Jet Tools Cordless Drill 20PF User Manual

This .pdf document is bookmarked

Operating Instructions and Parts Manual

Geared Head Drilling/Tapping Presses

Models GHD-20/20T/20PF/20PFT

Model GHD-20PFT shown

For models with serial no. 130701360 and higher

JET

427 New Sanford Road

LaVergne, Tennessee 37086

Part No. M-354026

Ph.: 800-274-6848

Revision I 05/2014

www.jettools.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Warranty and Service............................................................................................................................................2

Table of Contents..................................................................................................................................................3

Warning.................................................................................................................................................................4

Introduction ...........................................................................................................................................................6

Specifications........................................................................................................................................................6

Unpacking .............................................................................................................................................................7

Contents of the Shipping Container ..................................................................................................................7

Assembly...............................................................................................................................................................7

Adjusting the Head Height.................................................................................................................................8

Adjusting the Rack Assembly............................................................................................................................8

Controls.................................................................................................................................................................9

Control Panel for GHD-20T/20PFT .................................................................................................................10

Electrical Connections.........................................................................................................................................10

Adjustments ........................................................................................................................................................11

Installing a Drill Chuck (not included) ..............................................................................................................11

Removing the Arbor ........................................................................................................................................11

Adjusting the Depth Stop for Drilling (GHD-20)............................................................................................11

Adjusting Depth Stop for Drilling and Tapping (GHD-20T)..............................................................................11

Adjusting the Depth Stop for Drilling (GHD-20PF) ..........................................................................................12

Adjusting the Depth Stop for Drilling (GHD-20PFT)........................................................................................12

Adjusting the Depth Stop for Tapping (GHD-20PFT)......................................................................................12

Changing Spindle Speeds...............................................................................................................................12

Return Spring Adjustment ...............................................................................................................................13

Tilting the Head ...............................................................................................................................................13

Lubrication...........................................................................................................................................................13

Changing the Gear Box Lubricant ...................................................................................................................14

Replacement Parts..............................................................................................................................................16

GHD-20PF/20PFT Head Assembly.................................................................................................................17

Parts List – GHD-20PF/20PFT Head Assembly..............................................................................................18

GHD-20/20T Head Assembly..........................................................................................................................21

Parts List – GHD-20/20T Head Assembly.......................................................................................................22

Gear Assembly GHD-20PF, 20PFT ................................................................................................................24

Parts List – Gear Assembly GHD-20PF, 20PFT .............................................................................................25

Gear Assembly GHD-20/20T ..........................................................................................................................26

Parts List – Gear Assembly GHD-20/20T .......................................................................................................27

Base, Table and Column Assembly (all models).............................................................................................28

Parts List – Base, Table and Column Assembly (all models)..........................................................................29

Control Box Assembly (all models) .................................................................................................................30

Parts List – Control Box Assembly..................................................................................................................31

Electrical Panel Components (GHD-20PFT)...................................................................................................32

Parts List – Electrical Panel Components (GHD-20PFT)................................................................................33

Electrical Schematic (GHD-20/20PF only) ......................................................................................................34

Electrical Schematic (GHD-20PFT).................................................................................................................35

Electrical Schematic (GHD-20T) .....................................................................................................................36

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning

1. Read and understand the entire owner’s manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of

these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This drill press is designed and intended for use by properly trained and experienced personnel only. If you

are not familiar with the proper and safe operation of a drill press, do not use until proper training and

knowledge have been obtained.

5. Do not use this drill press for other than its intended use. If used for other purposes, JET disclaims any real

or implied warranty and holds itself harmless from any injury that may result from that use.

6. Do not use this machine in damp or wet locations, or expose it to rain. Keep work area well lighted.

7. Always wear approved safety glasses/face shields while using this drill press. (Everyday eyeglasses only

have impact resistant lenses; they are not safety glasses.)

8. Before operating this drill press, remove tie, rings, watches and other jewelry, and roll sleeves up past the

elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are

recommended. Do not wear gloves.

9. Wear ear protectors (plugs or muffs) during extended periods of operation.

10. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains

chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

•

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to

these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or

dust masks that are specifically designed to filter out microscopic particles.

11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

12. Make certain the switch is in the OFF position before connecting the machine to the power supply.

13. Clamp the workpiece or brace it against the column to prevent rotation.

14. Use the recommended speed for drill accessories and workpiece materials.

15. Make certain the machine is properly grounded.

16. Make all machine adjustments or maintenance with the machine unplugged from the power source.

17. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches

are removed from the machine before turning it on.

18. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes,

use extreme caution and replace the guards immediately after maintenance is complete.

19. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions

that may affect its operation. A guard or other part that is damaged should be properly repaired or

replaced.

20. Provide for adequate space surrounding work area and non-glare, overhead lighting.

21. Keep the floor around the machine clean and free of scrap material, oil and grease.

22. Keep visitors a safe distance from the work area. Keep children away.

23. Make your workshop child proof with padlocks, master switches or by removing starter keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

24. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

25. Maintain a balanced stance at all times so that you do not fall or lean against the rotating spindle or other

moving parts. Do not overreach or use excessive force to perform any machine operation.

26. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which

it was not designed. The right tool will do the job better and more safely.

27. Use recommended accessories; improper accessories may be hazardous.

28. Maintain tools with care. Keep cutting tools sharp and clean for the best and safest performance. Follow

instructions for lubricating and changing accessories.

29. Make sure the workpiece is securely attached or clamped to the table. Never use your hand to hold the

work piece.

30. Turn off the machine and disconnect from power before cleaning. Use a brush or compressed air to

remove chips or debris — do not use your hands.

31. Do not stand on the machine. Serious injury could occur if the machine tips over.

32. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

33. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious or even fatal

injury.

- - SAVE THESE INSTRUCTIONS - -

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

This manual is provided by JET covering the safe operation and maintenance procedures for JET Model GHD-

20 Series Drill Presses. This manual contains instructions on installation, safety precautions, general operating

procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed

to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there

are any questions or comments, please contact either your local supplier or JET. JET can also be reached at

our web site: www.jettools.com.

Specifications

Model Number .....................................................GHD-20...............GHD-20PF................... GHD-20T ............ GHD-20PFT

Stock Number ....................................................... 354020.....................354024.......................354022 .................... 354026

Drilling Capacity – Cast Iron (in.)..............................1-1/2.........................1-1/2.......................... 1-1/2 ........................ 1-1/2

Drilling Capacity – Mild Steel (in.).............................1-1/4.........................1-1/4.......................... 1-1/4 ........................ 1-1/4

Column Diameter (in.)...............................................4-1/2.........................4-1/2.......................... 4-1/2 ........................ 4-1/2

Quill Diameter (in.).......................................................... 3............................... 3.................................3 ...............................3

Swing (in.) ..................................................................... 20.............................20...............................20 ............................ 20

Number of Spindle Speeds........................................... 12.............................12...............................12 ............................ 12

Range of Spindle Speeds (RPM)............[all models] Low: 60/130/230/450/800/1500; High: 120/260/460/900/1600/3000

Number of Power Downfeeds...................................... n/a............................... 3..............................n/a ...............................3

Range of Power Downfeeds........................................ n/a....0.004, 0.007, 0.01..............................n/a ...0.004, 0.007, 0.01

Spindle Taper............................................................MT-3.........................MT-3.......................... MT-3 ........................MT-3

Spindle Travel, manual (in.)............................................ 5.........................4-1/2.................................5 ........................ 4-1/2

Spindle Travel, powerfeed (in.).................................... n/a.........................4-1/4..............................n/a ........................ 4-1/4

Maximum Distance Spindle to Table (in.) ..............30-1/2.......................30-1/2........................ 30-1/2 ...................... 30-1/2

Maximum Distance Spindle To Base (in.) ............44-5/16.....................44-5/16...................... 44-5/16 .................... 44-5/16

Table Size (in.)..........................................21-3/4 x 19-1/2........ 21-3/4 x 19-1/2.......... 21-3/4 x 19-1/2 ........21-3/4 x 19-1/2

Table Travel (in.).....................................................25-1/2.......................25-1/2........................ 25-1/2 ...................... 25-1/2

Table T-Slots................................................................... 2............................... 2.................................2 ...............................2

Table T-Slot Size (in.).................................................. 5/8............................5/8..............................5/8 ........................... 5/8

Table T-Slot Centers (in.) ............................................... 9............................... 9.................................9 ...............................9

Work Table Weight Capacity (lbs.)............................. 275...........................275.............................275 .......................... 275

Base Dimensions LxWxH (in.)........................ 26 x 18 x 5............... 26 x 18 x 5.................26 x 18 x 5 ...............26 x 18 x 5

Base Work Table (in.).....................................15-1/4 x 13...............15-1/4 x 13................ 15-1/4 x 13 .............. 15-1/4 x 13

Base T-Slots.................................................................... 2............................... 2.................................2 ...............................2

Base T-Slot Size (in.)................................................... 5/8............................5/8..............................5/8 ........................... 5/8

Motor ..................................................................................[all models] TEFC 2HP, 3PH, 230V only, 60Hz, 2-speed

Overall Dimensions LxWxH (in.)................... 32 x 24 x 71............. 32 x 24 x 71...............32 x 24 x 71 .............32 x 24 x 71

Net Weight (lbs.) ......................................................... 660...........................660.............................700 .......................... 700

The above specifications were current at the time this manual was published, but because of our policy of

continuous improvement, JET reserves the right to change specifications at any time and without prior notice,

without incurring obligations.

Download from Www.Somanuals.com. All Manuals Search And Download.

Unpacking

Contents of the Shipping Container

Gear Head Drill Press

Lug Wrench

Can of White Touch-Up Paint

Drill Chuck Arbor (MT-3 x JT-6)

Drawbar

Drift Key

Crank

Handle

Downfeed Handles (GHD-20/20T only)

Knobs (two with GHD-20PF/20PFT)

3mm Hex Wrench

4mm Hex Wrench

5mm Hex Wrench

Main Shaft Cover

Owner's Manual

Warranty Card

1. Finish removing the contents of the shipping

container.

2. Compare the contents of the shipping container with

the list above. Report any shortages or damage to

your JET distributor.

3. Clean all rust protected surfaces with kerosene or a

light solvent. Do not use lacquer thinner, paint

thinner or gasoline. These will damage plastic

components and painted surfaces.

Assembly

Figure 1

1. Slide crank (A, Figure 1) onto the table raising

assembly shaft.

2. Tighten the set screw (B, Figure 1) to hold the crank

in place

3. Install the handle (C, Figure 1) onto the crank

4. For the GHD-20/20T, install three handles with knobs

(A, Figure 2) into the downfeed hub. For the GHD-

20PF/20PFT, screw two knobs onto the handles of

the power downfeed assembly.

5. Install chuck guard by sliding the support bar up into

the base mounted to the head. Tighten screws.

Figure 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Head Height

To facilitate shipping, the Drill Press is packed with the

head adjusted down on the column. The head assembly

should be moved to the top of the column before drilling

operation starts.

The head assembly is very heavy.

Use caution when adjusting the head and make sure

it is supported by the table or locked in place. Failure

to comply may cause damage to property and/or

personal injury!

1. Unlock the table by loosening the handle (A, Figure

Figure 3

2. Lower the table until there is room to place a block of

wood between the table and the head assembly

(Figure 4).

3. Loosen two nuts (A, Figure 5) on the head assembly.

4. Raise the head by raising the table. The head is at

the correct height when the top of the head is just

below the column cap (B, Figure 5).

5. Tighten the two nuts (A, Figure 5) on the head

assembly firmly.

6. To lower the head, reverse the steps above. Do not

loosen the head assembly bolts without

supporting the head. This may cause the head to

slip on the column and may cause damage to the

machine or personal injury.

Figure 4

Adjusting the Rack Assembly

After the table has been adjusted, the rack assembly will

need to be raised.

The table must be locked when

raising the rack. Failure to lock the table may cause

the assembly to drop on the column, causing

damage to the machine.

1. Make sure both head assembly nuts (A, Figure 5)

are tight.

Figure 5

2. Loosen the hex socket cap screw (C, Figure 6) on

the upper rack ring.

3. Loosen two set screws on the bottom rack ring (D,

Figure 7).

4. Raise the rack assembly by turning the table raising

handle clockwise.

5. The rack assembly is at its full height when the top

rack ring is just below the head assembly (as

illustrated in Figure 6).

6. Tighten the hex socket cap screw on the top rack

ring and two set screws on the lower rack ring.

Figure 6

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls

Low/Off/High Switch (A, Figure 8) – located top left side

of the head assembly. Switch between low and high

speed range. In the stop position, the spindle is stopped,

but the machine still has power.

Fine Feed Handwheel (B, Figure 8) – located on the

front lower right of the head assembly. Turn clockwise to

lower the quill. Turn counter-clockwise to raise the quill.

Figure 7

Figure 8

Figure 9

Quill Lock (C, Figure 8) – located on the front lower right

of the head assembly. Turn clockwise and tighten to lock

the quill. Turn counterclockwise and loosen to unlock the

quill.

Speed Selectors (D, Figure 8) – located on the top front

of the head assembly. Used with low/off/high switch and

the speed chart on the front of the head assembly to set

the drill to a specific speed. Caution: Change speeds

only when the machine is stopped.

Depth Stop (GHD-20/20T) (E, Figure 8) - located on the

front bottom of the head assembly. When set, the quill

will only advance to a certain depth.

Depth Stop (GHD-20PF/20PFT) (A, Figure 9) - located

on the downfeed assembly on the right side of the head

assembly. When set, the quill will advance automatically

or manually to a certain depth.

Power Downfeed Speed Selector (GHD-20PF/ 20PFT)

(B, Figure 9) - located on the right side of the head

assembly. Set to advance the quill at desired speed.

Engage the power downfeed by pulling the handle

assembly away from the head. Disengage the power

downfeed by pushing the handle assembly toward the

head. Tighten Lock Screw (C, Figure 9) to lock out the

power downfeed and to keep the drill in manual feed

only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Panel for GHD-20T/20PFT

Low/Off/High Switch (A, Figure 9A) Switch between low

and high speed range. In the stop position, the spindle is

stopped, but the machine still has power.

Drilling Tapping Selector (B, Figure 9A) For drilling,

press the start switch (F, Figure 9A) to run the machine.

Caution: The internal depth stop (GHD-20PFT) is used

only with the tapping function. Raise the adjusting knob

(B, Figure 11) to the top of the depth stop screw so as

not to interfere with power downfeed or manual feeding

operations. For tapping, turn switch (B, Figure 9A) to

tapping position, press down the handle. The quill

functions when upper limit switch is released. It then

reverses automatically after hitting lower limit switch and

will not stop until it hits the upper limit switch.

Figure 9A

Emergency Switch (C, Figure 9A) Press this switch to

stop all operations.

Power Light (D, Figure 9A) Indicates power is on.

Reverse Switch (E, Figure 9A) If tapping is interrupted

press the reverse switch to reverse the tap from

workpiece. The button must be held down for continuous

reversing.

Start Switch (F, Figure 9A) Activates the motor in the

drill or tap mode.

Electrical Connections

Electrical connections must be

made by a qualified electrician in compliance with all

relevant codes. This machine must be properly

grounded to help prevent electrical shock and

possible fatal injury. All adjustments or repairs must

be done with the drill disconnected from the power

source.

The motor is rated at 2 HP, 3 PH, 230V only. Make sure

the power available matches the power requirement of

the drill. The drill must be properly grounded.

When the drill is connected properly, the spindle turns

clockwise in a conventional drilling rotation. If the spindle

does not turn clockwise, disconnect the drill from the

power supply and reverse two of the three power leads.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjustments

Installing a Drill Chuck (not included)

1. Disconnect the machine from the power source.

2. Clean the arbor and the inside of the chuck. The

tapers must be clean and dry.

3. Push the chuck onto the arbor.

4. Retract the chuck jaws completely, and push the

arbor into the spindle.

5. Use a rubber mallet, or steel face hammer against a

block of wood, to sharply tap the bottom of the chuck

two or three times to seat it. (Note: Never use a steel

face hammer directly against the chuck.)

Removing the Arbor

1. Unplug the machine from the power source.

2. Make sure the drill is in gear.

3. Remove the main shaft cover (A, Figure 11).

4. Use an adjustable wrench or box wrench to loosen

the draw bar (A, Figure 10).

5. Unscrew the draw bar approximately two revolutions.

If the arbor is not loose, gently tap on top of the draw

bar to loosen the arbor.

Figure 10

6. Continue to unscrew the draw bar with one hand on

the chuck and arbor so that it doesn’t drop onto the

table.

Adjusting the Depth Stop for Drilling

(GHD-20)

To drill multiple holes at the same preset depth, use the

depth stop:

1. Turn the adjusting knob (B, Figure 11) until the

correct depth is indicated on the scale on the front of

the drill head.

2. Drill several test holes to make sure the depth stop is

set correctly.

Adjusting Depth Stop for Drilling and

Tapping (GHD-20T)

1. Follow steps for GHD-20 drilling.

Figure 11

2. When the tapping switch is on, the limit switches are

active and will reverse rotation at the bottom of the

stroke and stop rotation at the top.

3. When the tapping switch is off, the limit switches are

inactive and do not effect spindle rotation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Depth Stop for Drilling

(GHD-20PF)

1. Loosen the depth stop lock handle (A, Figure 12).

2. Manually advance the quill to the desired depth with

one hand.

3. With the other hand, turn the depth stop scale (B,

Figure 12) counter-clockwise to zero.

4. Tighten the depth stop lock handle (A, Figure 12).

The depth stop will now stop the drill at the pre-

determined setting.

Adjusting the Depth Stop for Drilling

(GHD-20PFT)

1. Turn the adjusting knob (B, Figure 11) until full travel

is possible. Do not use this scale as a reference

when drilling. This depth stop is for tapping only and

should not interfere with drilling operations.

Figure 12

2. Follow steps for GHD-20PF drilling.

Adjusting the Depth Stop for Tapping

(GHD-20PFT)

1. Loosen the depth stop lock handle (A, Figure 12) so

that it does not interfere with the internal depth stop

located on the front of the drill head.

2. Adjust the front depth stop for the proper depth.

3. Manually advance the quill releasing the upper limit

switch for tapping. This will start the motor. The quill

will reverse directions upon triggering the lower limit

switch.

4. Do not powerfeed and tap at the same time.

Changing Spindle Speeds

To change spindle speeds:

1. Stop the drill by turning the low/stop/high switch to

stop.

2. Adjust the levers (A, Figure 13) to the desired speed

as indicated by the speed chart. Turning the spindle

by hand will help the gear teeth mesh.

Figure 13

Download from Www.Somanuals.com. All Manuals Search And Download.

Return Spring Adjustment

The return spring is adjusted at the factory and should

not need further adjustment. If adjustment ever becomes

necessary:

1. Unplug the machine from the power source.

2. Loosen lock knob (A, Figure 14) while holding the

quill spring cover. Do not allow the cover to turn in

your hand or the spring will unwind.

3. Pull out the cover (B, Figure 14) and rotate until the

pin (C, Figure 14) on the return spring plate engages

the next notch in the coil spring cover. Turn the cover

clockwise to decrease tension and counter-clockwise

to increase tension.

Figure 14

4. Tighten the lock knob (A, Figure 14). Do not over-

tighten. Nuts should not contact the housing when

tight.

Tilting the Head

To tilt the head:

1. Turn nut (A, Figure 15) clockwise to pull out the

alignment pin (B, Figure 15).

2. Loosen hex nuts (C, Figure 15).

3. Tilt the head to the desired angle.

4. Tighten two hex nuts (C, Figure 15).

5. The alignment pin only works at 0° and must be

reinserted when the head is returned to 0°.

Figure 15

Lubrication

Refer to Figure 16.

1. Headstock. Fill with Mobil DTE® Oil Heavy Medium.

Check level daily and change yearly.

2. Powerfeed. Use Mobilith AW2 every three months.

3. Spline Drive. Use Mobilith AW2 every three months.

4. Quill Pinion Gear. Use Mobilith AW2 Every three

months.

5. Quill Column Surface. Use Mobil DTE® Oil Heavy

Medium every three months.

6. Table Pinion Gear. Use Mobilith AW2 every three

months.

7. Quill Return Spring. Mobil DTE® Oil Heavy

Medium every month. Do not remove cover.

Figure 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the Gear Box Lubricant

1. Disconnect the machine from the power source.

2. Loosen nuts (A, Figure 17).

3. Tilt the head to access the drain plug. The drain plug

is found in the head cavity behind the spindle.

4. Loosen the drain plug but do not remove.

5. Return the head to upright position.

6. Place a container on the table to catch the draining

lubricant.

7. Remove the filler plug (A, Figure 18).

8. Remove the drain plug.

Figure 17

9. Replace the drain plug after the lubricant has

finished draining.

10. Pour one (1) gallon of new lubricant (SHC-634 Oil

Heavy Medium) through the filler hole. Caution:

Use of any other type of lubricant other than that

specified may cause damage to the drill press.

11. Replace the filler plug.

Figure 18

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Trouble

Probable Cause

Remedy

Excessive vibration.

Motor out of balance.

Balance motor or replace.

Adjust quill.

Improper quill adjustment.

Lubricate spindle. See the Lubrication

section.

Dry spindle.

Noisy motor

Noisy Operation.

Check motor bearings or for a loose

motor fan.

Overfeeding.

Dull drill bit.

Reduce feed rate.

Sharpen drill bit.

Motor Stalls.

Replace or repair motor. Check fuses in

all three legs on three phase motors

and replace, if necessary.

Motor not running up to speed.

Excessive speed.

Dull tool.

Reduce speed.

Sharpen tool or replace.

Increase feed enough to clear chips.

Reverse motor rotation.

Drill or tool heats up or Feed rate too slow.

burns work.

Rotation of drill incorrect.

Failure to use cutting oil or coolant (on

steel).

Use cutting oil or coolant (on steel).

No drill spot.

Center punch or center drill workpiece.

Re-grind drill.

Cutting lips on drill off center.

Quill loose in head.

Bearing play.

Drill leads off.

Tighten quill.

Reseat or replace bearings.

Replace drill.

Bent drill.

Excessive drill runout

or wobble.

Bearing play.

Reseat or replace bearings.

Loosen, reset, and tighten chuck.

Drill not seated properly in the chuck.

Work or fixture comes

loose or spins.

Failure to clamp work piece or work

holding device to table.

Clamp work piece or work holding

device to the table surface.

Download from Www.Somanuals.com. All Manuals Search And Download.

Replacement Parts

Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-

800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com). Having the

Model Number and Serial Number of your machine available when you call will allow us to serve you quickly

and accurately.

Download from Www.Somanuals.com. All Manuals Search And Download.

GHD-20PF/20PFT Head Assembly

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts List – GHD-20PF/20PFT Head Assembly

Index No. Part No.

Description

Size

Qty

40 ..............GHD20PF-40 ............ Screw....................................................................... 3/16” x 3/8”....................1

42 ..............61105 ........................ Spring Base ............................................................. ......................................1

43 ..............GHD20PF-43 ............ Spring Pin................................................................ 3 x 12 mm.....................2

44 ..............GHD20PF-44 ............ Screw....................................................................... 3/16” x 3/4”....................3

45 ..............61104 ........................ Spring ...................................................................... ......................................1

46 ..............61103 ........................ Spring Cover............................................................ ......................................1

47 ..............TS-0680021 .............. Washer .................................................................... 1/4"................................1

48 ..............TS-0720071 .............. Lock Washer............................................................ 1/4"................................1

49 ..............6185 .......................... Lock Knob................................................................ ......................................1

50-A...........GHD20-50-A ............. Chuck Guard Assembly (#50-1 thru 50-9)............... ......................................1

50-1...........JMD18-125-1 ............ Chuck Guard............................................................ ......................................1

50-2...........JMD18-125-2 ............ Chuck Guard Supporting Rod.................................. ......................................1

50-3...........TS-2361051 .............. Spring Washer......................................................... M5.................................4

50-4...........TS-1502021 .............. Hex Socket Head Screw.......................................... M5 x 10 .........................2

50-5...........GHD20-50-5.............. Chuck Guard Bracket .............................................. ......................................1

50-6...........JMD18-125-5 ............ Rotary Supporting Base........................................... ......................................1

50-7...........JMD18-125-6 ............ Hex Socket Cap Screw............................................ M5x15L .........................2

50-8...........TS-1551041 .............. Spring Washer......................................................... M6.................................2

50-9...........6286490 .................... Hex Socket Cap Screw............................................ M6x15L .........................2

52 ..............TS-0071141 .............. Hex Cap Bolt............................................................ 5/8” x 5-1/2”...................2

53 ..............GHD20-53................. Oil Plug .................................................................... 1/4”PT...........................1

70 ..............2421003 .................... Handle Rod.............................................................. ......................................1

76 ..............2401076 .................... Scale........................................................................ ......................................1

76-1...........2450060 .................... Pointer ..................................................................... ......................................3

78 ..............6112 .......................... Rubber Gasket......................................................... ......................................1

79 ..............2412001 .................... Casting..................................................................... ......................................1

82 ..............6114 .......................... Lock Nut................................................................... ......................................1

83 ..............GHD20PF-83 ............ Star Washer............................................................. ......................................1

84 ..............BB-30206.................. Taper Roller Bearing................................................ ......................................1

85 ..............6116 .......................... Rack Sleeve............................................................. MT3...............................1

86 ..............6117 .......................... Spindle Shaft ........................................................... ......................................1

87 ..............BB-30207.................. Taper Roller Bearing................................................ ......................................1

88 ..............6119 .......................... Bearing Cap............................................................. ......................................1

89 ..............6127 .......................... Screw Key................................................................ ......................................1

90 ..............TS-0561031 .............. Hex Nut.................................................................... 3/8”................................1

91 ..............2401066 .................... Gear Lever Bracket.................................................. ......................................2

92 ..............2401067 .................... Gear Lever (Left) ..................................................... ......................................1

93 ..............2401068 .................... Gear Lever (Right)................................................... ......................................1

94 ..............GHD20PF-94 ............ Screw....................................................................... 1/4” x 1/2"......................1

95 ..............2401070 .................... Lever Shaft (Right)................................................... ......................................1

96 ..............2401071 .................... Lever Shaft (Left)..................................................... ......................................1

97 ..............GHD20PF-97 ............ C-Ring...................................................................... ......................................2

98 ..............GHD20PF-98 ............ Oil Sight Glass......................................................... ......................................1

99 ..............GHD20PF-99 ............ Screw....................................................................... 3/16” x 3/8”....................8

100 ............GHD20PF-100 .......... Oil Seal.................................................................... G12...............................2

102 ............2401075 .................... Speed Lever ............................................................ ......................................2

106 ............GHD20PF-106 .......... Oil Plug .................................................................... ......................................1

107 ............TS-0209081 .............. Hex Socket Cap Screw............................................ 3/8” x 3/4"......................6

108 ............GHD20PF-108 .......... Miter Pin................................................................... ......................................2

109 ............TS-0267021 .............. Set Screw ................................................................ 1/4" x 1/4"......................4

110 ............GHD20-86................. Motor........................................................................ 2HP 3PH 230V..............1

111 ............GHD20PF-111 .......... Key........................................................................... 6 x 5 x 30mm ................1

112 ............TS-0209051 .............. Hex Socket Cap Screw............................................ 3/8” x 3/4”......................6

113 ............GHD20-89................. Brass Fitting............................................................. ......................................1

114 ............TS-0561071 .............. Hex Nut.................................................................... 5/8”................................3

116 ............TS-0071041 .............. Hex Cap Bolt............................................................ 5/8” x 2-1/4”...................3

119 ............6126-1....................... Collar (thread).......................................................... ......................................1

120 ............6125-1....................... Collar ....................................................................... ......................................1

121 ............6125-2....................... Collar ....................................................................... ......................................1

122 ............61112 ........................ Cover Plate.............................................................. ......................................1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index No. Part No.

Description

Size

Qty

123 ............GHD20-123............... Screw....................................................................... ......................................4

124 ............GHD20-124............... Lamp Assembly....................................................... ......................................1

125 ............TS-2284352 .............. Pan Head Screw...................................................... M4x35L .........................2

126 ............GHD20-126............... Lamp Base............................................................... ......................................1

127 ............TS-1503031 .............. Hex Socket Cap Screw............................................ M6x12L .........................2

150 ............TS-0561071 .............. Hex Nut.................................................................... 5/8”................................2

151 ............TS-0680081 .............. Washer .................................................................... 5/8”................................2

201 ............2450001 .................... Head Body Cover .................................................... ......................................1

202 ............2450002 .................... Head Body Casting.................................................. ......................................1

218 ............2450008 .................... Worm Gear.............................................................. ......................................1

219 ............TS-1523011 .............. Set Screw ................................................................ M6 x 6 ...........................4

220 ............GHD20PF-220 .......... C-Ring...................................................................... ......................................4

227 ............2450014 .................... Cover ....................................................................... ......................................1

233 ............GHD20PF-233 .......... Screw....................................................................... M4 x 25 .........................1

235 ............2450020 .................... Release Block.......................................................... ......................................1

236 ............2450021 .................... Small Pinion Shaft ................................................... ......................................1

237 ............2450022 .................... Key........................................................................... ......................................2

238 ............2450023 .................... Worm Gear.............................................................. ......................................1

239 ............2450024 .................... Clutch Key Base ...................................................... ......................................1

241 ............2450026 .................... Clutch Key ............................................................... ......................................2

242 ............2450027 .................... Spring Pin................................................................ ......................................2

243 ............2450028 .................... Spring ...................................................................... ......................................2

244 ............GHD20PF-244 .......... C-Ring...................................................................... ......................................1

246 ............2450030 .................... Bushing Pin.............................................................. ......................................1

247 ............2450031 .................... Bushing Stop ........................................................... ......................................1

248 ............2450032 .................... Scale Base............................................................... ......................................1

249 ............GHD20PF-249 .......... Rivet......................................................................... ......................................8

250 ............2450033 .................... Scale Base Set Screw............................................. ......................................1

254 ............2450037 .................... Handle Body............................................................ ......................................1

255 ............2450038 .................... Handle Rod.............................................................. ......................................2

256 ............GHD20PF-256 .......... Knob ........................................................................ ......................................2

257 ............2450039 .................... Handle Rod Pin........................................................ ......................................2

258 ............2450040 .................... Washer .................................................................... ......................................1

259 ............TS-1504021 .............. Hex Socket Cap Screw............................................ M8 x 12 .........................1

265 ............GHD20PF-265 .......... Key........................................................................... 5 x 5 x 32mm ................1

266 ............2450045 .................... Cover ....................................................................... ......................................1

268 ............TS-1502031 .............. Hex Socket Cap Screw............................................ M5 x 12 .........................2

269 ............GHD20PF-269 .......... Key........................................................................... 4 x 4 x 10mm ................1

270 ............24500470 .................. Handwheel............................................................... ......................................1

271 ............GHD20PF-271 .......... Washer .................................................................... ......................................1

272 ............TS-1523031 .............. Hex Socket Cap Screw............................................ M6 x 12 .........................1

279 ............TS-0561021 .............. Hex Nut.................................................................... 5/16”..............................1

282 ............GHD20PF-282 .......... Plug.......................................................................... 7/8”................................1

283 ............GHD20PF-283 .......... Oil Seal.................................................................... ......................................1

287 ............GHD20PF-287 .......... Spring Pin................................................................ ......................................2

291 ............2450051 .................... Pin............................................................................ ......................................1

313 ............2450063 .................... Grip.......................................................................... ......................................1

315 ............GHD20PF-315 .......... Washer .................................................................... 3/16”..............................2

330 ............2401085 .................... Dust Plate ................................................................ ......................................1

332 ............GHD20PF-332 .......... Pin............................................................................ ......................................1

333 ............2450069 .................... Dust Plate ................................................................ ......................................1

339 ............GHD20-339............... High-Low Switch (for GHD20PF only) ..................... ......................................1

340 ............GHD20-340............... Screw (GHD-20PF only).......................................... ......................................1

341 ............GHD20-341............... Motor Cord............................................................... ......................................1

342 ............GHD20-342............... Power Cord.............................................................. ......................................1

345 ............GHD20PF-345 .......... Nut ........................................................................... ......................................1

346 ............GHD20PF-346 .......... Manual Feed Knob .................................................. ......................................1

347 ............GHD20-347............... Name Plate.............................................................. ......................................1

347-1.........GHD20PF-347-1 ....... Name Plate (for GHD20PFT only - not shown) ....... ......................................1

348 ............2450086A.................. Pinion Shaft ............................................................. ......................................1

349 ............2450097 .................... Spring Pin................................................................ ......................................2

350 ............2450096 .................... Clutch Screw............................................................ ......................................1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index No. Part No.

Description

Size

Qty

351 ............2450095 .................... Clutch Nut................................................................ ......................................1

352 ............2450068 .................... Gear Box.................................................................. ......................................1

353 ............2450081A.................. Gear Shaft ............................................................... ......................................1

354 ............2450082A.................. Speed Change Lever............................................... ......................................1

355 ............2450083A.................. Stop ......................................................................... ......................................1

356 ............2450084A.................. Spring Leaf .............................................................. ......................................1

357 ............GHD20PF-357 .......... Pin............................................................................ ......................................2

358 ............2450089A.................. Bushing Bracket....................................................... ......................................1

359 ............2450072A.................. Bearing Bushing ...................................................... ......................................1

360 ............2450071A.................. Bearing Bushing ...................................................... ......................................1

361 ............2450070A.................. Bearing Bushing ...................................................... ......................................1

362 ............2450074A.................. Washer .................................................................... ......................................4

363 ............2450073A.................. Shaft ........................................................................ ......................................1

364 ............2450078A.................. Transmission Worm................................................. ......................................1

365 ............2450075A.................. Bearing Bushing ...................................................... ......................................1

366 ............2450076A.................. Bearing Bushing ...................................................... ......................................1

367 ............2450077A.................. Bearing Bushing ...................................................... ......................................1

368 ............2450085A.................. Spacer Ring............................................................. ......................................1

369 ............2450079 .................... Speed Lever ............................................................ ......................................1

370 ............GHD20PF-370 .......... Speed Scale ............................................................ ......................................1

371 ............290089 ...................... Spring ...................................................................... ......................................1

372 ............GHD20PF-372 .......... Steel Ball.................................................................. ......................................1

373 ............2450087A.................. Clutch Bushing......................................................... ......................................1

374 ............GHD20-374............... Flat Washer ............................................................. 1/2” x 7/8” x 2”...............1

375 ............2450100 .................... Washer .................................................................... ......................................1

376 ............GHD20PF-376 .......... E-Retainer Ring ....................................................... E5..................................2

377 ............GHD20PF-377 .......... Hex Socket Head Screw.......................................... 5/16” x 1-1/4”L...............4

378 ............CA6003ZZ................. Ball Bearing ............................................................. ......................................4

379 ............GHD20PF-379 .......... Key........................................................................... 5 x 5 x 28L mm .............1

380 ............GHD20PF-380 .......... C-Ring...................................................................... ......................................1

381 ............2450088A.................. Graduated Bottom Ring........................................... ......................................1

Download from Www.Somanuals.com. All Manuals Search And Download.

GHD-20/20T Head Assembly

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts List – GHD-20/20T Head Assembly

Index No. Part No.

Description

Size

Qty

11 ..............2401011 .................... Head Casting........................................................... ......................................1

12 ..............6112 .......................... Rubber Gasket......................................................... ......................................1

13 ..............6513 .......................... Feed Base ............................................................... ......................................1

14 ..............6114 .......................... Lock Nut................................................................... ......................................2

15 ..............BB-30206.................. Taper Roller Bearing................................................ ......................................1

16 ..............6116 .......................... Rack Sleeve............................................................. MT3...............................1

17 ..............6117 .......................... Spindle Shaft ........................................................... MT3...............................1

18 ..............BB-30207.................. Taper Roller Bearing................................................ ......................................1

19 ..............6119 .......................... Bearing Cap............................................................. ......................................1

24 ..............2421003 .................... Handle Rod.............................................................. ......................................1

27 ..............6127 .......................... Screw Key................................................................ ......................................1

35 ..............6135 .......................... Bearing Spacer........................................................ ......................................1

39 ..............6139 .......................... Handle Rod.............................................................. ......................................3

40 ..............290086 ...................... Knob ........................................................................ ......................................3

44 ..............6144 .......................... Micro Adjusting Indicator ......................................... ......................................1

45 ..............6145 .......................... Worm Cover............................................................. ......................................1

46 ..............BB-6202Z.................. Ball Bearing ............................................................. ......................................2

47 ..............6147 .......................... Worm Shaft.............................................................. ......................................1