OWNER'S MANUAL
DC-1200A Dust Collector
JET EQUIPMENT & TOOLS, INC.
A WMH Company
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
Phone:253-351-6000
Fax: 1-800-274-6840
M-708634 04/01
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
1.
2.
Read and understand the entire contents of this manual before attempting assembly or
operation. Do not use this machine until proper training and knowledge has been obtained.
Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before
servicing.
3.
4.
5.
6.
Do not use outdoors or on wet surfaces.
Do not allow to be used as a toy. Close attention is necessary when used near children.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If Dust Collector is not working as it should, has been
dropped, damaged, left outdoor, or dropped in water, return it to a service center.
7.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run Dust Collector over cord. Keep cord away from heated surfaces.
8.
9.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or Dust Collector with wet hands.
10. Do not put any objects into the openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all parts of body away from opening and moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
13. Do not use without dust bag and/or filters in place.
14. Turn off all controls before unplugging.
15. Use extra care when cleaning on stairs.
16. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they
may be present.
17. Do not operate without hose connected to the hose inlet. Hazardous moving parts inside. Unplug
before removing hose inlet or inlet guard.
18. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
Crystalline silica from bricks and cement and other masonry products, and
Arsenic and chromium from chemically-treated lumber.
19. Your risk from those exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specifically designed to filter out microscopic
particles
20. Do not operate tool while under the influence of drugs, alcohol or any medication.
21. Make sure the extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. An undersize cord will cause a drop
in the line voltage resulting in loss of power and overheating. The table below shows the correct
size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller gauge number, the heavier the cord.
Cord Length
Cord Gauge
16 AWG
25’
50’
16 AWG
100’
150’
14 AWG
12 AWG
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
DC-1200A-1
DC-1200A-3
Stock Number.................................................... 708634 ............................................................... 708635
Blower Wheel Diameter..................................... 12".............................................................................12”
Sound Rating at 3 feet....................................... 80-85 db ........................................................... 80-85 db
Hose Diameter................................................... 4" & 6” ................................................................. 4” & 6”
Air Flow (CFM) .................................................. 1,200 ..................................................................... 1,200
Velocity at 4” (FPM)........................................... 13,745 ................................................................. 13,745
Static Pressure (inch of water)........................... 11.44 ..................................................................... 11.44
Bag Diameter .................................................... 20".............................................................................20"
Bag Length........................................................ 31-1/2”.................................................................31-1/2”
Collector Bag Capacity (cu. ft.) .......................... 5.6.............................................................................5.6
Overall Dimensions 30 Micron.......................... 37"L x 28"W x 79"H.........................37"L x 28"W x 79"H
Overall Dimensions 5 Micron............................ 37"L x 28"W x 96"H.........................37"L x 28"W x 96"H
Motor (TEFC) .................................................... 2 HP, 1Ph 230V only....................2 HP, 3Ph 230V/460V
.......................................................................... ...............................................................Prewired 230V
Net Weight (approx.) ......................................... 108 lbs................................................................108 lbs.
Table of Contents
Page
Warranty .................................................................................................................................................2
Warnings.................................................................................................................................................3
Grounding Instructions.............................................................................................................................4
Specifications..........................................................................................................................................4
Table of Contents ....................................................................................................................................4
Unpacking DC-1200A ..............................................................................................................................5
Contents of Shipping Carton....................................................................................................................5
Tools Required for Assembly...................................................................................................................5
Assembly..............................................................................................................................................6-8
Electrical Connections .............................................................................................................................8
Turning the Machine On & Off .................................................................................................................8
Maintenance............................................................................................................................................9
Parts Breakdown and Parts List ........................................................................................................10-11
Wiring Diagrams....................................................................................................................................12
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the dust collector!
Failure to comply may cause serious injury!
Unpacking
1. Finish removing all contents from the
shipping carton.
2. Report any damage to your distributor.
3. Do not discard any shipping material until
after the dust collector has been assembled
and is running properly.
Contents of the Shipping Carton
1
1
1
1
1
1
1
1
1
1
2
1
4
1
3
1
Bag Hanger
Base
Plastic Cover
Hanger Bracket
Hose
Owner's Manual
Warranty Card
Motor/Fan Assembly
Collector Bag
Filter Bag
Hose Clamps
Retainer Strap
Casters
Inlet Cover & Hose Inlet
Support Legs
Bag of Assembly Hardware
Tools Required for Assembly
2. 1/2” or 13mm Wrenches or sockets
1. 9/16” or 14mm Wrench or socket
1. #2 Cross Point Screw Driver
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
1. Install four casters to the under side of the
base as pictured in Fig. 1. Thread the hex
nut (B, Fig. 1) onto the caster shaft. Then
slide the lock washer (A, Fig. 1) over the
caster shaft. Thread the caster shaft into
the threaded hole on the underside of the
base, turn until snug. Tighten the nut (B,
Fig. 1) against the base with a 9/16” or
14mm wrench. This will give the caster
proper clearance.
2. Place the base with casters on the ground.
Attach the motor and fan assembly (A, Fig.
2) to the base using four M8 x 16 hex cap
bolts, four M8 flat washers (B, Fig. 2), and a
1/2" or 13mm wrench.
WARNING
The dust collector must be disconnected
from the power source during assembly.
Failure to comply may result in serious
injury!
3. Attach inlet guard (A, Fig. 3) to fan housing
using eight M5 x 12 pan head screws (B,
Fig. 3). Press the inlet ports onto the inlet
guard until it snaps into place.
WARNING
To reduce the risk of injury from moving
parts, always keep inlet ports covered with
the caps provided, if they are not
connected to a flexible hose. Failure to
comply may result in serious injury!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach three support brackets (A, Fig. 4) to
the base using six M8 x 16 hex cap bolts
and six M8 flat washers (B, Fig. 4). Hand
tighten only at this time.
5. Install the housing (A, Fig. 5) to two support
brackets using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts
(B, Fig.5). Be sure hose opening faces fan
housing. Before attaching third support
bracket place the hanger bracket (C, Fig.5)
between the support bracket and the
housing. Tighten all nuts and bolts at this
time with a 1/2" or 13mm wrench.
6. Attach the hose (A, Fig. 6) between the fan
housing and the collector housing with two
clamps (B, Fig. 6). Tighten the clamps to
secure the hose.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Slide the bag hanger hook (A, Fig. 7)
through the top loop of the filter bag. Insert
the hanger into the hanger bracket. Thread
the retainer strap (B, Fig. 7) through the
loops on the filter bag (C, Fig.7), and fasten
to the collector housing. The retainer strap
should be tight enough to provide a good
seal.
8. Insert the ring (A, Fig. 8) of the collector bag
into the bottom of the housing at an angle.
Pull down on the bag to make sure it “seats”
in the housing.
Electrical Connections
WARNING
All electrical connections must be done by a
qualified electrician. All adjustments or
repairs must be done with the dust collector
disconnected from the power source,
unplugged. Failure to comply may result in
serious injury!
The DC-1200A-1 dust collector is rated at 230V
Only. The DC-1200A-3 is rated at 3 Phase
230V/460V, Prewired 230V.
If you want to run the DC-1200A-3 on 460V refer
to the wiring diagram found on the inside of the
switch box cover.
Before hooking up to the power source, make
sure that the switch is in the off position.
Turning the Machine On & Off
Before hooking up to the power source, make
sure that the switch is in the off position.
The dust collector can be turned on by pressing
the start button found on the motor. Press the
stop button to turn off the dust collector.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer
vent hose is not acceptable for this purpose.
Contact your nearest JET distributor for the full
line of JET Dust Collector Hoses and
Accessories. Customize your installation and
obtain maximum performance with JET's dust
hoods, hoses, clamps, fittings, and blast gates.
Accessories.
Maintenance
WARNING
Never perform maintenace on this machine
before turning switch off and removing plug
from power source, unplug.
Failure to comply may cause serious injury!
Cleaning the Filter Bag
Motor
CAUTION
Wearing a particle mask/respirator for
protection against fine dust particles during
cleaning is highly recommended.
Make frequent inspections of the motor fan and
blow out (with low pressure air hose) or vacuum
any accumulation of foreign material in order to
maintain normal motor ventilation.
During first use and after cleaning, the filter bag
may allow some dust to escape. This is normal
and will stop after a short period of time.
Clean both the filter and collector bags
frequently to keep the collector's performance at
its optimum. To clean:
1. Disconnect the machine from the power
source.
2. Unhook the filter bag from the hanger and
shake the bag so that the majority of the
dust falls into the collector bag.
3. Loosen the retaining strap, and remove the
filter bag from the housing.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and re-attach to the
housing using the retainer strap to secure.
Removing the Collector Bag
1. Disconnect the machine from the power
source, unplug.
2. Remove the collector bag by pushing the
ring of the collector bag upwards and pulling
the bag out at an angle.
3. Empty the contents into an appropriate
container.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and insert into the
housing.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the DC-1200A
Index Part
No. No.
Description
Size
Qty.
1..........411035W ..................... Impeller Housing.................................... ...............................................1
2..........411026W ..................... Motor Bracket........................................ ...............................................1
3..........998621......................... Strain Relief........................................... ...............................................1
4..........MA411003.................... Motor.....................................................2 HP, 1Ph ...............................1
............MA411003-3 ................ Motor.....................................................2 HP, 3 Ph ..............................1
............DC1100-50W ............... Motor Fan Cover (not shown) ................ ...............................................1
............MF411012.................... Motor Fan (not shown)........................... ...............................................1
............CA003030.................... Running Capacitor (not shown)..............30MFD, 300V..........................1
............CA020010.................... Starting Capacitor (not shown)...............200MFD, 125V........................1
5..........411051......................... Switch Box ............................................ ...............................................1
6..........411053......................... Switch Plate........................................... ...............................................1
7..........994542......................... Switch....................................................1 Ph ........................................1
............DC1900-23B ................ Switch....................................................3 Ph ........................................1
8..........IC420002 ..................... Power Cord............................................ ...............................................1
9..........420051......................... Motor Packing ....................................... ...............................................1
10........AB411059 .................... Impeller .................................................12” ..........................................1
11........411036W ..................... Inlet Guard ............................................ ...............................................1
12........427028......................... Inlet Port................................................2 @ 4”.....................................1
13........420203......................... Inlet Cap................................................ ...............................................2
14........430034......................... Inlet Flange Packing.............................. ...............................................1
15........411041W ..................... Base...................................................... ...............................................1
16........402036......................... Pivoting Caster...................................... ...............................................4
17........420012W ..................... Housing ................................................. ...............................................1
18........402004W ..................... Support.................................................. ...............................................3
19........523011W ..................... Hanger Bracket...................................... ...............................................1
20........411009......................... Hose......................................................5”x65(CM)...............................1
21........420010......................... Ring Clamp ...........................................5” ............................................2
22........402040......................... Hanger ..................................................30 Micron Bag Hanger ............1
............AB430039 .................... Hanger ..................................................5 Micron Bag Hanger ..............1
24........708698......................... Filter Bag...............................................30 Micron Bag.........................1
............708702......................... Filter Bag...............................................5 Micon Bag............................1
25........AB410012 .................... Retainer Strap ....................................... ...............................................1
26........708699A ...................... Collection Bag ....................................... ...............................................1
27........450038......................... Bracket Cap........................................... ...............................................1
31........ST039304 .................... Tapping Screw.......................................M3.5x12(AB)...........................6
32........KS050525 .................... Key........................................................5x5x25....................................1
34........TS-1540061 ................. Nut ........................................................M8 ........................................10
35........TS-0561031 ................. Nut ........................................................3/8”-16UNC.............................4
36........SH080402.................... Hex Head Bolt .......................................M8x20 L.H ..............................1
37........TS-1490011 ................. Hex Head Bolt .......................................M8x12.....................................4
38........TS-1490021 ................. Hex Head Bolt .......................................M8x16...................................16
39........TS-1490041 ................. Hex Head Bolt .......................................M8x25.....................................4
40........TS-1554041 ................. Pan Head Bolt W/Flange .......................M6x12.....................................2
41........TS-0680031 ................. Flat Washer...........................................M8 ..........................................1
42........TS-1554041 ................. Pan Head Bolt W/Flange .......................M6x12.....................................8
43........TS-0680031 ................. Flat Washer...........................................M8 ........................................34
44........TS-0720081 ................. Spring Washer.......................................M8 ..........................................8
45........TS-1551071 ................. Spring Washer.......................................M10.........................................4
46........ST059304 .................... Tapping Screw.......................................M5x12.....................................2
............DC1200-53................... Grounding Label (not shown) ................. ...............................................1
............DC1200-54................... Direction Label (not shown) ................... ...............................................1
............DC1200A-NP ............... Name Plate (not shown) ........................ ...............................................1
............DC1100-HP.................. Hardware Package (not shown) ............. ...............................................1
............DC1200A-CS ............... Centrifugal Switch (not shown)............... ...............................................1
............DC1900-53................... Warning Label (not shown) .................... ...............................................1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram For 3 Phase 230V/460V Dust Collector
Wiring Diagram For Single Phase 230V Only Dust Collector
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|