©1976, 2008 SANRIO CO., LTD.
AM/FM STEREO CD CASSETTE RECORDER
OWNER’S MANUAL
KT2028A
THIS IS NOT A TOY
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
APPAREIL LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power laser device.
Follow the advice below for safe operations.
ON PROTECTION AGAINST LASER ENERGY EXPOSURE
·
·
·
·
·
As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the casing.
Stop operation immediately if any liquid or solid object should fall into the cabinet.
Do not touch the lens or poke at it. If you do, you may damage the lens and the player may not operate properly.
Do not put anything in the safety slot. If you do, the laser diode will be “ON” when the CD door is still open.
If the unit is not to be used for a long period of time, make sure that all power sources are disconnected from
the unit. Remove all batteries from the battery compartment, and unplug the AC cord from the wall outlet.
Make it a practice to remove the AC cord by grasping the main body and not by pulling the cord.
This unit employs a laser. The use of controls or adjustment or performance of procedures other than those
specified here may result in exposure to hazardous radiation.
·
ON PLACEMENT
·
·
·
Do not use the unit in places which are extremely hot, cold, dusty or humid.
Place the unit on a flat and even surface.
Do not restrict the air-flow of the unit by placing it in a place with poor ventilation, by covering it with a cloth or
by placing it on a carpet.
ON CONDENSATION
·
·
·
When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit.
When there is condensation inside the unit, the unit may not function normally.
Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
Should any trouble occur, remove the power source and refer servicing to qualified personnel.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONS AND CONTROLS
1. TELESCOPIC ANTENNA
2. CD COMPARTMENT LID
3. CD OPEN BUTTON
16. CD PROGRAM BUTTON
17. AC INPUT SOCKET (AC IN~)
18. AUX IN JACK
4. DIAL LENS
19. FUNCTION/POWER SWITCH
20. VOLUME CONTROL
21. BAND SELECTOR
22. TUNING CONTROL
23. BATTERY COMPARTMENT
24. PAUSE BUTTON
5. CD PLAY/PAUSE BUTTON
6. CASSETTE COMPARTMENT
7. CD SKIP BACKWARD BUTTON
8. REPEAT INDICATOR (REPEAT)
9. PLAY INDICATOR (PLAY
)
10. CD SKIP FORWARD BUTTON
11. CD REPEAT BUTTON
12. CD STOP BUTTON
25. STOP/EJECT BUTTON
26. FAST FORWARD BUTTON
27. REWIND BUTTON
13. PROGRAM INDICATOR (PROGRAM)
14. LCD DISPLAY
28. PLAY BUTTON
29. RECORD BUTTON
15. REPEAT ALL INDICATOR (ALL)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SOURCE
This AM/FM STEREO CD Cassette Recorder operates on 8 x ‘LR14’ (‘C’) batteries (not included) or
from AC 120V~ 60Hz line power supply.
A. BATTERY OPERATION
1. Remove the Battery Door.
2. Following the polarity diagram as shown in the battery compartment insert 8 x ‘LR14’ (‘C')
batteries then replace the Battery Door.
IMPORTANT : Be sure that the batteries are installed correctly. Wrong polarity may damage the
unit.
3. Use only the size and type of batteries specified.
4. For better performance and longer operating time, we recommend the use of alkaline-type
batteries.
5. Do not mix old and new batteries.
6. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
7. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking
batteries can cause damage to the unit and may void the warranty.
8. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions).
9. Do not dispose of batteries in fire, batteries may leak or explode.
B. AC OPERATION
When the AC power cord (included) is connected to the AC INPUT Socket (# 17) at the back of
the unit and the other end to a wall outlet with AC 120V ~ 60Hz power supply, the unit will
disconnect the batteries automatically, and operate from AC power instead.
Note: plug is used as the disconnect device. The disconnect device shall remain readily operable.
IMPORTANT :
This unit has a polarized AC plug with one wide blade and one narrow blade. This plug will only
fit into a matching polarized AC outlet. This is a safety feature to reduce the possibility of electric
shock. If this plug will not fit in your AC outlet, you probably have an outdated non-polarized
outlet. You should have your out-dated outlet changed by a qualified, licensed electrician. Do
not file the wide blade on the plug, or use an adaptor to make the plug fit onto your outlet. This
defeats the safety feature and could expose you to electric shock.
AC Outlet
AC Plug
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CD PLAYER OPERATION
Note: This player not only plays commercial CDs but also plays self-compiled CD-R/RW discs.
1. Set the Function/ Power Switch (# 19) to "CD" position. The player will display “- -”.
2. Open the CD LID by pressing the CD OPEN Button (# 3). Carefully place an audio CD,
with its label side upward, in the CD compartment and close the CD Door.
3. The total number of tracks on the CD will appear in the LCD Display (# 14) after
a few seconds.
4. Press the CD PLAY/PAUSE
Button (# 5). The CD PLAY Indicator “PLAY
”
will light and the CD will start playing from the first track.
5. Adjust the Volume Control (# 20) to obtain the desired sound level from
the Built-in Speakers.
6. To suspend playing, press the CD PLAY/PAUSE
The CD PLAY Indicator “PLAY ” will flash.
To resume playing, press the CD PLAY/PAUSE
Button (# 5).
Button (# 5) again.
7. You can choose to play your favorite track directly by pressing either the CD Skip Forward
Button (#10) or CD Skip Backward Button (#7).
The LCD Display (#14) will indicate the correct track number selected.
8. To locate a particular passage within a track, keep the CD Search Forward
Button (#10) or
CD Search Back ward
Button (#7) depressed until it is found.
9. To repeat a particular track, press the CD REPEAT Button (# 11) once or until the CD REPEAT
Indicator “REPEAT” (# 8) lights.
10.To repeat the entire CD, press the CD REPEAT Button (# 11) twice or until the CD REPEAT
Indicator “REPEAT ALL” (# 8,15) lights.
11. To stop playing, press the CD STOP
Button (# 12).
12.When you wish to turn off the CD PLAYER, set the Function/Power Switch (# 19) to "TAPE".
CD PROGRAMMED PLAY
This function allows the tracks to be played in a programmed sequence.
1. In CD stop mode, press the PROGRAM Button (#16) once. The CD PROGRAM
Indicator “PROGRAM” (# 13) will flash and “00” will appear and blink in the
LCD Display (# 14) to prompt for input.
2. Press the CD Skip BACKWARD Button
(#7) or CD Skip FORWARD Button
(#10) to select the song to be programmed. For example track 8 is selected.
3. Press the PROGRAM Button (# 16) again to store the selection. The Program
Channel No. will change to “00” and blink to prompt for Input.
4. Press the CD Skip Forward Button
(#10) or CD Skip Backward Button
(#7)
to select the next song to be programmed and press the PROGRAM Button (#16) to
store the selection. For example second selection is track 15.
5. You may repeat steps 2 - 4 to program as many as 20 tracks.
The LCD Display (#14) will display “- -” after programming 20 tracks.
6. Press the CD PLAY/PAUSE
Button (# 5) to start playing in the programmed
sequence. The PLAY lndicator "PLAY
" appears with the PROGRAM lndicator,
"PROGRAM", flashing in the Display.
7. Adjust the Volume Control (# 20) to obtain the desired sound level from the Built-in
Speakers.
8. To resume to normal playback, in CD Stop mode press the PLAY/PAUSE
9. When you wish to turn off the CD PLAYER, set the Function /Power Switch (# 19) to the
"TAPE" position.
Button (#5) again.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on CD-R/RW discs
-
Because of non-standardized format definition/ production of CD-R/RW,
playback quality and performance are not guaranteed.
-
Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions,
such as PC performance, writing software, media ability, etc.
-
-
Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
It is recommended to record only audio files on CD-R/RW discs for easy reading.
RADIO RECEPTION
1. Set the Function /Power Switch (# 19) to the "RADIO" position.
2. Set the Band Selector (# 21) to "AM" or “FM ST” for the desired radio band.
3. Turn the Tuning Control (# 22) to tune to your desired radio station.
4. Adjust the Volume Control (# 20) to obtain the desired sound level.
5. To turn the Radio off, set the Function /Power Switch (# 19) to the “TAPE” position.
TIPS FOR BEST RADIO RECEPTION
1. To insure maximum FM tuner sensitivity, the Telescopic Antenna (#1) should be fully extended
and rotated to obtain the best possible reception.
2. When tuning in AM reception, to insure best AM sensitivity, try repositioning the unit until the best
reception is obtained.
CASSETTE RECORDER OPERATION
1. Set the Function /Power Switch (# 19) to the "TAPE" position.
2. Open the Cassette Door (# 6) by pressing the STOP/EJECT Button (# 25) and insert a
pre-recorded cassette tape with the exposed tape facing upwards. Close the Cassette Door.
3. Press the Cassette Play Button (# 28) and adjust the Volume Control (# 20) to obtain the
desired sound level.
4. Press the Cassette Pause Button (# 24) to suspend play. Press the same button again to resume.
5. Press the Cassette F. FWD
advance or rewind the tape.
Button (# 26) or the Cassette REW
Button (# 27) to rapidly
6. Press the Cassette Record Button (# 29) to record either from the Radio or CD.
Use the Function /Power Switch (# 19) to choose your signal source accordingly.
7. Press the STOP/EJECT Button
(# 25) to stop operation.
AUTOMATIC STOP
To protect your cassette tapes and prevent unnecessary wear to the pinch rollrt of the cassette
mechanism,this unit is equipped with an Automatic Stop System. When the tape ends during play,the
Cassette Play Button (#28) will automatically release to stop the cassette from running.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CASSETTE TAPE OPERATING TIPS
1. High quality tapes are recommended to obtain maximum quality reproduction from recordings.
2. Tapes with playing time of 120 minutes (C-120) are not recommended because they contain
thinner and longer tape that has a greater chance to malfunction and jam, which may damage
the cassette mechanism.
3. To obtain good reproduction, the head should be cleaned after every 10 to 20 hours of use.
It is also recommended that the cassette be kept away from excessive heat or cold.
4. If there is slack in the tape, remove the slack prior to inserting the cassette. To remove the slack,
insert a pencil into the hub and rotate clockwise as shown below:
Tape Supply Reel
Tape Take-up Reel
5. A leader tape is provided at the beginning on each cassette. There is no recording on this area,
so it is necessary to let the tape run for about five seconds to clear the head.
6. Keep the tape head clean since a dirty head can cause distorted sound or improper tape speed.
Depress the Cassette Play Button (# 28) and use a small cotton swab with tape head cleaner or
alcohol to clean the tape head, capstan and pinch roller as shown below:
Pinch Roller
Capstan
Playback Head
AUX IN OPERATION
This CD Player provides the AUX IN JACK to enjoy your i-Pod, MP3 PLAYER MUSIC.
1. Connect the headphone jack of your external device and the AUX IN jack (18) located on the back
of this CD player. (The connection cable is not included.)
2. Turn on the CD player and it will enter the AUX function mode once the AUX IN jack is plugged.
3. Start to play your i-pod, MP3 player or other audio device.
4. Slowly adjust both the volume controls on your CD player and the external device.
5. Turn off your i-pod, MP3 player etc. when finish listening. Turn the CD player off and unplug the
AUX IN jack.
Remark: Once the AUX IN jack is plugged, the CD player will enter the AUX mode automatically
no matter the FUNCTION/POWER Switch (# 19) is in RADIO, TAPE or CD mode.
Remember to disconnect the connection cable from the CD player after use in order to
be able to listen to the RADIO, TAPE or CD player again.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
1. Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
2. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
3. Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
4. If drop-outs or interruptions occur in the music during CD play,
or if the CD fails to play at all, its bottom surface may require cleaning.
Before playing, wipe the disc fromthe center outwards with a good soft cleaning cloth.
COMPLIANCE WITH FCC REGULATIONS
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-
Consult the dealer or an experienced radio technician for help.
WARNING:
Changes or modifications to this unit not expressively approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If you experience difficulties in the use of this music system please check the following or call 1 800 777 5331 for Customer
Service.
Symptom
Possible Cause
Solution
Station not tuned properly for AM or FM.
FM: Telescopic antenna is not extended.
AM: The bar antenna is not positioned
correctly
Retune the AM or FM broadcast station.
FM: Extend FM Telescopic antenna.
AM: Reposition the unit until the best
reception is obtained.
Noise or sound distorted on AM or
FM broadcast
Slide Function/Power Switch to RADIO
position
Increase Volume
Unit not in RADIO function mode.
Volume set at minimum
AM or FM no sound
Unit not in CD function mode.
CD is installed incorrectly.
It the CD is self-compiled, the media used may not
be compatible with the player.
Batteries become exhausted
Select CD function mode.
Insert CD with label side up.
Use better quality blank media and retest.
Replace all batteries with new ones.
CD player will not play
Wipe CD with clean cloth or use
another disc.
CD skips while playing
Disc is dirty or scratched.
Dirty or defective disc
Dirty pick up lens
Player is subject to excessive shock or
vibration
Intermittent sound from CD Player
Clean or replace the defective disc
Use a CD-lens cleaning disc to clean the lens
Relocate the player away from shock or
vibration
Unit not in TAPE function mode
Volume at minimum
Slide Function/Power Switch to TAPE
Increase volume
Cassette Player no sound
Dirty tape head
Clean the head
Sound distorted
Speed varies
Clean the headReplace the tape
Clean roller and capstan
Tape old or worn
Dirty roller and capstan
Prevention tab removed
Cover hole with tape
Cassette Recorder will not record
Distorted sound on playback
Defective tape or dirty tape head
Replace tape or clean tape head
SERVICE
Please refer to the instructions on the enclosed warranty card for returning your unit for service. When returning the unit, please
remove any batteries to prevent damage to the unit in transit and/or from possible battery leakage. We are not responsible for
batteries returned with the product or for the cost of replacement.
Distributed by:
Spectra Merchandising International, Inc.
Chicago Industry Tech Park
4230 North Normandy Avenue
Chicago, Illinois 60634, U.S.A.
Please have model number ready, for Customer Service, call 1-800-777-5331
Printed in China
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|