SUMMER RAIN™
2 WALL & 3 WALL
WALK-IN SHOWER SYSTEMS
INSTALLATION AND OPERATING INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
2 WALL
Specifications _________________________________________________________________________ 2
Rough-in Reference ____________________________________________________________________ 3
Component Identification ________________________________________________________________ 4
Base Installation _______________________________________________________________________ 5-7
Tower and Glass Panels Installation ________________________________________________________ 8-12
3 WALL
Specifications _________________________________________________________________________ 13
Rough-in Reference ____________________________________________________________________ 14
Component Identification ________________________________________________________________ 15
Base Installation _______________________________________________________________________ 16-18
Tower and Glass Panels Installation ________________________________________________________ 19-22
2 & 3 WALL
Operation ___________________________________________________________________________ 23
Maintenance __________________________________________________________________________ 24
Authorized Service _____________________________________________________________________ 24
Tower Fixture Repair Parts _______________________________________________________________ 25
Tower Plumbing Repair Parts _____________________________________________________________ 26
2 Wall Unit Repair Parts _________________________________________________________________ 27
3 Wall Unit Repair Parts _________________________________________________________________ 28
Warranty _____________________________________________________________________________ 29-30
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model ____________________________________________________________________
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each unit arrives ready for installation, equipped with base, glass and associated hardware.
Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made.
Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for
partsandhardware. Shouldinspectionrevealanydamageordefectinanycomponent, donotinstalltheunit. Damage
or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's
responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims
for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty
information packed with the product.
Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by
following this inspection.
L
BASE SPECIFICATIONS
45° ELBOW
2 PROVIDED
(LOOSE)
1-1/2" TILE FLANGE
DIMENSIONS
60"
42-5/16" ( 1075 mm) W
4" ( 102 mm) H
(1219 mm) L
1/2" RIGID
COPPER PIPE
UNDER BASE
PRODUCT WEIGHT (Base + Enclosure )
196 lb
(89 kg)
W
TOTAL WEIGHT/
FLOOR LOADING
396 lb
(180 kg)/
23 lb/sq. ft.
(112 kg/sq. m)
TOP VIEW
NOTE: MINIMUM WATER PRESSURE
FOR THE SYSTEM IS 40 PSI.
1-1/2" TILE FLANGE
H
FRONT VIEW
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL ROUGH-IN REFERENCE
84"
FRONT VIEW
60"
33-3/4"
1-1/2" TILE FLANGE
23"
21-1/2"
1/2" RIGID
COPPER PIPE
UNDER BASE
27-15/16"
42-5/16"
COLD SUPPLY
HOT SUPPLY
MINIMUM WATER PRESSURE
FOR THE SYSTEM IS 40PSI
TOP VIEW
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL COMPONENT IDENTIFICATION
TOWER WITH PLUMBING,
FIXTURES, MAGNETIC
GASKET, BOTTOM PLATE
AND TOP COVER
HEX WRENCH (1)
(PROVIDED)
CURVED
GLASS
STRAIGHT
GLASS
(PREASSEMBLED)
MOUNTING
POST
CAP (2)
WALL
WALL
MOUNTING
POST
MOUNTING
POST
WALL
TOWER
SUPPORT
RAIL
MOUNT
BRACKET (2)
GLASS
PANEL
SUPPORT
RAIL
FRONT
RAIL
BRACKET
COVER (2)
GLAZING
GASKET
TAPE
(6 PIECES)
3 SCREWS AND
3 WALL ANCHORS
PER MOUNTING
POST
GLAZING GASKET (3)
CURVED
STRAIGHT
GLASS
GLASS
PANEL
GLAZING GASKET
TOWER
COVER
BOTTOM
TOWER MOUNTING
BOLT & WASHER
BRACKET
CORNER
POST
SELF
DRILLING
SCREW
BASE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL BASE INSTALLATION
INSTALLATION INSTRUCTIONS
PRELIMINARY ROUGH-IN
Thefloorstructurebeneaththeunitmustbeableto
support a total weight of the unit and bather. Refer
to the table under total weight.
STEP 2
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
ofcaulking(silicone)tothedrainholeandinsertthedrain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
Apply a lubricant (common household liquid soap
works well) to the inside of the rubber seal of the drain
assembly.
STEP 1
Provide an opening in the subfloor no less than 5" x 5"
square. This opening should be located on the center
lines of the shower base drain hole (See Product Chart).
The opening is to accommodate a 2" waste pipe. The
waste pipe should be 1/4" to 1/2" above the surface of
the subfloor.
STRAINER
APPLY LUBRICANT
SILICONE
SEALANT
DRAIN
ASSEMBLY
90°
SHOWER BASE
90°
90°
RUBBER WASHER
5"x5" OPENING
(MIN. AS POSSIBLE)
2" WASTE PIPE
NUT
FIBER WASHER
As shown in top view, 1/2" copper pipes are provided
toconnecttothewatersupply. Alsoprovidedare2loose
45° elbows as shown for installation in Detail 1.
STEP 3
If the subfloor is level, no other preparation is neces-
sary. You can proceed to install the shower base. If the
subfloor is not level, level shower base by spreading
floor leveling compound, mortar, plaster or minimal
expansion structural foam with a minimum density of 5
lbs./cubic feet EVENLY over ENTIRE area where base
will be installed. The compound used MUST make
contact with the entire bottom surface of the base. Both
sides of a joint or splice of subfloor should be level to
each other. Level and support waste pipe cutout area
greater than 5" x 5". The base is NOT to be supported
by the tile flange.
CAUTION: A nonflammable protective barrier must
be placed between soldering work and base unit to
prevent damage to the base.
When connecting the supply lines, the toe plate can be
notched to accommodate the pipes.
Thepipeunderthebasecanbecuttolength. Todoso,
removethepipeclampsunderthebase, cutthepipeand
reinstall pipes.
STUD
WALL
NOT PROVIDED
45° ELBOW
PROVIDED (2)
DEATAIL 1
SPREAD MORTAR OR LEVELING COMPOUND ETC.
EVENLY OVER ENTIRE AREA
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL BASE INSTALLATION
STEP 4
STEP 5
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place. You must
check the level of the base in two directions. Do not lift
a corner to level the base. This will cause a loss of
contact with the mortar. Attach the shower base flange
to the stud wall and blocking with self-drilling screws
(included). Use a minimum of 3 screws per flange
section.
With a large screwdriver and the tool included with the
drain, tighten the inside compression nut to seal the
drain pipe connection. After drain is fully installed, test
for proper drainage. If the shower base does not drain
properly, rectify this condition before proceeding with
theinstallation. JacuzziWhirlpoolBathisnotrespon-
sible for removal and/ or reinstallation costs.
NOTE: Watertight installation of the drain is the
installer’s responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath warranty.
Replace the strainer and tape over the drain hole to
prevent finishing material from entering drain.
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
POSITION BASE OVER CENTER OF
DRAIN PIPE AND SET INTO PLACE
NOTE: If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange.
TILE
FLANGE
SHIM
TILE
FLANGE
GAP
USE
SCREWS
(PROVIDED)
USE
SCREWS
(PROVIDED)
STUD
STUD
INCORRECT
CORRECT
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL BASE INSTALLATION
STEP 6
STEP 8
Place cement board or equivalent on top of shower
base flange and secure to studwall.
Filling the area marked DO NOT FILL will prevent
moisture from draining back into the base through the
weep holes. This moisture is due to leakage through the
tile grout. Sealing the tile grout will prevent this leakage.
CEMENT BOARD
TILE
CEMENT
BOARD
GROUT
STUD
STUD
SILICONE
SEALANT
SHIM IF NECESSARY
DO NOT FILL
STEP 7
Applytile(orotherfinishingmaterial)leavinga1/8"gap
between the finishing material and the shower base
flange lip. Seal this gap with silicone sealant. Leave a
minimum 1/4" gap at the back and front corners of the
shower base to allow drainage from leakage through
unsealed tiled grout.
1-1/8" MAXIMUM
NO MINIMUM
CLEAN-UP AFTER INSTALLATION
To avoid dulling and scratching the acrylic surface of
the base, never use abrasive cleaners. A mild liquid
detergent and warm water clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge.
Metal tools scratch the surface. Spots left by plaster or
grout can be removed if lightly rubbed with detergent on
a damp cloth or sponge.
TILE
CEMENT
BOARD
1/4" MINIMUM
GAP
Paint, tar, or other difficult stains can be removed with
paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
TILE
ADHESIVE
Minor scratches which do not penetrate the color
finish can be removed by lightly sanding with 600-grit
wet/dry sandpaper. You can restore the glossy finish to
the acrylic surface of the base with a special compound,
Meguiar’s #10 Mirror Glaze. If not available, use auto-
motive rubbing compound followed by an application of
automotive paste wax.
STUD
SILICONE
SEALANT
1/8" GAP
Major scratches and gouges which penetrate the
acrylic surface require refinishing. Ask your Jacuzzi
Whirlpool Bath dealer for special instructions.
SILICONE
SEALANT
1/4" MINIMUM GAP
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION
STEP 3A
STEP 1
Slidestraightglasspanelallthewayintowallpost. Mark
position of glass post. Remove panel.
Positionthewallpostssotheedgeofthepostissetback
3/4" (19 mm) in from the edge of the base
3/4"
(19 mm)
FINISH WALL
EDGE OF BASE
STEP 2
Level both wall posts in their proper position and mark
where screw holes are to be drilled. Drill 3/16" holes and
securewithwallanchorsandscrewsprovided. Cuta12"
strip of tape (provided) and apply firmly over screw
heads.
MARK POSITION
STEP 3B
Apply a bead of silicone sealant on underside of bottom
bracket corner post and place bracket where marked.
Drill pilot holes (#8 screw) and secure bracket to base.
Reinsertpanelintowallpostandpositionglasspostover
bracket.
TAPE
6 PLACES)
APPLY BEAD OF
SILICONE SEALANT
ON UNDERSIDE OF
BOTTOM BRACKET
CORNER POST
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION
STEP 4
STEP 6
Slide the glass panel into the wall post. Make sure that
the corner notch is positioned toward the base of the
tower.
Insert tower support rail into glass panel rail but do not
tighten at this time.
GLASS PANEL
SUPPORT RAIL
TOWER SUPPORT RAIL
STEP 7
Insertsupportrailsintobracketsintopmouldingoftower
but do not tighten at this time. Front and tower support
rails may have to be cut if they are too long.
TOWER SUPPORT RAIL
FRONT RAIL
NOTCH
GLASS PANEL
SUPPORT RAIL
STEP 5
Place the tower onto base. Ensure the curved glass
locates into the glazing channel. Install bolt but do not
tighten.
BOLT (5/16")
WASHER
STEP 8
Slide mounting bracket covers and mounting brackets
onto front rail and tower support rail.
GLAZING
CHANNEL
MOUNTING
BRACKET
COVER
RAIL
RAIL WALL
MOUNTING BRACKET
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION
STEP 9
STEP 11
Place the front rail and tower support rail against the
walls. Check level and mark the position for the rail
mounting bracket. The screw position will be above the
rail. Drill the wall with a 3/16" bit and secure bracket with
screws and wall anchors provided.
Secure the rails.
ATTACH RAIL
BRACKET TO WALL
SECURE RAIL TO
BRACKET (TURN CW
TO TIGHTEN)
STEP 12
MOVE COVER CAP
OVER BRACKET
Tighten the tower base bolt. Two shut-off valves are
provided. To hook up supply lines, unscrew valves from
braided line. Using thread sealant, screw valve to stub
outs at bottom of tower. Then reconnect braided line
using provided gasket. Do not twist or kink supply lines
when connecting.
STEP 10
Adjust the rails until tower is vertical in 2 planes.
SHUT OFF
VALVES
(PROVIDED)
COLD
HOT
BOLT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION
STEP 14
STEP 13A
Install cover cap on fixed glass wall post.
Insert fixed glass support rail into panel post and tighten
set screw.
COVER CAP
STEP 13B
Drill a 1/8" pilot hole into tower support rail using the hole
in the glass panel support rail. Screw M3.5X9.5 mm
screw into hole.
STEP 15
Install glazing gasket on curved glass wall post on the
outside. Note orientation of gasket. Soapy water may
help to insert the glazing gasket. On the inside of
enclosure, apply sealant the entire length of glass and
wall post as well as the entire length of glass and tower.
DRILL 1/8" PILOT HOLE AND
SCREW M3.5X9.5 mm SCREW
INTO HOLE
GLASS PANEL
SUPPORT RAIL
GLASS
INSIDE OF
ENCLOSURE
WALL POST
APPLY SEALANT
GLAZING GASKET
GLAZING
GASKET
TOWER TOP PLATE
APPLY
SEALANT
INSIDE OF
ENCLOSURE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION
STEP 16
STEP 18
Turn on water supply and check for leaks. Correct any
leaks before installing tower cover.
Seal all around the base of tower with silicone sealant.
Alsosealtheinsideofbothwallposts, glasspostandthe
bottom of both glass panels on the inside only.
STEP 17
Install tower cover as shown. Insert cover at top first.
APPLY SEALANT
ALONG BASE
AND SIDE OF
WALL POST
TOWER TOP PLATE
APPLY SEALANT
ALONG BASE
APPLY SEALANT
OF GLASS
ALONG BASE
OF GLASS
TOWER COVER
INSERT THIS SIDE FIRST
TOWER COVER
APPLY SEALANT
APPLY SEALANT
ALL AROUND
TOWER BASE
APPLY SEALANT
ALONG BASE
AND SIDE OF
WALL POST
AROUND
GLASS POST
(RAILS NOT SHOWN)
TOP VIEW
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each unit arrives ready for installation, equipped with base, glass and associated hardware.
Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made.
Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for
partsandhardware. Shouldinspectionrevealanydamageordefectinanycomponent, donotinstalltheunit. Damage
or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's
responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims
for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty
information packed with the product.
Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by
following this inspection.
L
BASE SPECIFICATIONS
45° ELBOW
2 PROVIDED
(LOOSE)
1-1/2" TILE FLANGE
DIMENSIONS
60"
(1219 mm) L
42-5/16" ( 1075 mm) W
4"
( 102 mm) H
1/2" RIGID
COPPER PIPE
UNDER BASE
PRODUCT WEIGHT (Base + Enclosure )
140 lb
(64 kg)
W
TOTAL WEIGHT/
FLOOR LOADING
340 lb
(155 kg)/
23 lb/sq. ft.
(97 kg/sq. m)
TOP VIEW
NOTE: MINIMUM WATER PRESSURE
FOR THE SYSTEM IS 40 PSI.
1-1/2" TILE FLANGE
H
FRONT VIEW
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL ROUGH-IN REFERENCE
84"
FRONT VIEW
60"
33-3/4"
1-1/2" TILE FLANGE
23"
21-1/2"
1/2" RIGID
COPPER PIPE
UNDER BASE
27-15/16"
42-5/16"
COLD SUPPLY
HOT SUPPLY
MINIMUM WATER PRESSURE
FOR THE SYSTEM IS 40PSI
TOP VIEW
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL COMPONENT IDENTIFICATION
TOWER WITH PLUMBING,
FIXTURES, MAGNETIC
CURVED
GLASS
GASKET, BOTTOM PLATE
AND TOP COVER
HEX WRENCH (1)
(PROVIDED)
WALL
(PREASSEMBLED)
MOUNTING
POST
CAP
MOUNTING
POST
WALL
TOWER
MOUNT
SUPPORT
RAIL
BRACKET (2)
FRONT
RAIL
BRACKET
COVER (2)
TAPE
(3 PLACES)
3 SCREWS AND
3 WALL ANCHORS
GLAZING
GASKET
CURVED
GLASS
GLAZING GASKET (2)
TOWER COVER
TOWER MOUNTING
BOLT & WASHER
SELF
DRILLING
SCREW
BASE
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL BASE INSTALLATION
PRELIMINARY ROUGH-IN
INSTALLATION INSTRUCTIONS
Thefloorstructurebeneaththeunitmustbeableto
support a total weight of the unit and bather. Refer
to the table under total weight.
STEP 2
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
ofcaulking(silicone)tothedrainholeandinsertthedrain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
Apply a lubricant (common household liquid soap
works well) to the inside of the rubber seal of the drain
assembly.
STEP 1
Provide an opening in the subfloor no less than 5" x 5"
square. This opening should be located on the center
lines of the shower base drain hole (See Product Chart).
The opening is to accommodate a 2" waste pipe. The
waste pipe should be 1/4" to 1/2" above the surface of
the subfloor.
STRAINER
APPLY LUBRICANT
SILICONE
SEALANT
DRAIN
ASSEMBLY
SHOWER BASE
90°
90°
RUBBER WASHER
2" WASTE PIPE
5"x5" OPENING (MIN. AS POSSIBLE)
NUT
FIBER WASHER
As shown in top view, 1/2" copper pipes are provided
toconnecttothewatersupply. Alsoprovidedare2loose
45° elbows as shown for installation in Detail 1.
STEP 3
If the subfloor is level, no other preparation is neces-
sary. You can proceed to install the shower base. If the
subfloor is not level, level shower base by spreading
floor leveling compound, mortar, plaster or minimal
expansion structural foam with a minimum density of 5
lbs./cubic feet EVENLY over ENTIRE area where base
will be installed. The compound used MUST make
contact with the entire bottom surface of the base. Both
sides of a joint or splice of subfloor should be level to
each other. Level and support waste pipe cutout area
greater than 5" x 5". The base is NOT to be supported
by the tile flange.
CAUTION: A nonflammable protective barrier must
be placed between soldering work and base unit to
prevent damage to the base.
When connecting the supply lines, the toe plate can be
notched to accommodate the pipes.
Thepipeunderthebasecanbecuttolength. Todoso,
removethepipeclampsunderthebase, cutthepipeand
reinstall pipes.
STUD
WALL
NOT PROVIDED
45° ELBOW
PROVIDED (2)
DEATAIL 1
SPREAD MORTAR OR LEVELING COMPOUND ETC.
EVENLY OVER ENTIRE AREA
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL BASE INSTALLATION
STEP 4
STEP 5
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place. You must
check the level of the base in two directions. Do not lift
a corner to level the base. This will cause a loss of
contact with the mortar. Attach the shower base flange
to the stud wall and blocking with self-drilling screws
(included). Use a minimum of 3 screws per flange
section.
With a large screwdriver and the tool included with the
drain, tighten the inside compression nut to seal the
drain pipe connection. After drain is fully installed, test
for proper drainage. If the shower base does not drain
properly, rectify this condition before proceeding with
theinstallation. JacuzziWhirlpoolBathisnotrespon-
sible for removal and/ or reinstallation costs.
NOTE: Watertight installation of the drain is the
installer’s responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath warranty.
Replace the strainer and tape over the drain hole to
prevent finishing material from entering drain.
WHEN SCREWING FLANGE TO STUD
WALL START WITH THIS SIDE
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
POSITION BASE OVER CENTER OF
DRAIN PIPE AND SET INTO PLACE
NOTE: If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange.
TILE
FLANGE
SHIM
TILE
FLANGE
GAP
USE
SCREWS
(PROVIDED)
USE
SCREWS
(PROVIDED)
STUD
STUD
INCORRECT
CORRECT
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL BASE INSTALLATION
STEP 6
STEP 7
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place. You must
check the level of the base in two directions. Do not lift
a corner to level the base. This will cause a loss of
contact with the mortar. Attach the shower base flange
to the stud wall and blocking with self-drilling screws
(included). Use a minimum of 3 screws per flange
section.
With a large screwdriver and the tool included with the
drain, tighten the inside compression nut to seal the
drain pipe connection. After drain is fully installed, test
for proper drainage. If the shower base does not drain
properly, rectify this condition before proceeding with
theinstallation. JacuzziWhirlpoolBathisnotrespon-
sible for removal and/ or reinstallation costs.
NOTE: Watertight installation of the drain is the
installer’s responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath warranty.
Replace the strainer and tape over the drain hole to
prevent finishing material from entering drain.
CEMENT BOARD
TILE
CEMENT
BOARD
GROUT
STUD
STUD
SILICONE
SEALANT
SHIM IF NECESSARY
DO NOT FILL
NOTE: If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange.
1-1/8" MAXIMUM
NO MINIMUM
CLEAN-UP AFTER INSTALLATION
SILICONE
SEALANT
To avoid dulling and scratching the acrylic surface of
the base, never use abrasive cleaners. A mild liquid
detergent and warm water clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge.
Metal tools scratch the surface. Spots left by plaster or
grout can be removed if lightly rubbed with detergent on
a damp cloth or sponge.
1/4" MINIMUM GAP
Paint, tar, or other difficult stains can be removed with
paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
Minor scratches which do not penetrate the color
finish can be removed by lightly sanding with 600-grit
wet/dry sandpaper. You can restore the glossy finish to
the acrylic surface of the base with a special compound,
Meguiar’s #10 Mirror Glaze. If not available, use auto-
motive rubbing compound followed by an application of
automotive paste wax.
TILE
CEMENT
BOARD
1/4" MINIMUM
GAP
Major scratches and gouges which penetrate the
acrylic surface require refinishing. Ask your Jacuzzi
Whirlpool Bath dealer for special instructions.
TILE
ADHESIVE
STUD
SILICONE
SEALANT
1/8" GAP
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL: TOWER AND CURVED GLASS INSTALLATION
STEP 3
STEP 1
Slide the glass panel into the wall post. Make sure that
the corner notch is positioned toward the base of the
tower.
Position the wall post so the edge of the post is set back
3/4" (19 mm) in from the finish wall.
FINISH WALL
3/4"
(19 mm)
STEP 2
Level the post in its proper position and mark where
screwholesaretobedrilled. Drill3/16"holesandsecure
with wall anchors and screws provided. Cut a 12" strip
of tape (provided) and apply firmly over screw heads.
NOTCH
STEP 4
Place the tower onto base. Ensure the curved glass
locates into the glazing channel. Install bolt but do not
tighten.
TAPE
3 PLACES)
BOLT (5/16")
WASHER
GLAZING
CHANNEL
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL: TOWER AND CURVED GLASS INSTALLATION
STEP 7
STEP 5
Place the front rail and tower support rail against the
walls. Check level and mark the position for the rail
mounting bracket. The screw position will be above the
rail. Drill the wall with a 3/16" bit and secure bracket with
screws and wall anchors provided.
Insertsupportrailsintobracketsintopmouldingoftower
but do not tighten at this time.
TOWER SUPPORT RAIL
FRONT RAIL
ATTACH RAIL
BRACKET TO WALL
SECURE RAIL TO
BRACKET (TURN CW
TO TIGHTEN)
STEP 6
Slide mounting bracket covers and mounting brackets
onto front rail and tower support rail.
MOVE COVER CAP
OVER BRACKET
MOUNTING
BRACKET
COVER
RAIL
STEP 8
Adjust the rails until tower is vertical in 2 planes.
RAIL WALL
MOUNTING BRACKET
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL: TOWER AND CURVED GLASS INSTALLATION
STEP 9
STEP 11
Secure the rails.
Install cover cap on wall post.
COVER CAP
STEP 10
STEP 12
Tighten the tower base bolt. Two shut-off valves are
provided. To hook up supply lines, unscrew valves from
braided line. Using thread sealant, screw valve to stub
outs at bottom of tower. Then reconnect braided line
using provided gasket. Do not twist or kink supply lines
when connecting.
Install glazing gasket on curved glass wall post on the
outside. Note orientation of gasket. Soapy water may
help to insert the glazing gasket. On the inside of
enclosure, apply sealant the entire length of glass and
wall post as well as the entire length of glass and tower.
SHUT OFF
VALVES
(PROVIDED)
GLASS
COLD
INSIDE OF
ENCLOSURE
WALL POST
HOT
BOLT
APPLY SEALANT
GLAZING GASKET
GLAZING
GASKET
TOWER TOP PLATE
APPLY
SEALANT
INSIDE OF
ENCLOSURE
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL: TOWER AND CURVED GLASS INSTALLATION
STEP 13
STEP 15
Turn on water supply and check for leaks. Correct any
leaks before installing tower cover.
Seal all around the base of tower with silicone sealant.
Also seal the inside of both wall posts, bottom of both
glass panels on the inside only.
STEP 14
Install tower cover as shown. Insert cover at top first.
APPLY SEALANT
ALONG BASE
OF GLASS
TOWER TOP PLATE
TOWER COVER
APPLY SEALANT
ALL AROUND
TOWER BASE
APPLY SEALANT
ALONG BASE
AND SIDE OF
WALL POST
INSERT THIS SIDE FIRST
TOWER COVER
(RAILS NOT SHOWN)
TOP VIEW
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2 & 3 WALL OPERATION
Shower Head
There are four selectable positions: Jet, normal pulsating and
aerated flow.
Body Sprays (2 Upper & 2 Lower)
To adjust the flow and intensity, turn as shown. The spray can also
be turned to change the direction of the spray.
LESS FLOW AND INTENSITY
MORE FLOW AND INTENSITY
Diverter Control
To turn On water, turn the inner knob clockwise and adjust for more
or less flow.
The outer knob will divert the water to body sprays, shower head
(shown in this position) and foot temperature tester. If the knob is
pointing anywhere between main functions, the amount of water
will be proportional to where the knob is pointing. If the knob is
pointing to the white line between positions, the water will be
diverted equally to both functions on either side of the white line.
STOP RELEASE
SHOWER
HEAD
BODY
SPRAY
FOOT
TEMPERATURE
TESTER
INNER
KNOB
OUTER
KNOB
Temperature Valve
The temperature of the mixed water is adjusted by means of the
graduated handle. This handle has a safety stop set at 100°F
(38°C). To increase the temperature, press the red button to release
the stop and keep turning the handle.
Foot Temperature Testor
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2 & 3 WALL MAINTENANCE
To remove any lime scale from the shower head and body sprays , rub with your finger the outer ring of nozzles on
the shower head and all nozzles on the body spray.
To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools
(such as scissors or screwdrivers, etc.) to clean the body sprays, shower head or foot temperature tester.
To cleanthe base, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to
a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic
finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable.
The glass can be cleaned with any glass-cleaning product available on the market.
Do not use abrasives, alcohol, acetone, ammonia or other solvents on any tower component.
The thermostatic valve has 2 screen filters that should be cleaned periodically. To remove the filters turn off hot and
cold supplies. Remove tower cover. Disconnect the supply hoses from the valve and remove filter from the hose.
Clean any debris. Reinstallation is the reverse of removal. Turn on hot and cold supply and check for leaks.
Authorized Service
If you need a referral for a service company near you, or need assistance with operation or maintenance related
questions, please call our Service Support Department at 1-800-288-4002. For service agent listing, visit our web site
at http://www.jacuzzi.com/. To find the service agent listings, click on “For The Trade”. Then click on Electrical/
Mechanical Service Agents. Depending on the problem, click on “Electrical/Mechanical Repairs” or “Finish, Surface
or Shell-Related Problems”.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
P.O. Box 702168, Dallas, TX 75370-2168
Service Support: Call (800) 288-4002
© 2002 Jacuzzi Whirlpool Bath U223000 8/13/04
Printed on Recycled Paper
Printed in U.S.A.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWER FIXTURES REPAIR PARTS
1 (5X)
2 (5X)
3 (5X)
TOWER ASSEMBLY
4
9 (5X)
6
10
5
11 (4X)
7 (Part of U547000)
8
12
13
14
15
16
17
18
PART OF D709827
WASHER (PART OF D709827)
19
1. C546000 Lock Nut, 1/2" NPT WP (5X)
2. G559000 Ring Compression SS (5X)
3. G560000 Washer Rubber (5X)
4. U546000 (Part of U547000) Nut Transfer Valve, Chrome
5. U566000 Gasket, 1.41 ID X .063 Thick
6. U547000 Valve, Mixer/Transfer Assembly
7. U550827 (Part of U547000) 567000Nut, Mixer Valve, Chrome
8. U567000 Gasket, 1.9 ID X .063 Thick
9. G432000 Nipple,1/2" Close
10. U217827 Shower Head, Chrome
11. U215827 Jet, Wall Body, Chrome
12. U219827 Face Plate, Transfer Valve, Chrome
13. U546827 Nut Transfer Valve, Chrome
14. U545827 Collar, Transfer Valve, Chrome
15. U544000 O-Ring, Transfer Valve
16. U543827 Knob, Flow Control, Chrome
17. U549827 Collar, Mixer Valve, Chrome
18. U548827 Knob, Mixer Valve Chrome
19. D709827 Fill Spout Assembly, Stubby, Chrome
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWER PLUMBING REPAIR PARTS
1. A944000 (9X) Spring Clamp, .625 OD Hose
2. U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb
3. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb
4. A945000 (7X) Spring Clip, .75 OD Hose
5. U400000 FTG, Straight, 1/2" FTS X 10mm Barb
6. U403000 (2X) Cap, 1/2" FST
1 (9X)
See Note 1
2
7. U711000 (2X) Strainer Washer, 1/2" Dia.
8. U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb
9. U540000 (2X) 1/2" Flexhose 38", Female Swivel Heads
10. GASKET (2X) Gaskets Supplied with Hose
11. U827000 (2X) Ball Valve, .5 FTP X .5 MPT L
12. U421000 (11X) Washer, FTG .7 OD
12 (11X)
13 (7X)
13. U401000 (7X) FTG, Ell, 1/2" FST X 10mm Barb
14. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb
15. U404000 (2X) FTG, Y, 10mm X 10mm X 10mm Barb
16. U405000 L=2.5" Tubing, PVC Reinforced, 10mm Barb
17. U402000 FTG, Tee, 1/2" FST X 10mm Barb
18. U405000 L=10.0" Tubing, PVC Reinforced, 10mm Barb
19. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb
20. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb
3
14
4 (7X)
See Note 2
15 (2X)
16
17
5
Note 1: For Clamping U405000 to U401000 or U402000.
Note 2: For Clmping U405000 to U400000 or U404000.
18
6
7
8
19
9 (2X)
20
10 (2X)
11
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2 WALL UNIT REPAIR PARTS
5 (2X) 6 (2X)
7 (6X)
4
1
3
2
8
11
12
9
10
14 (6X)
13 (6X)
17
19 (Used with Tower with Timber Finish Only)
18
21
15
1. U134827 Rail Back Walk-in
2. U133827 Rail 2 Wall Walk-in
3. U245827 Rail Assembly Walk-in
4. U149000 Bracket, Mounting Rail
5. U119827 Wall Post, Panel
16
6. U138827 Cap, Wall Post
7. J686000 Tape High Bond, 2 Sided
8. U159000 Gasket,Vinyl, Glass Panel
9. U479XXX Glass Panel Assembly, Walk-in
10. U124XXX Tower Cover
22
20
11. U257XXX Final Shell, Tower Walk-in
U126XXX Tower Body Walk-in
U136XXX Cap, Top, Tower
U137XXX Cap, Bottom, Tower
U149000 Bracket, Mounting Rail
For colors for U174XXX Shower Base
substitute XXX for:
Standard
For finishes for U124XXX Tower
Cover and U257XXX Tower Final
Shell substitute XXX for:
801 Satin
U354000 Screw, Self Tap, #8-1.25" L
U355000 Screw, Self Tap, #8-2.0" L
12. U113000 Glass Panel, Front, Wlak-in
13. U354000 Screw Self Tap #8 X 1.25" L
14. U703000 Anchor, #6-8-10
15. 5374832 Screw, Sheet Metal PHP, #6 X .88" L
16. U196000 Bracket Corner Post, Bottom
17. 3952832 Bolt Hex FL Thrd 5/16
18. 3983832 Washer 5/16 Flat Type A Plnwdser
19. U247000 Gasket,Vinyl, Glass Panel
20. U174XXX Shower base Walk-in 2 Wall
21. U220000 Screw Self Drilling, #8 X 1.63" L
22 9959000 Drain, Non-Caulk
959 White
958 Almond
827 Chrome
969 Oyster
938 Timber
959 White
945 Silver
High Fashion
917 Black
949 Rose
951 Shell
978 Forest Green
984 Shy Blue
999 Sand
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3 WALL UNIT REPAIR PARTS
5
1
3 (2X)
4
2
10
11
7
8 (2X)
9
1. U134827 Rail Back Walk-in 3 Wall
6
2. U245827 Rail Assembly Walk-in 3 Wall
3. U149000 Bracket, Mounting Rail
4. U119827 Wall Post, Panel
5. U138827 Cap, Wall Post
6. U124XXX Tower Cover
13
7. U257XXX Final Shell, Tower, Walk-in 3-Wall
U126XXX Tower Body Walk-in
12
U136XXX Cap, Top Tower
U137XXX Cap, Bottom, Tower
U149000 Bracket, Mounting Rail
U354000 Screw, Self Tap,#8-1.25" L
U355000 Screw, Self Tap,#8-2.0" L
8. U247000 Gasket,Vinyl, Glass Panel
9. U113000 Glass, Panel, Front, Walk-in
10. U159000 Gasket,Vinyl, Glass Panel
11. J686000 Tape, High Bond, 2-Sided
12. U354000 Screw Self Tap, #8-1.25" L
13. U703000 Anchor, #6-8-10
14. 3952832 Bolt Full Thread, 5/16
15. 3983832 Washer, 5/16, Flat, Type 2 Plnwser
16. U171XXX Shower base, Walk-in, 3-Wall
17. U220000 Screw Self Drilling, #8 X 1.63" L
18. 9959000 Drain, Non-Caulk
For finishes for U124XXX Tower
Cover and U257XXX Tower Final
Shell substitute XXX for:
801 Satin
17 (10X)
827 Chrome
938 Timber
959 White
14
15
For colors for U171XXX Shower Base
substitute XXX for:
Standard
959 White
958 Almond
969 Oyster
945 Silver
18
High Fashion
917 Black
16
949 Rose
951 Shell
978 Forest Green
984 Shy Blue
999 Sand
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Jacuzzi Whirlpool Bath Limited Warranty
Designer Collection Shower Product
WARRANTY COVERAGE
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer
Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the
unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed components against
defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options and
accessoriesmanufacturedbytheCompanyagainstdefectsofmaterialorworkmanship.Warrantycoveragebeginsonthedatetheoptionoraccessorywasoriginally
purchased by the user.
WARRANTY LIMITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without
limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including modification
to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with the unit); connections
supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack of proper routine
maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper cleaners; or
acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa
chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company; the unit's prior usage
as an operational display; or defects that should have been discovered before installation. This limited warranty does not include: labor, transportation, or other
costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs relating to obtaining access for repair;
orlossofusedamage,includinglossofsales,profitorbusinessadvantageofanykindunderanycircumstances.Bathunitsareexcludedfromanywarrantycoverage
if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America and Canada.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO
THE FULL EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable
to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for
any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished
by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool Bath
in order for this warranty to become effective.
Jacuzzi Whirlpool Bath
P.O. Box 702168
Dallas, TX 75370-2168
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSIBILITIES OF OTHERS
Inspectingtheunitpriortoinstallationistheresponsibilityoftheinstallerorbuildingcontractorwhoactsonbehalfoftheuser.Theyareresponsibleforensuring
the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of
a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper
inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered.
If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should
be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating to
obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are
warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the
time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes in
U.S.A. or municipal or provincial codes in Canada.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents
or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered
by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the
problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure
occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the
unit during regular business hours within a reasonable time after the problem was reported by the user.
Inordertoobtainwarrantyservice,consultyourlocaltelephonebookforthelocationofthenearestJacuzziWhirlpoolBathAuthorizedServiceAgent.Describe
the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
P.O. Box 702168
Dallas, TX 75370-2168
Call: (800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company,
call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at
your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the
Company's warranty obligation.
©2002 Jacuzzi Whirlpool Bath U223000 8/13/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|