Water Rainbow™ Fill Spout/Faucet Kit
Installation Instructions
IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.
TheWaterRainbowfillspout/faucetkitisdesigned
for installation on most Jacuzzi Whirlpool Bath
products or on any bath having sufficient rim space
WATER RAINBOW FILL SPOUT
AND FAUCET HANDLES
for mounting. The installation procedure requires
drilling holes in the bath shell, mounting fittings,
and making the proper water supply connections
to the faucet valves and fill spout. Hole drilling
templates and instructions are provided here for
this purpose.
Contents of Kit: Water Rainbow fill spout as-
sembly, faucet handles with inserts--hot (red dot)
and cold (blue dot), faucet valve assembly (2),
1/4-20 x 1-1/2" hex bolt with/washer and locknut
(2), 1-1/2" diameter. push-on speednut (2), faucet
handle gasket (2), #10-24 x 3/8" PHPM screw (2),
1/4" MIN.
cartridge valve wrench with instructions.
RIM
Preparation
Locate the area on the bath or spa rim where
the Water Rainbow and faucet valves are to be
installed. For separated valve installations, refer to
illustrations B and G; for paired valve installations,
refer to illustrations C and H.
INSIDE OF
BATH
LOCATE FILL SPOUT
ON TOP OF BATH
RIM TO ALLOW
Forinstallationonallbaths,locatetheWaterRain-
bow fill spout and valves on a level surface which
will allow water to clear the rim and flow directly into
the bath (see illustration A). Also be certain the fill
spout has easy access and that there is adequate
space for plumbing connections to the fill spout,
both before and after installation. (Refer to plumb-
ing instructions regarding top access installation,
illustration M.)
DIRECT WATER
FLOW INTO BATH
A
HOLE FOR FILL SPOUT
HOT WATER
COLD WATER
FAUCET HOLE
B
1-1/2" DIA.
FAUCET HOLE
2-1/2"
2-1/2"
1-1/2" DIA.
1/2"
15/64" DIA.
9/32" DIA.
15/64" DIA.
9/32" DIA.
1/2"
11/16"
15/64" DIA.
15/64" DIA.
15/64" DIA.
1-3/8" DIA.
15/64" DIA.
15/64" DIA.
7"
7"
Dry fit the Water Rainbow fill spout and valves in
the desired area (before drilling holes) to be sure
the location is appropriate.
INTERIOR OF
BATH OR SPA
HOLE DRILLING SCHEME FOR WATER RAINBOW
SPOUT AND FAUCETS - SEPERATE VALVE CONFIGURATION
Drilling Holes
Detach the templates (on back page) and tape
them onto the acrylic surface of the bath rim, lo-
cating the center lines of the fill spout and valve
holes according to appropriate dimensions given
in Illustration B or C.
HOLE FOR
FAUCET
HOLES
C
FILL SPOUT
2-1/2"
HOT
COLD
1-1/2" DIA.
1-1/2" DIA.
1/2"
1/2"
15-64"
15/64" DIA.
11/16"
15/64"
3"
9/32" DIA.
1-3/8" DIA.
2-1/2"
9/32" DIA.
7"
Note: To insure template has been printed to
scale, measure the 2 1/2" spacing from center
Fill Spout mark and 9/32" hole mark for the 1/4
- 20 Hex Bolt anchors.
15/64" DIA.
INTERIOR OF
BATH OR SPA
HOLE DRILLING SCHEME FOR WATER RAINBOW
SPOUT AND FAUCETS - PAIRED VALVE CONFIGURATION
Jacuzzi Whirlpool Bath
6683000G
8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREW #10-24 X3/8" PHPM (2)
SUGGESTED WATER RAINBOW
PLUMBING SCHEME A - FOR
SEPARATED VALVE
INSERT
FAUCET HANDLE
(HOT)
WATER RAINBOW
FILL SPOUT
CONFIGURATIONS
(Pipe and fittings not provided.)
GASKET
FAUCET HANDLE (2)
INSERT
FAUCET HANDLE
(COLD)
LOCKNUT
1/4-20 (2)
VALVE (2)
WASHER
FAUCET HANDLE (2)
FAUCET WRENCH
1/4" FLAT (2)
5/8" X 1/2"
ELL
BOLT
1/4-20 X 1-1/2"
HEX HEAD
HOT WATER
SUPPLY
5/8" O.D.
COPPER PIPE
TEE 5/8" X 5/8" X 1/2"
SPEEDNUT
PUSH-ON 1-1/2" (2)
5/8" O.D.
COPPER PIPE
5/8" X 1/2"
ELL
COLD WATER
SUPPLY
G
WATER RAINBOW
FILL SPOUT
SUGGESTED WATER RAINBOW
PLUMBING SCHEME B - FOR
PAIRED VALVE CONFIGURATIONS
(Pipe and fittings not provided.)
INSERT
FAUCET HANDLE
(HOT)
LOCKNUT
1/4-20 (2)
WASHER
1/4" FLAT (2)
FAUCET
INSERT FAUCET HANDLE
(COLD)
HANDLE (2)
SCREW #10-24 X3/8" PHPM (2)
GASKET
5/8" O.D.
BOLT
FAUCET HANDLE (2)
COPPER PIPE
1/4-20 X 1-1/2"
HEX HEAD
FAUCET WRENCH
VALVE (2)
5/8" X 1/2"
ELL
5/8" O.D.
COPPER PIPE
TEE 5/8" X 5/8" X 1/2"
SPEEDNUT
PUSH-ON 1-1/2" (2)
HOT WATER
SUPPLY
5/8" X 1/2"
ELL
COLD WATER
SUPPLY
H
Jacuzzi Whirlpool Bath
6683000G
8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Faucet Handles
Install the rubber gasket into the faucet handle
aligning the flat of the gasket with the projection
fromthehandle,thenaligningtheflatsurfaceonthe
stem with the flat inside handle, place the handle
onto the stem of the faucet valve.
Insert the #10-24 x 3/8" L stainless steel PHPM
screw (provided) through the handle and gasket
into the valve stem and tighten.
INSERT
SCREW
FAUCET
HANDLE
Rotate handles clockwise to the end of travel.
Pushininsertswithdotsorientedtowardtheouter
edge of the bath rim, red dot indicating hot water
and blue dot indicating cold water. The notch in
the insert must align with the ribs on the inside of
the handles for flush engagement. (See illustra-
tion I.)
RUBBER
GASKET
VALVE STEM
FAUCET HANDLE ASSEMBLY
I
Plumbing Connections
Note: Turn off water at main shut-off valve before
making plumbing connections to supply lines.
Connect the water line from the hot and cold valve
to the threaded pipe extension of the fill spout per
illustration G or H. Use Teflon tape or thread seal-
ant designed for use on plastics. Do not use oil
base thread compounds.
OPTIONAL SHOWER HEAD
(NOT SUPPLIED)
TRANSFER VALVE
(NOT SUPPLIED)
For bath fill spout only applications, refer to the
suggested plumbing schemes G for separated
valves and H for paired valves. If a rim or wall
mounted shower is installed, a transfer or mixer
valve will be required. Three variations are shown
in illustration J (standard shower), K (rim mounted
or hand held), and L(shower with anti-siphon valve
if required by code.
If local plumbing codes require the installation of
an anti-siphon valve, locate the anti-siphon valve
6" above the rim of the bath in a vertical position
over a waterproof surface or fixture to allow for
any possible water leakage through the air vent.
The valve must be exposed and have access for
service.
COLD WATER
HOT WATER
SUPPLY
SUPPLY
J
HAND HELD SHOWER
(NOT SUPPLIED)
TRANSFER VALVE
(NOT SUPPLIED)
Operation
Checkforproperoperationofthefillspout. Always
fillthebathwithamixtureofhotandcoldwater. Wa-
ter temperatures in excess of 140° F may damage
the fill spout and/or discolor the bath's surface.
HOT WATER
SUPPLY
COLD WATER
SUPPLY
K
Jacuzzi Whirlpool Bath
6683000G
8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for Top Access
OPTIONAL SHOWER HEAD
(NOT SUPPLIED)
If service access to Water Rainbow plumbing
under the rim is not possible, it is possible to install
the spout so that it can be replaced at a later date
(if necessary) from the top of the rim. To do this,
allow at least 2" of flexibility in the piping so it can
be pulled up through the rim. Use a compression
fitting or union at the connection of the pipe exten-
sion to allow disconnection without rotating the fill
spout. If a compression fitting is not used, make
sure there is a space of at least 6" from the back
of the Water Rainbow to the wall, so the spout can
be rotated to unscrew it from the piping. (See il-
lustration M.)
ANTI-SIPHON VALVE SHOULD
BE A MINIMUM OF 6" ABOVE
RIM OF BATH
ANTI-SIPHON VALVE
& TRANSFER VALVE
(NOT SUPPLIED)
6"
To remove the fill spout from the top of the bath,
first pry off the cover. Do not use sharp tools!
Then remove the two larger screws and pull the
spout up.
COLD WATER
SUPPLY
L
HOT WATER
SUPPLY
ALLOW 6" TO ROTATE
Faucet Valve Replacement
FILL SPOUT FOR REMOVAL
Jacuzzi Whirlpool Bath has provided a special
wrench with which to change the cylinder valve
assembly under the water supply handles should
it require replacement. Keep this tool in a safe
place for use at a later date. To replace the cylinder
valve and the seat assembly, first turn off the water
supply, then pry the insert from the square handle.
Next,removethePhillipsscrewsecuringthehandle
and remove the handle. Place the wrench on the
bonnet and turn it counterclockwise. Next, remove
the bonnet, leaving it in the wrench.
ALLOW AT LEAST 2" OF
FLEXABILITY IN PLUMBING
TO LIFT FILL SPOUT
WALL
COMPRESSION
FITTING
BATH
RIM
Note the position of the valve cylinder stop before
removing the cylinder. Now use pliers to pull the
valve cylinder stem out of the body, then slip the
replacement cylinder unit into the body so that
stops of both faucets are positioned downward,
toward the bottom of the bath allowing rotation in
the same direction.
Secure the bonnet in place with the wrench. Re-
place the handle and the screw. Snap the insert
into place. (See illustration N.) The above faucet
replacement parts are available from your Jacuzzi
Whirlpool Bath dealer.
INSTALLING THE WATER RAINBOW
WITH TOP ACCESS
M
BODY
ALIGN NOTCH
WITH PROJECTIONS
BONNET
WRENCH
SPRING
SEAT
VALVE
CYLINDER
GASKET
HANDLE
SCREW
INSERT
N
FAUCET ASSEMBLY
Jacuzzi Whirlpool Bath
6683000G
8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Since plumbing fittings may contribute detectable amounts of lead to water, the following notice is required by California law
(Proposition 65). "This product contains a chemical known to the State of California to cause birth defects or reproductive harm."
In normal use, any lead exposure can be minimized by allowing the water to run free for several seconds before drinking.
Proper installation of the fill spout and compliance with local codes is the responsibility of the installer. Jacuzzi Whirlpool Bath does
not warrant connections of water supply fittings and piping, fill systems, or drain/overflow systems. Nor is it responsible for damage
to the bath (or spa) which occurs during any installation procedure.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the
product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
14801 Quorum Dr., Dallas TX 75254
Customer Service: Call (800) 288-4002
© Copyright 1991 Jacuzzi Whirlpool Bath 6683000G 8/06
Printed in the U.S.A.
Printed on Recycled Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
HOLE DRILLING TEMPLATE—WATER RAINBOW™
CHECK TEMPLATE SCALE USING
REFERENCE DIMENSIONS BEFORE DRILLING
If scale is off, do not continue, call customer support at 1-800-288-4002 to obtain a new template
BATH RIM
HOLE FOR THREADED
PIPE EXTENSION
9/32" DIA.
(FILL SPOUT)
1-3/8" DIA.
(2-1/2" REF)
(1/2" REF)
9/32" DIA.
C
L
15/64"
PILOT
HOLE
(2-1/2" REF)
DRILL PILOT HOLE FIRST
INTERIOR OF BATH
HOT WATER
FAUCET HOLE
COLD WATER
FAUCET HOLE
(3" REF)
1-1/2" DIA.
1-1/2" DIA.
15/64"
15/64"
RIB HOLE
RIB HOLE
15/64"
PILOT
HOLE
15/64"
PILOT
HOLE
DRILL PILOT HOLES
AND RIB HOLES
15/64"
15/64"
BEFORE DRILLING
1-1/2" DIA. HOLE
RIB HOLE
RIB HOLE
INTERIOR OF BATH
Jacuzzi Whirlpool Bath
6683000G
8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 1991 Jacuzzi Whirlpool Bath 6683000G 8/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|