Operating Instructions and Parts Manual
Dust Collector
Models: DC-1100BK,-1100CK,-1100MK
DC-1100BK
DC-1100CK
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-708636
Ph.: 800-274-6848
Revision E 03/2011
Copyright © 2011 Walter Meier (Manufacturing) Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service.................................................................................................................................2
Table of Contents ......................................................................................................................................3
Warnings...................................................................................................................................................4
Introduction ...............................................................................................................................................5
Specifications ............................................................................................................................................6
Unpacking.................................................................................................................................................7
Shipping Content .......................................................................................................................................7
Base Unit ...............................................................................................................................................7
Canister Filter Kit....................................................................................................................................8
30-Micron Bag Filter Kit...........................................................................................................................8
5-Micron Bag Filter Kit ............................................................................................................................8
Base Unit Assembly...................................................................................................................................9
Base......................................................................................................................................................9
Motor and Fan Assembly ........................................................................................................................9
Connector Housing.................................................................................................................................9
Hose....................................................................................................................................................10
Filter Bag Kit Assembly ............................................................................................................................11
Filter Bag Installation ............................................................................................................................11
Collector Bag Installation (30 Micron Kit)................................................................................................11
Collector Bag Installation (5 Micron Kit)..................................................................................................11
Canister Kit Assembly ..............................................................................................................................12
Canister Filter.......................................................................................................................................12
Collector Bag .......................................................................................................................................12
Electrical Connections..............................................................................................................................13
Turning the Machine On & Off ..................................................................................................................13
All Models ............................................................................................................................................13
Remote Control (Optional Accessory) ....................................................................................................13
Dust Collector RF Remote Power Control (Optional) ..................................................................................13
Turning the DC-RC On & Off.................................................................................................................13
Changing Operating Frequency.............................................................................................................14
Installing the DC-RC Remote Power Control (Optional Accessory)...........................................................14
Maintenance............................................................................................................................................15
Cleaning the Filter Bag – DC-1100BK and DC-1100MK ..........................................................................15
Removing the Collector Bag–DC-1100BK ..............................................................................................15
Cleaning the Filter – DC-1100CK...........................................................................................................15
Removing the Collector Bag–DC-1100CK and DC-1100MK ....................................................................15
Motor...................................................................................................................................................15
Connecting the Dust Collector to a Machine ...........................................................................................15
Grounding the Dust Collection System...................................................................................................15
Parts Breakdown – DC-1100 Dust Collectors .........................................................................................16
Parts List – DC-1100 Dust Collectors.....................................................................................................17
Canister Filter Assembly .......................................................................................................................18
30-Micron Filter Bag Assembly ..............................................................................................................19
5-Micron Filter Bag Assembly................................................................................................................20
Wiring Diagram – DC-1100 Dust Collectors............................................................................................21
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
1. Read and understand the entire owner's manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of
these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a dust collector, do not use until proper training
and knowledge have been obtained.
5. Do not use this dust collector for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that
may result from that use.
6. Always wear approved safety glasses/face shields while using this dust collector. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this dust collector, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face
or dust masks that are specifically designed to filter out microscopic particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches
are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes,
use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly repaired or
replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings,
metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with
any part of the dust collector.
23. Use recommended accessories; improper accessories may be hazardous.
24. Maintain tools with care. Follow instructions for lubricating and changing accessories.
25. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not
use your hands.
26. Do not stand on the machine. Serious injury could occur if the machine tips over.
27. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
28. Remove loose items and unnecessary work pieces from the area before starting the machine.
29. Never place hands near the inlet of the machine.
30. Always make certain machine is off and unplugged when making any connections to the inlet.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
- - SAVE THESE INSTRUCTIONS - -
Introduction
This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance
procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on installation, safety
precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has
been designed and constructed to provide years of trouble free operation if used in accordance with
instructions set forth in this manual. If there are any questions or comments, please contact either your local
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
DC-1100BK (Base Machine with 30 Micron Filter Bag Kit) ..............................................................708636K
DC-1100MK (Base Machine with 5 Micron Filter Bag Kit).............................................................708636MK
DC-1100CK (Base Machine with Canister Filter Kit) .................................................................... 708636CK
Base Machine (All Models)
Model .....................................................................................................................................DC-1100
Stock Number ...........................................................................................................................708636
Impeller Diameter ............................................................................................................................. 11
Sound Rating at 3 foot distance................................................................................................70-80 db
1-Hose Connection Diameter (in.)........................................................................................................ 6
2-Hose Connection Diameter (in.)........................................................................................................ 4
Air Flow (CFM).............................................................................................................................1,100
Velocity at 4” (FPM)......................................................................................................................8,464
Static Pressure (inch of water)........................................................................................................ 10.5
Overall Dimensions, approx. (with filter kit installed) (in.) ............................................... 37L x 28W x 79H
Motor................................................... TEFC, 1-1/2 HP, 1PH, 115/230V, Prewired 115V, 11/5.5 A, 60Hz
Net Weight, approximate (lbs) ......................................................................................................... 103
30 Micron Filter Bag Kit
Stock Number .........................................................................................................................708636F
Filter Bag Efficiency.......................................................................................96% of 30 micron particles
Filter Bag Length, installed (in.) ......................................................................................................... 32
Filter and Collector Bag Diameter (in.) ............................................................................................... 20
Collector Bag Capacity (cu. ft.)......................................................................................................... 5.3
Collector Bag Length (in.) ................................................................................................................. 29
5 Micron Filter Bag Kit
Stock Number ......................................................................................................................708636MF
Filter Bag Efficiency.....................................98% of 5 micron particles; 92% of 3 micron; 74% of 1 micron
Filter Bag Length, installed (in.) ......................................................................................................... 32
Filter and Collector Bag Diameter (in.) ............................................................................................... 20
Collector Bag Capacity (cu. ft.)......................................................................................................... 5.3
Collector Bag Length, installed (in.) ................................................................................................... 29
Canister Filter Kit
Stock Number .........................................................................................................................708639B
Canister Length (in.) ......................................................................................................................... 25
Canister Efficiency................................................... 86% of 1 micron particles; 98% of 2 micron particles
Collector Bag Diameter (in.) .............................................................................................................. 20
Collector Bag Capacity (cu. ft.)......................................................................................................... 5.3
Collector Bag Length, installed (in.) ................................................................................................... 29
IR Remote Control Unit (Optional Accessory)
Stock Number (main unit and remote control switch) (115V only)............................................... 708636C
Stock Number (Remote Control Switch only).............................................................................708636T
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier (Manufacturing) Inc., reserves the right to change specifications at any
time and without prior notice, without incurring obligations.
Read and understand the entire contents of this manual before attempting set-up or
operation! Failure to comply may cause serious injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Shipping Content
The table below lists the shipping cartons that are
included with the models of the DC-1100 Dust
Collector.
Base Unit
(SN 708636)
1 – Housing (A)
1. Locate your particular model and verify that you
have received all of the correct cartons.
2 – Hose Clamps (B)
1 – Hose (C)
1 – Impeller (Motor/Fan Assembly) (D)
1 – Inlet Port (E)
1 – Impeller Cover (F)
3 – Support Legs (G)
1 – Base (H)
2. Check contents of each carton against the ship-
ping content listings on this and the following
page.
3. Report any damage to your distributor.
4 – Casters (J)
1 – Cone (K)
1 – Support Bracket (L)
1 – Owner's Manual (not shown)
1 – Warranty Card (not shown)
1 – Hardware Bag, Base Unit (SN DC1100-HP)
4. Do not discard any shipping material until after
the dust collector has been assembled and is
running properly.
x
x
x
x
DC-1100BK
DC-1100CK
DC-1100MK
x
x
Table – DC-1100 Dust Collector cartons
Hardware Bag for Base Unit (SN DC1100-HP)
16 – M8 x 16 Hex Cap Screws (K)
22 – M8 Flat Washers (L)
08 – M6 x 12 Pan Head Flange Screws (M)
06 – M8 Hex Nuts (N)
Base Unit Hardware
Base Machine Shipping Contents
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter Kit
(SN 708639B)
30-Micron Bag Filter Kit
(SN 708636F)
1 – Handle (O)
1 – Upper Bag Hanger (Y)
1 – Hanger Bracket (Z)
1 – Collector Bag (X)
1 – Filter Bag (W)
1 – Canister Filter (P)
1 – Snap Ring (Q)
5 – Collector Bags (R)
1 – Canister Filter Hardware Bag (SN DC1100-CHP)
Contains:
1 – Retainer Strap (AA)
(2) M10 Hex Nuts (S)
(2) M10 Flat Washers (T)
(1) M10 Lock Washer (U)
(4) Knobs (V)
Filter Bag Kit Contents
5-Micron Bag Filter Kit
(SN 708636MF)
1 – Upper Bag Hanger (BB)
1 – Hanger Bracket (CC)
1 – Filter Bag (DD)
5 – Collector Bags (EE)
1 – Retainer Strap (FF)
1 – Snap Ring (GG)
Canister Filter Kit Contents
Canister Filter Hardware
(SN DC1100-CHP)
Canister Filter Hardware
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Unit Assembly
Base
1. Install four casters to the underside of the base as
pictured in Fig. 2.
Referring to Figure 1:
2. Thread the hex nut (B) onto the caster shaft. Then
slide the lock washer (A) over the caster shaft.
Thread the caster shaft into the threaded hole on
the underside of the base, turn until snug. Tighten
the nut (B) against the base with a 14mm wrench.
This will give the caster proper clearance.
Figure 1
Motor and Fan Assembly
Referring to Figure 2:
3. Place the base (C) with casters on the ground.
Attach the motor and fan assembly (A) to the base
using four each M8 x 16 hex cap screws, and M8
flat washers (B). Tighten with a 13mm wrench.
Figure 2
The dust collector must not be
connected to the power source during assembly.
Failure to comply may result in serious injury!
Referring to Figure 3:
4. Attach impeller cover (A) to impeller housing (D)
using eight M6 x 12 pan head screws (B). Press
the inlet ports (C) onto the inlet guard until it snaps
into place.
To reduce the risk of injury from
moving parts, always keep inlet port covered with
the caps provided, if they are not connected to a
hose. Failure to comply may result in serious
injury!
Figure 3
Connector Housing
5. Attach three support legs (A, Fig. 4) to the base
using six M8 x 16 hex cap bolts and six M8 flat
washers (B, Fig. 4). Hand-tighten only at this time.
Figure 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Install the housing (A, Fig. 5) to two support
legs (B, Fig. 5) using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts (C,
Fig. 5). Be sure hose opening faces fan housing.
Note: For filter bag models only – Before attaching
third support bracket place the hanger bracket (D,
Fig.5) between the support bracket and the
housing. This action is not necessary for canister
filter units.
7. Tighten all nuts and bolts at this time with a 13mm
wrench.
Figure 5
Hose
Referring to Figure 6:
8. Attach the hose (B) between the collector housing
(A) and the impeller housing (D) with two clamps
(C). Tighten the clamps to secure the hose.
This completes the Base Unit assembly. If you
purchased the DC-1100BK or DC-1100MK Dust
Collector (filter bag versions), continue on the
following page. If you purchased the DC-1100CK Dust
Collector (canister filter version), proceed to Canister
Kit Assembly section on page 12.
Figure 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Filter Bag Kit Assembly
If you purchased a DC-1100BK, or DC-1100MK Dust
Collector, this section describes the assembly and
installation of the contents of the Filter Bag Kit (SN
708636F or 708636MF).
Filter Bag Installation
Referring to Figure 7:
1. Place the hanger (A) on the hanger bracket (B).
2. Slide the filter bag loop (C) over the hanger hook.
3. Feed the retainer strap (D) through the loops on
the filter bag (E) and fasten to the collector
housing (F).
Collector Bag Installation (30 Micron Kit)
Referring to Figure 8:
4. Insert the ring of the collector bag (A) at an angle
into the housing (B) through the opening at the
bottom. Pull down on the bag to make sure it
“seats” in the housing.
Figure 7
5. Position the plastic window in front so that you can
easily see when the collector bag is full.
Collector Bag Installation (5 Micron Kit)
The 5-Micron Filter Bag Kit includes clear plastic
collector bags. Refer to Figures 11 and 12 on the next
page, along with the accompanying instructions, to
install these.
After completing the filter bag and collector bag
installation, proceed to Electrical Connections.
Figure 8
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Kit Assembly
If you purchased Model DC-1100CK Dust Collector,
this section describes the assembly and installation of
the contents of the Canister Kit (SN 708639B).
Canister Filter
1. Mount the handle onto the canister filter with two
M10 hex nuts, two M10 flat washers, and a M10
lock washer (Figure 9).
2. Mount the canister filter on top of the collector
housing (A, Fig. 5) and tighten the knobs on the
canister filter (Figure 9).
Figure 9
Collector Bag
3. Place the snap ring over the top of the plastic bag
and fold the bag over the ring approximately three
inches, as shown in Figure 10.
Figure 10
4. Insert the snap ring (A, Figure 11) of the collector
bag into the bottom of the housing at an angle.
5. Pull down on the snap ring to make sure it seats in
the housing.
Note: Make sure the snap ring “snaps” into place
in the housing, and also that the plastic bag hangs
down approximately 3 inches so that there are no
air leaks.
Figure 11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Dust Collector RF Remote
All electrical connections must
be done by qualified
electrician. All adjustments or repairs must be
done with the dust collector disconnected from
the power source, unplugged. Failure to comply
may result in serious injury!
Power Control (Optional)
a
The DC-RC Remote Power Control (Figure 14)
should be used for activating Dust Collection units
powered by 115V only up to 1-1/2HP. The DC-RC
Remote Power Control unit is rated at 115V, Single
Phase only. Use an outlet rated at least 20 amps.
The circuit for the device being controlled by the DC-
RC should also be protected by a minimum 20 amp
circuit breaker or fuse.
The DC-1100 dust collectors (all models) are rated at
115/230V, Prewired 115V. Use a plug and outlet
rated at least 20 amps. The circuit for the machine
should also be protected by a minimum 20 amp
circuit breaker or fuse. Keep in mind that a circuit
being used by other machines, tools, lights, heaters,
etc. at the same time will add to the electrical load.
Before hooking up to the power source, make sure
that the switch is initially in the off position on both
the dust collector and remote control unit (Figure 12).
A dedicated circuit to the dust collector will give you
the best results since dust collectors are generally
used at the same time other tools are running.
Turning the DC-RC On & Off
This machine is intended for
indoor use only.
1. Plug the dust collector into the main unit
(Figure 14) and plug the main unit into the power
outlet.
Turning the Machine On & Off
This machine is intended for
indoor use only.
To start a machine or device:
2. Turn the machine itself on.
All Models
3. On the main unit place the switch to the ON
position (Figure 12A). The red LED on the main
unit should light up.
Before hooking up to the power source, make sure
that the switch is in the off position.
Turn the dust collector on by pressing the Start
button mounted next to the motor. Press the Stop
button to turn off the dust collector.
4. Press the button on the remote control
transmitter (Figure 13) to turn the machine on.
5. To stop the machine, press the button on the
Remote Control (Optional Accessory)
remote control transmitter again.
The DC-RC RF Remote Power Control unit is
available as an optional accessory (see your dealer
or contact Customer Service by calling the number
on the cover).
Important: The DC-RC Remote Power Control (SN
708636C) can be used for activating Dust Collection
units powered by 115V only up to 1-1/2HP. If your
dust collector is currently set up for 230V operation or
you choose to convert it to 230V at a later time, you
must purchase the DC-RC230 Remote Power
Control unit (SN 708636D).
Figure 13
Figure 12A
Figure 12B
When the machine is running, it can be stopped by
placing the switch on the main unit in the off position
(Figure 12B). To restart, repeat steps 3 and 4.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Operating Frequency
Installing the DC-RC Remote Power
Control (Optional Accessory)
If several devices are controlled by the same type
remote control unit, each remote control unit can be
set to operate at its’ own unique operating frequency
as follows:
The DC-RC Remote Power Control unit can be
placed anywhere for convenience and portability if
used to control other machines or it can be mounted
as a permanent part of a machine, such as the DC-
1100 Dust Collector.
Referring to Figure 14:
1. Unplug the DC-RC Remote Power Control unit.
To mount the DC-RC Remote Power Control (refer to
2. Remove the back covers of the main unit (A) and
remote control switch (B).
Figure 15):
Note: Mounting hardware is not included and must
3. Locate the DIP switch (C) in each unit.
be supplied by the machine’s owner or user.
1. Place RC Power Control Unit (A) on the open
clearing of the base (B) of the dust collector near
the motor (C).
4. Change the position of the DIP switches in the
main unit (A) to any combination desired as long
as they are not the same as other units that may
be present and located within the radio frequency
range.
2. Using a marker, mark the base through the
mounting holes of the power control units
mounting tabs.
5. Set the DIP switches (C) in the remote control
switch (B) to match the switch settings in the
main unit (A).
3. Drill two holes (D) through the base where
marked.
6. Replace the back covers to the main unit and
remote control switch.
4. Insert screws through the tabs and base. Place
washers and hex nuts on the threaded ends of
the screw underneath the base and tighten.
7. Operate a device as described in Turning the
DC-RC On & Off and verify that other devices
using the same type remote control do not turn
on.
Figure 14
Figure 15
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Filter – DC-1100CK
Maintenance
Never perform maintenance on
this machine before turning switch off and
removing plug from power source. Failure to
comply may cause serious injury!
Never perform maintenance on
this machine before turning switch off and
removing plug from power source. Failure to
comply may cause serious injury!
Clean both the canister filter and collector bags
frequently to keep the collector's performance at its
optimum.
Cleaning the Filter Bag – DC-1100BK and
DC-1100MK
To clean the filter, turn the handle a couple of
rotations so the dust falls into the collection bag.
Wearing
a
particle mask or
respirator for protection against fine dust
particles during cleaning is highly recommended.
Removing the Collector Bag–DC-1100CK
and DC-1100MK
During first use and after cleaning, the filter bag may
allow some dust to escape. This is normal and will
stop after a short period of time.
Wearing
a
particle mask or
respirator for protection against fine dust
particles during cleaning is highly recommended.
Clean both the filter and collector bags frequently to
keep the collector's performance at its optimum. To
clean:
1. Disconnect the machine from the power source
outlet.
1. Disconnect the machine from the power source.
2. Remove the collector bag by pushing the ring of
the collector bag upwards at an angle and
pulling the bag and snap ring out.
2. Unhook the filter bag from the hanger and shake
the bag so that the majority of the dust falls into
the collector bag.
3. Empty the contents into an appropriate
container.
3. Loosen the retaining strap, and remove the filter
bag from the housing.
To replace the collector bag, refer to the Collector
Bag Installation on page 12.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and re-attach to the
housing using the retainer strap to secure.
Motor
Make frequent inspections of the motor fan and blow
out (with low pressure air hose) or vacuum any
accumulation of foreign material in order to maintain
normal motor ventilation.
Removing the Collector Bag–DC-1100BK
1. Disconnect the machine from the power source.
2. Remove the collector bag by pushing the ring of
the collector bag upwards and pulling the bag
out at an angle.
Connecting the Dust Collector to a
Machine
3. Empty the contents into an appropriate
container.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer vent
hose is not acceptable for this purpose. Contact your
nearest JET distributor for the full line of JET Dust
Collector Hoses and Accessories. Customize your
installation and obtain maximum performance with
JET dust hoods, hoses, clamps, fittings, and blast
gates.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and insert into the
housing.
To replace the collector bag, refer to Collector Bag
Installation on page 11.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer vent
hose is not acceptable for this purpose. Contact your
nearest JET distributor for the full line of JET Dust
Collector Hoses and Accessories. Customize your
installation and obtain maximum performance with
JET dust hoods, hoses, clamps, fittings, and blast
gates.
Grounding the Dust Collection System
The dust collection system includes the dust collector
and the hose, or ductwork you use to connect the
tools. The dust collector is grounded through the
ground wire in the cord. The hose or ductwork you
use to connect the tool to the dust collector must also
be grounded.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown – DC-1100 Dust Collectors
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List – DC-1100 Dust Collectors
Ordering Replacement Parts
To order parts or reach our service department, call 800-274-6848, Monday through Friday (see our website for
when you call will allow us to serve you quickly and accurately.
Index No. Part No.
Description
Size
Qty
1.............. 411035W ................Impeller Housing.............................................................................................1
2.............. 411026W ................Motor Bracket.................................................................................................1
3.............. 998621....................Strain Relief ...................................................................................................1
4.............. MA2041J1W............Motor...............................................................1-1/2 HP, 1Ph.........................1
................ DC1100-50W...........Motor Fan Cover (not shown) ..........................................................................1
................ DC1100-51..............Motor Fan (not shown) ....................................................................................1
................ DC1100-54..............Running Capacitor (not shown)..........................40uf, 250V .............................1
................ DC1100-55..............Starting Capacitor (not shown)...........................400MFD, 125VAC...................1
................ DC1100-52..............Centrifugal Switch (not shown) ........................................................................1
................ DC1100-53..............Centrifugal Switch Rotor (not shown) ...............................................................1
5.............. 411051....................Switch Box ....................................................................................................1
6.............. 411053....................Switch Plate ..................................................................................................1
7.............. 994542....................Switch ...........................................................................................................1
8.............. 999910....................Power Cord....................................................................................................1
9.............. 420051....................Motor Packing ................................................................................................1
10............ AB411040 ...............Impeller............................................................11”.........................................1
11............ 411036W ................Inlet Guard .....................................................................................................1
12............ 427028....................Inlet Port ..........................................................2 @ 4”....................................1
13............ 420203....................Inlet Cap ........................................................................................................1
14............ 430034....................Inlet Flange Packing .......................................................................................1
15............ 411041W ................Base..............................................................................................................1
16............ 402036....................Pivoting Caster ...............................................................................................4
17............ 420012W ................Housing ...........................................................20”.........................................1
18............ 402004W ................Support..........................................................................................................3
20............ 411009....................Hose..............................................................................................................1
21............ 420010....................Ring Clamp ......................................................5”...........................................2
31............ ST050204 ...............Tapping Screw .................................................M5x10....................................6
32............ KS050525 ...............Key..................................................................5x5x25 mm ............................1
34............ TS-1540061 ............Hex Nut............................................................M8.......................................10
35............ TS-0561031 ............Hex Nut............................................................3/8”-16UNC............................4
36............ TS-1490031 ............Hex Cap Screw ................................................M8x20....................................1
37............ TS-1490011 ............Hex Cap Screw ................................................M8x12....................................4
38............ TS-1490021 ............Hex Cap Screw ................................................M8x16..................................16
39............ TS-1490041 ............Hex Cap Screw ................................................M8x25....................................4
40............ SF069300 ...............Pan Head Screw W/Flange ...............................M6x12....................................2
41............ TS-1550061 ............Flat Washer......................................................M8.........................................1
42............ SF069300 ...............Pan Head Screw W/Flange ...............................M6x12....................................8
43............ TS-1550061 ............Flat Washer......................................................M8.......................................34
44............ TS-2361081 ............Lock Washer ....................................................M8.........................................8
45............ TS-2361101 ............Lock Washer ....................................................M10.......................................4
46............ ST059200 ...............Tapping Screw .................................................M5x8 .....................................2
................ DC1200-53..............Grounding Label (not shown)...........................................................................1
................ DC1200-54..............Direction Label (not shown) .............................................................................1
................ DC1100-ID ..............I.D. Label (not shown) .....................................................................................1
................ DC1100-HP.............Hardware Package for Base Unit .....................................................................1
................ DC1100-HP2...........Hardware Package for Cone Assembly ............................................................1
................ DC1100-WL ............Warning Label (not shown)..............................................................................1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter Kit (708639B)
Index No. Part No.
Description
Size
Qty
................ 708639B .................Canister Filter Kit (index #1-24) .........................................................................
1.............. 331050....................Handle ...........................................................................................................1
2.............. TS-1540071 ............Hex Nut............................................................M10.......................................2
3.............. TS-1550071 ............Flat Washer......................................................M10.......................................2
4.............. TS-2361101 ............Lock Washer ....................................................M10.......................................1
5.............. BR000052...............Rivet ................................................................5-2.........................................3
6.............. 331014....................Bracket ..........................................................................................................1
7.............. 150623....................Pad................................................................................................................1
8.............. 331051....................Soft Grip Handle.............................................................................................2
9.............. TS-1540041 ............Hex Nut............................................................M6.........................................8
10............ 708739....................Filter ..............................................................................................................1
11............ 331052....................Shaft..............................................................................................................1
12............ TS-1482041 ............Hex Cap Screw ................................................M6X20...................................4
13............ TS-2361061 ............Lock Washer ....................................................M6.........................................4
14............ TS-1550041 ............Flat Washer......................................................M6.........................................4
15............ 331012....................Scraper..........................................................................................................2
16............ 331017....................Strip...............................................................................................................2
17............ 331015....................Press Plate.....................................................................................................2
18............ TS-1482021 ............Hex Cap Screw ................................................M6x12....................................4
19............ 331037....................Knob..............................................................................................................4
20............ 331031....................Pad................................................................................................................1
21............ 331009....................Support..........................................................................................................1
22............ ST049200 ...............Tapping Screw .................................................M4X8.....................................4
23............ 331038....................Snap Ring ......................................................................................................1
24............ 709563....................Plastic Bag (Package of 5) ..............................................................................1
................ DC1100-CHP ..........Canister Hardware Package..............................................................................
18
Download from Www.Somanuals.com. All Manuals Search And Download.
30-Micron Filter Bag Kit (708636F)
Index No. Part No.
Description
Size
Qty
................ 708636F..................30-Micron Filter and Collection Bag Kit (index # 1-5) ...........................................
1.............. 708698....................Filter Bag ........................................................30 Micron...............................1
2.............. AB410012 ...............Retainer Strap................................................................................................1
3.............. 708699A .................Collector Bag .................................................................................................1
4.............. 430038....................Hanger ..........................................................................................................1
5.............. 523011W ................Hanger Bracket ..............................................................................................1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5-Micron Filter Bag Kit (708636MF)
Index No. Part No.
Description
Size
Qty
................ 708636MF...............5-Micron Filter and Collection Bag Kit (index # 1-6).............................................
1.............. 708706....................Filter Bag ........................................................5 Micron.................................1
2.............. AB410012 ...............Retainer Strap................................................................................................1
3.............. 331038....................Snap Ring ......................................................................................................1
4.............. 709563....................Plastic Bag (Package of 5) ..............................................................................1
5.............. 430038....................Hanger ..........................................................................................................1
6.............. 523011W ................Hanger Bracket ..............................................................................................1
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram – DC-1100 Dust Collectors
21
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|