.6 Extension wing adjustment  
Referring to Figure 8:  
Level extension wing (J) to saw table using a  
straight edge (L). A metal straight edge is ideal,  
although a carefully jointed board may also be  
used, as shown.  
Figure 9  
8.10 Dust Hood  
Referring to Figure 10:  
Install dust hood at rear of cabinet, using four  
small lock knobs (HP-3). The dust port should  
be toward the bottom.  
Figure 8  
A dust collection system, with minimum capacity  
of 350 cubic feet per minute, should be  
connected to the port via a 4-inch diameter hose  
(not included). Note: Dryer vent hose is not  
acceptable for this purpose.  
1. Begin with the extension wings raised  
slightly higher than the main table. Tighten  
the four screws (13mm wrench) under the  
extension wing that secure it to the saw  
table. Tighten these just enough to hold the  
wing in place but loose enough to change  
the wing height by tapping on it.  
An extensive line of JET dust collectors is  
available – contact your dealer or visit our  
website for information.  
2. Lay straight edge across saw table and  
extension wing, extending out past edge of  
wing, as shown.  
3. Move straight edge to several places along  
the wing, as you continue to nudge the  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
be necessary. However, proper alignment is  
very important. Before operating table saw, read  
section 8.15 – Aligning Blade Guard and Riving  
Knife, to verify and follow the adjustment  
procedure if necessary.  
8.12 Anti-kickback pawls  
Referring to Figures 12.  
1. Push and hold the button (A) on the  
opposite side of the head to release the  
catch pin. Mount the pawl assembly straight  
down, in the location shown in Figure 12.  
Figure 10  
2. Pivot the head and push it downward  
(Figure 13) until there is an audible click.  
Make sure you hear the click to verify that  
pawl assembly is secure!  
8.11 Riving knife  
Referring to Figure 11:  
Figure 11  
1. Set saw blade to 90-degree (vertical)  
position and raise it all the way (refer to  
section 10.1 – Blade raising/tilt mechanism).  
Figure 12  
2. Remove table insert by rotating lever (shown  
at E, Figure 18) and lifting up insert using  
finger hole.  
Use care when working  
around an installed blade.  
3. Through the saw table opening, loosen hand  
knob (A, Figure 11) by rotating counter-  
clockwise. The floating clamp block (B) will  
move away from the fixed block (C), leaving  
a gap.  
4. Slide tabs of riving knife (D) into slot  
between the two blocks, all the way down  
onto mounting stud.  
5. Tighten the hand knob (A) to secure the  
riving knife.  
The clamping blocks (B/C, Figure 11) are  
adjusted at the factory and no further adjustment  
of blade guard and riving knife assembly should  
Figure 13  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Using the handwheels, raise the blade arbor  
fully and lock saw at zero degrees by  
tightening lock knob at center of handwheel.  
Referring to Figure 16:  
2. Press arbor lock button (E) and rotate arbor  
until you feel arbor lock engage. Continue  
pressing arbor lock button.  
3. Using the provided wrench, remove arbor  
nut (F) and outer flange (G). If replacing  
blade, remove old blade.  
4. Place blade (H) on arbor shaft (I) making  
sure that the teeth point down at the front of  
the saw. Replace flange (G) and arbor nut  
(F).  
5. Tighten arbor nut (F).  
Figure 14  
8.13 Blade guard  
Referring to Figure 14.  
1. Push up guard leaves (B) until they catch  
and hold on the peg (C).  
2. Lower blade guard assembly onto riving  
knife and push it backward to seat it.  
3. Tighten knob (D).  
4. Pull down guard leaves into position shown  
in Figure 15.  
5. Reverse procedure to remove guard.  
IMPORTANT: Knob (D) must be tightened  
before operating saw with guard in place.  
Figure 16  
Figure 15  
8.14 Blade installation/replacement  
When installing or changing  
blades, always disconnect saw from power  
source. Failure to comply may cause serious  
injury.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.17 Table insert  
8.15 Aligning blade guard and riving  
Referring to Figure 18:  
knife  
1. Remove blade guard and riving knife.  
2. Lower blade completely.  
Referring to Figure 17:  
1. Remove blade guard and hold anti-kickback  
pawls (J) away from table surface, or  
remove them.  
3. Place table insert (A) into opening with  
notched end (B) towards rear of table.  
2. Place an accurate straight edge (K) flush  
against saw blade (L) and riving knife (M).  
For proper alignment, blade and riving knife  
should be perfectly in line with the straight-  
edge.  
4. Adjust insert flush with table by turning four  
leveling setscrews (C) and using a straight  
edge (D) at different points over the insert. A  
2.5mm hex key is required to adjust the  
setscrews.  
If alignment is required:  
5. Turn lever (E) so that it catches the insert  
and holds it against table. If the lever needs  
adjustment, remove insert and rotate lever  
up or down until it will properly catch the  
insert.  
3. Move straight-edge aside, and through the  
opening locate four set screws (N) at the  
corners of the clamp block. See inset, Figure  
17 (riving knife removed for clarity).  
4. Rotate any of the four set screws as  
needed, to tilt the angle of the riving knife to  
achieve alignment.  
5. Check alignment by repeating steps 1 and 2.  
If necessary, repeat steps 3 and 4 until  
proper alignment is achieved.  
Figure 18  
8.18 Miter gauge  
Referring to Figure 19:  
Figure 17  
8.16 Low profile riving knife  
Figure 19  
A low profile riving knife is included with your  
saw. It mounts and adjusts in the same manner  
as the standard riving knife. The low profile  
riving knife sits just below top of blade and is  
used for making non-through cuts. The blade  
guard is not used with this knife, so extra  
precautions should be taken during operation.  
Operate miter gauge by loosening lock knob (A)  
and turning miter body (B) to desired angle.  
The pin (C) functions as an index stop. When  
pushed in, the body will stop at -45º, 90º or +45º  
when turned, as one of three screws (D) located  
underneath the miter body hits the pin.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
understood, or if in doubt as to whether the  
tool is properly grounded. Failure to comply  
may cause serious or fatal injury.  
You can adjust any play of the miter gauge in  
the table slot by tightening set screws (E).  
Calibration  
Use only 3-wire extension cords that have 3-  
prong grounding plugs and 3-pole receptacles  
that accept the tool's plug.  
If a miter angle at the -45º, 90º or +45º is not  
correct, the index stops can be adjusted by  
turning one of three adjustment screws (D), then  
locking the hex nut.  
Repair or replace damaged or worn cord  
immediately.  
Note: Always make test cuts. Do not rely solely  
2. Grounded, cord-connected tools intended for  
use on a supply circuit having a nominal rating  
less than 150 volts:  
on miter gauge indicator marks.  
9.0 Electrical connections  
This tool is intended for use on a circuit that has  
an outlet that looks like the one illustrated in A,  
Figure 20. An adapter, shown in B and C, may  
be used to connect this plug to a 2-pole  
receptacle as shown in B if a properly grounded  
outlet is not available. The temporary adapter  
should be used only until a properly grounded  
outlet can be installed by a qualified electrician.  
This adapter is not permitted in Canada. The  
green-colored rigid ear, lug, and the like,  
extending from the adapter must be connected  
to a permanent ground such as a properly  
grounded outlet box.  
The JPS-10TS table saw is rated at 115/230V  
power, and is pre-wired for 115 volt. The table  
saw comes with a plug designed for use on a  
circuit with a grounded outlet that looks like the  
one pictured in A, Figure 20.  
Before connecting to power source, be sure  
switch is in off position.  
It is recommended that the table saw, when  
operated on 115 volt power, be connected to a  
dedicated 20 amp circuit with a 20 amp circuit  
breaker or time-delay fuse marked “D”. When  
operated on 230 volt power, it is recommended  
that the table saw be connected to a dedicated  
15 amp circuit with a 15 amp circuit breaker or  
time-delay fuse marked “D”. Local codes take  
precedence over recommendations.  
3. Grounded, cord-connected tools intended for  
use on a supply circuit having a nominal rating  
between 150 - 250 volts, inclusive:  
This tool is intended for use on a circuit that has  
an outlet that looks like the one illustrated in D,  
Figure 20. The tool has a grounding plug that  
looks like the plug illustrated in D. Make sure the  
tool is connected to an outlet having the same  
configuration as the plug. No adapter is  
available or should be used with this tool. If the  
tool must be reconnected for use on a different  
type of electric circuit, the reconnection should  
be made by qualified service personnel; and  
after reconnection, the tool should comply with  
all local codes and ordinances.  
9.1 Grounding instructions  
1. All Grounded, Cord-connected Tools:  
In the event of a malfunction or breakdown,  
grounding provides a path of least resistance for  
electric current to reduce the risk of electric  
shock. This tool is equipped with an electric cord  
having an equipment-grounding conductor and a  
grounding plug. The plug must be plugged into a  
matching outlet that is properly installed and  
grounded in accordance with all local codes and  
ordinances.  
Do not modify the plug provided - if it will not fit  
the outlet, have the proper outlet installed by a  
qualified electrician.  
Improper connection of the equipment-  
grounding conductor can result in a risk of  
electric shock. The conductor with insulation  
having an outer surface that is green with or  
without yellow stripes is the equipment-  
grounding conductor. If repair or replacement of  
the electric cord or plug is necessary, do not  
connect the equipment-grounding conductor to a  
live terminal.  
Figure 20  
9.2 Voltage conversion  
Check with  
electrician or service personnel if the  
grounding instructions are not completely  
a
qualified  
To switch the incoming power leads for 230 volt  
operation, follow the wiring diagram on the  
inside cover of motor junction box. To access  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
junction box (A, Figure 21), tilt blade to 45  
degrees, and remove right side cover.  
shown in Figure 22. To safeguard your machine  
from unauthorized operation and accidental  
starting by young children, the use of a padlock  
(not included) is highly recommended. Place the  
key in a location that is inaccessible to children  
and others not qualified to use the tool.  
Figure 22  
Figure 21  
The plug on the end of the motor cord must be  
replaced with a UL/CSA listed plug rated for  
240V.  
10.0 Adjustments  
Disconnect saw from power  
source before making adjustments.  
9.3 Overload reset button  
If saw becomes overloaded and the motor shuts  
off, push the re-set button on motor junction box  
(B, Figure 21) to restart. If overloading happens  
frequently, consult the Troubleshooting section  
in this manual.  
10.1 Blade raising/tilt mechanism  
Never try to force the tilting  
mechanism past the 45º or 90º stops. This  
may cause the blade to go out of alignment.  
Referring to Figure 23:  
9.4 Extension cords  
To raise or lower blade, loosen lock knob (A)  
and turn handwheel (B) on front of saw until  
desired height is reached. Tighten lock knob.  
The blade should be adjusted about 1/8" above  
the top surface of the material being cut.  
USE PROPER EXTENSION CORD. Make sure  
your extension cord is in good condition. When  
using an extension cord, be sure to use one  
heavy enough to carry the current your product  
will draw. An undersized cord will cause a drop  
in line voltage resulting in loss of power and  
overheating. Table 1 shows correct size to use  
depending on cord length and nameplate  
ampere rating. If in doubt, use the next heavier  
gauge. The smaller the gauge number, the  
heavier the cord.  
To tilt blade, turn lock handle (C) counter-  
clockwise to loosen, turn handwheel (D) until  
desired angle is obtained, then tighten lock  
handle (C) clockwise.  
Ampere  
Rating  
Total length of  
cord in feet  
Volts  
120  
240  
25 50  
50 100 200  
100  
150  
300  
Not  
More  
Than  
More  
Than  
AWG  
00  
06  
10  
06  
10  
12  
18 16  
18 16  
16 16  
16  
14  
14  
12  
12  
14  
Not  
12  
16  
14 12  
Recommended  
Figure 23  
Extension Cord Recommendations  
Table 1  
10.2 Adjusting 45º and 90º positive  
stops  
9.5 On-off switch padlock  
1. Disconnect saw from power source.  
2. Raise blade to maximum height.  
The Table Saw is equipped with a push-button  
switch that will accept a safety padlock, as  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Set blade 90º to table by turning blade tilting  
handwheel (D, Figure 23) counterclockwise  
as far as it will go. Do not force beyond stop.  
9. Place a square (D, Figure 25) on the table  
and verify that blade (E, Figure 25) is at 45º  
to table. Make sure that the square is not  
touching a blade tooth.  
4. Place a square (A, Figure 24) on the table  
and verify that blade (B, Figure 24) is at 90º  
to table. Make sure that the square is not  
touching a blade tooth.  
Figure 25  
If adjustment is required:  
10. Back out the 45º adjust setscrew (H, Figure  
25) counter-clockwise one or two turns with  
4mm hex key (F, Figure 20).  
Figure 24  
If adjustment is required:  
11. Turn blade tilt handwheel until blade is  
exactly 45º.  
5. Back out the 90º adjust setscrew (G, Figure  
24) counterclockwise one or two turns with  
4mm hex key (C, Figure 24).  
12. Tighten the 45º adjust setscrew (H) until it  
stops, but do not force.  
6. Turn blade tilting handwheel until blade is  
exactly 90º.  
NOTE: You may also need to verify the position  
of the stop collar (K, Figure 25a), accessed  
through front opening of cabinet. If adjustment is  
required, loosen the set screws and position the  
stop collar. Retighten set screws.  
7. Tighten the 90º adjust setscrew (G) until it  
stops, but do not force.  
8. Set blade at 45º to table by turning the blade  
tilting handwheel clockwise (D, Figure 23) as  
far as it will go. Do not force beyond stop.  
NOTE: If establishing a firm 90° stop is still  
unsuccessful, you may need to adjust the end  
screw (J, Figure 24a) located on the tilting  
leadscrew. The end screw is accessed by  
removing plastic cap from hole on left side of  
cabinet.  
Figure 25a  
Verify that blade tilt pointer (Figure 26) properly  
indicates 45º or 0º (90º). If not, loosen screw  
and adjust until pointer indicates correctly.  
Figure 24a  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 26  
Figure 28  
10.3 Table to blade alignment  
6. Lower blade all the way down. Remove  
blade guard and riving knife and any loose  
items from table top.  
Refer to Figures 27 and 28.  
The table has been set square with blade by the  
manufacturer and no adjustment is necessary  
now. As the saw receives extensive use,  
however, table/blade squareness should be  
7. Turn saw upside down (place mat or blanket  
on floor to protect table surface).  
8. Loosen trunnion screws (item #71, section  
16.1.1), and nudge trunnion assembly  
according to the distance you noted.  
checked  
occasionally  
and corrected if  
necessary. Use the miter slot to do this:  
1. Disconnect saw from power source.  
2. Raise blade to maximum height.  
9. Retighten trunnion screws firmly.  
10. Turn saw right side up, and verify the  
alignment, angle pointer setting, fence  
setting, etc. Make any needed adjustments.  
3. Mark one tooth (A) with a grease pencil and  
position the tooth slightly above the top edge  
of table at the front.  
11.0 Operations  
(NOTE: The following Figures may or may not  
show your saw model, but procedures are the  
same.)  
Familiarize yourself with the location and  
operation of all controls and adjustments and the  
use of accessories such as miter gauge and rip  
fence.  
Kickbacks  
Serious injury can result from kickbacks which  
occur when a workpiece binds on the saw blade  
or binds between the blade and rip fence or  
other fixed object. This binding can cause work  
piece to lift up and be thrown toward the  
operator.  
Figure 27  
4. Raise the miter gauge slightly out of its slot  
to serve as a shoulder. Using a sliding  
square (B) against the side of the bar, slide  
the scale over until it touches the tip of the  
blade, and lock the scale in position. See  
Figure 27.  
Listed below are conditions which can cause  
kickbacks:  
ˆ
Confining the cutoff piece when  
crosscutting or ripping.  
ˆ
Releasing the workpiece before  
completing operation or not pushing work  
piece all the way past the saw blade.  
Not using the splitter/riving knife when  
ripping or not maintaining alignment of the  
splitter/riving knife with the saw blade.  
Using a dull saw blade.  
5. Rotate marked tooth (A) so that it is slightly  
above table top at the rear and, using the  
square as before, verify that the distance to  
the blade is the same. See Figure 28. If the  
distances are not the same, make a careful  
note of the difference.  
ˆ
ˆ
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ˆ
ˆ
Not maintaining alignment of the rip fence  
so that it tends to angle toward rather than  
away from the saw blade front to back.  
Applying feed force when ripping to the  
cutoff (free) section of the workpiece  
instead of the section between saw blade  
and fence.  
ˆ
Ripping wood that is twisted (not flat), or  
does not have a straight edge, or a twisted  
grain.  
To minimize or prevent injury from kickbacks:  
ˆ
ˆ
Avoid conditions listed above.  
Wear a safety face shield, goggles, or  
glasses.  
Figure 30  
ˆ
Do not use the miter gauge and rip fence  
in the same operation unless provision is  
made by use of a facing board on the  
fence so as to allow the cutoff section of  
the workpiece to come free before the next  
cut is started (See Figure 37).  
Never use the fence as a length stop when  
crosscutting. Do not hold or touch the free end  
or cutoff section of a workpiece. On through-  
sawing operations, the cutoff section must NOT  
be confined.  
ˆ
ˆ
As the machine receives use, the  
operation of the anti-kickback pawls should  
be checked periodically (Figure 29). If the  
pawls do not stop the reverse motion of a  
workpiece, resharpen all the points.  
Where possible, keep your face and body  
out of line with potential kickbacks  
including when starting or stopping the  
machine.  
Always keep your hands out of line of the saw  
blade and never reach back of the cutting blade  
with either hand to hold the workpiece.  
Bevel ripping cuts should always be made with  
the fence on the right side of saw blade so that  
the blade tilts away from the fence and  
minimizes the possibility of the work binding and  
the resulting kickback.  
Rip sawing  
Ripping is where the workpiece is fed with the  
grain into the saw blade using the fence as a  
guide and a positioning device to ensure the  
desired width of cut (Figure 31).  
Figure 29  
Dull, badly set, improper, or improperly filed  
cutting tools and cutting tools with gum or resin  
adhering to them can cause accidents. Never  
use a cracked saw blade. The use of a sharp,  
well maintained, and correct cutting tool for the  
operation will help avoid injuries.  
Support the work properly and hold it firmly  
against gauge or fence. Use a push stick or  
push block when ripping short, narrow (6" width  
or less), or thin work. Use a push block or miter  
gauge hold-down when dadoing or molding.  
Figure 31  
Before starting a ripping cut,  
verify that fence is clamped securely and  
aligned properly.  
For increased safety in crosscutting, use an  
auxiliary wood facing (Figure 30) attached to the  
miter gauge, using the slots or holes provided in  
the gauge.  
ˆ
Never rip freehand or use miter gauge in  
combination with the fence.  
Never rip workpieces shorter than the saw  
blade diameter.  
ˆ
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ˆ
Never reach behind the blade with either  
hand to hold down or remove the cutoff  
piece with the saw blade rotating.  
Always use blade guard, splitter/riving knife and  
anti-kickback pawls. Make sure splitter/riving  
knife is properly aligned. When wood is cut  
along the grain, the kerf tends to close and bind  
on the blade and kickbacks can occur.  
Figure 33  
Figure 32  
The rip fence (A, Fig. 32) should be set for the  
width of the cut (C, Fig. 32) by using the scale  
on the front rail, or by measuring the distance  
between blade (B) and fence (A). Stand out of  
line with saw blade and workpiece to avoid  
sawdust and splinters coming off the blade or a  
kickback, if one should occur.  
If the work piece does not have a straight edge,  
nail an auxiliary straight edged board on it to  
provide one against the fence. To cut properly,  
the board must make good contact with the  
table. If it is warped, turn the hollow side down.  
Do not attempt to cut boards with significant  
warp.  
Figure 34  
When ripping long boards, use a support at front  
of table (A, Figure 34), such as a roller stand,  
and a support or "tailman" (B) at the rear.  
Never use the rip fence beyond the point where  
the carriage is flush with the end of the rails.  
In ripping, use one hand to hold the board down  
against the fence or fixture, and the other to  
push it into the blade between blade and fence.  
If workpiece is narrower than 6" or shorter than  
12", use a push stick or push block to push it  
through between fence and blade (Figure 33).  
Never push in a location such that the pushing  
hand is in line with the blade. Move the hand  
serving as a hold-down a safe distance from  
blade as cut nears completion. For very narrow  
ripping where a push stick cannot be used, use  
a push block or auxiliary fence. Always push the  
workpiece completely past the blade at the end  
of a cut to minimize the possibility of a kickback.  
Have the blade extend about 1/8" above the top  
of the workpiece. Exposing the blade above this  
point can be hazardous.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Resawing  
Resawing is a ripping operation in which thick  
boards are cut into thinner ones. Narrow boards  
up to 3" can be resawn in one pass. Wider  
boards up to 6" must be resawn in two passes.  
In resawing wider boards, adjust the blade  
height so as to overlap the two cuts by 1/2" as  
shown in Figure 35. Too deep a first cut can  
result in binding and possible kickbacks on the  
second cut. Always use the same side of the  
board against the fence for both cuts.  
Figure 37  
Length stops should not be used on the free end  
of the workpiece in the cutoff area.  
Do not crosscut workpieces shorter than 6".  
Before starting a cut, be sure the miter gauge is  
securely clamped at the desired angle. Hold the  
workpiece firmly against the table and back  
against the miter gauge. Always use the saw  
guard and riving knife and make sure the riving  
knife is properly aligned.  
For 90 degree crosscutting, most operators  
prefer to use the left-hand miter gauge slot.  
When using it in this position, hold the workpiece  
against the gauge with the left hand and use the  
right hand to advance the workpiece. When  
using the right hand slot for miter and compound  
crosscutting so that the blade tilts away from the  
gauge, the hand positions are reversed.  
Figure 35  
Crosscutting  
Crosscutting is where the workpiece is fed cross  
grain into the saw blade using the miter gauge to  
support and position the workpiece (Figure 36).  
When using the miter gauge, the workpiece  
must be held firmly and advanced smoothly at a  
slow rate. If the workpiece is not held firmly, it  
can vibrate causing it to bind on the blade and  
dull the saw teeth.  
Figure 36  
Crosscutting should never be done freehand nor  
should the fence be used as an end stop unless  
an auxiliary block (A, Figure 37) is clamped to  
the front of the blade area such that the cutoff  
piece comes free of the block before cutting  
starts.  
Figure 38  
To improve the effectiveness of the miter gauge  
in crosscutting, some users mount an auxiliary  
wooden extension face (A, Figure 38) with a  
glued-on strip of sandpaper (B) to the miter  
gauge.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Provide auxiliary support for any workpiece  
extending beyond the table top with a tendency  
to sag and lift up off the table.  
Have the blade extend only 1/8" above the top of  
the workpiece. Exposing the blade above this  
point can be hazardous.  
Dado cutting – Dadoing is cutting a wide  
groove into a workpiece or cutting a rabbet  
along the edge of a workpiece. A dado insert  
(optional accessory, not provided) shown in  
Figure 41, is necessary for this type of  
operation.  
Have the blade extend about 1/8" above the top  
of the workpiece. Exposing the blade above this  
point can be hazardous.  
Bevel and miter operations  
Bevel cut – A bevel cut is a special type of  
operation where the saw blade is tilted at an  
angle less than 90 degrees to the table top  
(Figure 39). Operations are performed in the  
same manner as ripping or crosscutting, except  
the fence or miter gauge should be used on the  
right-hand side of the blade to provide added  
safety in avoiding a binding action between  
blade and table top. When beveling with the  
miter gauge, the workpiece must be held firmly  
to prevent creeping.  
Do not use the standard table  
insert for dadoing operations.  
Figure 41  
The process of cutting 1/8" to 13/16" grooves in  
workpieces is accomplished by the use of a  
stacked dado blade set or an adjustable type  
blade mounted on the saw arbor. By using  
various combinations of stacked dado blades, or  
properly setting the dial on an adjustable blade,  
an accurate width dado can be made. This is  
very useful for shelving, making joints, tenoning,  
etc. The guard, riving knife, and anti-kickback  
pawls supplied with the saw should be used for  
all cutting operations where they can be used.  
When performing operations where the guard  
cannot be used, as in some dadoing operations,  
alternative safety precautions should be taken.  
Figure 39  
Mitering – Crosscuts made at an angle to the  
edge of the workpiece are called miters  
(Figure 40). Set the miter gauge at the required  
angle, lock the miter gauge, and make the cut  
the same as a normal crosscut except the  
workpiece must be held extra firmly to prevent  
creeping.  
These include push sticks, feather boards, filler  
pieces, fixtures, jigs and any other appropriate  
device that can be utilized to keep operators’  
hands away from the blade. Upon completion of  
the operation requiring removal of the guard, the  
entire guard assembly must be placed back on  
the machine in its proper working order.  
Never use a dado head in a  
tilted position. Never operate the saw without  
the blade guard, riving knife and anti-  
kickback pawls for operations where they  
can be used.  
Figure 40  
Note: When making compound miters (with  
blade tilted) use the miter gauge in the right  
hand slot to provide more hand clearance and  
safety.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12.0 Safety devices  
Feather board  
The feather board (Figure 42) should be made  
of straight grain hardwood approximately 1" thick  
and 4" to 8" wide depending on the size of the  
machine. The length is developed in accordance  
with intended use. Feather boards can be  
fastened to the table or rip fence by use of  
C-clamps. Alternatively, drilled and tapped holes  
in the table top allow the use of wing nuts and  
washers as a method of clamping. If this method  
of fastening is used, provide slots in the feather  
board for adjustment. (The illustration shows a  
method of attaching and use of the feather  
board as a vertical comb. The horizontal  
application is essentially the same except that  
the attachment is to the table top.)  
Figure 43 – Filler Piece  
Push stick & push block  
The use of a push block or push stick provides  
an added level of safety for the operator. A push  
stick is included with your table saw, but you  
may wish to make others personalized for  
different cutting procedures. The templates in  
Figures 44 and 45 offer construction details.  
Figure 44 – Push Block Template  
Figure 42  
Filler piece  
A filler piece (Figure 43) is necessary for narrow  
ripping and permits the blade guard to remain on  
the machine. It also provides space for the safe  
use of a push stick.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13.0 Maintenance  
Always disconnect power to  
the machine before performing maintenance.  
Failure to do this may result in serious  
personal injury.  
Cleaning  
Clean the JPS-10TS according to the schedule  
below to ensure maximum performance.  
Note—The following maintenance schedule  
assumes the saw is being used every day.  
Daily:  
ˆ Wipe down the table surface and T-slots  
with a rust preventive.  
ˆ Clean pitch and resin from the saw blade.  
Weekly:  
ˆ Clean motor housing with compressed air.  
ˆ Wipe down fence rails with a dry silicon  
lubricant.  
Lubrication  
Lubricate the areas indicated below every 12  
months.  
ˆ Lubricate blade angling trunnions with 6 or  
7 drops of light machine oil.  
ˆ Lubricate the blade height trunnion with 6  
or 7 drops of light machine oil.  
ˆ Worm gears and threads should be  
lubricated with an automotive wheel  
bearing grease.  
Check all adjustments after lubricating.  
Miscellaneous  
Figure 45 – Push stick template  
Always be aware of the condition of your  
machine. Routinely check the condition of the  
following items and repair or replace as  
necessary:  
ˆ Mounting bolts  
ˆ Power switch  
ˆ Saw blade  
ˆ Blade guard  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14.0 Optional accessories  
These accessory items, purchased separately, can enhance the functionality of your table saw. Contact  
your dealer to order, or call Walter Meier at the phone number on the cover.  
# 708489 – Dado Insert for ProShop Saw with Riving Knife  
# 708119 – Universal Mobile Base, adjustable up to 36” x 36”  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15.0 Troubleshooting the JPS-10TS  
Symptom  
Possible Cause  
Correction  
Motor will not start  
Low voltage.  
Check power line for proper voltage.  
Open circuit in motor or loose  
connection.  
Inspect all lead connections on motor for  
loose or open connections.  
Motor will not start: fuses Short circuit in line cord or plug.  
or circuit breakers blow.  
Inspect cord or plug for damaged insulation  
and shorted wires.  
Short circuit in motor or loose  
connections.  
Inspect all connections on motor for loose or  
shorted terminals or worn insulation.  
Incorrect fuses or circuit breakers in  
power line.  
Install correct fuses or circuit breakers.  
Motor overheats.  
Motor overloaded.  
Reduce load on motor.  
Air circulation through the motor  
restricted.  
Clean motor fan with compressed air to  
restore normal air circulation.  
Motor stalls, resulting in Motor overloaded.  
blown fuses or tripped  
Reduce load on motor.  
Short circuit in motor or loose  
Inspect connections on motor for loose or  
shorted terminals or worn insulation.  
circuit.  
connections.  
Low voltage.  
Correct the low voltage conditions.  
Incorrect fuses or circuit breakers in  
power line.  
Install correct fuses or circuit breakers.  
Machine slows when  
operating.  
Applying too much pressure to  
workpiece.  
Feed workpiece more slowly.  
Belt loose.  
Tighten belt.  
Loud, repetitive noise  
coming from machine.  
Pulley setscrews or keys are missing  
or loose.  
Inspect keys and setscrews. Replace or  
tighten if necessary.  
Motor fan is hitting the cover.  
Tighten fan or shim cover.  
V-belt is defective.  
Replace V-belt.  
Blade not square with  
miter slot, or fence not  
square to blade.  
Blade is warped.  
Replace saw blade.  
Table top not parallel to blade.  
Fence not parallel to blade.  
Adjust table parallel to blade.  
Adjust fence parallel to blade.  
Adjust 90 degree stop.  
Blade does not reach 90 90 degree stop is out of adjustment.  
degrees.  
Pointer bracket is hitting before the  
blade reaches 90 degrees.  
File down the right side of the pointer  
bracket until the blade can reach 90  
degrees.  
Table 2  
16.0 Replacement Parts  
Replacement parts are listed on the following pages. To order parts or reach our service department, call  
1-800-274-6848 Monday through Friday (see our website for business hours, www.waltermeier.com).  
Having the Model Number and Serial Number of your machine available when you call will allow us to  
serve you quickly and accurately.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.1.1 Motor and Trunnion – Exploded View  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.1.2 Motor and Trunnion – Parts List  
Index No Part No  
Description  
Size  
Qty  
1.............. VB-A31 ....................... V-Belt ..........................................................A-31...........................1  
2.............. JPS10TSR-102............ Belt .............................................................125J-6 .......................1  
3.............. TS-1523031 ................ Socket Set Screw.........................................M6 -1.0Px10...............2  
4.............. JPS10TS-351.............. Strain Relief .................................................SB8R-3......................2  
5.............. JPS10TSR-105............ Pulley ............................................................................................1  
6.............. JPS10TSR-106............ Washer..........................................................................................1  
7.............. BB-6202VV ................. Ball Bearing .................................................6202-2NSE ................2  
8.............. JPS10TSR-108............ Hook .............................................................................................1  
9.............. JWTS10-109 ............... Retaining Ring, External. ..............................STW-15 .....................2  
10............ JPS10TSR-110............ Pulley ............................................................................................1  
11............ BB-6002VV ................. Ball Bearing .................................................6002-2NSE ................2  
12............ TS-1490011 ................ Hex Cap Screw............................................M8-1.25Px12..............1  
13............ JPS10TSR-113............ Shaft .............................................................................................1  
14............ JPS10TSR-114............ Bearing Arm...................................................................................1  
15............ JPS10TSR-115............ Arbor.............................................................................................1  
16............ TS-1504101 ................ Socket Head Cap Screw...............................M8-1.25Px50..............1  
17............ TS-1541041 ................ Nylon Lock Hex Nut......................................M10...........................1  
18............ TS-1550071 ................ Flat Washer .................................................M10...........................1  
19............ TS-1550061 ................ Flat Washer .................................................M8.............................9  
20............ TS-1504041 ................ Hex Cap Screw............................................M8-1.25Px20..............4  
21............ TS-2361081 ................ Lock Washer................................................M8.............................8  
22............ JPS10TSR-122............ Bushing .........................................................................................1  
23............ JPS10TSR-123............ Center Trunnion.............................................................................1  
24............ JWTS10-124 ............... Hex Flange Bolt ...........................................M6x40........................1  
25............ JWTS10-125 ............... Spring ...........................................................................................1  
26............ TS-1550041 ................ Flat Washer .................................................M6.............................6  
27............ TS-1482041 ................ Hex Cap Screw............................................M6-1.0Px20................3  
28............ JPS10TSR-128............ Fixing Plate....................................................................................1  
29............ TS-2286121 ................ Phillips Flat Head Machine Screw .................M6-1.0Px12................4  
30............ TS-2210801 ................ Hex Cap Screw............................................M10x80......................1  
31............ JPS10TSR-131............ Blade...........................................................10”x5/8”x40T..............1  
32............ JWTS10-132 ............... Flange...........................................................................................1  
33............ JWTS10-133 ............... Arbor Nut.....................................................5/8”-12.......................1  
34............ JETLOGO-1................ JET Logo Plate ..............................................................................1  
35............ TS-1522011 ................ Socket Set Screw.........................................M5x6 .........................2  
36............ JPS10TS-136.............. Fixing Ring ....................................................................................1  
37............ JPS10TS-137.............. Spring Pin....................................................Ø4x18........................1  
38............ JWTS10-138 ............... E-Clip ..........................................................ETW-8 .......................1  
39............ JPS10TSR-139............ Bolt ...............................................................................................1  
40............ JWTS10-140 ............... Handle...........................................................................................1  
41............ JWTS10-141 ............... Spring ...........................................................................................1  
42............ JPS10TSR-141............ Retaining Ring .............................................RTW-24 .....................1  
43............ JWTS10-143 ............... Guide Shaft ...................................................................................1  
44............ JPS10-144 .................. Knob .............................................................................................1  
................ JPS10TS-FHA............. Front Hand Wheel Assembly (#45 thru #48).....................................1  
45............ JWTS10-145 ............... Handle Cap ...................................................................................2  
46............ JWTS10-146 ............... Handle...........................................................................................2  
47............ JWTS10-147 ............... Shaft .............................................................................................2  
48............ JPS10TS-148.............. Hand Wheel...................................................................................1  
49............ JPS10TSR-149............ Bushing ........................................................................................1  
50............ TS-1502031 ................ Socket Head Cap Screw...............................M5x12........................3  
51............ JWTS10-151 ............... Plate .............................................................................................1  
52............ JWTS10-152 ............... E-Clip ..........................................................ETW-12 .....................2  
53............ JPS10TSR-153............ Shaft .............................................................................................1  
54............ JWTS10-154 ............... O-Ring.........................................................P12............................2  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index No Part No  
Description  
Size  
Qty  
55............ JWTS10-155 ............... Wave Washer ..............................................WW-16 ......................1  
56............ LM000636................... Warning Label................................................................................1  
57............ JPS10TSR-157............ Angle Scale ...................................................................................1  
58............ TS-1541011 ................ Nylon Lock Hex Nut......................................M5.............................2  
59............ JWTS10-159 ............... Collar ............................................................................................1  
60............ JPS10TSR-160............ Support Bracket .............................................................................1  
61............ TS-2284082 ................ Phillips Pan Head Machine Screw .................M4x8 .........................1  
62............ JPS10TS-162.............. Pointer...........................................................................................1  
63............ JPS10TSR-163............ Bracket..........................................................................................1  
64............ TS-1550031 ................ Flat Washer .................................................M5.............................2  
65............ TS-1533042 ................ Phillips Pan Head Machine Screw .................M5x12........................4  
66............ 990805........................ Self Tapping Screw ......................................M4x10........................4  
67............ JPS10TS-167.............. Shaft .............................................................................................1  
................ JPS10TS-SHA............. Side Hand Wheel Assembly (#68, #45 thru #47) ..............................1  
68............ JPS10TS-168.............. Hand Wheel...................................................................................1  
69............ TS-1551031 ................ Lock Washer ...............................................M5.............................2  
70............ TS-1502031 ................ Socket Head Cap Screw ..............................M5x12........................2  
71............ TS-1490041 ................ Hex Cap Screw............................................M8x25........................4  
72............ TS-1540061 ................ Hex Nut .......................................................M8.............................4  
73............ JPS10TSR-173............ Front & Rear Trunnion....................................................................2  
74............ JPS10TSR-174............ Motor………………………………………….1-3/4HP, 1Ph, 115/230V ..1  
................ JPS10TSR -174MF...... Motor Fan (not shown)....................................................................1  
................ JPS10TSR-174MFC .... Motor Fan Cover (not shown)..........................................................1  
................ JPS10TSR -174CS ...... Centrifugal Switch (not shown)........................................................1  
................ JPS10TSR -174SCC.... Starting Capacitor Cover (not shown) ..............................................1  
................ JPS10TSR-174RCC .... Running Capacitor Cover (not shown) .............................................1  
................ JPS10TSR-174SC....... Starting Capacitor (not shown) ......................200MFD, 125VAC.......1  
................ JPS10TSR-174RC....... Running Capacitor (not shown) .....................35μF, 300VAC............1  
................ JPS10TSR-174JB........ Junction Box (not shown)................................................................1  
................ JPS10TSR-174JBC ..... Junction Box Cover (not shown)......................................................1  
................ JPS10TS-174OL.......... Overload........................................................................................1  
................ JPS10TSR-174DC....... Dust Cover ....................................................................................1  
75............ JPS10TSR-175............ Pulley ............................................................................................1  
76............ TS-1523041 ................ Socket Set Screw.........................................M6x12........................2  
77............ JPS10TSR-177............ Key .............................................................5x5x22.......................1  
78............ JPS10TSR-178............ Motor Wire.....................................................................................1  
79............ JBOS5-106.................. Open end Wrench .......................................#10 - #12 ...................1  
80............ JPS10TSR-180............ Blade Open End Wrench ..............................#23............................1  
81............ JPS10TS-181.............. Motor Cord Clamp..........................................................................2  
82............ JPS10TS-182.............. Turning Ball ...................................................................................1  
83............ TS-1521011 ................ Socket Set Screw.........................................M4x4 .........................2  
84............ JPS10TS-184.............. Stop Collar.....................................................................................1  
85............ JPS10TS-185.............. Key .............................................................5x5x18.......................2  
86............ TS-1532042 ................ Phillips Pan Head Machine Screw .................M4x12........................2  
87............ TS-1540021 ................ Hex Nut .......................................................M4.............................3  
88............ JPS10TSR-188............ Plate .............................................................................................1  
89............ JPS10TSR-189............ Extension Plate..............................................................................1  
90............ JPS10TSR-190............ Bar................................................................................................1  
91............ JPS10TSR-191............ Washer..........................................................................................1  
92............ TS-1481031 ................ Hex Cap Screw............................................M5-0.8x12..................1  
93............ TS-1541021 ................ Nylon Lock Hex Nut......................................M6-1.0P.....................3  
94............ JPS10TSR-194............ Riving Knife Clamp Base ................................................................1  
95............ JPS10TSR-195............ Spring ...........................................................................................1  
96............ TS-1504021 ................ Socket Head Cap Screw...............................M8-1.25Px12..............2  
97............ JPS10TSR-197............ Bolt ...............................................................................................1  
98............ JPS10TSR-198............ Riving Knife Clamp Plate ................................................................1  
99............ JPS10TSR-199............ Nylon Set Screw ..........................................M6-1.0Px8 .................4  
100.......... TS-1533052 ................ Phillips Pan Head Machine Screw .................M5-0.8Px16................2  
101.......... JPS10TSR-101............ Lock Knob .....................................................................................1  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index No Part No  
Description  
Size  
Qty  
102.......... TS-2245122 ................ Socket Head Button Screw ...........................M5-0.8Px12................1  
103.......... JPS10TSR-103............ Push Block ....................................................................................1  
104.......... JPS10TSR-104............ Open End Wrench (not shown) .....................#11 - #13 ...................1  
105.......... JPS10TSR-105............ Angle Wrench (not shown)............................2.5mm .......................1  
106.......... TS-152705 .................. Angle Wrench (not shown)............................4mm ..........................1  
107.......... JPS10TSR-107............ Nylon Socket Head Cap Screw .....................M6x15........................1  
................ STRIPE-1-3/4.............. JET Stripe (not shown) .................................1-3/4” w............... per ft.  
................ JPS10TSR-HP............. Hardware Package (see section 8.1 for included items)....................1  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.2.1 Table and Cabinet – Exploded View  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.2.2 Table and Cabinet – Parts List  
Index No Part No  
Description  
Size  
Qty  
1.............. JPS10TSR-301........Table .................................................................................................1  
2.............. JPS10TS-302..........Left Steel Extension Wing ...................................................................1  
3.............. JPS10TS-303..........Right Steel Extension Wing .................................................................1  
4.............. TS-2361081 ............Lock Washer ....................................................M8.............................3  
5.............. TS-1524051 ............Socket Set Screw .............................................M8x20........................2  
................ JPS10TSR-TIA........Table Insert Assembly (#6 thru #8) ......................................................1  
6.............. JPS10TSR-306........Lock Knob..........................................................................................1  
7.............. TS-1522041 ............Socket Set Screw .............................................M5-0.8Px12................4  
8.............. JPS10TSR-308........Table Insert ........................................................................................1  
9.............. TS-1490031 ............Hex Cap Screw ................................................M8x20........................8  
10............ TS-1550061 ............Flat Washer .....................................................M8.............................8  
11............ JPS10TS-311..........Cover.................................................................................................1  
12............ TS-1532032 ............Phillips Pan Head Machine Screw......................M4x10........................4  
13............ JPS10TSR-313........Cabinet ..............................................................................................1  
14............ TS-1550061 ............Flat Washer......................................................M8.............................3  
15............ TS-1490031 ............Hex Cap Screw ................................................M8x20........................3  
16............ JPS10TS-342..........STOP Switch Paddle ..........................................................................1  
17............ JPS10TS-343..........Main Switch w/ Face Plate ..................................................................1  
18............ JPS10TS-344..........Switch Plate .......................................................................................1  
19............ JPS10TS-345..........External Tooth Lock Washer..............................M4.............................2  
20............ TS-2171012 ............Phillips Pan Head Machine Screw......................M4x6 .........................2  
21............ JPS10TS-347..........Switch Box.........................................................................................1  
22............ JPS10TS-348..........Power Cord........................................................................................1  
23............ TS-1490011 ............Hex Cap Screw ................................................M8x10........................2  
24............ TS-1550061 ............Flat Washer......................................................M8.............................2  
25............ JPS10TS-351..........Strain Relief .....................................................SBRS-3......................3  
26............ TS-2284302 ............Phillips Pan Head Machine Screw......................M4x30........................2  
................ JPS10TS-MG ..........Miter Gauge Assembly (#27 thru #41) ..................................................1  
27............ JPS10TS-327..........Handle ...............................................................................................1  
28............ TS-0680041 ............Flat Washer......................................................3/8”............................1  
29............ JWTS10-329 ...........Miter Gauge Body...............................................................................1  
30............ TS-2284202 ............Phillips Pan Head Machine Screw......................M4x20........................3  
31............ TS-1540021 ............Hex Nut............................................................M4.............................3  
32............ TS-1533032 ............Phillips Pan Head Machine Screw......................M5x10........................3  
33............ JWTS10-333 ...........Pointer ...............................................................................................1  
34............ JWTS10-334 ...........Bracket ..............................................................................................1  
35............ JWTS10-335 ...........Stop Pin.............................................................................................1  
36............ JWTS10-336 ...........Screw ................................................................................................1  
37............ JPS10TS-337..........Miter Bar............................................................................................1  
38............ JWTS10-338 ...........Guide Washer ....................................................................................1  
39............ JWTS10-339 ...........Flat Head Screw...............................................M6x8 .........................1  
40............ JPS10TS-340..........Scale .................................................................................................1  
41............ TS-0270011 ............Socket Set Screw .............................................5/16”-18x1/4”..............2  
42............ JPS10TS-357..........Lock Knob..........................................................................................4  
43............ JPS10TS-358..........Dust Chute Cover ...............................................................................1  
44............ JPS10TSR-344........Lock Plunger ......................................................................................1  
45............ JPS10TS-360..........Spring................................................................................................1  
45............ JPS10TS-361..........E-Clip...............................................................ETW-7 .......................1  
47............ JPS10TSR-347........Low Profile Riving Knife ......................................................................1  
................ JPS10TSR-BGA ......Blade Guard Assembly (#48 thru #76)..................................................1  
................ JPS10TSR-UGA......Upper Guard Assembly (#48 thru #61,74,75)........................................1  
48............ JPS10TSR-348........Left Side outer Blade Guard ................................................................1  
49............ TS-1541011 ............Nylon Lock Hex Nut ..........................................M5.............................4  
50............ JPS10TSR-350........Flat Head Screw...............................................M5-0.8Px15................4  
51............ JPS10TSR-351........Left Side Inner Blade Guard ................................................................1  
52............ JPS10TSR-352........Shaft..................................................................................................1  
53............ JPS10TSR-353........Pan Head Screw...............................................M5-0.8Px6 .................4  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index No Part No  
Description  
Size  
Qty  
54............ JPS10TSR-354........Lock Knob..........................................................................................1  
55............ JPS10TSR-355........Support Arm.......................................................................................1  
56............ JPS10TSR-356........Left Fixing Bracket ..............................................................................2  
57............ JPS10TSR-357........Right Fixing Bracket............................................................................2  
58............ TS-1532032 ............Phillips Pan Head Machine Screw......................M4-0.7Px10................2  
59............ JPS10TSR-359........Lock Pin.............................................................................................2  
60............ JPS10TSR-360........Right Side Inner Blade Guard ..............................................................1  
61............ JPS10TSR-361........Right Side Outer Blade Guard .............................................................1  
................ JPS10TSR-AKPA ....Anti-Kickback Pawl Assembly (#62 thru #72,76) ...................................1  
62............ TS-1541011 ............Nylon Lock Hex Nut ..........................................M5-0.8P.....................1  
63............ JPS10TSR-363........Left Side Anti-kickback Pawl................................................................1  
64............ JPS10TSR-364........Left Side Spring..................................................................................1  
65............ JPS10TSR-365........Anti-Kickback Pawl Bracket .................................................................1  
66............ JPS10TSR-366........Lock Pin.............................................................................................1  
67............ JPS10TSR-367........Lock Shaft..........................................................................................1  
68............ JPS10TSR-368........Spring................................................................................................1  
69............ JPS10TS-361..........E-Clip...............................................................ETW-7 .......................1  
70............ JPS10TSR-370........Right Side Spring................................................................................1  
71............ JPS10TSR-371........Right Side Anti-kickback Pawl .............................................................1  
72............ TS-2285302 ............Phillips Pan Head Machine Screw......................M5-0.8Px30................1  
73............ JPS10TSR-373........Riving Knife........................................................................................1  
74............ JPS10TSR-374........O-Ring .............................................................P3..............................4  
75............ JPS10TSR-375........Warning Label ....................................................................................1  
76............ TS-1550031 ............Flat Washer......................................................M5.............................2  
77............ JPS10TSR-377........Cap ...................................................................................................1  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.3.1 Stand Assembly – Exploded View  
16.3.2 Stand Assembly – Parts List  
Index No Part No  
Description  
Size  
Qty  
1.............. TS-2246122 ............Socket Head Button Screw................................M6x12......................16  
2.............. JPS10TSR-402........Leg....................................................................................................4  
3.............. TS-1482031 ............Hex Cap Screw ................................................M6x16........................8  
4.............. TS-2311061 ............Hex Nut............................................................M6.............................8  
5.............. TS-1550041 ............Flat Washer......................................................M6.............................8  
6.............. JPS10TS-406..........Foot...................................................................................................4  
................ JPS10TS-SHP.........Stand Hardware Package (#1,3,4,5) ......................................................  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16.4.1 Cast Iron Wings – Exploded View  
16.4.2 Cast Iron Wings – Parts List  
Index No. Part No.  
Description  
Size  
Qty  
1.............. JPS10TS-501..........Cast Iron Wing....................................................................................2  
2.............. TS-1490031 ............Hex Cap Screw ................................................M8x20........................8  
3.............. TS-1550061 ............Flat Washer .....................................................M8.............................8  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17.1 Electrical Connections – 115V  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17.2 Electrical Connections – 230V  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WALTER MEIER (Manufacturing) Inc.  
427 New Sanford Road  
LaVergne, Tennessee 37086  
Phone: 800-274-6848  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer Dryer SIXL 125 S User Manual
Ingersoll Rand Impact Driver WG068A F4 User Manual
JBL Car Speaker P 422 User Manual
JVC Car Stereo System GET0143 001A User Manual
JVC CD Player GET0321 001A User Manual
JVC DVD Player XV 501BK User Manual
Kenmore Range 7907131 User Manual
Keystone Computer Keyboard Computer Keyboard User Manual
KitchenAid Ice Maker KUIS155HBL0 User Manual
Kramer Electronics Water Pump fc 42 User Manual