Operating Instructions and Parts Manual
Tilting Table Hollow Chisel Mortiser
Model: 719T
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. M-2474002
Revision A 03/04
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service....................................................................................................................................2
Table of Contents..........................................................................................................................................3
Warnings .......................................................................................................................................................4
Introduction ...................................................................................................................................................6
Specifications................................................................................................................................................6
Unpacking .....................................................................................................................................................7
Contents of the Mortiser Carton ................................................................................................................7
Contents of the Stand Carton....................................................................................................................7
Assembly.......................................................................................................................................................8
Securing Machine to Stand .......................................................................................................................8
Wooden Table ...........................................................................................................................................8
Operating Handle ......................................................................................................................................8
Installing Chisel and Bit .............................................................................................................................9
Work Stop..................................................................................................................................................9
Electrical......................................................................................................................................................10
Power Connection ...................................................................................................................................10
Grounding Instructions ............................................................................................................................10
Operating Controls......................................................................................................................................10
Start/Stop Switch.....................................................................................................................................10
Adjustments ................................................................................................................................................11
90° Chisel to Worktable Calibration.........................................................................................................11
Chuck Extension Adaptor........................................................................................................................11
Depth Stop Rod Adjustment....................................................................................................................12
Table Position..........................................................................................................................................12
Forward/Backward Table Movement...................................................................................................12
Lateral Table Movement......................................................................................................................12
Table Tilt Control..................................................................................................................................12
Chisel Parallel to Workpiece ...................................................................................................................13
Operation.....................................................................................................................................................13
Maintenance................................................................................................................................................14
General....................................................................................................................................................14
Sharpening Chisel and Bit.......................................................................................................................14
Bit.........................................................................................................................................................14
Chisel...................................................................................................................................................14
Lubrication...................................................................................................................................................15
Parts............................................................................................................................................................15
Replacement Parts..................................................................................................................................15
719T Mortiser Parts List ..........................................................................................................................16
719T Mortiser Assembly..........................................................................................................................18
719T Mortiser Stand Parts List................................................................................................................19
719T Mortiser Stand Assembly ...............................................................................................................19
Optional Accessories...............................................................................................................................20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This mortiser is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a mortiser, do not use until proper training
and knowledge have been obtained.
5. Do not use this mortiser for other than its intended use. If used for other purposes, WMH Tool Group
disclaims any real or implied warranty and holds itself harmless from any injury that may result from
that use.
6. Always wear approved safety glasses/face shields while using this mortiser. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this mortiser, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Make sure the mortiser is firmly secured to the floor before use.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
blahblahblah
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
23. Maintain a balanced stance at all times so that you do not fall or lean against the chisel and drill bits
or other moving parts. Do not overreach or use excessive force to perform any machine operation.
24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
25. Use recommended accessories; improper accessories may be hazardous.
26. Maintain tools with care. Keep chisel and drill bits sharp and clean for the best and safest
performance. Follow instructions for lubricating and changing accessories.
27. Make sure the work piece is securely attached or clamped to the table. Never use your hand to hold
the work piece.
28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
29. Do not stand on the machine. Serious injury could occur if the machine tips over.
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
31. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by POWERMATIC covering the safe operation and maintenance procedures for
a Model 719T Tilting Table Hollow Chisel Mortiser. This manual contains instructions on installation,
safety precautions, general operating procedures, maintenance instructions and parts breakdown. This
machine has been designed and constructed to provide years of trouble free operation if used in
accordance to instructions set forth in this manual. If there are any questions or comments, please
contact either your local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web
Specifications
Model No.................................................................................................................................................719T
Stock No..........................................................................................................................................1791264K
Stock No – Mortiser only.................................................................................................................2474002T
Stock No – Stand only.....................................................................................................................6294235T
Motor ............................................................................................... 1 HP, 1 PH, 115V/230V, Prewired 115V
Spindle speed ................................................................................................................................1725 RPM
Table tilt ............................................................................................................................................ 0° to 35°
Chisel capacity................................................................................................................................... 1/4" - 1"
Chisel shank diameters ........................................................................................................5/8", 3/4", 1-1/8"
Maximum chisel stroke.........................................................................................................................10-3/4"
Maximum head stroke..................................................................................................................................6"
Chisel center to fence distance....................................................................................................................4"
Chuck capacity..........................................................................................................................................1/2"
Bushing size..........................................................................................................................5/8", 3/4", 1-1/8"
Longitudinal table travel .......................................................................................................................15-1/2"
Cross table travel .........................................................................................................................................4"
Table size..................................................................................................................................... 7" x 20-1/4"
Fence size.............................................................................................................................. 4-1/2" x 20-1/4"
Base size...........................................................................................................................................14" x 16"
Overall height on base ...............................................................................................................................60"
Overall dimensions...........................................................................................21-1/4" L x 21-5/8" W x 74" H
Weight - Mortiser......................................................................... Net weight 230 lbs., Gross weight 242 lbs.
Weight - Stand .................................................................................Net weight 46 lbs., Gross weight 50 lbs.
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, WHM Tool Group reserves the right to change specifications at any time and
without prior notice, without incurring obligations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Remove mortiser and stand from the shipping cartons. Check for damage and ensure all parts are intact.
Any damage should be reported immediately to your distributor and shipping agent. Read the manual
thoroughly to familiarize yourself with the correct assembly and maintenance procedures and proper
safety precautions.
Contents of the Mortiser Carton
1 ea – Mortiser (not shown)
Contents of the Stand Carton
1
1
Stand (not shown)
Hardware package – (4) M8 x 45 Hex Cap
Screws, (4) M8 Lock Washers (not shown)
1. 1 ea – Wooden Table
2. 2 ea – M6 x 20 Phillips Head Screws
3. 2 ea – Handwheel Handles
4. 1 ea – Chuck Key
5. 1 ea – Chuck Removal Wrench
6. 1 ea – 23mm Box Wrench
7. 1 ea – Operating Handle
8. 1ea – Chuck Extension Adaptor
9. 2 ea – Chisel Bushings (3/4", 1-1/8")
Note: The Mortiser also comes with a 5/8"
bushing already installed.
10. 1 Work Stop Assembly
Contents of the Mortiser Carton
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Do not connect the machine
source until completely
to
power
assembled. Read and understand the entire
manual.
Securing Machine to Stand
The mortiser should be secured to the stand
with four M8 x 45 hex cap screws and M8 lock
washers (provided) using the holes in the base.
Make sure there is enough room on each side
of the mortiser for the size stock you plan to
use.
Wooden Table
Referring to Figure 1:
1. Place the wooden table (A) in position on
the slide (B).
Figure 1
2. Secure with two Phillips head screws
provided (C).
Operating Handle
Referring to Figure 2:
1. Fasten operating handle (A) to the hub (B)
and tighten with a 14mm open-end wrench.
2. Raise mortising machine head to the up
position by moving the operating handle
(A) up.
Note: The handle assembly is spring-loaded
and can be repositioned by pulling out the
hub (B) and repositioning it on the pinion
shaft (C).
Figure 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Chisel and Bit
Referring to Figure 3:
1. Loosen the lock screw.
2. Insert the chisel bushing into the head with
the hole facing forward to line up with the
lock screw. Screw in the lock screw just
enough so the screw extends into the hole
of the bushing, holding it in place.
3. Push the chisel up through the bushing,
bringing it to rest against the shoulder of
the bushing. Then lower the chisel
approximately 1/16" to 3/16", depending on
the type of wood being worked.
Note: Set the slot in the side of the chisel to the
left or right, if the workpiece is to be moved
laterally and front or back if it is to be moved
from front to back. Move the workpiece so that
the slot in the chisel is releasing chips into the
already cut part of the workpiece (see
Figure 14).
4. Tighten the lock screw to hold the chisel in
Figure 3
place.
5. Push the bit up through the chisel opening
as far as it will go. Lock the drill bit in place
with the chuck key.
6. Loosen the lock screw and push the chisel
up against the bushing, then tighten the
lock screw. This should provide the proper
distance between the points of the chisel
and the bit.
Note: This would be a good place to make sure
that the chisel is parallel to the workpiece. See
the Chisel Parallel to Workpiece section.
Work Stop
The work stop can be mounted to either end of
the table through the holes in the back of the
table, as shown in Figure 4. It is tightened into
place by means of thumbscrews.
THUMBSCREWS
HOLES
Figure 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical
Power Connection
Do not operate this
machine in damp
locations.
A separate electrical circuit should be used for
your machines. This circuit should not be less
than #12 wire and should be protected with a
20 Amp time lag fuse. If an extension cord is
used, use only 3-wire extension cords which
have 3-prong grounding type plugs and
matching receptacle, which will accept the
machine’s plug. Before connecting the machine
to the power line, make sure the switch is in the
Off position and be sure that the electric current
is of the same characteristics as indicated on
the machine. All line connections should make
good contact. Running on low voltage will
damage the machine.
Grounding Instructions
This machine must be
grounded while in use to
protect the user from shock
In the event of a malfunction or breakdown,
grounding provides a path of least resistance
for electric current to reduce the risk of electric
shock.
Figure 5
If you are not sure whether your outlet is
properly grounded, consult
electrician.
a
qualified
Referring to Figure 5: As received from the
factory, your mortiser is ready to run at 115-volt
operation. This mortiser is intended for use on
a circuit that has an outlet and a plug that looks
like the one illustrated in (A). A temporary
adaptor, which looks like the adaptor shown in
(B), may be used to connect this plug to a two-
pole receptacle if a properly grounded outlet is
not available. The temporary adaptor should
only be used until a properly grounded outlet
can be installed by a qualified electrician. This
adaptor is not applicable in Canada. The green
colored rigid ear, lug, or tab, extending from the
adaptor, must be connected to a permanent
ground such as a properly grounded outlet box.
Operating Controls
Start/Stop Switch
Referring to Figure 6: The Start/Stop Switch is
located to the left of the motor on the side of
the mortiser. To turn the mortiser on press the
green START (A) button. To stop the mortiser,
push the red STOP (B) button.
Figure 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
90° Chisel to Worktable Calibration
Referring to Figure 7:
Place a square (E) so it rests against the
worktable (B) and chisel (A). If the chisel to
table angle is 90°, no calibration is necessary.
If calibration is required:
1. Loosen the bolt (C) that allows the tilting
base to pivot.
The tilting base is heavy. If
raised, take extra precaution not to let it
drop on hands or fingers. Injury can result.
2. Adjust the adjustment screws (F) until the
chisel to table angle is 90°. Calibration is
then complete.
3. Retighten the bolt (C).
Upon completion, make sure that the pointer
points to 0°. Calibrate if necessary.
Figure 7
Chuck Extension Adaptor
The provided Chuck Extension Adaptor (C) is
intended to lower the chuck for use with
after-market chisels (chisels other than the
POWERMATIC brand) that may require a
spacer due to varying lengths in shanks.
To install the adaptor, first remove the chisel
and bit (see the Installing Chisel and Bit
section). Then, referring to Figure 8:
1. Loosen the lock screw (E) enough to
remove the chisel bushing (F).
2. Remove the chisel bushing (F). This is
necessary to provide enough clearance
when installing the chuck and extension
adaptor.
3. Unscrew the chuck release nut (A)
counterclockwise with the wrench provided
to force the chuck (D) off the shaft (B).
It may be necessary to hold the shaft
stationary while turning the nut. This can
be done by inserting the chuck key handle
into the hole in the chuck and allowing it to
wedge against the edge of the headstock.
4. When the chuck is off, return the chuck
release nut (A) to its original position on the
shaft (B).
5. Push the adaptor (C) into the chuck (D).
Then push this assembly onto the motor
shaft (B).
Figure 8
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Reinstall the chisel bushing (F) and secure
it loosely with the lock screw (E).
7. Reinstall the chisel and bit (refer to the
Installing Chisel and Bit section).
Depth Stop Rod Adjustment
Referring to Figure 9:
A depth stop rod (A) is provided to limit the
depth of the chisel. To adjust:
A
B
1. Loosen lock lever (B) and lower the depth
stop rod (A) until it comes to rest on top of
the column stop (C).
2. With the operating handle (see Figure 2)
lower the head (E) until the chisel (D) is at
the desired depth.
3. The depth stop rod (A) should still be
resting on top of the column stop (C).
4. Tighten the lock lever (B).
Table Position
E
D
C
The 719T Mortiser is equipped with two
handwheels for table (E, Fig. 10) positioning. In
addition, the table can be tilted up to 35° for
angle mortising.
Forward/Backward Table Movement
Figure 9
1. Loosen the wing screw on the right side of
the middle base under the table.
2. Turn the handwheel (A, Fig. 10) to move
the table the forward or backward.
3. Tighten the wing screw.
Lateral Table Movement
1. Loosen the wing screw located on the back
of the middle base located near the
column.
2. Turn the handwheel (B, Fig. 10) to move
the table to the right or left.
3. Tighten the wing screw.
Table Tilt Control
The tilt table is heavy. When
raised, take extra precaution not to let it
drop on hands or fingers. Injury can result.
Figure 10
1. Loosen bolt (C, Fig. 10) with the 23mm
wrench provided.
2. Pivot the table to adjust the angle up to 35°
using the scale (D) on the tilt bracket as a
guide.
3. Tighten the bolt (C).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chisel Parallel to Workpiece
Referring to Figure 11:
The chisel can be adjusted parallel to the
workpiece as follows:
1. With the left handwheel (A), move the table
back far enough to insert the workpiece (B)
between the chisel (D) and fence.
2. Loosen the lock screw (C). This will allow
the chisel to rotate.
3. Bring the table forward with the handwheel
(A) until the workpiece (B) rests against the
back surface of the chisel (D), but do not
force.
Further adjust the chisel by hand if needed.
4. Tighten the lock screw (C).
Figure 11
Operation
1. Set the depth stop (A, Fig. 12) to the
required depth of cut. Refer to the Depth
Stop Rod Adjustment section.
5. Place workpiece on table (C, Fig. 13) and
clamp it with the vise (A, Fig. 13). Use the
left handwheel (D, Fig. 13) to move table
forward or backward to suit the position of
the mortise on the workpiece.
A
B
6. Adjust the table stops according to the
length of cut required, then tighten the
thumbscrews (B, Fig. 13).
C
D
Before turning the machine
on, verify that the chuck key is not in the
chuck.
7. Turn on the machine and feed the chisel
and bit steadily into workpiece by pulling
down the operating handle.
Figure 12
Note: The rate of feed must be fast enough to
prevent burning at the tip of the bit, but not so
fast as to cause the machine to slow or stall.
The different rates of feed for different woods
must be learned through experience.
F
C
A
8. After the first cut, the workpiece is moved
along with the right handwheel (E. Fig. 13)
for each successive cut. The direction of
movement must allow the chips to clear
freely. Move the workpiece so that the slot
in the chisel is releasing chips into the
already cut part of the workpiece
(Figure 14).
B
E
D
Figure 13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not have the chisel slot
against the blind end of the mortise, as the
chips will not be able to clear the chisel.
This can cause overheating and possible
breakage of chisel or bit.
When cutting deep mortises, make the cut in
several stages of approximately 1" each, to
allow chips to clear. To prevent breakout at the
back of the workpiece when cutting through
mortises, use a piece of scrap material under
the workpiece as support.
Figure 14
Maintenance
Before any intervention on
the machine, disconnect it from the
electrical supply by pulling out the plug or
switching off the main switch! Failure to
comply may cause serious injury.
General
A coat of paste wax applied to the table and
column will help to keep the surfaces clean.
If the power cord is worn, cut, or damaged in
any way, have it replaced immediately.
The Mortiser requires only minor maintenance,
such as cleaning and lubrication and routine
adjustment and sharpening of the chisel and
bit.
Figure 15
Dust the machine down after each use and, as
necessary, use light applications of oil or
grease to lubricate linkages, moving parts, etc.
Sharpening Chisel and Bit
The chisel and bit should be kept sharp for best
performance. Blunt edges will give inaccurate
mortises and can lead to overheating and
breakage to chisel or bit. If chisel and bit are
badly worn and become difficult to sharpen,
they should be replaced.
Bit
Sharpen the bit by using a small, smooth file,
following the original shape of the bit. File the
inside edge of the spur, the sides of the brad
point, and the cutting edge inwards toward the
flute of the bit (Figure 15).
Do not file the outside edge of the spur, as this
will affect the diameter of the bit.
Chisel
Sharpen the chisel with a mortise chisel cutter
with the correct size pilot. (Pilot size will differ
depending on the size of your chisel). Two or
Figure 16
14
Download from Www.Somanuals.com. All Manuals Search And Download.
three turns of the cutter in a carpenter's brace
chuck should be enough to sharpen the chisel,
as shown in Figure 16.
Use a small, triangular, smooth file to relieve
the inner corners of the chisel (Figure 17).
Remove any burrs from the outside of the
chisel with a fine oilstone.
Figure 17
Lubrication
All of the ball bearings are packed with grease
at the factory. They require no further
lubrication.
Periodically grease the gears, racks, and table
pivot points with a #2 tube grease.
Periodically clean and oil any exposed machine
surfaces, such as: dove-tail ways and slides,
and table surface.
Parts
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848 between 7:00 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model
Number and Serial Number of your machine available when you call will allow us to serve you quickly and
accurately.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
719T Mortiser Parts List
Index No. Part No.
Description
Size
Qty
.................2474002T.................719T Mortiser Assy (Items 1 thru 120) .............. ................................................. 1
1 ...............719T-101..................Fixed Base........................................................... ................................................. 1
2 ...............6294125...................Base, Middle ........................................................ ................................................. 1
3 ...............6294126...................Gib........................................................................ ................................................. 1
4 ...............TS-1523061 .............Socket Set Screw.................................................M6×20...................................... 3
5 ...............TS-1540041 .............Hex Nut ................................................................M6............................................ 9
6 ...............6294129...................Lead Screw.......................................................... ................................................. 1
7 ...............TS-1523031 .............Socket Set Screw.................................................M6×10...................................... 4
8 ...............6294131...................Hand wheel.......................................................... ................................................. 1
9 ...............6294132...................Shaft..................................................................... ................................................. 1
10 .............6294133...................Gear ..................................................................... ................................................. 1
11 .............6294134...................C-Clip ................................................................... ................................................. 1
12 .............6294135...................Hand wheel.......................................................... ................................................. 1
13 .............BB-6002ZZ...............Bearing.................................................................6002ZZ..................................... 2
14 .............6294137...................C-Clip ................................................................... ................................................. 2
15 .............TS-1503041 .............Socket Head Cap Screw......................................M6×16...................................... 2
16 .............6294139...................Stop Block............................................................ ................................................. 1
17 .............6294140...................Gib........................................................................ ................................................. 1
18 .............6294141...................Main Table ........................................................... ................................................. 1
19 .............TS-1523011 .............Socket Set Screw.................................................M6×6........................................ 4
20 .............6294143...................Setting Collar........................................................ ................................................. 2
21 .............6294144...................Setting Rod .......................................................... ................................................. 1
22 .............6294145...................Wing Screw..........................................................M6×16...................................... 3
23 .............6294146...................Rack..................................................................... ................................................. 1
24 .............TS-1523071 .............Socket Set Screw.................................................M6×25...................................... 6
25 .............6294148...................Rear Length Setting Rod ..................................... ................................................. 1
26 .............6294149...................Setting Length Block............................................ ................................................. 1
27 .............6294150...................Front Length Setting Rod..................................... ................................................. 1
28 .............6294151...................Wooden Table Insert............................................ ................................................. 1
29 .............TS-2286201 .............Machine Screw, Flat Head, Phillips .....................M6×20...................................... 2
30 .............719T-130..................Column................................................................. ................................................. 1
31 .............6294154...................Wave Washer....................................................... ................................................. 2
32 .............6294155...................Gib........................................................................ ................................................. 1
33 .............6294156...................Headstock ............................................................ ................................................. 1
34 .............719T-134..................Rack..................................................................... ................................................. 1
35 .............TS-1503031 .............Socket Head Cap Screw......................................M6×12...................................... 4
36 .............6294159...................Left Side Cover .................................................... ................................................. 1
37 .............6294160...................Right Side Cover.................................................. ................................................. 1
38 .............TS-1533042 .............Machine Screw, Pan Head, Phillips ....................M5×12...................................... 4
39 .............6294162...................Gear ..................................................................... ................................................. 1
40 .............6294163...................Collar.................................................................... ................................................. 1
41 .............6294164...................Gear Shaft............................................................ ................................................. 1
42 .............6294165...................Handle Hub.......................................................... ................................................. 1
43 .............6294166...................Spring................................................................... ................................................. 1
44 .............6294167...................Washer................................................................. ................................................. 1
45 .............TS-1514021 .............Socket Head Flat Screw ......................................M6×16...................................... 2
46 .............6294169...................Handle.................................................................. ................................................. 1
47 .............6294170...................Handle Grip.......................................................... ................................................. 1
48 .............6294171...................Chuck ..................................................................1/2” & Key................................ 1
49 .............6294172...................Motor, 1HP, 1PH, 115/230V ................................ ................................................. 1
50 .............6294173...................Switch Box ........................................................... ................................................. 1
51 .............TS-081C052.............Machine Screw, Pan Head, Phillips.....................#10-24 × 3/4............................. 2
52 .............6294175...................Switch................................................................... ................................................. 1
53 ............TS-0749042 .............Tapping Screw, Pan Head, Phillips .....................#8 × 5/8 ................................... 2
54 .............TS-1503051 .............Socket Head Cap Screw......................................M6×20...................................... 3
55 .............6294178...................Upper Cylinder Fitting .......................................... ................................................. 1
56 .............719T-156..................Hydraulic Cylinder................................................ ................................................. 1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Index No. Part No.
Description
Size
Qty
57 .............6294180...................C-Clip ................................................................... ................................................. 2
58 .............6294181...................Depth Setting Block ............................................. ................................................. 1
59 .............719T-159..................Depth Setting Rod................................................ ................................................. 1
60 .............6294183...................Universal Handle.................................................. ................................................. 1
61 .............TS-1505041 .............Socket Head Cap Screw......................................M10×30.................................... 4
62 .............TS-2361101 .............Lock Washer........................................................M10.......................................... 8
63 .............6294186...................Clamping Jaw....................................................... ................................................. 1
64 .............6294187...................Clamping Block.................................................... ................................................. 1
65 .............6294188...................Rapid Nut ............................................................. ................................................. 1
66 ............6294189...................Friction Toe.......................................................... ................................................. 1
67 .............6294190...................Spring................................................................... ................................................. 1
68 .............6294191...................Rivet..................................................................... ................................................. 1
69 .............6294192...................Locking Screw...................................................... ................................................. 1
70 .............6294193...................Stop Disc.............................................................. ................................................. 1
71 .............TS-1504051 .............Socket Head Cap Screw......................................M8×25...................................... 2
72 .............TS-1550061 .............Flat Washer..........................................................M8............................................ 2
73 .............TS-1504061 .............Socket Head Cap Screw......................................M8×30...................................... 2
74 .............6294197...................Chisel Locking Screw........................................... ................................................. 1
75 .............6294198...................Bushing ................................................................1-1/8”........................................ 1
75A...........6294221...................Bushing ................................................................3/4”........................................... 1
75B...........6294222...................Bushing ................................................................5/8”........................................... 1
76 .............6294199...................Wheel Handle ...................................................... ................................................. 2
77 .............6294200...................Collar.................................................................... ................................................. 1
78 .............6294201...................E-Clip ................................................................... ................................................. 2
79 ............6294202...................Back Cover........................................................... ................................................. 1
80 .............TS-1532032 .............Machine Screw, Pan Head, Phillips.....................M4 × 10.................................... 6
81 .............6294204...................Chuck Key............................................................ ................................................. 1
82 .............6294205...................Chuck Key Holder................................................ ................................................. 1
83 .............TS-2361051 .............Lock Washer........................................................M5............................................ 1
84 .............TS-1502011 .............Socket Head Cap Screw......................................M5 × 8...................................... 1
85 .............6294208...................Chuck Release Nut.............................................. ................................................. 1
86 .............6294209...................Wave Washer....................................................... ................................................. 1
87 .............6294240...................Cylinder Holder .................................................... ................................................. 2
88 .............6294211...................Wrench (Chuck Removal).................................... ................................................. 1
89 .............6294212...................Lower Cylinder Fitting .......................................... ................................................. 1
90 .............6294213...................Wing Screw..........................................................M6 × 8...................................... 2
91 .............6294214...................Roll Pin................................................................. ................................................. 1
92 .............6294215...................Key.......................................................................5 × 5 × 10................................. 1
93 .............6294216...................Key.......................................................................5 × 5 × 12................................. 1
94 .............6294217...................Power Cord.......................................................... ................................................. 1
95 .............6294223...................Plastic Handle Sleeve.......................................... ................................................. 1
96 .............3005069...................Chuck Extension Adaptor .................................... ................................................. 1
97 .............JWP15-065 ..............Wing Screw..........................................................M6×25...................................... 2
98 .............TS-0267051 .............Socket Set Screw.................................................1/4-20 ×1/2............................... 2
99 .............TS-2361081 .............Lock Washer........................................................M8............................................ 2
100 ...........TS-2360121 .............Flat Washer..........................................................M12.......................................... 1
101 ...........TS-2361061 .............Lock Washer........................................................M6............................................ 3
102 ...........6294243...................Roll Pin.................................................................M6 × 16.................................... 1
103 ...........6294244...................Cord Strain Relief................................................. ................................................. 1
104 ...........719T-1104................Pin........................................................................ ................................................. 1
105 ...........719T-1105................Pointer.................................................................. ................................................. 1
106 ...........TS-1550041 .............Flat Washer..........................................................M6............................................ 1
107 ...........TS-1534032 .............Machine Screw, Pan Head, Phillips.....................M6 x 10.................................... 1
108 ...........719T-1108................Tilting Bracket ...................................................... ................................................. 1
109 ...........TS-155010 ...............Flat Washer..........................................................M16.......................................... 1
110 ...........719T-1110................Shaft..................................................................... ................................................. 1
111 ...........719T-1111................Square Nut........................................................... ................................................. 1
112 ...........TS-1490051 .............Hex Cap Screw....................................................M8 x 30.................................... 2
113 ...........TS-1540061 .............Hex Nut ................................................................M8............................................ 2
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Index No. Part No.
Description
Size
Qty
114 ...........TS-1491021 .............Hex Cap Screw....................................................M10 x 20.................................. 4
115 ...........719T-1115................Tilting Bracket ...................................................... ................................................. 1
116 ...........TS-2342161 .............Hex Nut, Nylon Lock ............................................M16.......................................... 2
117 ...........719T-1117................Wave Washer....................................................... ................................................. 2
118 ...........719T-1118................Bolt....................................................................... ................................................. 2
119 ...........719T-1119................Tilting Base .......................................................... ................................................. 1
120 ...........719T-1120................Box Wrench..........................................................23mm....................................... 1
719T Mortiser Assembly
18
Download from Www.Somanuals.com. All Manuals Search And Download.
719T Mortiser Stand Parts List
Index No. Part No.
Description
Size
Qty
.................6294235T.................Stand Assembly (Items 1 thru 8).......................... ................................................. 1
1 ...............719T-201..................Stand.................................................................... ................................................. 1
2 ...............719T-202..................Shelf Cushion....................................................... ................................................. 1
.................6294236...................Door Assembly (Items 3 thru 6)........................... ................................................. 1
3 ...............6294226...................Door ..................................................................... ................................................. 1
4 ...............6294227...................Pin........................................................................ ................................................. 2
5 ...............6294228...................Door Latch............................................................ ................................................. 1
6 ...............TS-2171012 .............Machine Screw, Pan Head, Phillips.....................M4 x 6 ...................................... 2
7 ...............TS-2361081 .............Lock Washer........................................................M8............................................ 4
8 ...............TS-1490081 .............Hex Cap Screw....................................................M8 × 45.................................... 4
719T Mortiser Stand Assembly
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Index No. Part No.
Description
.................6294232...................Chuck Extension Adaptor Kit (Items 1 thru 3)...... ...................................................
1 ...............6294210...................Drill Adaptor Shaft................................................ ...................................................
2 ...............6294208...................Chuck Release Nut.............................................. ...................................................
3 ...............6294209...................Spring Washer ..................................................... ...................................................
4 ...............6285526...................Chisel & Bit, 1/4" .................................................. ...................................................
5 ...............6285527...................Chisel & Bit, 5/16" ................................................ ...................................................
6 ...............6285528...................Chisel & Bit, 3/8" .................................................. ...................................................
7 ...............6285529...................Chisel & Bit, 1/2" .................................................. ...................................................
8 ...............6294245...................Chuck & Key, 1/2"................................................ ...................................................
9 ...............6294198...................Drill Bushing, 1-1/8" ............................................. ...................................................
10 .............6294221...................Drill Bushing, 3/4"................................................. ...................................................
11 .............6294222...................Drill Bushing, 5/8"................................................. ...................................................
WMH Tool Group
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|